220KV Moti Gop AIS SUBSTATION Schedule No. 4 … Office/0-2016/260416_A... · Tandem DB Isolator...

Local Currency

Foreign Courancy

Local Currency

Foreign Courancy

1 2 4 5 6=3X4 7=3X5PART - A (Related Services includes)

(I) SWITCHYARD PART

ASupply and Erection of 220kV Equipments (as per respective technical specifications and relevant special conditions) suitable for One Main Bus and One Main cum Transfer Bus scheme

1 Surge Arrester 198kV, 10kA, Cl-3 with structure and clamp connectors as per Technical spec No. 24

2 PT 220kV/√3-/110V/√3-3C with structure and clamp connectors as per Technical spec No. 6

3 BPI 8kN with structure and clamp connectors as per Technical spec No. 1574 HBPI 8kN with structure and clamp connectors as per Technical spec No. 39

5 HDB Isolator with one ES 1600A 40kA 3s with structure and clamp connectors as per Technical spec Set. 8

6 HDB Isolator without ES 1600A 40kA 3s with structure and clamp connectors as per Technical spec Set. 19

7 Tandem DB Isolator 1600A 40kA 3s with structure and clamp connectors as per Technical spec Set. 9

8 CT conventional 1500-1200-600/1, 5C with structure and clamp connectors as per Technical spec No. 27

9 CB 2000A 40kA 3s with structure and clamp connectors as per Technical spec Set. 9

BSupply and Erection of 220kV Switchyard material (as per respective technical specifications and relevant special conditions) suitable for One Main Bus and One Main cum Transfer Bus scheme

1 Gantry structures GI as per BOM, Steel & A/B part MT 123.12 Gantry structures GI as per BOM, Bolt nut part MT 5.4

3 VHF Tower Mast Structure GI with stub, template complete as per BOM, Steel & A/B part MT 1.65

4 VHF Tower Mast structures GI with stub, template complete as per BOM, Bolt nut part MT 0.1

5

Stringing of bus with Twin AL59(61/3.50) conductor for all the three phases with required Silicon Rubber Insulators, hardwares & accessories, spacers provided at every 3.0 mtr. interval etc. complete as per relevant standards and approved drawings with Jumpers for continuous Bus Arrangement (It includes cost of Conductor, Silicon Rubber Insulators, hardwares & accessories, spacers etc.all items required for satisfactory functioning. Any variation in quantities shall be absorbed by contractor.

a Main Bus with 36Mtr span including bus jumpers No. of Span 12b Line flyover bus with 57Mtr span No. of Bay 8c Transformer flyover bus with 57Mtr span No. of Bay 3d Bus Coupler Flyover Bus with 57 Mtr. Span No. of Bay 1

220KV Moti Gop AIS SUBSTATION Schedule No. 4 Installation and Other Services

4

Unit of Measurement Quantity

DescriptionSr No

Unit Price Total price per item

of 45


Unit of QuantityDescription

Sr NoUnit Price Total price per item

6

Stringing of Earth Wire with 7/3.15 GS wire with required hardwares & accessories etc. complete as per standards and approved drawings for span of 57 meters.(It includes cost of Earthwire,hardwares & accessories, etc. all items required for satisfactory functioning. Any variation in quantities shall be absorbed by contractor

Span 13

7

Droppers (including required suspension string with hardware & accessories if any) & Jumpers (including Equipment to Equipment) with Twin AL59(61/3.50) conductor as per standards and approved drawings with provision of required spacers( Suitable for 350mm spacing) at every 3.0 mtr. interval .(It includes cost of Conductor,Silicon Rubber Insulators, hardwares & accessories, Fire Wedge connectors, spacers etc.all items required for satisfactory functioning. Any variation in quantities shall be absorbed by contractor)

a 220/66KV Transformer Bay No. of bay 2b 220KV Line Bay No. of bay 6c 220KV Bus Coupler Bay No. of bay 1

8

Droppers (including required suspension string with hardware & accessories if any) & Jumpers with Single AL59(61/3.50) conductor as per standards and approved drawings (It includes cost of Conductor,Silicon Rubber Insulators, hardwares & accessories, Fire Wedge Connectors, etc.all items required for satisfactory functioning. Any variation in quantities shall be absorbed by contractor)

a 220KV Line Bay - LA & CVT No. of bay 6b 220/66KV Transformer Bay - LA No. of bay 2c 220KV PT Bay No. of bay 2

CSupply and Erection of 66kV Equipments (as per respective technical specifications and relevant special conditions) suitable for Two Main Bus scheme

1Power Transformer 66/11kV, 5 MVA with oil and accessories connector suitable for Single AL59(61/3.50) No. 1

2 Surge Arrester 60kV, 10KA, Class 3 with structure and clamp connectors suitable for Single AL59(61/3.50) No. 27

3 PT 66kV/v3-/110V/v3-2C with structure and clamp connectors suitable for Single AL59(61/3.50) No. 6

4 BPI 4kN with structure and clamp connectors suitable for Single AL59(61/3.50) No. 56

5 BPI 4kN with structure and clamp connectors suitable for Twin AL59(61/3.50) No. 28

6 HBPI 4kN with structure and clamp connectors suitable for Twin AL59(61/3.50) No. 6

7 HDB Isolator with one ES 1250A 25kA 3s with structure and clamp connectors suitable for Single AL59(61/3.50) Set. 6

8 HDB Isolator without ES 1250A 25kA 3s with structure and clamp connectors suitable for Single AL59(61/3.50) Set. 15

9HDB Isolator without ES 1250A 25kA 3s with structure and clamp connectors suitable for Single AL59(61/3.50) (3nos./set) & Twin AL59(61/3.50) (3nos./set)

Set. 2

10 HDB Isolator without ES 2000A 25kA 3s with structure and clamp connectors suitable for Twin AL59(61/3.50) Set. 6

of 45




11 CT 600-300/1 3C, 31.5KA 3S with structure and clamp connectors suitable for Single AL59(61/3.50) No. 18

12 CT 1600-1200/1 3C 31.5KA 3S with structure and clamp connectors suitable for Twin AL59(61/3.50) No. 9

13 CT 100-50/1 3C 31.5KA 3S with structure and clamp connectors suitable for Single AL59(61/3.50) No. 3

14 CB 1600A 25kA 3S with structure and clamp connectors suitable for Single AL59(61/3.50) Set. 7

15 CB 1600A 25kA 3S with structure and clamp connectors suitable for Twin AL59(61/3.50) Set. 3

DSupply and Erection of 66kV Switchyard Materials (as per respective technical specifications and relevant special conditions) suitable for Two Main Bus scheme

1 Gantry structures GI as per BOM , Steel & A/B part MT 43.72 Gantry structures GI as per BOM , Bolt nut part MT 5.2

3

Stringing of bus for all the three phases with Twin AL59(61/3.50) conductor, Silicon Rubber Insulators hardwares, spacers(suitable for 350mm spacing) at interval of 4.0 mtr complete as per relevant standards and approved drawings.(The scope includes the cost of Silicon Rubber Insulators, hardwares, accessories, spacers etc.all items required for satisfactory operation. Any variation in quantities shall be absorbed by erection contractor.

a Main Bus with 33.800 Mtr. Span including bus jumpers Span 2b Main Bus with 33.950 Mtr. Span including bus jumpers Span 4c Transformer flyover bus with 54.7Mtr. Span No. of bay 2d Transformer flyover bus with 16.4 Mtr. Span No. of bay 2

4

Stringing of bus for all the three phases with Single AL59(61/3.50) conductor, Silicon Rubber Insulators hardwares as per relevant standards and approved drawings.(The scope includes the cost of Silicon Rubber Insulators, hardwares, accessories, spacers etc.all items required for satisfactory operation. Any variation in quantities shall be absorbed by erection contractor.

a Line flyover bus with 23.8 Mtr. Span No. of bay 8b 66/11KV Trf. flyover bus with 23.8 Mtr. Span No. of bay 1

5

Stringing of Earth Wire with 7/3.15 GS wire with required hardwares & accessories etc. complete as per standards and approved drawings for the shown span. (It includes cost of hardwares & accessories etc. all items for satisfactory functioning. Any variation in quantities should be absorbed by erection contractor.

a Main Bus with 33.950 Mtr. Span Span 2b Other Requirements with

22.7 Mtr. Span Span 116.1 Mtr. Span Span 1

c Line flyover bus with 23.8 Mtr. Span No. of bay 7d 66/11KV Trf. flyover bus with 23.8 Mtr. Span No. of bay 1e Transformer flyover bus with 54.7 Mtr. Span No. of bay 4f Transformer flyover bus with 16.4 Mtr. Span No. of bay 4

of 45




6

Droppers (including required suspension string with hardware & accessories if any) & Jumpers with Single AL59(61/3.50) conductor as per standards and approved drawings. (It includes cost of Silicon Rubber Insulators, Fire wedge connectors,hardwares & accessories etc. all items required for satisfactory functioning. Any variation in quantities shall be absorbed by erection contractor)

a 220/66KV Transformer Bay - LA No. of bay 2b 66KV PT Bay No. of bay 2c 66KV Line Bay No. of bay 6d 66/11KV Transformer Bay No. of bay 1

7

Droppers and Jumpering (equipment to equipment) with Twin AL59(61/3.50) conductor as per standards and approved drawings with provision of spacers suitable for 350mm spacing at 4.0 mtr interval. (The scope includes the cost of accessories ,spacers, fire wedge connectors etc.all items required for satisfactory operation.

a 220/66KV Transformer Bay (66KV side) No. of bay 2b 66KV Bus Coupler Bay No. of bay 1

ESupply and Erection of General purpose equipments and materials as per respective technical specifications and relevant special conditions.

1

Suitable arrangement of 11KV connection (A) from 5 MVA station TR to one no. of 11kV/415V, 500 kVA distribution transformer which comprises of: 1) 22 kV outdoor CT having ratio 300-150/1-1-0.577A, STC: 25 kA – 3 sec, BIL 55/150 kVp.2) 22 kV outdoor VCB, 1250A, STC: 25 kA – 3 sec, BIL 55/150 kVp.3) 22 kV outdoor Isolator, 630A, STC: 25 kA – 3 sec.4) 9 KV LAwith support structure, insulated conductor and DP structure with DO fuse, 22kV BPIs arrangement including Dist box suitable to dist transformer. and (B) from separate 11 KV express feeder (feeder termination shall be arranged by GETCO) to another 11kV/415V, 500 kVA distribution transformer which comprises of:1) 22 kV outdoor Isolator, 630A, STC: 25 kA – 3 sec.2) 9 KV LAwith support structure, insulated conductor and DP structure with DO fuse, 22kV BPIs arrangement including Dist box suitable to dist transformer. (11KV Power Cable shall be supplied by GETCO, however Laying of cable with termination kit supply and installation is in the scope of bidder)

Package LS

2 AC unit 3 Ton Split (Reputed make) No. 53 AC unit 1.5 Ton Split (5 star rating and reputed make) No. 2

4

Distribution Transformer 11kV/415V,500 kVA with suitable Dist. Box and its fixing -mounting arrangement as per drg. No. GETCO/E/2S-STD/P-031/LTD R0,Dtd. 11-03-15. Required LT Distribution boxes with LT cable and changeover switch supply is in the scope of bidder.

No 2

5 Providing major spares as per Ann A attached herewith

of 45




a) DG set ( portable three phase 415V 10 KVA Honda / Kirlosakar make) Set 1

b) Welding M/C: Input volt.230-440V(single/two phase), 50Hz, Insulation class A, 200 Amp. With 30 m welding cable Set 1

6 Providing instruments as per Ann B attached herewitha)Computer set with UPS dust cover etc as per technical specifications ( for officer in charge)

Set 1

b) A-4 size mono lasor printer as per technical specifications.( for officer In charge)

Set 1

c) Earth Resistance Tester Digital GE-OHM C make (made in Germany) model no EN 61557/VDE 0413 or updated version with better features.

No. 1

d) Clip on meter AC/DC V/I/OHM - 0-1000V, 0-25A Meco/Rishabh/Motwane Battery backup

No. 1

e) Motor and manual Operated Oil BDV testing Kit –Motwanemake with 0-100kV range, auto cut off feature, with standard ball -cup and measuring gauge as per IS.

