2010 Trailer Tow - fordservicecontent.com · 2010 Escape/Mariner Trailer Tow Manual Table of...

2007 - CMY Edge/MKX Trailer Tow

Manual Table of Contents

TRAILER TOWCONTENTS

INSTALLATIONTrailer Tow

GENERAL PROCEDURESProper Splicing Techniques

Contents SKAL8J-15A416-A Copyright Ford 2010 FoMoCo

2007 - CMY Edge/MKX Trailer Tow 1

INSTALLATION

Trailer Tow

Edge/MKX

1. Verify correct kit number.

Review Trailer Tow Installation Kit Contents

Vehicle Preparation

3. Fold both rear seat backrests forward.

4. Remove the rear cargo load area.

Remove the foam blocks from the spare tirewell.2. Review Trailer Tow Installation Kit Contents

Trailer Tow Installation Kit

QUANTITY DESCRIPTION

1 TRAILER TOWCONVERTER HARNESS

ASSEMBLY

1 POWER CABLE WITHIN-LINE FUSE

12 ZIP TIES

Page 1 of 6 SKAL8J-15A416-A Copyright Ford 2010 FoMoCo

2007 - CMY Edge/MKX Trailer Tow 2 INSTALLATION (Continued)

All Vehicles5. Remove the liftgate scuff plate.

Pull upward to release the retaining clips.8. NOTE: Inspect the safety belt lower anchor

Vehicles With Power Liftgate bolt cover for damage. If the safety belt loweranchor bolt cover does not remain in place,install a new cover.6. Remove the cover and the switch from the LH

quarter trim panel. Remove the safety belt lower anchor bolt coverand remove the safety belt lower anchor bolt. Disconnect the electrical connector. To install, tighten to 54 Nm (40 lb-ft).

9. NOTE: Make sure the pushpin retainers areremoved with the quarter trim panels.

Remove the RH and LH quarter trim panels.

Disconnect the electrical connectors, ifequipped.

Remove The Subwoofer Speaker - IfEquipped

NOTE: MKX shown Edge similar.

10. Remove the 3 bolts and the subwoofer speaker.

Disconnect the electrical connector.7. Remove the power liftgate rod-to-liftgate nutcover and nut. To install, tighten the bolts to 7 Nm (62

lb-in). To install, tighten to 11 Nm (97 lb-in).



NOTICE: To avoid any damage to the scuffplate trim panel, remove any retaining clipsfrom the body prior to installation.

NOTE:

