READ THIS MANUALCAREFULLY BEFORE OPERATION!

OWNER’S/OPERATOR’SMANUAL

LIT-18626-04-01

XLT1200

U.S.A. Edition

2001

WaveRunner

E

EJU00270

To the owner/operatorThank you for choosing a Yamaha water-

craft. This Owner’s/Operator’s Manual contains

information you will need for proper opera-tion, maintenance, and care. A thoroughunderstanding of these simple instructionswill help you to obtain maximum enjoymentfrom your new Yamaha. If you have anyquestions about the operation or mainte-nance of your watercraft, please consult aYamaha dealer.

Because Yamaha has a policy of continu-ing product improvement, this product maynot be exactly as described in this Owner’s/Operator’s Manual. Specifications are sub-ject to change without notice.

This manual should be considered a per-manent part of this watercraft and shouldremain with it even if the watercraft is subse-quently sold.

Important manual information:In this manual, information of particular

importance is distinguished in the followingways:

The Safety Alert Symbol meansATTENTION! BECOME ALERT!YOUR SAFETY IS INVOLVED!

WARNINGFailure to follow WARNING instructionscould result in severe injury or death tothe machine operator, passenger(s), abystander, or a person inspecting orrepairing the watercraft.

CAUTION:A CAUTION indicates special precau-tions that must be taken to avoid damageto the watercraft.

NOTE:A NOTE provides key information to makeprocedures easier or clearer.

EJU00271

WaveRunner XLT1200OWNER’S/OPERATOR’S MANUAL

©2000 by Yamaha Motor Corporation, USA1st Edition, November 2000

All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, USA

is expressly prohibited.Printed in USA

P/N LIT-18626-04-01

EEJU00273

CONTENTS

READ THIS OWNER’S/OPERATOR’S MANUAL CAREFULLYBEFORE OPERATING YOUR WATERCRAFT.

GENERAL AND SAFETY INFORMATION 1

FEATURES AND FUNCTIONS 2

OPERATION 3

MAINTENANCE AND CARE 4

TROUBLESHOOTING AND EMERGENCY PROCEDURES 5

APPENDIX 6

E

1

EJU00274

GENERAL AND SAFETY

INFORMATIONIdentification numbers.............................1-1

Primary Identification (PRI-ID) number..1-1Hull Identification Number (HIN).............1-1Engine serial number..............................1-1

Emission control information.................1-2Approval label of Emission control certificate.................................................1-2Manufactured date label.........................1-2

Important labels........................................1-3Label location..........................................1-3Warning labels ........................................1-4Caution labels .........................................1-6Other labels.............................................1-7

Safety information..............................1-8Limitations on who may operate the watercraft.................................................1-8Cruising limitations..................................1-9Operation requirements........................1-10Hazard information ...............................1-13Watercraft characteristics.....................1-13Water-skiing ..........................................1-14

Rules of the Road...................................1-16Steering and sailing rules .....................1-16Rules when encountering vessels .......1-17Other special situations ........................1-18Reading buoys and other markers.......1-18

To get more boating safety information ..............................................1-20

United States Coast Guard ..................1-20Other sources .......................................1-20Watercraft Education and Training.......1-20

Enjoy your watercraft responsibly.......1-21

1-2

E

EJU00631a

Emission control information

This engine conforms to the U.S. Environ-mental Protection Agency (EPA) regulationsfor marine SI engines for the year 2001.

Approval label of Emission control certificate

This label is attached to the electrical boxand the silencer of the carburetor.

1 Emission control information label

Manufactured date labelThis label is attached to the electrical box

and the silencer of the carburetor.

2 Manufactured date label

1-3

E

EJU00293

Important labelsLabel location

1-4

E

Warning labels1

2 3

5

4

1-5

E

6 7

8

9 0

A B

C

1-6

E

Caution labelsD E

F

G H

I J

1-7

E

Other labelsK L

M

N

1-8

E

EJU00686

Safety informationThe safe use and operation of this

watercraft is dependent upon the use ofproper riding techniques, as well as uponthe common sense, good judgment, andexpertise of the operator. Every operatorshould know the following requirementsbefore riding the watercraft.● Before operating the watercraft, read the

Owner’s/Operator’s Manual, the RidingPractice Guide, the Riding Instructioncard and all warning and caution labelson the watercraft. Also, watch the BasicOrientation Video provided with yourwatercraft. These materials should giveyou an understanding of the watercraftand its operation.

● Never allow anyone to operate this water-craft until they too have read the Owner’s/Operator’s Manual, the Riding PracticeGuide, the Riding Instruction card and allwarning and caution labels, and if possi-ble watched the Basic Orientation Video.Showing them the video may help rein-force the information contained in thesematerials.

EJU00667a

Limitations on who may operate the watercraft● Yamaha recommends a minimum opera-

tor age of 16 years old.Adults must supervise use by minors.Know the operator age and trainingrequirements for your state. A boatingsafety course is recommended and maybe required in your state. You can findlocal rules by contacting the UnitedStates Coast Guard (USCG), the NationalAssociation of State Boating Law Admin-istrators, or your local Power Squadron.

● This watercraft is designed to carry theoperator and up to 2 passengers. Neverexceed the maximum load limit or allowmore than 3 persons (or 2 persons if awater-skier is being pulled) to ride thewatercraft at one time.

● Do not operate the watercraft with anypassengers on board until you have con-siderable practice and experience ridingalone. Operating the watercraft with pas-sengers requires more skill. Take the timeto become accustomed to the handlingcharacteristics of the watercraft beforetrying any difficult maneuvers.

Maximum load: 240 kg (530 lb)Load is the total weight of cargo, opera-tor and passengers.

1-9

E

EJU00613

Cruising limitations

● Scan constantly for people, objects, andother watercraft. Be alert for conditionsthat limit your visibility or block your visionof others.

● Operate defensively at safe speeds andkeep a safe distance away from people,objects, and other watercraft.

● Do not follow directly behind watercraft orother boats.

● Do not go near others to spray or splashthem with water.

● Avoid sharp turns or other maneuversthat make it hard for others to avoid you orunderstand where you are going.

● Avoid areas with submerged objects orshallow water.

● Ride within your limits and avoid aggres-sive maneuvers to reduce the risk of lossof control, ejection, and collision.

● This is a high performance boat—not atoy. Sharp turns or jumping wakes orwaves can increase the risk of back/spinalinjury (paralysis), facial injuries, and bro-ken legs, ankles and other bones. Do notjump wakes or waves.

● Do not operate the watercraft in roughwater, bad weather or when visibility ispoor; this may lead to an accident caus-ing injury or death. Be alert to the possi-bility of adverse weather. Take note ofweather forecasts and the prevailingweather conditions before setting out onyour watercraft.

● As with any water sport, you should notride your watercraft without someone elsenear by. If you ride further than swimmingdistance from shore, you should ride byanother boat or watercraft, but make sureyou stay a safe distance away. It’s goodcommon sense!

● Never operate in water that is less than60 cm (2 ft) deep, otherwise you increaseyour chance of hitting a submergedobject, which could result in injury.

1-1

E

EJU00699

Identification numbersRecord your Primary Identification (PRI-

ID) number, Hull Identification Number (HIN)and engine serial number in the spaces pro-vided, to assist you in ordering spare partsfrom a Yamaha dealer. Also record and keepthese ID numbers in a separate place incase your watercraft is stolen.

EJU00700

Primary Identification (PRI-ID) number

The PRI-ID number is stamped on a label 1attached to the inside of the engine compart-ment.

EJU00701

Hull Identification Number (HIN)

The HIN is stamped on a plate 2

attached to the aft deck.

EJU00288a

Engine serial number

The engine serial number is stamped ona label 3 attached to the engine unit.

1-10

E

● This watercraft is not equipped with light-ing required for night operation. Do notoperate the watercraft after sunset orbefore dawn, otherwise you increase therisk of colliding with another boat, whichcould result in severe injury or death.

EJU00735a

Operation requirements● All riders must wear a Coast Guard

approved personal flotation device (PFD)that is suitable for personal watercraftuse.

● Wear protective clothing. Severe internalinjuries can occur if water is forced intobody cavities as a result of falling intowater or being near the jet thrust nozzle.Normal swimwear does not adequatelyprotect against forceful water entry intorectum or vagina. All riders must wear awetsuit bottom or clothing that providesequivalent protection. Such clothingincludes thick, tightly woven, sturdy andsnug-fitting apparel such as denim, butdoes not include spandex or similar fab-rics, like those used in bicycle shorts.

1 Coast Guard approved PFD2 Wetsuit bottom

● Eye protection is recommended to keepwind, water, and glare from the sun out ofyour eyes while you operate your water-craft. Restraining straps for eyewear aremade which are designed to float shouldyour eyewear fall in the water.Footwear and gloves are recommended.

1-11

E

● Helmets meeting Snell or DOT standardsare required for IJSBA-sanctioned races.You must decide whether to wear a hel-met while you ride for recreation. Youshould know that a helmet could help pro-tect you in certain kinds of accidents andthat it could also injure you in others.A helmet is designed to provide somehead protection. Although helmets cannotprotect against all foreseeable impacts, ahelmet might reduce your injuries in a col-lision with a boat or other obstacle.A helmet may have potential safety haz-ards, as well. Falling into the water couldrisk the chance of the helmet catchingwater, commonly known as “bucketing,”and the resulting strain on your neckcould cause choking, severe and perma-nent neck injuries, or death. A helmetcould also increase the risk of an accidentif it reduces your vision or hearing, or if itdistracts you or increases your fatigue.How should you decide if a helmet’spotential safety benefits outweigh itspotential risks for you? Consider your par-ticular riding conditions. Consider factorssuch as your riding environment, yourriding style and your riding ability. Alsoconsider the likelihood of traffic conges-tion, and the water surface conditions. Ifyou decide to wear a helmet based uponyour riding circumstances, choose onecarefully. Look for a helmet designed forpersonal watercraft use, if possible. Con-sider a helmet meeting Snell or DOT stan-dards. If you will be engaging in closed-course competition, follow the helmetrequirements of the sanctioning organiza-tion.

● NEVER operate the watercraft after con-suming alcohol or taking other drugs.

● For reasons of safety and proper care ofthe watercraft, always perform the pre-operation checks listed on page 3-5before operating the watercraft.

● The operator and passengers shouldalways keep both feet in the footwell whenthe watercraft is in motion. Lifting yourfeet increases your chances of losing yourbalance, and your feet being hit by objectsoutside the watercraft. Do not give a rideto children if their feet cannot reach thefloor of the footwell.

● Passengers should firmly hold on to theperson in front of them.

● Always consult your doctor on whether itis safe for you to ride this watercraft if youare pregnant or in poor health.

1-12

E

● Do not attempt to modify this watercraft!Modifications to your watercraft mayreduce safety and reliability, and renderthe watercraft unsafe or illegal for use.

● Attach the engine shut-off cord (lanyard)to wrist and keep it free from the handle-bars so that the engine stops if the opera-tor falls off. After riding, remove theengine shut-off cord from the watercraft toavoid accidental starting or unauthorizeduse by children or others.

● Scan carefully for swimmers and stayaway from swimming areas. Swimmersare hard to see and you could acciden-tally hit someone in the water.

● Avoid being hit by another boat! Youshould always take the responsibility towatch for traffic; other boaters may not bewatching for you. If they do not see you,or you maneuver more quickly than otherboaters expect, you risk a collision.

● Maintain a safe distance from other boatsor watercraft, and also watch for boats’ skiropes or fishing lines. Obey the “Rules ofthe Road,” and be sure to check behindyou before making a turn. (See Rules ofthe Road on pages 1-16 to 1-19.)

● This watercraft is included in the Class Ainboard boat classification of the U.S.Coast Guard. A watercraft of this typeMUST carry a fire extinguisher of a B-1classification, with a capacity of twopounds or more when navigating inwaters under Coast Guard jurisdiction. Inaddition, most state and local boatinglaws also require that the fire extinguisherbe approved by the USCG.

F0P03010

1-13

E

EJU00313

Hazard information

● When transporting or storing your water-craft, always place the fuel cock knob inthe “OFF” position, otherwise gasolinemay overflow from the carburetor.

● Never start the engine or let it run for anylength of time in an enclosed area.Exhaust fumes contain carbon monoxide,a colorless, odorless gas that may causeloss of consciousness and death within ashort time. Always operate the watercraftin an open area.

● Do not start the engine on land untileveryone is away from the stern. Hotwater and steam spurting from exhaustoutlet into the air can cause seriousburns.

● Hot muffler surfaces can cause seriousburns. Do not touch any muffler surfaceduring or after operation. The catalyticconverter gets hotter after the enginestops.

EJU00315a

Watercraft characteristics● Jet thrust turns the watercraft. Releasing

the throttle completely produces only min-imum thrust. If you are traveling at speedsabove trolling, you will have rapidlydecreasing ability to steer without throttle.You may still have some turning abilityimmediately after releasing the throttle,but once the engine slows down, thewatercraft will no longer respond to han-dlebar input until you open the throttleagain or you reach a trolling speed. Prac-tice turning in an open area withoutobstructions until you have a good feel forthis maneuver.

● This watercraft are water-jet propelled.The jet pump is directly connected to theengine. This means that jet thrust will pro-duce some movement whenever theengine is running. There is no “neutral”position. You are in either “forward” or“reverse,” depending upon the shift leverposition.

● Do not use the reverse function to slowdown or stop the watercraft as it couldcause you to lose control, be ejected, orimpact the handlebars.This could increase the risk of back/spinalinjury (paralysis), facial injuries, and bro-ken legs, ankles, and other bones. Youcould also damage the shift mechanism.

1-14

E

● Reverse can be used to slow down orstop during slow speed maneuvering,such as when docking. Once the engineis idling, shift to reverse and graduallyincrease engine speed. Make sure thatthere are no obstacles or people behindyou before shifting into reverse.

● Keep away from intake grate 1 while theengine is on. Items such as long hair,loose clothing, or PFD straps can becomeentangled in moving parts resulting insevere injury or drowning.

● Never insert any object into the jet thrustnozzle 2 while the engine is running.Severe injury or death could result fromcoming in contact with the rotating partsof the jet pump.

● Stop the engine and remove the clip 3from the engine shut-off switch 4 beforeremoving any debris or weeds, which mayhave collected around the jet intake.

EJU00668a

Water-skiingYou can use the watercraft for water-ski-

ing if it has the seating capacity to carry theoperator, a rearward-facing spotter, and thewater-skier when he or she is not skiing.

The watercraft must also have a cleat 5designed to pull a ski tow rope; do not attachthe tow rope to any other location.

It is the watercraft operator’s responsibilityto be alert to the safety of the water-skierand others. Know and follow all state andlocal water-skiing regulations in effect for thewaters in which you will be operating.

The operator should be comfortable car-rying passengers before attempting to pull askier.

The following are some important consid-erations for minimizing risks while water-ski-ing.● The skier should wear an approved PFD,

preferably a brightly colored one so boatoperators can see the skier.

● The skier should wear protective clothing.Severe internal injuries can occur if wateris forced into body cavities as a result offalling into the water. Normal swimweardoes not adequately protect againstforceful water entry into rectum or vagina.The skier should wear a wetsuit bottom orclothing that provides equivalent protec-tion.

1-15

E

● A second person should be on board as aspotter to watch the skier; in most states itis required by law. Let the skier direct theoperator’s control of speed and directionwith hand signals.The spotter should sit securely on thepassenger seat and hold onto the hand-grip with feet firmly on the footrest forproper balance while facing to the rear towatch the skier’s hand signals and his orher condition.

1 Handgrip2 Footrest

● Your control while pulling a skier isaffected by the skier’s ability, as well aswater and weather conditions.

● When preparing to pull a skier, operatethe watercraft at the slowest possiblespeed until the watercraft is well awayfrom the skier and slack in the towrope istaken up. Make sure that the rope is notlooped around anything.After checking that the skier is ready andthat there is no traffic or other obstacles,apply enough throttle to raise the skier.