No. 1

f) Hydraulic Platform with Loading Capcity of 350kg. and height of 10m (Firefly Energy Ltd Make,Model-A.N.I.L)/(VANJAX Make, Model-VXLTM-350/11000)

No. 1

g)Insulation Resistance Tester (Test volt upto 5kV, Range 100kohm to 10 Tohm), Megger Make, Model-S1568

No. 1

h)Tan Delta Kit- Doble Make (Model-M4100)/ Megger (Delta-4000) with Laptop

Set 1

i) SF6 gas evacuation testing kit with all accessories (make : DILO, Model : 3-001-4-R002)

No. 1

j) Emergency Power Supply Unit (Make- Aux Power- Wavelength system & solution,Output voltage-220V DC)

No. 1

k)CB Analyzer with 6-Channel DCRM kit with all required accessories suitable for GIS Model: HiSAC-Ultima –SCOPE make with suitable Laptop

No. 1

l)LCM Kit (Range :Total leakage current- 200µA to 9mA, Resistive leakage current- 1µA to 9mA) Make : Doble- LCM 500(Wireless) No. 1

7 Providing tools and tackles etc. as per Ann C attached herewith a)Earthing Rod (Highly insulated FRP telescopic Earthing/ Discharge Rod. with cable suitable for 400 & 220kV Switchyard- National Make No. 18

b)Spanner [Ring, Fixed, Box] Fix=10x11,12x13,14x15,,16x17Ring=10x11,12x13,14x15,16x17 Tubular=12x13,14x15,16x17,18x19 Screw driver=827I,927 Nut driver= 7mm - Taparia/Gedore/Zalani Make

Set 3

c) Steel Roller -Size 1" No. 10d) Aluminium Roller -Size 4" No. 5 e) One/two/three Wheel pulley -Size 1" (Gadore) No. 2 f) Winch Machine with Handle -05 Ton Capacity No. 2

of 45




g) Hydraulic Press Machine with Dog, panther, zebra & moose dye sets--100 Ton Capacity ( Hydraulic force ent. / Techno spent ) No. 2

h) Hand drill Wolf Make 240 V Capacity :-Hole up to 31 mm , Single Phase No. 1

i) Drill Machine -5/8" Dia Wolf Make Standing Drill machine having 3 Feet Pillar & suitable for making Holes up to ¾”. Motor No. 2

j) Chain pulley block -5 tonne capacity (Morries) No. 2 k) Wire rope pulley block -02 Tonne (Morries) Set 1l) Tent-Standard quality water proof Tent made from H.D.P.E. Materials with 5 Nos of bamboos Rods and having capacity of 8 to 10 Person to stay & size 10 Ft x 10Ft Multipurpose

Set 1

m) Water pump (Crompton Make) Set -5 HP with hose pipe of 30 m Crompton Make No. 2

n) Crowbar -1.5 Mtr No. 5 o) Crowbar -1.0 Mtr No. 5 p) Hammer with wooden handle -10Kg No. 1 q) Pickaxe ( Trikam) -2 '' width with handle No. 5r) Pawda[shovel] -12 '' width with handle No. 5 s) Axe (Kuhadi) with handle No. 5t) Sythe (Dharia) with handle No. 10 u) Tar Poline (Tad Patri) 5X5 m (HDPE), 200 GSM No. 5v) Nylon Rope -0.5" Dia -100 mtrs (Garware Make) Set 1w) Nylon Rope 0.75" Dia -100 mtrs (Garware Make) Set 1 x) Nylon Rope -1" Dia -100 mtrs (Garware Make) Set 1y) Aluminium Ladder -15 ft. Aluminium folding factory ladder (Heavy duty) made from high tensile aluminium alloy design no 152 AFFL 15 Ft height (4.56 mtrs) specification section= 15/8” X 1.1/4” Steps= 15/8 X 1.1/4 12”Center to Center

Set 1

z) Telescopic aluminium ladder(3 sections) with platform -25 ft No. 1 aa) Hot air blower (Wolf Make) Small Capacity =1.5m3/min, No. 1 Big Capacity =2.0m3/min No. 1 ab) Vaccum cleaner -Eureka Forbes Make (Industrial) No. 1Safety Toolsa) Full body Harness as per technical specification No. 15 b) Halmet with ISI mark of reputed make No. 10 c) Hand Gloves Hand gloves of quality as per IS certification 4770 & test potential 7500Volt Set 6

d) Gum boot (Pair) -Size 8,9,10. -Standard make (Pair for each size) Set 3Display Boards and others a) Single line diagram drawn with radium paint on a board of approx size of 1200x900 mm with fixing arrangement on control room wall. Set 1

b) Key board with hook for different keys of each equipments/panels/cubicles with SLD drawn with color approx size 2'x2' Set 1

8 Supply of Furniture, RO Water Filter System, Water Cooler Etc. as per Ann. DFurniture for 220KV S/S a) Cushioned chair of Godrej make no. Ch-1018D No. 3 b) Steel rack of size 30"X36"X15" with three partitions, prepared 20 gauges No. 2

of 45




c) Providing Control Room Table modular 5X5 Panta work surface with pedestal CPU Trolley & Key Board tray of Godrej or equivalent No. 1

d) Office table with SDU & pedestal 5026 Godrej make No. 2 e) Modular workstations of Godrej make or equivalent 4X2 Panta work surface with pedestal CPU trolley & keyboard Tray or equivalent No. 2

f) Revolving chair PCH -5D02-STAR R-MID BACK No. 4

g) Three seater perforated chair with powder coating(Bench)No. 1

2 RO water filter system 25Ltr. Capacity No. 1

3

Water Cooler Providing & installing SHRIRAM USHA or equivalent make water cooler of 40Ltr./hr. capacity suitable to operate on 230V+10% , 50Hz. Single phase AC supply with hermetically sealed type suction cooled compressor with overload protection confirming to IS 106

No. 1

9 Supply and Erection of Fire stand with 4 buckets including concreting asper our drawing & Instruction of E. I. C. Set 1

10 Providing of Insulating Mat as per IS 15652:2006(Size2000x1000x2mm) in control room No. 72

11Supply and installation of ISI marked fire extinguishers of various typesrequired for220 KV sub station.

1) Dry chemical powder type of 9 Kg. capacity. No. 22) Dry chemical powder type of 25 Kg. capacity. No. 13) Dry chemical powder type of 50 Kg. capacity. No. 14) Carbon dioxide ( CO2) gas type of capacity 6.5 Kg. capacity No. 25) Carbon dioxide (CO2) gas type of capacity 22.5 Kg. capacity No. 16) Mechanical Foam type of capacity 9 LT. No. 27) Mechanical Foam type of capacity 50 LT. No. 1

F

Supply and installation of materials for Illumination system in allrespect as per respective specifications and special conditions (Sucessful bidder has to submit the complete design and BOQ forapproval)

1

Providing & Fixing of Energy Efficient LED type (Techhnical spec Cl No. 2.10.4.8-I LED 3 type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs.as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point,Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp , DC Plug etc all items as per Ann-4 in following rooms (with safety device ELCB)

i Control Room Package LSii PLCC Room Package LSiii Office Package LS

1

of 45




2

Providing & Fixing of Energy Efficient LED Type (Techhnical spec Cl No. 2.10.4.8-I LED 1 or I LED 2 type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs.as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point, Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp , DC Plug etc all items as per Ann-4 in following rooms (with safety device ELCB)

i Battery Room Package LSii LV Room Package LSiii Store Room Package LSiv Ramp Slope Package LSv Veranda Package LSvi Toilet Gents Package LSvii WC Package LSviii Toilet Ladies Package LSix Passage (Corridor) Package LSx Water Room Package LSxi Security Cabin Package LS

3

Providing & Fixing of Energy Efficient LED Type (Techhnical spec Cl No. 2.10.4.8-I LED 1 or I LED 2 type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs.as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point, Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp , DC Plug etc all items as per Ann-4 in following room.

i Store building Package LS

4

Providing & Fixing of Energy Efficient Indoor 2x36 Tube light for Quaters (4 Nos.) in all the rooms, passages complete (ref. Ann-4) as per technical spec with required casing caping point wiring as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan,with requisite MCBs and as per Ann-4 in following amenities

1 Drawing room of Type IV Qtr Package LS2 Bedroom 1of Type IV Qtr Package LS3 Bedroom 2 of Type IV Qtr Package LS

5

Providing & Fixing of Energy Efficient Indoor luminaries in all the rooms, passages Qtr (4 Nos.) complete (ref. Ann-4 as per technical spec Cl No. 2.10.4.8 (CFL type) with required casing caping point wiring as per technical spec. Scope also includes providing and fixing of 15/5 A plug, as per Ann-4 in following rooms--- With supply and fixing of 3 KW Geyser (Instant type Sphere hot make ) Arrangement in bathroom or attached toilet blocks

1 Passage for Type IV Qtr Package LS2 Toilet common for Type IV Qtr Package LS3 Toilet attached to Room No1 for Type IV Qtr Package LS4 Kitchen for Type IV Qtr Package LS5 Store for Type IV Qtr Package LS

of 45




6

Providing and fixing of flood light luminaries as per design for whole switch yard area ( 220 & 66kV) with Energy Efficient LED type (Techhnical spec Cl No. 2.10.4.8-I LED 5 Type) Outdoor luminaries as per design calculation, with respect to required lux level & relevant tender drgs., and required industrial grade point wiring as per technical spec.& ancillaries and suitable for mounting on structure at appropriate height as per specifications TS illuminations cl. no 2.10.4.8 with necessary GI fabrication & GI bolt nuts to fix control gear box at the structure with complete internal and external wiring to J. box ,Dist panel/section feeder pillar etc with supply of required 3 c x 2.5 mm2 copper armoured cable (as per spec ) .The scope includes supply and erection of all the materials required for satisfactory functioning of above work.

Package LS

7

Providing and installation of Energy efficient LED type post top lantern for main gate and road from main gate to switchyard via control room as per design with Philips/CGL/Bajaj/GE/Oshram make & ancillaries suitable for mounting on Gate pillars and 4.5 mtr poles with necessary GI fabrication & GI bolt nuts to fix control gear box with complete internal and external wiring to J.box,Dist panel/section feeder pillar, fixing terminal etc. with supply of required 3 c x 2.5 mm2 copper armoured cable as per spec .This also includes the supply and erection of required 4.5 mtr poles and its foundation work as per spec and earthing with main mesh. The scope includes supply and erection of all the materials required for satisfactory functioning of above work.

Package LS

8

Providing and fixing of street light luminaries for reamaining area (like road, near whole compound wall/fencing area etc.) of switch yard complete as per design with Philips/CGL/Bajaj/GE/Oshram or Similar make LED lamp & ancillaries suitable for mounting on 7.0 mtr swaged poles as per spec.TS illuminations cl. no 2.10.4.8 (S-LED) at appropriate height with necessary GI fabrication & GI bolt nuts to fix control gear box with complete internal and external wiring to J. box ,dist panel/section feeder pillar, fixing terminal etc with supply of required 3 c x 2.5 mm2 copper armoured cable (as per spec). This also includes the supply and erection of 7.0 mtr swaged pole and foundation work as per spec. and panting with two coats of primer and two priming of zinc chromate as well as earthing with main mesh. The scope includes supply and erection of all the materials required for satisfactory functioning of above work.

Package LS

9

Supply and Erection of main lighting Panel ACP-1 as per Specifications. Set comprises minimum 3 nos.of such panels qty may be more if required as per design.Scope also includes the providing and erection of cable size (as per design requirement) and 25x6 GI strip for earthing with main mesh

Set 1

10

Supply and Erection of main lighting Panel ACP-2 as per Specifications Set comprises minimum 2 nos.of such panels qty may be more if required as per design.Scope also includes the providing and erection of cable size (as per design requirement) and 25x6 GI strip for earthing with main mesh

Set 1

of 45




11


Set 1

12


Set 1

13

Supply and Erection of main Yard light Dist. Board as per designed capacity ratings.Scope also includes the providing and erection of cable size (as per design requirement) and 50x6 GI strip for earthing with main mesh

Nos 2

14

Supply and Erection of Lighting Transformers as per designed capacity.Scope also includes the providing and erection of cable size ( as per design requirement) and 50x6 GI strip for earthing with main mesh. Please refer the drawing "General Schematic for Illumination" in the TS Illumination.

Set 1

15Providing of concreting in 1:2:4 mix including muffing for erection of pole & Dist boxes panels including excavation of HR/SR as per approved drawing.

Package LS

16Providing & fixing of ' B ' Class ISI marked GI pipe of 25 mm inner diameter for cable looping, road crossing with necessary elbow / band to J. Box etc.

Package LS

17

Providing and fixing of GI clamp (25mm wide GI strip with 6 mm GI nut bolts) on structure at approx. 1/2 Mtr. Interval for clamping of cable . Clamp should be fix in such a way that cable can be easily mount inside it & sustain standing on structure. This also includes required other materials ,accessories required for complete functioning of Illumination system of whole project (switch yard and all buildings, structures) those are not covered in this schedule for Illumination. Please refer the drawing "General Schematic for Illumination" in the TS Illumination.

Package LS

Note: The qunatities of the ACP's mentioned in the schedule of requirement are based on std. requirement, which shall be finalised during detail engineering. The bidder has to assess the qty. of ACP's at the time of quoting the bid. The qty of ACP's finalised during detail engineering is binding to the bidder & no any extra payment shall be made. In all the case the decision of GETCO will be final.

G

Supply and installation of materials for Earthing system in allrespect as per respective specifications and special conditions(Successful bidder has to submit the complete design and BOQ forapproval)

1

Supply and Installation of earthing strips/round bars as shown below including digging of 600 mm depth and 450 mm wide trench fixing on structure as per std equipment earthing philosophy including fixing arrangement with two bolt arrangement, jointing, welding etc. complete.

of 45




a) 75 x 10 mm GI strip. RMt. 9000b) 50 x 6 mm GI strip. RMt. 9000c) 40 mm dia steel rod RMt. 20000d) 40mm dia 3mtr long steel rod Nos. 165e) 7/3.15 earth wire for earthing of towers with peak RMtr. 1500

2 Providing and installing Check pit as per drawing and instruction of Engineer In charge with provision of earth chamber. Nos. 6

3

Supply, Installation, Testing and Commissioning of maintenance free treated earth electrodes, as per attached drawing no. GETCO/E/P-021 (2 OF 2) R2 dated 04-06-15 and Technical specifications GETCO/E/TS-Maintenance free earth pits /R1 dated 04-06-15.

