2995 XFC Fertilizer Coulter 2995 XCC Cutting Coulter ......2995 XFC Fertilizer Coulter 2995 XCC...

2995 XFC Fertilizer Coulter 2995 XCC Cutting Coulter

OPERATORS MANUAL WITH PARTS IDENTIFICATION

2565-788_REV_D ● 02/2019

YETTER MANUFACTURING CO. FOUNDED 1930

Colchester, IL 62326-0358 Toll free: 800/447-5777

309/776-3222 (Fax) Website: www.yetterco.com

E-mail: [email protected]

2

FOREWORD

You’ve just joined an exclusive but rapidly growing club. For our part, we want to welcome you to the group and thank you for buying a Yetter product. We hope your new Yetter products will help you achieve both goals-increase your productivity and increase your efficiency so that you may generate more profit. This operator’s manual has been designed into four major sections: Foreword, Safety Precautions, Installation Instructions and Parts Breakdown. This SAFETY ALERT SYMBOL indicates

important safety messages in the manual. When you see this symbol, be alert to the

possibility of PERSONAL INJURY and carefully read the message that follows.

The word NOTE is used to convey information that is out of context with the manual text. It contains special information such as specifications, techniques and reference information of a supplementary nature. The word IMPORTANT is used in the text when immediate damage will occur to the machine due to improper technique or operation. Important will

apply to the same information as specified by note only of an immediate and urgent nature. It is the responsibility of the user to read the operator’s manual and comply with the safe and correct operating procedure and to lubricate and maintain the product according to the maintenance schedule in the operator’s manual. The user is responsible for inspecting his machine and for having parts repaired or replaced when continued use of the product would cause damage or excessive wear to the other parts. It is the user’s responsibility to deliver his machine to the Yetter dealer who sold him the product for service or replacement of defective parts, which are covered by the warranty policy. If you are unable to understand or follow the instructions provided in this publication, consult your local Yetter dealer or contact:

YETTER MANUFACTURING CO. 309/776-4111 800/447-5777

309/776-3222 (FAX) Website: www.yetterco.com

E-mail: [email protected]

WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. This warranty does not obligate the Company to bear cost of labor in replacement of parts. It is the policy of the Company to make improvements without incurring obligations to add them to any unit already sold. No warranty is made or authorized to be made, other than herein set forth. This warranty is in effect for one year after purchase.

Dealer ___________________________________________________ Yetter Manufacturing warrants its own products only and cannot be responsible for damages to equipment on which mounted.

3

SAFETY

A brief description of signal words that may be used in this manual:

CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices. WARNING: Denotes a specific potential hazard. DANGER: Denotes the most serious specific potential hazard.

SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. Study these precautions carefully and insist that they be followed by those working with you and for you. Finally, remember this: an accident is usually caused by someone’s carelessness, neglect, or oversight.

WARNING

Never clean, lubricate or adjust a machine that is in motion. Always lower or block the implement before performing service. If machine must be serviced in the raised position, jack or block it up to prevent it from accidentally falling and injuring someone. Do not allow riders on the tractor or implement. Use speeds and caution dictated by the terrain being traversed. Do not operate on any slope steep enough to cause tipping or loss of control. Be sure all personnel are clear of the immediate area before operating. Read and understand the operator’s manual and require all other persons who will operate the equipment to do the same. Be familiar with all tractor and implement controls and be prepared to stop engine and implements quickly in an emergency.

CAUTION

Consult your implement and tractor operator’s manual for correct and safe operating practices. Beware of towed implement width and allow safe clearance.

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH.

4

GENERAL INFORMATION

5

GENERAL INFORMATION

8

MAINTENANCE • After a few hours use, check all bolts and setscrews for tightness.

• After using a few hours, check for loose hardware, re-tighten as needed.

• After a few days use, check coulter hubs for loose bearings. There should be no end play in the hub

bearings to allow it to wobble. If necessary, remove hub cap and cotter pin, adjust slotted nut to remove wobble, re-insert cotter pin and replace hub cap.

