1. 3-7. Other interior featuresSun visorsType A Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. 3Interior and exterior featuresType B Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. Side extender: Place in side position, then slide backwards.373

2. 3-7. Other interior featuresVanity mirrorsVehicles without vanity lightVehicles with vanity lightSlide the cover.The light turns on when thecover is opened.374 3. 3-7. Other interior featuresClockAdjusts the hoursAdjusts the minutes 3Interior and exterior features The clock is displayed whenThe engine switch is in the ACC or ON position. When disconnecting and reconnecting battery terminalsThe time display will automatically be set to 1:00.375 4. 3-7. Other interior featuresOutside temperature display (vehicles with auto anti-glare inside rear view mirror)The temperature display shows temperatures within the ranges of-40F (-40C) and 122F (50C). Outside temperature displayType AType B Ice advisory indicatorIf the outside temperature low-ers to 37F (3C) or belowwhen the engine switch is inthe ON position, the indicatorwill come on to warn the driverthat roads may be icy. Checkthe road surface and drivecarefully. (The indicator will gooff when the outside tempera-ture rises to 41F [5C].)376 5. 3-7. Other interior featuresChanging the displayThe outside temperature display on the inside rear view mirror can beturned on/off and the display units can be changed. Turning the outside temperature display on/off Type A: Press and hold to display Custom Settings Menu. Type B: Press to display Custom Settings Menu.Type A: Press and selectOutside Temperature,then press and hold.3Type B: Press and selectInterior and exterior featuresOutside Temperature,then press .Type A: Pressand selectTemperature Display.Type B: Pressand selectTemperature Display. Type A: Press and hold and select display on/off. Type B: Pressand select display on/off. To leave the Temperature Settings Menu, select Back to main menu to return to the starting screen, then either select Exit or wait several seconds without pressing any buttons. 377 6. 3-7. Other interior features Changing display unitsType A: Press and hold to display Custom SettingsMenu.Type B: Press to display Custom Settings Menu. Type A: Press and select Outside Temperature, then press and hold . Type B: Press and select Outside Temperature, then press . Type A: Press and select Units. Type B: Press and select Units.Type A: Press and hold and select the desired units.Type B: Pressand select the desired units.To leave the Temperature Settings Menu, select Back tomain menu to return to the starting screen, then either selectExit or wait several seconds without pressing any buttons.378 7. 3-7. Other interior featuresSetting the ice advisory indicatorThe ice advisory indicator on the inside rear view mirror can beturned on/off. Type A: Press and hold to display Custom Settings Menu. Type B: Press to display Custom Settings Menu. Type A: Press and select Ice Advisory. Type B: Press and select Ice Advisory. 3Interior and exterior features Type A: Press and hold and select display on/off. Type B: Pressand select display on/off. To leave the Temperature Settings Menu, select Back to main menu to return to the starting screen, then either select Exit or wait several seconds without pressing any buttons. 379 8. 3-7. Other interior features The outside temperature is displayed when The engine switch is in the ON position. Display In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change: When the vehicle is stopped, or moving at low speeds (less than 16 mph [25 km/h]) When the outside temperature has changed suddenly (at the entrance/exit of a garage, tunnel, etc.) When or is displayed The system may be malfunctioning. Take your vehicle to your Toyota dealer. Customization that can be configured for the inside rear view mirrordisplay Settings (e.g. layout) can be changed. (Customizable features P. 583)380 9. 3-7. Other interior featuresPower outlets (12V DC)The power outlets can be used for 12V accessories that run on lessthan 10A.3 The power outlets can be used when Interior and exterior featuresThe engine switch is in the ACC or ON position. NOTICE To avoid damaging the power outletsClose the power outlets lid when not in use.Foreign objects or liquids that enter the power outlets may cause a short cir-cuit. To prevent the fuse from being blownDo not use an accessory that uses more than 12V/10A. To prevent the battery from being dischargedDo not use the power outlets longer than necessary when the engine is notrunning. 381 10. 