1800 Start

7/28/2019 1800 Start

1/25

Quick Start Guide

Cisco 1800 Series Integrated Services Router (Modular) Quick Start

GuideINCLUDING LICENSE AND WARRANTY

1 Cisco One-Year Limited Hardware Warranty Terms, page 2

2 Overview, page 3

3 Documents, Equipment, and Tools, page 3

4 Install Chassis, page 4

5 Connecting Cables, page 13

6 Power Up the Router, page 15

7 Interface Numbering, page 17

8 Perform Initial Configuration, page 18

9 Where to Go Next, page 22

10 Obtaining Documentation, page 23

11 Documentation Feedback, page 23

12 Obtaining Technical Assistance, page 23

13 Obtaining Additional Publications and Information, page 24

7/28/2019 1800 Start

2/25

2

1 Cisco One-Year Limited Hardware Warranty TermsThere are special terms applicable to your hardware warranty and various services that you can use during the warranty period.Your formal Warranty Statement, including the warranties and license agreements applicable to Cisco software, is available onCisco.com. Follow these steps to access and download the Cisco Information Packetand your warranty and license agreementsfrom Cisco.com.

1. Launch your browser, and go to this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htm

The Warranties and License Agreements page appears.

2. To read the Cisco Information Packet, follow these steps:

a. Click the Information Packet Number field, and make sure that the part number 78-5235-03A0 is highlighted.

b. Select the language in which you would like to read the document.

c. Click Go.

The Cisco Limited Warranty and Software License page from the Information Packet appears.

d. Read the document online, or click the PDF icon to download and print the document in Adobe Portable DocumentFormat (PDF).

Note You must have Adobe Acrobat Reader to view and print PDF files. You can download the reader from

Adobes website: http://www.adobe.com

3. To read translated and localized warranty information about your product, follow these steps:

a. Enter this part number in the Warranty Document Number field:

78-10747-01C0.

b. Select the language in which you would like to view the document.

c. Click Go.

The Cisco warranty page appears.

d. Review the document online, or click the PDF icon to download and print the document in Adobe Portable DocumentFormat (PDF).

You can also contact the Cisco service and support website for assistance:

http://www.cisco.com/en/US/support/

Duration of Hardware Warranty

One (1) Year

Replacement, Repair, or Refund Policy for Hardware

Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten (10) working days afterreceipt of a Return Materials Authorization (RMA) request. Actual delivery times can vary, depending on the customer location

Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.

To Receive a Return Materials Authorization (RMA) Number

Contact the company from whom you purchased the product. If you purchased the product directly from Cisco, contact yourCisco Sales and Service Representative.

Complete the information below, and keep it for reference.

Company product purchased from

Company telephone number

Product model number

Product serial number

Maintenance contract number
http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htmhttp://www.adobe.com/http://www.cisco.com/en/US/support/http://www.cisco.com/en/US/support/http://www.adobe.com/http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htm

7/28/2019 1800 Start

3/25

7/28/2019 1800 Start

4/25

7/28/2019 1800 Start

5/25

5

Warning Definition

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before youwork on any equipment, be aware of the hazards involved with electrical circuitry and be familiar withstandard practices for preventing accidents. Use the statement number provided at the end of eachwarning to locate its translation in the translated safety warnings that accompanied this device.Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kanveroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bijelektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijkenom ongelukken te voorkomen. Voor een vertaling van de waarschuwingen die in deze publicatie

verschijnen, dient u de vertaalde veiligheidswaarschuwingen te raadplegen die bij dit apparaatworden geleverd.

Opmerking BEWAAR DEZE INSTRUCTIES.

Varoitus TRKEIT TURVALLISUUTEEN LIITTYVI OHJEITA

Tm varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuintyskentelet minkn laitteiston parissa, ota selv shkkytkentihin liittyvist vaaroista jatavanomaisista onnettomuuksien ehkisykeinoista. Tss asiakirjassa esitettyjen varoitustenknnkset lydt laitteen mukana toimitetuista ohjeista.

Huomautus SILYT NM OHJEET

Attention IMPORTANTES INFORMATIONS DE SCURIT

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causerdes blessures ou des dommages corporels. Avant de travailler sur un quipement, soyez conscient desdangers poss par les circuits lectriques et familiarisez-vous avec les procdures courammentutilises pour viter les accidents. Pour prendre connaissance des traductions d'avertissementsfigurant dans cette publication, consultez les consignes de scurit traduites qui accompagnent cetappareil.

