1.0m-1.2m Dual Optic Offset AntennaTransmit-Receive

2

This PATRIOT ANTENNA equipment is warranted to be free from defects in material and workmanship un-der normal use and service. PATRIOT ANTENNA shall repair or replace defective equipment, at no charge, or at its option, refund the purchase price, if the equipment is returned to PATRIOT ANTENNA not more than twelve (12) months after shipment. Removal or reinstallation of equipment and its transportation shall not be at cost of PATRIOT ANTENNA except PATRIOT ANTENNA shall return repaired or replaced equipment freight prepaid.

This Warranty shall not apply to equipment which has been repaired or altered in any way so as to affect its stability or durability, or which has been subject to misuse, negligence or accident. This Warranty does not cover equipment which has been impaired by severe weather conditions such as excessive wind, ice, storms, lightning, or other natural occurrences over which PATRIOT ANTENNA has no control, and this War-ranty shall not apply to equipment which has been operated or installed other than in accordance with the instructions furnished by PATRIOT ANTENNA.

Claimants under this Warranty shall present their claims along with the defective equipment to PATRIOT ANTENNA immediately upon failure. Noncompliance with any part of this claim procedure may invalidate this warranty in whole or in part.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER AGREEMENTS AND WARRANTIES, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. PATRIOT ANTENNA DOES NOT AUTHORIZE ANY PERSON TO ASSUME FOR IT THE OBLIGATIONS CONTAINED IN THIS WARRANTY AND PATRI-OT ANTENNA NEITHER ASSUMES NOR AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE EQUIPMENT DELIVERED OR PROVIDED.

IN NO EVENT SHALL PATRIOT ANTENNA BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, IN-TERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND.

In no event shall PATRIOT ANTENNA be liable for damages in an amount greater than the purchase price of the equipment.

Some states do not allow limitations on how long an implied warranty lasts, or allow the exclusion or limita-tion of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

PATRIOT ANTENNA has the right to void the warranty when the antenna is installed by someone other then a certifi ed installer.

LIMITED TWELVE (12) MONTH WARRANTY

Product Serial Number- _________________Date Purchased- ____________

Patriot Antenna Systems704 North Clark StreetAlbion, MI 49224 USA Tel: (517)629-5990Fax: (517)629-6690

E-mail: info@sepatriot.com

3

. 1. Perform as many functions as possible on the ground.

2. Watch out for overhead power lines. Check the distance to the power lines before starting installation. We recommend you stay a minimum of 6 meters (20 feet) from all power lines.

3. Do not use metal ladders.

4. Do not install antenna or mast assembly on a windy day.

5. If you start to drop antenna or mast assembly, get away from it and let if fall.

6. If any part of the antenna or mast assembly comes in contact with a power line, call your local power company. DO NOT TRY TO REMOVE IT YOURSELF! They will remove it safely. 7. Make sure that the mast assembly is properly grounded.

WARNINGAssembling dish antennas on windy days can be dangerous. Because of the antenna surface, even slight winds create strong forces. For example, a 1.0m antenna facing a wind of 32 km/h (20 mph) can undergo forces of 269 N (60 lbs.). Be prepared to safely handle these forces at unexpected moments. Do not at-tempt to assemble, move or mount dish on windy days or serious, even fatal accidents may occur. PA-TRIOT ANTENNA SYSTEMS is not responsible or liable for damage or injury resulting from antenna installations.

WARNING Antennas improperly installed or installed to an inadequate structure are very susceptible to wind damage. This damage can be very serious or even life threatening. The owner and installer assumes full responsibil-ity that the installation is structurally sound to support all loads (weight, wind & ice) and properly sealed against leaks. PATRIOT ANTENNA SYSTEMS will not accept liability for any damage caused by a satellite system due to the many unknown variable applications.

INSTALLATION OF THIS PRODUCT SHOULD BE PERFORMED ONLY BY A PROFESSIONAL INSTALLER AND IS NOT RECOMMENDED FOR CONSUMER D.I.Y. (DO-IT-YOURSELF) INSTALLATIONS.

