1268 plastic butterfly & ball valves with actuator

N

I

C

H

G

F

E

12

15

14

685 MAX

485Ø 50

A

440

D

C

n Øe

B

8

G

7

A

F

B

C

K

M

L

12

10, 11

13, 14, 15

9

I

J

N

I

C

H

G

F

E

12

15

14

685 MAX

485Ø 50

A

440

D

C

n Øe

B

8

G

7

A

F

B

C

K

M

L

12

10, 11

13, 14, 15

9

I

J

Plastic Butterfly and Ball Valves

Fitted with Pneumatic / Electric Actuator

1258/1268SERIES

1358/1368SERIES

SUDER

Yes. We ARE...| ourteously | ttentively | espectably | ffectively | C A R E

An ISO 9001:2008 Certified Company

CAT# 15 / QTY: 500 PAGES: 28 (4+24) CLR : Special Blue + BLACK

Plastic Butterfly And Ball Valves

Fitted With Pneumatic And Electric Actuator

Sude Offers Plastic Butterfly Valves available in two types or styles, wafer

and lug. A different installation procedure is used for each one. Wafer

Style is the more common of the two and is less expensive than the lug

style. The wafer style butterfly valve is just about the standard. (Refer

figure No.1). Wafer butterfly valves are installed between two flanges

using bolts or studs and nuts. This type of installation of course, makes it

impossible to disconnect just one side of the piping system from the

valve. That is where the lug style valve comes in.

Lug style valves have metal inserts installed in the valve's bolt holes.

These inserts are threaded on both ends. This allows them to be installed

into a system using two sets of bolts and No nuts. The valve is installed

between two flanges using a separate set of bolts for each flange. This

permits either side of the piping system to be disconnected without

distributing the other side.

Lug style butterfly valves used in dead end service generally have a

reduced pressure rating. For example most sizes of butterfly valves

mounted between two flanges have a 150psi pressure rating. The same

valve mounted with on flange in dead end service has a 75 psi rating.

Thermoplastic butterfly valves that are slip in wafer style, compact design,

light in weight and easy to install. They are available in size range of

50mm to 400mm, 500 & 600mm available on request.

Sude supply Plastic Butterfly Valves which are made from light quality

thermoplastic like PP, HDPE-High density Polyethylene and PVDF -

Polyvinylidene Fluoride. The valves are tight shut off in both flow

directions and recommended for pressure rating of PN10.

These valves offer square section shaft that provide positive engagement

between shaft and disc and shaft & lever ensuring positive shut off with

quarter turn operation. They are suitable for flow in either directions or

can be utilized either vertically or horizontally. The valve disc fitted with

seat ring is easily replaceable as well as economical compare to

conventional rubber liner. They are also available with double-flanged end

connections. The butterfly valves are available having flange with

drilling as per BS, ASA, DIN or any other standard.

Introduction - Butterfly ValvesIndexIntroduction - Butterfly Valves .................

Elastomer Seated Butterfly Valves ............

Operating & Maintenance Guide

Butterfly Valves .........................................

Universal Design Advantages ..................

Ball Valves .................................................

3 Way Ball Valves ......................................

Pneumatic Actuator ...................................

Electrical Actuator ......................................

Control Panel Specification .......................

GA Drawings .............................................

01

07

07

08

10

11

13

14

15

03

SUDE01 1258/1268 & 1358/1368 SERIES


Butterfly valves offered with PVC & CPVC thermoplastic construction for corrosion resistance in chemical and wastewater

applications. One-piece body incorporates fully supported flanged bolt holes to prevent stressing of mating pipe flanges

and full body liner with v-notch retention design ensures positive sealing of EPDM or Nitrile to valve body. Valves will not

contaminate sensitive fluids

Sude offers a plastic Butterfly valve having a reinforcement blade which includes a valve body of plastic material, having

two separately positioned openings for connection in a pipeline: and a blade which is also constructed substantially from

plastic material. The blade is journeyed in the housing so as to be rotable to a position wherein it prevents fluid flow

between the openings in the housing

1

1

1

1

1

4

2

1

1

2

1

Body

Engagement disc

Bearing bush

Bearing bush

Shaft

Round sealing rings

Round sealing rings

sealing element (stirrup)

Disk ring

Locking ring

closing cap

1

2

3

4

5

6

7

8

9

10

11

Item Qty. Parts

1

1

1

2

1

4

2

4

Body

Butterfly disc

Shaft

Round sealing rings

Sealing element

Screws

Locking ring

Washer

1

2

3

4

5

6

7

8

Item Qty. Parts

Fig.1: Typical Exploded View of the Butterfly Valve

9

10

5

3

6

9

1

6

4

1011

78

6

2

6

7

3

3

8

6

4

1

2

4

02SUDE 1258/1268 & 1358/1368 SERIES

5


Elastomer Seated Butterfly Valves :

Elastomer seated butterfly valves are available up to 24”. The designed incorporates molded body gussets to prevent over

tightening of the seat, a redesigned spherical disc for better sealing and increased Cv values. It maintains the features of

the type standardized actuator mounting.. These valves offer a large range of sizes and selection of body, disc and seat

materials. This allows them into a wide range of on/off or throttling control applications.(Refer Figure No.2)

Moulded Elastomer Seat

Easily replaceable

Flange face has ralsed "O-ring" profile

- Low flange bolt torques to seal

Three ribs lock into body

- Long term stability even under vacuum

Special Sealing Design

Seals and disc have spherical

Sealing surfaces

- Lower stem torques to seal

- Longer seat life compared

to conventional designs.

Non- wetted Stainless Steel Retaining Ring

Provides for effective stem sealing

at all working pressures.

Shaft O-Ring

For vacuum resistance

Stainless Steel Shaft

Not wetted

Engagement over full length of the disc

Streamlined Disc

High Cv values

Good flow characteristics.

Important for control

applications.

SIZES : 1” to 24”

BODY TYPE : Semi lug wafer1

BODY : PVC, PP, PVDF

DISC : PP, PVC, PVDF

SEAT AND O-RINGS : EPDM, VITON

Fig. 2 : Wetted parts of the Butterfly valves

SUDE03 1258/1268 & 1358/1368 SERIES


Fig. 3 : Temperature/Pressure Characteristics ofDifferent Plastic Valves

Features :

?Compact and Light Weight

?High Corrosion Resistance

?Solid plastic body-no rust

?Rated at 150 PSI and Temperature Up to 0120 C (Refer Figure 3)

?Stainless Steel Shaft

?Fully Supported Flange Bolt Holes

?Full Body, V-Notch Liner

?Blowout-Proof Shaft

?Viton, EPDM OR Nitrile Liners

?Wafer Body Design

Seat over Tightening Protection

Molded body gaskets prevents over tightening of seat

Increased Cv

Spherical disc design offers increased Cv better sealing and higher cycle life(Refer figure 4)

Fig. 4 : Pressure v/s Flow graph for Different size of butterfly valve

oPressure loss curve (reference values for H O, 20 C For Butterfly Valve2

flow Q (l/min)

pre

ss

ure

lo

ss

p (

ba

r)?

kv (I/min) =

1,000

0,100

0,050

0,010

0,005

0,001

100 1,000 10,000 10,000 500,000

1,460 3,350 11,060 39,150 80,000 40,000 240,000

2,050 6200 15650 55000 100000 180000 310000

DN 50

DN 50

DN 65

DN 65

DN 80

DN 80

DN 100

DN 100

DN 125

DN 125

DN 150

DN 150

DN 200

DN 200

DN 250

DN 250

DN 300

DN 300

DN 350

DN 350

DN 400

DN 400

DN 450

DN 450

DN 500

DN 500

DN 600

DN 600

Pressure loss and K valuev

The diagram shows pressure loss p in relation to the flow Q.

For Calculation :

C = K x 0,007v v

Units :

K [l/min]v

C [gal/min] USv

04SUDE 1258/1268 & 1358/1368 SERIES


Abrasion Resistant

ISO Actuator mounting dimensions

Easily Installed

Easily Maintained

?Solid plastic disc

?PVDF disc available for high abrasion resistance

?Top flange and shaft have standard ISO dimensions for

easy actuator mounting

?Full bolt hole circle makes installation and alignment easy

?No gaskets are necessary

?Full bolt hole circle makes installation and alignment easy

Refer(Figure No.5)

?No gaskets are necessary Seat is easily replaceable

Fig. 5 : Typical Installation OfButterfly Valves

Full Blot Circle for easy installationGussets on body prevents over compression of valve seat.

Elastomer Seat with Stainless Retaining Ring

Shaft O-Ring

Stainless Steel Shaft

?Easily replaceable

?Flange face has raised “O-ring” profile

?Lower flange bolt torques required for a leak proof

seal

?For vacuum resistance

?Not wetted

?Engagement Over full length of the disc

Solid Plastic Disc

Double O-Rings at top and bottom of disc

Options & Accessories:

?No disc screws

?Abrasion resistant

?No problems as associated with coatings or

linings.

