2018 Dodge Durango Owner's Manual · INTRODUCTION Dear Customer, congratulations on selecting your...

DurangoOWNER’S MANUAL

1 8 W D - 1 2 6 - E N A - A A©2017 FCA US LLC. All Rights Reserved.Dodge is a registered trademark of FCA US LLC.

Table of Contents1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 GRAPHICAL TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 GETTING TO KNOW YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4 GETTING TO KNOW YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

5 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

6 STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

7 IN CASE OF EMERGENCY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211

8 SERVICING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235

9 TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265

10 MULTIMEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

11 CUSTOMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319

12 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323

1

1INTRODUCTION

• INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4• ROLLOVER WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4• IMPORTANT NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5• HOW TO USE THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . .5

• Essential Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5• Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

• WARNINGS AND CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .7• VEHICLE MODIFICATIONS/ALTERATIONS . . . . . . . . . . . . . . . . . . .7

3

INTRODUCTIONDear Customer, congratulations on selectingyour new vehicle. Be assured that it representsprecision workmanship, distinctive styling, andhigh quality.

This is a specialized utility vehicle. It can goplaces and perform tasks that conventional pas-senger vehicles are not intended. It handles andmaneuvers differently from many passenger ve-hicles both on-road and off-road, so take time tobecome familiar with your vehicle. If equipped,the two-wheel drive version of this vehicle wasdesigned for on-road use only. It is not intendedfor off-road driving or use in other severe con-ditions suited for a four-wheel drive vehicle.Before you start to drive this vehicle, read theOwner’s Manual. Be sure you are familiar withall vehicle controls, particularly those used forbraking, steering, transmission, and transfercase shifting. Learn how your vehicle handleson different road surfaces. Your driving skills willimprove with experience. When driving off-road,or working the vehicle, don’t overload the ve-hicle or expect the vehicle to overcome thenatural laws of physics. Always observe federal,state, provincial and local laws wherever youdrive. As with other vehicles of this type, failureto operate this vehicle correctly may result inloss of control or a collision. Refer to the “DrivingTips” section for further information.

This Owner’s Manual has been prepared withthe assistance of service and engineering spe-cialists to acquaint you with the operation and

maintenance of your vehicle. It is supplementedby Warranty Information, and customer orienteddocuments. In the attached Warranty Bookletyou will find a description of the services thatFCA offers to its customers, the Warranty Cer-tificate and the details of the terms and condi-tions for maintaining its validity. Please take thetime to read all of these publications carefullybefore driving your vehicle for the first time.Following the instructions, recommendations,tips, and important warnings in this manual willhelp assure safe and enjoyable operation ofyour vehicle.

This Owner’s Manual describes all versions ofthis vehicle. Options and equipment dedicatedto specific markets or versions are not expresslyindicated in the text. Therefore, you should onlyconsider the information which is related to thetrim level, engine, and version that you havepurchased. Any content introduced throughoutthe Owner’s Information, that may or may not beapplicable to your vehicle, will be identified withthe wording “If Equipped”. All data contained inthis publication are intended to help you useyour vehicle in the best possible way. FCA aimsat a constant improvement of the vehicles pro-duced. For this reason, it reserves the right tomake changes to the model described for tech-nical and/or commercial reasons. For furtherinformation, contact an authorized dealer.

If applicable, refer to the owners manual supple-ment for related information.

NOTE:After reviewing the Owner’s Information, itshould be stored in the vehicle for convenientreferencing, and remain with the vehicle whensold.

When it comes to service, remember that yourauthorized dealer knows your vehicle best, hasfactory-trained technicians and genuineMOPAR® parts, and cares about your satisfac-tion.

ROLLOVER WARNINGUtility vehicles have a significantly higher roll-over rate than other types of vehicles. Thisvehicle has a higher ground clearance and ahigher center of gravity than many passengervehicles. It is capable of performing better in awide variety of off-road applications. Driven inan unsafe manner, all vehicles can go out ofcontrol. Because of the higher center of gravity,if this vehicle is out of control it may roll overwhen some other vehicles may not.

Do not attempt sharp turns, abrupt maneuvers,or other unsafe driving actions that can causeloss of vehicle control. Failure to operate thisvehicle safely may result in a collision, rolloverof the vehicle, and severe or fatal injury. Drivecarefully.

4

Failure to use the driver and passenger seatbelts provided is a major cause of severe or fatalinjury. In a rollover crash, an unbelted person issignificantly more likely to die than a personwearing a seat belt. Always buckle up.

IMPORTANT NOTICEALL MATERIAL CONTAINED IN THIS PUBLI-CATION IS BASED ON THE LATEST INFOR-MATION AVAILABLE AT TIME OF PUBLICA-TION APPROVAL. THE RIGHT IS RESERVEDTO PUBLISH REVISIONS AT ANY TIME.

This Owner’s Manual has been prepared withthe assistance of service and engineering spe-cialists to acquaint you with the operation andmaintenance of your new vehicle. It is supple-mented by a Warranty Information Booklet andvarious customer-oriented documents. You areurged to read these publications carefully. Fol-lowing the instructions and recommendations in

this Owner’s Manual will help assure safe andenjoyable operation of your vehicle.

After you have read the Owner’s Manual, itshould be stored in the vehicle for convenientreference and remain with the vehicle whensold.

The manufacturer reserves the right to makechanges in design and specifications, and/or tomake additions to or improvements in its productswithout imposing any obligations upon itself toinstall them on products previously manufactured.

The Owner’s Manual illustrates and describesthe features that are standard or available asextra cost options. Therefore, some of theequipment and accessories in this publicationmay not appear on your vehicle.

NOTE:Be sure to read the Owner’s Manual first beforedriving your vehicle and before attaching orinstalling parts/accessories or making othermodifications to the vehicle.

In view of the many replacement parts andaccessories from various manufacturers avail-able on the market, the manufacturer cannot becertain that the driving safety of your vehicle willnot be impaired by the attachment or installationof such parts. Even if such parts are officially-approved (for example, by a general operatingpermit for the part or by constructing the part inan officially approved design), or if an individualoperating permit was issued for the vehicle afterthe attachment or installation of such parts, it

cannot be implicitly assumed that the drivingsafety of your vehicle is unimpaired. Therefore,neither experts nor official agencies are liable.The manufacturer only assumes responsibilitywhen parts, which are expressly authorized orrecommended by the manufacturer, are at-tached or installed at an authorized dealer. Thesame applies when modifications to the originalcondition are subsequently made on the manu-facturer’s vehicles.

Your warranties do not cover any part that themanufacturer did not supply. Nor do they coverthe cost of any repairs or adjustments that mightbe caused or needed because of the installationor use of non-manufacturer parts, components,equipment, materials, or additives. Nor do yourwarranties cover the costs of repairing damageor conditions caused by any changes to yourvehicle that do not comply with the manufactur-ers specifications.

HOW TO USE THIS MANUAL

Essential InformationConsult the Table of Contents to determine whichsection contains the information you desire.

Since the specification of your vehicle dependson the items of equipment ordered, certaindescriptions and illustrations may differ fromyour vehicle’s equipment.

The detailed index at the back of this Owner’sManual contains a complete listing of all sub-jects.

Rollover Warning Label

5

SymbolsConsult the following table for a description ofthe symbols that may be used on your vehicle orthroughout this Owner’s Manual:

6

WARNINGS AND CAUTIONSThis Owner’s Manual contains WARNINGSagainst operating procedures that could result ina collision, bodily injury and/or death. It alsocontains CAUTIONS against procedures thatcould result in damage to your vehicle. If you donot read this entire Owner’s Manual, you maymiss important information. Observe all Warn-ings and Cautions.

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this ve-hicle could seriously affect its roadworthinessand safety and may lead to a collision result-ing in serious injury or death.