IMPORTANT!!!

WATCH FOR WIRES! Installation of this product near power lines is dangerous. For your own safety, follow these important safety rules.

4

Unpacking and Inspection

Shipping cartons should be unpacked and contents checked for damaged or missing parts. Should there be any parts thatare damaged or missing, please contact technical support for replacement.

Site Selection

The main objective of conducting a site survey utilizing a compass and inclinometer is to choose a mounting location on theground that will give you the greatest amount of swing for azimuth and elevation for present as well as future use. A thoroughpre-installation site survey is strongly recommended because it can alert you to any “look angle”, soil, wind or otherproblems.

The first and most important consideration when choosing a prospective antenna site is whether or not the area can providean acceptable “look angle” to the satellite. A site with a clear, unobstructed view facing south, southeast is required. Yourantenna site must be selected in advance so that you will be able to receive the strongest signal available. Also considerobstructions that may occur in the future such as the growth of trees.

It is important to conduct an on-site survey with a portable antenna or with a compass and clinometer to avoid interference,obstructions, etc.

When selecting “look angle”, be sure to observe and take readings approximately 10 deg to the left and right, above andbelow your selected “look angle”.

Before Ground Pole Installation, the soil type should be checked because soil conditions vary widely in composition andload bearing capacity. A soil check will help you to determine the typeand size of foundation required to provide a stable base for the antenna.

Before digging is done, information regarding the possibility of underground telephone lines, power lines, storm drains, etc.,in the excavation area should be obtained from the appropriate agency.

As with any other type of construction, a local building permit may be required before installing an antenna. It is the propertyowner’s responsibility to obtain any and all permits. Ground mounts are certified for 125 mph wind survival.

Introduction

Thank you for purching your Patriot Commercial Antenna. We trust that you will fi nd this to be a well designed product that will proved many years of reliable service. Please read this manual thoroughly before beginning assembly. For best results in the assembly process, perform each step in the same sequence as listed in this manual. Record the serial munber of the unit on to page two for future refferance and read the warrenty information. The serial number plate can be found on the pedestal mount.

5

ITEM NO. DESCRIPTION PART NO. REV NO. QTY 1 BRKT, 3” PIPE GRAY 210080G 000 2 2 BRKT, AZIMUTH GRAY 212081G 000 1 3 BRKT 1.2m D.O. FEED 212006 000 1 4 SUB REF, D.O. PAINTED 212007 000 1 5 CLEVIS, 3” ELEVATION SMALL 210082G 000 1 6 CLEVIS, UPPER ELEV BIG 210083G 000 1 7 THRD ROD,1/2NF X 13”FINE 3HT08130FS 000 1 SEE PG 9 SPACER, .25L x1.25od x .312 id 3HM11100 000 2 8 TUBE, 1.0m DUAL OPTIC FEED 210005 000 1 * TUBE, 1.2m DUAL OPTIC FEED 212005 000 1 9 ASSY, 1.0m BACK STRUCT. 210002G 000 1 * ASSY, 1.2m BACK STRUCT 212002G 000 1 10 REFLECTOR, 1..0M GRAY 2100-0002 000 1 * REFLECTOR, 1.2m GRAY 212001G 000 1