Nos. 70

4 Providing BB masonry inspection chamber (man hole) incl.light type CI cover as per GETCO drawing. Nos. 70

5 Design of earthgrid for whole switchyard using computer algorithmsfor modeling grounding systems as per Cl. 16.8 of IEEE-80. Package LS

6 Earthing Adequacy study for whole switchyard after commisioning earthmat in all respect (Scope as per annexure-E) Package LS

Note: Extra earth should be removed away from the site s/s premises or refilling earthing pits if required. All required materials for this job such as Copper Bonded Earthing Steel Rods, CI cover with frame,cement,sand, Ground Enhancement Material, gravel, bricks etc. to be supplied by the contractor.NOTE: Supply & Erection of 220/66KV Transformers are not in the scope of awardee, but awardee will erect the itmes other than the scope of transformer manufacturer and witness during the erection and testing of the same and provide all the result in as built drawings/documents.(II) PLCC PART

Sr NoDescription Unit of

Measurement Quantity

1 220kV ,4400PF CVT (having two windings with VA burden 50 & 50 and having accuracy of 0.2 & 3P class for metering and protection core respectively & simultaneous burden 100VA. Metering core shall be within seperate box having sealable compartment arrangement. Also with clamp/connectors & supporting structure. The interconnection from HF terminal of CVT to PLCC coupling device shall be made using 16 Sq.mm PVC insulated stranded (non flexible strands) copper cable.

No. 8

2 220kV, 0.5mH, 1250Amp Wave Trap with Blocking Band of, Band-(I)-100-160 & Band-(II) 150-500KHz and R min = 570 Ohm and pedestal mounting arrangement with three tie rod assembly including mounting pedestal assembly, support structure, BPI, clamp/connectors and require accessories.

No. 2

3 Modular coupling device MCD-80, Make: ABB (Set comprising of 1 No. of A9BS & 1 No. of A9BT) for Phase to Phase coupling arrangement for PLCC signal connectivity.

Set 1

4 Carrier Terminal Equipment with Dual 19” rack of 40Watt Single Channel, Fully Programmable Carrier Equipment Make suitable to operate on 220V DC and with 4-Wire table telephone for , Dummy Load Print , 75 Ohm Cylindrical Load and 4 Nos. of UHF Gland , Emergency jack handset as per technical Specification.

No. 2

of 45




5 Protection coupler with 2 coded & 2 uncoded command arrangement & perfectly match with above carrier terminal description of which given at Sr. No. 4 above.

No. 4

6 Supply & laying of 75 Ohm, unbalanced armoured co-axial cable for PLCC signal connectivity and providing UHF gland on both the ends of each main cable length to be laid for PLCC carrier room to bay gentry and loop cable for Ph to Ph coupling arrangement.

KM 2.5

7 FSK Data Modem Make: ABB & Type: NSK 5, Programmable for both Baud Rate (50 to 2400 Baud) and VFT Channel Centre Frequency and fully compatible with 40W fully programmable Carrier terminal description of which given at Sr. No. 4 above.

No. 1

8 FSK Data Modem with stand alone 19" rack with power supply module ,Make: ABB & Type: NSK 5, Programmable for both Baud Rate (50 to 2400 Baud) and VFT Channel Centre Frequency, suitable 220V DC to 48V DC converter and fully compatible with 40W fully programmable Carrier terminal description of which given at Sr. No. 4 above.

No. 1

9 PLCC Exchange of Make: MATRIX, Type Eternity 10S with 16 Nos. of Trunks & 16 Nos. of Subscribers suitable for both PLCC Dialling and Express Communication connectivity with Universal slot architecture having Hot stand by Power supply suitable to operate on 220V DC , Hot stand by CPU and with reputed make Push button type telephone instruments & digital key phone.

No. 1

11 DAS Meters network wiring complete up to RS 485 to RS 232 Convertor of DAS PC using Job

a) 3 core communication cable (as per specification given hereunder) Mtr. 100b) RS 485 to RS 232 Converter (as per specification given hereunder) No. 1

12 DAS PC with Printer (as per specification) No. 1(III) Protection Part

H

Supply, Erection, Testing and Commissioning of Protectionequipments and materials as per respective technical specificationsand relevant special conditions and suitable for One Main Bus andOne Main cum Transfer Bus system on 220kV side

1 Control & Protection panels for 220KV Bays ( Control Voltage - 220V DC ) as per tech specifications with following break up1) Control & Protection panel for Line Set 62) Control & Protection panel for Transformer with Differential Set 23) Control & Protection panel for BC cum TBC Set 1

6) Busbar Protection - (Central Unit - 24 bays, Peripheral Units - 09 Bays) [CU shall be mounted in one of the bay control & protection panel while PUs shall be mounted in respective bay control and protection panels as shown in panel GA drawing]

Set 1

2 GPS based Time Synchronising Unit (IEC 61850 compatible) Set 1

I

Supply, Erection, Testing and Commissioning of Protectionequipments and materials as per respective technical specificationsand relevant special conditions and suitable for Two Main Bussystem on 66kV side

of 45




Control & Protection Panel for 66kV bays ( Control Voltage - 220V DC ) as per tech specifications & with following break up1) Control & Protection Panel for two Lines Set 32) Control & Protection Panel for Transformer W/O Differential Relay (220/66KV TRF LV) & Buscoupler Bay Set 1

3) Control & Protection Panel for Transformer W/O Differential Relay (220/66KV TRF LV) & Line Set 1

4) Control & Protection Panel for Tranformer with Differential Relay (66/11KV Transformer) Set 1

5) Under Frequency Panel Set 1

J

Supply, Erection, Testing and Commissioning of General purposeequipments and materials as per respective technical specificationsand relevant special conditions and suitable for One Main and OneMain cum Transfer Bus system on 220kV, One main Bus system on132kV and Two Main Bus system on 66kV.

1

Battery set - 220 V, 250Ah at ECV -1.14, C5 Duly cycle {1.2 V, 180 cells, (174 For Battery set and 6 Spare) } Ni-CAD Battery Set (Equivalent to 266Ah as per C5 duty cycle at ECV - 1.0) with Two Step Two Tier FRP stand of adequate size.

No. 2

2

Battery Charger - 220 V (Float - 30A / Boost - 60A) - (SCADA compatible)Suitable to Ni-Cd Battery set and shall be able to charge Battery set as per requirement during float / boost mode as well as it shall supply to load as per rated voltage of load components.

No. 2

3 DCDB-220 V with 20 Feeder No. 44 DCDB-220 V with 20 Feeder (For PLCC Panels) No. 25 LTPB - (SCADA compatible) No. 2

KSupply, Installation, Testing and Commissioning of materials/itemfor Power Cable and Control Cable wiring including preparation ofwiring schedule.

1

Supply and Laying of 1.1 kV PVC armoured copper/Aluminum control/LTpower cable in trench including binding/clamping of cable with PVC locable wire tie as per requirement including supply and fixing ofidentification tags on both ends and at distance of every 100mtr. (Note :-Aluminium cables of size 185 mm2 & above shall be XLPE type)

1) 2c x 2.5 mm2, armoured copper control cable Mtr. 41002) 2c x 4 mm2 , armoured copper control cable Mtr. 18003) 4cx2.5 mm2, armoured copper control cable Mtr. 73004) 4c x 4 mm2 , armoured copper control cable Mtr. 76005) 7c x 2.5 mm2, armoured copper control cable Mtr. 22006) 12c x 2.5 mm2, armoured copper control cable Mtr. 58007) 12c x 4 mm2, armoured copper control cable Mtr. 43008) 19c x 2.5 mm2 , armoured copper control cable Mtr. 98009) 27c x 2.5 mm2 , armoured copper control cable Mtr. 430010A) 1 x 50 mm2 , armoured copper cable Mtr. 350010B) 4C x 10 mm2 , armoured copper control cable Mtr. 40011) 4 x 10 mm2 , Al. armoured LT cable Mtr. 400

of 45




12) 3.5 x 25 mm2 , Al. armoured LT cable Mtr. 290013) 3.5 x 50 mm2 , Al. armoured LT cable Mtr. 60014) 1C x 150 mm2 , Al. armoured LT cable Mtr. 4000Termination of the control cable at panel / MK box/equipment includingPVC binding dressing/shaping drilling of holes in panels for glands nuts forfollowing size. The work also includes Looping in panel and MK box withusing crimping type of lugs of suitable size with ferruling with proper sizeof copper cable wire. The loops should be bunched with using button tapeand proper shaping etc.1) cables from 2 core to 7 core of 2.5 & 4.0 Sq.mm size No. 11502) cables above 7 core No. 1300

Laying of 1.1kv PVC/XLPE armored Al. LT power cable in ground bydigging trench of suitable width and 450 mm depth with providing andfixing of brick and sand layer covering the cable in any type of soil andLaying of 1.1kv PVC armored copper control cable in heavy duty PVCpipe of suitable size buried in ground by digging trench of suitable widthand 450 mm depth in any type of soil including supply and fixing of Pipeand identification tags at distance of every 100 Mtrs for following size

1) Control Cables upto 7 core Mtr. 20502) Control Cables above 7 core and all LT cables Mtr. 2500

3a

Supply, Erection, Testing and Commissioning of Modular Variable-diameter Cable sealing system as per respective technical specificationand relevant special conditions wherever the electrical / instrumentation /communication / LT Power cable underground and over-ground enter orleave bay kiosks / control room of substations / cable trench / basement.

LS Package

Providing and fixing of 50mm dia 'B' class GI pipes with necessary size of band and couplings for control cable protection of CT, PT/CVT etc. equipments including fixing with structures as per instruction of Engineer-in-charge. 1) 220 KV Switch Yard Mtr. 2502) 66 KV switch Yard Mtr. 150Providing and fixing of 100mm dia 'B' class GI pipes with necessary size of band and couplings for control cable protection of CB, Isolator etc.equipments including fixing with structures as per instruction of Engineer-in-charge. 1) 220 KV Switch Yard Mtr. 2002) 66 KV switch Yard Mtr. 100

5 Providing and fixing bay MK as per tech spec No. 9

6 Providing and fixing Yard LT ACDB as per tech spec -with 20 OG feeders( 220KV & 66kV) No. 2

7 Providing and fixing Yard LT ACDB as per tech spec -with 12 OG feeders(132&66KV) No. 1

8

Providing and fixing of all weather proof, cold rolled sheet steel junctionbox for CVT & PT, CT terminations with 30 Nos. of disconnecting type,'Elmex' make CATDM 4 or equivalent type connectors and required no offuses, links etc.as per instruction of Engineer-in-charge.

1) PT JB No. 4

4

4a

2

3

of 45




2) CT JB No. 10Notes:- 1.# The quantities of control and power cables shown in theBOQ are based on typical cable philosophy. Hence, the contractorshall work out actual requirement of quantity for execution bycalculating cable lengths.2. All the cables shall be laid through minimum possible route and accordingly the quantity of cables shall be calculated and considered as per actual measurement. Any adjustment found during execution is to be absorbed and final amendment of quantity shall be based on approved 'As Built' quantity.

(IV) SCADA Part 220kV MOTIGOP Substation (220kV & 66kV system)



L

Supply, Erection, Testing and Commissioning of SCADA equipments and materials as per respective technical specifications and relevant special conditions and suitable for One Main and One Main cum Transfer Bus system on 220kV side, and Two Main Bus system on 66kV side

1 Bay Control Unit / RTU for Substation Auxiliaries # Nos 12 Bay Control Unit for Protection Coupler of PLCC / FOTE ** Nos 13 HMI Server computer with required softwares Nos 24 DR workstation PC No. 15 Gateway for remote control with software No 16 Gateway for RTU Data with software No 17 SCADA software (For local and Remote control centre) No 18 Ethernet Fiber Switches* Nos 99 Line Interface unit - 2 Cable entry, 12 ports Nos 16

10 Line Interface unit - 8 Cable entry, 32 ports Nos 111 Laser Jet colour Printer Nos 112 Laser Jet Printer Nos 1

133 KVA UPS with Battery having Auto changeover scheme for seamless changeover (Battery - 12V SMF Battery set, Ah rating and Nos.shall be suitable for 2 hours back-up as per UPS DC Voltage rating)

Nos 2

15 Armoured Fibre Optic Cable with HDPE duct (Mutli mode) MTR. 200016 Yard Kiosk for 220KV Switchyard

Internal Dimensions - 4000 (L) X 3500 (W) X 3300 (H) mm Nos 4Internal Dimensions - 5000 (L) X 3500 (W) X 3300 (H) mm Nos 1

18 Yard Kiosk for 66KV SwitchyardInternal Dimensions - 5000 (L) X 3500 (W) X 3300 (H) mm 2

19 Panel for mounting SCADA equipments Nos 120 Panel for mounting PLCC / FOTE BCU Nos 121 Panel for mounting Station Auxiliaries BCU/RTU Nos 122 Furniture for SCADA equipments Set 123 Panel for Mounting Spares Nos 124 Spares for SCADA and Protection 1 Bay Control Unit Nos 12 Bay Control and Protection Unit Nos 13 Line Interface Unit - 8 Cable entry, 32 ports Nos 14 Ethernet fiber switch Nos 1

of 45




5 Busbar Protection Peripheral Unit Nos 1Note: 1) Any material/equipment accessories which are not listed in BOQ or scope of supply but required to complete the job shall be included and shown in technical bid.2)*Ethernet switches shall have as many spare ports as utilized ports. 3) ** PLCC / FOTE BCU shall have sufficient I/Os as per given listconsidering future lines also. 4) # BCU for station Auxiliary shall have sufficient I/Os as per list orotherwise suitable RTU shall be provided.5) Contractor shall be responsible for necessary co-ordination with FOTEand OPGW supplier & erection agency to establish remote connectivityand over all operation from Master Control Centre through SCADAsystem.(V) SCADA Part for 220KV Nyara S/S for remote operation

MSupply, Erection, Testing and Commissioning of SCADA equipments and materials as per respective technical specifications and relevant special conditions.

1 HMI Server computer with required softwares Nos 22 DR workstation PC Nos 13 Ethernet Fiber Switch* Nos 24 Laser Jet colour Printer Nos 15 Laser Jet Printer Nos 1

6


Nos 2

7 Panel for mounting SCADA equipments Nos 18 Furniture for SCADA equipments Set 1

Note: 1) Any material/equipment accessories which are not listed in BOQ or scope of supply but required to complete the job shall be included and shown in technical bid.2)*Ethernet switches shall have as many spare ports as utilized ports. 3) Contractor shall be responsible for necessary co-ordination with FOTEand OPGW supplier & erection agency to establish remote connectivityand over all operation from Master Control Centre through SCADAsystem.