Remarque CONSERVEZ CES INFORMATIONS

Warnung WICHTIGE SICHERHEITSANWEISUNGEN

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Krperverletzungfhren knnte. Bevor Sie mit der Arbeit an irgendeinem Gert beginnen, seien Sie sich der mitelektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung vonUnfllen bewusst. bersetzungen der in dieser Verffentlichung enthaltenen Warnhinweise sind imLieferumfang des Gerts enthalten.

Hinweis BEWAHREN SIE DIESE SICHERHEITSANWEISUNGEN AUF

7/28/2019 1800 Start

6/25

6

Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone.Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi aicircuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Per le traduzionidelle avvertenze riportate in questo documento, vedere le avvertenze di sicurezza che accompagnanoquesto dispositivo.

Nota CONSERVARE QUESTE ISTRUZIONI

Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER

Dette varselssymbolet betyr fare. Du befinner deg i en situasjon som kan forrsake personskade. Frdu utfrer arbeid med utstyret, br du vre oppmerksom p farene som er forbundet med elektriskekretssystemer, og du br vre kjent med vanlig praksis for unng ulykker. For se oversettelser avadvarslene i denne publikasjonen, se de oversatte sikkerhetsvarslene som flger med denne enheten.

Merk TA VARE P DISSE INSTRUKSJONENE

Aviso INSTRUES IMPORTANTES DE SEGURANA

Este smbolo de aviso significa perigo. O utilizador encontra-se numa situao que poder sercausadora de leses corporais. Antes de iniciar a utilizao de qualquer equipamento, tenha emateno os perigos envolvidos no manuseamento de circuitos elctricos e familiarize-se com asprticas habituais de preveno de acidentes. Para ver tradues dos avisos includos nestapublicao, consulte os avisos de segurana traduzidos que acompanham este dispositivo.

Nota GUARDE ESTAS INSTRUES

Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este smbolo de aviso indica peligro. Existe riesgo para su integridad fsica. Antes de manipularcualquier equipo, considere los riesgos de la corriente elctrica y familiarcese con losprocedimientos estndar de prevencin de accidentes. Vea las traducciones de las advertencias queacompaan a este dispositivo.

Nota GUARDE ESTAS INSTRUCCIONES

Varning! VIKTIGA SKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.Innan du utfr arbete p ngon utrustning mste du vara medveten om farorna med elkretsar och knnatill vanliga frfaranden fr att frebygga olyckor. Se versttningarna av de varningsmeddelanden somfinns i denna publikation, och se de versatta skerhetsvarningarna som medfljer denna anordning.

OBS! SPARA DESSA ANVISNINGAR

7/28/2019 1800 Start

7/25

7

Aviso INSTRUES IMPORTANTES DE SEGURANA

Este smbolo de aviso significa perigo. Voc se encontra em uma situao em que h risco de lesescorporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem oscircuitos eltricos e familiarize-se com as prticas padro de preveno de acidentes. Use o nmeroda declarao fornecido ao final de cada aviso para localizar sua traduo nos avisos de seguranatraduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUES

7/28/2019 1800 Start

8/25

8

Advarsel VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse.Fr du begynder arbejde p udstyr, skal du vre opmrksom p de involverede risici, der er vedelektriske kredslb, og du skal stte dig ind i standardprocedurer til undgelse af ulykker. Brugerklringsnummeret efter hver advarsel for at finde oversttelsen i de oversatte advarsler, der fulgtemed denne enhed.

GEM DISSE ANVISNINGER

7/28/2019 1800 Start

9/25

9

Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord. Statement 1

Warning Read the installation instructions before connecting the system to the power source. Statement 1004

Warning Take care when connecting units to the supply circuit so that wiring is not overloaded. Statement 1018

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.Statement 1030

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

7/28/2019 1800 Start

10/25

10

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommendedambient temperature of 40 deg. Statement 1047

Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or

equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturersinstructions. Statement 1015

Installing the Router

Note Cisco 1800 series routers are normally ordered with modules and interface cards. Before you remove or install anymodules or interface cards, refer to the documents that accompany those items or to the online Cisco 1800 serieshardware installation documentation at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/hw/index.htm

You can set any Cisco 1800 series router on a desktop. See the applicable instructions in the following section:

Installing the Router on a Desktop, page 10

Caution To prevent damage to the chassis, never attempt to lift or tilt the chassis by the plastic panel on the front. Alwayshold the chassis by the metal body.

Installing the Router on a Desktop

The Cisco 1841 router is shipped with the rubber feet attached to the chassis.

Caution Your chassis installation must allow unrestricted airflow for chassis cooling. For placing on a desktop, keep at leastone inch of clear space beside the cooling inlet and exhaust vents.

