lancasterpartsandequipment.com

(717) 299-3721

AFTER MARKET PARTS CATALOG

2008 Horseshoe RoadLancaster, PA 17602

ALSO SEE: OUR HAMMER MILLS P. 2 & USED EQUIPMENT P. 53

2 0 1 42008 Horseshoe RoadLancaster, PA 17602

(717) 299-3721 NON-PROFITORGANIZATION

U.S. POSTAGE PAIDLEBANON, PA

PERMIT NO. 146

Where Quality and Integrity IS NEVER IN QUESTION

Hammer Mills production will vary depending on 3 factors; Moisture in grain, Size of Screen and Horse Power.

Example; Moisture of 25 to 28%Screen Size of 5/16”Horse Power of 200, Will produce 1 ton a minute.

Rear discharge with bagger hook up. You connect Bagger to this unit then use one tractor to run both hammer mill and bagger.

4000 SERIES BLOWER OUTHook up to your silo and grind corn. Will fill up to 90ft. with a 200 horse tractor

4000 SERIES REAR DISCHARGE

Why pay the mill when you can own it ?OWN THE MILL.

Here at Lancaster Parts and Equipment we are taking eight row heads and converting them to four row. This gives us many extra parts to offer you along with quality rebuilt four row heads. Also.....ask about our inventory of quality rebuilt gear boxes and head parts.

John Deere® 684/ Kemper 330

Check out our selection of usedKemperTM ChampionTM 3000 Heads!

5

717-299-3721

Table of ContentsJohn Deere® 5000 Series Harvester Parts*........................6 - 22John Deere® 6000 Series Harvester Parts*......................23 - 32630A-B + 640A-B Parts*......................................................33 - 34John Deere® 666 & 664 Corn Head*.................................. 36 - 37John Deere® 4 Row (conversion Head)*.............................38 - 39John Deere® 2 & 3 Row (conversion Head)*..............................40New Holland® 2-row 824 Corn Head*........................................41Misc. Hay Head Teeth.................................................................42New Holland® FX parts*.......................................................42 - 43New Holland® 360N Gathering Chain..........................................44New Holland® 360N Parts* & Adapters................................44 - 45New Holland® 40 Blower Parts*...........................................46 - 47Cup Paddles - New Holland® 900 & FP Parts*...................48 - 49Blower Bands..............................................................................49676 Adapter Plates......................................................................50Header Drives..............................................................................51KemperTM 4500 & J.D. 676 Parts*..............................................52Spouts.........................................................................................53KemperTM ChampionTM 3000 Parts*....................................54 - 55Bale Grabber ..........................................................................56

*Replacement parts made to meet or exceed the quality and durability of the original equipment

Lancaster Parts and Equipment makes it their mission each day to produce quality equipment. When it comes to our customers, we are dedicated to providing them with only the best farm equipment that Lancaster County has to offer. If you’re searching for harvesters, hammer mills, or after market parts for various pieces of farm equipment, rest assured that when you buy from Lancaster Parts and Equipment, you’re guaranteed a piece of equipment that will last for years to come.

Top Left to Right, Bryant Glick, Jason King, Nathan Glick, Omar Smucker, Wilmer Glick, Daniel Smucker, &Joe FisherBottom (Left to Right) Jesse Stoltzfus, Whipper (the dog), Darryl Martin, Zachary Clegg, Dale Metz, & Sam Lapp.

Lancaster Parts and Equipment began in March of 1965 as Lancaster Silo by Paul S. Smucker. We have been dedicated to providing our customers with the highest level of service and quality of products at affordable prices. In Dec. of 2013, the company changed hands to Paul’s son, Omar B. Smucker, and the company’s name was changed to Lancaster Parts & Equipment Inc.

In the 1990’s, Lancaster Parts and Equipment started building kernel processors. Then, in 1995, we went from building roller mills to manufacturing hammer mills. Today, we produce quality hammer mills and a large selection of aftermarket parts for a variety of farm equipment. Years of experience and a quality product are what you can count on when you choose Lancaster Parts and Equipment.

a little about us...

Claas® and Lexion® are registered trademarks of Claas KGaA, MBH • John Deere® and JD® are registered trademarks of Deere & Company • Case®, Case IH® and New Holland are registered trademarks of CNH America, LLC • NHTM is a trademark of CNH America, LLC • KemperTM & ChampionTM are trademarks of Maschinefabrick Kemprt Gmbh

The Crew!

Lancaster Parts and Equipment strives to be the best in the business. Building on our already strong reputation, we are always on the lookout for ways to improve and give our customers an even better experience with our farm equipment. We look forward to meeting all your needs.

Mission and Vision

Lancaster Parts & Equipment2008 Horseshoe Rd Lancaster PA 17602

6 7

717-299-3721

111121

32

1912

26

3

58

2021

33

33

20

25

27

24

23

22

10

29

7

1615

14

18

4

1

28

6

29

29

35

34

17

31

30

25

26

19

111121

32

1912

26

3

58

2021

33

33

20

25

27

24

23

22

10

29

7

1615

14

18

4

1

28

6

29

29

35

34

17

31

30

25

26

19

JD® 5000 K.P. Parts

36

We do complete rebuilds on these processors.

If you don’t see the part you need, give us a call, we probably have a new or used one in stock.

JD® 5000 K.P. PartsPart # DESCRIPTION

1 LAE41922 $32.49 • T Handle Holder2 LZ11242 $24.0 • T Handle3 SP186 $9.59 • Heavy Duty Spring4 LE69927 $10.99 • Idler Holder Bracket Top5 LE69928 $10.89 • Idler Holder Bracket Bottom6 LE69438 $8.29 • Eyebolt7 SP210 $21.99 • Shield Mounting Bracket #AE443198 SP212 $156.99 • Belt Shield9 SP213 $10.89 • Pin10 SP217 $30.99 • Pin Handle11 AE42998 $56.99 • Core Bearing12 SP190 $2.59 • Bolt14 SP189 $4.99 • Pulley Cap15 SP193 $145.99 • 2 Grove Pulley16 SE17340 $9.99 • Seal (JD Pulley Only) [1.75x2.44]16 17392 $7.89 • Seal (LSC Pulley Only) [1.75x2.51]17 LAE41126 $50.00 • Idler Arm18 SP194 $49.99 • Bearing Hub19 SP152 $6.75 • 4 Hole Bearing Plate20 SP153 $11.49 • 1-3/4” Collar21 AE46565 $164.99 • Top Bearing Kernel Processor 22 SP132 $973.50 • Lower Roll23 SP150 $973.50 • Top Roll24 SP143 $9.99 • Collar25 AE45398 $179.99 • Bottom Roller Bearing26 SP128 $36.99 • Adjuster Stud (LSC Stand. Thread)27 SP135 $2.49 • 1/4” Slide Block Shim28 SP134 $4.99 • .025” Slide Block Shim29 SP142 $5.69 • 4” Shaft Washer30 SP119 $39.99 • Roll Stop (Left Hand)31 SP117 $39.99 • Roll Stop (Right Hand)32 SP137 $34.99 • Lower Bearing Support 33 SP138 $21.99 • Lower Roller Spring34 SP167 $44.99 • Ider Pulley

35 SP168 $99.99 • Idler Arm (drive Side)36 LS708520 $252.49 • Idler Pulley Assembly

8 9

717-299-3721

#1 LAE42157Single Auger Housing

Fits JD 5000 Series K.P.$804.99

#2 AE45967Cleanout Door

$28.99 #3 LAE42460-H

Housing$54.99

#3a AE37057Hex Bearing

$59.99#4 LAE42158

Front Bearing Mount$184.99

#5 LAE45495K.P. Auger

*Spline Hub not included$709.99

#6 LAE42176Gearbox Mounting Plate

$124.49#7 LS42157

Single Auger Chute Housing Liner$69.99

#8 LE73996Spline Hub

$81.99

Part # DESCRIPTION

1 LS70248 $2149.99 K.P. Auger Gear Box

2 LE69333 $178.99 Gear Box Shaft

3 JD8194 $14.99 Gear Box Bearing

4 JD8230 $8.99 Gear Box Bearing Race

5 AM1091T $20.99 Gear Box Seal

6 LM44073 $13.89 Spring

7 Z11242 $73.99 T Handle

8 LE69438 $8.29 Adjuster Bolt

9 LAH66202 $24.49 Idler Pulley

10 LAE41922 $32.49 T Handle Holder

KP5000KIT-AUGK.P. With

Single Auger TunnelAnd Gear box

$9,800.00

JD® 5000 K.P. Parts

JD® 5000 K.P. Gear Box

8

7

12

3a3

LAE42460Bearing & Housing

$104.99

Part# Price Description Part# Price Description1 LAE40530 $309.99 Gear Box Housing 14 LE63258 $68.09 Gear 15 Tooth Hex