7

2GRAPHICAL TABLE OF CONTENTS

• FRONT VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10• REAR VIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11• INSTRUMENT PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12• INTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

9

FRONT VIEW

Front View

1 — Doors 4 — Wheels/Tires2 — Exterior Mirrors 5 — Hood/Engine Compartment3 — Windshield 6 — Headlights

10

REAR VIEW

Rear View

1 — Rear Lights2 — Rear Windshield Wiper3 — Liftgate

11

INSTRUMENT PANEL

Instrument Panel

1 — Air Vents 4 — Instrument Cluster2 — Paddle Shifter (–) 5 — Paddle Shifter (+)3 — Steering Wheel 6 — Radio

12

INTERIOR

Interior

1 — Door Locks/Window Switches 4 — Climate Controls2 — Seats 5 — Switch Panel3 — Gear Selector 6 — Glove Compartment

13

3GETTING TO KNOW YOUR VEHICLE

• KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19• Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

• IGNITION SWITCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21• Keyless Push Button Ignition . . . . . . . . . . . . . . . . . . . . . . . . .21• Ignition Or Accessory On Message . . . . . . . . . . . . . . . . . . . . . .22• Dead Key Fob Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

• REMOTE START — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . .23• How To Use Remote Start . . . . . . . . . . . . . . . . . . . . . . . . . . .23• Remote Start Abort Message — If Equipped . . . . . . . . . . . . . . . .23• To Enter Remote Start Mode . . . . . . . . . . . . . . . . . . . . . . . . . .23• To Exit Remote Start Mode Without Driving The Vehicle . . . . . . . . .24• To Exit Remote Start Mode And Drive The Vehicle . . . . . . . . . . . . .24• Remote Start Comfort Systems — If Equipped . . . . . . . . . . . . . . .24

• SENTRY KEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24• Customer Key Programming . . . . . . . . . . . . . . . . . . . . . . . . . .24• Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

• VEHICLE SECURITY ALARM — IF EQUIPPED . . . . . . . . . . . . . . . .25• To Arm The System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25• To Disarm The System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25• Rearming Of The System . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

• DOORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26• Manual Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26• Power Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27• Keyless Enter-N-Go — Passive Entry . . . . . . . . . . . . . . . . . . . .27• Automatic Unlock On Exit Feature — If Equipped . . . . . . . . . . . . .29• Automatic Door Locks — If Equipped. . . . . . . . . . . . . . . . . . . . .29

15

• Child-Protection Door Lock System — Rear Doors . . . . . . . . . . . .29• SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

• Manual Adjustment (Front Seats) . . . . . . . . . . . . . . . . . . . . . . .30• Power Adjustment (Front Seats) — If Equipped . . . . . . . . . . . . . . .31• Power Passenger Seat Adjustment — If Equipped . . . . . . . . . . . . .32• Driver Memory Seat — If Equipped . . . . . . . . . . . . . . . . . . . . . .33• Heated Seats — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .35• Front Ventilated Seats — If Equipped . . . . . . . . . . . . . . . . . . . .36• 60/40 Split Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37• Rear Captain’s Chairs — If Equipped . . . . . . . . . . . . . . . . . . . . .38• Folding Third Row . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

• HEAD RESTRAINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40• Supplemental Active Head Restraints — Front Seats. . . . . . . . . . . .40• Head Restraints — Rear Seats . . . . . . . . . . . . . . . . . . . . . . . . .41• Head Restraint Removal — Rear Seats . . . . . . . . . . . . . . . . . . . .42• Power Folding Third Row Head Restraints . . . . . . . . . . . . . . . . . .42

• STEERING WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43• Tilt/Telescoping Steering Column . . . . . . . . . . . . . . . . . . . . . . .43• Power Tilt/Telescoping Steering Column — If Equipped . . . . . . . . . .43• Heated Steering Wheel — If Equipped . . . . . . . . . . . . . . . . . . . .44

• MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44• Inside Day/Night Mirror — If Equipped . . . . . . . . . . . . . . . . . . . .44• Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . .44• Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45• Outside Automatic Dimming Mirrors — If Equipped . . . . . . . . . . . .45• Power Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45• Heated Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .45• Tilt Side Mirrors In Reverse (Available With Memory Seat Only) — If

Equipped. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46• Illuminated Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . .46

• EXTERIOR LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46• Headlight Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46• Daytime Running Lights — If Equipped . . . . . . . . . . . . . . . . . . .47• Multifunction Lever. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

16

• High/Low Beam Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47• Automatic High Beam — If Equipped . . . . . . . . . . . . . . . . . . . . .47• Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47• Automatic Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47• Parking Lights And Panel Lights. . . . . . . . . . . . . . . . . . . . . . . .48• Headlights On Automatically With Wipers . . . . . . . . . . . . . . . . . .48• Headlight Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48• Lights-On Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48• Fog Lights — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .48• Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48• Lane Change Assist — If Equipped . . . . . . . . . . . . . . . . . . . . . .49• Automatic Headlight Leveling — HID Headlights Only . . . . . . . . . . .49• Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

• INTERIOR LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49• Courtesy Lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

• WINDSHIELD WIPERS AND WASHERS . . . . . . . . . . . . . . . . . . . .50• Windshield Wiper Operation . . . . . . . . . . . . . . . . . . . . . . . . . .50• Rain Sensing Wipers — If Equipped . . . . . . . . . . . . . . . . . . . . .51• Rear Window Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . . . . .52

• CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52• Automatic Climate Control Overview . . . . . . . . . . . . . . . . . . . . .53• Climate Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . .63• Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . .64• Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

• WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67• Power Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67• Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

• POWER SUNROOF — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . .68• Opening Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69• Closing Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69• Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69• Sunshade Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69• Pinch Protect Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69• Venting Sunroof — Express . . . . . . . . . . . . . . . . . . . . . . . . . .69

17

• Sunroof Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69• Ignition Off Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70• Relearn Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

• HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70• Opening The Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70• Closing The Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

• LIFTGATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71• Power Liftgate — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .71• Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

• INTERNAL EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73• Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73• Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75• Electrical Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . .76• Power Inverter — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .77• Sunglasses Bin Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

• ROOF LUGGAGE RACK — IF EQUIPPED . . . . . . . . . . . . . . . . . . .78• Deploying The Crossbars . . . . . . . . . . . . . . . . . . . . . . . . . . . .78• Stowing The Crossbars . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

18

KEYS

Key FobYour vehicle uses a keyless ignition system. Theignition system consists of a key fob with Re-mote Keyless Entry (RKE) and a START/STOPpush button ignition system. The Remote Key-less Entry system consists of a key fob andKeyless Enter-N-Go feature if equipped.

NOTE:The key fob may not be found if it is located nextto a mobile phone, laptop or other electronicdevice; these devices may block the key fob’swireless signal.

The key fob also includes an emergency key,which stores in the rear of the key fob.

The emergency key allows for entry into thevehicle should the battery in the vehicle or thekey fob go dead. The emergency key is also forlocking the glove compartment. You can keepthe emergency key with you when valet parking.

To remove the emergency key, slide the me-chanical latch at the top of the key fob sidewayswith your thumb and then pull the key out withyour other hand.

NOTE:You can insert the double-sided emergency keyinto the lock cylinders with either side up.

NOTE:In case the ignition switch does not change withthe push of a button, the key fob may have a lowor dead battery. In this situation, a back upmethod can be used to operate the ignitionswitch. Put the nose side of the key fob (sideopposite of the Emergency Key) against theENGINE START/STOP button and push to op-erate the ignition switch.

To Unlock The Doors And LiftgatePush the interior door unlock button on the doorpanel.

Push and release the unlock button on the keyfob once to unlock the driver’s door or twicewithin five seconds to unlock all doors and theliftgate.

All doors can be programmed to unlock on thefirst push of the unlock button. Refer to“Uconnect Settings” in “Multimedia” for furtherinformation.

The turn signal lights will flash to acknowledgethe unlock signal. The illuminated entry systemwill be activated.

1st Push Of Key Fob Unlock Button

This feature lets you program the system tounlock either the driver’s door or all doors on thefirst push of the unlock button on the key fob. Tochange the current setting, refer to “UconnectSettings” in “Multimedia” for further information.

Key Fob

Emergency Key Removal

19

NOTE:If the vehicle is equipped with Passive Entry,refer to “Keyless Enter-N-Go — Passive Entry”located in “Doors” in “Getting To Know YourVehicle” for further information.

To Lock The Doors And LiftgatePush and release the lock button on the key fobto lock all doors and liftgate.

The turn signal lights will flash and the horn willchirp to acknowledge the signal. Refer to“Uconnect Settings” located in “Multimedia” forfurther programmable information.

If the vehicle is equipped with Passive Entry,refer to “Keyless Enter-N-Go — Passive Entry”located in “Doors” in “Getting To Know YourVehicle” for further information.

Vehicles Equipped With Keyless Enter-N-Go— Passive Entry

If one or more doors are open, or the liftgate isopen, the doors will lock. The doors will unlockagain automatically if the key is left inside thepassenger compartment, otherwise the doorswill stay locked.

Replacing The Battery In The Key WithRemote ControlThe recommended replacement battery is oneCR2032 battery.

NOTE:

• Perchlorate Material — special handling mayapply.

• Do not touch the battery terminals that are onthe back housing or the printed circuit board.

1. Remove the emergency key by sliding themechanical latch on the back of the key fobsideways with your thumb and pull the emer-gency key out with your other hand.