?Provide a primary and secondary seal between

seat and disc Shaft is not wetted

?Alternate Elastomer Seats Viton

?Alternate Discs PVC, CPVC, PVDF

?Electric or Pneumatically Actuated

?Municipal Operating Nut for buried service

?Chain Wheel Operator

?Shaft Extensions

?Lug Body Inserts Stainless steel lugs for dead

end service

Sude offers Plastic Butterfly valve which has a one

piece body that incorporates fully supported flanged bolt

holes to prevent stressing of the mating pipe flanges.

Their heavy duty construction stands up to the most

demanding applications. The rock solid integral

mounting pad insures the correct assembly with

Actuator.

Butterfly Valves feature a blowout-proof stainless steel

stem and unique, full body liner that has a V-notch

retention design. This assures positive sealing of the

liner to the valve body. An integrally molded face seal

provides positive sealing against the mating flange

without the need for additional gaskets.

Tight Sealing

Other plastic butterfly valves have only a thin o-ring on

the disk to seal the valve, but Sude offers valves which

feature a full body liner seal. This means that the

process media never contacts the valve body. And you

can count on the full liner seal to perform reliably, year

after year.

Easy Retrofit

Sude offers Butterfly Valves having ISO pad which

make the retrofit very easy at site.

SUDE05 1258/1268 & 1358/1368 SERIES


No Metal, No corrosion

These valves have no metal in contact with the process

media. They cannot corrode or rust nor will they

contaminated sensitive fluids flowing through them.

Application

Plastic Butterfly valves are used in Water Distribution,

Chemical Services and Ventilation Applications.

Other Materials Available Upon Request.

End Connections

Socket

Provides a stronger connection than threading and is a

permanent installation.

Solvent Cemented

Compatible with PVC and CPVC Valves, using normal

solvent cementing techniques. Caution should be taken

that cement does not get on the inside face of the end

connection or inside the valves. Refer to cement

manufacturer's guidelines for bonding temperature

limitations and recommended connecting care times.

NOTE: Shelf life of solvent cement is limited to the time

advised by the manufacturer. That is approximately one

year for CPVC and two years for PVC.

Connections:

Socket Fusion Thermal Bonding:

The superb resistance of PVDF and PP to organic

solvents including solvent cements makes it necessary

to join those socket connections in ½“through 4” sizes

by thermal bonding technique.

Thermal Bonding:

A heat fusion technique necessary for joining PVDF and

PP butt end connections to similar materials piping.

Threaded :

Preferred when occasional disconnection of piping

system is necessary but limited to a maximum 4 inches

in diameter. Thermoplastic pipe of Schedule 80 or

heavier should be used because threading reduces the

effective wall thickness, resulting in a reduction in

pressure rating to one-half that of solvent cemented or

thermal bonded socket connections. Threads are

American Standard Tapered Pipe Threads.

Preparation for assembly consists of wrapping the pipe

threads with Teflon (TFE) tape starting the second

thread from the end and wrapping in the direction of

threads, with a slight overlap. After a hand tight

assembly an additional ½ to 1 ½ turns with a strap

wrench will complete the connection. Care must be

taken to not over- tighten which can cause distortion or

even failure of threads.

Flanged :

Manufactured to ANSI B16.5 (150 class). Available in

most all sizes and most widely used throughout the

industry for process system that require occasional

dismantling. Thermoplastic flanges may be connected

to pipe or fitting by the method required by the individual

material.

Joining Flanges :

?Carefully observe for proper alignment of bolt holes

and also for parallelity and closeness of mating

flanges.

?First position the gasket seal. Then inset and lubricate

all bolts using flat washers under bolt heads and nut.

?With a wrench on bolt head, tighten each nut with a

torque wrench in pattern diametrically opposite each

other as shown below (refer figure 6). Do this in

increments until finally reaching recommended torque

valves charted at right.

Butterfly valve should always be installed between two

pipe flanges and never with a gasket seal. The outer

rim of the electrometric valve seal acts as the gasket

seal.

FLANGE SIZE

(IN)

½ “ 1- ½“

2-4

5-8

10

12

14-24

RECOMMENDED

TORQUE (FT-LBS)

10-15

20-30

30-45

50-75

80-110

100

Tightening Pattern For Flange Bolts :

15

3

7

26

4

8Fig. 6 :

06SUDE 1258/1268 & 1358/1368 SERIES


Operating & Maintenance Guide - Butterfly Valves

Operation:

Maintenance:

The Butterfly valves are operated with the actuators either pneumatically or electrically and they are operated in On/Off or

Regulating mode construction.

No maintenance required. If valve is to be stored for any length of time, it should be stored in dark and cool condition to

lengthen the shelf life of the full faced electrometric liner seat. Also in outside pipe lines exposed to sun light precautions

should be taken to eliminate valve failures. Expansion joints in the pipe line are necessary to combat pipe expansion

causing crushing and fracturing the flanged portion of the full faced electrometric liner. This will push the rubber into the

seating area and bind the operation of the valve. If an outdoor pipe line subject to direct sun light is not normally conveying

flow materials the heat can deteriorate the electrometric liner and shorten life of valve seat.

Universal Design Advantages

?Easier installation due to narrow face to face affords

lowest installed cost compared to other valve types

?Designed to fit between ANSI D-16.5 Class 150 flat

faced flanges.

?Strong one piece molded body design

?One piece standard S.S. through shaft for positive disc

rotation and support.

0?Standard polypropylene (PP) disc for higher (180 F)

temperature service.

?Full body liner seat with integral flanges (eliminates the

need for flange gaskets) ribbed for positive flange

seating with minimum required torque

?Standard PVC body and S.S. shaft are effectively

isolated from the flow media by the full liner seat.

?Standard S.S., Carbon steel plated or epoxy coated

external hardware for added corrosion resistance

?Electric and Pneumatic actuation packages available.

?Stem Extensions, Universal joints floor stands available

in verity of materials.

Design SpecificationThermoplastic Butterfly valves 2” to 8” are wafer style to fit

between ANSI B16.5 class 150 flanges. Disc is contoured

for lowest possible drop (highest CV). Shaft is 410 S.S.

and of one piece through shaft design, with square drive

through entire length of blade. Seat liners shall be full

faced with integral ribbed flanges. No auxiliary gaskets

shall be required or for installation. Seat liners shall

effectively isolate the body and shaft for the flow media.

Seat liners shall also thermally insulate the body from the

internal operating temperature. Valve liner and seals are

replaceable. Materials of construction will be decided

based on the process demand.

Not recommended for compressed air or gas service.

SUDE07 1258/1268 & 1358/1368 SERIES


Ball Valves

Sude offers cost sensitive application plastic ball valve which is perfect for applications that require a reliable ball valve at

an economical price. The plastic valve has been designed and tested to make it certain to perform year in and year out in

the most demanding applications without leakage or failure. The internal components of a plastic valve are completely

encapsulated within the valve body in a one step manufacturing process. There is absolutely do danger of leakage through

assembled parts. This also means that the valve never requires adjustment since all internal the one-piece valve body. The

plastic valve is ready to be put into service right out of the box (Refer Figure No. 7)

Fig. 7 : Constructional exploded view of typical Plastic Ball valve.

3

8

6 5 9 4 10 7 2 7 10 1 11 5 6

GENERAL MATERIAL OF CONSTRUCTION

Temperature and Pressure: Pressure rating for both PVC and CPVC is 175 PSI at 75 degrees F (24 C). Maximum temperature for PVC is 140 degrees

F (60 C): maximum temperature for CPVC is 180 degrees F (82C) (Refer figure no 7 & 8)

Fig. 8 : Material Guideline for Pressure & Temperature

PP & PVDF

230

205

175

150

120

90

60

30

Wo

rkin

g P

ress

ure

(P

SI)

0Working Temperature ( F)

-40 -4 32 68 104 140 176 212 248 284

230

205

175

150

120

90

60

30

Wo

rkin

g P

res

su

re (

PS

I)

0Working Temperature ( F)

-40 -4 32 68 104 140 176 212 248 284

PVC & CPVC

08SUDE 1258/1268 & 1358/1368 SERIES

Sl. No. Qty. Parts

1

2

3

4

5

6

1

1

1

1

2

2

Housing/Body

Ball

Shaft

Threaded end bush

Insert

Union

PVC, PP, CPVC, PVDF

PVC, PP, CPVC, PVDF

PVC or Stainless steel

PVC, PP, CPVC, PVDF

PVC, PP, CPVC, PVDF

PVC, PP, CPVC, PVDF

Material Sl. No. Qty. Parts

7

8

9

10

11

2

2

1

2

1

Ball seat

O-ring (shaft)

O-ring (union)

O-ring (Ball seat)

O-ring (union)

Teflon

NITRILE,EPDM ,VITON

NITRILE, EPDM ,VITON

NITRILE EPDM ,VITON

NITRILE EPDM ,VITON

Material


0 20 40 60 80

PN16

14

12

PN10

8

6

4

2

0

-40 -20 100 120 140

PPPVC-U

Pre

ss

ure

(b

ar)

0Temperature ( C)

Fig. 9. : Pressure / Temperature diagram

Ball Valve Features:

Lightweight and Compact

Can't Rust, Won't Corrode

Features

?Long cycle life with Trunnion design-valve mounts in

either direction with no danger of ball “blow put”.