PART - B Erection, Testing & Commissioning Part

(I) SWITCHYARD PART

ASupply and Erection of 220kV Equipments (as per respective technical specifications and relevant special conditions) suitable for One Main Bus and One Main cum Transfer Bus scheme

1 Surge Arrester 198kV, 10kA, Cl-3 with structure and clamp connectors as per Technical spec

No. 24

2PT 220kV/√3-/110V/√3-3C with structure and clamp connectors as per Technical spec No. 6

3 BPI 8kN with structure and clamp connectors as per Technical spec No. 157

4 HBPI 8kN with structure and clamp connectors as per Technical spec No. 39

of 45




5HDB Isolator with one ES 1600A 40kA 3s with structure and clamp connectors as per Technical spec Set. 8

6HDB Isolator without ES 1600A 40kA 3s with structure and clamp connectors as per Technical spec Set. 19

7 Tandem DB Isolator 1600A 40kA 3s with structure and clamp connectors as per Technical spec Set. 9

8CT conventional 1500-1200-600/1, 5C with structure and clamp connectors as per Technical spec No. 27

9CB 2000A 40kA 3s with structure and clamp connectors as per Technical spec Set. 9

BSupply and Erection of 220kV Switchyard material (as per respective technical specifications and relevant special conditions) suitable for One Main Bus and One Main cum Transfer Bus scheme

1 Gantry structures GI as per BOM, Steel & A/B part MT 123.1

2 Gantry structures GI as per BOM, Bolt nut part MT 5.4

3VHF Tower Mast Structure GI with stub, template complete as per BOM, Steel & A/B part MT 1.65

4VHF Tower Mast structures GI with stub, template complete as per BOM, Bolt nut part MT 0.1

5

Stringing of bus with Twin AL59(61/3.50) conductor for all the three phases with required Silicon Rubber Insulators, hardwares & accessories, spacers provided at every 3.0 mtr. interval etc. complete as per relevant standards and approved drawings with Jumpers for continuous Bus Arrangement (It includes cost of Conductor, Silicon Rubber Insulators, hardwares & accessories, spacers etc.all items required for satisfactory functioning. Any variation in quantities shall be absorbed by contractor.

a Main Bus with 36Mtr span including bus jumpers No. of Span 12

b Line flyover bus with 57Mtr span No. of Bay 8

c Transformer flyover bus with 57Mtr span No. of Bay 3

d Bus Coupler Flyover Bus with 57 Mtr. Span No. of Bay 1

6

Stringing of Earth Wire with 7/3.15 GS wire with required hardwares & accessories etc. complete as per standards and approved drawings for span of 57 meters.(It includes cost of Earthwire,hardwares & accessories, etc. all items required for satisfactory functioning. Any variation in quantities shall be absorbed by contractor

Span 13

7

Droppers (including required suspension string with hardware & accessories if any) & Jumpers (including Equipment to Equipment) with Twin AL59(61/3.50) conductor as per standards and approved drawings with provision of required spacers( Suitable for 350mm spacing) at every 3.0 mtr. interval .(It includes cost of Conductor,Silicon Rubber Insulators, hardwares & accessories, Fire Wedge connectors, spacers etc.all items required for satisfactory functioning. Any variation in quantities shall be absorbed by contractor)

of 45




a 220/66KV Transformer Bay No. of bay 2

b 220KV Line Bay No. of bay 6

c 220KV Bus Coupler Bay No. of bay 1

8

Droppers (including required suspension string with hardware & accessories if any) & Jumpers with Single AL59(61/3.50) conductor as per standards and approved drawings (It includes cost of Conductor,Silicon Rubber Insulators, hardwares & accessories, Fire Wedge Connectors, etc.all items required for satisfactory functioning. Any variation in quantities shall be absorbed by contractor)

a 220KV Line Bay - LA & CVT No. of bay 6

b 220/66KV Transformer Bay - LA No. of bay 2

c 220KV PT Bay No. of bay 2

CSupply and Erection of 66kV Equipments (as per respective technical specifications and relevant special conditions) suitable for Two Main Bus scheme

1 Power Transformer 66/11kV, 5 MVA with oil and accessories connector suitable for Single AL59(61/3.50)

No. 1

2Surge Arrester 60kV, 10KA, Class 3 with structure and clamp connectors suitable for Single AL59(61/3.50) No. 27

3PT 66kV/v3-/110V/v3-2C with structure and clamp connectors suitable for Single AL59(61/3.50) No. 6

4BPI 4kN with structure and clamp connectors suitable for Single AL59(61/3.50) No. 56

5BPI 4kN with structure and clamp connectors suitable for Twin AL59(61/3.50) No. 28

6HBPI 4kN with structure and clamp connectors suitable for Twin AL59(61/3.50) No. 6

7HDB Isolator with one ES 1250A 25kA 3s with structure and clamp connectors suitable for Single AL59(61/3.50) Set. 6

8HDB Isolator without ES 1250A 25kA 3s with structure and clamp connectors suitable for Single AL59(61/3.50) Set. 15

9HDB Isolator without ES 1250A 25kA 3s with structure and clamp connectors suitable for Single AL59(61/3.50) (3nos./set) & Twin AL59(61/3.50) (3nos./set)

Set. 2

10HDB Isolator without ES 2000A 25kA 3s with structure and clamp connectors suitable for Twin AL59(61/3.50) Set. 6

11 CT 600-300/1 3C, 31.5KA 3S with structure and clamp connectors suitable for Single AL59(61/3.50) No. 18

12CT 1600-1200/1 3C 31.5KA 3S with structure and clamp connectors suitable for Twin AL59(61/3.50) No. 9

of 45




13CT 100-50/1 3C 31.5KA 3S with structure and clamp connectors suitable for Single AL59(61/3.50) No. 3

14CB 1600A 25kA 3S with structure and clamp connectors suitable for Single AL59(61/3.50) Set. 7

15 CB 1600A 25kA 3S with structure and clamp connectors suitable for Twin AL59(61/3.50) Set. 3

DSupply and Erection of 66kV Switchyard Materials (as per respective technical specifications and relevant special conditions) suitable for Two Main Bus scheme

1 Gantry structures GI as per BOM , Steel & A/B part MT 43.7

2 Gantry structures GI as per BOM , Bolt nut part MT 5.2

3

Stringing of bus for all the three phases with Twin AL59(61/3.50) conductor, Silicon Rubber Insulators hardwares, spacers(suitable for 350mm spacing) at interval of 4.0 mtr complete as per relevant standards and approved drawings.(The scope includes the cost of Silicon Rubber Insulators, hardwares, accessories, spacers etc.all items required for satisfactory operation. Any variation in quantities shall be absorbed by erection contractor.

a Main Bus with 33.800 Mtr. Span including bus jumpers Span 2

b Main Bus with 33.950 Mtr. Span including bus jumpers Span 4

c Transformer flyover bus with 54.7Mtr. Span No. of bay 2

d Transformer flyover bus with 16.4 Mtr. Span No. of bay 2

4

Stringing of bus for all the three phases with Single AL59(61/3.50) conductor, Silicon Rubber Insulators hardwares as per relevant standards and approved drawings.(The scope includes the cost of Silicon Rubber Insulators, hardwares, accessories, spacers etc.all items required for satisfactory operation. Any variation in quantities shall be absorbed by erection contractor.

a Line flyover bus with 23.8 Mtr. Span No. of bay 8

b 66/11KV Trf. flyover bus with 23.8 Mtr. Span No. of bay 1

5

Stringing of Earth Wire with 7/3.15 GS wire with required hardwares & accessories etc. complete as per standards and approved drawings for the shown span. (It includes cost of hardwares & accessories etc. all items for satisfactory functioning. Any variation in quantities should be absorbed by erection contractor.

a Main Bus with 33.950 Mtr. Span Span 2

b Other Requirements with

22.7 Mtr. Span Span 116.1 Mtr. Span Span 1

c Line flyover bus with 23.8 Mtr. Span No. of bay 7

d 66/11KV Trf. flyover bus with 23.8 Mtr. Span No. of bay 1

e Transformer flyover bus with 54.7 Mtr. Span No. of bay 4

of 45




f Transformer flyover bus with 16.4 Mtr. Span No. of bay 4

6

Droppers (including required suspension string with hardware & accessories if any) & Jumpers with Single AL59(61/3.50) conductor as per standards and approved drawings. (It includes cost of Silicon Rubber Insulators, Fire wedge connectors,hardwares & accessories etc. all items required for satisfactory functioning. Any variation in quantities shall be absorbed by erection contractor)

a 220/66KV Transformer Bay - LA No. of bay 2

b 66KV PT Bay No. of bay 2

c 66KV Line Bay No. of bay 6

d 66/11KV Transformer Bay No. of bay 1

7

Droppers and Jumpering (equipment to equipment) with Twin AL59(61/3.50) conductor as per standards and approved drawings with provision of spacers suitable for 350mm spacing at 4.0 mtr interval. (The scope includes the cost of accessories ,spacers, fire wedge connectors etc.all items required for satisfactory operation.

a 220/66KV Transformer Bay (66KV side) No. of bay 2

b 66KV Bus Coupler Bay No. of bay 1

ESupply and Erection of General purpose equipments and materials as per respective technical specifications and relevant special conditions.

1

Suitable arrangement of 11KV connection (A) from 5 MVA station TR to one no. of 11kV/415V, 500 kVA distribution transformer which comprises of: 1) 22 kV outdoor CT having ratio 300-150/1-1-0.577A, STC: 25 kA – 3 sec, BIL 55/150 kVp.2) 22 kV outdoor VCB, 1250A, STC: 25 kA – 3 sec, BIL 55/150 kVp.3) 22 kV outdoor Isolator, 630A, STC: 25 kA – 3 sec.4) 9 KV LAwith support structure, insulated conductor and DP structure with DO fuse, 22kV BPIs arrangement including Dist box suitable to dist transformer. and (B) from separate 11 KV express feeder (feeder termination shall be arranged by GETCO) to another 11kV/415V, 500 kVA distribution transformer which comprises of:1) 22 kV outdoor Isolator, 630A, STC: 25 kA – 3 sec.2) 9 KV LAwith support structure, insulated conductor and DP structure with DO fuse, 22kV BPIs arrangement including Dist box suitable to dist transformer. (11KV Power Cable shall be supplied by GETCO, however Laying of cable with termination kit supply and installation is in the scope of bidder)

Package LS

of 45




2 AC unit 3 Ton Split (Reputed make) No. 5

3 AC unit 1.5 Ton Split (5 star rating and reputed make) No. 2

4

Distribution Transformer 11kV/415V,500 kVA with suitable Dist. Box and its fixing -mounting arrangement as per drg. No. GETCO/E/2S-STD/P-031/LTD R0,Dtd. 11-03-15. Required LT Distribution boxes with LT cable and changeover switch supply is in the scope of bidder.

No 2

F

Supply and installation of materials for Illumination system in allrespect as per respective specifications and special conditions (Sucessful bidder has to submit the complete design and BOQ forapproval)

1

Providing & Fixing of Energy Efficient LED type (Techhnical spec Cl No. 2.10.4.8-I LED 3 type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs.as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point,Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp , DC Plug etc all items as per Ann-4 in following rooms (with safety device ELCB)

i Control Room Package LS

ii PLCC Room Package LS

iii Office Package LS

2

Providing & Fixing of Energy Efficient LED Type (Techhnical spec Cl No. 2.10.4.8-I LED 1 or I LED 2 type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs.as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point, Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp , DC Plug etc all items as per Ann-4 in following rooms (with safety device ELCB)

i Battery Room Package LS

ii LV Room Package LS

iii Store Room Package LS

iv Ramp Slope Package LS

v Veranda Package LS

vi Toilet Gents Package LS

vii WC Package LS

viii Toilet Ladies Package LS

ix Passage (Corridor) Package LS

x Water Room Package LS

xi Security Cabin Package LS

of 45




3

Providing & Fixing of Energy Efficient LED Type (Techhnical spec Cl No. 2.10.4.8-I LED 1 or I LED 2 type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs.as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point, Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp , DC Plug etc all items as per Ann-4 in following room.

i Store building Package LS

4

Providing & Fixing of Energy Efficient Indoor 2x36 Tube light for Quaters (4 Nos.) in all the rooms, passages complete (ref. Ann-4) as per technical spec with required casing caping point wiring as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan,with requisite MCBs and as per Ann-4 in following amenities

1 Drawing room of Type IV Qtr Package LS

2 Bedroom 1of Type IV Qtr Package LS

3 Bedroom 2 of Type IV Qtr Package LS

5

Providing & Fixing of Energy Efficient Indoor luminaries in all the rooms, passages Qtr (4 Nos.) complete (ref. Ann-4 as per technical spec Cl No. 2.10.4.8 (CFL type) with required casing caping point wiring as per technical spec. Scope also includes providing and fixing of 15/5 A plug, as per Ann-4 in following rooms--- With supply and fixing of 3 KW Geyser (Instant type Sphere hot make ) Arrangement in bathroom or attached toilet blocks

1 Passage for Type IV Qtr Package LS

2 Toilet common for Type IV Qtr Package LS

3 Toilet attached to Room No1 for Type IV Qtr Package LS

4 Kitchen for Type IV Qtr Package LS

5 Store for Type IV Qtr Package LS

6

Providing and fixing of flood light luminaries as per design for whole switch yard area ( 220 & 66kV) with Energy Efficient LED type (Techhnical spec Cl No. 2.10.4.8-I LED 5 Type) Outdoor luminaries as per design calculation, with respect to required lux level & relevant tender drgs., and required industrial grade point wiring as per technical spec.& ancillaries and suitable for mounting on structure at appropriate height as per specifications TS illuminations cl. no 2.10.4.8 with necessary GI fabrication & GI bolt nuts to fix control gear box at the structure with complete internal and external wiring to J. box ,Dist panel/section feeder pillar etc with supply of required 3 c x 2.5 mm2 copper armoured cable (as per spec ) .The scope includes supply and erection of all the materials required for satisfactory functioning of above work.