2. Separate the key fob halves using the tip ofthe emergency key, a #2 flat blade screw-driver, or a coin and gently pry the two halvesof the key fob apart. Make sure not to dam-age the seal during removal.


1 — Emergency Key Release Button2 — Emergency Key


Separating Case With A Coin

20

3. Remove the battery by turning the backcover over (battery facing downward) andtapping it lightly on a solid surface such as atable or similar and replace the battery. Whenreplacing the battery, match the + sign on thebattery to the + sign on the inside of thebattery clip, located on the back cover. Avoidtouching the new battery with your fingers.Skin oils may cause battery deterioration. Ifyou touch a battery, clean it with rubbingalcohol.

4. To assemble the key fob case, snap the twohalves together.

Programming Additional Key FobsProgramming the key fob may be performed byan authorized dealer.

Request For Additional Remote Controls

NOTE:Only key fobs that are programmed to thevehicle electronics can be used to start andoperate the vehicle. Once a key fob is pro-grammed to a vehicle, it cannot be programmedto any other vehicle.

WARNING!

• Always remove the key fobs from the ve-hicle and lock all doors when leaving thevehicle unattended.

• For vehicles equipped with Keyless Enter-N-Go — Ignition, always remember toplace the ignition in the OFF mode.

Duplication of key fobs may be performed at anauthorized dealer. This procedure consists ofprogramming a blank key fob to the vehicleelectronics. A blank key fob is one that hasnever been programmed.

NOTE:When having the Sentry Key Immobilizer Sys-tem serviced, bring all vehicle keys with you toan authorized dealer.

IGNITION SWITCH

Keyless Push Button IgnitionThis feature allows the driver to operate theignition with the push of a button, as long as thekey fob is in the passenger compartment.

The Keyless Push Button Ignition has threeoperating modes which are labeled and willilluminate when in position. The three modes areOFF, ACC, and ON/RUN.

NOTE:In case the ignition switch does not change withthe push of a button, the key fob may have a lowor dead battery. In this situation, a back upmethod can be used to operate the ignitionswitch. Put the nose side of the key fob (side

Key Fob Battery Replacement

Keyless Push Button Ignition

1 — OFF2 — ACC3 — ON/RUN

21

opposite of the Emergency Key) against theENGINE START/STOP button and push to op-erate the ignition switch.

Ignition Or Accessory On MessageUpon opening the driver’s door when the ignitionis in ACC or ON (engine not running), a chimewill sound to remind you to place the ignition inthe OFF mode. In addition to the chime, theignition or accessory on message will display inthe cluster.

NOTE:With the Uconnect system, the power windowswitches, radio, power sunroof (if equipped),and power outlets will remain active for up to10 minutes after the ignition is cycled to the OFFposition. Opening either front door will cancelthis feature. The time for this feature is program-mable. Refer to “Uconnect Settings” in “Multime-dia” for further information.

WARNING!

• Before exiting a vehicle, always shift theautomatic transmission into PARK and ap-ply the parking brake. Always make surethe keyless ignition node is in the “OFF”mode, remove the key fob from the vehicleand lock the vehicle.

(Continued)

WARNING! (Continued)

• Never leave children alone in a vehicle, orwith access to an unlocked vehicle.

• Allowing children to be in a vehicle unat-tended is dangerous for a number of rea-sons. A child or others could be seriously orfatally injured. Children should be warnednot to touch the parking brake, brake pedalor the gear selector.

• Do not leave the key fob in or near thevehicle, or in a location accessible to chil-dren, and do not leave the ignition of avehicle equipped with Keyless Enter-N-Goin the ACC or ON/RUN mode. A child couldoperate power windows, other controls, ormove the vehicle.

• Do not leave children or animals insideparked vehicles in hot weather. Interiorheat build-up may cause serious injury ordeath.

CAUTION!

An unlocked vehicle is an invitation. Alwaysremove the key fobs from vehicle, place theignition in the OFF position and lock all doorswhen leaving the vehicle unattended.

Dead Key Fob BatteryKey Not Detected Feature

If the ignition position does not change with apush of the ignition button, and the instrumentcluster display message “Key Fob Not De-tected” is being displayed, the key fob may havea low or dead battery. In this situation, a back upmethod can be used to operate the keylesspush button ignition. Put the nose side (sideopposite of the emergency key) of the key fobagainst the keyless ignition push button andpush to operate the ignition. Once the starterengages and the engine starts remove the keyfob from the keyless ignition push button.

Low Or Dead Key Fob Battery StartingProcedure

22

REMOTE START — IFEQUIPPED

How To Use Remote Start

This system uses the key fob tostart the engine conveniently fromoutside the vehicle while still main-taining security. The system has arange of approximately 300 ft(91 m).

NOTE:

• The vehicle must be equipped with an auto-matic transmission to be equipped with Re-mote Start.

• Obstructions between the vehicle and key fobmay reduce this range.

All of the following conditions must be metbefore the engine will remote start:

• Gear Selector in PARK• Doors closed• Hood closed• Liftgate closed• Hazard switch off• Brake switch inactive (brake pedal not

pushed)

• Battery at an acceptable charge level

• System not disabled from previous remotestart event

• Vehicle alarm system indicator flashing• Ignition in STOP/OFF position• Fuel level meets minimum requirement• Vehicle security alarm is not signaling an

intrusion

WARNING!

• Do not start or run an engine in a closedgarage or confined area. Exhaust gascontains Carbon Monoxide (CO) which isodorless and colorless. Carbon Monoxideis poisonous and can cause serious injuryor death when inhaled.

• Keep key fobs away from children. Opera-tion of the Remote Start System, windows,door locks or other controls could causeserious injury or death.

Remote Start Abort Message — IfEquippedThe following messages will display in the in-strument cluster display if the vehicle fails toremote start or exits remote start prematurely:

• Remote Start Aborted — Door Open• Remote Start Aborted — Hood Open• Remote Start Aborted — Liftgate Open

• Remote Start Aborted — Fuel Low• Remote Start Disabled — Start Vehicle To

Reset

The Remote Start Abort message stays activeuntil the ignition is turned to the ON/RUN posi-tion.

To Enter Remote Start ModePush and release the remote start button on thekey fob twice within five seconds. The vehicledoors will lock, the parking lights will flash, andthe horn will chirp twice (if programmed). Then,the engine will start, and the vehicle will remainin the Remote Start mode for a 15-minute cycle.

NOTE:

• If an engine fault is present or fuel level is low,the vehicle will start and then shut down in10 seconds.

• The park lamps will turn on and remain onduring Remote Start mode.

• For security, power window and power sun-roof operation (if equipped) are disabledwhen the vehicle is in the Remote Startmode.

• The engine can be started two consecutivetimes with the key fob. However, the ignitionmust be cycled by pushing the START/STOPbutton twice (or the ignition switch must becycled to the ON/RUN position) before youcan repeat the start sequence for a thirdcycle.

23

To Exit Remote Start Mode WithoutDriving The VehiclePush and release the remote start button onetime or allow the engine to run for the entire15-minute cycle.

NOTE:To avoid unintentional shutdowns, the systemwill disable with a one time push of the remotestart button for two seconds after receiving avalid remote start request.

To Exit Remote Start Mode AndDrive The VehicleBefore the end of 15-minute cycle, push andrelease the unlock button on the key fob tounlock the doors, or unlock the vehicle usingKeyless Enter-N-Go — Passive Entry via thedoor handles, and disarm the vehicle securityalarm (if equipped). Then, prior to the end of the15-minute cycle, push and release the START/STOP button.

NOTE:For vehicles equipped with the Keyless Enter-N-Go — Passive Entry feature, the message“Remote Start Active — Push Start Button” willdisplay in the instrument cluster display until youpush the ignition START button.

Remote Start Comfort Systems — IfEquippedWhen Remote Start is activated, the heatedsteering wheel and driver heated seat featureswill automatically turn on in cold weather. In

warm weather, the driver vented seat feature willautomatically turn on when the remote start isactivated. These features will stay on throughthe duration of Remote Start or until the ignitionswitch is placed in the ON/RUN mode.

NOTE:The Remote Start Comfort System can be acti-vated and deactivated through the UconnectSystem. Refer to “Uconnect Settings” in “Multi-media” for further information on Remote StartComfort System operation.

SENTRY KEYThe Sentry Key Immobilizer system preventsunauthorized vehicle operation by disabling theengine. The system does not need to be armedor activated. Operation is automatic, regardlessof whether the vehicle is locked or unlocked.