?Dual Shaft seals eliminate leakage

?Reinforced actuating shaft (or stem)

?True union ends-socket or threaded. Flanges, optional

?Self-compensation PTFE seats

?Perfectly round and highly polished ball

?Rugged construction known as “ The Engineered Ball

Valve”

?Rated at a Full 150 PSI

?PTFE Seats

?EPDM Seals

?No internal Parts to Replace

?Easy ¼-Turn Operation

?Socket or Threaded Pipe Connections

Plastic low cost ball valves are designed to fit into

spaces too small for other valves. They are about 1/3

the overall size of a plastic true union valve and they

weigh an average of 50% less. This makes the ideal for

skid-mounted and other application where space and

weight are critical considerations.

All plastic construction means they will never fail stick or

jam because of rusted or corroded parts. And they'll

work in places and environments where metals valves

must be painted or coated just to survive

Design Specifications

Design Advantages

Plastic Ball Valves ½” to 4” are designed to safely block

full system pressure in either direction to allow on-line

system maintenance. Valve stem is of the blow-out Proof

design. Valve has full port for lowest possible pressure

loss. Seats shall be easily adjustable and replaceable.

Stem has an internal pressure sealed land to protect stem

and stem seal from contaminants. Every valve is fully

pressure and cycle tested before leaving the factory.

Materials of construction shall be selected based on

service.

SEAT

?Safely blocks in both upstream and downstream

direction for simple easy, safe system maintenance.

?Double union design permits quick, easy piping system

installation, removal maintenance

?Stem has internal land above ball that is pressure seated

to the body protecting the stem and the stem seal from

contaminants in the fluid media

?Long life self lubricated TFE seats are externally

adjustable, fully replaceable

?True full port design has immeasurable pressure drop

?Safety design blow-out proof stem

?Available in socket, threaded or flanged (ANSI B16.5

class 150) end configurations.

?All valves are hydrostatically tested

?Available stem extensions, 2” square nut operation.

?PTFE(Poly tetra flouro ethylene)

SUDE09 1258/1268 & 1358/1368 SERIES


Features of 3 way Ball valve:?Rugged plastic construction for corrosive atmospheres

?Simple connections for remote operation and position

indication

?All three ports are true union for cost, installation time

and space savings

?Pressure rated to 230 psi

?Provides a high factor of safety

?Integrally molded mounting saddle

?PTFE seals and Seats

?True Union end connection

Flow Patterns

Three-Way Ball Valves come standard with a two port 0ball allowing for three flow configuration within 180 of

rotation. With the bottom Port as the inlet, the flow can be

directed out the left port or out the right port, or shutoff.

Actuated Three-Way Ball Valves come standard with a

three port ball also i.e. Allowing of two flow configurations 0within 90 of rotation.

With the bottom port as the inlet, the flow can be directed

out the left port and right port there is no shutoff position.

An optional ball used with actuated valves, allows flow

through all ports at the same time or flow shutoff (Refer

figure no 10)

Position - 1 Position - 2

Position - 3 Position - 4

Fig. 10

No Metal, No Corrosion

Solid Actuator Mounting Design

Base mounting Pad

Full Port

Fully Blocking

Double Stem O-Rings for Safety

Teflon R Seats have

Elastomer Cushions

Plastic Three way valves contain no metal parts. The

valves will never fail because of corrosion and they do not

require painting or epoxy coating to stand up to aggressive

environments.

A manual valve can be easily automated. Just remove the

handle and install the Actuator /Mounting kit. The

mounting saddle is integrally molded into the valve body.

For rock-solid actuator mounting the valve incorporates a

unique design where by the mounting bracket mounts

directly to the valve body. This assures proper alignment

of the actuator to the valve without creating any damaging

side loads to cause premature stem seal failure.

High capacity and low pressure drops

Downstream union nut may be safely disassembled for

piping maintenance while valve is closed off under full

system pressure.

Upper O-ring groove is deeper than lower. In case of

excessive stem torque stem will shear at the upper grove,

leaving the inner o-ring intact to seal against full line

pressure

?Permits actuated valves to be securely anchored

?Valves may be used as fixation points in the piping

system

?Improved Sealing while lowering stem torques

?Self adjusts for seat wear

10SUDE 1258/1268 & 1358/1368 SERIES

3 Way Ball Valves


DN

10

DN

10

DN

15

DN

15

DN

20

DN

20

DN

25

DN

25

DN

32

DN

32

DN

40

DN

40

DN

50

DN

50

DN

65

DN

65

k (l/min) =v 75 360 1.100 3.200190 740 1.700 4.500

1,000

0,100

0,050

0,010

0,005

0,00110 20 30 50 100 200 500 1.000 5.000

1,000

0,100

0,050

0,010

0,005

0,001100 1.000 10.000 50.000

0,500

7.110 26.8305.100 17.860

DN

65

DN

65

DN

80

DN

80

DN

100

, DN

125

DN

100

, DN

125

DN

150

DN

150

k (l/min)v

Fig 11: Pressure v/s Flow graph for Different size of Ball valve

0Pressure loss curve (reference values for H2O, 20 C) For Ball valve

For Calculation :

C = K x 0,07v v

Units :

K [1/min], C [gal/min]v v

Actuator Construction

Air Pressure Requirement :

2 2a) For Double Acting Actuator - 3.5 kg / cm (Minimum) & 8.5kg / cm (Maximum)

2 2b) For Spring Return Actuator - 4.0 kg / cm (Minimum) & 8.5 kg / cm (Maximum)

The piston incorporates racks and end covers are die casted in aluminum alloy. Barrel is extruded. aluminium alloy hardened

and treated, further finished with deep anodized process to form a protective layer to resist atmospheric corrosion. The

actuators are also available in stainless steel 316 & Nylon plastic construction for food grade and chemical industries

application. The internal materials of the aluminum, SS316 & Nylon plastic actuator are having pinion which is made up of steel,

precision cut, heat treated and ground & also has a high grade of synthetic seals. The actuators before assembly is lubricated

with high temperature resistant smooth grease. The actuators are with compact design operates through 90 degree angle of

actuation. The Actuator is also available in 180 degree rotation.

Pneumatic actuators are available in rotary construction in Double and spring return in on/off and modulating duty format.

Actuators will be inherently failed safe but fail position (open or closed) should be noted. Pneumatic actuators are supplied with

Electro pneumatic positioners which work on continuous pressurized air of 60psi and input signal of 4 to 20 mA with feed back

4 to 20 mA For details refer Actuator catalogue.

Pneumatic Actuator

However Air Pressure Requirement is much dependent on size of the valve, working pressure, quality of Butterfly valve and

many other factors.

pre

ss

ure

lo

ss

p

(b

ar)

?

pre

ss

ure

lo

ss

p

(b

ar)

?

Flow Q (l/min) Flow Q (l/min)

SUDE11 1258/1268 & 1358/1368 SERIES


Accessories

Accessory Common for Double Acting / Spring Return Actuator :

a) Pressure Regulator

b) Limit Switches

c) Filter Regulator with Lubricator

d) Gear Box with hand wheel for manual operation

e) Valve Positioner for characteristic controlled application.

f) I to P Converter.

g) Electro pneumatic positioners

h) Position Indicator

i) Position Transmitter

j) Cyclic Timer OR Sequential Timer

k) 3 Way / 4 Way Key operated valves

l) Stimulator

m) Travel Stops

n) Flow Restricter

o) Silencers with Flow Control Valve

Optional :

a) PID Controller along with PT - 100 sensor supplied with panel.

b) Pressure Transmitter supplied with panel.

Tests

The valves are tested according to their respective standards for hydrostatic, seat leakage and working pressure tests.

Unless and otherwise specified Ball valves are Constructed and tested for10 kg/cm2 working pressure

Notes :

2a) Actuator rating is for valve working pressure 10 kg / cm

b) Timing given is approximate and is useful as an indicating figure only when solenoid valve is directly coupled with

the Actuator. Average time under 50% load condition is 80 PSI working pressure.

c) All data is complied in laboratory test, in actual field, working may differ.

d) Width and weight will change with rating of flanges and accessories. (Refer GA Drawings)

For Double Acting Actuator:

4 way 5 port single Coil / Double Coil solenoid valve in general purpose or Flame proof and explosion coils construction.

For Spring Return Actuator:

3 way Single Coil / Double Coil solenoid valve in General purpose or Flame proof and explosion Coils construction.