Package LS

of 45




7

Providing and installation of Energy efficient LED type post top lantern for main gate and road from main gate to switchyard via control room as per design with Philips/CGL/Bajaj/GE/Oshram make & ancillaries suitable for mounting on Gate pillars and 4.5 mtr poles with necessary GI fabrication & GI bolt nuts to fix control gear box with complete internal and external wiring to J.box,Dist panel/section feeder pillar, fixing terminal etc. with supply of required 3 c x 2.5 mm2 copper armoured cable as per spec .This also includes the supply and erection of required 4.5 mtr poles and its foundation work as per spec and earthing with main mesh. The scope includes supply and erection of all the materials required for satisfactory functioning of above work.

Package LS

8

Providing and fixing of street light luminaries for reamaining area (like road, near whole compound wall/fencing area etc.) of switch yard complete as per design with Philips/CGL/Bajaj/GE/Oshram or Similar make LED lamp & ancillaries suitable for mounting on 7.0 mtr swaged poles as per spec.TS illuminations cl. no 2.10.4.8 (S-LED) at appropriate height with necessary GI fabrication & GI bolt nuts to fix control gear box with complete internal and external wiring to J. box ,dist panel/section feeder pillar, fixing terminal etc with supply of required 3 c x 2.5 mm2 copper armoured cable (as per spec). This also includes the supply and erection of 7.0 mtr swaged pole and foundation work as per spec. and panting with two coats of primer and two priming of zinc chromate as well as earthing with main mesh. The scope includes supply and erection of all the materials required for satisfactory functioning of above work.

Package LS

9

Supply and Erection of main lighting Panel ACP-1 as per Specifications. Set comprises minimum 3 nos.of such panels qty may be more if required as per design.Scope also includes the providing and erection of cable size (as per design requirement) and 25x6 GI strip for earthing with main mesh

Set 1

10


Set 1

11


Set 1

12


Set 1

13

Supply and Erection of main Yard light Dist. Board as per designed capacity ratings.Scope also includes the providing and erection of cable size (as per design requirement) and 50x6 GI strip for earthing with main mesh

Nos 2

of 45




14

Supply and Erection of Lighting Transformers as per designed capacity.Scope also includes the providing and erection of cable size ( as per design requirement) and 50x6 GI strip for earthing with main mesh. Please refer the drawing "General Schematic for Illumination" in the TS Illumination.

Set 1

15Providing of concreting in 1:2:4 mix including muffing for erection of pole & Dist boxes panels including excavation of HR/SR as per approved drawing.

Package LS

16Providing & fixing of ' B ' Class ISI marked GI pipe of 25 mm inner diameter for cable looping, road crossing with necessary elbow / band to J. Box etc.

Package LS

17

Providing and fixing of GI clamp (25mm wide GI strip with 6 mm GI nut bolts) on structure at approx. 1/2 Mtr. Interval for clamping of cable . Clamp should be fix in such a way that cable can be easily mount inside it & sustain standing on structure. This also includes required other materials ,accessories required for complete functioning of Illumination system of whole project (switch yard and all buildings, structures) those are not covered in this schedule for Illumination. Please refer the drawing "General Schematic for Illumination" in the TS Illumination.

Package LS

Note: The qunatities of the ACP's mentioned in the schedule of requirement are based on std. requirement, which shall be finalised during detail engineering. The bidder has to assess the qty. of ACP's at the time of quoting the bid. The qty of ACP's finalised during detail engineering is binding to the bidder & no any extra payment shall be made. In all the case the decision of GETCO will be final.

G

Supply and installation of materials for Earthing system in allrespect as per respective specifications and special conditions(Successful bidder has to submit the complete design and BOQ forapproval)

1

Supply and Installation of earthing strips/round bars as shown below including digging of 600 mm depth and 450 mm wide trench fixing on structure as per std equipment earthing philosophy including fixing arrangement with two bolt arrangement, jointing, welding etc. complete.

a) 75 x 10 mm GI strip. RMt. 9000b) 50 x 6 mm GI strip. RMt. 9000c) 40 mm dia steel rod RMt. 20000d) 40mm dia 3mtr long steel rod Nos. 165e) 7/3.15 earth wire for earthing of towers with peak RMtr. 1500

2 Providing and installing Check pit as per drawing and instruction of Engineer In charge with provision of earth chamber. Nos. 6

3

Supply, Installation, Testing and Commissioning of maintenance free treated earth electrodes, as per attached drawing no. GETCO/E/P-021 (2 OF 2) R2 dated 04-06-15 and Technical specifications GETCO/E/TS-Maintenance free earth pits /R1 dated 04-06-15.

Nos. 70

4 Providing BB masonry inspection chamber (man hole) incl.light type CI cover as per GETCO drawing. Nos. 70

of 45




5 Design of earthgrid for whole switchyard using computer algorithmsfor modeling grounding systems as per Cl. 16.8 of IEEE-80. Package LS

6 Earthing Adequacy study for whole switchyard after commisioning earthmat in all respect (Scope as per annexure-E) Package LS

Note: Extra earth should be removed away from the site s/s premises or refilling earthing pits if required. All required materials for this job such as Copper Bonded Earthing Steel Rods, CI cover with frame,cement,sand, Ground Enhancement Material, gravel, bricks etc. to be supplied by the contractor.NOTE: Supply & Erection of 220/66KV Transformers are not in the scope of awardee, but awardee will erect the itmes other than the scope of transformer manufacturer and witness during the erection and testing of the same and provide all the result in as built drawings/documents.(II) PLCC PART



1 220kV ,4400PF CVT (having two windings with VA burden 50 & 50 and having accuracy of 0.2 & 3P class for metering and protection core respectively & simultaneous burden 100VA. Metering core shall be within seperate box having sealable compartment arrangement. Also with clamp/connectors & supporting structure. The interconnection from HF terminal of CVT to PLCC coupling device shall be made using 16 Sq.mm PVC insulated stranded (non flexible strands) copper cable.

No. 8

2 220kV, 0.5mH, 1250Amp Wave Trap with Blocking Band of, Band-(I)-100-160 & Band-(II) 150-500KHz and R min = 570 Ohm and pedestal mounting arrangement with three tie rod assembly including mounting pedestal assembly, support structure, BPI, clamp/connectors and require accessories.

No. 2

3 Modular coupling device MCD-80, Make: ABB (Set comprising of 1 No. of A9BS & 1 No. of A9BT) for Phase to Phase coupling arrangement for PLCC signal connectivity.

Set 1

4 Carrier Terminal Equipment with Dual 19” rack of 40Watt Single Channel, Fully Programmable Carrier Equipment Make suitable to operate on 220V DC and with 4-Wire table telephone for , Dummy Load Print , 75 Ohm Cylindrical Load and 4 Nos. of UHF Gland , Emergency jack handset as per technical Specification.

No. 2

5 Protection coupler with 2 coded & 2 uncoded command arrangement & perfectly match with above carrier terminal description of which given at Sr. No. 4 above.

No. 4

6 Supply & laying of 75 Ohm, unbalanced armoured co-axial cable for PLCC signal connectivity and providing UHF gland on both the ends of each main cable length to be laid for PLCC carrier room to bay gentry and loop cable for Ph to Ph coupling arrangement.

KM 2.5

7 FSK Data Modem Make: ABB & Type: NSK 5, Programmable for both Baud Rate (50 to 2400 Baud) and VFT Channel Centre Frequency and fully compatible with 40W fully programmable Carrier terminal description of which given at Sr. No. 4 above.

No. 1

of 45




8 FSK Data Modem with stand alone 19" rack with power supply module ,Make: ABB & Type: NSK 5, Programmable for both Baud Rate (50 to 2400 Baud) and VFT Channel Centre Frequency, suitable 220V DC to 48V DC converter and fully compatible with 40W fully programmable Carrier terminal description of which given at Sr. No. 4 above.

No. 1

9 PLCC Exchange of Make: MATRIX, Type Eternity 10S with 16 Nos. of Trunks & 16 Nos. of Subscribers suitable for both PLCC Dialling and Express Communication connectivity with Universal slot architecture having Hot stand by Power supply suitable to operate on 220V DC , Hot stand by CPU and with reputed make Push button type telephone instruments & digital key phone.

No. 1

11 DAS Meters network wiring complete up to RS 485 to RS 232 Convertor of DAS PC using Job

a) 3 core communication cable (as per specification given hereunder) Mtr. 100b) RS 485 to RS 232 Converter (as per specification given hereunder) No. 1

12 DAS PC with Printer (as per specification) No. 1(III) Protection Part

H

Supply, Erection, Testing and Commissioning of Protectionequipments and materials as per respective technical specificationsand relevant special conditions and suitable for One Main Bus andOne Main cum Transfer Bus system on 220kV side

1 Control & Protection panels for 220KV Bays ( Control Voltage - 220V DC ) as per tech specifications with following break up1) Control & Protection panel for Line Set 62) Control & Protection panel for Transformer with Differential Set 23) Control & Protection panel for BC cum TBC Set 1

6) Busbar Protection - (Central Unit - 24 bays, Peripheral Units - 09 Bays) [CU shall be mounted in one of the bay control & protection panel while PUs shall be mounted in respective bay control and protection panels as shown in panel GA drawing]

Set 1

2 GPS based Time Synchronising Unit (IEC 61850 compatible) Set 1

I

Supply, Erection, Testing and Commissioning of Protectionequipments and materials as per respective technical specificationsand relevant special conditions and suitable for Two Main Bussystem on 66kV sideControl & Protection Panel for 66kV bays ( Control Voltage - 220V DC ) as per tech specifications & with following break up1) Control & Protection Panel for two Lines Set 32) Control & Protection Panel for Transformer W/O Differential Relay (220/66KV TRF LV) & Buscoupler Bay Set 1

3) Control & Protection Panel for Transformer W/O Differential Relay (220/66KV TRF LV) & Line Set 1

4) Control & Protection Panel for Tranformer with Differential Relay (66/11KV Transformer) Set 1

5) Under Frequency Panel Set 1

of 45




J

Supply, Erection, Testing and Commissioning of General purposeequipments and materials as per respective technical specificationsand relevant special conditions and suitable for One Main and OneMain cum Transfer Bus system on 220kV, One main Bus system on132kV and Two Main Bus system on 66kV.

1

Battery set - 220 V, 250Ah at ECV -1.14, C5 Duly cycle {1.2 V, 180 cells, (174 For Battery set and 6 Spare) } Ni-CAD Battery Set (Equivalent to 266Ah as per C5 duty cycle at ECV - 1.0) with Two Step Two Tier FRP stand of adequate size.

No. 2

2

Battery Charger - 220 V (Float - 30A / Boost - 60A) - (SCADA compatible)Suitable to Ni-Cd Battery set and shall be able to charge Battery set as per requirement during float / boost mode as well as it shall supply to load as per rated voltage of load components.

No. 2

3 DCDB-220 V with 20 Feeder No. 44 DCDB-220 V with 20 Feeder (For PLCC Panels) No. 25 LTPB - (SCADA compatible) No. 2

KSupply, Installation, Testing and Commissioning of materials/itemfor Power Cable and Control Cable wiring including preparation ofwiring schedule.

1

Supply and Laying of 1.1 kV PVC armoured copper/Aluminum control/LTpower cable in trench including binding/clamping of cable with PVC locable wire tie as per requirement including supply and fixing ofidentification tags on both ends and at distance of every 100mtr. (Note :-Aluminium cables of size 185 mm2 & above shall be XLPE type)

1) 2c x 2.5 mm2, armoured copper control cable Mtr. 41002) 2c x 4 mm2 , armoured copper control cable Mtr. 18003) 4cx2.5 mm2, armoured copper control cable Mtr. 73004) 4c x 4 mm2 , armoured copper control cable Mtr. 76005) 7c x 2.5 mm2, armoured copper control cable Mtr. 22006) 12c x 2.5 mm2, armoured copper control cable Mtr. 58007) 12c x 4 mm2, armoured copper control cable Mtr. 43008) 19c x 2.5 mm2 , armoured copper control cable Mtr. 98009) 27c x 2.5 mm2 , armoured copper control cable Mtr. 430010A) 1 x 50 mm2 , armoured copper cable Mtr. 350010B) 4C x 10 mm2 , armoured copper control cable Mtr. 40011) 4 x 10 mm2 , Al. armoured LT cable Mtr. 40012) 3.5 x 25 mm2 , Al. armoured LT cable Mtr. 290013) 3.5 x 50 mm2 , Al. armoured LT cable Mtr. 60014) 1C x 150 mm2 , Al. armoured LT cable Mtr. 4000Termination of the control cable at panel / MK box/equipment includingPVC binding dressing/shaping drilling of holes in panels for glands nuts forfollowing size. The work also includes Looping in panel and MK box withusing crimping type of lugs of suitable size with ferruling with proper sizeof copper cable wire. The loops should be bunched with using button tapeand proper shaping etc.1) cables from 2 core to 7 core of 2.5 & 4.0 Sq.mm size No. 1150

2

of 45




2) cables above 7 core No. 1300

Laying of 1.1kv PVC/XLPE armored Al. LT power cable in ground bydigging trench of suitable width and 450 mm depth with providing andfixing of brick and sand layer covering the cable in any type of soil andLaying of 1.1kv PVC armored copper control cable in heavy duty PVCpipe of suitable size buried in ground by digging trench of suitable widthand 450 mm depth in any type of soil including supply and fixing of Pipeand identification tags at distance of every 100 Mtrs for following size

1) Control Cables upto 7 core Mtr. 20502) Control Cables above 7 core and all LT cables Mtr. 2500

3a

Supply, Erection, Testing and Commissioning of Modular Variable-diameter Cable sealing system as per respective technical specificationand relevant special conditions wherever the electrical / instrumentation /communication / LT Power cable underground and over-ground enter orleave bay kiosks / control room of substations / cable trench / basement.

