2007 DIESEL EMISSION STANDARDS IMPLICATIONS

FOR FLEET OPERATORS

automotive fleet & leasing association white paper series ∙ volume 3

Since January 1, 2007, the Environmental Protection Agency (EPA) has mandated that all diesel engines used in heavy-duty highway vehicles comply with more stringent emission standards.

Specifically, the EPA has defined “heavy-duty highway vehi-cles” as vehicles of gross vehicle weight ratings (GVWR) above 8,500 lbs. (above 14,000 lbs. in California). Personal transpor-tation vehicles up to 10,000 lbs. such as larger sport/utility ve-hicles and passenger vans have been re-classified as “medium-duty passenger vehicles” and are not subject to the heavy-duty vehicle legislation. This report focuses on the implications of the 2007 requirements for heavy-duty highway vehicles.

The 2007 standards include a 50 percent reduction in the various nitrogen oxides produced during combustion (NOx) and a 90 percent reduction in particulate matter emissions com-pared to the 2004 standards. The regulation requires on-vehicle monitoring of the performance of the engine’s emissions system. The industry standard is called Engine Manufacturer Diagnostics (EMD) and will detect issues within the emissions control system and inform the driver with indicator lights on the dashboard.

Since engine changes alone cannot meet the new require-ments, the new “clean diesel” technologies include improved electronic control systems, ultra-low sulfur diesel (ULSD), exhaust after treatment such as catalytic converters and diesel particu-late filters (DPF), enhanced exhaust gas recirculation (EGR), cooling system changes (due to higher heat loading) and fuel/air ratio changes.

The new diesel fuel formulation limits the sulfur content in on-highway diesel fuel to 15 parts per million (ppm) down from 500 ppm. The EPA ordered that at least 80 percent of the diesel fuel sold in the U.S. after Oct. 15, 2006 contain no more than 15 ppm of sulfur with a phased in approach to 100 percent compliance by 2010.

ULSD has been introduced as a “technology enabler” to pave the way for advanced, sulfur-intolerant exhaust emission control technologies, such as DPFs, which are necessary to meet the 2007 emission standards.

DPFs have been in development for more than 15 years and are used to filter exhaust particulates. The combustible materials (soot) that are filtered from the exhaust require a regeneration cycle that is dependent upon idle time and engine usage. Prop-erly configured engines and drivelines are important to enable exhaust systems to run hotter and thereby minimize regeneration cycles.

The average active regeneration cycle will occur once or twice

daily, burning approximately one-half gallon of fuel to raise the DPF temperature to 1,100-1,300 degrees F for 20 minutes. At these temperatures, it is important for the DPF to be properly insulated including exhaust pipe exit temperature reduction tech-nology to lower temperatures to acceptable levels.

The life of the DPF will be substantially reduced if non-ULSD is used. Typically, DPFs need to be cleaned of noncombustible materials (“ash” that comes from the unburned detergents form engine oil) every 150,000 to 200,000 miles using an exchange program or “clean it on the truck” process which are estimated to cost between $150 and $400.

As with any new technology, there remain a number of unanswered questions. However, early indications from several fleets report the vehicles with 2007 engines have run as well, if not better, than previous engines in terms of performance, fuel consumption, reliability, and maintenance.

What Are Some Considerations for Your Fleet Today?Acquisition cost increases of $5,000 to $13,000 per truck for

the 2007 engine emissions (2008-MY) excluding possible incen-tives to help mitigate these increases.

ULSD will be formulated for backwards compatibility for older models and has a reduced BTU content of 1 to 3 percent, de-creasing fuel efficiency.

EPA Clean Air Act rules by 2010 are calling for the virtual elimination of nitrogen oxides (about 85 percent reduction from the current 2007 allowable nitrogen oxide levels).

Starting in 2010, diesel trucks may have to fill a supplementa-ry tank with urea, an organic compound that significantly reduces nitrogen oxide emissions when injected into the vehicle’s exhaust system.

New low-ash/reduced-sulfur engine oils are compatible with low-emissions solutions to minimize DPF service. Drain intervals may be affected by soot loading of the oil.

Crankcase vent filters will require maintenance once per year.The replacement cost of the DPF is estimated to be $3,000 to

$4,000 with PDF theft a real concern as approximately $1,800 in precious metals is contained within the filter.

The fragile ceramic DPF will weigh about 100 to 120 pounds, and may be difficult for some to handle.

Heat loads to be 10 to 30 percent higher, potentially reduc-ing the life of engine components such as fan belts and hoses.

Heavy-duty Class 8 trucks are expected to have a fuel economy decline of 0 to 1 percent, while medium-duty engines

2007 Diesel Emission Standards Implications for Fleet Operators

By GE Capital Solutions Fleet Services

are reported to have a 0 to 4 percent improvement. Larger diameter DPFs (15 to 22 inches) and exhaust tem-

perature reduction technologies are located behind the cab or on the curb side frame rails requiring additional clearances and introducing potential interference issues.

Any modifications to the exhaust piping will not be allowed before the location of the DPF.

This information is intended as a general overview only. For more information, please contact your OEM and engine manufacturers. Additional information may be found on these industry web sites: NTEA.com; dieselnet.com and epa.gov/otaq/hwy.htm

Source: Environmental Protection Agency’s Code of Federal Regula-tions 40CFR86, Subpart A (Control of Emissions from New and In-Use Highway Vehicles and Engines – General Provisions for Emission Regulations for 1977 and Later).