● Make smooth, wide turns. The watercraftis capable of very sharp turns, whichcould exceed the abilities of the skier.Keep the skier at least 50 m (150 ft),about twice the distance of a standardtowrope, from any potential hazard.

● Be alert to the hazard of the towrope han-dle snapping back at the watercraft whenthe skier falls or is unable to get up on theskis.

● Towing heavy or bulky objects other thanskiers, such as another boat or watercraft,can cause loss of steering control andcreate a hazardous condition. If you musttow another boat in an emergency situa-tion, operate slowly and cautiously.

1-16

E

EJU00319

Rules of the RoadYamaha watercraft is legally consid-

ered a powerboat. Operation of thewatercraft must be in accordance withthe rules and regulations governing thewaterway on which it is used.

Just as there are rules that apply whenyou are driving on streets and highways,there are waterway rules that apply whenyou are operating your watercraft. Theserules are used internationally, and are alsoenforced by the United States Coast Guardand local agencies. You should be aware ofthese rules, and follow them whenever youencounter another vessel on the water.

Several sets of rules prevail according togeographic location, but are all basically thesame as the International Rules of theRoad. The rules presented here in thisOwner’s/Operator’s Manual are condensed,and have been provided for your conve-nience only. Consult your local U.S. CoastGuard Auxiliary or Department of MotorVehicles for a complete set of rules govern-ing the waters in which you will be operatingyour watercraft.

Steering and sailing rulesWhenever two vessels on the water meet

one another, one vessel has the right-of-way; it is called the “stand-on” vessel. Thevessel that does not have the right-of-way iscalled the “give-way” or “burdened” vessel.These rules determine which vessel has theright-of-way, and what each vessel shoulddo.

Stand-on vesselThe vessel with the right-of-way has the

duty to continue its course and speed,except to avoid an immediate collision.When you maintain your direction andspeed, the other vessel will be able to deter-mine how best to avoid you.

Give-way vesselThe vessel which does not have the right-

of-way has the duty to take positive andtimely action to stay out of the way of thestand-on vessel. Normally, you should notcross in front of the vessel with the right-of-way. You should slow down or change direc-tions briefly and pass behind the other ves-sel. You should always move in such a waythat the operator of the other vessel can seewhat you are doing.

The General Prudential Rule regardingthe right-of-way is that if a collision appearsunavoidable, neither boat has the right-of-way. Both boats must avoid the collision.

In other words, follow the standard rulesexcept when a collision will occur unlessboth vessels try to avoid each other. If that isthe case, both vessels become give-wayvessels.

1-17

E

Rules when encountering vessels

There are three main situations that youmay encounter with other vessels whichcould lead to a collision unless the SteeringRules are followed:

Meeting: you are approaching anothervessel head-on

Crossing: you are traveling acrossanother vessel’s path

Overtaking: you are passing or beingpassed by another vessel

In the following illustration, your watercraftis in the center. You should give the right-of-way to any vessels shown in the white area(you are the give-way vessel). Any vesselsin the shaded area must yield to you (theyare the give-way vessels). Both you and themeeting vessel must alter course to avoideach other.

MeetingIf you are meeting another power vessel

head on, and are close enough to run the riskof collision, neither of you has the right-of-way! Both of you should alter course to avoidan accident. You should keep the other ves-sel on your port (left) side. This rule does notapply if both of you will clear one another ifyou continue on your set course and speed.

CrossingWhen two power-driven vessels are

crossing each other’s path close enough torun the risk of collision, the vessel which hasthe other on the starboard (right) side mustkeep out of the way of the other. If the othervessel is on your starboard (right) side, youmust keep out of its way; you are the give-way vessel. If the other vessel is on yourport (left) side, remember that you shouldmaintain course and direction, provided theother vessel gives you the right-of-way as itshould.

1-18

E

OvertakingIf you are passing another vessel, you are

the give-way vessel. This means that theother vessel is expected to maintain itscourse and speed. You must stay out of itsway until you are clear of it. Likewise, ifanother vessel is passing you, you shouldmaintain your speed and direction so thatthe other vessel can steer itself around you.

Other special situationsThere are three other rules you should be

aware of when riding your watercraft aroundother vessels.

Narrow channels and bendsWhen navigating in narrow channels, you

should keep to the right when it is safe andpractical to do so. If the operator of a power-driven vessel is preparing to go around abend that may obstruct the view of otherwater vessels, the operator should sound aprolonged blast of four to six seconds on thewhistle. If another vessel is around the bend,it too should sound the whistle. Even if noreply is heard, however, the vessel shouldstill proceed around the bend with caution. Ifyou navigate such waters with your water-craft, you will need to carry a portable airhorn, available from local marine supplystores.

Fishing vessel right-of-wayAll vessels fishing with nets, lines or

trawls are considered to be “fishing vessels”under the International Rules. Vessels withtrolling lines are not considered fishing ves-sels. Fishing vessels have the right-of-wayregardless of position. Fishing vessels can-not, however, impede the passage of othervessels in narrow channels.

Sailing vessel right-of-waySailing vessels should normally be given

the right-of-way. The exceptions to this are:1. When the sailing vessel is overtaking the

power-driven vessel, the power-drivenvessel has the right-of-way.

2. Sailing vessels should keep clear of anyfishing vessel.

3. In a narrow channel, a sailing vesselshould not hamper the safe passage of apower-driven vessel that can navigateonly in such a channel.

Reading buoys and other markers

The waters of the United States aremarked for safe navigation by the lateralsystem of buoyage. Simply put, buoys andmarkers have an arrangement of shapes,colors, numbers and lights to show whichside of the buoy a boater should pass onwhen navigating in a particular direction.The markings on these buoys are orientedfrom the perspective of being entered fromseaward (the boater is going towards theharbor). Red buoys are passed on your star-board (right) side when proceeding fromopen water into the harbor, and black buoysare to your port (left) side. An easy way toremember the meaning of the colors is thephrase “red right returning.” When navigat-ing out of the harbor, your position withrespect to the buoys should be reversed; redbuoys should be to port and black buoys tostarboard.

Many bodies of water used by boaters areentirely within the boundaries of a particularstate. The Uniform State Waterway MarkingSystem has been devised for these waters.

1-19

E

This system uses buoys and signs withdistinctive shapes and colors to show regu-latory or advisory information. These mark-ers are white with black letters and orangeborders. They signify speed zones,restricted areas, danger areas, and generalinformation.

Remember, markings may vary by geo-graphic location. Always consult local boat-ing authorities before riding your watercraftin unfamiliar waters.

1-20

E

EJU00320

To get more boating safety information

Be informed about boating safety. Addi-tional publications and information can beobtained from many organizations, includingthe following.

United States Coast GuardConsumer Affairs Staff (G-BC)Office of Boating, Public, and Consumer

AffairsU.S. Coast Guard HeadquartersWashington, D.C. 20593-0001Boating Safety Hotline: 1-800-368-5647

Other sourcesYou can find local rules by contacting the

National Association of State Boating LawAdministrators, or your local Power Squad-ron.

Watercraft Education and Training

The Online Boating Safety Course, avail-able through the watercraft section of theyamaha-motor.com website, is a free,50 question learning course available to thepublic. Upon successful completion of80 percent or better, the user can request acertificate of completion by mail or candownload one immediately. The OnlineBoating Safety Course, provided by theBoat/US Foundation, is approved by theNational Association of State Boating LawAdministrators (NASBLA) and recognizedby the United States Coast Guard. Thiscourse meets the education requirement forthose states that recognize non-proctored,NASBLA-approved courses.

Yamaha is the watercraft industry’s lead-ing manufacturer to build awareness andsupport for boating education. In 1997,Yamaha launched its GET W.E.T. (Water-craft Education and Training) initiative andhas since reached out to over one millionAmericans promoting the benefits of boatingeducation.

The Online Boating Safety Course:http://www.boatus.com/onlinecourse/

1-21

E

EJU00322

Enjoy your watercraft responsibly

You share the areas you enjoy whenriding your watercraft with others and withnature. So your enjoyment includes aresponsibility to treat these other people,and the lands, waters, and wildlife withrespect and courtesy.

Whenever and wherever you ride, think ofyourself as the guest of those around you.Remember, for example, that the sound ofyour watercraft may be music to you, but itcould be just noise to others. And the excit-ing splash of your wake can make wavesothers won’t enjoy. Avoid riding close toshoreline homes and waterfowl nestingareas or other wildlife areas, and keep arespectful distance from fishermen, otherboats, swimmers, and populated beaches.When travel in areas like these is unavoid-able, ride slowly and obey all laws.

Remember that pollution can be harmfulto the environment. Do not refuel or add oilwhere a spill could cause damage to nature.Remove your watercraft from the water andmove it away from the shoreline before refu-eling. And keep your surroundings pleasantfor the people and wildlife that share thewaterways: don’t litter!

When you ride responsibly, with respectand courtesy for others, you help ensurethat our waterways stay open for the enjoy-ment of a variety of recreational opportuni-ties.

E

2

EJU00326

FEATURES AND FUNCTIONS

Location of main components ...............2-1

Operation of controls and other functions....................................................2-5

Rear seat.................................................2-5Front seat ................................................2-6Hood........................................................2-7Fuel tank filler cap...................................2-8Oil tank filler cap......................................2-8Fuel cock knob........................................2-9Engine stop switch................................2-10Engine shut-off switch...........................2-10Choke knob...........................................2-10Throttle lever .........................................2-11Start switch............................................2-11Cooling water pilot outlet ......................2-12Steering system....................................2-12Tilt lever.................................................2-13Shift lever ..............................................2-14Quick Shift Trim System (QSTS) selector..................................................2-15Engine overheat warning system.........2-17Exhaust temperature warning system...................................................2-19Handgrip................................................2-20Multifunction meter................................2-21PADLOC (Programmable digital locking ignition)..................................................2-22Tachometer...........................................2-24Speedometer ........................................2-25Fuel meter.............................................2-25Engine oil meter....................................2-26Clock .....................................................2-26Hour meter ............................................2-27Trip timer ...............................................2-27Tripmeter...............................................2-28Fuel warning indicator...........................2-28Oil warning indicator .............................2-29Engine overheat warning indicator.......2-29Exhaust temperature warning indicator.................................................2-30Battery warning indicator......................2-30Storage compartments .........................2-31

2-1

E

EJU00327

Location of main components

1 HandlebarsUse to control direction.

2 FootwellUse to place feet for balance.

3 FootrestUse to place feet for proper balance whenseated facing rearward and acting as a spotterfor a water-skier.

4 Bow eyeUse to attach rope for transporting, mooring ortowing the watercraft in an emergency.

5 Hood6 Front seat7 Rear seat8 Sponsons9 Gunwale

2-2

E

1 Fuel tank filler cap2 Rope holes3 Intake grate

Prevents debris from getting into the jet pump.4 Speed sensor5 Cleat

Use to attach a towrope for pulling water-skier,or a rope for mooring the watercraft.

6 HandgripUse for support when boarding the watercraftor when seated facing rearward and acting asa spotter for a water-skier.

7 Reverse gateControls direction of jet thrust when in reverse.

8 Stern drain plugsUse to drain water in the bilge when the water-craft is on dry land.

9 Jet thrust nozzleChanges the direction of jet thrust accordingto handlebar position.

0 Ride plate

2-3

E

1 Engine stop switchPush to stop the engine normally.

2 ClipInsert into the engine shut-off switch to enablestarting of the engine.Remove to stop the engine or prevent acci-dental starting of the engine or unauthorizeduse of the watercraft.

3 Quick Shift Trim System (QSTS) selectorUse to select the trim angle of the watercraft.

4 QSTS shift lock lever5 Engine shut-off switch

Remove the clip to stop the engine and dis-able it from starting.

6 Start switchPush to start the engine.

7 Fuel cock knobUse to select either normal or reserve fuel flowfrom the fuel tank to the carburetors, or to shutoff fuel flow.

8 Choke knobUse to start a cold engine.

9 Engine shut-off cord (lanyard)Attach to wrist so that the engine stops if theoperator falls off the watercraft.

0 Adjustable rearview mirrorsA Multifunction meter

Use to check watercraft operation.B Shift lever

Use to put the watercraft into forward orreverse.

C Throttle leverUse to accelerate and decelerate.

D Tilt leverUse to adjust the tilt of the handlebars.

E Glove compartment

2-4

E

1 Spark plugs/Spark plug caps2 Electrical box

Protects electrical components from water.3 Flush hose connector

Use to flush the engine cooling water pas-sages.

4 Spark plug lead5 Muffler6 Fuel filter7 Fuel tank

8 Oil tank9 Battery

2-5

E

EJU00328

Operation of controls and other functions

EJU00335a

Rear seatTo remove the rear seat:

Pull the rear seat latch 1 up, and thenpull the seat off.

To install the rear seat:Insert the projections on the front of the

seat into the stays on the deck, and thenpush the rear of the seat down to lock it inplace securely.

2-6

E

EJU00714

Front seatTo remove the front seat:1. Remove the rear seat.2. Pull the front seat latch 2 up, and then

pull the seat off.

To install the front seat:1. Insert the projections on the front of the

seat into the stays on the deck, and thenpush the rear of the seat down to lock itin place.

2. Install the rear seat.NOTE:Make sure that the seats are properlysecured before operating the watercraft.

2-7

E

EJU00703

HoodTo open the hood, pull the latch 1 up,

and then lift the hood up.To close the hood, push the hood down to

lock it in place.NOTE:Make sure that the hood is properly securedbefore operating the watercraft.

2-8

E

EJU00347

Fuel tank filler capTo remove the fuel tank filler cap 1, turn it

counterclockwise.NOTE:Make sure that the fuel tank filler cap isproperly secured before operating the water-craft.

EJU00001N

Oil tank filler capTo remove the oil tank filler cap:1. Open the hood. (See page 2-7 for hood.)2. Turn the filler cap 2 counterclockwise.

To install the oil tank filler cap:Install the filler cap, and then close the

hood.NOTE:Make sure that the oil tank filler cap andhood are properly secured before operatingthe watercraft.

2-9

E

EJU00704

Fuel cock knobThe fuel cock supplies fuel from the fuel

tank to the carburetors.The fuel cock knob 1 positions are

explained as follows and are shown in theillustration.OFF:

With the fuel cock knob in this position,fuel does not flow. Always turn the fuel cockknob to this position when the engine is notrunning.ON:

With the fuel cock knob in this position,fuel flows to the carburetors. Turn the fuelcock knob to this position when starting theengine and operating the watercraft.RES:

This indicates reserve. With the fuel cockknob in this position, the fuel reserve ismade available. Turn the fuel cock knob tothis position if you run out of fuel while oper-ating the watercraft. When this occurs,refuel as soon as possible and be sure toturn the fuel cock knob back to “ON”!

2-10

E

EJU00705

Engine stop switchPush this switch 1 (red button) to stop

the engine normally.

EJU00706

Engine shut-off switchInsert the clip 1, on the end of the engine

shut-off cord 2, under the engine shut-offswitch 3 (black button). The engine will stopautomatically when the clip is removed fromthe switch, such as if the operator falls offthe watercraft.

WARNING● Always attach the engine shut-off cord

to your wrist and the clip to the engineshut-off switch BEFORE starting theengine.

● To prevent accidental starting of theengine or unauthorized use by chil-dren or others, always remove the clipfrom the shut-off switch when theengine is not running.

EJU00350

Choke knobStarting a cold engine requires a richer

air-fuel mixture, which is supplied by thechoke.

Pull the knob 1 out to turn the choke on.Push the knob in to turn the choke off.

2-11

E

EJU00351

Throttle leverSqueeze the throttle lever 1 to increase

engine speed. Release the throttle lever to decrease

engine speed or to return it to the idle posi-tion.

EJU00353

Start switchPush the start switch 1 (green button) to

start the engine.NOTE:● The engine will not start when the clip is

removed from the engine shut-off switch.● The engine will not start if the “LOCK” mode

of the multifunction meter has been selected.(See page 2-22 for “PADLOC” mode selec-tion procedures.)

2-12

E

EJU00354

Cooling water pilot outletThis watercraft is equipped with cooling

water pilot outlets.When the engine is running, cooling

water is circulated in the engine, and then itis discharged from the pilot outlets.

