1358-SERIES Electrically Operated Plastic Ball Valve Technical Specifications

Data Sheet Ref. No : SU-1358-00002

SUDE PUNE / BANGALORE

MODEL NO.:

1358\50\PVC\PVC\T\ONF\BSP\SD-

1000-05\2LS Quotation Ref. No

Quotation Date 1. ITEM ASSEMBLY OF 2 WAY PLASTIC BALL VALVE FITTED

WITH SINGLE PHASE QUARTER TURN ELECTRIC

ACTUATOR 2. MAKE SUDE 3 APPLICATION 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 50mm

End connection BSP Screwed

Body Material PVC

Ball Material PVC

Seating material Teflon

Flowing medium Acid

Pressure 10 Bar

Temperature Ambient

Characteristic On/Off Type

Fitted with

Sdtork Make Single Phase Quarter Turn Electric Actuator Supply Voltage 230 V AC.

ACTUATOR DETAILS 3.1 Model SD-1000-05 3.2 Output motion type 3.3 Output Torque ( Nm ) 3.4 Output speed ( Sec/90 °) 3.5 Manual hand wheel PROVIDED 3.6 Travel limit switches

2 Nos Type : 1 NO + 1 NC, change over contact, contact rating: 5 A, 230 V AC

3.7 Torque limit switches Not required, AS 1000-series actuator are provided with stall duty motor

3.8 Local indicator PROVIDED 3.9 Class of Protection IP67 3.10 Weight of the actuator (Kgs.) 3.11 Duty 3.12 Mounting 3.14 G. A. Drawing Reference No 3.15 Electrical Wiring Diagram Ref, No 3.16 Weight of Actuator – Kgs MOTOR DETAILS 4.1 Type Reversible Single Phase Synchronous Stall Duty Motor 4.2 Supply 230 V +/- 10 %, 50 Hz +/- 5 % AC Supply 4.3 Duty S2-10 min / S-4-30 % 1200 Cycles/ hr. 4.4 Insulation Class F 4.5 Rating ( Watts) OPTIONAL ACCESSORIES

5.1

Feedback Potentiometer

Out put : 100-235 Ohms Not Provided

5.2

Additional Limit Switches

Qty : 2 nos. Type : 1 NO + 1 NC, Change over contact, Contact rating: 5 A, 230VAC

Provided

5.3

Two Wire Transmitter Type : Two wire, Actuator mounted Supply : 12-36 VDC, Output : 4-20 m A

Not Provided

5.4

Remote Position indicator

Available in servo controller Digital : 0-100 %

Not Provided

5.5

Servo controller (Valve positioner) Panel Mounted

Input signal : 4-20 m A, Output : 4-20 m A Feed back : 0-500 Ohms, supply 230 V AC, This will have auto calibration facility.

Not Provided

5.6 Interface Card Actuator Mounted

Input signal : 4-20 m A, Feed back : 100-235 Ohms,

Not Provided

5.6 Control Panel

This will consist of 2 nos. of Control Relay with required control voltage (If not specify, control voltage will be 230 VAC ) Auto / Manual selector switch, Open/Close push buttons, emergency stop button & MCB.

Not Provided

5.7 Local Push Button Station

This will consist of Auto /Off / Manual selector switch, Open/Close push buttons.

Not Provided

6 GENERAL POINTS 6.1 Inspection By Customer at our works

6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of installation

which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box

SPECIAL NOTE :