LS Package

Providing and fixing of 50mm dia 'B' class GI pipes with necessary size of band and couplings for control cable protection of CT, PT/CVT etc. equipments including fixing with structures as per instruction of Engineer-in-charge. 1) 220 KV Switch Yard Mtr. 2502) 66 KV switch Yard Mtr. 150Providing and fixing of 100mm dia 'B' class GI pipes with necessary size of band and couplings for control cable protection of CB, Isolator etc.equipments including fixing with structures as per instruction of Engineer-in-charge. 1) 220 KV Switch Yard Mtr. 2002) 66 KV switch Yard Mtr. 100

5 Providing and fixing bay MK as per tech spec No. 9

6 Providing and fixing Yard LT ACDB as per tech spec -with 20 OG feeders( 220KV & 66kV) No. 2

7 Providing and fixing Yard LT ACDB as per tech spec -with 12 OG feeders(132&66KV) No. 1

8

Providing and fixing of all weather proof, cold rolled sheet steel junctionbox for CVT & PT, CT terminations with 30 Nos. of disconnecting type,'Elmex' make CATDM 4 or equivalent type connectors and required no offuses, links etc.as per instruction of Engineer-in-charge.

1) PT JB No. 42) CT JB No. 10Notes:- 1.# The quantities of control and power cables shown in theBOQ are based on typical cable philosophy. Hence, the contractorshall work out actual requirement of quantity for execution bycalculating cable lengths.2. All the cables shall be laid through minimum possible route and accordingly the quantity of cables shall be calculated and considered as per actual measurement. Any adjustment found during execution is to be absorbed and final amendment of quantity shall be based on approved 'As Built' quantity.

3

4

4a

of 45




(IV) SCADA Part 220kV MOTIGOP Substation (220kV & 66kV system)



L

Supply, Erection, Testing and Commissioning of SCADA equipments and materials as per respective technical specifications and relevant special conditions and suitable for One Main and One Main cum Transfer Bus system on 220kV side, and Two Main Bus system on 66kV side

1 Bay Control Unit / RTU for Substation Auxiliaries # Nos 12 Bay Control Unit for Protection Coupler of PLCC / FOTE ** Nos 13 HMI Server computer with required softwares Nos 24 DR workstation PC No. 15 Gateway for remote control with software No 16 Gateway for RTU Data with software No 17 SCADA software (For local and Remote control centre) No 18 Ethernet Fiber Switches* Nos 99 Line Interface unit - 2 Cable entry, 12 ports Nos 16

10 Line Interface unit - 8 Cable entry, 32 ports Nos 111 Laser Jet colour Printer Nos 112 Laser Jet Printer Nos 1


Nos 2

15 Armoured Fibre Optic Cable with HDPE duct (Mutli mode) MTR. 200016 Yard Kiosk for 220KV Switchyard

Internal Dimensions - 4000 (L) X 3500 (W) X 3300 (H) mm Nos 4Internal Dimensions - 5000 (L) X 3500 (W) X 3300 (H) mm Nos 1

18 Yard Kiosk for 66KV SwitchyardInternal Dimensions - 5000 (L) X 3500 (W) X 3300 (H) mm 2

19 Panel for mounting SCADA equipments Nos 120 Panel for mounting PLCC / FOTE BCU Nos 121 Panel for mounting Station Auxiliaries BCU/RTU Nos 122 Furniture for SCADA equipments Set 123 Panel for Mounting Spares Nos 124 Spares for SCADA and Protection 1 Bay Control Unit Nos 12 Bay Control and Protection Unit Nos 13 Line Interface Unit - 8 Cable entry, 32 ports Nos 14 Ethernet fiber switch Nos 15 Busbar Protection Peripheral Unit Nos 1

Note: 1) Any material/equipment accessories which are not listed in BOQ or scope of supply but required to complete the job shall be included and shown in technical bid.2)*Ethernet switches shall have as many spare ports as utilized ports. 3) ** PLCC / FOTE BCU shall have sufficient I/Os as per given listconsidering future lines also.

of 45




4) # BCU for station Auxiliary shall have sufficient I/Os as per list orotherwise suitable RTU shall be provided.5) Contractor shall be responsible for necessary co-ordination with FOTEand OPGW supplier & erection agency to establish remote connectivityand over all operation from Master Control Centre through SCADAsystem.(V) SCADA Part for 220KV Nyara S/S for remote operation

MSupply, Erection, Testing and Commissioning of SCADA equipments and materials as per respective technical specifications and relevant special conditions.

1 HMI Server computer with required softwares Nos 22 DR workstation PC Nos 13 Ethernet Fiber Switch* Nos 24 Laser Jet colour Printer Nos 15 Laser Jet Printer Nos 1

6


Nos 2

7 Panel for mounting SCADA equipments Nos 18 Furniture for SCADA equipments Set 1

Note: 1) Any material/equipment accessories which are not listed in BOQ or scope of supply but required to complete the job shall be included and shown in technical bid.2)*Ethernet switches shall have as many spare ports as utilized ports. 3) Contractor shall be responsible for necessary co-ordination with FOTEand OPGW supplier & erection agency to establish remote connectivityand over all operation from Master Control Centre through SCADAsystem.(VI) Civil Part

SR. NO. DESCRIPTION UNIT QTY.

1 Excavation for foundation in trenches up to 1.5m depth includingsorting out and stacking of useful materials and disposing of theexcavated stuff up to any lead for Soft rock

CMT 3941.00

2 Excavation for foundation in trenches up from 1.5m to 3.0m depthincluding sorting out and stacking of useful materials and disposingof the excavated stuff up to any lead for Hard rock

CMT 3665.00

3 Excavation for foundation in trenches up from 1.5m to 3.0m depthincluding sorting out and stacking of useful materials and disposingof the excavated stuff up to any lead for Hard rock

CMT 50.00

4 Filling in plinth/trenches & yard with earth in layers notexceeding200 mm, thick layers including watering, ramming,consolidating etc., complete as directed by EIC. - Excavated earthfrom foundation. The item rate includes all leads & lifts.

CMT 81.00

5 DO as per Item No.4but yellow earth/murrum of approved qualitybrought from out side.

CMT 590.00

of 45




6 Filling in plinth with sand/quarry dust under floors includingwatering, ramming, consolidating and dressing etc. complete.

CMT. 792.00

7 Precast concrete block masonry (including quoin blue jamb blocks,closer etc.) with solid concrete blocks, of approved size made ofcement concrete 1:3:6 Mix (1-Cement ; 3-Coarse sand ; 6-Gradedstone aggregates of 20mm and down gauge) in foundation andplinth in Cement Mortar 1:6.

CMT 195.00

8 DO but FOR SUPER STRUCTURE G.F+F.F+Stair Cabin CMT 295.009 Half Brick masonry in common burnt clay building bricks having

crushing strength not less than 35 kg/Sq.m in cement mortar 1:4(1cement & 4 coarse sand) up to plinth & two floors G.F+F.F+StairCabin.

SMT 135.00

10 Providing and laying cement concrete 1:4:8(1 Cement : 4 Coarseand : 8 black crushed stone aggregate 40mm nominal size ) andcuring complete- Foundation and plinth.

CMT 615.00

11 Providing and laying ordinary cement concrete M-15 for RCCstructure including finishing smooth with curing etc. comp.excluding the cost of form work but excluding the cost ofreinforcement & Providing form work of steel/ply woodplanking so as to give a smooth exposed finish includingcentering (steel adjustable tubular supports).Shutteringstrutting and propping etc.for any height of propping andcentering below supporting floor to ceiling,and removal of thesame for reinforced concrete and plain concrete for G.F+F.F+Stair Cabin

CMT 71.00

Providing & laying control cement concrete M-20 as per mix designexposed work with curing etc. complete including the cost of plywood / steel sheathing form work & adjustable tubular steelsupports / Props. but excluding the cost ofreinforcement.G.F+F.F+.G.F+F.F+Stair Cabin

12 Footing CMT 2453.0013 Columns CMT 350.0014 beam CMT 475.0015 slab ,Chhaja, & Lintel CMT 66.00

DO as above but for M-25 grade concrete as per mix design ofconcrete for exposed work.G.F+F.F+Stair Cabin

16 Footing CMT 88.0017 Column CMT 53.0018 Beam CMT 127.0019 Slab , Chajja, & Lintel,Pardi/wall etc. CMT 108.0020 Providing Thermo Mechanically treated bars (TMT bars) confirmed

to IS 1786 FE 415 for RCC work including bending, binding andplacing in position etc. completed for RCC work.

MT 219.00

of 45




21 Providing & placing 50m thick & 300 mm wide prestressedconcrete cover (for clear span up to 1.2 mtr in proportion (1:1:5:3)or M20 with necessary reinforcement of 4 MM dia H.T steel wire-4nos 4mm dia HTdistribution bars at 150 MM C/C as per drawing &design-including providing necessary MS bar hooks for liftingarrangement & vibrating with vibrators.Finishing all thesurfaces,curing by placing in water pond for ten days etc.completeas directed by EIC.(The rate includes cost of all material required,labourcharges, transportation, loading, unloading, etc.)

SMT 1135.00

22 Providing 15mm thick cement plaster single coat onmasonary/bela/concrete wall/ceiling for plastering up to any floorlevel finished even and smooth in cement mortar 1:3 (1 Cement : 3sand) finished with floating coat of neat cement slurry .

SMT 3315.00

23 Do but 15mm th. S/F plaster(Pg 115 it 17002A+ it 17004) SMT 720.0024 Providing 20mm thick sand face cement plaster on wall up to

height 10 meters above ground level consisting of 12mm thickbacking coat of C.M. 1:3 (1 cement : 3 sand) and 8mm thickfinishing coat of C.M. 1:1 (1 cement : 1 sand) etc. complete.

SMT 1034.00

25 Providing cement vata (10cmx10cm size) quarter round in cementmortar 1:1 including neat cement finishing watering etc. complete.

RMT 221.00

26 Providing distempering [Three coats] with oil bound distemper ofapproved brand and manufacture and or required shade onundecorated wall /ceilingsurface to give an even shade over andincluding a priming coat with distemper primer of approvedbrand and manufacture after thoroughly brushing the surfacefree from mortar droppings and other foreign matter and alsoincluding preparing the surface even and sand paperedsmooth

SMT 3153.00

27 Providing & applying 3 coats of ACID/ALKALI resisting paint ofapproved shade & make to wall, ceiling including filling puttysmoothing the surfaces scaffolding etc. complete as directed byE.I.C.

SMT 215.00

28 Providing & applying 2 coats of APOCOLITE APEX or itseuqi.ACRYLIC EXTERIOR paint on exiting plastered surface orapproved make & shade including finishing & thinning as permanufacture’s instruction A gap of 6 hrs.should be given between2 subsequent coats.The work should be carried out strictly as permanufacture’s specification and requirement comp.As directed byEIC

SMT 1865.00

of 45




29 Providing and fixing rolling shutters of approved make made of 80mm wide MS Laths interlocked together through their entire lengthand jointed together at the ends by end locks mounted on speciallydesigned pipe shaft with bracket plates guide channels andarrangements for inside and out side locking with push pulloperation complete with 3 coats of approved oil paint etc.complete. including the cost of hood cover and spring.

SMT 10.00

30 Providing & fixing FRP door having FRP frame of size 100 x 50mm & 28 mm thick FRP shutter with Depressed Panel shutterhaving extra reinforcement on side and edges and in Gel coatfinish.The core of the shutter is to be filled up with injected fibreextinguishing grade polyurethane foam done in situ along withembedded wooden pieces for stiffening and also for fixing hingesand fixtures.The whole FRP frame and shutter is to be waterproof, weather proof, termite proof and resistance to mildacid/Alkali resistance including SS hinges with necessary screwsand aluminum fixture and fastenings etc complete.

SMT 37.70

Providing and fixing fully glazed / partly glazed double leaf 20 SMT 56.0031

of 45




32 Providing and fixing standard extruded of alluminium section ofsize 63mm x38.10mmx1.2mm(Jindal section:2434@wt 0.643Kgper mt.) with colour anodized alluminium frame for ventilation with5mm thick frosted glasee as details etc complete for ventilation.