3-7. Other interior featuresPower outlet (120V AC)The power outlet can be used for electrical appliances.Main switchTo use the power outlet, turn on the main switch.The power supply starts a few seconds after the main switch ispressed.Power outlet socket Maximum available capacity of the power outlet While the vehicle is being drivenThe maximum capacity of the power outlet is always 120V AC/100W. When the vehicle is stationaryThe maximum capacity of the power outlet varies depending onthe following conditions. The maximum capacity is 120V AC/400W when the followingcondition applies: The shift lever is in P or N. (automatic transmission): If equipped382 11. 3-7. Other interior features The shift lever is in N and the clutch pedal is not depressed. (manual transmission) A maximum capacity of 400W can only be restored by turning the power outlet main switch off and then on again under condi- tion described above. The maximum capacity is 120V AC/100W when the followingcondition applies: The shift lever is moved to any positions other than P and N. (automatic transmission) The clutch pedal is depressed. (manual transmission) The power outlet can be used when3 The engine is started.Interior and exterior features The indicator light changes according the maximum available capacity,as follows:Indicates 120V AC/400WIndicates 120V AC/100W When the power outlet is in operation The sound of the cooling fan may be heard from the front console box. This is normal and does not indicate a malfunction. If the engine is started with the power outlet main switch on The maximum capacity of the power supply may decrease to below the stan- dard, or may be cut off completely, even when the vehicle is stationary. 383 12. 3-7. Other interior features The protection circuit may be activated to cut the power supply if anyof the following conditions apply: The engine is started with the power outlet main switch on. Use of electrical appliances exceeding the maximum capacity is attempted.A sound may be heard when the protection circuit is activated.This is normal and does not indicate a malfunction. Electrical appliances, which consume power exceeding 100W, have been used continuously for a long time period. The total power usage by all electrical features (headlights, air condition- ing, etc.) has exceeded the total vehicle maximum for an extended period of time. If the protection circuit is activated and the power supply is cut, con-duct the following procedure:Park the vehicle in a safe place, and then securely apply the park-ing brake.Check and ensure the following conditions: The shift lever is in P or N. (automatic transmission) The shift lever is in N and the clutch pedal is not depressed.(manual transmission)Make sure that the power consumption of the electric appliance iswithin the maximum capacity of the power outlet and the applianceis not broken.Press the power outlet main switch again. When the cabin temperature is high, open the windows to cool the tempera- ture down. Once it reaches the normal temperature, turn the power outlet main switch on again. If the power supply is not resumed even after performing the above proce- dure, have the vehicle inspected by a Toyota dealer.384 13. 3-7. Other interior features CAUTION Using a power outlet Observe the following precautions to reduce the risk of injury. Use of the power outlet when it is wet with rain, drinking water or snow may result in electrical shocks and is extremely dangerous. The power outlet must be thoroughly dried before use. Do not allow children to use or play with the power outlet. Be careful not to get any part of your body caught in the power outlet lid. When using electrical appliances, strictly follow any cautions and notices written on their labels and in the manufacturers instruction manuals. Do not modify, disassemble or repair the power outlet or its inverter, in any3 way. Doing so may result in unexpected malfunctions or accidents, which could cause serious damage or injuries. Contact a Toyota dealer for any necessary repairs. Interior and exterior features To prevent injuries and accidents, securely fix all electric appliancesbefore use and do not use any appliances that may do any of the fol-lowing: Distract the driver while driving, or hamper safe driving. Result in a fire or burn injuries due to the appliance rolling, falling or over- heating while driving. Emit steam, while the windows of the cabin are closed. To prevent unexpected accidents, such as electric shocks, do not per-form any of the following Using the power outlet for electric heaters while sleeping. Contaminating the power outlet with liquid substances or mud. Handling electrical appliance plugs at the power outlet with wet hands or feet. Inserting foreign objects into the power outlet. Using malfunctioning electric appliances. Inserting inappropriate or badly fitting plugs into the power outlet.385 14. 