Caution Do not place any items that weigh more than 10 pounds (4.5 kilograms) on top of the chassis, and do not stackrouters on top of each other.

Grounding the Chassis

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of

a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician ifyou are uncertain that suitable grounding is available. Statement 1024

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch thebackplane with your hand or any metal tool, or you could shock yourself. Statement 94
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/hw/index.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/hw/index.htm

7/28/2019 1800 Start

11/25

11

Warning This equipment needs to be grounded. Use a green and yellow 14 AWG ground wire to connect the host to earthground during normal use. Statement 190

To connect the chassis to a reliable earth ground, using a ring terminal and size 14 AWG (2 mm2) wire, follow these steps:

7/28/2019 1800 Start

12/25

12

Step 1 Strip one end of the ground wire to expose approximately 3/4 inch (20 mm) of conductor.

Step 2 Crimp the 14 AWG green ground wire to a UL Listed/CSA certified ring terminal, using a crimping tool that isrecommended by the ring terminal manufacturer. The ring terminal provided on the back panel of the router is suitablefor a No. 6 grounding screw.

Step 3 Attach the ring terminal to the chassis as shown in Figure 1. Use a number 2 Phillips screwdriver and the screw suppliedwith the ring terminal. Tighten the screw to a torque of 8 to 10 inch-pounds (0.9 to 1.1 newton meters.)

Step 4 Connect the other end of the ground wire to a known good electrical grounding point such as a service panel grounding lug.Consult a licensed electrician if you have any questions about the suitability of the ground connection.

Figure 1 Chassis Ground Connection on the Cisco 1841 Router

5 Connecting Cables

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

This section provides an overview of the cabling for different ports and connections on the Cisco 1841 router.For detailed information on the connections, cables, and pinouts, refer to the following documents:

Cisco Interface Cards Installation Guide at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis2600/hw_inst/wic_inst/wic_doc/index.htm

Cisco Modular Access Router Cable Specifications at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/hw_inst/cabling/marcabl.htm

WAN and LAN Connections

The connections and cables listed in Table 1 are described in detail in the Cisco 1800 series hardware installation documents atthe following URL:


Caution Do not connect a WAN, telephone, or fax cable to an interface card until you have completed the installationprocedure.

Warning Hazardous network voltages are present in WAN ports regardless of whether power to the router is OFF or ON. Toavoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end awayfrom the router first. Statement 1026

117083

Ring terminalattachment

CISCO1841

100-240 VAC-1 A

50/60 Hz
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis2600/hw_inst/wic_inst/wic_doc/index.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/hw_inst/cabling/marcabl.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/hw/index.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/hw/index.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/hw_inst/cabling/marcabl.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis2600/hw_inst/wic_inst/wic_doc/index.htm

7/28/2019 1800 Start

13/25

13

Table 1 summarizes the basic WAN and LAN connections for the Cisco 1841 router.

Console, Auxiliary, and USB Port Connections

The connections described in Table 2 provide system management access.

Note The USB port (version 1.1) is intended for future use only.

Table 1 WAN and LAN Connections

Port or Connection Port Type, Color1

1. The color codes are specific to cables shipped by Cisco

Connected To: Cable

Fast Ethernet (FE) RJ-45, yellow Ethernet hub Crossover to connect to a router

Straight-through to connect to a

switch

T1/E1 WAN RJ-48C T1 or E1 network or CSU/DSU RJ-48 T1/E1 straight-through(Crossover to connect ot a PBX orany other equipment)

Cisco serial (1T) 60-pin D-sub, blue CSU/DSU and serial network orequipment

Cisco serial transition cable thatmatches the signaling protocol(EIA/TIA-232, EIA/TIA-449, V.35,X.21, or EIA/TIA-530) and the serialport operating mode (DTE or DCE).

Refer to the Cisco Modular AccessRouter Cable Specificationsdocument for information about

selecting these cables.