12SUDE 1258/1268 & 1358/1368 SERIES


Electrical Actuator

Single Phase

Single phase SDTORK Actuator is provided with Stall duty

motor used for quarter turn application. Actuator is suitable

for inching operation too and they can be supplied with

extra limit switches for remote position indication.

The Actuator are available in general purpose, Dust proof

& Flame proof & Explosion proof housing.

Three phases SDTORK Actuator is basically a worm gear

type reduction gear box. A single stage grease bath worm

gear gives quietness and reliability in operation. The valve

can be fully opened, fully closed or adjusted to any

intermediate position. The rectory force on the worm shaft

which is a 'Floating one' is directly proportional to the out

put torque and is absorbed by a set of disc springs. The

lateral movement of the worm shaft under load, trips

closes the Torque switch. The driving motor is a TEFC

squirrel cage class F IP 65 enclosure motor combining low

inertia with a high starting and stalling torque.

Three Phase

Three phase Actuator are fitted with torque limit

switches & travel limit switches & also they are in

built with manual hand wheel used for operating the

actuator manually in case of power failure. Actuator is

also supplied with various shaft designs to suit rising

& non rising stem valve. Three phases are also

provided with space heater. This actuator is also

available in slow mode operation which is used for

multi turn application.

Easier interface with digital control devices. Electrical actuators must have a voltage selection, typical actuators voltages

are 24V AC, 110V AC, 240 V AC and 415 Volts. Fail safe electric actuators are also called spring return and the fail

positioning (open or closed) should be noted. For detail on the Electric actuator refer Sdtork and asked for detailed

literature. The spring return Electrical actuators are available for low torque, for higher values we suggest you to use

reversible stay put type actuator

Electric Actuator

SUDE13 1258/1268 & 1358/1368 SERIES


Notes :

?Actuator rating is for valve working pressure 10 kg / cm².

?Timing given is approximate and is useful as an indicating figure.

?All data is complied in laboratory test, in actual field, working may differ.

?Width and weight will change with rating of flanges and accessories.

Common Accessory for Single Phase / Three Phase

Actuator :

a) Honeywell / any other make PID Controller along with PT 100 sensor

with built in panel as an option.

b) Honeywell / any other make pressure Transmitter where based on

setting pressure valve will open & close through PID with built in panel

as a option.

c) Sequential timer 0 to 30 channel for sequence operation.

d) Cyclic timer having On time - 1 to 60 seconds & Off time - 1 to 60 min

for sequencing operation.

e) Stimulatror - panel mounting type having two knobs used for

generating 4 to 20 mA with the help of 230 Volt A.C. Supply.

a) Travel Limit Switches - 2 nos

b) Auxiliary Limit Switches - 2 nos

c) Hand wheel for Manual operation

d) Local position indicator

e) Potentiometer for feed back

f) Torque limit switches

g) Position Transmitter

The Actuators can be supplied with a panel

having Auto Calibration facility.

Actuator can also be supplied with :

Single Phase OR Three phase Panel for switching the valve On / Off

through Push Buttons for local operation under manual mode OR through

PLC under Auto mode through 4-20 mA, 0 to 10 V DC.

Accessories For Electric Actuator

Control Panel Specification :

a) Input : Single Phase 230 V AC OR 3 Phase 415 V AC, 4 wire supply.

b) Output supply: Single Phase 230 V AC OR 3 phase 415 V AC Reversible

supply.

c) Auto / Manual selection : Selector switch provided. In Auto mode open &

close operation is controlled by 4-20mA Input & under Manual mode

operation is through Push buttons.

d) Indications : Zero to a100% valve position display, R, Y, B Phase Indication

[applicable only for 3 phase] Open & Close, Fully open & Fully close

indication.

e) Main switch - Single Phase OR 3 Phase MCB for mains On / Off.

f) Phase fail / error protection provided.

g) Fuse protection provided for each phase.

h) Protection from over torque - If Actuator gets over torque the torque switch

trips & the system protects the motor. Also provided with 10 metes cable for

Motor & Feed back with connectors.

14SUDE 1258/1268 & 1358/1368 SERIES

Wall Mounted Constructionin sheet metal

Integral Construction


I

G

2

3

1

45

6

7

8

9

10

H

F

n eØ

B

A

C

D

E

J

11

12

13

Plastic Butterfly Valve with Pneumatic Rotary Spring / Double Acting Actuator

VALVESIZE ACTUATOR MODEL NUMBER

Cv WT. OFASSY

IN KGS.

50

65

80

100

125

150

200

250

300

350

400

450

500

600

Approximate Time

for open In Sec. In Sec.

Air Consumption Lts of Free Air

To Open To Closefor close

1268/50/PVC/PVC/DAW

1268/50/PVC/PVC/SAOO

1268/65/PVC/PVC/DAW


1268/80/PVC/PVC/DAOO


1268/100/PVC/PVC/DA05

1268/100/PVC/PVC/SA10

1268/125/PVC/PVC/DA05

1268/125/PVC/PVC/SA10

1268/150/PVC/PVC/DA10

1 268/150/PVC/PVC/SA15

1268/200/PVC/PVC/DA20

1268/200/PVC/PVC/SA20

1268/250/PVC/PVC/DA20

1268/250/PVC/PVC/SA25

1268/300/PVC/PVC/DA25

1268/300/PVC/PVC/SA25

1268/350/PVC/PVC/DA40

1268/350/PVC/PVC/SA40

1268/400/PVC/PVC/DA40

1268/400/PVC/PVC/SA50

1268/450/PVC/PVC/DA50

1268/450/PVC/PVC/SA50

1268/500/PVC/PVC/DA50

1 268/500/PVC/PVC/SA50

1268/600/PVC/PVC/DA50

1268/600/PVC/PVC/SA70

B

143.5

143.5

160

194

194

236

312

312

362

598

598

694

694

694

C

8

8

8

8

10

10

10

10

10

10

10

10

16

16

16

16

16

16

32

32

32

32

32

32

32

32

32

32

D

7.5

7.5

7.5

7.5

11

11

11

11

11

11

11

11

11

11

11

11

11

11

20

20

20

20

20

20

20

20

20

20

E

20

20

20

20

30

30

30

30

30

30

30

30

30

30

30

30

30

30

50

50

50

50

50

50

50

50

50

50

A

109

109

125

146

146

182

234

234

276

444

444

524

524

524

6.15

6.3

6.65

6.8

9

9.25

10.9

11.98

17.1

18.18

21.57

23.65

37.17

37.36

52.57

58.2

92

95.3

110.7

129.5

130.6

171.4

272.7

300.4

318.7

346.4

396.7

451.7

0.2

0.3

0.2

0.4

0.3

0.5

0.4

0.5

0.4

0.6

0.5

0.8

0.6

1

1

1.6

1.2

2.4

1.2

4

2.4

8

4

8

4

8

4

14

0.075

0.15

0.15

0.28

0.28

0.28

0.28

0.35

0.35

0.65

0.65

0.8

1.5

1.5

2.05

2.05

2.05

5.3

5.3

5.3

5.3

10.5

10.5

10.5

10.5

10.5

10.5

10.5

H

120.65

120.65

139.7

139.7

152.4

152.4

190.5

190.5

215.9

215.9

241.55

241.55

298.45

298.45

361.95

361.95

431.8

431.8

476.25

476.25

539.75

539.75

577.85

577.85

635

635

749.3

749.3

I

85

85

85

85

110

110

122

122

122

122

127

127

161

161

161

161

191

191

272

272

272

272

313

313

313

313

313

313

0.05

0.1

0.25

0.25

0.32

0.55

1.2

1.9

1.9

5.3

5.3

7

7

7

0.2

0.3

0.2

0.4

0.3

0.5

0.4

0.5

0.4

0.6

0.5

0.8

0.6

1

1

1.6

1.2

2.4

1.2

4

2.4

8

4

8

4

8

4

31

F

83.82

83.82

91.44

91.44

106.68

106.68

119.38

119.38

132.08

132.08

142.24

142.24

170.18

170.18

210.82

210.82

243.84

243.84

269.24

269.24

299.72

299.72

314.96

314.96

350.52

350.52

406.4

406.4

G

109.22

109.22

119.38

119.38

134.62

134.62

149.86

149.86

167.64

167.64

182.88

182.88

213.36

213.36

241.3

241.3

297.18

297.18

325.12

325.12

350.52

350.52

370.84

370.84

401.32

401.32

464.82

464.82

J

278.04

278.04

295.82

295.82

351.3

351.3

391.24

391.24

421.72

421.72

452.12

452.12

544.54

544.54

613.12

613.12

732.02

732.02

866.36

866.36

922.24

922.24

998.8

998.8

1064.8

1064.8

1184.2

1184.2

n

4

4

4

4

4

4

8

8

8

8

8

8

8

8

12

12

12

12

12

12

16

16

16

16

20

20

20

20

e

0.75

0.75

0.75

0.75

0.75

0.75

0.75

0.88

0.88

0.88

0.88

0.88

0.88

1

1

1

1

1.12

1.12

1.14

1.14

1.26

1.26

1.26

1.26

1.38

1.38

0.75

DIMENSIONS

65

65

120

120

160

160

280

280

430

430

640

640

1200

1200

1850

1850

2700

2700

3300

3300

4400

4400

6250

6250

6900

6900

10000

10000

060

130

130

240

240

320

320

560

560

860

860

1280

1280

2400

2400

3700

3700

5400

5400

6600

6600

8800

8800

12500

12500

13800

13800

20000

20000

090

SUDE15 1258/1268 & 1358/1368 SERIES

1268

PART LIST

S.No. DESCRIPTIONBODYDISCBONDED SEATSHAFTBEARINGO-RING SHAFTO-RING PLUG

1234567

PVC(STANDERED) PP(OPTIONAL) PVDF(OPTIONAL)PVC(STANDERED) PP(OPTIONAL) PVDF(OPTIONAL)EPDM.Viton403ssSTEEL +PTFEEPDM.VitonEPDM.Viton