NOTE: Install the Trailer Tow Converter Harness Assembly

! "#



Identify Circuit Wires For Connections

NOTE: $ %&

' $(()((&*+ ,-,& or Blue *.+ converter w*/'((0/'(+1 $("2340&

*/'((0/'(+

$("232560& -& or blue

*/'((0'(+1

) NOTE: #1782 (7 . 8$$7

. &89# . 8$$

. &89$(()((4-25607-:& *".!(+0*"'+ $("2340

34-/9 *",'($+ $("232560

34-/9 *",'(+

; $(()((4-2560 *+ converter - &

*".!(+0*"'+ $("2340

*+ converter 34-/9 *",'($+

$("232560 *+ converter 34-/9 *",'(+

= NOTE: #1782 (70 7 2. 4$>9#

0 2. 4$>9$(()((4-2560/-, - *".;+ 0*"'+ $("2340

/3-8/ *".!#+ $("232560

/3-,9 *".;+

? NOTE: #1782 (70 7

0 &$("234034-/9 *".'!+

@ $("2340-&

34-/9*".'!+



( $(()((4-2560 * + converter

/-, - *".;+0*"'+ $("2340

* + /3-8/ *".!#+

$("232560 * + /3-,9 *C.;+

NOTE: #1782 (70 7 2. A/>9#

0 2. A/>9$(()((4-2560-- *".=+#0*"'?+

! $0 $("2340 &/9-8/ *".)#+0 $("232560 & converter7-8/ *".=+

$(()((4-2560* + converter-- *".=+0*"'?+ $("2340*

+ " *+ /9-8/*".)#+

$("232560' " *,

+ converter* +

"*+ 7-8/*".=+



? NOTE: ,

B,D*,B,+NOTE: (9*)!)+%" *,B,+

Install Trim

) 7

Secure Wires

@ >E


2010 Escape/Mariner Trailer Tow


TRAILER TOWCONTENTS



Contents SKAL8J-15A416-A

2010 Escape/Mariner Trailer Tow 1

INSTALLATION

Trailer Tow

Escape/Mariner



Vehicle Preparation

3. Remove the LH front door scuff plate trimpanel.

4. Remove the LH cowl trim panel.

2. Review Trailer Tow Installation Kit Contents 5. Position aside the lower LH front door weatherseal.




ASSEMBLY


12 ZIP TIES

Page 1 of 4 SKAL8J-15A416-A

2010 Escape/Mariner Trailer Tow 2 INSTALLATION (Continued)

Install the Trailer Tow Converter Harness6. Remove the LH rear door scuff plate trimAssemblypanel.

1 Open the rear door scuff plate trim panel11. Place the Trailer Tow Converter Harnessaccess cover and remove the rear door scuff

Assembly in the vehicle forward of the rear LHplate trim panel pin-type retainer.D-pillar using the double sided tape attached to

2 Remove the rear door scuff plate trim panel. the converter module.

7. Remove the liftgate scuff plate.

Remove the rear cargo mat and remove theliftgate scuff plate.

Identify Circuit Wires For Connections

NOTE: For proper wire splicing techniques clickhere.

8. Position the liftgate weatherstrip aside.NOTE: For ease of splicing, pull the grommet

9. If equipped, remove the cargo net hold-down. through the access hole and route the module wiresto the outside of the rear lamp housing.

10. NOTE: Insert a non-marring tool between theNOTE: Make connections on the interior side ofD-pillar trim panel and rear quarter trim panelthe grommetto release the trim panel.

NOTE: LH rear quarter trim panel shown, RH12. Connect the Black (Ground) wire and the

Blue/Black B(Stop) wire from the convertermoduleto the ground screw (G401-G402) near the LHD-pillar

similar.

Remove the rear quarter trim panels.



17. NOTE: A DVOM connected to the correct wirewill show 0V, then show pulsing 12V when theMultifunction Switch in the RIGHT TURNposition.

A logic probe will show ground on the correctwire, then show pulsing power when theMultifunction Switch in the RIGHT TURNposition.

Identify the Violet/Orange right turn/stop circuitwire (CLS19) at the Lamp Assembly, RightRear (C4032).

18. Route the Green (Right Turn) wire from the13. NOTE: A DVOM connected to the correct wireconverter module harness under the liftgate scuffwill show 0V with the Headlight Switch in theplate and connect to the Violet/Orange rightOFF position and 12V with the Headlightturn/stop circuit wire (CLS19) at the LampSwitch in the parking lights ON position.Assembly, Right Rear (C4032).

A logic probe connected to the correct wire willshow ground with the Headlight Switch in the 19. From the engine compartment, route the RedOFF position and power with the Headlight power cable through the bulkhead into theSwitch in the parking lights ON position. passenger compartment, along the LH door sills

back to the converter module.Identify the Violet/White parking lights circuitwire (CLS30) at the Lamp Assembly, Left Rear(C4035).

14. Connect the Brown (Tail Lamp) wire from theconverter module harness to the Violet/Whiteparking lights circuit wire (CLS30) at the LampAssembly, Left Rear (C4035).

15. NOTE: A DVOM connected to the correct wirewill show 0V, then show pulsing 12V when theMultifunction Switch in the LEFT TURNposition.

A logic probe will show ground on the correctwire, then show pulsing power when theMultifunction Switch in the LEFT TURN

20. Connect the Red (Battery) wire from the converterposition.module harness to the Red power cable.

Identify the Gray/Brown left turn/stop circuitwire (CLS18) at the Lamp Assembly, Left Rear 21. NOTE: Remove in-line fuse before connecting(C4035). the power cable to the Battery Junction Box

(BJB)16. Connect the Yellow (Left Turn) wire from the

Connect the Red power cable to the (BJB)converter module harness to the Gray/Brown leftbattery terminal.turn/stop circuit wire (CLS18) at the Lamp1 Tighten to 10 Nm (7.37 lbs.ft.).Assembly, Left Rear (C4035).2 Replace the in-line fuse.