1

3 4

5

6

9

8

72

10

6

54.0

0A

BOVE

GRO

UND

24.0

0

A A

Rsd

dkL`

rs9

K<6

1║:1,

6.7║

'62l

l(nq

2║'6

5ll(N

-C-S

tahm

fO

ktla

vhsg

hm0c

df-

╕B

nmbq

dsd9

2///

orh

`s17

c`xr

+on

tqdc

`f`hm

rstm

chrs

tqad

crn

hk'@

kknv

bnm

bqds

d13

gntq

rds

shld

aden

qdhm

rs`k

k`sh

nmne

`msd

mm

`(╕

Rnh

kA

d`qh

mfB

`o`b

hsx

=1/

//or

e-╕

Fqnt

mc

sgd

@m

sdm

m`s

nld

ds`o

okhb

`akd

knb`

kB

ncdr

-

72.0

0

10.0

0

SEC

TION

A-A

# 5

REBA

RN

INE

INC

H LO

NG

D C B AABCD

12

34

56

788

76

54

32

1

THE

INFO

RMA

TION

CO

NTA

INED

IN T

HIS

DRA

WIN

G IS

THE

SO

LE P

ROPE

RTY

OF

PATR

IOT

AN

TEN

NA

SYS

TEM

S. A

NY

REPR

OD

UCTIO

N IN

PA

RT O

R A

S A

WHO

LEW

ITHO

UT T

HE W

RITT

EN P

ERM

ISSI

ON

OF

PATR

IOT

AN

TEN

NA

SYS

TEM

S IS

PRO

HIBI

TED

.

PRO

PRIE

TARY

AN

D C

ON

FIDE

NTIA

L

FRA

CTIO

NA

L1/

16"

AN

GUL

AR:

1

X

.062

"XX

.0

31"

XX

.015

"

DRA

WN

BY:

ENG

APP

R.

NO

TES:

DA

TEN

AM

ETIT

LE:

SIZE B

DW

G.

NO

.RE

V

SCA

LE: 1

:10

UNLE

SS O

THER

WIS

E SP

ECIF

IED:

SHEE

T 1

OF

1

REV

ISIO

NS

DES

CRI

PTIO

NRE

V.

DA

TEA

PPRO

VED

ZON

E

DPR

ATT

10/0

9/20

06

XXX

XXXX

XX

2 7/

8 O

R 3

" IN

-GR

OU

ND

PIP

E M

TM

ATE

RIA

L:

Tole

ranc

es:

DIM

ENSI

ON

S A

RE IN

INC

HES:

CO

RNER

S A

RE A

T 90

7

Non-Penetrating Mount (optional)

1. Assemble the Non-Penetrating mount per the supplied instructions to provide the mast forthe mount installation.

2. Refer to the ballast chart for the required ballast to be placed in the Non-Pen Ballast Trays.

NOTE: Higher elevation angles can use less ballast. If there are any possible future elevationadjustments that could result in a lower elevation angle use the 22 deg elevation angle fromthe chart for the ballast requirement!

Add-on Dual Tray(if necesary)

28 lb

9 blocks per tray

4x8x16 Block

Elevation(deg)

80 100 12522 259 480 82640 202 374 64460 116 216 372

100cm Ballast Chart

Ballast Required (lbs)Wind Speed (mph)

Dual Tray

Elevation(deg)

80 100 12522 411 733 1236

40 321 572 964

60 185 330 556

120cm Ballast Chart

Ballast Required (lbs)Wind Speed (mph)

***

* Installations in excess of 100 mph windspeed requirement are to be tethered.

8

Az-El Mount Assembly

1. Using the hardware illustrated, as-semble the Pipe brackets, Azimuthbracket, and Clevis bracket as shown.

AzimuthBracket

PipeBracket

Clevis

1x

11x

18x

5x 4x

1x

A

B

CD

E

F

A

AA

A

A

B

B

C

D

D

D

D

D

D

D

DD

D

EE

EE

EE

E

E

E

E

E

EE

F C

E

9

210002GASSY, 1.0m BACK STRUCT. 2120022G ASSY, 1.2m BACK STRUCT.

3HM11100SPACER, .25Lx1.25od x .312idFOR USE WITH 1.0m ONLY

2100-0002REFLECTOR, 1.0m GRAY212001GREFLECTOR, 1.2m GRAY

INSTALL CAP ON THIS END

Back Structure Assembly

1. Attach Refl ector to Back Structure as pictured below.

2. Insert plastic cap into end as pictured.

NOTE: Use the two spacers where shown as pictured below ONLY on 1.0m Antenna.