MATERIAL S.No. DESCRIPTIONTAPPER PINPLUGTOP BUSHINGINDICADOR VISUAL POSITION INDICATORCILINDRO CYLINDERTAPA DOBLEEFECTO DOUBLE ACTING CAP

8910111213

AISI316C-15POLYACETALSD TORK MAKESD TORK MAKESD TORK MAKE

MATERIAL


G

M

H12

17, 18

13, 14, 15

16

F

E

8

4

9

10

2

3

1

6

7

11

5

A

J

D

B

L

IN

K

C

109

109

109

109

109

109

125

125

125

125

146

146

182

182

234

234

276

276

with Pneumatic Rotary Single / Double Acting ActuatorPlastic 2 Way Screwed Ball Valve


1368/15/PVC/PVC/DAW/BSP

1368/15/PVC/PVC/SAW/BSP


1368/20/PVC/PVC/SAW/BSP


1368/25/PVC/PVC/SA00/BSP



1368/40/PVC/PVC/DA00/BSP










B

15.01

15.01

20.29

20.29

26

26

30.48

30.48

38.1

38.1

48

48

67.05

67.05

80.01

80.01

102.1

102.1

C

53.69

53.69

63.5

63.5

72.99

72.99

81.99

81.99

97.79

97.79

120.21

120.21

150.11

150.11

182.88

182.88

226.06

226.06

E

8

8

8

8

8

10

8

10

10

10

10

10

10

10

10

16

16

16

WT. OFASSY

IN KGS.

0.7

0.7

0.75

0.75

0.87

1.02

1.07

1.22

1.99

2.49

2.83

3.91

4.92

7

8.53

8.34

11.79

17.42

15

20

25

32

40

50

65

80

100

22.22

22.22

25.4

25.4

28.57

28.57

31.75

31.75

34.92

34.92

38.1

38.1

44.45

44.45

47.62

47.62

57.15

57.15

D

0.075

0.075

0.075

0.075

0.075

0.075

0.15

0.15

0.15

0.15

0.28

0.28

0.33

0.33

0.8

0.8

1.5

1.5

51.42

51.42

61.5

61.5

72.25

72.25

82.8

82.8

90.93

90.93

100.96

100.96

112.52

112.52

137.54

137.54

162.56

162.56

A

20

20

20

20

20

20

20

30

20

30

30

30

30

30

30

30

30

30

H

160.57

160.57

180.25

180.25

185.94

185.92

192.35

192.35

238.39

238.39

274.29

274.29

319.96

319.96

359.61

359.61

413.1

433.92

I

Approximate Time

0.2

0.3

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

for open In Sec.


To Open To Close

0.05

0.05

0.05

0.1

0.1

0.25

0.32

0.7

1.2

In Sec.for close

0.2

0.3

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

F

7.5

7.5

7.5

7.5

7.5

11

7.5

11

11

11

11

11

11

11

11

11

11

11

G

143.5

143.5

143.5

160

160

194

236

312

362

J

102 84

102.84

123.01

123.01

144.5

144.5

165.6

165.6

181.86

181.86

201.93

201.93

225.04

225.04

275.08

275.08

325.12

325.12

K

14.98

14.98

14.98

14.98

16

16

16

16

16

16

19.98

19.98

19.98

19.98

21.99

21.99

21.99

21.99

L

51.511

51.511

67

67

73.66

73.66

70.3

70.3

84.83

84.83

97.79

97.79

139.95

139.95

166.11

166.11

169.92

169.92

DIMENSIONS

M N

94.01

94.01

109.5

109.5

116.16

116.16

112.8

112.8

139.83

139.83

158.79

158.79

203.45

203.45

229.61

246.61

250.42

250.42

Cv

10

10

15

15

32

32

90

90

90

90

126

126

319

319

351

351

589

589

16SUDE 1258/1268 & 1358/1368 SERIES

1368

PART LIST

S.No. DESCRIPTIONSTEMBALLBODYSEAT CARRIERUNION NUTEND CONNECTORSEATSTEM O-RINGSEAT CARRIER O-RING

123456789

PVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDTEFLONEPDM.VITONEPDM.VITON

MATERIAL S.No. DESCRIPTIONBODY O-RINGSOLID END O-RINGINDICADOR VISUAL POSITION INDICATORPISTON GUIDEGUIDE RINGPISTON O-RINGTAPA DOBLEEFECTO DOUBLE ACTING CAPSPRING SETSPRING RETURN CAP

101112131415161718

EPDM.VITONEPDM.VITON

POLYACETALPOLYACETALNITRILE

DIN-17223-CALLUMININUM ALLOY

MATERIAL


G

M

H12

17, 18

13, 14, 15

16

E

F

8

4

9

10

2

3

1

6

7

11

5

A

J

D

BC

R

O

S

P

Q

19

L

IN

K

C

with Pneumatic Rotary Single / Double Acting ActuatorPlastic 2 Way Flange Ball Valve

S.No. DESCRIPTIONSTEMBALLBODYSEAT CARRIERUNION NUTEND CONNECTORSEATSTEM O-RINGSEAT CARRIER O-RINGBODY O-RING

12345678910

PVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDPVC,options,PP,CPVC,PVDTEFLONEPDM.VITONEPDM.VITONEPDM.VITON

MATERIAL S.No. DESCRIPTIONSOLID END O-RINGINDICADOR VISUAL POSITION INDICATORPISTON GUIDEGUIDE RINGPISTON O-RINGTAPA DOBLEEFECTO DOUBLE ACTING CAPSPRING SETSPRING RETURN CAPFLANGE

111213141516171819

EPDM.VITON


DIN-17223-CALLUMININUM ALLOYPVC, Options, PP, CPVC, PVDF

MATERIAL

PART LIST

VALVESIZE

ACTUATOR MODEL NUMBER

1368/15/PVC/PVC/DAW/FLG

1368/15/PVC/PVC/SAW/FLG


1368/20/PVC/PVC/SAW/FLG


1368/25/PVC/PVC/SA00/FLG



1368/40/PVC/PVC/DA00/FLG










15.01

15.01

20.29

20.29

26

26

30.48

30.48

38.1

38.1

48

48

67.05

67.05

80.01

80.01

102.1

102.1

53.69

53.69

63 .5

63.5

72.99

72.99

81 99

81.99

97.79

97.79

120.21

120.21

150.11

150.11

182.88

182.88

226.06

226.06

8

8

8

8

8

10

a

10

10

10

10

10

10

10

10

16

16

16

WT. OFASSY

IN KGS.

