2G plus 4G IMSI Catcher Equipment Technical Standards
Transcript of 2G plus 4G IMSI Catcher Equipment Technical Standards
1 / 13
2G plus 4G IMSI Catcher Equipment
Technical Standards
2019-02-22
2 / 13
1. System technical indicators
Seri
al
num
ber
Description of
the project Technical parameters Note
1 IMSI Catcher
Protocol
China Mobile 2G GSM900 China Unicom 2G GSM900 China Telecom 2G CDMA China Mobile 4G Band38、Band 39 China Telecom 4G Band3 China Unicom 4G Band3
2
Network
environment Parameter
configuration
2G device has automatic sweep setting
function;
3 Device
Coverage Scope
Coverage:10-1000m, , device power
adjustable, The acquisition module can be controlled RF
on or off. Max. Power 10W/Carrier
4 Backhaul
1. Connect the IMSI catcher device to the
router via a network cable with the
customer's 3G router backhaul;
2. IMSI Catcher have wireless backhaul
capabilities, via Unicom 3G backhaul;
FTP
Protocol
5 Data storage
Front-end equipment has breakpoint
resume transmission and data storage
functions, with a storage capacity of 1
million items
6 Antenna
interface
Three interfaces are 4G, 1 antenna interface
(Mobile / Telecom / Unicom 4G) and 2G, 2
antenna interfaces (Mobile / Unicom /
Telecom). The antenna uses a sucker rod
omnidirectional antenna.
7 Power section AC220V power supply / powered by vehicle
inverter, power consumption of hotspot
IMSI catcher is less than 500W
3 / 13
2. Device Appearance
Vehicle-mounted IMSI devices are divided into two devices, one is a 4G
hotspot device; the other is a 2G hotspot device. A single device chassis is a standard
2U height with a maximum depth of 42cm. Considering the heat dissipation of the
device, a silent fan is added.
1. 4G hotspot equipment (including China Mobile Band38, 39, China Telecom
Band 3, China Unicom Band 3).
2. 2G hotspot equipment (including China Mobile GSM 900, China Unicom GSM
900, and China Telecom CDMA);
4 / 13
3. Device chassis panel interface description (add SIM card slot)Device Chassis
Panel Interface Description (Add SIM slot)
3. Installation diagram
The following is a reference picture of the modified equipment car, which can be
adjusted according to the size of the hot device.
5 / 13
Standar
d 2U
Standar
d 1U
1U
6 / 13
Car-to-power (reference)
4. 4G wireless specifications
System parameters
Working China Mobile:band38、band39 China Telecom: band3、
Unicom:band3
Emission power 10W/Agnieszka
Carrier combination Mobile second carrier, telecommunications one carrier
ACPR -45/-50dBc(Carrier out-of-band 20M test)
EVM Better than 6%
Out-of-band strays Meet the requirements of the 3GPP agreement
Receive sensitivity -104dBm
Receiver Dynamic Range -30dbm~-104dbm
Coverage 10 to 800 m (related to wireless environment and transmit
power)
Capture peak rates 800 groups / minute / carrier
Average capture rate >95%
Fast-moving capture rate >90%
7 / 13
Back to the net time <2S
Main antenna and interface Omnidirectional antenna, one interface
Capture interval time Can be set (3 minutes to 12 hours)
Data transmission 3G network / network cable (optional)
Electrical characteristics
How to install Standard 19-inch rack mount
Power features AC220V
Rated power <200W
Protection level Indoor Standard 2U Chassis
Host weight <16kg
Materials Sheet Metal Spraying
External interface 1 x 10/100M Ethernet port, power interface, RF antenna
interface, backhaul antenna interface,GPS antenna
MTBF,(average time between
failures)
MTBF≥20,000h
Operating temperature,
humidity range
Working temperature -40 to 55 ° C
Storage ambient temperature -45 to 85 ° C
Relative humidity 10 to 95% non-condensing
Working bandwidth 5M
Input voltage range AC165V~300V~300V
5. 4G Product Entities
1)Chassis description
"I'm not going to do that," he2Usaid.