Secure Wires Install Trim

22. Use supplied zip ties to secure power cable and 23. Reverse Vehicle Preparation steps to reinstallwires to vehicle harness. trim panels.



TRAILER TOWCONTENTS



NOTE: This accessory kit is designed to be used as a Class 1 trailer tow wiring solution.

NOTE: A

7&

!"#

A5"

#A48:"89744#94..

#..42,3 8:4"#,4:A

A9A94$>.4 FAA4.

! 8

' &-D

?

@

)

;

=

(

A%0

!"#

A%0 E

NOTE: $ %&! E

' NOTE: A 1 %

NOTE: % 0 %

=

? # - G 11

@ 1 -

) :& ( 0-

; " ,-,&*.+ # 1Do not attach the Trailer TowConverter at this time. " ,&*/+

1H

$

!"$#

! NOTE: #1782 (7 ,&

7 , ,&

,&A 7-/*.+ #0

' " ,*.+ 7-/*.+

? NOTE: #1782 (7 . 8$$7

. &89# . 8$$

. &89A 7-/*&"+ #0

@ " , *+ 7-/*&"+ #0

) NOTE: #1782 (70 7 2. 4$>9#

0 2. 4$>9A /-8*"+ #0

; " 3 *+ /-8*"+ #0

= NOTE: #1782 (70 7 2. A/>9#

0 2. A/>9A /-8*"+ #0

!( /*+ /-8*"+ #0

! #0 &G

! # 0 &

!! $0

&

*

+

&0*

+&

!' #0

&

!? 1

!"#

!@ #0 != A - & 0 0'

H

'( . -

' &

' 7% 0

G

1

!) NOTE: $B" $B

$B

'! 7% 0

A $B

! ?(9*''+

' '' #0

'-

!; #0 ' G 1

!"#

'? >E '@ >E

') . '- Secure harness awayfrom sharp edges, moveable parts or highheat sources.

'; 7

!"#

2009 - CMY Flex Trailer Tow


TRAILER TOWCONTENTS


GENERAL PROCEDURES Proper Splicing Techniques

Contents SKAL8J-15A416-A

2009 - CMY Flex Trailer Tow 1

INSTALLATION

Trailer Tow

Flex

NOTICE: Trailer tow converter kit is only applicable to vehicles not equipped with factory trailer tow



2. Review Trailer Tow Installation Kit Contents




ASSEMBLY


12 ZIP TIES


2009 - CMY Flex Trailer Tow 2 INSTALLATION (Continued)

Vehicle Preparation

3. Remove the LH scuff plate and cowl trimpanel.

Pull upward on the scuff plate trim panel torelease the retainer clips.

4. Remove the LH and RH rear door scuff plates.

Pull upward on the scuff plate to releaseclips.

7. Remove the LH and RH upper C-pillar trimpanel bolt.

5. Remove the LH lower B-pillar trim panel.

Pull outward on the trim panel to release theclips.

8. Remove the LH and RH safety belt anchor bolt.

To install, tighten to 40 Nm (30 lb-ft).

6. Remove the LH and RH upper C-pillar trimpanel bolt cover.

9. Pull outward to release the C-pillar trim panelclips.

10. Reposition the safety belt through the C-pillartrim panel.



11. Remove the LH and RH upper C-pillar trim 15. Remove the LH and RH D-pillar trim panels.panels. Pull forward on the D-pillar trim panel to

release the front clips.12. Remove the LH and RH D-pillar safety belt

Pull downward on the D-pillar trim panel toanchor bolts.release the upper clip.

To install, tighten to 40 Nm (30 lb-ft).

16. Reposition the safety belt thru the D-pillar trimpanels.

17. Position aside the liftgate weatherstrip.

18. Remove the liftgate scuff plate pin-typeretainers.

13. Open the LH and RH D-pillar trim panel boltcovers.

19. Remove the liftgate scuff plate.

Pull upward to release the retaining clips.