0.7

0.7

0.75

0.75

0.87

1.02

1.07

1.22

1.99

2.49

2.83

3.91

4.92

7

8.53

8.34

11.79

17.42

0.2

0.3

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

15

20

25

32

40

50

65

80

100

22.22

22.22

25.4

25.4

28.57

28.57

31.75

31.75

34.92

34.92

38.1

38.1

44.45

44.45

47.62

47.62

57.15

57.15

0.075

0.075

0.075

0.075

0.075

0.075

0.15

0.15

0.15

0.15

0.28

0.28

0.33

0.33

0.8

0.8

1.5

1.5

51.42

51.42

61.5

61.5

72.25

72.25

82.8

82.8

90.93

90.93

100.96

100.96

112.52

112.52

137.54

137.54

162.56

162.56

20

20

20

20

20

20

20

30

20

30

30

30

30

30

30

30

30

30

160.57

160.57

180.25

180.25

185.94

185.92

192.35

192.35

238.39

238.39

274.29

274.29

319.96

319.96

359.61

359.61

413.1

433.92

Approximate Time




0.05

0.05

0.05

0.1

0.1

0.25

0.32

0.7

1.2

0.2

0.3

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

7.5

7.5

7.5

7.5

7.5

11

7.5

11

11

11

11

11

11

11

11

11

11

11

102.84

102.84

123.01

123.01

144.5

144.5

165.6

165.6

181.86

181.86

201.93

201.93

225.04

225.04

275.08

275.08

325.12

325.12

14.98

14.98

14.98

14.98

16

16

16

16

16

16

19.98

19.98

19.98

19.98

21.99

21.99

21.99

21.99

51.511

51.511

67

67

73.66

73.66

70.3

70.3

84.83

84.83

97.79

97.79

139.95

139.95

166.11

166.11

169.92

169.92

DIMENSIONS

109

109

109

109

109

109

125

125

125

125

146

146

182

182

234

234

276

276

94.01

94.01

109.5

109.5

116.16

116.16

112.8

112.8

139.83

139.83

158.79

158.79

203.45

203.45

229.61

246.61

250.42

250.42

Cv

10

10

15

15

32

32

90

90

90

90

126

126

319

319

351

351

589

589

143.5

143.5

143.5

160

160

194

236

312

362

16

16

16

16

16

16

15

15

15

15

17

17

17

17

19

19

22

22

65

65 00

75

75 00

85

85

100

100

110

110

125

125

145

145

160

160

210

210

97

97

106

106

116

116

140

140

149

149

164

164

185

185

200

200

250

250

130

130

150

150

160

160

180

180

200

200

230

230

290

290

310

310

400

400

B C EDA H IF J K L M NG O P Q R S

14

14

14

14

14

14

17

17

17

17

17

17

17

17

17

17

17

17

SUDE17 1258/1268 & 1358/1368 SERIES

1368


8

E

7

1

5

4

6

A

F

2

3

B

C

I

K

J12

10, 11

13, 14, 15

9

G

H

M M

D

L

B

N

with Pneumatic Rotary Single / Double Acting ActuatorPlastic 3 Way Screwed Ball Valve

PART LIST

S.No. DESCRIPTIONSTEMBALLBODYSEATUNION NUTEND CONNECTORO-RING SEALSMOUNTING KITTAPA DOBLEEFECTO DOUBLE ACTING CAPSPRING SETSPRING RETURN CAPINDICADOR VISUAL POSITION INDICATORPISTON GUIDEGUIDE RINGPISTON O-RING

123456789101112131415

PVC,options,PP,CPVC,PVCPVC,options,PP,CPVC,PVCPVC,options,PP,CPVC,PVCTEFLONPVC,options,PP,CPVC,PVCPVC,options,PP,CPVC,PVCEPDM.VITONPVC,options,PP,CPVC,PVDF



MATERIAL


1368/15/PVC/PVC/DAW/3W/BSP

1368/15/PVC/PVC/SAW/3W/BSP


1368/20/PVC/PVC/SAW/3W/BSP


1368/25/PVC/PVC/SA00/3W/BSP



1368/40/PVC/PVC/DA00/3W/BSP










B

84

84

91

91

105

105

151

151

149

149

151

151

193

193

193

193

237

237

C

13

13

19

19

25

25

51

51

51

51

51

51

76

76

76

76

102

102

E

57

57

67

67

76

76

102

102

102

102

121

121

163

163

163

163

217

217

WT. OFASSY

IN KGS.

0.72

0.72

0.81

0.81

1

1.15

1.31

1.46

2

2.9

3.4

4.56

6.53

8.61

10.95

10.85

16.72

22.35

0.2

0.3

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

15

20

25

32

40

50

65

80

100

75

75

75

75

82

82

92

92

92

92

109

109

178

178

178

178

204

204

D

0.075

0.075

0.075

0.075

0.075

0.075

0.15

0.15

0.15

0.15

0.28

0.28

0.33

0.33

0.8

0.8

1.5

1.5

58

58

65

65

76

76

112

11?

109

109

111

111

150

150

150

150

178

178

A

7.5

75

7.5

7.5

7.5

11

7.5

11

11

11

11

11

11

11

11

11

11

11

H

143.5

143.5

143.5

160

160

194

236

312

362

I

Approximate Time




0.05

0.05

0.05

0.1

0.1

0.25

0.32

0.7

1.2

0.2

0.3

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

F

64

64

72

72

78

78

89

89

89

89

100

100

149

149

149

149

226

226

G

8

8

8

8

8

10

8

10

10

10

10

10

10

10

10

16

16

16

J

20

20

20

20

20

20

20

30

20

30

30

30

30

30

30

30

30

30

K

109

109

109

109

109

109

125

125

125

125

146

146

182

182

234

234

276

276

L

51.51

51.51

67

67

73.66

73.66

70.3

70.3

84.83

84.83

97.79

97.79

139.95

139.95

166.11

166.11

169.92

169.92

DIMENSIONS

M

100.75

100.75

108.5

108.5

118.83

118.83

127.15

127.15

134.41

134.41

157.89

157.89

247.97

247.97

261.05

261.05

288.96

288.96

N

210.51

210.51

233

233

260.66

260.66

313.3

313.3

325.83

325.83

357.79

357.79

210.95

210.95

537.11

537.11

610.92

610.92

Cv

10

10

15

15

32

32

90

90

90

90

126

126

319

319

351

351

589

589

18SUDE 1258/1268 & 1358/1368 SERIES

1368


8

G

7

1

5

4

6

A

F

H

2

3

B

C

K

M

L12

10, 11

13, 14, 15

9

I

J

O O

D

N

E

P

with Pneumatic Rotary Single / Double Acting ActuatorPlastic 3 Way Flange Ball Valve

VALVESIZE


1368/15/PVC/PVC/DAW/3W/FLG

1368/15/PVC/PVC/SAW/3W/FLG


1368/20/PVC/PVC/SAW/3W/FLG


1368/25/PVC/PVC/SA00/3W/FLG



1368/40/PVC/PVC/DA00/3W/FLG










B

84

84

91

91

105

105

151

151

149

149

151

151

193

193

193

193

237

237

C

13

13

19

19

25

25

51

51

51

51

51

51

76

76

76

76

102

102

E

98

98

117

117

121

121

132

132

152

152

171

171

220

220

221

221

265

265

WT. OFASSY

IN KGS.

1.26

1.26

1.49

1.49

1.87

2 02

2.36

2.56

3.39

4.29

5.49

6.57

9.17

11.25

13.81

13.62

21.75

27.38

0.2

0.3

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

15

20

25

32

40

50

65

80

100

75

75

75

75

82

82

92

92

92

92

109

109

178

178

178

178

204

204

D

0.075

0.075

0.075

0.075

0.075

0.075

0.15

0.15

0.15

0.15

0.28

0.28

0.33

0.33

0.8

0.8

1.5

1.5

58

58

65

65

76

76

112

112

109

109

111

111

150

150

150

150

178

178

A

64

64

72

72

78

78

89

89

89

89

100

100

149

149

149

149

226

226

H

8

8

8

8

8

10

8

10

10

10

10

10

10

10

10

16

16

16

I

Approximate Time




0.05

0.05

0.05

0.1

0.1

0.25

0.32

0.7

1.2

0.2

0.3

0.2

0.3

0.2

0.3

0.3

0.4

0.3

0.4

0.4

0.5

0.5

0.6

0.8

1

1

1.6

F

171

171

191

191

216

216

293

293

301

301

311

311

404

404

406

406

480

480

J

7.5

7.5

7.5

7.5

7.5

11

7.5

11

11

11

11

11

11

11

11

11

11

11

K

143.5

143.5

143.5

160

160

194

236

312

362

L

20

20

20

20

20

20

20

30

20

30

30

30

30

30

30

30

30

30

DIMENSIONS

M

109

109

109

125

125

146

182

234

276

N

51.51

51.51

67

67

73.66

73.66

70.3

70.3

84.83

84.83

97.79

97.79

139.95

139.95

166.11

166.11

169.92

169.92

Cv

10

10

15

15

32

32

90

90

90

90

126

126

319

319

351

351

589

589

G

57

57

67

67

76

76

102

102

102

102

121

121

163

163

163

163

217

217

O

100.75

100.75

108.5

108.5

118.83

118.83

127.15

127.15

134.41

134.41

157.89

157.89

247.97

247.97

261.05

261.05

288.96

288.96

P

224.51

224.51

259

259

276.66

276.66

294.3

294.3

328.83

328.83

377.79

377.79

537.95

537.95

565.11

565.11

638.92

638.92

PART LIST

S.No. DESCRIPTIONSTEMBALLBODYSEATUNION NUTEND CONNECTORO-RING SEALSMOUNTING KITTAPA DOBLEEFECTO DOUBLE ACTING CAPSPRING SETSPRING RETURN CAPINDICADOR VISUAL POSITION INDICATORPISTON GUIDEGUIDE RINGPISTON O-RING

123456789101112131415

PVC,options,PP,CPVC,PVCPVC,options,PP,CPVC,PVCPVC,options,PP,CPVC,PVCTEFLONPVC,options,PP,CPVC,PVCPVC,options,PP,CPVC,PVCEPDM.VITONPVC,options,PP,CPVC,PVDF



