2722 - AYN License Plate Frame and Module Instruction - AYN License Plate Frame an… · We...
1
We recommend placing this card with your bikes tool kit or owner's manual to use as a future reference for changing your bikes brake modes, or to engage Hazard Flashers or Night Rider mode. To engage Emergency Hazard Flashers without the use of an optional switch: Turn Right turn signal on, apply brakes and turn the bikes key switch off. When the hazard flasher is turned on this way it will continue to flash until the bikes key switch is turned back on. The Night Rider mode is meant to draw attention to your bike at bike shows, rally's, or bike nights. To engage Night Rider Mode without the use of an optional switch: Turn Left turn signal on, apply brakes and turn the bikes key switch off. When the Night Rider mode is turned on this way it will continue to flash until the bikes key switch is turned back on. TECH SUPPORT MONDAY - FRIDAY 9AM-5PM E.S.T. 800.785.1814 BE NOTICED... BE SEEN... BE SAFE! AYN LICENSE PLATE FRAME & AYN SMART MODULE Mounting: It is recommended that the module be mounted in a location not subject to extreme heat conditions or near high voltage areas such as your ignition coil or spark plug wires. It can be mounted with the included double sided adhesive tape or any other suitable means. INSTALLATION Below is a basic wiring diagram for our AYN License Plate Frame when installed WITHOUT the AYN Smart Module (sold separately). Below is a basic wiring diagram for our AYN License Plate Frame when installed WITH the AYN Smart Module (sold separately) - added benefits listed above. GROUND BRAKE LIGHT SWITCHED POWER SOURCE (RUNNING LIGHT) IF YOU INSTALL THE FRAME ALONE, FOLLOW INSTALL OPTION 1. IF YOU HAVE THE FRAME AND SMART MODULE CHOOSE INSTALL OPTION 2. INSTALL OPTION 1 INSTALL OPTION 2 SWITCHED POWER SOURCE (RUNNING LIGHT) SHOW MODE HAZARD (WHITE WIRE) (SWITCHES AND FUSE NOT INCLUDED*) CAP OFF WIRES IF NOT USED TOGGLE SWITCH (NOT INCLUDED) POSITVE BATTERY POWER 5 AMP FUSE (NOT INCLUDED) TAP CONNECT GROUND 5 AMP FUSE (NOT INCLUDED) 5 AMP FUSE (NOT INCLUDED) 2. This Frame was designed to match the bolt hole pattern of most states license plates. It may be necessary to adjust the holes of the license plate to accommodate the frame. This can be done easily with the use of a round file. If adjustment is necessary, it is minimal. 3. Determine where and how to run the wires from the L.E.D. light array to the motorcycle's wiring. (see diagrams and wiring instructions below. Additional lengths of connecting wire may be required (not provided). 4. Included are 4 rear mount stud screws, washers and locking nuts. Insert the stud screws into the holes on your AYN frame and use a 3/16 alan wrench to torque them down tight to prevent loosening from vibration. Then add the washer and nut to secure the frame and license plate in place. 5. We reccomend that you first test our AYN license plate frame on a known 12V power source prior to installation to ensure proper function. 1. To accommodate the wires from the L.E.D. array (if necessary) it is recommended to file a notch in the license plate to prevent chaffing of the wires. Do not pinch the wires between the frame and the plate as this could cause the LED's to malfunction. PLEASE READ BEFORE INSTALL When installing the AYN Smart module in combination with the AYN frame you will need to know about the 4 user selectable modes and how to switch to the one you want. In the event you install the AYN frame with the AYN module, a reference sheet of what modes you have to choose from and how to switch them is provided. Print these instructions out and cut along the dotted line so you can easily place the sheet into your glovebox or saddlebag for reference. *THE GREEN AND WHITE WIRES FROM THE MODULE CAN CONTROL YOUR HAZARD FLASHERS AND 'NIGHT RIDER' MODE WITH A SWITCH (NOT INCLUDED) RATHER THAN USING HAND CONTROLS, THIS IS OPTIONAL. *Three slow flashes, steady, then repeat To change brake flash modes: Within 10 seconds after turning the bike on, press and release the brakes the number of times in the table below to change brake modes. (Wait until the end of the 10 seconds before pressing the brakes again to avoid switching to an unwanted mode). Brakes will remain in this mode until they are changed again by the user. PRIOR TO INSTALLATION
Transcript of 2722 - AYN License Plate Frame and Module Instruction - AYN License Plate Frame an… · We...