3-7. Other interior featuresNOTICE To avoid damaging the power outlet and the plug Close the power outlet lid when not in use. Foreign objects or liquids that enter the power outlet may cause a short circuit. Do not use plug adaptors to connect too many plugs to the power outlet. After inserting a plug, gently close the power outlet lid. To prevent the fuse from being blown Do not use a 120V AC appliance that requires more than maximum capacity. If a 120V AC appliance that consumes more than maximum capacity is used, the protection circuit will cut the power supply. Appliances that may not operate properly (120V AC) The following 120V AC appliances may not operate even if their power con- sumption is under maximum capacity. Appliances with high initial peak wattage Measuring devices that process precise data Other appliances that require an extremely stable power supply To prevent the battery from being discharged Turn off all the vehicles electronic equipment and accessories, such as the headlights and air conditioning, when electrical appliances that consume in excess of 100W are used continuously for long periods of time. To prevent any damage caused by heat Do not use any electrical appliances that give off intense heat such as toasters, in any locations including the internal or external trim, seats and deck. Do not use any electrical appliances, which are easily affected by vibration or heat, inside the vehicle. Vibration while driving, or the heat of the sun while parking, may result in damage to those electrical appliances.386 15. 3-7. Other interior features NOTICE If any electrical appliances are to be used while drivingSecurely fasten both the appliances and their cables to prevent them fromfalling or getting caught any of the power train components. If the power outlet is loose when an electrical appliance plug is con-nectedReplace the outlet.Contact a Toyota dealer for any necessary replacements. If the power outlet gets dirtyTurn the main switch off and use a soft, clean cloth to wipe it gently.Do not use any cleansing materials, such as organic solvents, wax, or com-pound cleaners, as these may damage the power outlet or cause it to mal-3function. Interior and exterior features387 16. 3-7. Other interior featuresSeatback tableFront passengers seatback can be used as a temporary table onlywhen the vehicle is stopped.Fold down the front passen-gers seat to use the seatbacktable. (P. 51)CAUTION Caution while drivingObserve the following precautions to avoid death or serious injury. Do not set up the seatback table. Do not sit on or place anything on the seatback table.NOTICE To prevent damage to the seatback tableDo not put heavy loads on the table. : If equipped388 17. 3-7. Other interior featuresFloor matUse only floor mats designed specifically for vehicles of the samemodel and model year as your vehicle. Fix them securely in placeonto the carpet.Insert the retaining hooks(clips) into the floor mat eye-lets.3Turn the upper knob of eachretaining hook (clip) to secure Interior and exterior features* the floor mats in place.*: Always align the marks.The shape of the retaining hooks (clips) may differ from that shown in theillustration. 389 18. 3-7. Other interior featuresCAUTIONObserve the following precautions.Failure to do so may cause the drivers floor mat to slip, possibly interferingwith the pedals while driving. An unexpectedly high speed may result or it maybecome difficult to stop the vehicle, leading to a serious accident. When installing the drivers floor mat Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. Only use floor mats designed for the drivers seat. Always install the floor mat securely using the retaining hooks (clips) pro- vided. Do not use two or more floor mats on top of each other. Do not place the floor mat bottom-side up or upside-down. Before driving Check that the floor mat is securely fixed in the correct place with all the provided retaining hooks (clips). Be especially careful to perform this check after cleaning the floor. With the engine stopped and the shift lever in P (automatic transmission) or N (manual transmission), fully depress each pedal to the floor to make sure it does not interfere with the floor mat.390 19. 3-7. Other interior featuresLuggage compartment featuresBehind the rear seat (Double Cab models only) 3Cargo net hooks (vehicles with sub woofer)Interior and exterior featuresGrocery bag hooksFlashlight holderStorage boxesDeckAuxiliary boxesTie-down cleatsDeck hooks391 20. 3-7. Other interior featuresAuxiliary boxesLeft sideTurn the knob counterclock-wise.Open the lid.Right side (vehicles without 120V power outlet)Turn the knob counterclock-wise.Open the lid.Right side (vehicles with 120V power outlet)Turn the knob counterclock-wise.Open the lid.392 21. 3-7. Other interior features CAUTION Caution while driving Keep the auxiliary boxes closed and locked. Injuries may result in the event of an accident or sudden braking. Deck hooks Deck hooks are provided for securing loose items. 