2 LE67112 $24.99 Bolt On Plate 15 LAE33741 $350.00 Auger

3 LS5010 $3.89 Door Hinge 16 LE56075 $76.99 Top Plate

4 LS5009 $59.99 Sprocket 17 LE56383 $63.99 Small Top Discharge Plate

5 LE58313 $49.99 Gear Box Wear Plate 18 LE63911 $122.46 Bottom Plate

6 LE58255 $35.99 Front Left Side Panel 19 LE63909 $55.98 Rear Bearing Plate

7 LE58254 $32.99 Front Right Side Panel 20 FB-32255 $3.10 Three Hole Bearing Flange

8 LS5007 $64.99 Front RT Side Mid Panel 21 LS5019 $27.69 1” Hex Bearing

9 LE52452 $6.99 Adjustable Axle Plate 22 LE63908 $26.10 Bottom Discharge Plate

10 LE49755 $65.99 Front Left Side Mid Panel 23 LE50622 $5.50 Pin Hookup Plate

11 LE59886 $69.99 Front Top Plate 24 LE48543 $55.50 Discharge & Hookup Plate

12 LE56079 $86.99 Right Side Plate 25 SP229 $8.37 1” Strap

13 LE63910 $109.99 Left Side Plate 26 LS50098 $41.48 1” Hex Shaft

Double Auger Haylage Tunnel

LS70025Double Auger Tunnel

Haylage Complete $2,200.00

LAE42157-comSingle Auger Tunnel

w/ all components Shown$2,200.00

LAE42157GSingle Auger Tunnel

w/ all components Shown + Gear box$4349.99

11

717-299-3721

10

11

10

13

2215

7 2221

6

1420

4

19

3

17

2

98

10818

16

1211

15

13

11

10

13

2215

7 2221

6

1420

4

19

3

17

2

98

10818

16

1211

15

13

Part # DESCRIPTION Part # DESCRIPTION1 AT410C $142.50 Back bearing Plate 12 24H1534 $.75 Shim Washer

2 AT413C $272.00 Front Grearbox 13 CA24430 $80.92 Gear

3 LAE44941 $600.00 Auger 14 AT433 $12.25 Strap for blower

4 AT421C $580.00 Main Auger Housing 15 AT432 $22.50 Gearbox Lid

5 AT415 $8.50 Hookup Tab 16 AT437 $12.64 RH Filler Plate

6 AT434 $29.50 Wear Plate (Top) 17 AT436 $11.55 LH Filler Plate

7 AT435 $42.50 Wear Plate (Bottom) 18 AT427 $16.25 RH Feed Guide

8 H135410 $3.96 Bearing Flange 19 AT426 $16.25 LH Feed Guide

9 LAE37997 $102.38 Hex Shaft 20 AT414 $28.00 Blower Plate

10 AE37057 $51.00 Hex Bearing 21 AT411 $34.99 Cleanout Lid

11 LAE42460 $104.99 Hex Bearing & Housing 22 5071A52 $24.60 Pull-Action Latch

Single Auger Haylage TunnelLAE43928

Single Auger Tunnel Haylage, Complete

$2,400.00

1

2

4

3

1

2

4

3

Part # DESCRIPTION

1 LAE35570 $59.99 3/16” Thick Deflector PlatePrevents K.P. from Choking Up

2 LAE38618 $65.99 Support Plate

3 LAE40698 $174.99 Cutter Head Door

4 LE66518 $118.99 Cutter Head Sliding Door

Part # DESCRIPTION

1 LAE31927 $30.99 • Shield Pin

2 LAE41322 $68.99 • Door Shield

3 LAE45622 $157.99 • Shield

4 LAE45943 $50.99 • Support Bracket For Slip Clutch Shield• Fit JD 5720, 5730, 5820, 5830

5 LAE45942 $211.99 • Shield• Fits All 5000 Series

6 LAE45836 $206.99 • Top Shield Cutter Head

7 LAE44516 $109.99 • Front Hydraulic Shield

5000 Series Cutter Head Shields

2

7

6

4

13

5

2

7

6

4

13

5

2

7

6

4

13

5

2

7

6

4

13

5

5000 Series Shields

LP001050K5000 Series Wet Line Kit

Includes, Valve, Lever, Controls, Hoses & Fittings.(Will double dumping speed)

$700.00

Dump Wagon Valve

12 13

717-299-3721

Part # DESCRIPTION

5 LAE43635$842.00 W/O Teeth$1050.00 With Teeth & Bearings

Upper Front Feed Roll With Metal DetectorStraight tooth design

5a LAE43635T $35.00 ea. Teeth for Upper Front Feed Roll (use w/ LAE43635) need 8

5 LAE43198 $535.00 Upper Front Feed Roll Without Metal DetectorStraight tooth design

5b LAE43635T $22.50 ea. Teeth for Upper Front Feed Roll (no Metal Detector) need 8

5 LAE43198S $934.99 Upper Front Feed Roll Without Metal DetectorStandard tooth design (See pic Above)

5c LAE43635S $33.50

6 LE72037 $107.00 Shaft to fit Upper Feed Roll - 30.1/2” long X 1.3/8”

7 JD9865 $9.99 Upper Front Feed Roll Bearing

8 LE53699 $3.55 Upper Front Feed Roll Seal

9 AE37101 $399.99 Upper Rear Feed Roll

10 LE72352 $43.50 Shaft, to fit Upper Rear Feed Roll

11 JD9438 $39.99 Feed Roll Lift Arm Bearing

12 AE40254 $225.99 Left Hand Feed Roll Lift Arm - Includes Bearing

13 AE40253 $172.99 Right Hand Feed Roll Lift Arm - Includes Bearing

5000 Series Upper Feed Rolls

Bolt On Sprocket to fit either Style upper feed roll

1

4

3

2

5

6

7

1

4

3

2

5

6

7

5000 Series A.C. Parts

Part # DESCRIPTION14 LE72817 $21.99 Support Strap Upper Rear Feed Roll

15 LE72818 $24.99 Support Strap Upper Rear Feed Roll

16 LE55609 $7.99 Washer Upper Rear Feed Roll

17 Z67236 $59.99 Feed Roll Lift Arm Spring LZ67236

18 LE82550 $13.99 Eye Bolt

19 E48604 $55.40 Upper Feed Roll Drive Slip Clutch Drive Sprocket -To fit all 5440,5460,5720,5730,5820 & 5830 SN. 740001 & Before

19a LE75928 $79.99 Upper Feed Roll Drive Slip Clutch Drive Sprocket -To fit all 5440,5460,5720,5730,5820 & 5830 SN. 740001 & After

v

#3 SE501460New Nippondenso Replacement Compressor, Without Manifold

TY6626, TY6766, RE125513, SE501460, SE501464

$304.99

#1 AH87966Condenser

Fits 5830, 5730,5820, 5720

$279.99

#4 LAH116744Compressor mount-

ing bracket$40.99

#2 LE75266Condenser Bracket

$18.99

#5 LE74160Compressor mount-

ing bracket$15.99

#7 LH87092Mounting Bracket

$22.99

#6 AT162848Receiver Drier w/ Oring,

& sight glassAT162848, AT125596

$40.99

LAE34867Universal Joint Yoke and Sprocket for top feedroll

drive$95.75

15

717-299-3721

15

Part # DESCRIPTION

1 14H1020 $8.99 • Castle nut

2 LE62417 $62.99 • Trunnion W/ 3/4” left hand Treads

3 E71781 $48.99 • Shear Bar Adjuster Bolt

4 LE72135-R $67.99 • RH Shear Bar Adjuster Lever RH Outside

5 LE72135-L $67.99 • LH Shear Bar Adjuster Lever LH Outside

6 E71782 $.59 • Spring Pin

7 E65425 $14.99 • Pin

8 E73661 $14.99 • Pin with hex

7

9 10

2

14

4

54

4

8

12

3

1

13

6

11

4

7

9 10

2

14

4

54

4

8

12

3

1

13

6

11

4

5000 Series Lower Feed Rolls

Part # DESCRIPTION

1 LAE35423 $340.00 Lower Front, Feed Roll with1” Hex shaft

1a LAE37237 $340.00 Lower Front, Feed Roll with 1-1/4” Hex bore

1b LAE37238 $11.25 ea. Replaceable Cross Bars for, LAE35423 & LAE37237, 8 required

2 LAE38058 $50.75 Wear Plate, Right Side

3 LAE42646 $929.99 Lower Front, Feed Roll With Metal Detector

4 LS5019 $27.69 Bearing 1” Hex Bore

4a AE46957 $67.99 Bearing 1-1/4” Hex Bore

5 AE37068 $158.00Smooth feed roll, lower rearTo fit early 5000 series with 1” hex shaft

5a E62113 $45.00

Shaft, smooth feed rollTo fit early 5000 series withreplaceable 1” hex shaft 27-3/4” x 1” Hex shaft

5b LAE42180 $270.00Smooth feed roll, lower rearTo fit 5440 and 5460 with factoryDura-drumTM cutterhead before 1984

5c LAE50029 $280.00Smooth feed roll, lower rearTo fit 5720 & 5820 seriesand all 5730 & 5830 series

6 LE64565 $63.75 1-1/4” Hex 27-9/16” Long

5000 Series Lower Feed Rolls

Part # DESCRIPTION

7 LE48605 $35.48 Lower feed roll drive slip clutch sprocket • To fit all 5200, 5400, 5440, 5460 , 5720, 5820, 5730 & 5830 harvesters SN. 740000 & before

8 LE48802 $45.99 Smooth Roll Cleaner

9 LE68041 $9.99 Support Strap

10 LE71828 $6.50 Support Shims, Takes 12

11 LAE38057 $51.99 Wear Plate, Left Side

12 LAE42697 $72.99 Lower Front, Feed roll bearing With Metal Detector

13 LS5032 $49.99 Front cutterhead frame repair (must cut out a section of frame and weld this part in.) Left Hand side

14 LS5033 $49.99 Front cutterhead frame repair (must cut out a section of frame and weld this part in.) Right Hand side

5000 Series Shear Bar Adj.

AE44648Muffler

fits 5830, 5820 & 5400$556.25

42

1

8

5

3

7

6

42

1

8

5

3

7

6

16 17

717-299-37215000 Series Cutter Head

3

1

7

9

12

11

10

4

2

86

5

3

1

7

9

12

11

10

4

2

86

5

13 12

291

27

9

10

2 3

8

23

4

11

6

15

24 2524

28

16

14

17

5

24

26

25

21

24

722

18

20

19

19

2013 12

291

27

9

10

2 3

8

23

4

11

6

15

24 2524

28

16

14

17

5

24

26

25

21

24

722

18

20

19

19

20

We also have rebuild or used gear boxes in stock!