Cisco Smart serial (2T) Cisco Smart compactconnector, blue

CSU/DSU and serial network orequipment

For WIC-2T and WIC-2A/S only

DSL RJ-11C/RJ-14C Network demarcation device forservice providers DSL interface

RJ-11 straight-through for 2-wire

RJ-14 straight-through for 4-wire

BRI S/T WAN(external NT12)

2. NT1 = Network Termination 1

RJ-45, orange NT1 device or PINX3

3. PINX = Private integrated network exchange

RJ-45 straight-through

BRI U WAN(built-in NT1)

RJ-49C/CA-A11,orange

ISDN network RJ-49 straight-through

Analog modem RJ-11 PSTN RJ-11 straight-through

56/64-kbpsCSU/DSU

8-pin modular RJ-48S interface RJ-48 straight-through

Table 2 Console and Auxiliary Port Connections

Port or Connection Color or Type Connected To: Cable

Console Light blue PC or ASCII terminal communicationport (usually labeled COM)

RJ-45-to-DB-9 console cable

Auxiliary Black Modem for remote access RJ-45-to-DB-9 console cable andDB-9-to-DB-25 adapter

USB Peripheral devices USB cable
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/hw_inst/cabling/marcabl.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/hw_inst/cabling/marcabl.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/hw_inst/cabling/marcabl.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/hw_inst/cabling/marcabl.htm

7/28/2019 1800 Start

14/25

14

Power Connections

Connect the router power cord to a 15A, 120 VAC power source or 10A, 240 VAC power source.

Warning This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that theprotective device is rated not greater than: 15A, 120VAC (10A, 240VAC). Statement 1005

Note The input voltage tolerance limits for AC power are 85 and 264 VAC.

6 Power Up the Router

Checklist for Power Up

You are ready to power up the Cisco 1841 router after the following steps are completed:

Chassis is securely mounted and grounded. (See the Install Chassis section on page 4.)

Power and interface cables are connected. (See the Connecting Cables section on page 12.)

Make sure that the external CompactFlash memory card is properly seated into the slot. For installation instructions, referto the online Cisco 1800 series hardware installation documentation at the following URL:


PC with terminal emulation program is connected to the console port, powered up, and configured for 9600 baud, 8 databits, 1 stop bit, no flow control, and no parity.

Suitable PC COM port is selected in the terminal emulation program.

Note For initial power up, a direct console connection is recommended. After the initial configuration is completed, a remotemodem connection can be used for router management.

Caution To ensure adequate cooling, never operate the router unless the cover and all modules and cover plates are installed

Caution To prevent damage to the ejector mechanism, the ejector button next to the CompactFlash memory card mustremain fully seated when not being used to eject a CompactFlash memory card.

Power-Up Procedure

To power up your Cisco 1841 router and verify that it goes through its initialization and self-test, perform this procedure. When

the procedure is finished, the Cisco 1841 router is ready to configure.

Note To view the boot sequence, you must have a console connection to the Cisco 1841 router before it powers up.

Step 1 Make sure that your PC is powered up and connected as described in the Checklist for Power Up section on page 14

Step 2 Move the power switch to the ON position. The SYS PWR LED on the front of the chassis blinks green and the fansoperate. If this does not happen, refer to the "Troubleshooting" module in the online Cisco 1800 series hardwareinstallation documentation at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/hw/index.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/hw/index.htm

7/28/2019 1800 Start

15/25

15


Startup messages appear in your terminal emulation program window. When the startup messages end, the SYS PWRLED comes on solid green.

Caution Do not press any keys on the keyboard until the messages stop and the SYS PWR LED is solid green . Any keyspressed during this time are interpreted as the first command typed when the messages stop, which might cause therouter to power off and start over. It takes a few minutes for the messages to stop.

You may see different startup messages:

If you see the following messages, the router has booted with a configuration file and is ready for initialconfiguration using Cisco Router and Security Device Manager (SDM):

yourname con0 is now available

Press RETURN to get started.

Note Because SDM is installed on your router by default, we recommend using SDM to perform the initialconfiguration.

If SDM is installed on your router, we recommend using SDM to perform the initial configuration. See the InitialConfiguration Using Cisco Router and Security Device Manager section on page 17 to learn how to configure yourrouter using SDM, or how to obtain SDM and install it on your router.

If you see the following messages, the router has booted and is ready for initial configuration using the setupcommand facility or the command-line interface (CLI):

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes/no]:

To learn how to use the setup command facility to configure the router, see the Initial Configuration Using SetupCommand Facility section on page 17. To learn how to use the CLI to configure the router, see the InitialConfiguration Using Cisco CLIManual Configuration section on page 20.

If the rommon 1> prompt appears, your system has booted in ROM monitor mode. For information on using ROMmonitor, refer to the Troubleshooting and Maintenance module in the online Cisco 1800 series softwareconfiguration documentation at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/sw/index.htm

Verify the Front Panel LED Indications

The indicator LEDs described in Table 3 provide power, activity, and status information.

Table 3 LED Indicators

LED Color Description Location

SYS PWR Green Router has successfully booted up and the software is functional. This LED blinks

while booting or in the ROM monitor.