3Interior and exterior features CAUTION When not in use Keep the deck hooks folded. 393 22. 3-7. Other interior featuresTie-down cleats The deck rail system enables you to insert and move tie-down cleats to their best location along deck rails to secure a load.Locking plateThumb wheelTie-down cleat Installing the tie-down cleat Loosen the thumb wheel in a counterclockwise motion, and depress the wheel so that the locking plate maintains 0.5 in. (12.7 mm) gap. 0.5 in.Deck rail (12.7 mm)DetentLocking plate394 23. 3-7. Other interior featuresInsert the locking plate into thedeck rail, rotate the tie-downcleat 90, and release the thumbwheel.Slide the cleat to the closestdetent in the rail system. You willfeel that the locking plate snapsinto a detent. 3Interior and exterior featuresTighten the thumb wheel in aclockwise motion until the clutchmechanism ratchets.Check the tie-down cleat to con-firm that it is locked into a detentand securely mounted to thedeck rail system. 395 24. 3-7. Other interior features CAUTION Tie-down cleat precautions Properly install and tighten the tie-down cleats into the deck rail system. Failure to properly install and tighten the tie-down cleats can cause cargo to become unsecured. Unsecured cargo can cause injury when the vehi- cle is in motion. Properly secure all cargo to prevent shifting or sliding during driving. Failure to properly secure cargo can cause injury when the vehicle is in motion. Applying loads at an angle to the tie-down cleat greater than 45 or loads greater than 220 lb. (100 kg) may cause damage to the deck, deck rail system, tie-down cleat and/or the cargo. Do not exceed a total tensile load of 440 lb. (200 kg) per deck rail. Do not install more than the following number of tie-down cleats per deck rail: Side rail:Short deckMax. 3 locationsLong deckMax. 4 locations Headboard rail: Max. 3 locationsStorage boxes (Double Cab models only) Storage box is designed to place things like bottles.Right side (vehicles without sub woofer)396 25. 3-7. Other interior featuresLeft side Removing the separatorRemove the separator.3It can be installed in various positions asrequired.Interior and exterior features Flashlight holder (Double Cab models only)Flashlight holder is designed tohold the flashlight securely. 397 26. 3-7. Other interior features Removing the flashlight holderRemove the flashlight holder.It can be installed in various positions asrequired.Grocery bag hooks (Double Cab models only)Grocery bag hook is designed tohang things like grocery bag.NOTICE Grocery bag hook weight capacity Do not hang any object heavier than 7 lb. (3 kg) on the grocery bag hooks.398 27. 3-7. Other interior features Cargo net hooks (Double Cab models with sub woofer)Cargo net hooks are designed tohang the factory-supplied cargonet.NOTICE3 To prevent damage to the cargo net hook Do not hang items other than the cargo net. Interior and exterior features399 28. 3-7. Other interior featuresGarage door openerThe garage door opener can be trained to operate garage doors,gates, entry doors, door locks, home lighting systems, security sys-tems, and other devices.The training procedure is displayed on the inside rear view mirrordisplay screen.The garage door opener (HomeLink Universal Transceiver) is manufac-tured under license from HomeLink. Training the HomeLink (for U.S. owners)The HomeLink compatible transceiver in your vehicle has 3 buttonswhich can be trained to operate 3 different devices. Refer to the train-ing method below appropriate for the device.Indicator lightButtons: If equipped400 29. 3-7. Other interior features Training the HomeLink Point the remote control trans- mitter for the device 1 to 3 in. (25 to 75 mm) from the HomeLink control buttons. Keep the indicator on the HomeLink in view while training. Press and hold down one of the buttons on the HomeLink and the button on the transmitter. 3 When the indicator on the HomeLink changes from a slow Interior and exterior features to a rapid flash, you can release both buttons. If the HomeLink indicator comes on but does not flash, or flashes rapidly for 2 seconds and remains lit, the HomeLink button is already trained. Use the other buttons or follow the Retraining a HomeLink button instructions. (P. 405)401 30. 3-7. Other interior featuresTest the operation of theHomeLink by pressing thenewly trained button. If training a garage door opener, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the Rolling Code type. Press and hold the trained HomeLink button. The garage door has the rolling code feature if the indicator (on the HomeLink) flashes rapidly for 2 seconds and then remains lit. If your transmitter is the Rolling Code type, proceed to the heading Training a rolling code system.Repeat the steps above to train another device for each of theremaining HomeLink buttons.402 31. 