Call for pricing

Part # DESCRIPTION1 LE66827 $300.00 • Shaft for Electric Clutch2 AT13161 $6.10 • Seal3 JD8861 $13.10 • Needle Bearing4 JD8884 $15.88 • Needle Bearing (cap)5 LAE46295 $190.00 • Shaft6 JD9863 $12.22 • Needle Bearing (cap)7 AE71361 $300.00 • Shaft (attachment drive)

Part # DESCRIPTION

1 LAE38694 $370.00 Bearing & Housing

2 LJD9307 $160.99 Bearing Asem. Only

3 LAE44466 $203.99 Shear Bar Kit

4 LAE46064 $46.99 Sharpening Stone

5 LE83035 $.60 Knife Bolt - 120 Per Drum

6 LE66536 $4.59 Knife Strap - 40 Per Drum

7 LE66678 $11.99 Knife - 40 Per Drum

8 LE66537 $5.79 Nut Bar - 40 Per Drum

9 LAE45060 $3179.99 Cutter head Drum (Only)

10 LAE36839 $25.99 Feed Roll Drive coupling sprocket - Weld on Sprocket

11 LE65763 $395.99 K. P. drive pulley mounts on cutter head pulley. (Bolts Included)

12 AE39804 Call

5000 Series Misc. Parts

Part # DESCRIPTION8 JD8819 $15.88 • Needle Bearing9 AE38859 $71.21 • 21 Tooth Sprocket (#60 chain)9 AE37412 $90.66 • 16 Tooth Sprocket (#80 chain)10 E53699 $6.40 • Seal11 AE39768 Call • Gear Box Housing (Big Half)12 AE47004 $1271.29 • Elec Coil13 LAE35446 $58.99 • Elec Clutch Armature Pc14 E64810 $329.99 • Gear15 E66613 $608.68 • Gear16 E66616 $492.26 • Gear17 AE39971 $582.67 • Gear18 AE44867 Call • Used Housing19 SE12325 $8.99 • Seal [1.25x1.63]20 NB-2016D $11.99 • Needle Bearing BH-2016 D21 FH312157 $3.99 • Shim22 AE35505 Call • Drive Sprocket23 E15476 $3.99 • Shim24 E36512 $10.00 • Bearing race25 JD9847 $2.70 • Thrust Bearing26 E50958 $12.97 • Pin27 E32891 $3.99 • Shim28 E66752 $2.75 • Spacer29 JD8675 $103.82 • Bearing

18 19

717-299-3721

Part # DESCRIPTION

1 LAS20 $469.99 Motor/Actuator Also Fits 6000 Series Spouts

2 LAS06 $14.99 Spring

3 LAS02 $355.99 Middle Section (Short)

3A LAS02A $360.99 Middle Section (Long)

4 LAS07 $54.99 Middle Deflector

5 LAS08 $92.46 End Deflector

6 LAS22 $35.99 Adjuster Rod (Short)

6A LAS22L $36.99 Adjuster Rod (Long)

7 LAS19 $199.99 Hyd. Cylinder

8 LAS12 $77.99 Replacement Cover

9 LAS13 $27.60 Side Spout Liner (bottom)

10 LAS14 $26.50 Side Spout Liner (top)

11 LAS24 $29.99 Auxiliary Light

12 LAS18 $15.00 Cleanout Hole Cover

13 LAS21 $85.99 Cylinder Motor Mount

14 LAS03 $27.50 Strap W/5 Holes

15 LAS04 $9.99 Strap 1’’ Wide (13’’ Long)

16 LAS05 $9.99 Strap 1” Wide (19’’ Long)

17 LAS09 $8.99 3 Hole Bracket

5000 Series Adj. Spout

• Kit includes Hyd. deflector motor• Ideal for loading Trucks or Wagons from rear or side• Back and Side Replacement Wear Plates• Spout will go up & down 60°• We also offer a longer center section

(Great for loading trucks)

8

7

12

9

1716

11

10

6

1

13

142

15

4 5

3

8

7

12

9

1716

11

10

6

1

13

142

15

4 5

3

$2,500.00

order #LS70165

*will also need 20” spout extension (LAE37337) if not already on harvester

Fully adjustable spout for the John Deer 5000

series Harvester

5000 Series Misc. Parts

LE73887Draw Bar

Fits All 5000 Series$114.99

LAE47021Weight Holder

$84.99

LAE46263Big Belt Shield

Fits 5000 Series.Quick pins included.

$236.99

LE36223Top Head Pin

Fits 5000 Series$11.98

LE42792Bottom Head Pin

$16.00

LAE3733720” Spout Extension, W/clean out

Fits JD 5000 Series & LSC Gooseneck, 20” Long

$276.99*Call for used 10” 20” and 30” ext.LS70965

Hanger Pin 3/4 x2 1/2

$9.99

4

3

6

7

2

81

5

4

3

6

7

2

81

5Replacement Spout for John Deere®

5000 Series

LE674024 wheel drive Hyd.

mount$36.99

$875.00order #

LS70155

Part # DESCRIPTION1 SPR6.5 $10.60 SPRING

2 LS1132C $532.30 SPOUT BASE

3 LS1135 $21.99 TOP WEAR PLATE

4 LS1136 $22.99 BOTTOM WEAR PLATE

5 LS1137 $24.99 SPOUT DEFLECTOR

6 LS1138 $53.99 BACK LINER

7 LS1139 $7.99 CLEAN OUT DOOR

8 LS1140 $265.31 UPPER SPOUT

20 21

717-299-3721

#1 LAE35950Outside Blower Panel

$131.99#2 LAE36535

Top Blower Band$96.99

#3 LAE45967Clean Out Door

$20.99#4 LE56053

Ring Gear$120.99

#5 LE58022Ring Gear Plate

$$10.99 ea.#6 LE53589

Shim$4.99

#7 LE78174Rear Blower Band

$112.99#8 LAE45920Spout Adapter

Made Out of 1/4” Steel$272.99

#9 LAE28998Inside Blower Panel

$125.99#11 LAE33650CCupped Paddle

Improves Blowing$34.99

#12 LE55570Paddle Strap

$5.99#13 LE55571-5P

5 Paddle Fan Angle$29.99

14

6

13

16

12

17

15

9

7

18

12

211

3

8

1

10

4

5

14

6

13

16

12

17

15

9

7

18

12

211

3

8

1

10

4

5

LS490275Five Paddle Kit. Includes

5 Cupped Paddles$380.00

#15 LE49027

4 Paddle Fan Center$72.99

#16 LE55571Fan Angle

$22.99#17 LAE42484K.P. Drive Pulley

$250.00

#18 LAE42319

Fan Pulley (Used only)Call for Availability

#191½” x ½” short shoulder carriage

bolt (need 3 per paddle)$.62ea.

#20 ½” Lock nut

$.18ea.

#14 LAE33650 Fan Paddle

$23.99

5000 Series Blower PartsLE49027-5P

5 Paddle Center Plate Only$120.00

#1 LAE35686Support

Call#2 LAE44484

Shaft$225.00

1 LAE30020 $155.36 Clutch Disk 5 LE51719 $129.99 Ring

2 LE51853 $189.99 Clutch Plate 6 LAE36866 $286.12 Hub

3 LAE30842 $489.39 Plate 7 LAE47003 $369.99 Cradle4 LAE36865 $239.99 Clutch Plate

5000 Series Clutch Parts

JD® 5000 Main Gear Box

34

1

1213

6

2

5

4710

14

9

8

34

1

1213

6

2

5

4710

14

9

8

#3 LJD9616Bearing Core

$45.99 #4

Used Gear SetCALL

#5 LJD9070Bearing Core

$17.77

#6 LAE73345Shaft

$1000.00#7 LJD8195Bearing Core

$81.99 #8 LJD8952Bearing Core

$36.00

#9 AE35549ShaftCall

#10 JD7446Bearing cup

$29.99

#12 E59648NUT

$31.99#13 LAE29271

Arm$75.99

#14 AE29523Bell Housing

CALL

7

23

717-299-3721

22

717-299-37215000 Series Belts

LAE45931Cutter Head Drive Belt

Fits All 5000 Series$70.00 ea. (requires 3)

LE752175000 series floor mat,

Replace your worn out floor mat with this tough ” thick

rubber mat$262.04

LE752175000 series Replac-

ment ceiling Kit$222.75

AZ46671-21Hay Head Drive

21 Spline$600.00 ea.

LE658634/ Banded Belt for

JD5000 K.P. $100.00

BB81Double Sided V Belts for JD Kernel

Processor. 2 Required 8¼” top Pulley

$37.00 ea.BB77

Double Sided V Belts for JD Kernel Processor 2 Required

7¾” Pulley$35.00 ea.