Front

SYS ACT Green Blinking when any packets are transmitted or received on any WAN or LAN, or when

monitoring system activity.

Front
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/sw/index.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/hw/index.htmhttp://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1800/sw/index.htm

7/28/2019 1800 Start

16/25

16

Verify the Hardware Configuration

Verify the router hardware configuration by entering the following commands:

show versionDisplays the system hardware version; the installed software version; the names and sources of configurationfiles; the boot images; and the amount of installed DRAM, NVRAM, and flash memory.

show diagLists and displays diagnostic information about the installed controllers, interface processors, and portadapters. Typical examples are network modules, interface cards (WICs, VWICs, HWICs) and advanced integrationmodules (AIMs).

7 Interface NumberingEach individual interface (port) on a Cisco 1841 router is identified by a number. A Cisco 1841 router contains the followingwide-area network (WAN) and local-area network (LAN) interface types:

Two onboard Fast Ethernet LAN interfaces

Two slots in which you can install WICs, VWICs (data only), and HWICs

The numbering format for the slots is interface-type 0/slot-number/port-number. Table 4 summarizes the interface numbering.

CF Green On when compact flash memory is busy. Do not remove CompactFlash memory card

when this light is on.

Back

FDX (FE 0) Green On indicates full-duplex operation. Off indicates half-duplex operation. Back

100 (FE 0) Green On indicates a 100-Mbps link. Off indicates a 10-Mbps link. Back Link (FE 0) Green On when the router is correctly connected to a local Ethernet LAN through Ethernet

port 0.

Back

FDX (FE 1) Green On indicates full-duplex operation. Off indicates half-duplex operation. Back

100 (FE 1) Green On indicates a 100-Mbps link. Off indicates a 10-Mbps link. Back

Link (FE 1) Green On when the router is correctly connected to a local Ethernet LAN through Ethernet

port 1.

Back

AIM Green On indicates presence of an AIM in the internal AIM slot. Back

Table 4 Interface Numbering

Slot Number Slot Type Slot Numbering Range Example1

1. The interfaces listed are examples only; other possible interface types are not listed.

Onboard Ports Fast Ethernet 0/0 and 0/1 interface fastethernet 0/0

Slot 0 HWIC/WIC/VWIC2

2. VWICs are data-only in Cisco 1841 routers.

0/0/0 to 0/0/3 interface serial 0/0/0

line async 0/0/0

Slot 1 HWIC/WIC/VWIC

2

0/1/0 to 0/1/3 interface serial 0/1/0line async 0/1/0

Table 3 LED Indicators (continued)

LED Color Description Location

7/28/2019 1800 Start

17/25

17

Note On the Cisco 1841 router, the numbering format for configuring an async interface is 0/slot/port. To configure the lineassociated with an async interface, simply use the interface number to specify the async line. For example, line 0/0/0specifies the line associated with interface serial 0/0/0 on a WIC-2A/S in slot 0. Similarly, line 0/1/1 specifies the lineassociated with interface async 0/1/1 on a WIC-2AM in slot 1.

8 Perform Initial ConfigurationYou can configure your router by using one of the following tools:

Cisco Router and Security Device Manager (SDM)See the Initial Configuration Using Cisco Router and Security DeviceManager section on page 17.

Setup command facilitySee the Initial Configuration Using Setup Command Facility section on page 17.

Command-line interface (CLI)See the Initial Configuration Using Cisco CLIManual Configuration section onpage 20.

Initial Configuration Using Cisco Router and Security Device Manager

If the following messages appear at the end of the startup sequence, Cisco Router and Security Device Manager (SDM) isinstalled on your router:

yourname con0 is now available

Press RETURN to get started.

For instructions on configuring your router by using SDM, refer to the Cisco Router and Security Device Manager (SDM) QuickStart Guide that shipped with your router.

Tip If the messages above do not appear, SDM and the Cisco Router and Security Device Manager (SDM) Quick StartGuide were not shipped with your router. If you want to use SDM, you can download the latest version of SDM andinstructions for installing it on your router from the following location:

http://www.cisco.com/pcgi-bin/tablebuild.pl/sdm

To obtain the SDM quick start guide, SDM release notes, and other SDM documentation, go to www.cisco.com/go/sdmand click the Technical Documentation link.

Initial Configuration Using Setup Command Facility

This section shows how to use the setup command facility to configure a hostname for the router, set passwords, and configurean interface for communication with the management network.