To check for proper operation of the cool-ing system, check that water is being dis-charged from the pilot outlets. If water is notbeing discharged from the outlets, coolingwater may not be circulating in the engine.When this occurs, stop the engine and checkfor the cause. (See pages 2-17 and 5-4 forfurther instructions.)NOTE:If the cooling water passages are dry, it willtake about 20 seconds for the water to reachthe outlets after the engine is started.

EJU00356

Steering systemYour watercraft can be steered by turning

the handlebars 1 the same direction youwish to travel.

When the handlebars are turned, theangle of the jet thrust nozzle 2 is changed,and the direction of the watercraft ischanged accordingly. Since the strength ofthe jet thrust determines the speed anddirection of a turn, the throttle must alwaysbe open when attempting a turn, except attrolling speed.

2-13

E

EJU00670

Tilt leverThe tilt lever 1 is located in front of the

glove compartment and is used to adjust thetilt of the handlebars.

To adjust the tilt, pull the tilt lever up, andthen move the handlebars up or down to thedesired position.

WARNING● Never touch the tilt lever during opera-

tion, otherwise the handlebars maysuddenly change position, which maylead to an accident.

● Be sure to fasten the tilt lever properlyafter adjusting the handlebar position.If the handlebars are not properly fas-tened, they may suddenly changeposition, which may lead to an acci-dent.

2-14

E

EJU00710

Shift leverThe shift lever is located on the starboard

side of the watercraft and is used to controlthe reverse gate, which allows the watercraftto move into reverse or forward.

When in the reverse position, the water-craft can be launched from a trailer, orbacked up out of tight spots where you can-not turn around easily.To shift into reverse:1. Release the throttle, and then let the

engine speed return to idle.2. Pull the shift lever toward you.

WARNING● Make sure that the throttle is com-

pletely released and that the engine isat idle before shifting into reverse.

● Do not use the reverse function toslow down or stop the watercraft as itcould cause you to lose control, beejected, or impact the handlebars.

● Use reverse for slow-speed maneuver-ing only.

● Make sure that there are no obstaclesor people behind you before shiftinginto reverse.

● Do not touch the reverse gate while theshift lever is being operated, otherwiseyou could be pinched.

To shift into forward:1. Release the throttle, and then let the

engine speed return to idle.2. Push the shift lever away from you.

2-15

E

EJU00360a

Quick Shift Trim System (QSTS) selector

The QSTS selector 1 is located at theleft handlebar grip and is used to adjust thetrim angle of the watercraft.

Operating the QSTS selector changes theangle of the jet thrust nozzle vertically. Thischanges the trim angle of the watercraft.

There are 5 positions: 2 bow down posi-tions A and B, neutral “N,” and 2 bow uppositions C and D.To change the trim angle:1. Reduce engine speed to 3,000 r/min or

less.2. Squeeze the shift lock lever 2, and then

turn the QSTS selector to the desiredposition.

3. Release the shift lock lever to lock theQSTS selector.

CAUTION:Do not turn the QSTS selector whileoperating the watercraft at full throttle,otherwise damage could occur to theQSTS.

The neutral “N” position will provide goodperformance for most operating conditions.

To enhance particular types of perfor-mance, select bow down or bow up.

2-16

E

Bow downTurn the grip to A or B and the bow will

go down while the watercraft is on plane.Bow down puts more of the bow in the

water. This gives the watercraft more “hook,”which enhances turning performance. Thisposition will also help the watercraft get upon plane more quickly.

At higher speeds, however, the watercraftwill have greater tendency to “bow steer”and follow waves and wakes in the water.Fuel economy and maximum speed are alsoreduced.

Bow upTurn the grip to C or D and the bow will

go up while the watercraft is on plane. Bow up puts less of the bow in the water.

There is less water resistance, so straight-ahead acceleration when on plane and topspeed are enhanced.

In some conditions, however, the water-craft may tend to “porpoise” (hop in thewater). If the watercraft is porpoising,choose neutral or bow down.

2-17

E

EJU00366

Engine overheat warning system

The model has an overheat warningdevice. If the engine starts to overheat, thewarning light, indicator and “W.TEMP” onthe meter begin to blink and the buzzersounds intermittently. If this happens,reduce the engine speed and return tobeach at low speed. If there is no water dis-charge at the cooling water pilot outlet whilethe engine is running, check the jet intakeand impeller for clogging.

WARNINGBefore attempting to remove weeds ordebris from the intake grate or impeller,shut the engine off and remove the clipfrom the engine shut-off switch. Severeinjury or death could result from comingin contact with the rotating parts of thejet pump.

CAUTION:This model is equipped with a catalyticconverter.● Return to shore at low speed if the

overheat warning indicator and buzzerare on, and the display shows“W.TEMP.” If you ignore these signals,the engine will stop running and can-not be restarted until the exhaust sys-tem cools.

● Have your watercraft inspected andserviced by a Yamaha dealer if theengine stopped due to overheating.

2-18

E

If the initial overheat warning is ignored,engine and exhaust system heat canincrease, particularly if the watercraft contin-ues to be operated at higher speed. If so,the warning indicators and buzzer willchange from intermittent to constantly onand the overheat system will stop ignition tothe engine to reduce the risk of severe over-heating. The engine cannot be restarteduntil it cools down, so it may be necessary tohave the watercraft towed back to thebeach. Refer to “Towing the watercraft” onpage 5-7.NOTE:● The buzzer stops sounding if any button

on the meter is pressed. ● Ask a Yamaha dealer to inspect the

watercraft if there is no apparent reasonfor overheating.

2-19

E

EJU00697a

Exhaust temperature warning system

This model has an exhaust temperaturewarning device. If the exhaust temperaturegets too hot, the warning light, indicator and“EXHST” will blink. The buzzer also soundsintermittently. If this happens, reduce enginespeed and return to the beach at low speed.Allow the exhaust system to cool.

WARNINGHot muffler surfaces can cause seriousburns. Do not touch any muffler surfaceduring or after engine operation. The cat-alytic converter gets hotter after theengine stops.

CAUTION:This model is equipped with a catalyticconverter. Return to shore at low speed(below 4,000 r/min) if the warning indica-tor and buzzer are on, and the displayshows “EXHST.” Have your watercraftinspected and serviced by a Yamahadealer if the engine stopped due to over-heating.

NOTE:● The buzzer stops sounding if any button

on the meter is pressed.● Ask a Yamaha dealer to inspect the

watercraft if there is no apparent reasonfor overheating.

2-20

E

EJU00367a

HandgripThe handgrip 1 provides a handhold for

boarding the watercraft and for a spotterwhen facing rearward.

CAUTION:Do not use to tow objects, lift watercraft,or attach tie downs, otherwise damagecould occur.

2-21

E

EJU00698b

Multifunction meterThis meter contains following functions for

help and convenience in operating thewatercraft.1 “MODE” button2 “SET” button3 “CODE” setting buttons4 Tachometer5 Speedometer6 Fuel meter7 Engine oil meter8 Display for Clock, Hour meter, Trip meter and

Trip timer9 Warning light0 Display for PADLOC and direction of warning

indicatorA Battery warning indicatorB Exhaust temperature warning indicatorC Engine overheat warning indicatorD Fuel warning indicatorE Oil warning indicator

CAUTION:● Do not run the engine over 4,000 r/min

to check the meter for operation onland. The engine could overheat or thecatalytic converter could result in seri-ous damage.

● Use the specified resistor-type sparkplugs and caps, otherwise the metermay function erratically.

NOTE:The demonstration mode display startsshowing after the engine starts. Then all dis-plays light up and the buzzer sounds twice.The meter will operate normally after a fewseconds. The current display will continue tooperate for 30 seconds after the enginestops.

2-22

E

EJU00711a

PADLOC (Programmable digital locking ignition)

This feature is provided to deter unautho-rized use.

The function allows you to choose either“START” or “LOCK” mode, as the situationrequires, much as you would use an ignitionkey in a motor vehicle. If you have previouslychosen “LOCK” mode, the engine will notstart unless the right code is put in to select“START” mode.NOTE:If you do not use the PADLOC system, it isunnecessary to perform the initial setting ofthe PADLOC. In this case, the “START”mode is automatically selected.

PADLOC initial setting1. Disconnect the blue connector 1 behind

the front storage compartment.

2. After the warning light turns on, pressthe “MODE” button for at least 3 secondsuntil the display shows “COdE.” You areready to set your code.

2-23

E

3. Select your four-letter code by pressingthe “A/SET,” “B,” or “C” buttons in adesired sequence.

NOTE:If you do not press a button for more than10 seconds, the display automatically turnsoff. This cancels the process of setting acode.

4. After code setting is complete, thebuzzer will sound 3 times and the displaywill show “SET.” Lastly, the display turnsoff and the warning light turns on again.After the meter has displayed thissequence, connect the blue connectoragain.

NOTE:● Your own code is kept even if the battery

terminal is disconnected.● If you forget your own code, or if you want

to change the code, do this initial settingprocedure again from the beginning.

Selecting “PADLOC” modeSelecting the desired mode can only be

done after the initial setting has been doneand while the display is not lit.1. Press the “MODE” button until the meter

displays the current mode, “START” or“LOCK.”

2. With “START” or “LOCK” displayed,press the “MODE” button continuouslyfor about 3 seconds until the displaychanges to “COdE.”

2-24

E

3. Enter your four-letter code by pressingthe “A/SET,” “B,” or “C” buttons in theright sequence.

NOTE:If you do not press a button for more than10 seconds, the display automatically turnsoff. This cancels the process of selecting themode.

4. If the code entered is correct, the modewill change from the previous mode toeither “START” or “LOCK.” Then themode display and buzzer will operate for2 seconds.

NOTE:● Once you select a mode, the mode will

not change unless you perform this modeselection sequence again.

● If the wrong code is entered, the modedisplay shows “ERROR” for 2 secondsand the buzzer will sound 5 times. Thenthe display returns to “COdE.”

EJU00383

TachometerThe engine speed (r/min) is displayed by

segments. Each segment indicates a 200 r/minincrement.

2-25

E

EJU00384

SpeedometerThis meter shows the watercraft speed in

miles per hour (mph).

EJU00386a

Fuel meterThe fuel meter is provided for convenient

fuel level checking while operating thewatercraft.

The fuel meter has 4 segments whichshow the amount of fuel remaining in thefuel tank.NOTE:The indication of the segments differsdepending on your operating condition. Usethe meter as a reference.

2-26

E

EJU00387a

Engine oil meterThe engine oil meter is provided for con-

venient oil level checking while operating thewatercraft.

The engine oil meter has 3 segmentswhich show the amount of oil remaining inthe oil tank.NOTE:The indication of the segments differsdepending on your operating condition. Usethe meter as a reference.

EJU00388aa

ClockA 12-hour clock is provided in this meter.To show the clock, press the “MODE” but-

ton until the display shows “CLOCK” whilethe engine is running.1. When the display shows “CLOCK,” press

the mode button for at least 3 seconds.2. The buzzer will sound once. The hour

display and “SET” start blinking. Thenpress the “A/SET” button until thedesired hour is displayed.

3. Press the “MODE” button again.4. The buzzer will sound once. The minute

display and “SET” start blinking. Thenpress the “A/SET” button until thedesired minute is displayed.

5. Press the “MODE” button again.

2-27

E

6. The buzzer will sound twice. The warn-ing light and “SET” blink for 2 seconds.Then the display turns to “CLOCK” andshows the time.

NOTE:If the battery terminal is disconnected, theclock will be reset to 12:00.

EJU00390

Hour meterThe hour meter is provided to make it

easy to follow the maintenance schedule.The meter shows how many hours of

engine operation have elapsed since thewatercraft was new.

To show the hour meter, press the“MODE” button until the display shows“HOUR.M” while the engine is running.

EJU00659a

Trip timerThe trip timer is provided for counting the

time traveled on a given trip. To show the trip timer, press the “MODE”

button until the display shows “TRIP.T” whilethe engine is running.1 Minutes2 Seconds

1. When the display shows “TRIP.T,” pressthe “A/SET” button to start counting. Thebuzzer will sound once.

2. Press the “A/SET” button again to stopcounting. The buzzer will sound once.

3. Press “MODE” button for at least2 seconds to set the time back to 00:00.The buzzer will sound twice. The timedisplay and “TRIP.T” blink for 2 seconds.Now it is ready to start counting.

2-28

E

EJU00712

TripmeterA tripmeter is provided for measuring the

approximate distance traveled. To show the tripmeter, press the “MODE”

button until the display shows “TRIP” whilethe engine is running. After showing “TRIP,”the display turns to “.MILE.”1. When the display shows “.MILE,” press

the “MODE” button for at least2 seconds.

2. The buzzer will sound twice. The warn-ing light and “.MILE” blink for 2 seconds,and “000” is displayed. Now the meterwill start to measure the distance youtravel.

3. When the tripmeter begins measuringthe distance traveled, the “.” to the left of“MILE” on the display will blink.

NOTE:Measured distance may vary depending onthe water surface conditions, and wind direc-tion. The measured distance should be usedfor a reference.

EJU00716

Fuel warning indicatorIf the fuel remaining in the tank drops to

about 17 L (4.5 US gal, 3.7 Imp gal), thelowest fuel level segment, the fuel warningindicator, “FUEL” and the warning lightbegin to blink. The buzzer also starts sound-ing intermittently.

2-29

E

EJU00717a

Oil warning indicatorIf the oil remaining in the tank drops to

about 1.4 L (0.37 US gal, 0.31 Imp gal) orthe oil filter is clogged, the lowest oil levelsegment, the oil warning indicator, “OIL” andthe warning light begin to blink. The buzzeralso starts sounding intermittently.

If the oil warning indicator begins to blink,refill with engine oil as soon as possible.NOTE:If the warning indicator blinks with adequateoil in the tank, check the oil filter for clog-ging.

EJU00718a

Engine overheat warning indicator

If the engine starts to overheat, the engineoverheat warning indicator, “W.TEMP” andthe warning light begin to blink. The buzzeralso starts sounding intermittently.

If the engine continues to be operated athigher speed after the warning system indi-cators have come on intermittently, the warn-ing indicator, “W.TEMP” and the warninglight will change to being on continuously.Also, the engine will stop and the buzzer willsound continuously. Refer to “Engine over-heat warning system” on page 2-17.NOTE:When the warnings overlap each other, theirpriority is as follows.1. Final overheat2. Exhaust temperature 3. Initial overheat4. Oil5. Fuel6. Battery

2-30

E

EJU00720a

Exhaust temperature warning indicator

If the exhaust system becomes too hot,the exhaust temperature warning indicator,“EXHST” and warning light will blink. Also,the buzzer will start sounding intermittently.Refer to “Exhaust temperature warning sys-tem” on page 2-19.

EJU00719

Battery warning indicatorIf the battery voltage becomes less than

11.5 volts, the battery warning indicator,“VOLT” and the warning light begin to blink.The buzzer also starts sounding.

If this happens during operation, beachthe watercraft. Then recharge the batteryand have the charging system inspected bya Yamaha dealer.

2-31

E

EJU00672a

Storage compartmentsA front storage compartment, a glove

compartment, and seat storage compart-ments are provided.NOTE:● Make sure that the storage compartments

are properly secured before operating thewatercraft.

● The storage compartments are notdesigned to be waterproof. If you carryobjects that must be kept dry, such as themanuals, put them in a waterproof bag.

Front storage compartmentThe front storage compartment 2 is

located at the bow.To open the front storage compartment,

pull the hood latch 1 up, and then open thehood.

To close the front storage compartment,push down on the rear of the hood until itlatches securely.NOTE:The front storage compartment can beremoved to access the engine room.

Front storage compartment:Capacity: 56 L (15 US gal, 12 Imp gal)Load limit: 5 kg (11 lb)

2-32

E

Glove compartmentA glove compartment 4 is located in front

of the seat. To open the glove compartment, slide the

latch 3 toward you, and then lift up the lid.To close the glove compartment, push the

lid down until it locks securely.

