120712ChE128-3-FlashDist
Transcript of 120712ChE128-3-FlashDist
-
8/10/2019 120712ChE128-3-FlashDist
1/20
When is flash distillation used?
flash distillation a single equilibrium stage
1. when very crude separation is needede.g., oil/water separation in crude oil refining
2. when volatilities of components in the
mixture are very different
e.g., water desalination (4000 plants worldwide,
producing 3.4 billion gallons potable H2O daily)
-
8/10/2019 120712ChE128-3-FlashDist
2/20
http://www.edwardsmoving.com/Flash%20Drum.html
Flash drum 126' x 12' @ 179,000 lbs.,
being moved into position on 4 self propelled steerable dollies at a major oil refinery.
-
8/10/2019 120712ChE128-3-FlashDist
3/20
10 x 5.9 MIGD MSF units in Saudi ArabiaDESALINATION OF SEA WATER BY MULTISTAGE FLASH DISTILLATION
There are several consecutive stages (flash drums) maintained at decreasing pressures from the first
stage (hot) to the last stage (cold). Sea-water flows through the tubes of the heat exchangers,
where it is warmed by condensation of the vapor produced in each stage. Its temperature increases
from sea temperature to inlet temperature of the brine heater. The sea water then flows through
the brine heater where it receives the heat necessary for the process (generally by condensing
steam). At the outlet of the brine heater, when entering the first flash drum, sea water is
overheated compared to the temperature and pressure of stage 1. Thus it will immediately "flash,i.e., release heat, and thus vapor, to reach equilibrium with stage conditions. The vapor is
condensed into fresh water on the tubular exchanger at the top of the stage. The process takes
place again when the water is introduced into the following stage, and so on until the last and
coldest stage. The fresh water accumulates as the distillate, which is extracted from the last
(coldest) stage. Sea water becomes slightly concentrated from stage to stage and becomes the
brine flow, which is also extracted from the last stage.
http://www.sidem-desalination.com/en/process/MSF/
-
8/10/2019 120712ChE128-3-FlashDist
4/20
BIODIESEL MANUFACTURING
Biodiesel is made by transesterification of triglycerides
with methanol, using NaOH as the catalyst:
The products are glycerol and fatty acid methyl esters
(FAMEs). The latter are biodiesel.
The glycerol is much denser than the biodiesel, and
separates by gravity in a settler.
The biodiesel is purified by separating it from
methanol/water using simple flash distillation.
http://www.enerclean.biz/Equipment/Biodiesel/BiodieselFlash/BiodieselFlash.html
-
8/10/2019 120712ChE128-3-FlashDist
5/20
GLYCOL DEHYDRATION UNIT
The DPS Delta glycol dehydration unit removes water vapor from a gas stream to allow further
treatment and transportation without risk of hydrate formation or corrosion in the presence of
H2S or CO2, using ethylene glycol as a liquid desiccant.
http://www.dps-delta.com/portfolio/glycol.htm
-
8/10/2019 120712ChE128-3-FlashDist
6/20
GLYCOL DEHYDRATION PROCESS
Wet gas containing HC droplets enters the integral scrubber section of the contactor tower where free liquid is removed.
Saturated gas flows up through the mass transfer section of the tower mixing with the downward flowing lean glycol. Dry
gas will exit the tower via a demister pad and the rich glycol goes to a coil within the still column mounted on the reboiler.
The condensing vapors provide reflux for the still column.
The warmed rich glycol flows via the lean/ rich glycol exchanger to the Flash Drum to remove entrained gas and separateHC liquid from the rich glycol. The rich glycol then passes through a solids filter to remove particulates and a carbon filter to
remove traces of aromatic compounds. After filtering the rich glycol is heated by the lean glycol from the Surge Vessel .Lean
glycol flows from an integral gas stripping column via the Surge Drum to the Lean/ Rich Glycol Exchanger before flowing to
the Lean Glycol Pump which sends the glycol under high pressure to the Glycol Contactor via the Lean Glycol Cooler.