The system uses a key fob and a Keyless PushButton Ignition, and a RF receiver to preventunauthorized vehicle operation. Therefore, onlykey fobs that are programmed to the vehicle canbe used to start and operate the vehicle. If aninvalid key fob is used to attempt to start andoperate the vehicle, the system will not allow theengine to crank. If an invalid key fob is used tostart the engine, the system will shut the engineoff in two seconds.

After placing the ignition to the ON/RUN mode,the vehicle security light will turn on for threeseconds for a bulb check. If the light remains onafter the bulb check, it indicates that there is a

problem with the electronics. In addition, if thelight begins to flash after the bulb check, itindicates that someone used an invalid key fobto start the engine. Either of these conditions willresult in the engine being shut off after twoseconds.

If the vehicle security light turns on duringnormal vehicle operation (vehicle running forlonger than 10 seconds), it indicates that there isa fault in the electronics. Should this occur, havethe vehicle serviced as soon as possible by anauthorized dealer.

CAUTION!

The Sentry Key Immobilizer system is notcompatible with some aftermarket remotestarting systems. Use of these systems mayresult in vehicle starting problems and loss ofsecurity protection.

All of the key fobs provided with your newvehicle have been programmed to the vehicleelectronics.

Customer Key ProgrammingProgramming key fobs may be performed at anauthorized dealer.

24

Replacement KeysNOTE:Only key fobs that are programmed to thevehicle electronics can be used to start andoperate the vehicle. Once a key fob is pro-grammed to a vehicle, it cannot be programmedto any other vehicle.

CAUTION!

• Always remove the key fobs from the ve-hicle and lock all doors when leaving thevehicle unattended.

• For vehicles equipped with Keyless Enter-N-Go — Ignition, always remember toplace the ignition in the OFF position.

NOTE:Duplication of key fobs may be performed at anauthorized dealer. This procedure consists ofprogramming a blank key fob to the vehicleelectronics. A blank key fob is one that hasnever been programmed.

When having the Sentry Key Immobilizer Sys-tem serviced, bring all vehicle keys with you toan authorized dealer.

VEHICLE SECURITY ALARM —IF EQUIPPEDThe vehicle security alarm monitors the vehicledoors for unauthorized entry and the KeylessEnter-N-Go — Ignition for unauthorized opera-

tion. While the vehicle security alarm is armed,interior switches for door locks and liftgate re-lease are disabled. If something triggers thealarm, the vehicle security alarm will provide thefollowing audible and visible signals: the hornwill pulse, the park lamps and/or turn signals willflash, and the vehicle security light in the instru-ment cluster will flash.

To Arm The SystemFollow these steps to arm the vehicle securityalarm:

1. Make sure the vehicle’s ignition is placed inthe OFF mode (refer to "Ignition Switch" inthis chapter for further information).

2. Perform one of the following methods to lockthe vehicle:

• Push lock on the interior power door lockswitch with the driver and/or passenger dooropen.

• Push the lock button on the exterior PassiveEntry Door Handle with a valid key fob avail-able in the same exterior zone (refer to "Key-less Enter-N-Go — Passive Entry," located in“Doors” in “Getting To Know Your Vehicle" forfurther information).

• Push the lock button on the key fob.3. If any doors are open, close them.

NOTE:Security System Manual Override

The vehicle security alarm will not arm if youlock the doors using the manual door lockplunger.

To Disarm The SystemThe vehicle security alarm can be disarmedusing any of the following methods:

• Push the unlock button on the key fob.• Grasp the passive entry unlock door handle

(if equipped, refer to "Keyless Enter-N-Go —Passive Entry" located in “Doors” in “GettingTo Know Your Vehicle" for furtherinformation).

• Cycle the vehicle ignition system out of theOFF position.• For vehicles equipped with Keyless Enter-

N-Go — Passive Entry, push the keylessignition button (requires at least one validkey fob in the vehicle).

• For vehicles not equipped with KeylessEnter-N-Go — Passive Entry, insert a validkey into the ignition and turn the key to theON position.

NOTE:

• The driver’s door key cylinder and the liftgatebutton on the key fob cannot arm or disarmthe vehicle security alarm.

• The vehicle security alarm remains armedduring power liftgate entry. Pushing the lift-

25

gate button will not disarm the vehicle secu-rity alarm. If someone enters the vehiclethrough the liftgate and opens any door, thealarm will sound.

• When the vehicle security alarm is armed, theinterior power door lock switches will notunlock the doors.

The vehicle security alarm is designed to protectyour vehicle. However, you can create condi-tions where the system will give you a falsealarm. If one of the previously described armingsequences has occurred, the vehicle securityalarm will arm regardless of whether you are inthe vehicle or not. If you remain in the vehicleand open a door, the alarm will sound. If thisoccurs, disarm the vehicle security alarm.

If the vehicle security alarm is armed and thebattery becomes disconnected, the vehicle se-curity alarm will remain armed when the batteryis reconnected; the exterior lights will flash, andthe horn will sound. If this occurs, disarm thevehicle security alarm.

Rearming Of The SystemIf something triggers the alarm, and no action istaken to disarm it, the vehicle security alarm willturn the horn off after 29 seconds, five secondsbetween cycles, up to eight cycles if the triggerremains active and the vehicle security alarmwill rearm itself.

DOORS

Manual Door LocksThe power door locks can be manually lockedfrom inside the vehicle by using the door lockknob. To lock each door, push the door lockknob on each door trim panel downward. Tounlock the front doors, pull the inside doorhandle to the first detent. To unlock the reardoors, pull the door lock knob on the door trimpanel upward. If the lock knob is down when thedoor is closed, the door will lock. Therefore,make sure the key is not inside the vehiclebefore closing the door.

WARNING!

• For personal security and safety in theevent of an collision, lock the vehicle doorsas you drive as well as when you park andleave the vehicle.

• Never leave children alone in a vehicle, orwith access to an unlocked vehicle.

• Allowing children to be in a vehicle unat-tended is dangerous for a number of rea-sons. A child or others could be seriously orfatally injured. Children should be warnednot to touch the parking brake, brake pedalor the gear selector.

• Do not leave the key fob in or near thevehicle, or in a location accessible to chil-dren, and do not leave the ignition of avehicle equipped with Keyless Enter-N-Goin the ACC or ON/RUN mode. A child couldoperate power windows, other controls, ormove the vehicle.

• When leaving the vehicle, always makesure the keyless ignition node is in the "Off"mode, remove the key fob from the vehicleand lock the vehicle. Unsupervised use ofthe vehicle equipment may cause severeperson injuries and death.

Manual Door Lock Knob

26

Power Door LocksThe power door lock and unlock switches arelocated on each front door panel. Push theswitch to lock or unlock the doors and liftgate.

If the lock knob is down when the door is closed,the door will lock. Therefore, make sure the keyfob is not inside the vehicle before closing thedoor.

NOTE:The key fob may not be able to be detected bythe vehicle keyless-go system if it is located nextto a mobile phone, laptop or other electronicdevice; these devices may block the key fob’swireless signal and prevent the keyless-go sys-tem from starting the vehicle.

If you push the door lock switch while theignition position is in ACC or ON/RUN and thedriver or front passenger’s door is open, thedoors will not lock.

If a rear door is locked, it cannot be opened frominside the vehicle without first unlocking thedoor. The door may be unlocked manually byraising the lock knob.

Keyless Enter-N-Go — Passive EntryThe Passive Entry system is an enhancement tothe vehicle’s Remote Keyless Entry system anda feature of Keyless Enter-N-Go — PassiveEntry. This feature allows you to lock and unlockthe vehicle’s door(s) without having to push thekey fob lock or unlock buttons.

NOTE:

• Passive Entry may be programmed ON/OFF.Refer to “Uconnect Settings” in “Multimedia”for further information.

• If wearing gloves on your hands, or if it hasbeen raining/snowing on the Passive Entrydoor handle, the unlock sensitivity can beaffected, resulting in a slower response time.

• If the vehicle is unlocked by Passive Entryand no door is opened within 60 seconds, thevehicle will re-lock and if equipped will armthe security alarm.

• The key fob may not be able to be detectedby the vehicle passive entry system if it islocated next to a mobile phone, laptop orother electronic device; these devices mayblock the key fob’s wireless signal and pre-vent the passive entry handle from locking/unlocking the vehicle.

• Passive Entry activates illuminated approachfor the time set by the customer (0, 30, 60, or90 seconds), and flashes the turn signallights. Refer to “Uconnect Settings” in “Multi-media” for further information

To Unlock From The Driver’s Side:

With a valid Passive Entry key fob within 5 ft(1.5 m) of the driver’s door handle, grab thedriver’s front door handle to unlock the driver’sdoor automatically. The interior door panel lockknob will raise when the door is unlocked.

