For more information, contact us at 1 877-778-5733. 1

Each Fence Panel Box Includes:

This Post & CapNot Included(See note below)

3-Rail Vinyl Ranch Fence (2 Pack)

BOX CONTENTS

Discover the Benefits of WamBam Traditional Vinyl Fence• Made of durable, low-maintenance white vinyl• Post design offers architectural character and flexibility when installing fence• Post design also offers 4-way universal directional capabilities (you do not need to order end, line, corner or specialized gate posts) • Limited Lifetime Warranty

PLEASE NOTE: YOU WILL NEED TO PURCHASE ONEEXTRA POST & CAP TO COMPLETE

EACH OF YOUR FENCE RUNS(Extra posts are sold as 2-packs)

• Post Caps (2)

• Rails (6)

• 3.5in. Stainless Steel Screws (12)

• Posts (2)

.090in. wall thickness

For more information, contact us at 1 877-778-5733. 2

3-Rail Vinyl Ranch Fence (2 Pack)

PRODUCT SPECIFICATIONS This fence can be trimmed down both in width and

height to accommodate custom applications.

4.5in.

1.5in.

.090in. Wall Thickness

Top View4.5in.

4.5in.

3.5in. Screw

Ground2in.

79.5in.

84in.20.5in.

8in.

8in.

19.5in.

51.5in.

50in.

Horizontal rail spacing can be adjusted freely to lower heights.

72in.

10in.

Concrete Footing36in.

For more information, contact us at 1 877-778-5733. 3

3-Rail Vinyl Ranch Fence (2 Pack)

QUICKIE OVERVIEW• Prior to construction, check with your regulatory agency for special code requirements in your area.• Contact your utility supplier to locate and mark underground lines before excavation.• Sketch out the layout of your fence and calculate the number of panels, gates and posts required (order one extra post & cap to finish each fence run).• Careful planning & measuring of your fence is essential, as moving posts after the concrete sets is extremely difficult.

A B

10in.

36in.

1 - Add approximately 18in. of concrete to the bottom of the hole.2 - Install posts straight and level.3 - Add more concrete to within 2in. of ground level.

After stringing your fence line, dig your first post hole 10in. diameter x 36in. deep. Dig your second hole 84in. on center to your first hole, and so on. Dig only three or four holes at a time to ensure proper spacing.

In the first fence section, slide 3 rails downthe groove in your posts to the approximate

position as illustrated on page 2 (rail spacing is flexible).

84in. o.c.

D

In the second fence section, slide 3 rails down the groove in your posts to the approximate position and repeat with any remaining fence sections.

C

79.5in.

Do not overtightenscrews as it will cause

the vinyl to dimple.

E

For more information, contact us at 1 877-778-5733. 4

3-Rail Vinyl Ranch Fence (2 Pack)

Screws must be inserted straight and into the correct area of the post/rail as indicated.

Fasten a 3.5 inch screw through the posts into the rails.

F

Repeat in each rail for a total of six per panel.

This will ensure that your fence rails will never fall outof your posts like traditional

vinyl fence rails sometimes do.

VERY IMPORTANT

SCREW RAILS TO POSTS

Line up and insert screwsalong edge of rounded

corner radius as shown.

TOPVIEW

WRONG

WRONG

CORRECT

Screw has not been lined up nor inserted into the post correctly and has missed the rail entirely.

1 - Put a small bead of vinyl glue or weld (purchased separately at hardware store) along the inside of the cap.2 - Place the glued cap on the vinyl post and allow to set for 5-10 minutes.

For more information, contact us at 1 877-778-5733. 5

3-Rail Vinyl Ranch Fence (2 Pack)

Most yards are relatively level and will allow for a fairly simple installation. If your yard is steeply pitched, or is very uneven, you may need to either slope, or stair-stepyour panels as illustrated below. Post height can be trimmed down as necessary.

GLUE CAPS ON POSTS

Ground

G

Ground

SLOPED

STAIR-STEPPED

Vinyl Weld

21