-
8/10/2019 120712ChE128-3-FlashDist
7/20
Flash drum schematic
feed easiest to pump if liquid
if necessary, increase pressure to keep it liquid (TF< Tbp)
to make feed partially vaporize, need Tdrum> Tbp, and Pdrum< PF flash is usually adiabatic (no heat transfer across the system boundary)
partial condensor operates in the same way, with hot vapor feed which partiallycondenses when cooled.
-
8/10/2019 120712ChE128-3-FlashDist
8/20
Case 1: specified Tdrum, PdrumTMB: F = L + V
CMB: F zi= L xi+ V yi
VLE: Ki= yi/ xi
solve for xi: xi=Fz
i
L+VKi
=
Fzi
(F V)+VKi
=
zi
1+ (Ki 1)V
F
can also express in terms of yi:
knowns: zi, Ki(Tdrum) unknowns: xi(or yi), V/F
xii =1 yi
i =1oralso need to use:
where V/F is the fraction of feed vaporized, 0 V/F 1
yi=
Kizi
1+ (Ki 1)V
F
-
8/10/2019 120712ChE128-3-FlashDist
9/20
Rachford-Rice Solutiontrial-and-error method (except binary); easy to program
xi
i
=1
iterate until convergence
then calculate xi, yivalues then use TMB to calculate V, L
possible solution:
faster convergence:
Rachford-Rice equation
andxi= zi
1+ (Ki 1)V
F
zi
1+ (Ki 1)V
Fi =1
yii xi=
i
Kizi
1+ (Ki 1)V
Fi
zi
1+ (Ki 1)V
Fi = 0
(Ki 1)z
i
1+ (Ki 1)VFi
= 0
-
8/10/2019 120712ChE128-3-FlashDist
10/20
Finding V/F
f VF( )=
(Ki 1)z
i
1+ (Ki 1)V
Fi = 0
algorithm for Newtonian convergence (Wankat, p. 37-8):
pick a value for V/F
evaluate f(V/F)
if f(V/F) 0, choose a new value for V/F
VF( )next =
VF( )prev
fprev
dfprev
dVF( )
where
df
dVF( )
=(K
i 1)2z
i
1+ (Ki 1)V
F
2i
-
8/10/2019 120712ChE128-3-FlashDist
11/20
Case 2: specify Pdrumand V/F
Guess Tdrum
Calculate Kivalues
Evaluate V/F using R-R equation
If f(V/F) 0, guess new Tdrum(recall Tbpcalculation)
Case 3: specify Pdrumand one xi(or yi) value
Guess Tdrum
Calculate a Kivalue
Calculate V/F using
Evaluate f(V/F) for this Tdrum
If f(V/F) 0, guess new Tdrum
orxi=
zi
1+ (Ki 1)V
F
yi=
Kizi
1+ (Ki 1)V
F
-
8/10/2019 120712ChE128-3-FlashDist
12/20
Ready! To design the flash drummeaning, how large?
Consider the flash drum as a vertical cylinder:
important size parameters:
diameter D
height hplacement of feed nozzle
materials issues:
high temperature?
high pressure?corrosive feed?
D
hF
V
L
If the flash drum is too small: bubble entrainment in L
liquid entrainment in V (demister helps)
Separation is compromised
If the flash drum is too large:- wasted expense
If the liquid volume is large: Use a horizontal drum instead
-
8/10/2019 120712ChE128-3-FlashDist
13/20
Vertical drum size
1. Calculate maximum permissible vapor velocity, uperm
(m/s)
uperm
= Kdrum
r
L r
V
r
V
where Kdrumis an empirical constant, typically 0.1 Kdrum 0.35
2. Calculate cross-sectional area, Ac(m)
Ac=
V(MWv)
uperm
r
V
where V is vapor flow rate and MWVis the vapor average molecular weight
3. Calculate drum diameter, D, and height, h
D=4A
c
rule-of-thumb: 3 h/D 5
-
8/10/2019 120712ChE128-3-FlashDist
14/20
Graphical solutionfor binary mixtures
CMB: F zi= L xi+ V yi
solve for yi: yi= -(L/V) xi+ (F/V) zi
equation of a straight linethe operating line
slope = -(L/V)
solution to the flash drum problem must simultaneously
satisfy CMB (operating line) and VLE (equilibrium line)
for a binary mixture, we can represent both on a 2D graph
-
8/10/2019 120712ChE128-3-FlashDist
15/20
McCabe-Thiele diagram
From Separation Process Engineering, Third Editionby Phillip C. Wankat
(ISBN: 0131382276) Copyright 2012 Pearson Education, Inc. All rights reserved.