NOTE:If “Unlock All Doors 1st Press” is programmed,all doors will unlock when you grab hold of thedriver’s front door handle. To select between“Unlock Driver Door 1st Press” and “Unlock AllDoors 1st Press”, refer to “Uconnect Settings” in“Multimedia” for further information.

Power Door Lock Switches

Grab The Door Handle To Unlock

27

To Unlock From The Passenger Side:

With a valid Passive Entry key fob within 5 ft(1.5 m) of the passenger door handle, grab thefront passenger door handle to unlock all fourdoors automatically. The interior door panel lockknob will raise when the door is unlocked.

NOTE:All doors will unlock when the front passengerdoor handle is grabbed regardless of the driver’sdoor unlock preference setting (“Unlock DriverDoor 1st Press” or “Unlock All Doors 1st Press”).

Preventing Inadvertent Locking Of PassiveEntry Key Fob In Vehicle

To minimize the possibility of unintentionallylocking a Passive Entry key fob inside yourvehicle, the Passive Entry system is equippedwith an automatic door unlock feature, which willfunction if the ignition is OFF.

If one of the vehicle doors is open, and the doorpanel switch is used to lock the vehicle, once allopen doors have been closed, the vehiclechecks the inside and outside of the vehicle forany valid Passive Entry key fob. If one of thevehicle’s Passive Entry key fob is detectedinside the vehicle, and no other valid PassiveEntry key fob are detected outside the vehicle,the Passive Entry System automatically unlocksall vehicle doors and chirps the horn three times(on the third attempt, ALL doors will lock, and thePassive Entry key fob can be locked in thevehicle).

To Unlock/Enter The Liftgate

The liftgate passive entry unlock feature is builtinto the electronic liftgate handle. With a validPassive Entry key fob within 5 ft (1.5 m) of theliftgate, pull the electronic liftgate handle for apower open on vehicles equipped with PowerLiftgate. Pull the electronic liftgate handle and liftfor Manual Liftgate vehicles.

NOTE:If the vehicle is unlocked, the liftgate will openwith the handle and no key fob is required.

To Lock The Liftgate

With a valid Passive Entry key fob within 5 ft(1.5 m) of the liftgate, push the passive entrylock button located to the right of electronicliftgate handle.

NOTE:If “Unlock All Doors 1st Press” is programmed inUconnect Settings, all doors will unlock whenyou push the button on the liftgate. If "UnlockDriver Door 1st Press" is programmed inUconnect Settings, the liftgate will unlock whenyou push the button on the liftgate. For furtherinformation, refer to “Uconnect Settings” in “Mul-timedia”.

To Lock The Vehicle’s Doors

With one of the vehicle’s Passive Entry key fobwithin 5 ft (1.5 m) of the driver or passenger frontdoor handle, push the door handle lock button tolock all four doors and liftgate.

Passive Entry/Lock Button Location

1 — Electronic Release Switch2 — Lock Button Location

Push The Door Handle Button To Lock

28

NOTE:Do NOT grab the door handle, when pushingthe door handle button. This could unlockthe door(s).

NOTE:

• After pushing the door handle button, youmust wait two seconds before you can lock orunlock the doors, using either Passive Entrydoor handle or door handle button. This isdone to allow you to check if the vehicle islocked by pulling the door handle, without thevehicle reacting and unlocking.

• The Passive Entry system will not operate ifthe key fob battery is dead.

• Closeness to mobile devices can have aneffect on the passive entry system.

The vehicle doors can also be locked by usingthe key fob lock button or the lock button locatedon the vehicle’s interior door panel.

Automatic Unlock On Exit Feature —If EquippedIf Auto Unlock is enabled, this feature will unlockall the doors when any door is opened if thevehicle is stopped and in PARK. Refer to“Uconnect Settings” in “Multimedia” for furtherinformation.

Automatic Door Locks — IfEquippedWhen enabled, the door locks will lock automati-cally when the vehicle’s speed exceeds 15 MPH(24 km/h). Auto door lock feature is enabled/disabled in the Uconnect Settings sections inthe radio. Refer to “Uconnect Settings” in “Mul-timedia” for further information.

Child-Protection Door Lock System— Rear DoorsTo provide a safer environment for small chil-dren riding in the rear seats, the rear doors areequipped with Child-Protection Door Lock sys-tem.

To Engage Or Disengage The Child Protec-tion Door Lock System

1. Open the rear door.

2. Insert the tip of the emergency key into thelock and rotate to the lock or unlock position.

3. Repeat steps 1 and 2 for the opposite reardoor.

WARNING!

Avoid trapping anyone in a vehicle in acollision. Remember that the rear doors canonly be opened from the outside with theChild-Protection locks are engaged (locked).

Do NOT Grab The Door Handle When Locking

Child-Protection Door Lock Location

Child-Protection Door Lock Function

29

NOTE:For emergency exit with the system engaged,move the lock knob up (unlocked position), rolldown the window, and open the door with theoutside door handle.

SEATSSeats are a part of the Occupant RestraintSystem of the vehicle.

WARNING!

• It is dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision,people riding in these areas are more likelyto be seriously injured or killed.

• Do not allow people to ride in any area ofyour vehicle that is not equipped with seatsand seat belts. In a collision, people ridingin these areas are more likely to be seri-ously injured or killed.

• Be sure everyone in your vehicle is in aseat and using a seat belt properly.

Manual Adjustment (Front Seats)

WARNING!

• Adjusting a seat while the vehicle is movingis dangerous. The sudden movement ofthe seat could cause you to lose control.The seat belt might not be adjusted prop-erly and you could be injured. Adjust theseat only while the vehicle is parked.

• Do not ride with the seatback reclined sothat the shoulder belt is no longer restingagainst your chest. In a collision you couldslide under the seat belt and be seriouslyor even fatally injured. Use the recliner onlywhen the vehicle is parked.

Manual Front Passenger Seat Forward/Rearward AdjustmentSome models may be equipped with a manualfront passenger seat. The passenger seat canbe adjusted forward or rearward by using a barlocated by the front of the seat cushion, near thefloor.

While sitting in the seat, lift up on the bar locatedunder the seat cushion and move the seatforward or rearward. Release the bar once youhave reached the desired position. Then, usingbody pressure, move forward and rearward onthe seat to be sure that the seat adjusters havelatched.

WARNING!

• Adjusting a seat while driving may be dan-gerous. Moving a seat while driving couldresult in loss of control which could cause acollision and serious injury or death.

• Seats should be adjusted before fasteningthe seat belts and while the vehicle isparked. Serious injury or death could resultfrom a poorly adjusted seat belt.

Adjustment Bar

30

Manual Front Passenger SeatbackAdjustment — ReclineTo adjust the seatback, lift the lever located onthe outboard side of the seat, lean back to thedesired position and release the lever. To returnthe seatback, lift the lever, lean forward andrelease the lever.

WARNING!

Do not ride with the seatback reclined so thatthe shoulder belt is no longer resting againstyour chest. In a collision you could slideunder the seat belt, which could result inserious injury or death.

Front Passenger Seat Fold-Flat Feature —If EquippedTo fold the seatback to the flat load-floor posi-tion, lift the recline lever and push the seatbackforward. To return to the seating position, raisethe seatback and lock it into place.

WARNING!

• Adjusting a seat while the vehicle is movingis dangerous. The sudden movement ofthe seat could cause you to lose control.The seat belt might not be properly ad-justed, and you could be severely injuredor killed. Only adjust a seat while thevehicle is parked.

• Do not ride with the seatback reclined sothat the seat belt is no longer restingagainst your chest. In a collision, you couldslide under the seat belt and be severelyinjured or killed. Use the recliner only whenthe vehicle is parked.

CAUTION!

Do not place any article under a power seator impede its ability to move as it may causedamage to the seat controls. Seat travel maybecome limited if movement is stopped by anobstruction in the seat’s path.

Power Adjustment (Front Seats) — IfEquippedSome models may be equipped with eight-waypower driver and front passenger seats. Thepower seat switches are located on the out-board side of the seat. There are two switchesthat control the movement of the seat cushionand the seatback.

Recline Lever

Fold-Flat Passenger Seat

Power Seat Switches

1 — Seatback Switch2 — Seat Switch

31

Adjusting The Seat Forward Or RearwardThe seat can be adjusted both forward andrearward. Push the seat switch forward or rear-ward. The seat will move in the direction of theswitch. Release the switch when the desiredposition has been reached.

Adjusting The Seat Up Or DownThe height of the seats can be adjusted up ordown. Pull upward or push downward on therear of seat switch, the seat will move in thedirection of the switch. Release the switch whenthe desired position has been reached.