SMT 13.00

Providing and fixing fully glazed / partly glazed double leaf 20 micron thick colour anodized aluminium door with following listed extruded section manufactured by Jindal luminium Ltd. & other accessories,the Alluminium sections are of HE9WP Group: 1) with door outer frame section of 63.5 x 38.1 x 3.18 mm thick weighing 1.777 kg/Rmt (J4605) 2) Door shutter vertical style (meeting style) of 53.7 x 44.45 x 2.30mm thickness (J4537) weighing 1.238 Kg/m3) Hinge side 53.7 x 44.45 x 2.30mmthickness (J4540) weighing 1.173 Kg/Rmt4) Bottom rail of size 150 x 44.45 x 2.40mmthickness (J4538) weighing 2.376 Kg/Rmt 5) Lock rail of size 83.5 x 44.45 x 2.40mm thickness (J4549) weighing 1.679 Kg/Rmt 6) Top rail of size 47.62 x 44.45 x 3.18mm thickness(J4506) weighing 1.501 Kg/Rmt 7) Ventilator middle member (if required)49.91 x 44.45 x 3.00mm thickness (J4621)weighing 1.495 Kg/ Rmt 8) Aluminium handle 127.00 x 37 x 3.65mm thickness (J4483) weighing 1.912 Kg/No. 9) Tower bolt 250mm long (J4954) 10) Aluminium bending mortice lock(J4420) 11) Top panel using 6.0mm thick Triveni or Modi or Saint Gobain make float glassfixed with PVC Clear gasket 12) Bottom panel using 12mm thick exterior grade prelaminated particle board of make approved by the Engineer - in - Charge (for partly glazed door) fixed with virgin PVC clear gasket13) Door Closer of make approved by theEngineer - in – Charge. with all other required fixtures and fastening of colour anodized withaluminium beading, with all labours andmaterials etc. complete as directed by EIC.Aluminium section user for fixing hinges,door closer, etc. shall be filled with countryteak wood to receive screws.

SMT 56.0031

of 45




33 Providing and fixing window having extruded aluminiumanodized section frame main outer size 63.50x38.10x19.5mm (ofJindal Section no:4605, @ wt 1.094Kg/Rmt), horizontal two trackmember size 61.85mm x 31.75mm x 1.20mm(of Jindal Section mo:8687 @ wt of 0.695 Kg/mt), vertical member of size 61.85mm x31.75mm x1.30mm(of Jindal section no: 8758 @ wt of 0.659 Kg/mt) with Sliding Shutters of horizontal member Size 40mm x18mm x 1.29mm(of Jindal section no: 8949 @ wt of 0.456Kf/mt),vertical member of size 40mm x 18mm x 1.29mm (of Jindal Sectio:8947 @ wt 0.457 Kg/mt, section 8948 @ 0.457kG/mt) with 5 mmthick transparent bronze colour/white tinted float glass with powdercoated aluminium fittings and fixtures and transparent siliconsealant glass fixing to frame as per details etc complete forWindow.

SMT 98.00

34 Providing & fixing MS Grill of approved quality & design weighing25 to 30 kg/SMT. as per drawing & as directed with necessary grilldoor (if required) including welding or bolted fixtures and fastening.M.S. Flat hold fasts, 300mm long, 16mm dia. aldrop & 300mm.long tower bolt necessary with handles etc. with 3 coats of oilpainting of approved shade & tint with one coat of red oxideprimer including grouted hold fast in CC (1:2:4) etc. complete asdirected by EIC.

KG. 1950.00

35 Providing and laying approved quality polished Kotah stoneslab(25mm th.) flooring including using 35x25mm approvedquality machine cut, marble strip over 20mm (average) thick baseof cement mortar 1:6 (1 cement : 6 course sand )or L.M. 1:1.5 laidover and jointed with grey cement slurry including rubbing andmirror polishing using polishing machine with grinding six emery'sof different no. including using special chemical powder forpolishing including white cement coating two times during polishingfor filling up minute holes or cracks in joints etc. comp.

SMT 300.00

36 Providing and laying polished Kota stone slab 25 mm th. in risersof steps, Dedo and sills laid on 10 mm thick CM 1:3 & jointed withgrey cement slurry including rubbing and polishing etc. complete.

SMT 150.00

37 Providing and laying color glazed tiles-JOHNSON/KAJARIA/NITTCO or its equivalent make 6mm thick inflooring & Dedo laid on bed of 12mm thick cement mortar 1:3 (1cement : 3 course sand) & fixing the same in cement & providing12mm thick back coating of cement plaster in CM 1:3 for base,filling the joints with white/color cement neatly finishing the jointscuring etc. complete.

SMT 315.00

of 45




Providing & Fixing UPVC pipe of Dutron made( Hiflow type)Schedule - 80( IS :4985 & IS : 12818 ) or Equivalent make in wall,Ceiling or in trenches including excavation & also includingnecessary feetings & fixures (except special fitting) as directed byE.I.C. -

38 (A) 25mm pipe. RMT 425.0039 (B) 40mmpipe RMT 850.00

Providing & fixing approved quality gun metal check or non-returnwheel valve

40 (B) 25MM DIA NO 52.0041 Providing and fixing approved quality screw down bib tapes of

following size: (A ) Brass screw down bib tap polishedbright 15mm dia.

NO 78.00

42 Providing & fixing approved quality readymade P.V.C. water tightstorage tank of 1000 liters capacity made from linear low densitypolythene & low density polythene LDPF product confirming to I.S.: 10146-1982 with cover including providing & fixing one 20mm dia,float valve ball-cock, one 20mm dia G.I. over flow pipe of length upto 0.30 Mt. including making all connection for inlet/outlet etc.complete as directed by E.I.C.

NO 6.00

Providing & Fixing FINOLEX brand or equivalent rigid PVC. Pipe 6kg / cm2 for rain water including necessary fittings like bends shoe,cowl etc.& fixing the pipes to the wall in plumb by means ofGI.Clamps of 18 gauge sheet with 1 to1.5 meter distance,filling thejoints with approved solution complete as directed by EIC.

43 (A) 90MM DIA O.D.P.V.C. pipe RMT 114.0044 (B) 110 MM PVC PIPE RMT 50.0045 Providing and laying (to level or slopes) and jointing with stiff

mixture of cement mortar in proportion 1:1 approved quality saltglazed stoneware pipes of 100 mm nominal internal diametersincluding testing of pipes and joints complete.

RMT 40.00

45 Providing and laying (to level or slopes) and jointing with stiffmixture of cement mortar in proportion 1:1 approved quality saltglazed stoneware pipes of 150 mm nominal internal diametersincluding testing of pipes and joints complete.

RMT 355.00

46 Providing and fixing approved quality .C.I. Nahani trap ofapproved size & make with additional aluminum perforated jalicover & C.I. Pipe outside the wall with plug, bend, etc. complete asdirected by E.I.C.

NO 18.00

47 Providing and fixing approved quality S.W. gully trap with C.I.Grating, brick masonry chamber and water tight C.I. cover withframe of 300 mm x 300 mm size (inside) with standard weight. (B) 150 mm x 100mm size P or R type.

NO 14.00

of 45




48 Providing B.B. Masonry inspection chamber (MANHOLE) of600mm x600mm size including light type approved C.I. Cover withframe, necessary excavation, bottom concreting of B.B.C.C. (1:4:8)150mm thick/225mm, thick B.B. Masonry in C.M. (1:6) 12mm thickcement plaster in C.M. (1:3) inside & to all exposed faces up to300mm below ground level, curing etc. including disposal ofsurplus excavated earth up to radius of 500mt. including 3 coats ofwhite or colour wash to all exposed finished surface etc. completeas directed by EIC. (B.B. Masonry up to 1000mm depth).

NO 15.00

49 Providing & Fixing 450X400mm size Stainless Steel approvedbrand Kitchen Sink Incl waste pipe & Coupling etc; complete asdirected by EIC.

No 5.00

50 Providing and fixing approved quality ORISSA PAN water closetsquatting pan size 580mm including providing and fixing 100mmsize P or S trap jointing tap with the pan and soil waste pipe andwith G.I. inlet connection for flush pipe with W.C. pan of approvedquality of 25mm dia etc. complete.

NO 7.00

Providing & fixing approved quality light type C.I. Manhole coverswith water tight C.I. Frame & fixing the same in concrete etc.complete as directed by E.I.C.

51 (A) 600X600mmsize NO 14.0052 Providing and fixing urinal of approved quality including

connection with trap and with integral longitudinal flush pipeconcealed outlet (A) squaring plate pattern white earthenware550mm x 300mm

NO 3.00

53 Providing and fixing to wall, ceiling and floor 6.0 Kg f/cm2 workingpressure polythelene pipes of the following outside dia. Lowdensity, complete with special flange compression type fittings wallclamps etc. including making good the wall, ceiling and floor(20mm dia.)

RMT 50.00

54 Drilling of bore well of 165mm dia by machine in all kind of soil,sand, clay Murrum, soft rock and hard rock etc. complete trulyvertical with equipments and labors etc. complete as directed byE.I.C.(As per lakhabaval)

RMT 150.00

55 Providing, fixing & lowering heavy duty 10kg/cm2 PVC casing pipesuitable for 165mm dia.mm. bore well including necessarycoupling connector solution etc. complete as directed by EIC.

RMT 10.00

56 Providing, fixing approved quality of HDPE pipe of ISI quality withall accessories fittings, jointing etc. suitable for submersible pumplowering in bore etc. complete as directed by EIC. - 32mmdia.(outer)10kg/cm2

RMT 110.00

of 45




57 Providing & fixing approved quality top cap for 150mm dia. Pipeclamps, socket & other accessories required for completing the jobas directed by EIC

NO. 1.00

58 Supplying and lowering the Calama/Jyoti/ Kirloskar/ Amrut or KSBmake submersible pump of 3.0 hp x 24 stage in bore well etccomplete as directed including ISI approved MEI type oil immersedauto transformer starter commissioning and testing to requireddelivery head. (All other accessories will be paid separately)(as perlakhabaval)

NO. 1.00

59 Providing & joining approved quality flat Copper cables sufficientfor 3 HP pump set etc complete a 4mm flat cable.

RMT 110.00

60 Providing & fixing approved quality single phase monoblock / selfpriming pump of ISI brand (2H.P)with all GI fitting for inlet & outletconnection including providing G.M.Wheel valve required electricfitting / switch board etc. comp.

NO 1.00

61 Providing and fixing approved quality control panel board metalbox I.S.I. with a main fuse connection ampere meter, volt meter 30Amp. 1 phase switch single phase preventor cum water levelguard and male and female type socket 1 phase indicator lampsand toggle switch etc. including all wiring/earthling completed asdirected by E.I.C.

NO 1.00

62 Supplying & stacking 40 to 60mm size hard stone road blackcrushed metal including transportation filling the box etc. complete.(box measurement shall be paid with 20% void deduction)- Forroad work.

CMT 375.00

63 Supplying & stacking 25 to 40mm size crushed metal includingtransportation, filing the box etc. complete as directed by EIC. (Boxmeasurement will be paid with 15% voids deductions)- For yardmetal spreading.

CMT 2250.00

64 Supplying & stacking Quarry dust including transportation forspreading on road filling the box etc. complete.

CMT 1425.00

65 Supplying & stacking murrum of approved quality includingtransportation, filling the boxes etc. completed as directed. (Boxmeasurement will be paid with 15% deduction of voids).

CMT 130.00

66 Labour charges for spreading 40 to 60 mm size metal in 100mmthick layers with required grade & camber & watering rolling theeach layer with 8 to 10 tones power roller including fillingdepression which occur during process etc. complete as directedby EIC.

SMT 950.00

67 Labour charges for spreading 25 to 40 mm size metal in yard asdirected by EIC.

SMT 24900.00

68 DO as above (item No 70) but with murrum SMT 3750.0069 DO as above but for Quarry Dust in yard. SMT 24900.00

of 45




70 Providing & placing 60MM thick grey colour PAVERS PRECASTCONCRETE BLOCK of approved quality size & shape in line &level including fitting in 50MM average thick layer approved qualityof river sand below concrete block, slope filling the joint ofconcrete block etc.complete as directed by EIC.

SMT 400.00

71 Providing and fixing approved quality 600mm x 450mm bevelededge mirror of superior glass mounted on PVC moulded frame andfixed to wooden plugs with C.P. brass screws and washers.

NO 7.00

72 Providing & fixing approved quality 300x300mm size marble yearplate with black border all round & letters including fixing the samein cement mortar etc. comp. As directed by EIC.

NO 3.00

73 Providing and fixing approved quality C.P. Brass towel rodcomplete with C.P. Brass brackets fixed to wooden plugs with C.P.Brass screws. 600mmx20mm size

NO 6.00

74 Providing & laying `A' Class R.C.C. NP3 hume pipe includingnecessary excavation, refilling the trenches, laying 150mm.thickB.B.C.C.(1:4:8) below joints up to half the height of joints makingwater tight joints in C.M.(1:1) curing etc., complete as directed byE.I.C.) 300mm.dia. Pipe(pg 168 it 26089AA)

RMT 50.00

75 Providing & applying anti termite treatment, as per IS 6313 (Part.II& II 2001) for building works in pre construction & post const.stages, using chemicals conforming to relevant IS in wateremulsion and effective when applied uniformly over the area to betreated. The chemical to be used is chlorophriphos 20% EC or itsequivalent. The treatment is to be carried out as per the procedurementioned below and treated plinth surface area is to be taken formeasurement. (with performance guarantee for 5 years)a)For preconstruction treatment: For plinth filling & periphery holes in sideplinth to be drilled 300MM C/C each having depth 1.5M and forinside plinth the hole are to be treated with diluted chemicalsolution, 1.5 lit. per hole, in the ratio of 1:20. For periphery i.e. outside plinth the ditch is to be treated with diluted solution 2.25 litreper rmt. In the ratio 1:20. The entire surface area is to be treatedwith diluted solution of dose 2.5 litres per smt. over and above as aplinth surface treatment.The contractor shall submit performanceguarantee of the anti termite item at the rate of 20% of cost of item of work order in the form of FDR of Schedule Bank / Nationalised Bank in favour of GETCO (A/c Agency) for a period of 5 years from actual date of completion of work stamp paper of appropriate value in approved format of GETCO.

SMT 785.00

of 45




76 Setting of template & foundation bolts in line and level beforeconcreting of foundation and making arrangement of fixingtemplate in such a way as it remains in position during concreteetc. comp. As directed by EIC.Note:The rate includes supplying and fabricating of template as per template drawing including all materials,tools,tackles and labouresrequired for that.No extra payment for preparation of template willbe given.The templates prepared are the property of agency.