3-7. Other interior features Training a Rolling Code system (for U.S. owners)If your device is Rolling Code equipped, follow the steps under theheading Training the HomeLink before proceeding with thesteps listed below.Locate the learn button on the ceiling mounted garage dooropener motor. The exact location and color of the button mayvary by brand of garage door opener.Refer to the operation manual supplied with the garage door openerfor the location of the learning button.Press the learning button.Following this step, you have 30 seconds in which to initiate step 3below.3Press and hold the vehicles trained HomeLink button for 2seconds and release it. Repeat this step once again. The Interior and exterior featuresgarage door may open.If the garage door opens, the training process is complete. If thedoor does not open, press and release the button a third time. Thisthird press and release will complete the training process by openingthe garage door.The ceiling mounted garage door opener motor should now recog-nize the HomeLink transceiver and operate the garage door.Repeat the steps above to train another rolling code systemfor any of the remaining HomeLink buttons.403 32. 3-7. Other interior features Training an entry gate (for U.S. owners)/Training a device in the Canadian marketPlace the remote control transmitter 1 to 3 in. (25 to 75 mm)away from the HomeLink buttonsKeep the HomeLink indicator light in view while training.Press and hold the selected HomeLink button.Repeatedly press and release (cycle) one of the buttons onthe remote control transmitter for 2 seconds at a time until is completed.When the HomeLink indicator light starts to flash rapidly,release the buttons on the HomeLink.Test the HomeLink operation by pressing the newly trainedbutton. Check to see if the gate/device operates correctly.Repeat the steps above to train another device for any of theremaining HomeLink buttons. Training other devicesTo train other devices such as home security systems, home doorlocks and lighting, contact your Toyota dealer for assistance. Retraining a buttonThe individual HomeLink buttons cannot be erased but can beretrained. To retrain a button, follow the Retraining a HomeLinkbutton instructions.404 33. 3-7. Other interior featuresOperating HomeLinkPress the appropriate HomeLink button. The HomeLink indicatorlight should come on.The HomeLink compatible transceiver in your vehicle continues to senda signal for up to 20 seconds as long as the button is pressed.Retraining a HomeLink buttonPress and hold the desired HomeLink button. After 20 seconds, theHomeLink indicator light will start flashing slowly. Keep pressing theHomeLink button and then follow the Training the HomeLink (forU.S. owners) instructions. (P. 400) 3Erasing the entire HomeLink memory (all three programs) Interior and exterior features Press and hold down the 2 out- side buttons for 10 seconds until the indicator flashes. If you sell your vehicle, be sure to erase the programs stored in the HomeLink memory.405 34. 3-7. Other interior features Before training Install a new battery in the remote control transmitter. The battery side of the remote control transmitter must be pointed away from the HomeLink button. Certification for the garage door openerFCC ID: NZLGHSHL4For vehicles sold in the U.S.A.NOTE:This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device maynot cause harmful interference, and (2) this device must accept any inter-ference received, including interference that may cause undesired opera-tion.FCC WARNING:Changes or modifications not expressly approved by the party responsi-ble for compliance could void the users authority to operate the equip-ment.For vehicles sold in CanadaNOTE:Operation is subject to the following two conditions: (1) this device maynot cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device.406 35. 3-7. Other interior features If the following message is displayed This message appears when training procedures have not been performed correctly. Follow the instructions on the screen to complete or cancel train- ing.Pattern APattern B3Interior and exterior features When support is necessary Visit on the web at www.homelink.com or call 1-800-355-3515. 407 36. 3-7. Other interior featuresCAUTION When training a garage door or other remote control devices The garage door or other devices may operate, so ensure people and objects are out of danger to prevent potential harm. Conforming to federal safety standards Do not use the HomeLink compatible transceiver with any garage door opener or device that lacks safety stop and reverse features as required by federal safety standards. This includes any garage door that cannot detect an interfering object. A door or device without these features increases the risk of death or serious injury.408 37. 