Glove compartment:Capacity: 1.7 L (0.45 US gal, 0.37 Imp gal)Load limit: 1 kg (2.2 lb)

Seat storage compartmentThe seat storage compartment 5 is

located under the rear seat.To open the seat storage compartment,

remove the rear seat. (See page 2-5 for rearseat.)

Rear storage compartments:Capacity: 30 L (8 US gal, 6.6 Imp gal)Load limit: 9 kg (19.8 lb)

E

–MEMO–

E

3

EJU00410

OPERATION

Fuel and oil................................................3-1Gasoline ..................................................3-1Filling the fuel tank..................................3-32-stroke engine oil...................................3-3Filling the oil tank ....................................3-4

Pre-operation checks...............................3-5Pre-operation check list ..........................3-5Pre-operation check points.....................3-6

Operation.................................................3-14Engine break-in.....................................3-14Launching the watercraft ......................3-16Starting the engine................................3-16Stopping the engine..............................3-19Leaving the watercraft ..........................3-19

Operating your watercraft.....................3-20Getting to know your watercraft............3-20Learning to operate your watercraft .....3-20Riding watercraft with passengers .......3-21Starting the watercraft...........................3-22Boarding and starting in deep water ....3-24Capsized watercraft..............................3-26Turning the watercraft...........................3-28Stopping the watercraft.........................3-30Beaching the watercraft........................3-31Docking the watercraft..........................3-31Reverse on waterways .........................3-32Rough water operation .........................3-32

Post-operation checks ..........................3-33

Transporting ...........................................3-35

3-1

E

EJU00411a

Fuel and oilThis engine uses Yamaha’s oil injection

system, which provides superior lubricationby ensuring the proper oil ratio for all operat-ing conditions. No fuel premixing is neces-sary except during the engine break-inperiod. Simply pour gasoline into the fueltank and oil into the oil tank.

Gasoline

WARNINGGASOLINE AND ITS VAPORS AREHIGHLY FLAMMABLE AND EXPLOSIVE!● Do not smoke when refueling, and

keep away from sparks, flames, orother sources of ignition.

● Stop engine before refueling.● Refuel in a well-ventilated area. Do not

stand or sit on the watercraft whilerefueling in case of fire.

● Take care not to spill gasoline. If gaso-line spills, wipe it up immediately withdry rags. Always properly dispose ofgasoline-soaked rags.

● Avoid overfilling the fuel tank. Stop fill-ing when the fuel level just reaches thebottom of the filler tube. Do not fill upthe filler tube because fuel expands asit warms up and could overflow.

● Tighten the filler cap securely afterrefueling.

● If you should swallow some gasoline,inhale a lot of gasoline vapor, or getgasoline in your eyes, get immediatemedical attention.

● If any gasoline spills onto your skin,immediately wash with soap andwater. Change clothing if gasolinespills on it.

3-2

E

CAUTION:● Do not use leaded gasoline. Leaded

gasoline can seriously damage thecatalytic converter.

● Use only fresh gasoline that has beenstored in clean containers.

GasoholThere are two types of gasohol: gasohol

containing ethanol and that containing meth-anol.

Gasohol containing ethanol can be usedif ethanol content does not exceed 10 % andthe fuel meets minimum octane ratings.

Gasohol containing methanol is not rec-ommended by Yamaha because it cancause fuel system damage or engine perfor-mance problems.

Recommended gasoline:Regular unleaded gasoline witha minimum octane rating of86 (Pump octane number) = (R+M)/290 (Research octane number)

3-3

E

EJU00724a

Filling the fuel tankCAUTION:

Be careful when refueling. Avoid gettingwater or other contaminants in the fueltank. Contaminated fuel can cause poorrunning or engine damage.

1. Open the hood and remove the frontstorage compartment, to check the fuellevel. (See page 2-31 for front storagecompartment.)

2. Open the fuel tank filler cap, and slowlyadd fuel to the fuel tank.

3. Stop filling when the fuel just reaches thetop of the fuel tank visible under theengine oil tank.

EJU00324a

2-stroke engine oilCAUTION:

Use only YAMALUBE 2-W oil. Usinganother oil can seriously damage the cat-alytic converter and other engine compo-nents.

NOTE:YAMALUBE 2-W is developed for this water-craft and available from a Yamaha dealer.

Fuel tank capacity:Total: 70 L (18.5 US gal, 15.5 Imp gal)Reserve: 12 L (3.2 US gal, 2.7 Imp gal)

Recommended engine oil:YAMALUBE 2-W oil only

3-4

E

EJU00419a

Filling the oil tank

WARNING● Do not add gasoline to the oil tank.

Fire or explosion could result.● Oil in the bilge is a serious fire hazard.

Wipe up any spilled oil immediately.

CAUTION:Do not allow the oil tank to become com-pletely empty. If the oil tank becomesempty the oil injection pump must bebled to ensure proper oil flow, otherwiseengine damage may occur. If bleeding ofthe oil pump is necessary, have aYamaha dealer bleed it.

1. Open the hood to access the oil tankfiller cap. Also, remove all seats to watchthe oil level. (See page 2-7 for hood, and2-5 and 2-6 for rear and front seat.)

2. Open the oil tank filler cap, and veryslowly add engine oil to the oil tank.

3. Stop pouring when the oil just reachesthe bottom of the filler tube.

Oil tank capacity:5.5 L (1.5 US gal, 1.3 Imp gal)

3-5

E

EJU00422

Pre-operation checksPre-operation check list

Before operating this watercraft, perform the checks in the following check list. See theaccompanying text in this chapter for details on how to perform the checks.

WARNINGIf any item in the pre-operation check list is not working properly, have it inspectedand repaired before operating the watercraft, otherwise an accident could occur.

NOTE:Pre-operation checks should be made thoroughly each time the watercraft is used. This pro-cedure can be completed in a short time. It is worth the time spent to assure safety and reli-ability.

ITEM ROUTINE PAGE

Engine compartment Remove all seats and front storage compart-ment to ventilate engine compartment. Check for fuel vapors or loose electrical connections

3-6

Bilge Check for water and fuel residue and remove if necessary

3-7

Throttle Check that the throttle lever springs back 3-10

Steering system Check for proper steering system operation 3-10

Shift lever and reverse gate Check for proper operation 3-11

Fuel and oil Check fuel and oil level and add if necessaryCheck hoses and tanks for leakage

3-6

Water separator Check for water and drain if necessary 3-7

Battery Check electrolyte level and battery condition 3-8

Front and rear seats Check that the seats are properly secured 2-5, 2-6

Hull/Deck Check the hull and deck for cracks or other dam-age

—

Jet unit Check for debris and remove if necessary 3-12

Fire extinguisher Check the condition and replace if necessary 3-9

Engine shut-off cord Check condition and replace if frayed or broken 3-12

Switches Check the start switch, engine stop switch and engine shut-off switch for proper operation when the watercraft is in the water

3-13

Cooling water pilot outlet Check that water is discharged while the engine is running when the watercraft is in the water

3-13

Multifunction meter Check for warning indications and proper opera-tion

3-13

3-6

E

EJU00426

Pre-operation check pointsEngine compartment

Ventilate the engine compartment beforeeach use.

To ventilate the engine compartment,remove all seats and front storage compart-ment. (See pages 2-5 and 2-6 for front andrear seat, and 2-31 for front storage com-partment.) Allow the engine compartment toremain open for a few minutes to allow anyfuel vapors to escape. Also, check for looseelectrical connections.

WARNINGFailure to ventilate the engine compart-ment could result in fire or explosion. Donot start the engine if there is a fuel leakor a loose electrical connection.

EJU00427-30a

Fuel and oil systemsCheck the fuel system for leakage, cracks

or malfunctions before each use. (See page4-9 for check points and correct proce-dures.)1. Remove the fuel tank filler cap to release

any pressure that might have built up inthe fuel tank.

2. Remove all seats and front storage com-partment. (See pages 2-5 and 2-6 forfront and rear seat, and 2-31 for frontstorage compartment.)

3. Check the fuel and oil levels in the tanksand replenish if necessary. (See pages 3-3and 3-4 for filling instructions.)

3-7

E

EJU00432a

Water separatorCheck the water separator 1 for water.

Normally the water separator is empty. Thewater separator retains any water enteringthrough the fuel tank breather hose if thewatercraft is capsized.

If water remains in the water separator,drain it by removing the drain screw 2.Install the drain screw again after drainingthe water separator.

EJU00433a

BilgeCheck for moisture and fuel residue in the

bilge.Excessive water in the bilge can splash

into the carburetor and engine which couldcause engine damage. To remove water from the bilge:1. Remove the stern drain plugs.2. Raise the bow of the watercraft until the

water drains.3. After the water has drained, wipe the

bilge with dry rags to make sure that thebilge is thoroughly dry.

4. Install the drain plugs.

CAUTION:● Make sure that the stern drain plugs

are tightened securely before launch-ing the watercraft.

● Clean any foreign materials, such asdirt or sand, from the drain plugthreads before installing the drainplugs.

3-8

E

EJU00435a

BatteryCheck the battery condition and the elec-

trolyte level. Check that the battery leads are tightened

securely and there is no corrosion on thebattery terminals.

WARNINGThe battery must always be fully chargedand in good condition. Loss of batterypower may leave you stranded. Neveroperate the watercraft if the battery doesnot have sufficient power to start theengine or if it shows any other signs ofdecreased power.

Make sure that the breather hose is prop-erly connected and that it is not damaged orobstructed.

Make sure that the battery is securelyheld in place.1 Positive (+): Red lead2 Negative (–): Black lead3 Breather hose

3-9

E

F0P03010

EJU00728

Fire extinguisherCheck that there is a full fire extinguisher

on board. The fire extinguisher container 1is located in the front storage compartment.

To open the fire extinguisher containercap 2 turn it counterclockwise.

After inserting the fire extinguisher makesure that the container cap is tightenedsecurely.NOTE:● See the instructions supplied by the fire

extinguisher manufacturer for checkingthe fire extinguisher. Always keep theextinguisher in the fire extinguisher con-tainer.

● Always carry a fire extinguisher on board.A fire extinguisher is not standard equip-ment with this watercraft. If you do nothave one, contact a Yamaha dealer or afire extinguisher dealer to obtain onemeeting the proper specifications.

Fire extinguisher:Classification: B-1Capacity: 2 lb or more

3-10

E

EJU00447

ThrottleSqueeze and release the throttle lever

several times to make sure that there is nohesitation in its travel. It should be smoothover the complete range, and spring back tothe idle position when released.

WARNINGBefore starting the engine, always checkthe operation of the throttle lever. Itshould move smoothly through its fullrange of operation, and should springback to the idle position when released.

EJU00448

Steering systemCheck for looseness in the handlebars.Turn them as far as possible to the right

and left to make sure that operation issmooth and unrestricted throughout thewhole range. Make sure that the jet thrustnozzle also changes directions as the han-dlebars are turned, and that there is no freeplay between the handlebars and the jetthrust nozzle.

Check that the tilt lever is locked in posi-tion. (See Tilt lever on page 2-13.)

3-11

E

EJU00450

Shift lever and reverse gateCheck for proper operation of the shift

lever and reverse gate.Make sure that the reverse gate goes

down to its stopper position when the shiftlever is pulled up.

Also, make sure that the reverse gategoes up to its stopper position when shiftlever is pushed down.

WARNINGJJ

● Make sure that the throttle is com-pletely released and that the engine isat idle before shifting into reverse.

● Do not use the reverse function toslow down or stop the watercraft as itcould cause you to lose control, beejected, or impact the handlebars.

● Use reverse for slow-speed maneuver-ing only.

● Make sure that there are no obstaclesor people behind you before shiftinginto reverse.

● Do not touch the reverse gate while theshift lever is being operated, otherwiseyou could be pinched.

3-12

E

EJU00451a

Jet unitCarefully check the jet intake for weeds,

debris, or anything else that might restrictthe intake of water. If the intake is clogged,cavitation could occur, reducing jet thrust,and possibly damaging the jet pump.

In some cases, the engine may overheatbecause of lack of cooling water, and dam-age to the engine could result. Engine cool-ing water is fed to the engine by the jetpump. (See page 5-4 for jet intake cleaningprocedures.)

WARNING● Keep away from intake grate while

engine is on. Items such as long hair,loose clothing, or PFD straps canbecome entangled in moving partsresulting in severe injury or drowning.

● Stop the engine and remove the clipfrom the engine shut-off switch beforeremoving any debris or weeds, whichmay have collected around the jetintake.

EJU00004n

Engine shut-off cord (lanyard)Check that the engine shut-off cord is not

frayed or broken. If the cord is damaged,replace it; never try to repair it or tie ittogether.

3-13

E

EJU00452a

SwitchesCheck the start switch 1, the engine stop

switch 2, and the engine shut-off switch 3for proper operation.

To check these switches place the water-craft in the water to provide adequate cooling.Start the engine, and then pull the engineshut-off cord 5 to remove the clip 4 from theengine shut-off switch. Verify that the enginestops immediately. (See pages 3-16 to 3-19for information on proper operation of thestart switch, the engine stop switch and theengine shut-off switch.)

EJU00453

Cooling water pilot outletCheck that water comes out from the out-

let while the engine is running and thewatercraft is in the water.

EJU00454

Multifunction meterCheck the operation of the multifunction

meter. (See pages 2-21 to 2-30 for operationof the meter.)

3-14

E

EJU00676a

Operation

WARNINGBefore operating your watercraft,become familiar with all controls. Con-sult your Yamaha dealer about any con-trol or function you do not fullyunderstand. Failure to understand howcontrols work could cause an accident orprevent you from avoiding an accident.

CAUTION:Make sure that stern drain plugs aresecurely tightened before launching thewatercraft.

EJU00459

Engine break-inThe engine break-in period is essential to

allow the various components of the engineto wear and polish themselves to the correctoperating clearances. This ensures properperformance and promotes longer compo-nent life.

CAUTION:For the first tankful of operation, premixa 50:1 mixture of fuel and oil (in additionto the oil in the oil tank).After break-in, use straight gasoline fornormal operation.

1. Launch the watercraft and start theengine. (See pages 3-16 to 3-18 forengine starting procedures.)

2. Run the engine at the lowest possiblespeed for 5 minutes.

3-15

E

3. Gradually open the throttle and run theengine at 5,000 r/min or less.

4. Continue operation at 5,000 r/min or lessuntil the first tankful of fuel has beenused up.

5. Fill the tank with straight gasoline, andthen proceed with normal operation.

CAUTION:Failure to follow the engine break-in pro-cedure properly can result in severedamage to the engine.

3-16

E

EJU00506

Launching the watercraftMake sure that there are no obstructions

behind you. After the watercraft is in the water, start

the engine. Shift into reverse and move thewatercraft back slowly. If there are waves,someone should make sure that the water-craft is not pushed into the trailer beforebacking away.

EJU00645a

Starting the engine

WARNINGNever start the engine or let it run for anylength of time in an enclosed area.Exhaust fumes contain carbon monox-ide, a colorless, odorless gas that maycause loss of consciousness and deathwithin a short time. Always operate thewatercraft in an open area.

1. Launch the watercraft in water free fromweeds and debris and at least 60 cm(2 ft) deep.

WARNINGNever operate in water that is less than60 cm (2 ft) deep, otherwise you increaseyour chance of hitting a submergedobject, which could result in injury.

CAUTION:Never operate in water that is less than60 cm (2 ft) deep, otherwise pebbles orsand could be sucked into the jet intake,causing impeller damage or engine over-heating.

3-17

E

2. Turn the fuel cock knob to the “ON” posi-tion.

NOTE:Before first starting the engine, remove thefuel tank filler cap to release any built-uppressure in the tank due to fuel expansion.

3. Attach the clip 1 to the engine shut-offswitch 2. Also, attach the engine shut-off cord 3 to your left wrist.

WARNINGCheck that the engine shut-off cord is notfrayed or broken, and keep it free fromthe handlebars so the engine stops if theoperator falls off. The engine shut-offcord may not pull free if wrapped aroundthe handlebars when the operator fallsoff, allowing the watercraft to continue torun and cause an accident.

NOTE:It is not possible to start the engine with theclip removed from the engine shut-offswitch.