Figure 2-2 McCabe-Thiele diagram for ethanol-water
yE= -(L/V) xE+ (F/V) zE
yE
xE
Find Tdrum?
yE/xE= KE(Tdrum)
simultaneoussolution of
CMB and VLE
-
8/10/2019 120712ChE128-3-FlashDist
16/20
Drawing the operating line
From Separation Process Engineering, Third Editionby Phillip C. Wankat
(ISBN: 0131382276) Copyright 2012 Pearson Education, Inc. All rights reserved.
Figure 2-2 McCabe-Thiele diagram for ethanol-water
yi= -(L/V) xi+ (F/V) ziyint= (F/V)zE
for specified feed (zi), Pdrumand V/F:
yint= (F/V) zi
-(L/V) = -(F-V)/V = 1 - (F/V)
when yi= xi,
yi= -(L/V) yi+ (F/V) zi
yi(1 + L/V) = (F/V) zi
yi(V + L)/V = (F/V) zi
i.e., yi= xi= zi
zE
all operating lines must
pass through this point
-
8/10/2019 120712ChE128-3-FlashDist
17/20
Limits of separation
From Separation Process Engineering, Third Editionby Phillip C. Wankat
(ISBN: 0131382276) Copyright 2012 Pearson Education, Inc. All rights reserved.
yi= -(L/V) xi+ (F/V) zi
for a given feed (zi), 0 (V/F) 1
(V/F) = 1 (vaporize all the feed)
(L/V) = (F-V)/V = (F/V)1 = 0
operating line is horizontal
corresponds to xmin
V/F = 0
(V/F) = 0 (vaporize no feed)
(L/V) = (F/V)1 =
operating line is vertical
corresponds to ymax
V/F = 1
xE,min
yE,max
zE
Figure 2-2 McCabe-Thiele diagram for ethanol-water
as x xmin, or yymax, product yield 0
to achieve finite yield, must have lessseparation
-
8/10/2019 120712ChE128-3-FlashDist
18/20
Energy balance (EB)
EB: FhF + Qflash= VHv + LhLwhere hF, hLare liquid enthalpies
HVis vapor enthalpy
all are functions of temperature, composition
0
assume flash drum is well-insulated, flash is adiabatic
for ideal mixtures and arbitrary Tref:
hi(T,x
i) = x
iC
PL,i
(T Tref)
i
Hi(T,y
i) = y
i
i+C
PV,i
(T Tref)
i
for a particular component i,
CP,Lis molar heat capacity of pure liquid
CP,Vis molar heat capacity of pure vapor
lis latent heat of vaporization at T = Tref
-
8/10/2019 120712ChE128-3-FlashDist
19/20
Feed temperature
EB: FhF = VHv + LhL
What temperature must the feed be to cause the flash?
Case 1: for specified TF, value of hFis knownthis determines values of HV, hLnecessary to satisfy
EB
i.e., Tdrumis determined
Case 2: for specified Tdrum, values of HV, hLare knownthis determines value of hFnecessary to satisfy
EB
i.e., TF is determined
-
8/10/2019 120712ChE128-3-FlashDist
20/20
Heating the feed
if the feed is not already at temperature TF, how much heat mustbe supplied?
energy balance on heater:
F h1(T1) + Qh = F hF(TF)
Qh = F (hFh1)
(dictates size of heater required)
F, zi, T1 F, zi, TF