3-7. Other interior featuresCompass (vehicles with auto anti-glare inside rear view mirror)The compass on the inside rear view mirror indicates the direction inwhich the vehicle is heading. LocationType A 3Type BInterior and exterior features409 38. 3-7. Other interior features Displays and directions Display Direction N NorthNE Northeast E EastSE Southeast SSouthSW SouthwestWWest NWNorthwest410 39. 3-7. Other interior featuresCalibrating the compass 3The direction display deviates from the true direction determined byInterior and exterior featuresthe earths magnetic field. The amount of deviation varies dependingon the geographic position of the vehicle.If you cross over one of the map boundaries shown in the illustration, thecompass will deviate.To obtain higher precision or perfect calibration, refer to Deviationcalibration.Turning the compass display on/offThe compass display on the inside rear view mirror can be turnedon/off and the country and region settings can be changed. Type A: Press and holdto display Custom Settings Menu. Type B: Press to display Custom Settings Menu. 411 40. 3-7. Other interior featuresType A: Press and selectCompass, then pressand hold.Type B: Press and selectCompass, then press.Type A: Press and selectCompass Display.Type B: Press and selectCompass Display.Type A: Press and holdand select display on/off.Type B: Press and select display on/off.To leave the Compass Settings Menu, select Back to mainmenu to return to the starting screen, then either select Exitor wait several seconds without pressing any buttons.Deviation calibrationStop the vehicle.Type A: Press and holdto display Custom SettingsMenu.Type B: Press to display Custom Settings Menu.Type A: Press and selectCompass, then pressand hold.Type B: Press and selectCompass, then press.412 41. 3-7. Other interior featuresType A: Pressand selectZone, then press andhold .Type B: Press and selectZone,then press.Type A: The selected countrychanges each time is pressed.Select the country, thenpress and hold toconfirm. 3Type B: The selected countryInterior and exterior featureschanges each time is pressed.Select the country, thenpress to confirm.Type A: The selected regionchanges each time is pressed.Select the region, thenpress and holdtoconfirm.Type B: The selected regionchanges each timeis pressed.Select the region, thenpressto confirm.To leave the Compass Settings Menu, select Back to mainmenu to return to the starting screen, then either select Exitor wait several seconds without pressing any buttons. 413 42. 3-7. Other interior featuresCircling calibration If C appears on the display, circling calibration needs to be per- formed.Stop the vehicle in a place where it is safe to drive in a circle.Type A: Press and hold to display Custom SettingsMenu.Type B: Pressto display Custom Settings Menu. Type A: Press and select Compass, then press and hold. Type B: Press and select Compass, then press . Type A: Press and select Calibrate, then press and hold. Type B: Press and select Calibrate, then press . C appears on the display.414 43. 3-7. Other interior featuresDrive the vehicle at 5 mph (8km/h) or less in a circle until adirection is displayed.If there is not enough space todrive in a circle, drive around theblock until a direction is dis-played. To leave the Compass Settings Menu, select Back to main menu to return to the starting screen, then either select Exit or wait several seconds without pressing any buttons. 3 Conditions unfavorable to correct operation The compass may not show the correct direction in the following conditions:Interior and exterior features The vehicle is stopped immediately after turning. The vehicle is on an inclined surface. The vehicle is in a place where the earths magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.). The vehicle has become magnetized. (There is a magnet or metal object near the inside rear view mirror.) The battery has been disconnected. A door is open. 415 44. 3-7. Other interior featuresCAUTION While driving the vehicle Do not adjust the display. Adjust the display only when the vehicle is stopped. When doing the circling calibration Secure a wide space, and watch out for people and vehicles in the vicinity. Do not violate any local traffic rules while performing circling calibration.NOTICE To avoid the compass malfunctions Do not place magnets or any metal objects near the inside rear view mirror. Doing this may cause the compass sensor to malfunction. When doing the circling calibration Do not perform a circling calibration of the compass in a place where the earths magnetic field is subject to interference by artificial magnetic fields. During calibration, do not operate electric systems (power windows, etc.) as they may interfere with the calibration.416