14. Remove the LH and RH D-pillar trim panelbolts.



20. Remove the LH and RH quarter trim panelretaining screws.

25. Remove the power liftgate rod retaining nut.

To install, tighten to 11 Nm (97 lb-in).

21. Position the second row seats in the flatposition and then tilt the second row seatsforward.

22. Position the third row seats in the flat position.

23. Remove the cargo net retaining hooks.

26. Remove the power liftgate rod from the liftgate.

27. Remove the power liftgate rod cover.

Pull the power liftgate rod cover outward torelease the power liftgate rod cover clips.

Disconnect the electrical connector.

Vehicles with a power liftgate

24. Remove the power liftgate rod retaining nutcover.

28. Position the liftgate rod to the full downposition.



29. Remove the quarter trim panel.

Pull the quarter trim panel toward the insideof the vehicle to release the retaining clips.

If equipped, disconnect the electricalconnectors.

Maneuver the quarter trim panel over thethird row seat and over the power liftgaterod.

Vehicles without a power liftgate

30. Remove the LH and RH quarter trim panel.Identify Circuit Wires For Connections

Pull the quarter trim panel toward the insideof the vehicle to release the retaining clips.

NOTE: For proper wire splicing techniques click If equipped, disconnect the electrical here.

connectors.NOTE: For ease of splicing, pull the grommet

Remove the Rear Lamp Assemblies through the access hole and route the module wiresto the outside of the rear lamp housing.

31. NOTE: The rear lamp assembly is held inNOTE: Make connections on the interior side ofplace by snap-type retainers. The lamp shouldthe grommetbe pulled straight and rearward to remove.

Remove the 2 screws and the rear lamp 33. NOTE: A DVOM connected to the correct wireassembly. will show 0V with the Headlight Switch in the Disconnect the electrical connectors and OFF position and 12V with the Headlight

separate the bulb holders from the rear lamp Switch in the parking lights ON position.assembly. A logic probe connected to the correct wire will

show ground with the Headlight Switch in theOFF position and power with the HeadlightSwitch in the parking lights ON position.

Identify the Violet/White parking lights circuitwire (CLS30) at the Lamp Assembly, Left Rear(C498).

34. Connect the Brown (Tail Lamp) wire from theconverter module harness to the Violet/Whiteparking lights circuit wire (CLS30) at the LampAssembly, Left Rear (C498).

Install the Trailer Tow Converter HarnessAssembly

32. Place the Trailer Tow Converter HarnessAssembly in the vehicle forward of the rear LHD-pillar and just behind the auxiliary climateconverter housing using the double sided tapeattached to the converter module.



!? NOTE: #1782 (70 7 2. 4$>9#

0 2. 4$>9A /-, -

*".;+#0*"'=;+

!@ " 3 *+ /-, - *".;+#0*"'=;+

!) NOTE: #1782 (70 7 2. A/>9#

0 2. A/>9A 7-8- != " ,&*/+ *".=+#0 ,-,&*.+ *"'==+ */!(+

1!; /*+

'( $07-8- & *".=+#0 0*"'==+ &


2009 - CMY Flex Trailer Tow 7INSTALLATION (Continued)

Secure Wires' " *,

+ '! >E

' NOTE:

,

B,D*,B,+ Secure converter boxNOTE: (9*)!)+%

'' & " *,B,+

'? 7


& ''$

()*+,-*,./,)

0

1 0$

2

3 0

!

2

Splicing Procedures 2

Page 2 of 9 Copyright Ford 2012 FoMoCo

4+&,05(I)6I

6(07-3&+184%.

9

&:-3%1.;

8 )-.

'$

;>;

--.-".

!"#$%'" ":-%9".0C%&:-81.0C"$

2010 Trailer Tow - fordservicecontent.com · 2010 Escape/Mariner Trailer Tow Manual Table of...

Documents

Transcript of 2010 Trailer Tow - fordservicecontent.com · 2010 Escape/Mariner Trailer Tow Manual Table of...