4. Pull and hold the choke knob all the wayout to start a cold engine.

NOTE:The choke should not be used when theengine is warm.

3-18

E

5. If the “LOCK” mode was chosen previ-ously, choose the “START” mode beforestarting the engine. (See pages 2-23 to2-24 for selecting “PADLOC” mode.)

NOTE:● If the initial setting of the PADLOC has not

been done, the “START” mode is auto-matically selected.

● If you have previously chosen “LOCK”mode, the engine will not start unless thecorrect code is entered. This selects the“START” mode.

6. While lightly squeezing the throttle lever,push the start switch (green button).

WARNINGOn this watercraft, the engine is con-nected directly to the jet pump. Startingthe engine immediately generates somethrust. Apply only enough throttle tokeep the engine running.

7. Release the start switch as soon as theengine starts to run.

CAUTION:● Never push the start switch while the

engine is running.● Do not operate the start switch for

more than 5 seconds, otherwise thebattery will be discharged and theengine will not start. Also, the startermotor may be damaged. If the enginedoes not start in 5 seconds, releasethe start switch, wait 15 seconds, andtry again.

8. After the engine has warmed up, pushthe choke knob in to its original position.

NOTE:If the choke knob is left pulled out, theengine will stall.

3-19

E

EJU00463a

Stopping the engineTo stop the engine, release the throttle

lever, and then push the engine stop switch(red button).

WARNINGYou need throttle to steer. Shutting offthe engine can cause you to hit an obsta-cle you are attempting to avoid. A colli-sion could result in severe injury ordeath.

EJU00005n

Leaving the watercraftIf leaving the watercraft, choose the

“LOCK” mode on the multifunction meter bysetting PADLOC, and remove the engineshut-off cord to reduce the chance of acci-dental starting or unauthorized use by chil-dren or others.

To set the mode, see PADLOC under Mul-tifunction meter.

3-20

E

EJU00674

Operating your watercraftGetting to know your watercraft

Operating your watercraft requires skillsacquired through practice over a period oftime. Take the time to learn the basic tech-niques well before attempting more difficultmaneuvers.

Operating your new watercraft can be avery enjoyable activity, providing you withhours of pleasure. However, it is essential tofamiliarize yourself with the operation of thewatercraft to achieve the skill level neces-sary to enjoy riding safely. Before operatingthis watercraft, read this Owner’s/Operator’sManual, the Riding Practice Guide, theRiding Instruction card and all warning andcaution labels on the watercraft. Pay particu-lar attention to the safety information onpages 1-8 to 1-15. Also, watch the BasicOrientation Video provided with your water-craft. These materials should give you anunderstanding of the watercraft and its oper-ation.

Remember: This watercraft is designed tocarry the operator and up to 2 passengers.Never exceed the maximum load limit orallow more than 3 persons (or 2 persons if awater-skier is being pulled) to ride the water-craft at one time.

EJU00474

Learning to operate your watercraft

Before operating the watercraft, alwaysperform the pre-operation checks listed onpage 3-5. The short time spent checking thewatercraft will reward you with added safetyand reliability.

Check state and local laws before operat-ing your watercraft.

Operate defensively at safe speeds andkeep a safe distance away from people,objects, and other watercraft. Select a widearea to learn in, where you have good visi-bility and light boat traffic.

Use the buddy system—operate withsomeone nearby. Scan constantly for peo-ple, objects, and other watercraft. Be alertfor conditions that limit your visibility or blockyour vision of others.

Attach the engine shut-off cord (lanyard)to your wrist and keep it free from the han-dlebars so that the engine stops if the opera-tor falls off.

Wear a personal flotation device (PFD).All riders must wear a Coast Guardapproved PFD that is suitable for personalwatercraft use.

Maximum load: 240 kg (530 lb)Load is the total weight of cargo, opera-tor and passengers.

3-21

E

Wear protective clothing. Severe internalinjuries can occur if water is forced into bodycavities as result of falling into the water orbeing near the jet thrust nozzle. Normalswimwear does not adequately protectagainst forceful water entry into rectum andvagina. All riders must wear a wetsuit bot-tom or clothing that provides equivalent pro-tection.

Such clothing includes thick, tightlywoven, sturdy and snug-fitting apparel suchas denim, but does not include spandex orsimilar fabrics like those used in bicycleshorts. A full wetsuit can also protect againsthypothermia (subnormal body temperature)and abrasions.

Footwear and gloves are recommended.Eye protection is recommended to keep

wind, water, and glare from the sun out ofyour eyes while you operate your watercraft.Restraining straps for eyewear are madewhich are designed to float should your eye-wear fall in the water.

You should grip the handlebars firmly andkeep both feet on the floor of the footwell. Donot attempt to ride with passengers untilyour operating skills are fully developed.

EJU00736

Riding watercraft with passengers

When 2 or 3 persons (including the oper-ator) are on board, the watercraft handlesdifferently, and is not as easy to maneuver,so operating it requires a higher degree ofskill. Before attempting to operate the water-craft with passengers on board, the operatormust practice operating the watercraft aloneenough to be able to acquire the necessaryskills.

The passengers must always wear USCGapproved PFD and wetsuit bottom or equiv-alent.

WARNINGDo not apply throttle when anyone is atrear of watercraft. Turn engine off or keepengine at idle. Water and/or debris exit-ing the jet thrust nozzle can cause severeinjury. Passengers should not attempt toboard the watercraft if the operator isapplying throttle.

Do not give a ride to children whose feetcannot reach the floor of the footwell. Pas-sengers should hold on firmly to the personin front of them and keep both feet in thefootwell.

WARNINGWhen passengers are on board, makesure that they are holding on firmly andhave feet in the footwell before you startto accelerate.

When pulling a skier, the spotter shouldface to the rear while holding the handgripwith both hands. The spotter should alwayssit astride the seat with his or her feet placedfirmly on the footrest for proper balance. Fol-low state laws regarding skiing such asskier-down flags, rearward-facing spotter,and other requirements.

3-22

E

EJU00484

Starting the watercraft

WARNING● Scan constantly for people, objects

and other watercraft. Be alert for con-ditions that limit your visibility or blockyour vision of others.

● Operate defensively at safe speedsand keep a safe distance away frompeople, objects, and other watercraft.

● Do not follow directly behind water-craft or other boats. Do not go nearothers to spray or splash them withwater. Avoid sharp turns or othermaneuvers that make it hard for othersto avoid you or understand where youare going. Avoid areas with sub-merged objects or shallow water.

● Take early action to avoid collisions.Remember watercraft and other boatsdo not have brakes. Do not release thethrottle when trying to steer away fromobjects—you need throttle to steer.

● Practice reboarding in shallow waterbefore riding in deep water.

3-23

E

EJU00486a

Starting and boarding in shallowwater1. Do not start the engine in less than

60 cm (2 ft) of water. Put the watercraftin water that is deep enough, and thenboard the watercraft from the side or therear.

2. Attach the engine shut-off cord to yourleft wrist, and then install the clip to theengine shut-off switch.

3. Grip the handlebars with both hands,place both feet on the floor of the foot-well, start the engine, and start off.

Starting from a dock1. Board the watercraft from the side.2. Attach the engine shut-off cord to your

left wrist, and then install the clip to theengine shut-off switch.

3. Push the watercraft away from the dock,grip the handlebars with both hands,place both feet on the floor of the foot-well, start the engine, and start off.

3-24

E

EJU00490a

Boarding and starting in deep water

WARNING● Operator and passenger should prac-

tice getting on board in shallow waterbefore riding in deep water. Boardingin deep water requires more skill.

● The fatigue and exposure that couldresult after unsuccessful attempts toget back on the watercraft mayincrease the risk of injuries and drown-ing.

Boarding alone1. Swim to the rear of the watercraft and

place both hands on the boarding plat-form, pull yourself up, and then grasp thehandgrip with one hand.

2. Pull yourself up to a kneeling position onthe platform, and then move to the seatand sit astride.

3. Attach the engine shut-off cord to yourwrist, and then install the clip to theengine shut-off switch.

4. Grip the handlebars firmly with bothhands, place both feet in footwell, startthe engine, and look in all directionsbefore starting off.

WARNINGBefore starting off, make sure that thereare no boats, obstructions, or swimmersaround you.

3-25

E

EJU00737a

Boarding with passengers

WARNINGSevere internal injuries can occur ifwater is forced into body cavities as aresult of being near the jet thrust nozzle.Do not apply throttle until each passen-ger is seated with his or her feet on thefloor of the footwell and is holding on tothe person in front of him or her.

1. Climb on board as noted in the previoussection, and sit astride the seat. Attachthe engine shut-off cord to your wrist,and then install the clip to the engineshut-off switch.

2. Have the passenger move to the rear ofthe watercraft.

3. Have the passenger get on board and siton the seat. If a second passenger isgetting on, have him or her follow thesame procedure.

NOTE:When a passenger is getting on board, bothhe and the operator should try to balancethe watercraft.

4. The operator should check to see thatthe passengers have their feet on thefloor of the footwell and that they aresecurely holding on to the person in frontof them.

5. Start the engine, look in all directions,and then accelerate to planing speed.

WARNINGBefore starting off, make sure that thereare no boats, obstructions, or swimmersaround you.

3-26

E

NOTE:The heavier the total weight of the operatorand passengers, the more difficult it will beto balance the watercraft. Do not operate thewatercraft when the total weight exceeds240 kg (530 lb) including any cargo. If it isdifficult to balance the watercraft at a stand-still, proceed as follows:1. The passenger must steady the water-

craft while the operator is boarding. Theoperator pulls himself up onto the plat-form into a seating position, then bal-ances the watercraft.

2. Attach the lanyard to your left wrist, theninstall the clip on the lanyard to theengine shut-off switch. Start the engineand keep it at idle.

3. The passenger pulls himself up on theplatform kneels down, then crawls ontothe seat as the watercraft accelerates.

4. The watercraft can now be acceleratedto planing speed, then the operator canreduce the throttle to the desired runningspeed.

EJU00677a

Capsized watercraftIf the watercraft capsizes, follow the pro-

cedures below carefully to prevent damageor injury.

WARNINGIMPROPER UPRIGHTING CAN CAUSEINJURY:● Shut engine off, and be sure engine

shut-off cord is removed from theengine shut-off switch.

● Do not put hand in intake grate.● Watch so you are not hit by the water-

craft as it comes over.

3-27

E

CAUTION:Be sure to remove the clip from theengine shut-off switch, otherwise theengine will overheat and engine damagemay occur.

1. Shut the engine off by removing the clipfrom the engine shut-off switch.

2. Swim to the rear of the watercraft. Pullthe watercraft over with left hand on rideplate while pushing down on the gun-wale with your right hand/foot.

NOTE:If the port side of the capsized watercraft istilting upward, first tilt the watercraft so theport side is down by using your weight topress down on the rub rail.

CAUTION:Do not turn the watercraft over counter-clockwise, otherwise water may leak intothe carburetor and engine and causedamage.

3. Start the engine, and then head forshore to inspect the engine for waterdamage.

CAUTION:If the watercraft has been capsized for5 minutes or more, air may have enteredthe oil injection system. Leave the engineoff, or operate only at trolling speed, for10 minutes after the watercraft has beenturned right-side up. This will allow anyair to bleed off.

3-28

E

EJU00499

Turning the watercraftSteering control depends on the combi-

nation of handlebar position and the amountof throttle.

Water sucked in through the intake grateis pressurized by the impeller in the jetpump. As the pressurized water is expelledfrom the pump through the jet thrust nozzle,it creates thrust to move and steer thewatercraft. The higher the engine speed, themore thrust is produced.

The amount of jet thrust, in addition to theposition of the handlebars, determines howsharply you turn.A. More throttle produces higher thrust, so

the watercraft will turn more sharply. B. Less throttle produces lower thrust, so

the watercraft will turn more gradually.C. Releasing the throttle completely pro-

duces only minimum thrust. If you aretraveling at speeds above trolling, youwill have rapidly decreasing ability tosteer without throttle. You may still havesome turning ability immediately afterreleasing the throttle, but once theengine slows down, the watercraft will nolonger respond to handlebar input untilyou apply throttle again or you reach atrolling speed.At trolling speed, the watercraft can beturned gradually by handlebar positionalone using just the amount of thrustavailable at idle.

D. If the engine is stopped while riding,there is no thrust. The watercraft will gostraight even though the handlebars areturned.

You need throttle to steer.

3-29

E

WARNING● Do not release the throttle when trying

to steer away from objects—you needthrottle to steer. A collision couldresult in severe injury or death.

● When operating at higher speeds,make gradual turns or slow downbefore turning. Sharp high-speed turnsmay cause the watercraft to slide side-ways or spin, throwing the operatorand passengers overboard whichcould cause an injury.

3-30

E

EJU00621

Stopping the watercraftThe watercraft is not equipped with a sep-

arate braking system. It is stopped by waterresistance when the throttle lever isreleased. From full speed, the watercraftcomes to a complete stop in approximately110 m (360 ft) after the throttle is releasedand the engine is stopped, although this dis-tance will vary depending on many factors,including gross weight, water surface condi-tions, and wind direction. The watercraftslows down as soon as the throttle lever isreleased, but will coast for a distance beforefully stopping. If you are not sure you canstop in time before hitting an obstacle, applythrottle and turn in another direction.

WARNING● Allow adequate stopping distance. ● Take early action to avoid collisions.

Remember, watercraft and other boatsdo not have brakes.

● Operate defensively at safe speedsand keep a safe distance away frompeople, objects, and other watercraftto give you time to stop.

● Do not shut the engine off when slow-ing down in case you need enginepower to steer away from a boat orother obstacle that comes into yourpath.

WARNINGDo not use the reverse function to slowdown or stop the watercraft as it couldcause you to lose control, be ejected, orimpact the handlebars.

3-31

E

EJU00635

Beaching the watercraft1. Make sure no obstructions, boats or

swimmers are near the beach. Releasethe throttle lever about 110 m (360 ft)before you reach the intended beachingarea.

2. Approach the beach slowly and stop theengine before reaching land. Remem-ber: you need throttle to steer.

3. Get off the watercraft and pull it up onthe beach.

CAUTION:Small pebbles, sand, seaweed, and otherdebris can be pulled into the jet intakeand impair or damage the impeller.Always stop the engine and get offbefore beaching the watercraft.

EJU00505

Docking the watercraft1. Make sure that no obstructions, boats or

swimmers are close to the watercraft.Reduce speed about 110 m (360 ft)away from the dock.

2. Slowly approach the dock and stop theengine just before coming alongside it.

3-32

E

EJU00006n

Reverse on waterways Reverse can be used for slow speed

maneuvering when it is necessary to backup out of tight spots where you cannot turnaround. Reverse can only be used to slowdown or stop during low speed maneuver-ing, such as when docking.

Once the engine is idling, shift to reverseand gradually increase engine speed. Makesure that there are no obstacles or peoplebehind you before shifting to reverse.

EJU00507

Rough water operationThe force of landing after jumping can

cause a strong impact on both the watercraftand the operator and passengers. It is pos-sible for the operator to hit his or her chest orjaw on the watercraft body or handlebarsand be injured. Do not operate the water-craft with your chin right above the handle-bars or with your feet outside the watercraft.Operating in rough water or jumping wavescan also crack the watercraft body or dam-age internal parts. Avoid operating in roughwater or bad weather conditions.

3-33

E

EJU00691a

Post-operation checksAlways perform the following post-opera-

tion checks after operating the watercraft.1. Remove the watercraft from the water.2. Wash down the hull, handlebars, and jet

unit with fresh water.3. Remove the seat and check the engine

compartment for water. To drain excesswater, remove the stern drain plugs, thenraise the bow of the watercraft enough toallow water in the bilge to drain out.

NOTE:This watercraft is equipped with an auto-matic bilge-draining system that removeswater from the engine compartment whileyou are underway. However, some residualwater will remain.

4. Put the watercraft in a horizontal posi-tion.

5. Flush the cooling system to prevent itfrom clogging with salt, sand, or dirt.(See page 4-1 for flushing the coolingsystem procedures.)