5000 to 6000 Series Adapter FrameEnables you to hook a 5000 Series harvester to any header made for a

6000 Series

*Includes all parts shown!

Order # LAZ58494-A

$2,500.00

17

9

16

6

1

311

11

15

12

213

7

14

4

11

10

8

5

17

9

16

6

1

311

11

15

12

213

7

14

4

11

10

8

5

6000 Low arch Spout

LS70167250mm (11”)

Low Arch Spout$2,400.00

LS70166200mm (9”)

Low Arch Spout$2,200.00

Part# Price Description Part# Price Description1 6SPOBAS-N $700.00 Spout Base (9’) 7 6SPM-D-L-11 $29.99 Middle Def. Liner (11’’)

1 6SPOBAS-W $745.00 Spout Base (11’) 8 6SP-E-D-L9 $21.99 End Def. Liner (9’’)

2 6SPOMID-N $259.00 Middle Section (9’’) 8 6SP-E-D-L11 $24.99 End Def. Liner (11’’)

2 6SPOMID-W $290.00 Middle Section (11’’) 9 6SPOLIN-N $80.99 Base Liner (9”)

3 6SPOEND-NS $183.00 End Section (9’’) 9 6SPOLIN-W $85.99 Base Liner (11”)

3 6SPOEND-WS $193.00 End Section (11’’) 10 6SPOMIDLIN9 $77.99 Mid Liner (9’’) by 5’11’’ long

4 6SPMDEF-N $75.99 Middle Deflector (9’’) 10 6SPOMIDLIN11 $77.99 Mid Liner (11’’) by 5’11’’ long

4 6SPMDEF-W $84.99 Middle Deflector (11’’) 11 6SPO-COV $17.99 Hand Hole Cover

5 6SPODEF-N $67.99 End Deflector (9’’) 12 LAS24 $29.99 Utility Light

5 6SPODEF-W $79.99 End Deflector (11’’) 13 6SPO-ARM.S $24.98 Deflector Side Arm

6 6SPOELIN-NS $42.99 Liner (9”) Short (32.5”) 14 6SPO-ARM.B $27.99 Deflector Side Arm W/Bend

6 6SPOELIN-WS $39.99 Liner (11”) Short (32.5”) 15 LAS20 $469.99 Motor/Actuator

6 6SPOENDLIN9 $49.99 Liner (9”) Long (47.5”) 16 6SPOROD $34.99 Push Pull Rod

6 6SPOENDLIN11 $51.99 Liner (11”) Long (47.5”) 17 LAXE23320 $294.99 Low Arch Hyd. Cyl. 13½” Pin center

7 6SPM-D-L-9 $24.99 Middle Def. Liner (9’’) 17a LAZ251169 $290.00 Low Arch Hyd. Cyl. 12” Pin center

• Fits 6000 & 7000 Series Harvesters• Your high arch spout cylinder will fit our low arch spout

*Hydraulic cylinder & Electric actuator is not included in kit

2524

717-299-37216000 Spout accessories1

4

2

3

1

4

2

3

The tapered discharge deflector ensures a tighter stream of silage or haylage for greater distance when filling trucks or wagons

*John Deere® only

DESCRIPTION Part # Price2) Middle Flap Deflector 6 & 7000 Series (Narrow) LAZ43832 $66.99 Middle Flap Deflector For 6000 Series (Wide) LAZ54380 $66.99 Middle Flap Deflector Tapered for 6 & 7000 Series LAZ43832T $85.991) End Deflector Flap For 6 & 7000 Series (Wide) LAZ47896 $65.99 End Deflector Flap For 6000 Series (Narrow) LAZ53234 $65.99 End Deflector Flap Tapered for 6 & 7000 Series LAZ47896T $65.993) Middle Liner Flap Deflector 6 & 7000 Series Wide LAZ43832L $65.99 Middle Liner Flap Deflector for 6000 Series Narrow LAZ54380L $65.99 Middle Liner Flap Deflector for 6 & 7000 Series Tapered LAZ43832TL $50.994) End Flap Deflector Liner for 6 & 7000 Series Wide LAZ47896L $65.99 End Flap Deflector Liner for 6000 Series Narrow LAZ53234L $65.99 End Flap Deflector Liner for 6 & 7000 Series Tapered LAZ47896TL $45.99

LZ5663714” Spout Rest

$85.00

LAZ39236Cutter Head, Hydraulic

Reverser MotorFits All 6000 & 7000 Series

$1,800.00

LAZ51019Sharpening Stone Motor

Fits 6000 Series SN 501958 to 504343

$549.99

LZ56637-2929” Spout Rest

$98.00

LAZ52237JD 50 Series

Muffler Elbow Deflects Exhaust From Spout

$99.99

LAZ47624JD 10 Series

Muffler Elbow Deflects Exhaust From Spout

$107.99

9.250

11.250

9.250

11.250

6000 KP Belts1

2

JD 6000 and 7000 Series Belts for Cutterhead and KP

1BB74

KP Belt for JD 6000 thru 7500 3 Belts Required (JD #AZ39677)

$33.00ea.

1 B78KP Belt to fit 6000-6950 series, left side $16.99ea.

2LAZ53559

Main Drive Belt for JD for 50 Series, 6 groove 1000 RPM 2 Belts required

(JD#AZ53559) 3/C247

$975.00 set

2

LAZ51312Main Drive Belt for JD 6810 thru 6910,

6 grooves 1000 RPM 2 Belts Required

(Replaces J.D. #AZ51309) 3/C232

$875.00 set

2ALAZ516398

Main Drive Belt for JD for 50 Series, 6 groove 1150 RPM 2 Belts required

(JD#AZ51638) 3/C251

$1100.00Set 7 grove

2A

LAZ51309Main Drive Belt for JD 6810 thru 6910,

6 grooves 1150 RPM 2 Belts Required

(Replaces J.D. #AZ51309) 3/C236

Call

2

7

3

1

5

6

4

2

7

3

1

5

6

4

Part # DESCRIPTION

1 AZ39985 Call Idler Arm

2 Z11967 $12.25 2 Grove Pulley

3 Z49898 Call 50mm Bushing

4 PULID9.X2 $19.44 KP Idler Pulley

5 Z63153 $70.40 45mm Bushing

6 Z13241 Call Pulley

7 B78 $16.99ea. KP Drive belt 2 required

12” pulley size = #2 belt13.5” pulley size = #2A belt

6000 Series KP Drive

2726

717-299-3721

5

12

5

876

5

12

5

876

6000 Series Kernel ProcesserOrder # LS70186

*Adjuster Motor & Brackets not included

13

28

14

30

23

4

3111

26

15

29

27

9

8

25

18

M6 x 50 roll pin

16

20

M10 x 50 Roll Pin

17

7

24

3

19

10

B

12

2221

2

5

1

6

A

13

28

14

30

23

4

3111

26

15

29

27

9

8

25

18

M6 x 50 roll pin

16

20

M10 x 50 Roll Pin

17

7

24

3

19

10

B

12

2221

2

5

1

6

A

LAZ50846

Chain HoistFor 6000 Series JP

$310.00

#A LZ12739Right Hand, Cast

K.P. Deflector$54.50

#B LZ12738Left Hand, CastK.P. Deflector

$54.50

43

$8,500.00

SP194Bearing Hub

$45.50

6000 Series Kernel Processer

1 LAZ54512 $1043.73 • Saw Tooth Roll, Top W/ replaceable Shaft2 LAZ54513 $1043.73 • Saw Tooth Roll, Bottom W/ replaceable Shaft3 LAZ53435 Call • Left, Side Wall4 LAZ53436 Call • Right, Side Wall5 LAZ51890 $85.99 • Top Shield6 LAZ50686 $179.99 • Front Cover7 LAZ39973 $39.99 • Top Angle8 LZ49938 $24.99 • Top Scraper Bar9 LZ62347 $35.99 • Bottom Deflector10 LAZ39644 $104.99 • Bottom Guard11 LAZ51043 $104.99 • Right Bracket12 LAZ51044 $92.99 • Left Bracket13 AZ64877 $280.00 • Idler Lever14 LZ74697 $43.99 • Strap15 LHM182 $49.99 • Extension Spring w/ nut insert16 Z49302 $24.99 • Rod Holder Block17 AZ56297 $177.99 • Top Bearing18 LZ66751 $79.99 • Guide Block, left side rear (when facing unit) 18a LZ81638 $79.99 • Guide Block, left side (when facing unit) *Wide Grove19 LZ66766 $79.99 • Guide Block, right side rear (when facing unit)19a LZ81639 $79.99 • Guide Block, right side (when facing unit) *Wide Grove20 AZ56298 $141.99 • Bottom Roll Bearing21 LAZ50472 $54.99 • K.P. Wear Plate22 LZ63831 $25.99 • Front Guide Right23 LAZ50473 $54.99 • K.P. Wear Plate24 LZ63830 $18.00 • Front Guide Left25 AZ51707 $43.71 • Sleeve / Nut26 LZ65314 $59.99 • Rod27 LZ49978 $17.99 • Holder28 SE17340 $9.99 • Seal 1.75 x 2.4429 AE42998 $56.99 • Core & Bearing30 LZ11975 $179.99 • 3 grove Pulley31 SP189 $4.99 • Cap