Tilting The Seat Up Or DownThe angle of the seat cushion can be adjusted intwo directions. Pull upward or push downwardon the front of the seat switch, the front of theseat cushion will move in the direction of theswitch. Release the switch when the desiredposition has been reached.

Reclining The SeatbackThe angle of the seatback can be adjustedforward or rearward. Push the seatback switchforward or rearward, the seat will move in thedirection of the switch. Release the switch whenthe desired position is reached.

WARNING!



• Do not ride with the seatback reclined sothat the shoulder belt is no longer restingagainst your chest. In a collision you couldslide under the seat belt, which could resultin serious injury or death.

CAUTION!


Power Lumbar — If EquippedVehicles equipped with power driver or passen-ger seats may also be equipped with powerlumbar. The power lumbar switch is located onthe outboard side of the power seat. Push theswitch forward to increase the lumbar support.Push the switch rearward to decrease the lum-

bar support. Pushing upward or downward onthe switch will raise and lower the position of thesupport.

Power Passenger Seat Adjustment— If EquippedSome models are equipped with a six-waypower passenger seat. The power seat switch islocated on the outboard side of the seat. Theswitch is used to control the movement of theseat and seat cushion.

Adjusting The Seat Forward Or RearwardThe seat can be adjusted both forward andrearward. Push the seat switch forward or rear-ward. The seat will move in the direction of theswitch. Release the switch when the desiredposition has been reached.

Adjusting The Seat Up Or DownThe height of the seats can be adjusted up ordown. Pull upward or push downward on therear of seat switch, the seat will move in the

Power Lumbar Switch

32

direction of the switch. Release the switch whenthe desired position has been reached.

Tilting The Seat Up Or DownThe angle of the seat cushion can be adjusted intwo directions. Pull upward or push downwardon the front of the seat switch, the front of theseat cushion will move in the direction of theswitch. Release the switch when the desiredposition has been reached.

Reclining The SeatbackThe angle of the seatback can be adjustedforward or rearward. Push the seatback switchforward or rearward, the seat will move in thedirection of the switch. Release the switch whenthe desired position is reached.

WARNING!



• Do not ride with the seatback reclined sothat the shoulder belt is no longer restingagainst your chest. In a collision you couldslide under the seat belt, which could resultin serious injury or death.

CAUTION!


Driver Memory Seat — If EquippedThis feature allows the driver to store up to twodifferent memory profiles for easy recall througha memory switch. Each memory profile containsdesired position settings for the driver seat, sidemirrors, and power tilt and telescopic steeringcolumn (if equipped) and a set of desired radiostation presets. Your key fob can also be pro-grammed to recall the same positions when theunlock button is pushed.

NOTE:Your vehicle is equipped with two key fobs, onekey fob can be linked to memory position 1 andthe other key fob can be linked to memoryposition 2.

The memory seat switch is located on thedriver’s door trim panel. The switch consists ofthree buttons:

• The set (S) button, which is used to activatethe memory save function.

• The (1) and (2) buttons which are used torecall either of two pre-programmed memoryprofiles.

Programming The Memory Feature

NOTE:To create a new memory profile, perform thefollowing:

1. Cycle the vehicle’s ignition to the ON/RUNposition (do not start the engine).

2. Adjust all memory profile settings to desiredpreferences (i.e., seat, side mirror, power tiltand telescopic steering column [if equipped],and radio station presets).

3. Push and release the set (S) button on thememory switch.

4. Within five seconds, push and release eitherof the memory buttons (1) or (2). The instru-ment cluster display will display whichmemory position has been set.

Memory Seat Switch

33

NOTE:

• Memory profiles can be set without the ve-hicle in PARK, but the vehicle must be inPARK to recall a memory profile.

• To set a memory profile to your key fob, referto “Linking And Unlinking The Remote Key-less Entry Key Fob To Memory” in thissection.

Linking And Unlinking The Remote KeylessEntry Key Fob To MemoryYour key fobs can be programmed to recall oneof two pre-programmed memory profiles bypushing the unlock button on the key fob.

NOTE:Before programming your key fobs you mustselect the “Memory Linked To FOB” featurethrough the Uconnect system screen. Refer to“Uconnect Settings” in “Multimedia” for furtherinformation.

To program your key fobs, perform the following:

1. Cycle the vehicle’s ignition to the OFF posi-tion.

2. Select a desired memory profile, 1 or 2.

NOTE:If a memory profile has not already been set,refer to "Programming The Memory Feature" inthis section for instructions on how to set amemory profile.

3. Once the profile has been recalled, push andrelease the set (S) button on the memoryswitch.

4. Within five seconds, push and release button(1) or (2) accordingly. “Memory Profile Set”(1 or 2) will display in the instrument cluster.

5. Push and release the lock button on the keyfob within 10 seconds.

NOTE:Your key fobs can be unlinked to your memorysettings by pushing the set (S) button, andwithin 10 seconds, followed by pushing theunlock button on the key fob.

Memory Position Recall

NOTE:The vehicle must be in PARK to recall memorypositions. If a recall is attempted when thevehicle is not in PARK, a message will bedisplayed in the instrument cluster display.

Driver One Memory Position Recall

• To recall the memory settings for driver oneusing the memory switch, push memory but-ton (1) on the memory switch.

• To recall the memory settings for driver oneusing the key fob, push the unlock button onthe key fob linked to memory position 1.

Driver Two Memory Position Recall

• To recall the memory setting for driver twousing the memory switch, push memory but-ton (2) on the memory switch.

• To recall the memory settings for driver twousing the key fob, push the unlock button onthe key fob linked to memory position 2.

A recall can be canceled by pushing any of thememory buttons during a recall (S, 1, or 2), or bypushing any of the seat adjustment switches.When a recall is canceled, the driver’s seat andsteering column (if equipped) stop moving. Adelay of one second will occur before anotherrecall can be selected.

Easy Entry/Exit SeatThis feature provides automatic driver seat po-sitioning to enhance driver mobility when enter-ing and exiting the vehicle.

The distance the driver seat moves depends onwhere you have the driver seat positioned whenyou cycle the vehicle’s ignition to the OFFposition.

• When you cycle the vehicle’s ignition to theOFF position, the driver seat will move about2.4 inches (60 mm) rearward if the driver seatposition is greater than or equal to 2.7 inches(67.7 mm) forward of the rear stop. The seatwill return to its previously set position whenyou cycle the vehicle’s ignition to the ACC orRUN position.

34

• The Easy Entry/Easy Exit feature is disabledwhen the driver seat position is less than0.9 of an inch (22.7 mm) forward of the rearstop. At this position, there is no benefit to thedriver by moving the seat for Easy Exit orEasy Entry.

Each stored memory setting will have an asso-ciated Easy Entry and Easy Exit position.

NOTE:The Easy Entry/Exit feature is not enabled whenthe vehicle is delivered from the factory. TheEasy Entry/Exit feature is enabled (or later dis-abled) through the programmable features inthe Uconnect system. Refer to “Uconnect Set-tings” in “Multimedia”.

Heated Seats — If EquippedOn some models, the front and rear seats maybe equipped with heaters located in the seatcushions and seat backs.

WARNING!

• Persons who are unable to feel pain to theskin because of advanced age, chronicillness, diabetes, spinal cord injury, medi-cation, exhaustion or other physical condi-tion must exercise care when using theseat heater. It may cause burns even at lowtemperatures, especially if used for longperiods of time.

(Continued)


• Do not place anything on the seat or seat-back that insulates against heat, such as ablanket or cushion. This may cause theseat heater to overheat. Sitting in a seatthat has been overheated could causeserious burns due to the increased surfacetemperature of the seat.

Front Heated SeatsThe front heated seats control buttons are lo-cated within the climate or controls screen of thetouchscreen.

You can choose from HI, LO, or OFF heatsettings. The indicator arrows in touchscreenbuttons indicate the level of heat in use. Twoindicator arrows will illuminate for HI, one for LOand none for OFF.

• Press the heated seat button once to turnthe HI setting on.

• Press the heated seat button a secondtime to turn the LO setting on.

• Press the heated seat button a third timeto turn the heating elements off.

If the HI-level setting is selected, the system willautomatically switch to LO-level after approxi-mately 60 minutes of continuous operation. Atthat time, the display will change from HI to LO,

indicating the change. The LO-level setting willturn off automatically after approximately 45minutes.

NOTE:

• Once a heat setting is selected, heat will befelt within two to five minutes.

• The engine must be running for the heatedseats to operate.