NO. 750.00

77 Providing 2500mm internal diameters & 4.00 Mt deep soak pitincluding excavation in all types of soil & soft rock & B.B.C.C.(1:4:8) bedding 300mm thick below masonry and 450mm thickbrick masonry in C.M. (1:6) up to 600mm height 350mm thick forfurther 600mm & 230mm thick for remaining height honey combed,plastering in C.M.(1:3) outside up to 1.5mt height and 100mm thickRCC slab with 600x600mm CI having cover with frame, withnecessary reinforcement as per design & CI vent pipe 1800mmlong with brick masonry pillar 3500x350x450 plastered all aroundfilling 40 to 50mm brick bats up to 1.5Mt depth including 16mm diaMS"U" stages steps refilling including disposal of the surplusexcavated earth up to the lead of 300Mt radius including 3 coats ofwhite or colour wash to all exposed finished surface etc. completedas directed.

NO. 3.00

78 Providing & fixing 75mm dia. PVC Cowl vent of light type. NO. 5.0079 Providing & fixing M.S. ladder 450mm wide or 50x6mm M.S. flat

and 16mm dia M.S. Bars welded as step at 300mm C/C and fixingthe ladder & 3 coats of oil painting etc. complete as directed byE.I.C.

RMT 16.00

80 Providing & Fixing approved quality a set of 6 Nos. of stainlesssteel coat racks of approved quality fixed on 20 mm. thick teakwood batten including 3 coats of oil painting etc., complete asdirected by E.I.C

NO 6.00

81 Providing & laying 40mm th. IPS flooring in CC 1:2:4 includingfinishing the floor with smooth cement slurry marking diagonal linesetc. complete.(pg 73 R & B)

SMT 70.00

82 Providing & laying rigid 10 kg/cm2 PVC drainage pipe includingnecessary fittings like bend, tee,Y bend plug etc. fixed with wall bymeans of clamps & nails with water tight joints by approvedsolution etc. complete as directed by EIC.

83 (A) 75mm dia. pipe RMT 450.0084 (B) 100mm dia. pipe RMT 80.00

of 45




85 Providing & fixing special GI Brand or it's equivalent ISI approvedquality fittings including cutting the pipe threading making watertight joint etc. complete as directed byEIC.

86 Elbow for 50 mm dia GI Pipe NO. 3.0087 Union for 50 mm dia GI Pipe. NO. 3.0088 Supply and fixing approved quality following fixtures and

fastenings of approved quality with wooden or metal screws, nutsand bolts as directed or as per the drawing & specifications etc.complete as directed by EIC. -Tower bolt : 150mm.long &10mm.dia. to doors & windows, ventilators cup boards

NO. 11.00

89 Do…Do…. Brass C.P. mortise lock (GORE MAKE) withhandles of approved quality

NO. 5.00

90 Do….Do….M.S. best chromium plated aldrop 16mm. dia. &300mm. long.

NO. 12.00

91 Do….Do…..M.S. best chromium plated latch 10mm Dia. And250mm long.

NO. 12.00

92 Do….Do….Brass C.P. Rubber stopper. (For Door) NO. 11.0093 Do….Do…. HEAVY ALUMINUM PLATE SECTION HANDLE

3mm. to 4mm. thick & 150mm. long.NO. 21.00

94 Providing & laying water proofing treatment on terrace includingapplying neat cement slurry 2.75 kg./sq.mt. on cement admixedwith water proofing component after cleaning the surface, Layingcement concrete with brick bat 75mm to 100mm thick with 50% ofC.M. 1:5 admixed with water proofing component over 20mm thicklayer of C.M. 1:5 to required slope including ramming at junction ofwall and slab, after two days of proper curing applying a secondcoat of cement slurry, finished the surface with 20mm thick C.M.1:4 china mosaic flooring and finally finishing flooding 75mm deepwith water on terrace for a period of two week. The contractorshall submit performance guarantee of the waterproofing item atthe rate of 20% of cost of item of work order in the form of FDR ofSchedule Bank / Nationalised Bank in favour of GETCO (A/cAgency) for a period of 5 years from actual date of completion ofwork stamp paper of appropriate value in approved format ofGETCO.

SMT 835.00

95 Supply, fabrication,cutting,threading of M.S rod including hot dipgalvanizing the same of required size and length including 2 Nos of nuts and pack/spring washers etc; complete as directed by E.I.C

KG. 16000.00

of 45




96 Providing and fixing wash basin with single hole pillar tap with tapwith C.I. or M.S. brackets painted while/colour including cuttingholes and making good the hole including pillar tap,chromiumplated bottle trap,stop cock, fisher union, Brass waste pipe etccomplet. 550 x 440 mm(pg 142 it 23018+23020B+23021B+23036)

NO 6.00

97 Providing & fixing in position approved quality 35mm. thick fullypaneled teakwood door with100X75mm size teak wood frame withsingle or double shutters with 100X35mm. size styles and top railsand bottom rail of 125X35mm. and lock rail 175X35mm. including100 mm to 125 mm x 20mm thick equal size vertical battens inpanels with tongue and groove arrangement as per drawing aspanels without fixtures and fastening but with 3No. of 100mm. longbutt or parliamentary hinges for each flap of double shutter and150mm long to single shutter as per instructions including 3 No. ofM.S. flat hold fast grouted in wall on each side, 3 coats of oilpainting with primer of approved shade and make etc., completeas per drawing & as directed by E.I.C. (FIXTURES EXCEPTHINGES AND HOLD FASTS WILL BE PAID SEPARATELY.)

SMT 21.00

98 Providing & fixing built in wall teak wood cup board having75x50mm teakwood frame & 35mm, thick shutter frame withapproved quality of 20 Gauge GI wire mesh jail (MOSQUITOPROOF) as panels fixed with teak wood shutter frame & battensetc. including fixtures & fastening & with 150mm long 3 nos. ofhinges on each flap of shutter and 3 coats of oil paint includingprimer of approved shade & make and as per drawings etc.complete as directed by EIC.

SMT 3.00

99 Providing & fixing approved quality steel cupboard shutter of 18gauge with steel frame and fixing the frame with brick masonryincluding locking arrangement with 3 coats of approved oil paintetc. complete.

SMT 16.00

100 Providing cooking RCC platform of 3000x675mm size withapproved quality of circular stainless steel sink of size 450mm dia.& 4 nos. of partition walls (middle) with cement plaster in CM 1:3 toall exposed faces, 75mm thick RCC slab in CC (1:2:4) withnecessary reinforcement, making hole in slab for gas connection,including Kotah stone flooring with side Patti of required size &thickness, with polishing etc., complete & fixing teak woodcupboard of frame size 75x50mm with shutter for opening of size1.20x0.60mtr. made from 12mm thick nova pan/eco board exteriorlaminated with all round teak wood batten Patti including two coatsof oil paintings & one coat of primer including PVC waste pipe,Nahani trap, bibcock, etc. complete as per drawing & instruction ofEIC.

SMT 4.00

of 45




101 Providing & fixing 18 gauge wire mesh jali having width 200 to 300mm with nails before finishing the surface with plaster. The itemincludes providing necessary scaffolding also)

SMT 130.00

102 Providing supplying fabricating and erecting chain link fencingpanel of size 2400x2000mm made from 75x75mm & 10 gauge GIchain link & 50x50x6mm angle including fixing and chain link inangle frame by means of 40x3 mm MS flat welded to angle frame.Drilling of holes in angle frame and flat, fixing the same with anglepost in line, level and plumb by means of 10 mm dia bolts and nutsin frame and flat with hot deep galvanizing as per IS-2633/72 &209 of 1966 or latest amendment, etc complete as per drawing asdirected by EIC. (All this materials like MS flat, chain link fencing,MS angles, bolts, nuts will have to be supplied by the contractor)Note: for add size payment will be made on SMT basis.

KG. 4000.00

103 Providing & fixing G.I. Barbed wire fencing (12/14 Gauge) havingmass and uniformity of Zinc coating & specifications shall be asper IS 2140 – 1978 & IS 4826 – 1979 code with minimum 70micron coating having 3 horizontal rows, fixing with angle posts bymeans of G.I. U pins or with R.C.C. poles by 14 Gauge G.I. Wireas per drawing etc., complete as directed by E.I.C. (as perVallbhipur -ph -ii it 58)

RMT 90.00

104 Providing and laying 24"x24" Vitrified 8 mm thick tiles flooring over20mm(Average) base of Cement Mortar 1:6 (1-Cement : 6 CoarseSand) on new surface or fixing on existing flooring by adhesivematerials including dismentalling of existing flooring and jointedwith colour cement slurry including finished with flush pointing &cleaning the surface etc complete for light shade.

SMT 445.00

105 Setting of rail for transformer plinth in line and level & gaugebefore concreting of foundation and making arrangement of fixingtemplate in such a way as it remains in position during concreteetc. comp. As directed by EIC.

SET 4.00

106 Providing and laying polished Kota stone slab 25 mm th. in risersof steps, Dedo and sills laid on 10 mm thick CM 1:3 & jointed withgrey cement slurry including rubbing and polishing etc. complete.

SMT 103.00

107 Steel work welded in built up sections,framed work includingcutting, histing, fixing in position and applying a priming coat of redlead paint :- (A) In beams and joints channels angles, tees, flatswith connecting cleats as in main and cross beems, hip and jackreffers, purlins connected to common raffers and the like &.Intrusses and trussed purlins upto 25 m. span and 15 m. overallheight

KG. 16700.00

of 45




108 Providing & fixing Acrylic name plates of required size includingpainting letters as directed & fixing as directed by E.I.C.(as perlakbabaval it 103)

No. 11.00

109 Earthwork for embankment including breaking clods, dressing withall lead and lift (including watering, rolling and consolidation with 8to 10 T rollers inlayers at O.M.Cto required dry density). Includingall Labour charges & approved quality of Earth/Murrum & Govt.royalty charges etc. if applicable. Approved quality of yellowearth/Murrum to be brought from outside.)

SMT 950.00

110 Providing & Laying 75 mm thick built up spray grout base coursedouble layer using tack coat at the rate of 5 Kg. of asphalt ofrequired grade per 10 m2 for first layer and 15 Kg. of asphalt ofrequired grade per 10 m2 for grouting for second layer as perrequirement and spreading grit at the rate of 0.50 m3 per 10 m2 ineach layer of road surface using 0.13 m3 of key aggregate of size40 mm to 50 mm (black trap metal) per 10 m2 area over existingsurface including rolling & consolidating with 8 to 10 tonnes powerroller for each layer etc., complete as per specification and asdirected by E.I.C.

SMT 3230.00

111 Providing & laying 40 MM. CONSOLIDATED THICK (5.5 m3 / 100m2) premix asphalt carpet by using 2.4m3/100 m2 black trap 25mm. chips, 2.5m3/100 m2 12mm. size black trap chips and 0.6 m3/ 100 m2 6 mm. size black trap grit using asphalt for mixing 48 Kg./m3 for 25 mm. size black trap chips, 52 Kg./ m3 for 12mm. sizeblack trap chips & 56 Kg./ m3 for 6 mm. size black chips and usingtack coat of 100 Kg. / 100m2 including heating asphalt to requiredtemperature cleaning, brushing the road surface mixing includingall labours & cost of asphalt, solvent with all tools plant etc.,complete as directed, including consolidating by 8 to 10 tonnescapacity roller.

SMT 3230.00

112 Providing & Laying consolidated 12mm. thick premixed seal coaton asphalt carpet with tack coat of bitumen of 10 Kg. per 10 m2and 0.1 m3 of grit mixed with 13 Kg. of asphalt includingconsolidating by 8 to 10 tonnes of power roller and spreading sandover rolled surface at rate of 0.3 m3 / 10 m2 including cleaning theexisting surface with wire brush etc., complete as directed.(GETCOSOR PG NO 83 IT 14)

SMT 3230.00

113 Providing & Applying hot bitumen as per specification as a liquidseal coat at the rate of 10 Kg. per 10 m2 area including cleaningsurface and applying hot bitumen uniformly with brush andspreading sand at the rate of 0.1 m3 per 10 m2 area rolling with 8to 10 tonnes power roller etc., complete as directed by E.I.C.

SMT 3230.00

of 45




114 Drilling of Bore holes 32mm to 40mm dia by means of compressor machine having depth of hole up to 1.20 mt. as decided by Engineer in charge & as per drawing in all sorts of Soil, sand, clay, hard rock etc. truly vertical to existing land with cleaning the same by air & Grouting of Bores holes 32 mm to 40 mm dia with depth up to 1.20 mt by means of Cement, sand, Grit, etc. with utilization of aluminum powder or ACC shrink compound ‘N’ grout or equivalent any other bonding material as approved by competent authority in suitable content with mixing ramming curing etc. complete including with 20mm dia. of M.S. Anchor bar (Reinforcement) ( The rate includes the cost of MS Anchor bar) as directed by Engineer in charge.

No. 2904.00

NOTE:-

Cost of inland Freight and inland insurance in India.

The bidder should quote as per ITB 18.4(d)The bidder shall specify the applicable local taxes description and rates.

Name of Bidder

Signature of Bidder

1 Specify currency in accordance with ITB 19.

TOTAL Columns 6 and 7 to be carried forward to Schedule No.5. Grand Summary

It is desired that transportation of equipments / material in India should be arranged only

of 45

220KV Moti Gop AIS SUBSTATION Schedule No. 4 … Office/0-2016/260416_A... · Tandem DB Isolator...

Documents

Transcript of 220KV Moti Gop AIS SUBSTATION Schedule No. 4 … Office/0-2016/260416_A... · Tandem DB Isolator...