Part # DESCRIPTION1 LAZ50444 $181.99 • Roller Brackets W/rollers, Right Hand

2 LAZ50445 $181.99 • Roller Brackets W/rollers, Left Hand

3 LAZ50446-K $222.99 • 10 Series Left Hand Channel Kit

3a LAZ51797-K $171.99 • 50 Series Left Hand Channel Kit

4 LAZ50447-K $222.99 • 10 Series Right Hand Channel Kit

4a LAZ51798-K $170.00 • 50 Series Right Hand Channel Kit

5 LZ64366 $24.99 • 10 & 50 Series Angle

6 LZ63827 $23.99 • 10 & 50 Series Pin

7 Roll Pin $.15 • 1.1/2” X 3/16” Roll Pin

8 124424 $3.99 • 10 & 50 Series Spring

2928

717-299-3721

2

3

9

1

1216

15

13

14

10

11

6

4

5

18

7

17

8

2

3

9

1

1216

15

13

14

10

11

6

4

5

18

7

17

8

Part # DESCRIPTION1 LAZ54524 $3349.99 • Cutter Head, w/ replaceable shaft but no Knives & Hardware2 LAZ48939 $454.99 • RH Spherical Bearing3 LZ12816 $838.61 • RH Bearing Housing4 LJD9307 $160.99 • Bearing Asem. Only5 LAZ71139 Call • 28 tooth Sprocket (We have replaceable weld-on sprocket)6 LAE38694 $375.99 • Housing & Bearing w/ Lock Collar7 AZ53747 $65.00 • Sharpening Stone; SN 504991 & Before8 AZ56626 $64.90 • Sharpening Stone; SN 504992 & After9 LE49449 $49.00 • Shear bar Wear Strip Kit

10 LAZ53906 $469.99 • Corn Shear bar 36mm Thick ~To fit 6650, 6750, 6850 • & 6950 harvester SN. 504342 & after

10a LAZ53906HP $605.00 • High Performance Shear bar (SN. 504342 & after)10b AZ53905 $405.00 • Grass Shearbar 36mm Thick (SN. 504342 & after)

11 AZ47614 $384.99 • Corn Shear bar• To fit 6000 series with SN. 504341 and below

11a LAZ47614HP $540.00 • Hi-Performance Shear bar (SN. 504341 and below)11b AZ47613 $381.25 • Grass Shear bar (SN. 504341 and below)12 LZ69650 $1.79 ea. • Knife Bolt13 LZ71196 $7.89 ea. • Bottom Nut14 Z63136 $17.99 ea. • Corn Knives15 LZ60535 $8.99 ea. • Top Strap16 LZ49622 $16.99 ea. • Grass Knives17 Z62076 $31.99 ea. • Power Saver Knife L.H.18 Z62075 $31.99 ea. • Power Saver Knife R.H.

Grass Knife

Corn Knife

6000 Series Cutter Head

Part # DESCRIPTION

1 LAZ50611SP Call • Upper Front Feed Roll

2 LAZ50611SPT $51.50 ea. • Bolt on tooth, 8 required

3 LAZ50611SPFT $42.00 ea. • Flat Replaceable Crossbar, 8 required• Eliminates wrapping in haylage

4 Z81671 300.12 • Upper Front Feed Roll Shaft

5 LAZ48677 $569.99 • Upper Rear Feed Roll, Stainless Steel

6 LZ60516 $57.99 • Upper Rear Feed Roll Shaft (37” x 32mm hex shaft)

7 LE64796 $59.50 • Feed Roll Lift Arm Spring

8 AZ100686 $77.50 • Feed Roll Wear Plate RH

9 Z65167 $61.50 • Feed Roll Wear Plate RH (SN. 504341 & before)

10 AZ100685 $77.50 • Feed Roll Wear Plate LH

11 Z65168 $61.50 • Feed Roll Wear Plate LH (SN. 504341 & before)

12 LAZ58444 $459.99 • Lower Rear Smooth Roll

13 Z13019 $199.99 • Smooth Roll Cleaner (SN. 504341 & before)

13a Z13356 $206.25 • Smooth Roll Cleaner

14 LAZ50090 $1129.99 • Feed roll, lower front

15 AZ51114 $93.50 • Inside Smooth Roll Drive Coupler

16 AZ51115 $97.50 • Outside Smooth Roll Drive Coupler

17 Call $35.00 • 14 Link Chain

6000 Series Feed Rolls

6

8 9

2

7 13

45

14 12

1

15

3

17 16

11

10

6

8 9

2

7 13

45

14 12

1

15

3

17 16

11

10

Aggressive Feed Roll design helps prevent feeding problems

Power Saver KnifeSave Power

Improved Cut

3130

717-299-3721

8

1

9

6

5

7

2

4

3

8

1

9

6

5

7

2

4

3

Part # DESCRIPTION1 LAZ52676 $80.99 • Cutterhead Shield

2 LAZ39714 $65.99 • Cutterhead Door (SN.504991 & before)

3 LAZ45119 $62.99 • Cutterhead Door (SN.504991 & before)

4 LAZ47099 $76.00 • Cutterhead Cover

5 LAZ54310 $48.72 • Cutterhead Door (SN.504992 & after)

6 LZ63827 $23.99 • 10 & 50 Series Pin

7 124424 $3.99 • 10 & 50 Series Spring

8 LAZ51112 $180.00 • Spiral Floor Plate

9 LAZ54323 $78.10 • Cutterhead Door (SN.504992 & after)

6000 Series Shields

2

1

34

2

1

34

#2 LZ66289Stainless Steel Liner

$81.99

#3 LAZ50457Hay Tunnel Top Pc.

Rubber & Steel strip included$101.99

#4 LZ61182Hay Tunnel Top Pc.

$101.99

#1 LAZ52395Bottom, Hay chute

50 Series$99.99

#1 LAZ52500Bottom, Hay chute

10 Series$101.99

6000 Series Transition

3

4

5

9

1011

12

14

15

1617

13

6

8 7

Part # DESCRIPTION1 LAZ47885 $62.99 • Guide, Rear Feed Channel2 LAZ47085 $37.99 • Feed Guide Top Flap3 LAZ50114 $59.99 • Front Blower Housing Shield4 LAZ46608 $69.50 • Blower Housing Door5 LAZ43828 $46.00 • Top Blower Housing Shield6 LZ62372 $23.29 • RH Blower Band Support Strap7 LZ62966 $22.39 • LH Blower Band Support Strap

8 LZ58148 $65.72 • To fit all early 6000 series harvesters without quick change blower update

8a LZ64776 $78.65 • To fit all 6000 series harvesters with quick change blower or blower update

9 LZ55782 $29.99 • Blower Housing Cutoff Strap (6000 & 7200-7500)

10 Call $44.00 • Blower Paddle Bolt Kit11 LZ72898 $13.69 • Blower Paddle12 LE73207 $215.00 • Spout Worm Gear13 LZ64131 $207.99 • Spout Ring Gear for 200mm spouts13a LZ67194 $207.99 • Spout Ring Gear for 250mm spouts14 LZ58116 $19.04 • Guide 4 Holes, for 200 mm Spout14a LZ72114 $9.75 • Guide 3 Holes15 LAZ56941 $594.00 • Spout Transition (50 Series) 200 mm Spout15a LZ55314 $799.99 • Spout Transition (50 Series) 250 mm Spout16 LZ60500 $24.00 • Spout Transition side wall17 LAZ43830 $22.50 • Spout Transition Inspection Door

3332

717-299-3721

21 21

Misc. 6000 Series PartsLAZ49833

Cutter Head Shield$250.00

LDC42009Cutter Head ShieldTo use w/ hay head

$574.00

LAZ47087 Feedroll Clutch

Plate$69.99

LE73884Hyd. Adapter

$126.99

LAZ58494Replacement Frame for

6K Harvesters

LAZ39902Main Drive Belt Shield

For 10 Series$159.99

LAZ50684Harvester Side Panel

$139.99

LAZ50680Main Drive Belt Shield

For 50 Series$190.00

$1,600.00

made out of spring steel

Made out of ¼” Steel

1 124424 Spring $3.992 LZ44851 Pin $32.25

LDC52047 645 Drive Shaft w/ clutch $475.00LDC35875 640 Drive Shaft w/ clutch $550.00

LDC35876 Drive Shaft 21 spline $321.99

LDC44953 Drive Shaft 23 spline $300.00

Harvester End

Hay Head Drive Shaft

LAZ50434Bottom Clean Out

Door for KP$114.99

LAZ50435KP Deflector

129.99

This adapter is required to upgrade a 6000 series harvester to 4WD

Misc. 6000 Series Parts

AZ48683Electric coil for 6000

Series bottom feed roll $1,775.00

AZ48683Electric coil for 5000

Series bottom feed roll $1,075.00

RE15644Metal detector box for

5000 series$1000.00

RE63617Metal detector box for

6000 series$1,200.00

AZ56805Hyd. Clutch for 6000

series Harvester$3,500.00

RE33127Relay box for 5000 &

6000 series Harvesters$690.00

LZ48790-SPAutomatic Hitch for 6 &

7K HarvestersSpecial Order,

$950.00

LZ48790Hitch Plate, 1” Thick

$153.99

LZ48790-EXHitch Plate, 1” Thick

$174.99

Cleanfix® Reversible fans for radiator cleaning

• save fuel

• provides more usable power

• boost productivity

Check out the Cleanfix® website at: www.cleanfix.org/home

Having problems with a hot engine?