6. Drain residual water from the exhaust sys-tem by running the engine at 4,000 r/minfor a period of 10 to 15 seconds.

WARNINGStay away from the stern when theengine is running on load. Hot water andsteam spurting from exhaust outlet intothe air can cause serious burns.

CAUTION:Do not run the engine over 4,000 r/min onland. The catalytic converter could resultin serious damage.

3-34

E

7. If the watercraft will be stored for a weekor more, lubricate internal engine com-ponents to help prevent corrosion. (Seepage 4-3 for lubrication procedures.)

8. Rinse the engine and engine compart-ment with a small amount of water.

CAUTION:Do not use high pressure when rinsingthe engine or engine compartment assevere engine damage could result.

9. Wipe the engine and engine compart-ment dry with a clean cloth (repeatstep 3, if necessary).

10. Wipe the hull, handlebars, and jet unitdry with a clean cloth.

11. Spray a rust inhibitor, such as YamahaSilicone Protectant and Lubricant, onmetallic parts to minimize corrosion.

WARNINGDo not spray flammable rust inhibitorproducts on engine surfaces while theengine is hot. The sprayed substance orpropellants could catch fire.

12. Allow the engine compartment to air drycompletely before reinstalling the seat.

3-35

E

EJU00679

Transporting

WARNINGAlways place the fuel cock knob in the“OFF” position when transporting thewatercraft, otherwise fuel could leak outinto the engine or engine compartment,which would create a fire hazard.

When transporting the watercraft on atrailer, secure the tie downs to the trailerthrough the bow eye and stern rope hole.

CAUTION:● Do not route ropes or tie downs over

the seat, as they may leave permanentmarks on the seat’s surface. Also,wrap the ropes or tie downs with tow-els or rags where they touch the bodyof the watercraft to avoid scratching ordamage.

● Before putting the watercraft on thetrailer or transporting it, be sure to putthe shift lever in the forward position,otherwise the reverse gate may hit anobstruction, which may cause dam-age.

E

4

EJU00515

MAINTENANCE AND CARE

Storage.......................................................4-1Flushing the cooling system...................4-1Lubrication...............................................4-3Fuel system.............................................4-3Battery.....................................................4-4Cleaning the watercraft...........................4-5

Maintenance and adjustments ...............4-6Owner’s/Operator’s Manual and tool kit .............................................................4-7Periodic maintenance chart....................4-8Inspecting the fuel system......................4-9Inspecting the oil injection system........4-11Inspecting the steering cable................4-12Inspecting the shift cable ......................4-12Inspecting and adjusting the throttle cable......................................................4-12Inspecting the QSTS mechanism ........4-13Cleaning and adjusting the spark plugs......................................................4-14Lubrication points..................................4-15Adjusting the choke cable.....................4-18Inspecting the battery ...........................4-19Adjusting the carburetor .......................4-21Replacing the fuse................................4-22Bleeding the oil injection pump.............4-22

Specifications .........................................4-23

4-1

E

EJU00516a

Storage

WARNINGAlways place the fuel cock knob in the“OFF” position when storing the water-craft, otherwise fuel could leak out intothe engine or engine compartment,which would create a fire hazard.

Storage for prolonged periods of time,such as winter storage, requires preventa-tive maintenance to ensure against deterio-ration. It is advisable to have the watercraftserviced by a Yamaha dealer prior to stor-age. However, the following procedures canbe performed by the owner.

EJU00913a

Flushing the cooling systemFlushing the cooling system is essential

to prevent the cooling system from beingclogged with salt, sand, or dirt.

WARNINGStay away from stern when engine is run-ning on land. Hot water and steam spurt-ing from exhaust outlet into the air cancause serious burns.

CAUTION:● Do not supply water to the cooling

water passages when the engine is notrunning. The water could flow backthrough the muffler into the crankcasecausing severe engine damage.

● Do not run the engine for more15 seconds without supplying water,otherwise the engine may overheat.

● Do not run the engine over 4,000 r/minon land. The catalytic converter couldresult in serious damage.

4-2

E

1. Put the watercraft on land in a horizontalposition.

2. Open the flushing hose connector cap 1,and then insert the garden hose adapter 2into the flushing hose connector 3 andturn it until it is securely connected.

3. Connect the garden hose adapter to awater tap using a hose.

4. Start the engine, and then immediatelyturn the water supply on until water flowsout continually from the cooling waterpilot outlet.

5. Run the engine at idling speed for about3 minutes watching the engine condition.If the engine stops while flushing, turnthe water supply off immediately andrepeat the above steps.

6. Turn off the water supply. Then, force theremaining water out from the coolingpassages by running the engine at4,000 r/min or less within 10 to15 seconds.

7. Stop the engine.8. Remove the garden hose adapter and

secure the cap.

4-3

E

EJU00526a

Lubrication

WARNINGDo not spray flammable rust inhibitorproducts on engine surfaces while theengine is hot. The sprayed substance orpropellants could catch fire.

1. Remove the spark plugs and pourapproximately one tablespoon of oil intoeach cylinder.

2. Grease the spark plug threads and rein-stall the spark plugs.

3. Crank the engine within 3 seconds usingthe starter switch.

4. Lubricate all cables such as the throttle,choke, and steering cables.

NOTE:Use a Yamaha Power Cable Luber andYamaha Lube-Zall to pressure lubricate thecables and purge out any moisture betweenthe inner and outer cables.

5. Lubricate the areas of the watercraftspecified under Lubrication points onpage 4-15.

EJU00528b

Fuel system

WARNINGGasoline is highly flammable and explo-sive. A fire or explosion can causesevere injury or death. Shut off theengine. Do not smoke. Avoid spillinggasoline.

1. Place the fuel cock in the OFF position.2. Drain the fuel tank by using a siphon.

4-4

E

EJU00988

BatteryIf the watercraft is not used for a month or

more, disconnect the battery cable (–) first,and then the cable (+) and breather pipe,and next remove the battery from the craft.

Clean the battery casing using freshwater.

If the battery terminals are dirty or cor-roded, clean the mating surfaces on the ter-minals for the battery cables using the wiringbrush or equivalents.

Recharge the battery, and then store it ina cool and dark place.

Apply the Yamaha marine grease/Yamahagrease A to the battery terminals.

Recharge the battery periodically at least2 months because a battery will dischargeelectricity by itself while storing.

CAUTION:The battery may be impossible to useagain if you store it for a longer timewithout recharging. Recharge the batteryperiodically.

NOTE:The battery condition can be found bychecking the specific gravity of the electro-lyte. However, you can also know the batterycondition roughly by measuring the voltageat both battery terminals. Recharge the bat-tery if the voltage is 12 volts or less.

Yamaha recommend checking the specificgravity of the electrolyte and charging bat-tery by a Yamaha dealer or a battery dealer.If you maintain the battery yourself, readcarefully the instructions for the tool andmachine before maintenance.

Specific gravity of electrolyte (for reference):

1.28 at 20 °C (68 °F)

4-5

E

EJU00531

Cleaning the watercraftClean the watercraft before storing for a

long period.1. Wash down the hull, handlebars, and

drive unit with fresh water.2. Rinse the engine and bilge area with

fresh water. Drain off all water and wipeup remaining moisture with clean, dryrags.

3. Spray the engine’s exterior with YamahaSilicone Protectant and Lubricant.

WARNINGDo not spray flammable rust inhibitorproducts on engine surfaces while theengine is hot. The sprayed substance orpropellants could catch fire.

4. Wax the hull with a non-abrasive waxsuch as Yamaha Silicone Wax.

5. Wipe all vinyl and rubber components,such as the seat and engine compart-ment seals, with a vinyl protectant suchas Yamaha Protectant.

4-6

E

EJU00535a

Maintenance and adjustments

Periodic inspection, adjustment and lubri-cation will keep your watercraft in the safestand most efficient condition possible. Safetyis an obligation of the watercraft owner. Themost important points of watercraft inspec-tion, adjustment and lubrication areexplained on the following pages.

See your Yamaha dealer for genuineYamaha replacement parts and optionalaccessories designed for your watercraft.

Remember that failures that are the resultof the installation of parts or accessorieswhich are not qualitatively equivalent to gen-uine Yamaha parts are not covered by thelimited warranty.

Maintenance, replacement, or repair ofthe emission control devices and systemmay be performed by any marine enginerepair establishment or individual. War-ranty repair (emission or normal) how-ever, must be performed at an authorizedYamaha marine dealership.

WARNING● Be sure to turn off the engine when you

perform maintenance unless other-wise specified, otherwise an accidentor injury could result from unexpectedoperation, moving parts, or electricshock. If the owner is not familiar withwatercraft servicing, this work shouldbe done by a Yamaha dealer. Improp-erly serviced components could fail orstop operating correctly, which couldresult in an accident.

● Modifications to this watercraft notapproved by Yamaha may cause loss ofperformance or excessive noise, or ren-der it unsafe for use. Consult a Yamahadealer before attempting any changes.

4-7

E

NOTE:A service manual is available for purchasethrough a Yamaha dealer for owners whohave the mechanical skills, tools, and otherequipment necessary to perform mainte-nance not covered by this Owner’s/Opera-tor’s Manual.

Owner’s/Operator’s Manual and tool kit

It is advisable always to carry the Owner’s/Operator’s Manual and tool kit with youwhenever you use the watercraft. For yourconvenience, a storage compartment 1 isprovided on the watercraft for the manualand tool kit.NOTE:To protect these materials from water dam-age, it would be a good idea to put them in awaterproof bag. If your Owner’s/Operator’sManual is damaged, order a replacementfrom a Yamaha dealer.

The service information included in thismanual is intended to provide you with thenecessary information for completing yourown preventive maintenance and minorrepairs. The tools provided in the tool kit 2are sufficient for this purpose. However, atorque wrench may also be necessary totighten nuts and bolts.

4-8

E

EJU00536

Periodic maintenance chartThe following chart gives general guidelines for periodic maintenance. However, depend-

ing on your operating conditions maintenance may need to be performed more frequently.(●) This mark indicates maintenance that you may do yourself.(❍) This mark indicates work to be done by a Yamaha dealer.

*1: Grease capacity: 33.0–35.0 cm3 (1.11–1.18 oz)*2: Grease capacity: 6.0–8.0 cm3 (0.20–0.27 oz)

MAINTENANCE INTERVAL INITIALTHEREAFTER

EVERYPAGE

10hours

50hours

100hours

100hours

200hours

ITEM3

months6

months6

months12

monthsSpark plug Inspect, clean, adjust ● ● ● ● 4-14Lubrication points Lubricate ● ● 4-15Intermediate housing Lubricate ❍*1 ●*2 ●*2 4-18Fuel system Inspect ❍ ❍ 4-9Fuel filter Check, replace ❍ ❍ 4-10Fuel tank Clean ❍ 4-10Oil injection system Inspect, clean ❍ ❍ 4-11Trolling speed Adjust ● ● 4-21Carburetor throttle shaft Inspect ❍ ❍ —

Cooling water passages Flush ● (after every use)

4-1

Bilge strainer Clean ● ● ● —Impeller Inspect ● ● ● —Steering cable Inspect ● ● 4-12Steering master Inspect ❍ ❍ ❍ —QSTS mechanism Inspect ● ● 4-13Shift cable and mechanism Inspect, adjust ● ● 4-12Throttle cable Inspect, adjust ● ● 4-12Choke cable Inspect, adjust ● ● 4-18Stern drain plugs Inspect, replace ● 3-7

Battery Inspect

●(inspect fluid level before every use)

4-19

Rubber coupling Inspect ❍ —Nuts and bolts Retighten ❍ ❍ ❍ —

4-9

E

EJU00537

Inspecting the fuel system

WARNINGGasoline and its vapors are highly flam-mable and explosive.

Check the fuel system for leaks, cracks,or malfunctions. If any problem is found, dothe necessary repair or replacement asrequired. If repair is necessary, consult aYamaha dealer.Check:● Carburetor for leakage.● Fuel pump for malfunction or leakage.● Fuel tank for water or dirt.● Fuel tank for damage, cracks or leakage.● Fuel hose joint for leakage.● Fuel hose for cracks or other damage.● Fuel filter for leakage.● Fuel cock for leakage.● Air vent check valve for leakage.● Fuel tank filler cap for damage.

WARNINGFailure to check for and repair any fuelleakage may result in fire or explosion.

4-10

E

EJU00538

Fuel filterThis watercraft is equipped with a one-

piece, disposable fuel filter 1. The fuel filtershould be replaced once a year or afterevery 200 hours of operation, or if water isfound in the filter. Have a Yamaha dealerreplace the fuel filter if necessary.

WARNINGDo not try to replace the fuel filter your-self. An incorrectly installed filter canleak gasoline, which could lead to fire orexplosion. If necessary, have a Yamahadealer replace the fuel filter.

EJU00540

Fuel tankCheck the fuel tank 1 for leakage or

water in the tank. If water is found in the fuelsystem or if the fuel tank needs to becleaned have a Yamaha dealer service thewatercraft.

4-11

E

EJU00544

Inspecting the oil injection system

Check the oil injection system for leakage,cracks, or malfunctions. If necessary, have aYamaha dealer repair the oil injection sys-tem.Check:● Oil tank for damage, cracks or leakage.● Oil tank for water or dirt.● Oil hose and joint for damage or cracks.● Oil filter for dirt.● Oil pump for leakage.

Oil tankCheck the oil tank for leakage or water in

the tank. If water is found in the oil injectionsystem or if the oil tank needs to be cleanedhave a Yamaha dealer service the water-craft.

Oil filterCheck the oil filter for dirt and clogs. If the

oil filter is clogged, remove it from the oiltank together with the oil level sender andclean it.

4-12

E

EJU00546a

Inspecting the steering cableCheck for smooth operation of the handle-

bars and jet thrust nozzle.Turn the handlebars as far as possible to

the right and left and check that the distancebetween the jet thrust nozzle and thebracket of the reverse gate are equal onright and left sides.

If steering is stiff or misadjusted, have aYamaha dealer service it.

EJU00549a

Inspecting the shift cablePlace the shift lever in the reverse posi-

tion.Make sure the gate makes contact with the

stopper 1 on the bracket, and the arm 2makes contact with the reverse gate.

If the reverse gate does not reach the cor-rect positions, have a Yamaha dealer ser-vice it.

EJU00550

Inspecting and adjusting the throttle cable

Check that the throttle cable moves backto the set position smoothly and that freeplay is within specification. 1. Squeeze and release the throttle lever. If

the lever does not return smoothly, havea Yamaha dealer service it.

2. Adjust free play a by loosening the lock-nut 1 and turning the adjuster 2.

Distance A and B: A=B

Throttle lever free play:4.0–7.0 mm (0.16–0.26 in)

4-13

E

EJU00551

Inspecting the QSTS mechanism

Check that the shift lock lever moves backto the lock position smoothly, that the QSTSselector locks and unlocks properly, and thatthe jet thrust nozzle moves up or down.1. Squeeze and release the shift lock lever.2. Check that the QSTS selector locks

when the lever is released. 3. Check that the selector turns smoothly

when the lever is squeezed and held inplace.

4. Check that the angle of the jet thrustnozzle changes when the selector isshifted from neutral to bow-up or bow-down.

If the mechanism does not work properly,have a Yamaha dealer service it.

4-14

E

EJU00552a

Cleaning and adjusting the spark plugs

The spark plug is an important enginecomponent and is easy to inspect. The con-dition of the spark plug can indicate some-thing about the condition of the engine. Forexample, if the center electrode porcelain isvery white, this could indicate an intake airleak or carburetion problem in that cylinder.Do not attempt to diagnose any problemsyourself. Have a Yamaha dealer service thewatercraft.

Remove and inspect the spark plug peri-odically; heat and deposits will cause thespark plug to slowly break down and erode.If electrode erosion becomes excessive, or ifcarbon and other deposits are excessive,replace the spark plug with the specifiedplug.

Measure the spark plug gap a with awire thickness gauge before installing thespark plug. Adjust the gap to specification ifnecessary.

To reinstall spark plug:1. Clean the gasket surface.2. Wipe any dirt from the threads of the

spark plug.3. Screw the spark plug to the correct

torque.