10

Mount Assembly

1. Attach the Antenna-Back StructureAssy to the Azimuth Bracket usingthe illustrated hardware.

2. Add the Elevation adjustmenthardware and Upper Clevis using thehardware shown.

3HN050125CNFHXSNUT, 1/2 NF COUPLING

3HT09130FS THRD ROD, 1/2 NF x 13”

1/2” WASHER ON BOTH SIDESOF THE CLEVIS

11

INSTALL CAP ON THIS END

INSTALL CAP ON THIS END

2. Assemble the Sub Reflector to the Feed Support Tube using 4- 1/4x2-1/2 bolts, washers.

3. Assemble the Feed horn, Filter, Radio, and LNB per the instruction sheet supplied in theFeed Assy Kit.

Feed Support Assembly

1. Bolt the Feed Support Tube to the Back Structure using 2- 3/8 bolts, washers(2 per) andnuts.

212006BRKT, 1.2M D.O. FEED

212007SUB REF., D.O. PAINTED

SEE FEED CHART AT THE END OF THIS MANUAL FOR INSTALLATION DIRECTIONS

210005TUBE, 1.0m D.O. FEED 202005TUBE, 1.2m D.O. FEED

12

Antenna Pointing

1) Begin by obtaining the correct Az/El pointing data for the satellite of interest based for your site location.

2) Using an inclinometer or position readout form controller placed on the enclosure drum surface, position the antenna to the specified elevation angle.

3) Manually scan the antenna (back-and-forth in the azimuth around the direction of the specified azimuth angle) to achieve the maximum transponder signal.

4) Next repeat the procedure for elevation.

5) Repeat this procedure alternating between the azimuth and elevation until maximum transponder signal is achieved.

ExternalToothedWasher

Grounding

Grounding Antenna Feed Cables

1. Ground antenna feed cables in accordancewith current National Electric code and local elec-tric codes. The illustration shows a typicalgrounding method.Clamps that provide a solid connection betweenground wire and a ground source should be used.

Grounding Non-PenetratingMount Frame (if applicable)

1. Ground the Non-Penetrating mountframe. The illustration shows a typicalgrounding method.Refer to the NEC Section 810 and local elec-tric codes for specific instructions on ground-ing the remaining end of the ground wire.

CoaxialCable(to LNB)

Ground BlockNEC Section 810

Ground WireNEC Section 810

Non-PenFrame

GroundLug

1/4” TappingBolt

13

1.0 m Type-Approved Ku-BandTx/Rx Antenna Systems

Intelsat Type-Approval #IA084A001.0 m Type-Approved Ku-BandTx/Rx Antenna Systems

Ka-Band Receive Transmit Receive TransmitPolarity Linear Linear Circular CircularFrequency 18.2 - 21.2 GHz 27.5 - 31 GHz 19.7-20.2 GHz 29.5-30 GHzFeed - 2 - Port XpolReturn Loss 17.7 dB typ 20 dB typ 16 dB typ 18 dB typInsertion Loss 0.3 dB typ 0.1 dB typ 0.5 dB typ 0.3 dB typTx/Rx Isolation 40 dB 80 dB 40 dB 80 dBFeed Interface WR42 WR28 WR42 WR28AntennaEfficiency 65% 65% 65% 65%Cross Polarization On Axis 30 dB 35 dB 21 dB 21 dBwithin 1 dB Beamwidth 22 dB 25 dB 21 dB 21 dBTx/Rx Sidelobe Level 29 - 25 log 100 /D < < 20°

-3.5 20° < < 26.3°32 - 25 log 26.3° < < 48°-10 48° <

Gain 44.2 dBi 47.8 dBi 44.6 dBi 48.1 dBi(29.75 Tx, 19.95 Rx)Noise Temperature 78K @ 30°EL --- 90K @ 10°EL ---