Call for price on used units

106203-KIT Clenfix Fan Kit for J.D. 5830 Harvester $2,520.00100429-KIT Clenfix Fan Kit for J.D. 5730 Harvester $2,520.00100557-KIT Clenfix Fan Kit for J.D. 6950 Harvester $3,250.00

Call for pricing on other harvesters or tractors

34 35

717-299-3721

5

17

22

15 14

16

21

23

18

13

12

10

19

20

10mm Nut

11

3

8

49

7

6

M10 x 30Bolt

5

17

22

15 14

16

21

23

18

13

12

10

19

20

10mm Nut

11

3

8

49

7

6

630A-B + 640A-B Parts

LDC27497 Hay Head Frame

$850.00

Check out the Polly Pickup Band!!

LDC205047 Auger

$2000.00

30mm Chrome arm for 630AAllows you to use #9

(LDC49073) on a 630A(will make your head last

longer)

# LDC27512N

3

1

2

9

6

4

8

5

7

3

1

2

9

6

4

8

5

7

640A-B Parts

Item Part# Description Price3 LDC33024 Skid Shoe, fits 630 or 640 $97.16

4 LCC44956 Left Hand Cam $110.99

5 CC44955 Right Hand Cam $149.99

6 LDC27512 Arm for 630A (or 7½ Ft) $41.00

7 LDC49040 Arm for 630B L.H. $45.00

8 E69259 Spider For 630A (or 7½ Ft) $187.99

9 LDC49073 Spider For 630A & B + 640A & B $239.99

10 CC48770 Bushing $22.99 ea.

11 E54745 Pickup teeth $4.99

12 LCA100183 Angle for 630B $139.99

12a LCC27506 Angle for 630A $140.99

13 E85043P Poly pick up band features a flexible high impact poly, which improves the life of the pickup teeth and dose not become deformed by rocks $29.99 ea

14 CC44873 Cylinder Rod Guide (Ball Holder) $5.99

15 Z11366 Auger Tooth $13.99

16 CC44872 Cylinder Rod Guide (Ball Holder) $5.89

17 Z32146 Finger Ball $12.99

18 LH36018 Hand Hole cover $22.99

19 LDC46805 Top Shield $27.99

20 LCC43488 Bottom Left shield $58.00

21 LE57986 Wear Strip L.H. $63.9922 LE57985 Wear Strip R.H. $63.9923 CC52031 ¼” C Channel $135.74

Item Part# Description Price1 LDC205017 Auger $2,200.00

2 LCC49490 Replacement Floor $215.00

3 CC44955 RH Cam $149.99

4 LCC44956 LH Cam $110.99

5 LDC49073 Spider $239.99

6 CC48770 Bushing $22.99

7 LDC27512 Arm $42.99

8 LDC204004 U Channel LH $144.99

9 LDC204003 U Channel RH $144.99

36 37

717-299-3721

2128

17

20

14

26

23

18

16

19

11

22

8

7

24

2725

15

2

1029

22

12

9136

5

1

4

3

2128

17

20

14

26

23

18

16

19

11

22

8

7

24

2725

15

2

1029

22

12

9136

5

1

4

3

Item Part# Description Price1 LXQ9965580 Left Wing Crop Divider for 666 Corn Head $359.99

LXQ9965590 Right Wing Crop Divider for 666 Corn Head $359.99 1a LXQ9128410 Left Crop Divider for 664 Corn Head $351.02

LXQ9128400 Right Crop Divider for 664 Corn Head $351.022 XQ9099451 Flanged Bushing $14.993 LXQ9109913 Left Hand Crop Divider Nose $166.993a LXQ9109933 Right Hand Crop Divider Nose $166.994 LXQ9111501 L H Driver Deflector $34.994a LXQ9111511 R H Driver Deflector $34.995 XQ9118260 24.3/8” Plastic Wear Strip $16.986 LXQ9120220 24.3/8” Wear Strip Bracket $35.007 LXQ9120090 18.1/8” Wear Strip Bracket $39.398 XQ9099580 18.1/8” Plastic Wear Strip $13.569 XQ9118250 20.1/2” Plastic Wear Strip $15.99

10 LXQ9120080 20.1/2” Wear Strip Bracket $36.9911 LXQ9120822 Cleaner $4.9912 LXQ9120872 Cleaner $17.9913 LXQ9121990 Sprocket w/ 30mm bore + keyway $85.99

John Deere® 666 & 664 Corn HeadItem Part# Description Price

14 LXQ9096112 Crop Divider, Shoe $162.9915 LXQ9120035 Shaft $98.99 16 XQ9120860 Bushing $5.9917 Chain (See Chain breakdown)18 XQ9120541 Top Side Chain Guide $30.9919 XQ9131970 Top Gathering chain $119.9920 LXQ9131320 Weld on Wear strip for 666 $16.9921 LXQ9131510 Weld on Wear strip for 666 $6.0022 LXQ9131271 Weld on Wear strip for 666 and 664 $16.5223 LXQ9929410 Center Weld on Wear strip for 666 and 664 $14.9924 LXQ9121850 Sprocket w/ Splined Bore $93.5025 LXQ9125510 Splined hub $30.8726 LXQ9131851 Right Hand Wear Sheet $85.9926a LXQ9131891 Left Hand Wear Sheet $85.9927 LXQ9927410 Bottom Shield for 666 $69.9927a LXQ9123280 Bottom Shield for 664 $107.9928 LXQ9118352 Shaft $45.7629 XQ9116641 Cutter Disc Knife $148.23

Part# Description Price

1 AZ51762 48 Link Gathering Chain $99.99

2 AZ51763 50 Link Gathering Chain $114.99

3 AZ51764 52 Link Gathering Chain $124.99

4 AZ51765 54 Link Gathering Chain $132.99

4 Row Breakdown

6 Row Breakdown

John Deere® 666 & 664 Chains

38 39

717-299-3721

5

10

6

7

19

17

8

22

18

7

20

23

15

13

24

16

11

21

12

5

9

10 10

14

1

4

3

2

5

10

6

7

19

17

8

22

18

7

20

23

15

13

24

16

11

21

12

5

9

10 10

14

1

4

3

2

Item Part# Description Price1 LAE45603 L.H. Top Rear Wear Plate $111.991a LAE45604 R.H. Top Wear Plate $111.992 LE67061 Liner 18.5” Wear Plate Guide $22.993 LE67062 Liner 32” $31.994 LE74247 Bottom Wear Plate (Short) $21.995 LE74297 Wear Shoe $27.996 LAE45535 L.H. Cover Wear Plate $151.996a LAE45534 R.H. Cover Wear Plate $158.997 LE68294 Liner (43”) $39.998 LE74211 Bottom Wear Plate (Long) $30.009 LAE45198 R.H. Cover Plate (serial # before 651001) $198.999a LAE45199 L.H. Cover Plate (serial # before 651001) $198.9910 AE49269 Ball Joint $24.9911 LAE41722 Pittman Arm $101.9912 LAE38172 Pittman Connector Arm $77.99 13 LE63662 Gear Box Shaft (Heat treated) $149.9914 AE46075 13 Tooth Hardened Sprocket $59.99

JD® 4 Row (conversion Head)

Item Part Description Qty. Price1A LAE44155 (108 Links-27 Lugs) 2 $295.00

1B LAE44156 For Serial # 651001- (112 Links-28 Lugs) 2 $305.00

1C LAE44151 For Serial # 651001- (64 Links-16 Lugs) 2 $165.00

1D LAE44152 For Serial # 651001- (88 Links-22 Lugs) 2 $249.00

JD® 4 Row (conversion Head)Item Part# Description Price

15 JD10240 Needle Bearing $19.9916 AH98118 Seal (before serial # 630000) I.D. 1.75 - O.D. 2.375 $6.1017 AE43551 Seal (after serial # 630000) I.D. 1.75 - O.D. 2.72 $9.9918 JD8855 Needle Bearing $14.0019 JD8674 Ball Bearing $23.9920 C3059E Snap Ring $4.9921 Z9950H Snap Ring $6.9922 LE63662 Gear Box Shaft (Heat treated) $149.9923 E74282 Knife Support RH $279.9923 E74283 Knife Support LH $209.9924 E74284 Knife Support Outdide $175.99

Chain with rollers on pins!