MATERIAL

SUDE19 1258/1268 & 1358/1368 SERIES

1368


with Single Phase Electric Actuator Plastic Butterfly Valve

H

I J

14

12

11

13

E

D

C

n eØ

6B

1

2

3

45

7

8

9

10

A

F G

PART LIST

S.No. DESCRIPTIONBODYDISCBONDED SEATSHAFTBEARINGO-RING SHAFTO-RING PLUGTAPPER PINPLUGTOP BUSHINGCABLE GLANDSELECTRIC ACTUATORMOTOR(TEFC/TESC)HAND WHEEL

1234567891011121314

PVC(STANDERED) PP(OPTIONAL) PVDF(OPTIONAL)PVC(STANDERED) PP(OPTIONAL) PVDF(OPTIONAL)BN,EPDM,VITON403SSSTEEL + PTFEEPDM,VITONEPDM.VITONAISI316C-15POLYACETALSD TORK MAKESD TORK MAKESD TORK MAKESD TORK MAKE

MATERIAL


1258/50/PVC/PVC/SD03



1258/100/PVC/PVC/SD03

1258/125/PVC/PVC/SD05

1258/150/PVC/PVC/SD10

1258/200/PVC/PVC/SD20

1258/250/PVC/PVC/SD20

1258/300/PVC/PVC/SD30

Cv

B

3.3

3.6

4.2

4.7

5.2

5.6

6.7

8.3

9.6

C

109

119

134

149

167

182

213

241

297

120

139

152

190

215

241

298

361

431

E

182.6

183.3

184.5

185.6

186.8

262.8

265.1

267.8

282.3

65

120

160

280

430

640

1200

1850

2700

175

175

175

175

175

250

250

250

261

WT. OFASSY

IN KGS.

13.7

14.2

16

17.4

24.6

31.7

46.6

62

99.1

17

17

17

17

17

20

20

20

26

D

215

215

215

215

225

270

285

285

355

100

100

100

100

100

100

100

100

100

A F G H I J n e

130

240

320

560

860

1280

2400

3700

5400

68

68

68

68

68

95

95

95

123

117

117

117

117

117

148

148

148

182

110

110

110

110

110

110

110

110

110

4

4

4

8

8

8

8

12

12

0.75

0.75

0.75

0.75

0.88

0.88

0.88

1

1

DIMENSIONS

060 090

50

65

80

100

125

150

200

250

300

Operatingtime/sec

20SUDE 1258/1268 & 1358/1368 SERIES

1258


8

4

9

10

2

3

1

6

7

11

5

A

L

D

B

MK

O

N

P

I

C

H

G

FE

12

13

14

with Single Phase Electric Actuator Plastic 2 Way Screwed Ball Valve

PART LIST

S.No. DESCRIPTIONSTEMBALLBODYSEAT CARRIERUNION NUTEND CONNECTORSEATSTEM O-RINGSEAT CARRIER O-RINGBODY O-RINGSOLID END O-RINGELECTRIC ACTUATORMOTORHAND WHEEL

1234567891011121314

PVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFTEFLONEPDM,VITONEPDM,VITONEPDM,VITONEPDM,VITONSDTORK MAKESDTORK MAKESDTORK MAKE

MATERIAL

VALVESIZE


1358/15/PVC/PVC/SD03/BSP









B

15.0

20.29

26

30.48

38.1

48

67.05

80.01

102.1

C

53.69

63.5

72.99

81.99

97.79

120.21

150.11

182.88

226.06

E

68

68

68

68

68

68

95

95

123

WT. OFASSY

IN KGS.

8.25

8.3

8.42

8.62

9.99

10.33

15.05

17.58

33.22

17

17

17

17

17

17

20

20

26

22.22

25.4

28.57

31.75

34.92

38.1

44.45

47.62

57.15

D

51.422

61.5

72.25

82.8

90.932

100.96

112.52

137.54

162.56

A

253.35

273.75

285.15

286.291

308.72

393

465.001

507.55

543.96

H

51.511

67

73.66

70.3

84.83

97.79

139.95

166.11

169.92

I

Approximate Time


for close

17

17

17

17

17

17

20

20

26

F

117

117

117

117

117

117

148

148

182

J

139.01

154.5

161.16

157.8

172.33

185.29

264.95

291.11

300.42

K

100

100

100

100

100

100

100

100

100

L

102.84

123.01

144.5

165.6

181.86

201.93

225.04

275.08

325.12

DIMENSIONS

M

110

110

110

110

110

110

110

110

110

N

145

145

145

145

160

160

170

185

242

Cv

10

15

32

90

90

126

319

351

589

G

175

175

175

175

175

175

250

250

261

O

215

215

215

215

225

225

215

285

355

P

32

32

32

32

32

32

37

37

57

15

20

25

32

40

50

65

80

100

SUDE21 1258/1268 & 1358/1368 SERIES

1358


8

4

9

10

2

3

1

6

7

11

5

A

L

D

BC

T

M

U

K

J

12

PO

R

Q

S

N

I

C

H

G

FE

12

15

14

with Single Phase Electric Actuator Plastic 2 Way Flange Ball Valve

VALVESIZE


1358/15/PVC/PVC/SD03/FLG









B

15.0

20.29

26

30.48

38.1

48

67.05

80.01

102.1

C

53.69

63.5

72.99

81.99

97.79

120.21

150.11

182.88

226.06

E

68

68

68

68

68

68

95

95

123

WT. OFASSY

IN KGS.

8.25

8.3

8.42

8.62

9.99

10.33

15.05

17.58

33.22

17

17

17

17

17

17

20

20

26

22.22

25.4

28.57

31.75

34.92

38.1

44.45

47.62

57.15

D

51.422

61.5

72.25

82.8

90.932

100.96

112.52

137.54

162.56

A

253.35

273.75

285.15

286.291

308.72

393

465.001

507.55

543.96

H

51.511

67

73.66

70.3

84.83

97.79

139.95

166.11

169.92

I

Approximate Time


for close

17

17

17

17

17

17

20

20

26

F

117

117

117

117

117

117

148

148

182

J

97

106

116

140

149

164

185

200

250

K

65

75

85

100

110

125

145

160

210

L

102.84

123.01

144.5

165.6

181.86

201.93

225.04

275.08

325.12

DIMENSIONS

M

16

16

16

15

15

17

17

19

22

N

139.01

154.5

161.16

157.8

172.33

185.29

264.95

291.11

300.42

Cv

10

15

32

90

90

126

319

351

589

G

175

175

175

175

175

175

250

250

261

O

100

100

100

100

100

100

100

100

100

P

110

110

110

110

110

110

110

110

110

15

20

25

32

40

50

65

80

100

Q

145

145

145

145

160

160

170

185

242

R

215

215

215

215

225

225

215

285

355

S

32

32

32

32

32

32

37

37

57

T

130

150

160

180

200

230

290

310

400

U

14

14

14

17

17

17

17

17

17

PART LIST

S.No. DESCRIPTIONSTEMBALLBODYSEAT CARRIERUNION NUTEND CONNECTORSEATSTEM O-RINGSEAT CARRIER O-RINGBODY O-RINGSOLID END O-RINGFLANGEELECTRIC ACTUATOR STAY PUT TYPE SD TORK MALEMOTORHAND WHEEL

12345678910111213

1415

PVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFTEFLONEPDM.VITONEPDM.VITONEPDM.VITONEPDM.VITONPVC,options,PP,CPVC,PVDFSDTORK MAKE

SDTORK MAKESDTORK MAKE

MATERIAL

22SUDE 1258/1268 & 1358/1368 SERIES

1358


LM

N

O

P

J

12

1

E

2

8

4

5

3

A

F

7

6

B

C

D

B

K

I

HG

9

11

10

with Single Phase Electric Actuator Plastic 3 Way Screwed Ball Valve

VALVESIZE











B

84

91

105

151

149

152

193

193

237

C

13

19

25

51

51

51

76

76

102

E

57

67

76

102

102

121

163

163

217

WT. OFASSY

IN KGS.