If the following messages appear at the end of the startup sequence, the setup command facility has been invoked automatically






The setup command facility prompts you for basic information about your router and network, and it creates an initialconfiguration file. After the configuration file is created, you can use the CLI or Cisco Router and Security Device Manager toperform additional configuration.
http://www.cisco.com/go/sdmhttp://www.cisco.com/go/sdm

7/28/2019 1800 Start

18/25

18

The prompts in the setup command facility vary, depending on your router model, the installed interface modules, and thesoftware image. The following example and the user entries (in bold) are shown as examples only.

For help with interface and port numbering, see the Interface Numbering section on page 16.

Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again.Press Ctrl-C, and enter the setup command at the privileged EXEC mode prompt (Router#).

Step 1 To proceed using the setup command facility, enter yes:

Would you like to enter the initial configuration dialog? [yes/no]: yes

Step 2 When the following messages appear, enter yes to enter basic management setup:




Basic management setup configures only enough connectivity

for management of the system, extended setup will ask you

to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: yes

Step 3 Enter a hostname for the router (this example uses Router):

Configuring global parameters:

Enter host name [Router]: Router

Step 4 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing theconfiguration:

The enable secret is a password used to protect access to

privileged EXEC and configuration modes. This password, after

entered, becomes encrypted in the configuration.

Enter enable secret: xxxxxx

Step 5 Enter an enable password that is different from the enable secret password. This password is notencrypted (less secure)and can be seen when viewing the configuration:

The enable password is used when you do not specify an

enable secret password, with some older software versions, and

some boot images.

Enter enable password: xxxxxx

Step 6 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than theconsole port:

The virtual terminal password is used to protect

access to the router over a network interface.

Enter virtual terminal password: xxxxxx

Step 7 Respond to the following prompts as appropriate for your network:Configure SNMP Network Management? [yes]:

Community string [public]:

A summary of the available interfaces is displayed.

7/28/2019 1800 Start

19/25

19

Note The interface numbering that appears depends on the type of Cisco modular router platform and on theinstalled interface modules and cards.

Current interface summary

Controller Timeslots D-Channel Configurable modes Status

T1 0/0/0 24 23 pri/channelized Administratively upT1 0/0/1 24 23 pri/channelized Administratively up

T1 0/1/0 24 23 pri/channelized Administratively up

T1 0/1/1 24 23 pri/channelized Administratively up

Any interface listed with OK? value "NO" does not have a valid configuration

Interface IP-Address OK? Method Status Prol

FastEthernet0/0 unassigned NO unset up up

FastEthernet0/1 unassigned NO unset up dow

Step 8 Select one of the available interfaces for connecting the router to the management network:

Enter interface name used to connect to the

management network from the above interface summary: fastethernet0/0

Step 9 Respond to the following prompts as appropriate for your network:Configuring interface FastEthernet0/0:

Use the 100 Base-TX (RJ-45) connector? [yes]: yes

Operate in full-duplex mode? [no]: no

Configure IP on this interface? [yes]: yes

IP address for this interface: 172.1.2.3

Subnet mask for this interface [255.255.0.0] : 255.255.0.0

Class B network is 172.1.0.0, 26 subnet bits; mask is /16

Step 10 The configuration is displayed:

The following configuration command script was created:

hostname Router

enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1

enable password xxxxxxline vty 0 4

password xxxxxx

snmp-server community public

!

no ip routing

!

interface FastEthernet0/0

speed 100

half-duplex

ip address 172.1.2.3 255.255.0.0

!

interface FastEthernet0/1

shutdown

no ip address

end

Step 11 Respond to the following prompts. Select [2] to save the initial configuration.

[0] Go to the IOS command prompt without saving this config.

[1] Return back to the setup without saving this config.

[2] Save this configuration to nvram and exit.

Enter your selection [2]: 2

Building configuration...

Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started! RETURN

7/28/2019 1800 Start

20/25

20

The user prompt is displayed.

Router>

Step 12 Verify the initial configuration. See the Verify the Initial Configuration section on page 21 for verificationprocedures.

Initial Configuration Using Cisco CLIManual Configuration

This section shows how to display a command-line interface (CLI) prompt for configuration using the CLI, and it directs youto documentation for the CLI configuration. You can use the CLI if the following messages appear at the end of the startupsequence:






If these messages do not appear, SDM and a default configuration file were installed on the router at the factory. To use SDMto configure the router, see the Initial Configuration Using Cisco Router and Security Device Manager section on page 17.

For help with interface and port numbering, see the Interface Numbering section on page 16.