Ku-Band Transmit ReceivePolarity Linear LinearFrequency 13.75 - 14.5 GHz10.7 - 12.75 GHzFeed - 2 Port Xpol Return Loss 20 dB typ 17.7 dB typInsertion Loss 0.1 dB typ 0.3 dB typTx/Rx Isolation 80 dB 40 dBFeed Interface WR75 WR75Antenna Transmit ReceiveEfficiency 70% 70%Cross Polarization On Axis 35 dB 35 dB within 1 dB Beamwidth 26 dB 26 dBTx/Rx Sidelobe Level 29 - 25 log 100 /D < < 20°

-3.5 20° < < 26.3°32 - 25 log 26.3° < < 48°-10 48° <

Gain 41.9 dBi 40.2 dBi(14.125 Tx, 11.725 Rx)Noise Temperature --- 61K @ 10°EL

53K @ 30°ELDual Optics SpecsCross Polarization on axis 35 dB 35 dB typ within 1 dB Beamwidth 35 dB 35 dB typTx/Rx Sidelobe 29 - 25 log 2.5° < < 7°

Level +8 7° < < 9.2°32 - 25 log 9.2° < < 48°

-10 48° < Feed - 2 Port XpolReturn Loss 20 dB typ 17.7 dB typInsertion Loss 0.1 dB typ 0.3 dB typTx/Rx Isolation 80 dB 40 dBFeed Interface WR75 WR75Antenna SpecificationsEfficiency 70% 70%Midband Gain 41.9 dBi 40.2 dBi Noise Temperature --- 61 K @ 10° EL

--- 53 K @ 30° EL

Mechanical Dataf/D Ratio 0.635Focal Distance 25 in / 63.5 cmMount Type evation over AzimuthMast Pipe Size 3 in / 7.30 or 7.62 cm Offset Angle 22°Elevation Adjustment uous Fine AdjustmentAzimuth Adjustment ine, 360° ContinuousEnvironmental DataWind Loading

Operational 60 mph, gusts of 100 kph, gusts to Survival 120 mph 193 kph

TemperatureOperational -40° to 140° F ( -40° to 60°C)

Survival '-60° to 180°F ( -51° to 82°C)Rain

Operational 1.5 in/hr (3.1 cm/h)Survival 3 in/ hr (7.6 cm/h)

IceSurvival 2.5cm (1 inch) radial or 1.3cm (.5 inch)

14

1.2 m Tx/Rx Antenna Systems1.2 mTx/Rx Antenna Systems

Eutelsat Type Approval # EA-A020Intelsat Type Approval # IA083A00

Ku-BandTransmit Receive Transmit Receive Transmit

Frequency 5.7-6.725 GHz 3.625-4.2 GHz 5.85-6.425 GHz Frequency 10.7 - 12.75 GHz 13.75 - 14.5 GHzFeed - 2 Port Xpol intelsat approved Frequency 10.7 - 12.75 GHz 13.75-14.5 GHzReturn Loss 20 dB typ 17.7 dB typ 20 dB typ eutelsat approved Frequency 10.7 - 12.75 GHz 14.0 - 14.5 GHzInsertion Loss 0.1 dB typ 0.5 dB typ 0.3 dB typ Feed - 2 Port XpolTx/Rx Isolation 70dB 40 dB 60 dB Return Loss 17.7 dB typ 20 dB typFeed Interface WR137 or N WR229 WR137 or N Insertion Loss 0.3 dB typ 0.1 dBtypAntenna Tx/Rx Isolation 40 dB 80 dBEfficiency 72% 68% 68% Feed Interface WR75 WR75Cross Polarization On Axis 30dB 17.7 dB typ 17.7 dB Dual Optics Specifications within 1 dB Beamwidth 25 dB 17.7 dB typ 17.7 dB Cross Polarization on axis 35 dB 35 dB typTx/Rx Sidelobe Level 100 /D < < 48° within 1 dB Beamwidth 35 dB 35 dB typ

Tx/Rx Sidelobe 29 - 25 log 2.5° < < 7°Level 8 7° < < 9.2°

TXFLY-120C 32 - 25 log 9.2° < < 48°Midband Gain 36.4 dBi 32.2 dBi 36.1 dBi -10 48° < (6.138 Tx, 3.913 Rx) AntennaNoise Temperature 65 K@10 Efficiency 70% 70%