8.27

8.36

8.55

8.86

10.4

10.98

16.66

20.01

38.15

17

17

17

17

17

17

20

20

26

75

75

82

92

92

109

178

178

204

D

58

65

76

112

109

111

150

150

178

A

117

117

117

117

117

117

148

148

182

H

175

175

175

175

175

175

250

250

261

I

Approximate Timefor open

In Sec. In Sec.

for close

17

17

17

17

17

17

20

20

26

F

64

72

78

89

89

100

149

149

226

J

162.5

162.5

169.5

179.5

179.5

196.5

265.5

265.5

291.5

K

334

341

362

418

416

436

621

621

702

L

110

110

110

110

110

110

110

110

110

DIMENSIONS

M

100

100

100

100

100

100

100

100

100

N

215

215

215

215

225

225

215

285

355

Cv

10

15

32

90

90

126

319

351

589

G

68

68

68

68

68

68

95

95

123

O

145

145

145

145

160

160

170

185

242

P

32

32

32

32

32

32

37

37

57

15

20

25

32

40

50

65

80

100

PART LIST

S.No. DESCRIPTIONMOUNTING KIT(Optional)O-RING SEALSEND CONNECTORASSEMBLY NUTTEFLON SEATSBODYBALLSTEMELECTRIC ACTUATORMOTORHAND WHEELCABLE GLANDS

123456789101112

MATERIALPVC,options,PP,CPVC,PVDFEPDM.VITONPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFSDTORK MAKESDTORK MAKESDTORK MAKESDTORK MAKE

SUDE23 1258/1268 & 1358/1368 SERIES

1358


D

E

M

K

JI

9

11

10

NO

P

Q

R

1

G

2

8

4

5

3

A

F

H

7

6

B

C

L

12

with Single Phase Electric Actuator Plastic 3 Way Flange Ball Valve

VALVESIZE











B

84

91

105

151

149

152

193

193

237

C

13

19

25

51

51

51

76

76

102

75

75

82

92

92

109

178

178

204

E

98

117

121

132

152

171

220

221

265

58

65

76

112

109

111

150

150

178

WT. OFASSY

IN KGS.

8.36

8.46

8.79

9.09

10.55

11.22

16.06

18.48

35.26

17

17

17

17

17

17

20

20

26

D

64

72

78

89

89

100

149

149

226

68

68

68

68

68

68

95

95

123

A F G H I J K L

Approximate Timefor open

In Sec. In Sec.

for close

17

17

17

17

17

17

20

20

26

171

191

216

293

301

311

404

406

480

117

117

117

117

117

117

148

148

182

175

175

175

175

175

175

250

250

261

162.5

162.5

169.5

179.5

179.5

196.5

265.5

265.5

291.5

DIMENSIONS

M

348

367

378

399

419

455

648

649

730

N

110

110

110

110

110

110

110

110

110

Cv

10

15

32

90

90

126

319

351

589

O P

57

67

76

102

102

121

163

163

217

100

100

100

100

100

100

100

100

100

215

215

215

215

225

225

215

285

355

15

20

25

32

40

50

65

80

100

Q

145

145

145

145

160

160

170

185

242

R

32

32

32

32

32

32

37

37

57

PART LIST

S.No. DESCRIPTIONMOUNTING KIT(Optional)O-RING SEALSEND CONNECTORASSEMBLY NUTTEFLON SEATSBODYBALLSTEMELECTRIC ACTUATORMOTORHAND WHEELCABLE GLANDS

123456789101112

MATERIALPVC,options,PP,CPVC,PVDFEPDM.VITONPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFPVC,options,PP,CPVC,PVDFSDTORK MAKESDTORK MAKESDTORK MAKESDTORK MAKE

24SUDE 1258/1268 & 1358/1368 SERIES

1358


E

685 MAX

485

A

13

12

440

11

D

C

n Øe

B

79

2

3

4

5

8

16

10

VALVESIZE


1258/50/PVC/PVC/SD4000-20

1258/65/PVC/PVC/SD4000-20

1258/80/PVC/PVC/SD4000-20

1258/100/PVC/PVC/SD4000-20

1258/125/PVC/PVC/SD4000-20

1258/150/PVC/PVC/SD4000-20

1258/200/PVC/PVC/SD4000-20

1258/250/PVC/PVC/SD4000-35

1258/300/PVC/PVC/SD4000-35

B

83

91

106

119

132

142

170

210

243

C

109

119

134

149

167

182

213

241

297

120

139

152

190

215

241

298

361

431

E

347,6

348,3

349,5

350,6

351,8

352,8

355,1

357,8

361,3

340

340

340

340

340

340

340

450

450

WT. OFASSY

IN KGS.

55.7

56.2

58

59.4

65.6

69.7

83.6

109

146.1

130

240

320

560

860

1280

2400

3700

5400

D

0,75

0,75

0,75

0,75

0,88

0,88

0,88

1,00

1,00

A n e

DIMENSIONS

3,5-24

3,5-24

3,5-24

3,5-24

3,5-24

3,5-24

3,5-24

11-75

1,6-60

4

4

4

8

8

8

8

12

12

50

65

80

100

125

150

200

250

300

Cv

060 090

OPERATINGTIME/SEC

65

120

160

280

430

640

1200

1850

2700

PART LIST

S.No. DESCRIPTIONBODYDISCBONDED SEATSHAFTBEARINGO-RING SHAFTO-RING PLUGTAPPER PINPLUGTOP BUSHINGELECTRIC ACTUATORMOTOR (TEFC/TESC)HAND WHEEL

12345678910111213

MATERIALPVC(STANDERED) PP (OPTIONAL) PVDF (OPTIONAL)PVC(STANDERED) PP (OPTIONAL) PVDF (OPTIONAL)BN,EPDM, VITON403SSSTEEL + PTEFEPDM,VITONAISI316C-15POLYACETALSDTORK MAKESDTORK MAKESDTORK MAKESDTORK MAKE

Plastic Butterfly Valve with Three Phase Electric Actuator

SUDE25 1258/1268 & 1358/1368 SERIES

1258


Plastic Butterfly Valve with Three Phase Electric Actuator with Gear Box

26SUDE 1258/1268 & 1358/1368 SERIES

1258

6

4

5

3

2

79

8

1

10

n Øe

13

12

A

11

H

E

F

G

B

K

PART LIST

S.No. DESCRIPTIONBODYDISCBONDED SEATSHAFTBEARINGO-RING SHAFTO-RING PLUGTAPPER PINPLUGTOP BUSHINGELECTRIC ACTUATORMOTOR (TEFC/TESC)HAND WHEEL

12345678910111213

MATERIALPVC(STANDERED) PP (OPTIONAL) PVDF (OPTIONAL)PVC(STANDERED) PP (OPTIONAL) PVDF (OPTIONAL)BN,EPDM, VITON403SSSTEEL + PTEFEPDM,VITONEPDM,VITONAISI316C-15POLYACETALSDTORK MAKESDTORK MAKESDTORK MAKE


1258/350/PVC/PVC/SD4000-08-WG40

1258/400/PVC/PVC/SD4000-20-WG60

1258/450/PVC/PVC/SD4000-20-WG60

1258/500/PVC/PVC/SD4000-20-WG135

1258/600/PVC/PVC/SD4000-20-WG135

WT. OFASSY

IN KGS.

153.1

198

327

403

481

DIMENSIONS

350

400

450

500

600

CvOPERATING

TIME/SEC

1.6-60

7.5-94

7.5-94

17-200

17-200

485

485

485

485

485

A B

88

118

118

148

148

C

315

315

315

315

315

85

85

85

85

85

D E

269

299

314

350

406

325

350

370

401

464

F090

6600

8800

12500

13800

20000

060

3300

4400

6250

6900

10000

e

28

28

32

32

35

12

16

16

20

20

nK

450

580

580

700

700

H

476

539

577

635

749

682

767

802

899

1018

G


Head Office, Bangalore

Solenoid valves.

Pneumatically operated control valves.

motorised valves.

Pneumatic & Electric Operated Ball / Butterfly valves.

Pneumatic & motorised Dampers.

Pneumatic & motorised VIV Dampers.

Heavy duty – Single phase & Three phase actuators for operating Gates & chutes.

motorised Rising & Non-rising Sluice valve.

Pneumatic & motorised pinch valve.

Pneumatic & motorised Flush Bottom valve.

Entire range of Electrical Actuator.

And Instrumentation Product likes Pressure Transmitter, PID Controller, Flow meter etc., for System Integration.

OUR OTHER PRODUCTS:

NOTE : TECHNICAL SPECIFICATIONS, DETAILS & DIMENSIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. DIMENSIONS IN THE TABLE ARE APPROXIMATE SUBJECT TO FINAL CONFIRMATION BY SUDE.

vign

etgr

aphi

cs.

CA

T/1

258-

1358

/09-

10

SUDE ENGINEERING CORPORATION

No. 1106, 10th Main Road, R.P.C. Layout,

Near R.P.C. Layout Bus Stop, Hampinagar,

Bangalore - 560 104. Karnataka, India

Pune Office :

S.No. 40/4, Balaji Udyam Nagar, Tempo Chowk,

Wadgaon Sheri, Pune 411014. Maharashtra India.

Tel. : +91 20 6533 3549 / 6531 1091Fax : +91 20 2703 1161Cell : +91 9822980003E-mail : [email protected]

Tel. : +91 80 2330 2145 / 2314 1104 / 2340 2297Fax : +91 80 2330 5729Cell : +91 9845018216E-mail : [email protected] [email protected]

SUDER

An ISO 9001:2008 Certified Company


1268 plastic butterfly & ball valves with actuator

Documents

Transcript of 1268 plastic butterfly & ball valves with actuator