We recommend placing this card with your bikes tool kit or owner's manual to use as a future reference for changing your bikes brake modes, or to engage Hazard Flashers or Night Rider mode.
To engage Emergency Hazard Flashers without the use of an optional switch: Turn Right turn signal on, apply brakes and turn the bikes key switch off. When the hazard flasher is turned on this way it will continue to flash until the bikes key switch is turned back on.The Night Rider mode is meant to draw attention to your bike at bike shows, rally's, or bike nights. To engage Night Rider Mode without the use of an optional switch: Turn Left turn signal on, apply brakes and turn the bikes key switch off. When the Night Rider mode is turned on this way it will continue to flash until the bikes key switch is turned back on.
TECH SUPPORTMONDAY - FRIDAY9AM-5PM E.S.T.800.785.1814
BE NOTICED... BE SEEN... BE SAFE!
AYN LICENSE PLATE FRAME & AYN SMART MODULE
Mounting: It is recommended that the module be mounted in a location not subject to extreme heat conditions or near high voltage areas such as your ignition coil or spark plug wires. It can be mounted with the included double sided adhesive tape or any other suitable means.
INSTALLATION
Below is a basic wiring diagram for our AYN License Plate Frame when installed WITHOUT the AYN Smart Module (sold separately).
Below is a basic wiring diagram for our AYN License Plate Frame when installed WITH the AYN Smart Module (sold separately) - added benefits listed above.
GROUND
BRAKE LIGHT
SWITCHEDPOWER SOURCE(RUNNING LIGHT)
IF YOU INSTALL THE FRAME ALONE, FOLLOW INSTALL OPTION 1. IF YOU HAVE THE FRAME AND SMART MODULE CHOOSE INSTALL OPTION 2.
INSTALL OPTION 1 INSTALL OPTION 2
SWITCHEDPOWER SOURCE(RUNNING LIGHT)
SHOW MODEHAZARD
(WHITE WIRE)
(SWITCHES AND FUSE
NOT INCLUDED*)
CAP OFF WIRES IF NOT USED
TOGGLE SWITCH(NOT INCLUDED)
POSITVE BATTERY POWER
5 AMP FUSE(NOT INCLUDED)
TAP CONNECT
GROUND
5 AMP FUSE(NOT INCLUDED)
5 AMP FUSE(NOT INCLUDED)
2. This Frame was designed to match the bolt hole pattern of most states license plates. It may be necessary toadjust the holes of the license plate to accommodate the frame. This can be done easily with the use of a round file. If adjustment is necessary, it is minimal.
3. Determine where and how to run the wires from the L.E.D. light array to the motorcycle's wiring. (see diagrams and wiring instructions below. Additional lengths of connecting wire may be required (not provided).
4. Included are 4 rear mount stud screws, washers and locking nuts. Insert the stud screws into the holes on your AYN frame and use a 3/16 alan wrench to torque them down tight to prevent loosening from vibration. Then add the washer and nut to secure the frame and license plate in place.
5. We reccomend that you first test our AYN license plate frame on a known 12V power source prior to installation to ensure proper function.
1. To accommodate the wires from the L.E.D. array (if necessary) it is recommended to file a notch in the license plate to prevent chaffing of the wires. Do not pinch the wires between the frame and the plate as this could cause the LED's to malfunction.
PLEASE READ BEFORE INSTALLWhen installing the AYN Smart module in combination with the AYN frame you will need to know about the 4 user selectable modes and how to switch to the one you want. In the event you install the AYN frame with the AYN module, a reference sheet of what modes you have to choose from and how to switch them is provided. Print these instructions out and cut along the dotted line so you can easily place the sheet into your glovebox or saddlebag for reference.
*THE GREEN AND WHITE WIRES FROM THE MODULE CAN CONTROL YOUR HAZARD FLASHERS AND 'NIGHT RIDER' MODE WITH A SWITCH (NOT INCLUDED) RATHER THAN USING HAND CONTROLS, THIS IS OPTIONAL.
*Three slow flashes, steady, then repeat
To change brake flash modes: Within 10 seconds after turning the bike on, press and release the brakes the number of times in the table below to change brake modes. (Wait until the end of the 10 seconds before pressing the brakes again to avoid switching to an unwanted mode). Brakes will remain in this mode until they are changed again by the user.
PRIOR TO INSTALLATION
