Vanair Manufacturing Inc. | 10896 West 300 North, Michigan City, IN 46360 800.526.8817 | sales@vanair.com | www.vanair.com

*specs subject to change without notice © 2019 Vanair Manufacturing Inc. 04/25/19

Page 1 of 2

125/160/185 CFM UNDERDECK HYDRAULIC DRIVEN

AIR COMPRESSOR (Excludes FORD®) BID SPECIFICATION

REVISED: April 25, 2019

Type: Vanair® 125/160/185 CFM underdeck hydraulic driven air compressor.

New and in current production. Capacity: 125-185 CFM free air at up to 150 PSIG operation. Compressor: Sullair® 10 series design oil flooded rotary screw. The air compressors shall be completely

manufactured and assembled in the USA. Air compressor inlet control valve shall be an integral design incorporated in the cast iron housing. No bolt on inlet control valves

Hydraulic Motor: Directly coupled gear type hydraulic motor. Hydraulic Requirements & Input Speed:

Ratings per CAGI/PNEUROP PN2CPTC3

Gear Ratio: Air Compressor gear ratio shall be 3.95:1 to ensure lowest possible engine speed. Air Intake Filters: Separate two-stage, heavy duty, dry-type air filters shall be provided for air compressor. Air Receiver: The tank shall be ASME code approved rated at a 250 PSIG working pressure. It shall be

equipped with an ASME air pressure relief valve located upstream of the final oil separator. The receiver shall be equipped with a fill cap and easily readable sight glass, ¾″ service valve and a 25 micron full flow spin-on replaceable filter canister with built in bypass protection. Receiver tank (In.): 10.25D x 21.5L

Air/Fluid Separator: Separator element to be located internally in air receiver tank. Separator shall be

constructed with metallic end cap and in-flow nozzle plate with O-ring seals. Vanair separator shall provide for enhanced air quality, reduced operating and maintenance cost and optimized compressor performance. Separator to be warranted for 5 years or 3000 hours.

Cooling System: Compressor cooling system shall allow rated air delivery and pressure operation

continuously in 125 °F ambient temperatures. Cooler to be mounted in a powder-coated sheet metal enclosure with a suction type fan assembly and utilize SAE O–ring fittings (No ABS plastic shrouding). A dual cooler shall be provided for 185 CFM at 150 PSI.

Controls: Pneumatic inlet control valve shall be integrated into compressor system and automatically

modulate output from 0 to 100% in response to air demand.

Capacity (CFM)

Air Pressure (PSI)

Hyd. Flow (GPM)

Hydraulic Pressure (PSI)

Input Speed (RPM)

125 100 27.6 2100 1330 125 150 29.2 2620 1330 160 100 36.8 2200 1675 160 150 38.3 2700 1675 185 100 42.2 2400 1920 185 150 44.2 2830 1920

Vanair Manufacturing Inc. | 10896 West 300 North, Michigan City, IN 46360 800.526.8817 | sales@vanair.com | www.vanair.com

*specs subject to change without notice © 2019 Vanair Manufacturing Inc. 04/25/19

Page 2 of 2

125/160/185 CFM UNDERDECK HYDRAULIC DRIVEN AIR COMPRESSOR

General: The compressor shall be manufactured in an ISO 9001 certified quality system. Warranty: The air end is warranted for life when adhering to the prescribed maintenance schedule.

This warranty does not cover damage caused by accident, misuse, or negligence. If the compressor unit is disassembled the warranty is void. All other parts including the compressor unit shaft seal are warranted for twelve months subject to the same conditions mentioned above.

Service Centers: The air compressor manufacturer MUST have factory authorized service centers located in

each state of the United States of America and Canadian provinces. Installation: Systems must be installed by a factory authorized installation center. Options: External, Spin-on Air-Oil Separating Element Dual Pressure Dual Voltage Service/Control Line Moisture Separators Filter/Lubricator/Regulator (FLR) Air Hoses, Hose Reels and fittings OSHA Safety Valve (Velocity Fuse) Tool Oiler/Lubricator Biodegradable Vanguard Green™ Synthetic Oil