Standard spark plug: BR8ES-11

Spark plug gap:1.0–1.1 mm (0.039–0.043 in)

Spark plug torque:25 N·m (2.5 kgf·m, 18 ft·lb)

4-15

E

NOTE:● Wipe off any water on the spark plug or

inside the cap before installing the sparkplug cap. Push the spark plug cap downuntil it clicks.

● If a torque wrench is not available whenyou are fitting a new spark plug, a goodestimate of the correct torque is 1/4 turnto 1/2 turn past finger tight. Have thespark plug adjusted to the correct torquewith a torque wrench as soon as possible.

WARNINGBe careful not to damage the insulatorwhen removing or installing a spark plug.A damaged insulator could allow sparksto escape, which could lead to explosionor fire.

EJU00553a

Lubrication pointsTo keep moving parts sliding or rotating

smoothly, coat them with water-resistantgrease.

Recommended water-resistant grease:Yamaha Marine Grease/Yamaha Grease A

● Throttle cable (carburetor end)● Oil pump cable

4-16

E

F0D4100

● Throttle cable (handlebar end)Squeeze the throttle lever and remove the

seal 1. Spray a rust inhibitor into the outercable. Refit the seal securely.

● Steering cable (handlebar end)

● Steering cable (nozzle end)● Nozzle pivot shaft● QSTS cable (nozzle end)

● QSTS cables (pulley end)

4-17

E

● QSTS cables (handlebar end)Remove the QSTS cable housing. Spray

a rust inhibitor into the outer cable.Reinstall the QSTS cable housing.

● Shift cable (lever end)

● Shift cable (reverse gate end)

● YPVS cable

4-18

E

EJU00566a

● Intermediate housingUsing a grease gun, fill the intermediate

housing with water-resistant grease throughthe grease nipple 1.

EJU00570

Adjusting the choke cableCheck that the choke cable is properly

adjusted.1. Pull the choke knob out until it stops, and

then release the knob. The knob shouldnot move.

2. If the choke knob moves back on its own,tighten the choke knob adjusting nut 1slightly. If the knob is difficult to move,loosen the adjusting nut slightly.

Grease capacity:Initial 10 hours or 1 month:

33.0–35.0 cm3 (1.11–1.18 oz)Every 100 hours or 6 months:

6.0–8.0 cm3 (0.20–0.27 oz)

4-19

E

EJU00572

Inspecting the batteryCheck the level of the battery electrolyte

and make sure the leads are secure.

WARNINGBattery electrolyte is poisonous and dan-gerous, causing severe burns, etc. Elec-trolyte contains sulfuric acid. Avoidcontact with skin, eyes or clothing.AntidotesExternal: Flush with water. Internal: Drink large quantities of wateror milk. Follow with milk of magnesia,beaten egg or vegetable oil. Call physi-cian immediately.Eyes: Flush with water for 15 minutesand get prompt medical attention.Batteries produce explosive gases. Keepsparks, flame, cigarettes, etc., well away.If using or charging the battery in anenclosed space, make sure that it is wellventilated. Always shield your eyes whenworking near batteries.KEEP OUT OF THE REACH OF CHIL-DREN.

CAUTION:Be careful not to place the battery on itsside.Make sure to remove the battery from thebattery compartment when adding bat-tery electrolyte or charging the battery.When checking the battery, make surethe breather hose is connected to thebattery and not obstructed.

4-20

E

To replenish the battery:1. Make sure that the electrolyte level is

between the upper 1 and lower 2 levelmarks.

2. Refill the battery with distilled water ifnecessary.

CAUTION:Normal tap water contains minerals thatare harmful to a battery. Use only dis-tilled water for replenishing the battery.

To recharge the battery:

CAUTION:Do not attempt to charge a battery hast-ily. Battery life may be shorter.

Yamaha recommend charging battery bya Yamaha dealer or a battery dealer. If youcharge the battery yourself, read the batterycharger instructions carefully before charg-ing and follow the points below.1. Remove all caps from the battery cell.2. Add distilled water to the specified level if

the electrolyte level is low.3. Set the charging rate to 1.9 ampere and

charge the battery slowly until the explo-sive gases become coming out vigor-ously from battery cells.

To connect the battery terminals:1. Make sure that the connections are correct

when you insert the battery in the watercraft. 2. Make sure that the breather hose is

properly connected and that it is notdamaged or obstructed.

3. Make sure that the battery is securelyheld in place.

1 Positive (+): Red lead2 Negative (–): Black lead3 Breather hose

4-21

E

EJU00573

Adjusting the carburetorThe carburetor is a vital part of the engine

and requires very sophisticated adjustment.Most adjusting should be left to a Yamahadealer who has the professional knowledgeand experience to perform it. However, theoperator may adjust the trolling speed aspart of the usual maintenance routine.

CAUTION:The carburetor was set at the Yamahafactory after many tests. If the settingsare disturbed by someone who does nothave the necessary technical knowledge,poor engine performance and damagemay result.

EJU00577a

Adjusting the trolling speed1. Put the watercraft in the water. 2. Start the engine and warm it up for 1 or

2 minutes. Using a diagnostic tachome-ter or, if necessary, the tachometer in themultifunction meter, adjust the enginespeed to specification.

3. Turn the throttle stop screw 1 clockwiseto increase engine speed if necessary.Turn it counterclockwise to decreaseengine speed if necessary.

Trolling speed: 1,300–1,400 r/min

4-22

E

EJU00578a

Replacing the fuseThe fuses are in the electrical box 1.

To replace the fuse:1. Remove the hose band a and keep the

duct hose b away from the electricalbox.

2. Remove the cap 2 on the electrical box.3. Remove the fuse using the fuse puller 3.4. Replace the fuse with one of the correct

amperage.

WARNINGDo not use fuses of higher amperage thatthose recommended. Substitution of afuse of improper rating can cause exten-sive electrical system damage and possi-ble fire.

EJU00580

Bleeding the oil injection pump

If the oil tank becomes completely empty,or any hose connected to the oil pump hasbeen disconnected, the oil pump must bebled to ensure proper oil flow.

If bleeding of the oil pump is necessary,have a Yamaha dealer bleed it.

Fuse amperage: 10 A, 20 A

4-23

E

EJU00588

SpecificationsMODEL

ITEMUnit XLT1200

WATERCRAFT CAPACITYMaximum people on board Number of people 3Maximum load capacity kg (lb) 240 (530)DIMENSIONSLength mm (in) 3,160 (125)Width mm (in) 1,220 (48)Height mm (in) 1,130 (45)Dry weight kg (lb) 364 (803)PERFORMANCEMaximum output kW (PS) @ r/min 114 (155)@ 7,000Maximum fuel consumption L/h (US gal/h, Imp gal/h) 64 (17, 14)Cruising range at full throttle hr. 1.09Trolling speed r/min 1,300–1,400ENGINEEngine type 2-stroke, L3Engine displacement cm3 (cu in) 1,176 (71.8)Bore & stroke mm (in) 80.0 × 78.0 (3.15 × 3.07)Compression ratio 5.9:1Lubrication system Variable oil injectionCooling system Water cooledStarting system Electric starterIgnition system Digital CDISpark plug BR8ES-11 (NGK)Spark plug gap mm (in) 1.0–1.1 (0.039–0.043)Battery capacity V-AH 12-19 Charging system Flywheel magnetoDRIVE UNITPropulsion system Jet pumpJet pump type Axial flow, single stageImpeller rotation Counterclockwise (viewed from rear)Transmission Direct drive from engineJet thrust nozzle horizontal angle Degree 24 + 24Jet thrust nozzle trim angle Degree -7, -2, 3, 8, 13FUEL AND OILRecommended fuel Regular unleaded gasolineMinimum octane rating PON

RON8690

Recommended engine oil YAMALUBE 2-W onlyFuel tank capacity

Total L (US gal, Imp gal) 70 (18.5, 15.5)Reserve L (US gal, Imp gal) 12 (3.2, 2.7)

Oil tank capacity L (US gal, Imp gal) 5.5 (1.5, 1.3)

E

5

EJU00594

TROUBLESHOOTING AND EMERGENCY

PROCEDURESTroubleshooting .......................................5-1

Troubleshooting chart.............................5-1Emergency procedures...........................5-4

Cleaning the jet intake and impeller.......5-4Jumping the battery ................................5-5Towing the watercraft .............................5-7Submerged watercraft ............................5-8

5-1

E

EJU00595

TroubleshootingIf you have any trouble with your watercraft, use this section to check for the possible

cause.If you cannot find the cause, or if the procedure for replacement or repair is not described

in this Owner’s/Operator’s Manual, have a Yamaha dealer perform the necessary service.

EJU00596a

Troubleshooting chartTROUBLE POSSIBLE CAUSE REMEDY PAGE

Engine does not start

Starter motor does not turn overMultifunction meter

“LOCK” mode selected Select “START” mode2-23

Engine shut-off switch

Clip not in place Install clip2-10

Fuse Burned out Replace the fuse and check wiring

4-22

Battery Run down Recharge 4-20Poor terminal connec-tions

Tighten as required4-20

Terminal corroded Clean 4-4Starter motor Faulty Have serviced by

Yamaha dealer—

Starter motor turns overFuel cock Turned to “OFF” Turn the fuel cock to

“ON”2-9

Fuel Empty Refill as soon as possi-ble

3-3

Stale or contaminated Have serviced by Yamaha dealer

4-9

Fuel tank Water or dirt present Have serviced by Yamaha dealer

4-10

Spark plug Fouled or defective Clean or replace 4-14Spark plug cap Not connected or loose Connect properly 4-14Crankcase Filled with water Crank engine with plug

out until clean5-8

Fuel filter Clogged or water pooled

Have serviced by Yamaha dealer

4-10

Choke Knob moves back on its own

Tighten the choke knob adjusting nut

4-18

Water temperature sensor

Failed Have serviced by Yamaha dealer —

5-2

E

Engine runs irregu-larly or stalls

Fuel Empty Refill as soon as possi-ble

3-3

Stale or contaminated Have serviced by Yamaha dealer

4-9

Choke Knob pulled Push fully in 2-10Fuel filter Clogged or water

pooledHave serviced by Yamaha dealer

4-10

Fuel tank Water or dirt present Have serviced by Yamaha dealer

4-10

Spark plug Fouled or defective Replace 4-14Incorrect heat range Replace 4-14Gap incorrect Adjust 4-14

Spark plug cap Loose Connect properly 4-14Cracked, torn, or dam-aged

Replace—

Electrical wir-ing

Loose connection Tighten or connect properly

—

Carburetor Incorrect idle adjust-ment

Adjust idle4-21

Clogged Have serviced by Yamaha dealer

—

Warning light or indicator blinks

Fuel level Empty Refill as soon as possi-ble

3-3

Engine oil level Empty Refill immediately 3-4Oil filter clogged Clean 4-11

Engine over-heated

Jet intake clogged Clean 5-4Water temperature sensor failed

Have serviced by Yamaha dealer

—

Low battery voltage

Battery voltage low Charge 4-20Battery terminal con-nected wrong

Connect properly4-20

Exhaust gas temperature

Too high Cool down engine2-19

TROUBLE POSSIBLE CAUSE REMEDY PAGE

5-3

E

Watercraft slow or loses power

Cavitation Jet intake clogged Clean 5-4Impeller damaged or worn

Have serviced by Yamaha dealer

—

Engine over-heated

Jet intake clogged Clean5-4

Fuel filter Clogged Have serviced by Yamaha dealer

4-10

Spark plug Fouled or defective Replace 4-14Incorrect heat range Replace 4-14Gap incorrect Adjust 4-14

Spark plug caps

Loose Connect properly4-14

Electrical wir-ing

Loose connection Tighten or connect properly

—

Fuel Stale or contaminated Have serviced by Yamaha dealer

4-9

Bilge Water in bilge Drain 3-7

TROUBLE POSSIBLE CAUSE REMEDY PAGE

5-4

E

EJU00597

Emergency proceduresEJU00598

Cleaning the jet intake and impeller

If weeds or debris get caught in the intakeor impeller, cavitation can occur, causing jetthrust to decrease even though enginespeed rises. If this condition is allowed tocontinue, the engine will overheat and mayseize. If there is any sign that the jet intakeor impeller is clogged with weeds or debris,beach the watercraft and check the intakeand impeller. Always stop the engine beforebeaching the watercraft.

WARNINGBefore attempting to remove weeds ordebris from the jet intake or impellerareas, shut the engine off and removethe clip from the engine shut-off switch.Severe injury or death could result fromcontact with the rotating parts of the jetpump.

1. Turn the watercraft on its side as shown.

CAUTION:● Place a suitable clean cloth or carpet-

ing underneath the watercraft to pro-tect it from abrasions and scratches.

● Always turn the watercraft over ontoits port (left) side.

● When turning the watercraft on itsside, support the bow so the handle-bars cannot be bent or damaged.

5-5

E

2. Remove any weeds or debris fromaround the drive shaft, impeller, pumphousing, and jet thrust nozzle.If debris is difficult to remove, consultyour Yamaha dealer.

CAUTION:Always avoid operating your watercraft inareas where weed growth is thick. If trav-eling in weeded areas is unavoidable,operate the engine alternately at partialthrottle and full throttle. Weeds tend toaccumulate more at a steady speed andat trolling speed. If weeds clog the intakeor impeller area and cause cavitation, fol-low the cleaning procedure above.

EJU00599

Jumping the batteryIf the watercraft battery has run down, the

engine can be started using a 12-volt bat-tery and jumper cables.

WARNINGBattery electrolyte is poisonous and dan-gerous, causing severe burns, etc. Elec-trolyte contains sulfuric acid. Avoidcontact with skin, eyes or clothing.AntidotesExternal: Flush with water. Internal: Drink large quantities of wateror milk. Follow with milk of magnesia,beaten egg or vegetable oil. Call physi-cian immediately.Eyes: Flush with water for 15 minutesand get prompt medical attention.Batteries give off explosive gases. Keepsparks, flame, cigarettes, etc. well away.If using or charging the battery in anenclosed area, make sure that it is wellventilated. Always shield your eyes whenworking near batteries.KEEP OUT OF THE REACH OF CHILDREN.

5-6

E

EJU00600

Connecting the jumper cables1. Connect the positive (+) jumper cable 2

to the positive (+) terminals of both bat-teries.

2. Connect one end of the negative (–)jumper cable 1 to the negative (–) termi-nal of the booster battery 3.

3. Connect the other end of the negative (–)cable to an unpainted bolt on the cylinderhead.

CAUTION:Do not connect the end of the jumpercable to the negative (–) terminal on thewatercraft battery! Be sure all connec-tions are secure and correct beforeattempting to start the engine. Anywrong connection may damage the elec-trical system.

4. Start the engine, and then disconnectthe cables by reversing the steps above.

CAUTION:● Never push the start switch while the

engine is running.● Do not operate the start switch for

more than 5 seconds, otherwise thebattery will be discharged and theengine will not start. Also, the startermotor may be damaged. If the enginedoes not start in 5 seconds, releasethe start switch, wait 15 seconds, andtry again.

5-7

E

EJU00603

Towing the watercraftIf the watercraft becomes inoperative in

the water, it can be towed to shore. If the watercraft must be towed in an

emergency using a tow line, the operatorshould ride the watercraft, holding onto thehandlebars.

CAUTION:● Tow the watercraft slowly; water may

enter the air intake and flood theengine compartment if the watercraftis towed too fast.

● Tow the watercraft using the bow eye 1only.

● The bow must be kept up out of thewater during towing to prevent waterfrom entering the engine compart-ment.

WARNING● The watercraft should only be towed in

an emergency. ● The tow line should be long enough so

that the watercraft will not collide withthe towing boat when slowing down. Agood rule of thumb is a tow line whichis three times the combined length ofthe towing boat and the watercraft. Ashorter length of rope can be used ifthe watercraft is towed very slowly.

● The operator of the towing boat mustkeep speed to a minimum and avoidtraffic or obstacles which could be ahazard to the rider on the watercraft.