41

717-299-3721

40

717-299-3721

LAE29398Spinner For JD® 3 row

$148.99

JD® 3 Row (conversion Head)

#4 AE270792row Chain

$129.99

#1 AE3334026 lug Chain

$199.99

#2 AE3334124 lug Chain

$179.99

#3 AE3334220 lug Chain

$169.99

JD® 2 Row (conversion Head)

5

2

3

4

1

6

7

5

2

3

4

1

6

7

L86549263N.H. 824 to FP 230

Adapter Kit$680.00

New Holland® 824 Corn Head

Part# Description Price1 L644107 Sprocket $82.992 644463 Shaft 10-1/8” Long Call2a 856144 Shaft 9-1/4” Long Call2b 856145 Shaft 9” Long Call

3 L646514 replacement plate to weld upper crop guide ontoSpecify Left or Right Hand $7.99

4 L646524 L.H. wear strip $39.994a L646525 R.H. wear strip $39.995 L646523 Wear Strip 27¼” long $41.996 L646360 Wear Strip 8¾” long $23.99

7 L645365 This is a weld on plate for front nose pc.Use to replace original one if it gets mangled $25.99

Part# Description Price

1 640148 Chain (58 link) $125.99

2 644591 Chain (64 link) $145.99

3 685133 Bottom Chain(48 Link) $106.99

42 43

717-299-3721

2

1

2

1

New Holland® FX, Parts

L9620356Smooth Feed Roll

CALL

L7943581900 and 1915 Blower Band

$275.00L574597

1900 and 1915 Blower Band Liner

$74.99

$2,500.00

Misc. Hay Head Teeth

Kit to adapt a 990W to FP Drive

L84334020KP Bottom Deflector for Corn

Fits New Holland FX Series$220.00

Idass Grass Head Teeth#1 GEHAYTEE $10.99

3-3/8” OPENING SQ. BACK 9#2 GEHAYTEE306-360 $10.99

3-1/4” OPENING SQ BACK 6#3 GHHAYTEE $10.99

2-3/4” OPENING U BACK 9

1

2

3

PICTEEMAIMaize Grass Head Teeth

$5.25 ea.

E54745JD® Grass Head

Teeth 7-1/2’’Call

#2 L8662032627P Brace$14.99

#3 L8662766727P drive Shaft

Call

E74678JD® Grass Head

Teeth 7-1/2’’$2.92

#1 L8662528127P drive bracket

$41.99

For NH 350 and 355NH® Rubber Teeth

Call

order #L84017677

FX Series, Adjustable SpoutFits All FX Series Harvesters

8

5

7

2

654

31

8

5

7

2

654

31

4 46810 Snap Ring $3.195 BB-62072RS Bearing $24.576 46809 Snap Ring $12.99 7 L86627514 Bearing Holder $98.99 8 86625291 Spline Shaft $98.60

990DRKKIT$539.00

New Holland® FX, Parts

L84043069Regular Rear Hitch Fits All

New Holland® FX Series $250.00

L84043069-AAutomatic Rear Hitch

Fits All New Holland® FX Series(Special Order Only)

Call For Pricing

1

2

31

2

3

1L84017260L Ware Plates

$38.00 ea.

2L84004619 Blower Arm

$70.00 ea.

3L84004820 Blower Paddle Cupped

$26.28 ea.

2

3

1

2

2

3

1

2

FX Series Grass Crop Deflector1 L84005239 — Deflector Plate $180.002 L84068493 — Deflector Plate $76.313 L8417507 — Mounting Guides $81.84

L84045350Blower Cut off Plate

Fits FX Series$40.50

L86505871Blower Paddle

Fits NH® 1915; (3 Required)$37.00

L86624827Hay Head Arm

NH® 824 Hay Head$50.36

L840684930Bottom Cutter Head Plate

Fits New Holland® FX Series$220.00

L601081

NH® 1900 Shoot/Door(special Order)

$211.35

L708652NH® 2100 Shoot/Door

(special Order)$131.98

44 45

717-299-3721

10

7

11

91 2

3 4

8

5 6 4

10

7

11

91 2

3 4

8

5 6 4

NH® 360N Gathering Chains

3 Row Narrow

6 Row Narrow

7 L86502834Corn Head Chain, 92 Pitch $309.99

8 L86502835Corn Head Chain, 96 Pitch $324.99

9 L86593263Corn Head Chain, 88 Pitch $259.99

Part# Description Price360ND-kit Adapter Kit, 360N-FP (All Parts Shown) $579.66

1 L86554060 Support $21.982 L86633811 Bracket $87.623 46810 Snap Ring $3.074 BB-62072RS Bearing $24.575 L86627514 Bearing Holder $98.996 46809 Snap ring $3.157 L86570486 Spline Shaft - Sprocket $128.388 #60 Chain9 L86631936 23 tooth Splined Sprocket $102.00

10 L86633816 Drive Shaft $126.0011 FB-1375 Flange Bearing $60.00

4 Row Narrow 13

4

10

12

11

76

8

18

5

17

9

15

16 14

20

15

19

3

1

2

13

4

10

12

11

76

8

18

5

17

9

15

16 14

20

15

19

3

1

2

NH® 360N Parts & Adapters

Part# Description Price1 L86624588 Side Spinner Corn Head Fits all 360N Headers $76.99 2 L86624587 Spinner Teeth (takes 4) $13.99 3 L86631932 Sprocket W/ extension $115.994 L9802155 R.H. Wear Plate $24.995 L9802154 L.H. Wear Plate $24.996 L9802093 Center Wear Plate for NH® 360N4 & 360N6 $24.997 L86622496 Teeth for Auger Feed $26.258 L86633820 Wear Strip for 360N $31.99 9 L9809311 Wear Strip for 360N3 center row $30.99

10 L9620056 Cleaner $12.0011 L86542662 Bearing Housing w/ hex bearing $277.9912 L86619955 Floor for FP240, fits 360N / 3PN $75.9914 L86631939 14 Tooth Drive Sprocket Drive $92.9915 9800740 Bearing $45.99 16 L86633833 Bearing Housing $165.9917 9822696 Spline Shaft (for cutter Disc ) $354.9918 9843538 Cutter Disc $195.8919 L86631931 13 Tooth Idler sprocket $74.99 20 L86631930 14 Tooth Idler sprocket $89.99

#13 CHR500Adapter kit to go from NH® 360N 3 row to JD® 3000 or

5000 Harvester$850.00

CHR540Adapter kit to go from NH®

360N 4 or 6 row to JD® 5000 Harvester

$1200.00

We also have a kit that will allow you to connect a 360N 6 row to a

JD® 6000 Harvester(Special order only)Call for pricing

46 47

717-299-3721

63

21

45

63

21

45

Part# Description Price1 L289946 Rotor $270.002 L578343 Arms $19.33

3 L578342 ¼” AR Steel-Paddle $11.37

4 L86629511 Washer $6.905 L221481 Bolt $13.606 L578277 Spinner Hopper Call

Part# Description Price1 L791715 Blower Center $340.002 BEAPB1.75 1¾ Bearing $60.003 L58639 Shim $5.504 L791715 Paddle $35.005 L791719 Arms $85.006 LHM1008 Shaft (Replaceable) $456.00

Part# Description Price1 L791716N 3 Paddle Center $217.99 2 L791715N Cup Paddle $51.993 L791719N Paddle Arm $41.994 BLO40104A Bottom Strap $5.665 5/8” Carriage Bolt $.756 5/8” Lock Nut $.357 3/4” Machine $.758 3/4” Lock Nut $.50

NH® 40 Blower Parts

3

2 1

4

5 6

3

2 1

4

5 6

8

1

7

5

6

3

4

28

1

7

5

6

3

4

2

L791710A 40 Blower Center Replacement Kit

Comes Assembled & Balanced $610.53

2

10

9

4

11

8

5

12

6

1

7

3

2

10

9

4

11

8

5

12

6

1

7

3

NH® 40 Blower Parts

Item Part# Description Price1 L851536 Rear Panel $192.022 L851532 Front Panel $156.333 L795413 Cover $5.504 L791922 Liner $85.005 L791923 Blower Band $292.006 L851539 Blower Discharge $497.007 L570709 Clean-out Door $65.008 L690309 Tie Bars $25.009 L851541 Eye Bolt 5 1/4” long $21.31

10 L697866 Eye Bolt 8" Long $18.2711 L601416 Hook Bolts $5.5012 L263818 Shim $3.50

Blower Discharge 30 Blower Bandorder #

LS70168

$692.00

$256.00

49

717-299-3721

48

1

324 5

1

324 5

Part# Description Price1 L86636978 Front Panel $134.99

2 L86615412 Cupped Paddles $37.99 ea.

3 L225396 BandReplaces N.H. # 86636614 $178.99

4 L225387 Liner $65.99

5 L86637313 Rear Panel FP230 &FP240 $147.99

5a L9614491 Rear Panel 900 A.S.# 781115 $210.00

5b L678912 Rear Panel 900 B.S.# 781115 $210.00

Misc. Cup PaddlesL289984

Cupped Paddles for N.H. 30

$45.99 ea.

L9610638Cupped Paddles for

N.H. 900$41.99 ea.

L182740Cupped Paddles for

N.H. 28$41.99 ea.L238321

Cupped Paddles for890 & 892$39.99 ea.

LAE37844

Cupped Paddles for J.D. 3000 Series

$35.99 ea.

L9604054Cupped Paddles for

790, 782$40.99 ea.

DIONPADDLEBlower Paddles for

Dion$43.99 ea.

DIONPADDLECUPCupped Paddles for

Dion$54.99 ea.