Vehicles Equipped With Remote Start

On models that are equipped with remote start,the heated seats can be programmed to comeon during a remote start.

This feature can be programmed through theUconnect system. Refer to “Uconnect Settings”in “Multimedia” for further information.

WARNING!


(Continued)

35



Rear Heated Seats — If EquippedOn some models, the two rear outboard seatsmay be equipped with heated seats. There aretwo heated seat switches that allow the rearpassengers to operate the seats independently.The heated seat switches for each heater arelocated on the rear of the center console.

You can choose from HI, LO, or OFF heat settings.Amber indicator lights in each switch indicate thelevel of heat in use. Two indicator lights willilluminate for HI, one for LO and none for OFF.

Push the switch once to select HI-level heating. Push the switch a sec-ond time to select LO-level heating.Push the switch a third time to shutthe heating elements off.

When the HI-level setting is selected, the heaterwill provide a boosted heat level during the firstfour minutes of operation. Then, the heat outputwill drop to the normal HI-level. If the HI-levelsetting is selected, the system will automaticallyswitch to LO-level after approximately 60 min-utes of continuous operation. At that time, thenumber of indicator lights changes from two toone, indicating the change. The LO-level settingwill turn off automatically after approximately45 minutes.

WARNING!


(Continued)



Front Ventilated Seats — If EquippedLocated in the seat cushion and seat back arefans that draw the air from the passenger com-partment and move air through fine perforationsin the seat cover to help keep the driver andfront passenger cooler in higher ambient tem-peratures. The fans operate at two speeds, HIand LO.

The front ventilated seats control buttons arelocated within the Uconnect system. You cangain access to the control buttons through theclimate screen or the controls screen.

• Press the ventilated seat button once tochoose HI.

• Press the ventilated seat button a secondtime to choose LO.

• Press the ventilated seat button a thirdtime to turn the ventilated seat off.

NOTE:The engine must be running for the ventilatedseats to operate.

Rear Heated Seat Switches

36


On models that are equipped with remote start,the ventilated seats can be programmed tocome on during a remote start.

This feature can be programmed through theUconnect system. Refer to “Uconnect Settings”in “Multimedia” for further information.

60/40 Split Rear SeatSecond Row Fold Flat SeatThe second row seats can be folded flat to carrycargo.

Pull upward on the release lever located on theoutboard side of the seat.

NOTE:You may experience deformation in the seatcushion from the seat belt buckles if the seatsare left folded for an extended period of time.This is normal and by simply opening the seatsto the open position, over time the seat cushionwill return to its normal shape.

Easy Access For Third RowEither side of the rear seat can be tumbledforward to allow passengers to easily access thethird row seats.

1. Pull upward on the release lever to releasethe seat.

2. Tumble the seat forward using the pull straplocated behind the seatback.

Release Lever

Fold-Flat Second Row Seat Release Lever

Tumble Strap

37

WARNING!

Do not drive the vehicle with the second rowseats in the tumbled position. The secondrow seats are only intended to be tumbled forentry and exit to the third row seat. Failure tofollow these instructions could result in per-sonal injury.

To Raise Rear SeatFold the seat rearward to it’s original position,and lock it into place.

WARNING!

Be certain that the seatback is securelylocked into position. If the seatback is notsecurely locked into position the seat will notprovide the proper stability for child seatsand/or passengers. An improperly latchedseat could cause serious injury.

Rear Captain’s Chairs — If EquippedSecond Row Captain Chair Fold Flat SeatsThe second row seats can be folded flat to carrycargo.

Pull upward on the release lever located on theoutboard side of the seat.


Easy Access For Third RowEither side of the rear seat can be tumbledforward to allow passengers to easily access thethird row seats.

Tumbled Second Row

Release Lever

Fold-Flat Second Row Seats

38

1. Pull upward on the release lever to releasethe seat.

2. Tumble the seat forward using the pull straplocated behind the seatback.

WARNING!

Do not drive the vehicle with the second rowseats in the tumbled position. The secondrow seats are only intended to be tumbled forentry and exit to the third row seat. Failure tofollow these instructions could result in per-sonal injury.

3. If your vehicle is equipped with a mini con-sole, there is a stepping pad to allow passen-gers to easily access the third row seats.

To Raise Rear SeatFold the seat rearward to it’s original position,and lock it into place.

WARNING!

Be certain that the seatback is securelylocked into position. If the seatback is notsecurely locked into position the seat will notprovide the proper stability for child seatsand/or passengers. An improperly latchedseat could cause serious injury.

Folding Third RowBoth third row seats can be folded forward toincrease the cargo area. To lower either seat,pull on the release handle located on back of theseat and lower the seat using the pull straplocated next to the release handle.

Release Lever

Tumble Strap

Mini Console Stepping Pad

Release Handles

39

NOTE:The second row seats must be in their fullupright position or tumbled when folding thethird row seats.

To raise the seat, pull the seat toward you usingthe strap located on the back of the seat.


WARNING!

Be certain that the seatback is securelylocked into position. If the seatback is not

(Continued)


securely locked into position the seat will notprovide the proper stability for child seatsand/or passengers. An improperly latchedseat could cause serious injury.

HEAD RESTRAINTSHead restraints are designed to reduce the riskof injury by restricting head movement in theevent of a rear impact. Head restraints shouldbe adjusted so that the top of the head restraintis located above the top of your ear.

WARNING!

• All occupants, including the driver, shouldnot operate a vehicle or sit in a vehicle’sseat until the head restraints are placed intheir proper positions in order to minimizethe risk of neck injury in the event of acrash.

• Head restraints should never be adjustedwhile the vehicle is in motion. Driving avehicle with the head restraints improperlyadjusted or removed could cause seriousinjury or death in the event of a collision.

Supplemental Active HeadRestraints — Front SeatsActive Head Restraints are passive, deployablecomponents, and vehicles with this equipment can-not be readily identified by any markings, onlythrough visual inspection of the head restraint. TheActive Head Restraints (AHR) will be split in twohalves, with the front half being soft foam and trim,the back half being decorative plastic.

When AHRs deploy during a rear impact, thefront half of the head restraint extends forwardto reduce the gap between the back of theoccupant’s head and the AHR. This system isdesign to reduce the risk of injury to the driver orfront passenger in certain types of rear impacts.Refer to “Occupant Restraints” in “Safety” forfurther information.

To raise the head restraint, pull upward on thehead restraint. To lower the head restraint, pushthe adjustment button, located at the base of thehead restraint, and push downward on the headrestraint.

Third Row Folded

Adjustment Button40

For comfort the Active Head Restraints can betilted forward and rearward. To tilt the headrestraint closer to the back of your head, pullforward on the bottom of the head restraint.Push rearward on the bottom of the head re-straint to move the head restraint away fromyour head.

NOTE:

• The head restraints should only be removedby qualified technicians, for service purposesonly. If either of the head restraints requireremoval, see your authorized dealer.

• In the event of deployment of an Active HeadRestraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in“Safety” for further information.

WARNING!

• All occupants, including the driver, shouldnot operate a vehicle or sit in a vehicle’sseat until the head restraints are placed intheir proper positions in order to minimizethe risk of neck injury in the event of acollision.

• Do not place items over the top of theActive Head Restraint, such as coats, seatcovers or portable DVD players. Theseitems may interfere with the operation ofthe Active Head Restraint in the event of acollision and could result in serious injuryor death.

(Continued)


• Active Head Restraints may be deployed ifthey are struck by an object such as ahand, foot or loose cargo. To avoid acci-dental deployment of the Active Head Re-straint ensure that all cargo is secured, asloose cargo could contact the Active HeadRestraint during sudden stops. Failure tofollow this warning could cause personalinjury if the Active Head Restraint is de-ployed.

Head Restraints — Rear SeatsThe head restraints on the outboard seats arenot adjustable. They automatically fold forwardwhen the rear seat is folded to a load floorposition, but do not return to their normal posi-tion when the rear seat is raised. After returningeither seat to its upright position, raise the headrestraint until it locks in place. The outboardhead restraints are not removable.

The center head restraint has limited adjust-ment. Lift upward on the head restraint to raiseit or push downward on the head restraint tolower it.

Active Head Restraint (Normal Position)

Active Head Restraint (Tilted)

41

WARNING!

Sitting in a seat with the head restraint in itslowered position could result in serious injuryor death in a collision. Always make sure theoutboard head restraints are in their uprightpositions when the seat is to be occupied.

NOTE:For proper routing of a Child Seat Tether, refer to“Occupant Restraints” in “Safety” for furtherinformation.