Step 1 To proceed with manual configuration using the CLI, enter no when the power-up messages end:

Would you like to enter the initial configuration dialog? [yes/no]: no

Step 2 Press Return to terminate autoinstall and continue with manual configuration:

Would you like to terminate autoinstall? [yes] Return

Several messages appear, ending with a line similar to the following:

Copyright (c) 1986-2004 by Cisco Systems, Inc.

Compiled by

Step 3 Press Return to display the Router> prompt:

...

flashfs[4]: Initialization complete.

Router>

Step 4 Enter privileged EXEC mode:

Router> enable

Router#

Step 5 For configuration procedures, refer to the applicable configuration instructions in the Cisco 2800 series softwareconfiguration documents. See the Where to Go Next section on page 21 for information about accessing thesedocuments.

Note To avoid losing work you have completed, be sure to save your configuration occasionally as you proceed. Usethe copy running-config startup-config command to save the configuration to NVRAM.

Step 6 When you have finished the initial configuration, verify the initial configuration. See the Verify the InitialConfiguration section on page 21 for verification procedures.

7/28/2019 1800 Start

21/25

21

Verify the Initial Configuration

To verify that the new interfaces are operating correctly, perform the following tests:

To verify that the interfaces are operating correctly and that the interfaces and line protocol are in the correct stateup ordownenter the show interfaces command.

To display a summary status of the interfaces configured for IP, enter the show ip interface briefcommand.

To verify that you configured the correct host name and password, enter the show configuration command.When you complete and verify the initial configuration, your Cisco router is ready to configure for specific functions. See theWhere to Go Next section on page 21 for information about locating documentation for advanced configuration procedures

9 Where to Go NextFor additional configuration procedures, refer to the appropriate Cisco 1800 series routers documentation or Cisco IOSsoftware documentation, available online on Cisco.com.

Tip See the Obtaining Documentation section on page 21 for help in locating these documents.

To access documentation on Cisco.com

For Cisco 1841 router platform documentation, begin at Cisco.com at http://www.cisco.com , and select Products & Solutions >Routers > 1800 Series Integrated Services Routers> Technical Documentation > Document type > Document.

For Cisco IOS software documentation, start on Cisco.com at http://www.cisco.com , and select Products & Solutions > IOSSoftware > Cisco IOS Software Releases > Your Cisco IOS software release.

To get updated information about platform support for features, access Feature Navigator II at http://www.cisco.com/go/fn.(Requires a registered account on Cisco.com.)

To access documentation using Cisco Connection Online (CCO):

For Cisco 1800 series routers platform documentation, start on Cisco.com at http://www.cisco.com , and click the TechnicalDocumentation tab under Quick Links. Under the Product Documentation heading, navigate to Modular Access Routers andto the documentation for your router.

For Cisco IOS software documentation, start on Cisco.com at http://www.cisco.com , and click the Technical Documentationtab under Quick Links. Under the Product Documentation heading, navigate to the Cisco IOS software documentation for theCisco IOS software release that is installed on your router.

10 Obtaining DocumentationCisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technicalassistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml
http://www.cisco.com/go/fnhttp://www.cisco.com/go/fnhttp://www.cisco.com/go/fnhttp://www.cisco.com/univercd/home/home.htmhttp://www.cisco.com/http://www.cisco.com/public/countries_languages.shtmlhttp://www.cisco.com/go/fnhttp://www.cisco.com/go/fnhttp://www.cisco.com/go/fnhttp://www.cisco.com/go/fnhttp://www.cisco.com/public/countries_languages.shtmlhttp://www.cisco.com/http://www.cisco.com/univercd/home/home.htm

7/28/2019 1800 Start

22/25

22

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool:

http://www.cisco.com/en/US/partner/ordering/index.shtml

Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco SystemsCorporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS(6387).

11 Documentation FeedbackYou can send comments about technical documentation to [email protected].

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to thefollowing address:

Cisco Systems

Attn: Customer Document Ordering170 West Tasman DriveSan Jose, CA 95134-9883

We appreciate your comments.

12 Obtaining Technical AssistanceFor all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensiveonline support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you donot hold a valid Cisco service contract, contact your reseller.