LUBRICATION

DANGER: Always install safety lock-ups or lower the planter to the ground before working on the machine. Lubricate at frequency indicated with a multi-purpose type grease.

ISO 2995-086

DANGER: Always install all safety lock-ups and safety lock pins before working under the toolbar.

1. Raise the toolbar until is clear off the ground. Remove the gauge wheel and the blade. Remove the hubcap, cotter pin, slotted nut and washer from the spindle shaft assembly.

2. Pull the coulter spindle shaft assembly from the hub. Remove bearing cones and cups and discard if bearings are being replaced. Clean hub and dry. Remove bearings only and not cups of re-packing.

3. Wash the old grease from the hub, bearing cups, coulter spindle shaft, seal, and bearing cones. Inspect the condition of bearing cups and cones.

4. Apply #2 multi-purpose lithium grease on each bearing. Make sure the space around each roller is filled. Lubricate the bearing cups.

5. Position the bearing in the cup and install the seal. Lubricate the seal lips and proceed with re-assembly of the removed parts including the blade. Blade bolt torque is 90 to 96 ft. lbs.

6. Install outer bearing, washer, and slotted nut. Tighten the slotted nut to 150 in. lbs. while rotating the blade or until a definite drag is felt when the blade is turned by hand. Tighten the nut one slot position to line up the cotter pin hole with a slot. Secure the nut with a new cotter pin.

9

ASSEMBLY INSTRUCTIONS

STEP 1. Install shank to the coulter assembly.

10


STEP 2. Install roll pin to the shank.

11


STEP 3. Attach the blade to the coulter assembly using the 4) ½” – 20 X 1” Hex Head Bolts.

12


STEP 4. Attach the toolbar clamp to the frame.

13


STEP 5. Loosely assemble the set screws and lock nuts to the toolbar clamp.

14


STEP 6. Slide shank into the toolbar clamp. Install roll pin to the shank.

15


STEP 7. Adjust coulter shank up or down as needed to securely tighten 2) set screws.

STEP 8. If using fertilizer, install the 2995-083 injector or 2995-084 knife as shown in the parts identification section of this manual. NOTE: When installing the 2995-084 knife kit, bend the fertilizer tube slightly enough to allow clearance for the 2502-367 ½ x 4” knife lock bolt – see photo illustrations.

Bend tube slightly

enough to allow

clearance for the

2502-367 ½” x 4”

Knife lock bolt Bend tube slightly

enough to allow

clearance for the

2502-367 ½” x 4”

Knife lock bolt

16

PARTS IDENTIFICATION

17


18

PARTS IDENTIFICATION COULTER ASSEMBLY

2995-197-RH

19

PARTS IDENTIFICATION COULTER ASSEMBLY LH

2995-197-LH

20


21

PARTS IDENTIFICATION COULTER ASSEMBLY

2995-153

22


23


2995-149

24


2995-138

25


26


27


28


29


30


31

TROUBLESHOOTING

32

NOTES:

33

NOTES:

34

NOTES:

35

NOTES:

36

Our name Is getting known

Just a few years ago, Yetter products were sold primarily to the Midwest only. Then we embarked on a program of expansion and moved into the East, the South, the West and now north into Canada. We’re even getting orders from as far away as Australia and Africa. So, when you buy Yetter products . . .you’re buying a

name that’s recognized. A name that’s known and respected. A name that’s become a part of American agriculture and has become synonymous with quality and satisfaction in the field of conservation tillage. Thank you.

YETTER MANUFACTURING CO. Colchester, IL 62326-0358 � 309/776-4111

Toll Free 800/447-5777 Fax 309/776-3222

Website: www.yetterco.com E-mail: [email protected]

2565-788_REV_D �

02/2019

2995 XFC Fertilizer Coulter 2995 XCC Cutting Coulter ......2995 XFC Fertilizer Coulter 2995 XCC...

Documents

Transcript of 2995 XFC Fertilizer Coulter 2995 XCC Cutting Coulter ......2995 XFC Fertilizer Coulter 2995 XCC...