Head Restraint Removal — RearSeatsThe center head restraint can be adjusted whenoccupied, or removed for Child Seat Tethering.To remove the head restraint, raise it as far as itcan go by pulling upward. Then, push the re-lease button at the base of the post while pullingthe head restraint upward. To reinstall the head

restraint, put the head restraint posts into theholes and push downward. Then, adjust thehead restraint to the appropriate height.

WARNING!

• ALL the head restraints MUST be rein-stalled in the vehicle to properly protectthe occupants. Follow the re-installationinstructions above prior to operating thevehicle or occupying a seat.

• Sitting in a seat with the head restraint inits lowered position could result in seriousinjury or death in a collision. Always makesure the outboard head restraints are intheir upright positions when the seat is tobe occupied.

NOTE:For proper routing of a Child Seat Tether, refer to“Occupant Restraints” in “Safety” for furtherinformation.

WARNING!

• A loose head restraint thrown forward in acollision or hard stop could cause seriousinjury or death to occupants of the vehicle.Always securely stow removed head re-straints in a location outside the occupantcompartment.

• ALL the head restraints MUST be rein-stalled in the vehicle to properly protect theoccupants. Follow the re-installation in-structions above prior to operating the ve-hicle or occupying a seat.

Power Folding Third Row HeadRestraintsFor improved visibility when in reverse, the thirdrow head restraints can be folded using theUconnect System.

Press the “Controls” button located on the bot-tom of the Uconnect display.

Press the Headrest Fold button to power foldthe third row head restraints.

Rear Head Restraint

Center Head Restraint Release Button

42

NOTE:

• The head restraints can only be folded down-ward using the Headrest Fold button. Thehead restraints must be raised manuallywhen occupying the third row.

• Do not fold if there are passengers seated inthe third row seats.

STEERING WHEEL

Tilt/Telescoping Steering ColumnThis feature allows you to tilt the steering col-umn upward or downward. It also allows you tolengthen or shorten the steering column. Thetilt/telescoping lever is located below the steer-ing wheel at the end of the steering column.

To unlock the steering column, push the leverdownward (toward the floor). To tilt the steeringcolumn, move the steering wheel upward ordownward as desired. To lengthen or shortenthe steering column, pull the steering wheeloutward or push it inward as desired. To lock thesteering column in position, push the lever up-ward until fully engaged.

WARNING!

Do not adjust the steering column whiledriving. Adjusting the steering column whiledriving or driving with the steering columnunlocked, could cause the driver to losecontrol of the vehicle. Failure to follow thiswarning may result in serious injury or death.

Power Tilt/Telescoping SteeringColumn — If EquippedThis feature allows you to tilt the steering col-umn upward or downward. It also allows you tolengthen or shorten the steering column. Thepower tilt/telescoping steering column lever islocated below the multifunction lever on thesteering column.

To tilt the steering column, move the lever up ordown as desired. To lengthen or shorten thesteering column, pull the lever toward you orpush the lever away from you as desired.

NOTE:For vehicles equipped with Driver Memory Seat,you can use your key fob or the memory switchon the driver’s door trim panel to return thetilt/telescopic steering column to pre-programmed positions. Refer to “Driver MemorySeat” in this section for further information.

WARNING!

Do not adjust the steering column whiledriving. Adjusting the steering column whiledriving or driving with the steering columnunlocked, could cause the driver to losecontrol of the vehicle. Failure to follow thiswarning may result in serious injury or death.

Tilt/Telescoping Lever

Power Tilt/Telescoping Steering Column

43

Heated Steering Wheel — IfEquippedThe steering wheel contains a heating elementthat helps warm your hands in cold weather. Theheated steering wheel has only one temperaturesetting. Once the heated steering wheel hasbeen turned on, it will stay on for an average of80 minutes or more before automatically shut-ting off. This time will vary based on environ-mental temperatures. The heated steeringwheel can shut off early or may not turn on whenthe steering wheel is already warm.

The heated steering wheel control button islocated within the Uconnect system. You cangain access to the control button through theclimate screen or the controls screen.

• Press the heated steering wheel buttononce to turn the heating element on.

• Press the heated steering wheel button asecond time to turn the heating element off.

If your vehicle is equipped with automatic tem-perature controls with an integrated centerstack, or manual temperature controls, you’llfind the heated steering wheel switch on theswitch bank below the radio screen.

NOTE:The engine must be running for the heatedsteering wheel to operate.


On models that are equipped with remote start,the heated steering wheel can be programmedto come on during a remote start through theUconnect system. Refer to “Uconnect Settings”in “Multimedia” for further information.

WARNING!

• Persons who are unable to feel pain to theskin because of advanced age, chronicillness, diabetes, spinal cord injury, medi-cation, exhaustion, or other physical condi-tions must exercise care when using thesteering wheel heater. It may cause burnseven at low temperatures, especially ifused for long periods.

• Do not place anything on the steeringwheel that insulates against heat, such asa blanket or steering wheel covers of anytype and material. This may cause thesteering wheel heater to overheat.

MIRRORS

Inside Day/Night Mirror — IfEquippedThe mirror head can be adjusted up, down, left, andright for various drivers. The mirror should be adjustedto center on the view through the rear window.

Headlight glare from vehicles behind you can bereduced by moving the small control under themirror to the night position (toward the rear ofthe vehicle). The mirror should be adjusted whileset in the day position (toward the windshield).

Automatic Dimming Mirror — IfEquippedThe mirror head can be adjusted up, down, left,and right for various drivers. The mirror shouldbe adjusted to center on the view through therear window.

This mirror automatically adjusts for headlightglare from vehicles behind you.

NOTE:The Automatic Dimming Mirror feature is dis-abled when the vehicle is in REVERSE toimprove rear view viewing.

Adjusting Rearview Mirror

44

You can turn the feature on or off by pushing thebutton at the base of the mirror. A light in thebutton will illuminate to indicate when the dim-ming feature is activated.

Outside MirrorsTo receive maximum benefit, adjust the outsidemirror(s) to center on the adjacent lane of trafficwith a slight overlap of the view obtained on theinside mirror.

WARNING!

Vehicles and other objects seen in an outsideconvex mirror will look smaller and fartheraway than they really are. Relying too muchon side convex mirrors could cause you tocollide with another vehicle or other object.Use your inside mirror when judging the sizeor distance of a vehicle seen in a side convexmirror.

Outside Mirrors Folding FeatureAll outside mirrors are hinged and may bemoved either forward or rearward to resist dam-age. The hinges have three detent positions:

• Full forward position• Full rearward position• Normal positionOutside Automatic Dimming Mirrors— If EquippedThe outside mirrors will automatically adjust forglare from vehicles behind you. This feature iscontrolled by the inside automatic dimming mir-ror. The mirrors will automatically adjust forheadlight glare when the inside mirror adjusts.

Power MirrorsThe power mirror switch is located on the driv-er’s side door trim panel.

The power mirror controls consist of mirrorselect buttons and a four-way mirror controlswitch. To adjust a mirror, push the mirror selectbutton for the mirror that you want to adjust.Using the mirror control switch, push on any ofthe four arrows for the direction that you wantthe mirror to move.

Power mirror preselected positions can be con-trolled by the optional Memory Seat Feature.Refer to “Driver Memory Seat” in “Getting ToKnow Your Vehicle” for further information.

Heated Mirrors — If Equipped

These mirrors are heated to melt frostor ice. This feature will be activatedwhenever you turn on the rear windowdefroster (if equipped). Refer to “Cli-

mate Controls” in “Getting To Know Your Ve-hicle” for further information.

Automatic Dimming Mirror

Power Mirror Switch

1 — Mirror Direction Control2 — Mirror Selection

45

Tilt Side Mirrors In Reverse(Available With Memory Seat Only)— If EquippedTilt Side Mirrors In Reverse provides automaticoutside mirror positioning which will aid thedriver’s view of the ground rearward of the frontdoors. Outside mirrors will move slightly down-ward from the present position when the vehicleis shifted into REVERSE. Outside mirrors willthen return to the original position when thevehicle is shifted out of REVERSE position.Each stored memory seat setting will have anassociated Tilt Side Mirrors In Reverse position.

NOTE:The Tilt Side Mirrors In Reverse feature is notturned on when delivered from the factory. TheTilt Side Mirrors In Reverse feature can beturned on and off using the Uconnect System.Refer to “Uconnect Settings” in “Multimedia” forfurther information.

2018 Dodge Durango Owner's Manual · INTRODUCTION Dear Customer, congratulations on selecting your...

Documents

Transcript of 2018 Dodge Durango Owner's Manual · INTRODUCTION Dear Customer, congratulations on selecting your...