5-8

E

EJU00604a

Submerged watercraftIf the watercraft is submerged or flooded

with water, follow the procedure below andconsult a Yamaha dealer as soon as possi-ble. Failure to do so may result in seriousengine damage!1. Beach the watercraft and remove the

stern drain plugs to drain the water fromthe engine compartment.

2. Turn the fuel cock knob to “OFF.”3. Remove the spark plugs and dry them

with a cloth.4. Without reinstalling the spark plugs,

crank the engine until all the water in thecylinders has been drained.

5. Install the stern drain plugs and thespark plugs.

6. Turn the fuel cock to “ON.”7. Launch the watercraft into the water, and

then run the engine for at least10 minutes. If the engine will not start,repeat steps above.

8. Turn the engine off. Turn the fuel cock to“OFF.”

9. Have the watercraft inspected by aYamaha dealer as soon as possible.

E

–MEMO–

E

6

EJU00608

APPENDIX

Limited warranty.......................................6-1

YAMAHA EXTENDED SERVICE (Y.E.S.) .......................................................6-3

Index...........................................................6-4

6-1

E

EJU00636

Limited warranty

YAMAHA MOTOR CORPORATION, U.S.A.WATER VEHICLE LIMITED WARRANTY

Yamaha Motor Corporation is proud of its heritage and reputation for producing products with high standards of quality and workman-ship. Product excellence provides the cornerstone for our commitment to customer satisfaction. The Yamaha Water Vehicle LimitedWarranty is your assurance of this commitment.

This warranty provides you with protection against the expense of repairs for your water vehicle that are required as a result of defectsin materials or workmanship. When maintained and utilized in the prescribed manner, you can count on your Yamaha water vehicle toprovide reliable service.

This warranty provides you with specific coverage and notes your responsibilities in maintaining and operating your water vehicle.Please take the time to read and become familiar with this warranty.

PERIOD OF WARRANTY. Any new Yamaha water vehicle purchased for pleasure use from an authorized Yamaha water vehicle dealerin the United States, will be warranted against defects in material or workmanship for a period of one (1) year from date of purchase,subject to exclusions noted herein. Any Yamaha Water Vehicle purchased and utilized for commercial applications will be warranted fora period of ninety [90] days from the date of purchase, subject to exclusions noted herein. Replacement parts used in warranty repairswill be warranted for the balance of the applicable warranty period.

The warranty described here applies to water vehicles purchased and registered for use in the United States only. For warranty provi-sions outside the United States, contact the particular country’s local Yamaha distributor.

OBTAINING REPAIRS UNDER WARRANTY. During the period of warranty, any authorized Yamaha water vehicle dealer will, free ofcharge, repair or replace, at Yamaha’s option, any parts adjudged defective by Yamaha due to faulty workmanship or material from thefactory. All parts replaced under warranty will become the property of Yamaha Motor Corporation, U.S.A.

CUSTOMER’S RESPONSIBILITY. Under the terms of this warranty, the customer will be responsible for ensuring that the water vehi-cle is properly operated, maintained, and stored as specified in the applicable Owner’s/Operator’s Manual.

The owner of the water vehicle shall give notice to an authorized Yamaha water vehicle dealer of any and all apparent defects within ten[10] days of discovery and make the vehicle available at that time for inspection and repairs at the dealer’s place of business.

GENERAL EXCLUSIONS FROM WARRANTY. This warranty will not cover the repair of damage if the damage is a result of abuse orneglect of the product. Examples of abuse and neglect include, but are not limited to:1. Racing or competition use, modification of original parts abnormal strain.2. Lack of proper maintenance and off season storage as described in the Owner’s/Operator’s Manual, installation of parts or accesso-

ries that are not equivalent in design and quality to genuine Yamaha parts.3. Use of lubricants, oils, and fuel/oil mixtures that are not suitable for water vehicle motor use.4. Damage as a result of accidents, collisions, contact with foreign materials, or submersion.5. Growth of marine organisms on motor or hull surfaces.6. Normal deterioration.7. Gel coat stress cracks.

SPECIFIC PARTS EXCLUDED FROM WARRANTY.Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are notcovered by warranty. Charges for transporting the water vehicle to and from an authorized Yamaha water vehicle dealer are excludedfrom warranty coverage.

TRANSFER OF WARRANTY. Transfer of the warranty from the original purchaser to any subsequent purchaser is possible by havingthe vehicle inspected by an authorized Yamaha water vehicle dealer and requesting the dealer to submit a change of registration toYamaha Motor Corporation. U.S.A. within ten [10] days of the transfer.

EMISSION CONTROL SYSTEM WARRANTY. Yamaha warrants to the ultimate purchaser and each subsequent, that this engine isdesigned, built, and equipped so as to conform at the time of sale with applicable regulations under section 213 of the Clean Air Actand this engine is free from defects in materials and workmanship which cause said engine to fail to conform with applicable regula-tions for one (1) year from date of purchase.

YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WAR-RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITSSTATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, U.S.A. AND EXCLUDED FROM THISWARRANTY.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOTAPPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSSOF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THEABOVE EXCLUSION MAY NOT APPLY TO YOU.

6-2

E

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TOSTATE.

YAMAHA MOTOR CORPORATION, U.S.A.Post Office Box 6555

Cypress, California 90630WARRANTY QUESTIONS AND ANSWERS

Q. What costs are my responsibility during the warranty period?A. The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision dam-

ages.

Q. What are some examples of “abnormal” strain, neglect, or abuse?A. These terms are general and overlap each other in areas. Specific examples include:

Running the water vehicle out of oil, operating the machine with a broken or damaged part which causes another part to fail, and soon. If you have any specific questions on operation or maintenance, please contact your Yamaha water vehicle dealer for advice.

Q. Does the warranty cover incidental costs such as transportation due to a failure?A. No. The warranty is limited to repair of the water vehicle itself.

Q. May I perform any or all of the recommended maintenance shown in the Owner’s/Operator’s Manual instead of having the dealer dothem?

A. Yes, if you are a qualified mechanic and follow the procedures specified in the Owner’s/Operator’s and Service Manual. We do rec-ommend, however, that items requiring special or equipment be done by a Yamaha water vehicle dealer.

Q. Will the warranty be void or cancelled if I do not operate or maintain my new water vehicle exactly as specified in the Owner’s/Oper-ator’s Manual?

A. No. The warranty on a new water vehicle cannot be “voided” or “cancelled”. However, if a particular failure is caused by opera-tion or maintenance other than as shown in the Owner’s/Operator’s Manual, that failure may not be covered under war-ranty.

Q. What responsibility does my dealer have under this warranty?A. Each Yamaha water vehicle dealer is expected to:

1.Completely set up each new water vehicle before sale.2.Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request at any

later date. In addition, each Yamaha water vehicle dealer is held responsible for his setup, service and warranty repair work.

Q. Is the warranty transferable to second owners?A. Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by an

authorized Yamaha water vehicle dealer for the policy to remain effective.

CUSTOMER SERVICE

If your water vehicle requires warranty service, you must take it to any authorized Yamaha water vehicle dealer within the continentalUnited States. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or prob-lem arises regarding warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, thisperson is in the best position to help you. If you are still not satisfied and require additional assistance, please write:

YAMAHA MOTOR CORPORATION U.S.A.CUSTOMER RELATIONS DEPARTMENT

P.O. Box 6555Cypress, California 90630

CHANGE OF ADDRESS

The federal government requires each manufacturer to maintain a complete, up-to-date list of all first purchasers against the possibilityof a safety-related defect and recall. This list is complied from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. bythe selling dealer at the time of your purchase.If you should move after you have purchased your new water vehicle, please advise us of your new address by sending a postcard list-ing your Yamaha model name, engine number, dealer number [or dealer’s name] as it is shown on your warranty card, your name andnew mailing address.Mail to:

YAMAHA MOTOR CORPORATION, U.S.A.P.O. Box 6555

Cypress, California 90630Attention: Warranty Department

This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.

6-3

E

YAMAHA EXTENDED SERVICE (Y.E.S.)Keep your Yamaha protected even after your warranty expires with genuine Yamaha ExtendedService (Y.E.S.).●●●● Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner

satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.●●●● Y.E.S. is flexible. You choose the plan that is right for you: 12 months, 24 months, or 36 months

beyond your warranty period.●●●● Y.E.S. is designed and administered by the same Yamaha people who handle your warranty

and it shows in the comprehensive coverage benefits. There are no mileage limitations. Cover-age is not limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. coversmanufacturing defects just like the warranty. See the sample contract at your Yamaha dealer tosee how comforting uninterrupted factory-backed protection can be.

●●●● You do not have to pay anything for covered repairs. There is no deductible to pay, and repairsare not “pro-rated.” You do not have any “out-of-pocket” expenses for covered repairs.

●●●● In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost.TRIP gives you up to $150 reimbursement per occurrence for any reasonable expenses youincur because your Yamaha needs covered service: replacement vehicle rental, emergencytowing, phone calls, even food and lodging when you are away from home. This superb cover-age goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well ascovered repairs during your entire Y.E.S. plan period.

●●●● Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.

●●●● Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make yourYamaha much more valuable!

This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only whileyour Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamahadealer to get all the facts. He can show you how easy it is to protect your investment with YamahaExtended Service.We urge you to act now. You will get the excellent benefits of TRIP coverage right away, and youwill rest easy knowing you will have strong factory-backed protection even after your YamahaLimited Warranty expires. You can also save money: Y.E.S. costs less within the first 90 daysafter you buy your Yamaha. See your dealer today!

A special note:If visiting your dealer is not convenient, contact Yamaha with your Primary ID number (your enginenumber). We will be happy to help you get the Y.E.S. coverage you need.

Yamaha Service MarketingP.O. Box 6555Cypress, CA 90630(714) 761-7631

6-4

E

EJU00609

Index2-stroke engine oil................................... 3-3AAdjusting the carburetor ........................ 4-21Adjusting the choke cable ..................... 4-18Adjusting the trolling speed ................... 4-21Approval label of Emission control certificate................................................. 1-2BBattery..............................................3-8, 4-4Battery warning indicator....................... 2-30Beaching the watercraft ........................ 3-31Bilge ........................................................ 3-7Bleeding the oil injection pump ............. 4-22Boarding alone ...................................... 3-24Boarding and starting in deep water ..... 3-24Boarding with passengers..................... 3-25Bow down.............................................. 2-16Bow up .................................................. 2-16CCapsized watercraft .............................. 3-26Caution labels ......................................... 1-6Choke knob ........................................... 2-10Cleaning and adjusting the spark plugs...................................................... 4-14Cleaning the jet intake and impeller ........ 5-4Cleaning the watercraft ........................... 4-5Clock ..................................................... 2-26Connecting the jumper cables................. 5-6Cooling water pilot outlet..............2-12, 3-13Crossing ................................................ 1-17Cruising limitations .................................. 1-9DDocking the watercraft .......................... 3-31EEmergency procedures ........................... 5-4Emission control information ................... 1-2Engine break-in ..................................... 3-14Engine compartment ............................... 3-6Engine oil meter .................................... 2-26Engine overheat warning indicator........ 2-29

Engine overheat warning system ..........2-17Engine serial number ..............................1-1Engine shut-off cord (lanyard) ...............3-12Engine shut-off switch ...........................2-10Engine stop switch ................................2-10Enjoy your watercraft responsibly .........1-21Exhaust temperature warning indicator.................................................2-30Exhaust temperature warning system...2-19FFilling the fuel tank ..................................3-3Filling the oil tank ....................................3-4Fire extinguisher......................................3-9Fishing vessel right-of-way....................1-18Flushing the cooling system....................4-1Front seat ................................................2-6Front storage compartment ...................2-31Fuel and oil..............................................3-1Fuel and oil systems ...............................3-6Fuel cock knob ........................................2-9Fuel filter ...............................................4-10Fuel meter .............................................2-25Fuel system.............................................4-3Fuel tank ...............................................4-10Fuel tank filler cap ...................................2-8Fuel warning indicator ...........................2-28GGasohol ...................................................3-2Gasoline ..................................................3-1Getting to know your watercraft ............3-20Give-way vessel ....................................1-16Glove compartment ...............................2-32HHandgrip................................................2-20Hazard information................................1-13Hood........................................................2-7Hour meter ............................................2-27Hull Identification Number (HIN)..............1-1IIdentification numbers .............................1-1Important labels.......................................1-3Inspecting and adjusting the throttle cable......................................................4-12

6-5

E

Inspecting the battery............................ 4-19Inspecting the fuel system....................... 4-9Inspecting the oil injection system......... 4-11Inspecting the QSTS mechanism.......... 4-13Inspecting the shift cable....................... 4-12Inspecting the steering cable ................ 4-12JJet unit................................................... 3-12Jumping the battery................................. 5-5LLabel location .......................................... 1-3Launching the watercraft....................... 3-16Learning to operate your watercraft ...... 3-20Leaving the watercraft........................... 3-19Limitations on who may operate the watercraft ................................................ 1-8Limited warranty...................................... 6-1Location of main components ................. 2-1Lubrication............................................... 4-3Lubrication points .................................. 4-15MMaintenance and adjustments ................ 4-6Manufactured date label.......................... 1-2Meeting ................................................. 1-17Multifunction meter.......................2-21, 3-13NNarrow channels and bends ................. 1-18OOil filter .................................................. 4-11Oil tank .................................................. 4-11Oil tank filler cap...................................... 2-8Oil warning indicator.............................. 2-29Operating your watercraft...................... 3-20Operation .............................................. 3-14Operation of controls and other functions.................................................. 2-5Operation requirements ........................ 1-10Other labels............................................. 1-7Other sources........................................ 1-20Other special situations......................... 1-18Overtaking............................................. 1-18Owner’s/Operator’s Manual and tool kit...................................................... 4-7

PPADLOC initial setting...........................2-22PADLOC (Programmable digital locking ignition)..................................................2-22Periodic maintenance chart.....................4-8Post-operation checks...........................3-33Pre-operation check list...........................3-5Pre-operation check points .....................3-6Pre-operation checks ..............................3-5Primary Identification (PRI-ID) number ...1-1QQuick Shift Trim System (QSTS) selector..................................................2-15RReading buoys and other markers ........1-18Rear seat.................................................2-5Replacing the fuse ................................4-22Reverse on waterways..........................3-32Riding watercraft with passengers ........3-21Rough water operation..........................3-32Rules of the Road .................................1-16Rules when encountering vessels.........1-17SSafety information ...................................1-8Sailing vessel right-of-way ....................1-18Seat storage compartment ....................2-32Selecting “PADLOC” mode ...................2-23Shift lever ..............................................2-14Shift lever and reverse gate ..................3-11Specifications ........................................4-23Speedometer.........................................2-25Stand-on vessel ....................................1-16Starting and boarding in shallow water .....................................................3-23Starting from a dock ..............................3-23Starting the engine ................................3-16Starting the watercraft ...........................3-22Start switch............................................2-11Steering and sailing rules ......................1-16Steering system ...........................2-12, 3-10Stopping the engine ..............................3-19Stopping the watercraft .........................3-30Storage....................................................4-1

6-6

E

Storage compartments.......................... 2-31Submerged watercraft............................. 5-8Switches................................................ 3-13TTachometer ........................................... 2-24Throttle .................................................. 3-10Throttle lever ......................................... 2-11Tilt lever................................................. 2-13To get more boating safety information ............................................ 1-20Towing the watercraft.............................. 5-7Transporting .......................................... 3-35Tripmeter............................................... 2-28Trip timer ............................................... 2-27Troubleshooting ...................................... 5-1Troubleshooting chart ............................. 5-1Turning the watercraft ........................... 3-28UUnited States Coast Guard ................... 1-20WWarning labels ........................................ 1-4Watercraft characteristics...................... 1-13Watercraft Education and Training........ 1-20Water separator ...................................... 3-7Water-skiing .......................................... 1-14YYAMAHA EXTENDED SERVICE (Y.E.S.).................................................... 6-3

Printed in USANovember 2000—3.0 × 1 CRF0V-F8199-10(XA1200A-Z)

Printed on recycled paper

YAMAHA MOTOR CORPORATION, USA