NHTM FP230 & FP240 Parts

Part# Description Price

676997 Knife, fits: NH® 900 &NH® FP230 $75.99

86624446 Knife, fits: NH® FP230 $74.99

9617519 Shear Bar for NH® 900SN. 751186 & - $136.99

9611168 Shear Bar for NH® 900 SN. 751186 &+ $169.99

86632788 Shear Bar for NH® FP230 $227.9986632157 Shear Bar for NH® FP240 $248.99

This also works on 900 Harvester

1

24

3

1

24

3

Part# Description Price

1 L143727C1Blower Transition Chute

for Case IH IH, Miller Pro, & Badger, 600 Blowers

$321.99

2 L148113C1Blower Band for Case IH IH, Miller Pro, & Badger

600 Blowers$366.99

3 143746C1 Angle Arm $51.00

4 LSC301Cupped Blower Paddle

Fits Case IH IH, Miller Pro, & Badger

$46.99

Blower Bands

We Also Have Blower Bands for N.H. 23 & 24 -N.H 40, Dion,

Badger, and many others. If you need a Blower Band, and you don’t see it here, Give us a call, we may have it, or we may be able to

make it!717-299-3721

12

3 12

3

Sliding Shoe Kit NH 340W & 350W

#1 Main Shoe L86512471 $144.99

#2 Shoe Pad L9843189 $44.99

#3 Angle Bracket L9828568 $39.99 Replaces # 9843189 or 89820248 or 89843189

L781159N.H. 27 & 28

$354.99

NH® 900Cutter Head order #

L636324

$1349.99

50 51

717-299-3721

11 10

4

5

9

63

2

1

8

7

11 10

4

5

9

63

2

1

8

7

Item Part# Description Price1 LCA67656 LCA72673 Adapter Frame $1,100.002 LCA74872 684 LH Deflector $36.993 LCA74871 684 RH Deflector $36.994 LCA72673 Corn Head Leg $66.995 LCA64337 Tube will fit JD® 676 or Kempertm 4500 $311.99 6 LCA69426 Gear box 676 or Kempertm 4500 $1975.957 LCA65088 Strap $7.998 19M8954 M10 X 60 $2.459 LCA04087 Spring $.80

10 14M7274 Bevel nut $5.9911 LCA53566 Eye Nut $4.99

LCA76651688 to 6K series Adapter Frame

$1600.00

676 Adapter Plate

LCA74296-LHLCA74297-RH

Nose Support for 684 & 330 Kemper

$381.99

50

234

1

234

1

Header Drives

2

1

2

1

John Deere® 5000 series toKemperTM header, adapter Kit

for 684, 686, & 330 KemperTM *We also have all parts needed to repair this adapter,

Call for pricing.$5,000.50

Order # LCA77120

#1 LCA91232KemperTM 684

Main Frame / Gearbox$2000.00

#2 LS5072-SWear Plate set

$112.50

LCA84340-LHLCA84341-RHDrum Cleaner

$449.99

LCA75930-LHLCA75931-RH

$219.99

684, 686, 688, 330, Corn Head Drive

LCA72281 21 to 23 spline $999.99LCA69888 21 to 21 spline $999.99

Drive for 676 JD® or 450 Kempertm

LCA73023-21 21 - 21 Spline $525.00LCA73023-23 21 - 23 Spline $525.00

LCA64231 21 - 6 Spline $525.00LCA72150 23 - 6 Spline $525.00

630 Hay Head Drive

AZ46671-21 21 to 21 spline $600.00AZ46671-23 21 to 23 spline $600.00

1 AZ46668 Cross Bearing(fits all drives on this Page) $46.99

2 M86290 Cam $2.993 M86291 Outside Clutch Spring $1.994 M86292 Inside Clutch Spring $1.89

AZ50052 21 spline $204.99AZ50429 23 spline $134.99

52 53

717-299-3721

3 1

4

5 2

3 1

4

5 2

5 61

33 42

5 61

33 42

8

12

3

6 5 7

4

8

12

3

6 5 7

4

Item Part# Description Price1 JD9241 Bearing $59.992 40M7066 Snap ring $7.993 LCA65112 Snap ring $10.294 LCA67316 Drive Coupler $51.995 LCA67317 Drive Coupler $51.996 LCA64574 Compression Spring $15.99

Item Part# Description Price1 LCA66032 Large Drum $784.99

2LCA66037 LLCA66037 R Hardened teeth Blade $31.50ea.

3 LCA64423 Small Drum $215.00

4LCA66035 LHLCA66036 RH Small Drum hardened teeth Blade $32.99 ea.

5LCA67156 LHLCA67157 Rh Cleaner $11.99

#1 LCA64910Outside Skid Plate

$49.99#2 LCA65111 - L.H.

LCA65112 - R.H.Wing Skid Plates

$195.99#3 LCA71880 - L.H. LCA71879 - R.H.

Center Skid Plate$95.99

#4 LCA69519 - L.H. LCA69520 -R.H.

Drum Shield$285.99

#5 LCA67554Replacement Shaft to weld into spinner if the original

one gets bent$62.99

#6 Bottom plate $8.00

#7 Top Plate $8.00#8 LCA67550 - L.H. LCA67551 - R.H.

Wing Crop Driver Snout$124.99

KemperTM 4500 & J.D. 676 Spouts

$2,500.00

$2,100.00

$2,400.00

order #L84017677

order #L577654

order #CL141797

FX Series, Adjustable SpoutFits All FX Series Harvesters

1900 Series, Adjustable SpoutFits All 1900 Series Harvesters*

This spout features a two stage deflector for improved control of forage place-

ment

Low Arch / Waggon Spout for Class® Harvester

*You will need to take the frame off of the old spout, cut it down and bolt it to the new spout.

54 55

717-299-3721KemperTM ChampionTM 3000 Parts

12

3

12

3

2

3

1 2

3

1

Item Part# Description Price1 LCA67184 Spring Plate $27.922 LCA57911 515/16” O.D. Friction Plate $16.993 LCA66024 Main Drive Clutch Assembly Call

Main Drive Clutch

#1 LCA56992 - R.H. LCA56993 - L.H.

Drum RotorFits Champion 3000, 4 row

$$1095.00#2 LCA56726

Weld-in Drum Rotor Repair Panel

$14.99 ea.LCA66037LLCA66037R

Cutting Blade16 required$32.99 ea.

#1 LCA61490 - R.H. LCA61491 - L.H.

Outside Skid Plate$145.99

LCA53162 - R.H.LCA53161 - L.H.

Rock Gard$886.25

#1 LCA489526 point Weld-on Drum

segment 24 required$15.99

#1 LCA494968 point Weld-on Drum

segment 24 required$16.99

#1 DC38275Clutch friction disc

Fits Kempertm 450 6-row Drum clutch

$15.99

#1 LCA57012Idler bracket

$49.99#2 LCA56422

Spacer Strap$15.99

#3 10 tooth Idler Sprocket

$45.36

31

231

2

Needed when connecting Champion 3000 onto a J.D. 5K Harvester

#3

3

5

4

3

5

4

22

LCA57399 RHLCA57400 LH

Outside crop driver$Call

LCA58242Main Gearbox

$6400.00

LS1354Weld on repair plate for

center floor$39.42

LCA5633916 tooth Drive Sprocket

$125.00

#1 LCA57401 RH LCA57402 LH

$850.00

#2 LCA55974Wear Plate

$46.60#3 LCA67554-2

Bottom Plate $8.00

#4 LCA67554-1Top Plate

$8.00#5 L55608

Replacement Shaft$91.30

1

For more info and a complete breakdown of 3000 kemper visit our website at

www.lancasterpartsandequipment.com

*used part pictured, call for availability

*used part pictured, call for availability

*used part pictured, call for availability

KemperTM 4500 & J.D. 684, 686, or 688

LCA77468 = LHLCA77469 = RH

End Plate for corn headRH version pictured

$645.00

5756

Lancaster Bale Grabber

#BG200$2,400.00

Arms are linked together. Links can be removed if

free moving arms are preferred.

Skid Loader Attach.

included in Price

J.D. 700 & 800

Tractor Hookup

extra

J.D. 300 & 400

Tractor Hookup

extra

2’’ Cylinder Rod

21 21

LS8150149” Bale Spear (Heavy duty)

$98.06LS81502

43” Bale Spear (Heavy duty)$83.00

LS8150339” Bale Spear (Heavy duty)

$79.00

LS8150432” Bale Spear (Heavy duty)

$75.00LS81505

39” Bale Spear (Light duty)$50.00

LS8150632” Bale Spear (Light duty)

$47.00

#1 SPEARSLESpear Sleeve

2-1/8” round = 4¾”$11.00

Bale Spears

Do you have a John Deere® 5000 Series Harvester? Well we have the parts you need. At Lancaster Parts and Equipment, we have a large selection of donor machines for the picking. With 20 years of experience, we have the parts and knowledge you need to get the job done.

7000 Series KPCall for price and

availability

LAZ64008 = RHLAZ64007 = LH

7000 K.P. Quick Conversion Guides

$180.00 ea.

7000 series Kernel Processor

Tractors

Harvester Heads

5000 & 6000 Series Harvesters

We offer a large selection of headers. From independ to row pickup, we’ve got what you need for harvest season.

USED EQUIPMENT

Forage BoxesWe not only have forage boxes, but also used wheels and axles.

lancasterpartsandequipment.com

2008 Horseshoe RoadLancaster, PA 17602

(717) 299-3721 NON-PROFITORGANIZATION

U.S. POSTAGE PAIDLEBANON, PA

PERMIT NO. 146

Hours, Monday - Friday 6:30am - 4:30pm