Cisco Technical Support Website

The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issueswith Cisco products and technologies. The website is available 24 hours a day, 365 days a year at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid servicecontract but do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests arethose in which your network is minimally impaired or for which you require product information.) After you describe yoursituation, the TAC Service Request Tool automatically provides recommended solutions. If your issue is not resolved using therecommended resources, your service request will be assigned to a Cisco TAC engineer. The TAC Service Request Tool is locatedat this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requestsare those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately toS1 and S2 service requests to help keep your business operations running smoothly.
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htmhttp://www.cisco.com/en/US/partner/ordering/index.shtmlhttp://www.cisco.com/techsupporthttp://tools.cisco.com/RPF/register/register.dohttp://www.cisco.com/techsupport/servicerequesthttp://www.cisco.com/techsupport/servicerequesthttp://tools.cisco.com/RPF/register/register.dohttp://www.cisco.com/techsupporthttp://www.cisco.com/en/US/partner/ordering/index.shtmlhttp://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

7/28/2019 1800 Start

23/25

23

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)EMEA: +32 2 704 55 55USA: 1 800 553 2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)Your network is down, or there is a critical impact to your business operations. You and Cisco will commitall necessary resources around the clock to resolve the situation.

Severity 2 (S2)Operation of an existing network is severely degraded, or significant aspects of your business operation arenegatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normalbusiness hours to resolve the situation.

Severity 3 (S3)Operational performance of your network is impaired, but most business operations remain functional. Youand Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)You require information or assistance with Cisco product capabilities, installation, or configuration. There islittle or no effect on your business operations.

13 Obtaining Additional Publications and InformationInformation about Cisco products, technologies, and network solutions is available from various online and printed sources.

Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, thecompany store, at this URL:

http://www.cisco.com/go/marketplace/

The Cisco Product Catalogdescribes the networking products offered by Cisco Systems, as well as ordering and customersupport services. Access the Cisco Product Catalog at this URL:

http://cisco.com/univercd/cc/td/doc/pcat/ Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users

will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:

http://www.ciscopress.com

Packetmagazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Eachquarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions,as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification andtraining information, and links to scores of in-depth online resources. You can access Packet magazine at this URL:

http://www.cisco.com/packet

iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can usetechnology to increase revenue, streamline their business, and expand services. The publication identifies the challengesfacing these companies and the technologies to help solve them, using real-world case studies and business strategies to help

readers make sound technology investment decisions. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

Internet Protocol Journalis a quarterly journal published by Cisco Systems for engineering professionals involved indesigning, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journalat this URL:

http://www.cisco.com/ipj

World-class networking training is available from Cisco. You can view current offerings at this URL:

http://www.cisco.com/en/US/learning/index.html
http://www.cisco.com/techsupport/contactshttp://www.cisco.com/go/marketplace/http://cisco.com/univercd/cc/td/doc/pcat/http://www.ciscopress.com/http://www.cisco.com/packethttp://www.cisco.com/go/iqmagazinehttp://www.cisco.com/ipjhttp://www.cisco.com/en/US/learning/index.htmlhttp://www.cisco.com/en/US/learning/index.htmlhttp://www.cisco.com/ipjhttp://www.cisco.com/go/iqmagazinehttp://www.cisco.com/packethttp://www.ciscopress.com/http://cisco.com/univercd/cc/td/doc/pcat/http://www.cisco.com/go/marketplace/http://www.cisco.com/techsupport/contacts

7/28/2019 1800 Start

24/25

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000

800 553-NETS (6387)Fax: 408 526-4100

European HeadquartersCisco Systems International BVHaarlerbergparkHaarlerbergweg 13-191101 CH AmsterdamThe Netherlandswww-europe.cisco.comTel: 31 0 20 357 1000Fax: 31 0 20 357 1100

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-7660Fax: 408 527-0883

Asia Pacific HeadquartersCisco Systems, Inc.168 Robinson Road#28-01 Capital TowerSingapore 068912www.cisco.comTel: +65 6317 7777Fax: +65 6317 7799

Cisco Systems has more than 200 offices in the following countries. Addresses, phone numbers, and fax numbers are listed on the

C i s c o W e b s i t e a t w w w . c i s c o . c o m / g o / o f f i c es

Argentina Australia Austria Belgium Brazil Bulgaria Canada Chile China PRC Colombia Costa Rica Croatia Cyprus Czech Republic DenmarkDubai, UAE Finland France Germany Greece Hong Kong SAR Hungary India Indonesia Ireland Israel Italy Japan Korea Luxembourg MalaysiaMexico The Netherlands New Zealand Norway Peru Philippines Poland Portugal Puerto Rico Romania Russia Saudi Arabia Scotland SingaporeSlovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Thailand Turkey Ukraine United Kingdom United States Venezuela VietnamZimbabwe

Printed in the USA on recycled paper containing 10% postconsumer waste.

78-15495-04

DOC-7815495=

CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access RegistrarAironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logoCisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ NetReadiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way tIncrease Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates i n the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.(0711R)

7/28/2019 1800 Start

25/25

1800 Start

Documents

Transcript of 1800 Start