Dimension:420x440x87.5mm
Weight: 16kg
8 / 13
2)Interface description
Serial number Identity Feature Description
Back
1 GPS Antenna Connect GPS Antenna
2 4G Antenna Master business 4G antenna
(directional or omnidirectional)
3 ETH Access
4 AC IN AC220V Power Interface
Positive
5 Power Power switch
6 China mobile 4G Mobile amplifier control switch
7 China Telecom 4G Telecommunications amplifier
control switch
8 Unicom 4G Unicom amplifier control switch
9 Wifi Wifi Remote Maintenance Antenna
10 Yes SIM card slot
11 3G Connect 3G backhaul stick antenna
6. 4G module description
Serial
number
Module name Module specifications and functional
descriptions
1. Power 340W 28V 12V dual-way output
communication product dedicated power
supply
2. Telecommunications
FDD_1867.5 base band
Integrated BBU-RRU feature, band adjustable
3. Unicom FDD_1850 base
band plate
Integrated BBU-RRU feature, band adjustable
9 / 13
4. Heiser 800-2700M 2-in-1-in-one roader
5. Mobile TDD_1895 baseband
plate
Integrated BBU-RRU feature, band adjustable
6. Mobile TDD_2585 baseband
plate
Integrated BBU-RRU feature, band adjustable
7. GPS, power control module Integrated GPS and module power switching
8. 5 Industrial Switches Internal exchange data usage
9. TDD_2.6G PA Amplifier low noise integration, power
amplification
10. TDD_1.9G PA Amplifier low noise integration, power
amplification
11. FDD_1.8G PA Amplifier low noise integration, power
amplification
12. Four-frequency circuit rafters All frequency bands for the same road
13. X86 Control Module Modules, data management
14. 3G Backhaul Router Wireless data backhaul
7. Description of 2G system parameters
System parameters
Working 移动 GSM、联通 GSM、电信 CDMA
Emission power GSM:总功率 10W
CDMA:总功率 10W
Carrier combination Mobile, telecommunications, 一 Unicom each carrier
Out-of-band strays Meet the requirements of the 3GPP agreement
Receive sensitivity -104dBm
Receiver Dynamic Range -30dbm~-104dbm
Coverage 10-1000 m (related to wireless environment and transmit
power)
Capture peak rates 800 group/min/carrier
Average capture rate >95%
Fast-moving capture rate >90%
Back to the net time <2S
Main antenna and interface Omnidirectional antenna, one interface
10 / 13
Capture interval time 3min~12Hr
Data transmission 3G DATA/Net cable
Electrical characteristics
How to install Standard 19-inch rack mount
Power features AC220V
Rated power Full-band dynamic work 160W
Protection level Indoor Standard 2U Chassis
Host weight <12kg
Materials Sheet Metal Spraying
External interface 1 x 10/100M Ethernet port, power interface, RF antenna
interface, backhaul antenna interface,GPS antenna
MTBF,(average time between
failures)
MTBF≥20,000h
Input voltage range AC165V~300V~300V
8. 2G Product Entities
1)Chassis description
Standard 2U Chassis
Dimension:420x440x87.5mm
Weight: 12kg
11 / 13
2)Interface description
Serial number Identity Feature Description
Back
1 CDMA Antenna Connect CDMA Antenna
2 SWP Receiver CDMA glue rod sweep
antenna
3 GSM Antenna Connect GSM Antenna
4 SWP Slat-on GSM glue bar sweep antenna
5 ETH Access
6 AC IN AC220V Power Interface
Positive
7 Power Power switch
8 GSM GSM AMPLIFIER CONTROL SWITCH
9 CDMA CDMA amplifier control switch
10 Wifi Wifi Remote Maintenance Antenna
11 Yes SIM card slot
12 3G Connect 3G backhaul stick antenna
9. 2G module description
Serial
number
Module name Module specifications and functional descriptions
1 Power 340W 28V 12V dual-way output communication
product dedicated power supply
2 Telecom CDMA base band Integrated BBU-RRU feature, band adjustable
3 Mobile Unicom GSM
baseband
Integrated BBU-RRU feature, band adjustable
4 Heiser 800-2700M 2-in-1-in-one roader
12 / 13
5 GPS, power control module Integrated GPS and module power switching
6 5 Industrial Switches Internal exchange data usage
7 CDMA PA Amplifier low noise integration, power amplification
8 GSM PA Amplifier low noise integration, power amplification
9 CDMA duplex CDMA signal on, downstream, filter
10 GSM duplex GSM signal on, downstream, filter
11 X86 Control Module Device control and data management
12 3G Backhaul Router Wireless data backhaul
10. Antenna description
The car antenna is a product designed for mobile communication system equipment. The
antenna is small in size, beautiful in appearance and easy to install.
Technical Parameter
Model TQC-0727UT
Frequency range
-MHz 698~806 806~960 1710~1880 1880~2700
Bandwidth -MHz 108 154 170 820
VSWR ≤2.5 ≤2.0 ≤2.5 ≤2.0
Gain-dBi 3±0.5 5±1
Input Impedance -S 50
How to polarize Vertical
Maximum power
-W 50
Connector model NMO-J
Length -mm 84±2.5
Weight-g 100
Color White
13 / 13
Note: The above electrical performance indicators are equipped with a large
area metal plate test.