45K @ 30°EL 55K@ 30 Cross Polarization On Axis 30 dB 35 dB

within 1 dB Beamwidth 22 dB 26 dBTransmit Receive Transmit Tx/Rx Sidelobe better than 100 /D < < 20° 29 - 25 log

Frequency 27.5 - 31 GHz 19.7 - 20.2 GHz 29.5 - 30 GHz 20° < < 26.3° -3.5Feed - 2 Port Xpol 26.3° < < 48° 32 - 25 log Return Loss 20 dB typ 16 dB typ 18 dB typ 48° < -10Insertion Loss 0.1 dB typ 0.5 dB typ 0.3 dB typ Midband Gain 41.8 dBi 43.5 dBiTx/Rx Isolation 80 dB 40 dB 80 dB (14.125 Tx, 11.725 Rx)Feed Interface WR28 WR42 WR28 Noise Temperature 58 K @ 10° EL ---Antenna 53 K @ 30° EL ---

Efficiency 65% 65% 65% X-BandMidband Gain 49.5 dBi 46.1 dBi 49.6 dBi Polarity Receive TransmitNoise Temperature --- 86K @ 10°EL --- Frequency 7.25 - 7.75 GHz 7.9 - 8.4 GHz

81K @ 30°EL Feed - 2 Port XpolCross Polarization On Axis 30 dB 21 dB 21 dB Return Loss 17.7 dB typ 17.7dB within 1 dB Beamwidth 22 dB 21 dB 21 dB Insertion Loss 0.3 dB typ 0.2 dB typTx/Rx Sidelobe Level 100 /D < < 48° *Tx/Rx Isolation 30 dB 30 dB

Feed Interface WR112 WR112TXFCC-120KA Antenna Specifications

Efficiency 70% 70%Midband Gain 38.0 dBi 38.7 dBiNoise Temperature 50 K @ 10° ---

45 K @ 30°Cross Polarization On Axis 23 dB 21dB 1 dB beamwidth 23 dB 21 dBTx/Rx Sidelobe Level 100 /D < < 20° 29 - 25 log

20° < < 26.3° -3.526.3° < < 48° 32 - 25 log

48° < -10

C-Band Linear C-Band Circular Ku-Band Linear

Ka-Band Linear Ka-Band Circular

X-Band Circular

Mechanical Dataf/D Ratio 0.635Focal Distance 30 in / 76.2 cmMount Type Elevation over AzimuthMast Pipe Size 2 7/8 or 3 in / 7.30 cm or 7.62 cm O.D. Offset Angle 22°Elevation Adjustment 8° to 90° Continuous Fine AdjustmentAzimuth Adjustment + 3° Fine, 360° ContinuousEnvironmental DataWind Loading

Operational 100 kph, gusts to 130 kph Survival 193 kph

125mph Wind forcesWind Force

Overturning MomentTemperature

Operational ( -40° to 60°C)Survival ( -51° to 82°C)

RainOperational (3.1 cm/h)

Survival (7.6 cm/h)Ice

Survival 2.5cm (1 inch) radial or 1.3cm (.5 inch)

15

Notes:

16

Notes:

Tx Port

Rx PortX-BCir

Feed Assembly1. Attach the relevant Feed Assembly.2. Insert the Feed Assembly into the Feed holder and assemble to the Feed Support Tube using the hardware illustrated below.3. Insert plastic plug into end of feed support tube.

Rx Port

Plug

FeedHolder

FeedSupportTube

Tx Port

C-BandCircular

Tx Port

Rx Port

Tx Port

Rx PortX-BandCircular

Ka-BandLinear

Rx Ports

1. Adjust the Feed to the appropriate skew angleusing the provided scale reference.

NOTE: Refer to the chart on back for polarizationangle. Elevation and polarity are both dependent onsite azimuth and the difference between satellite andsite longitude.

NOTE: Some satellites have a slant angle withrespect to the satellite belt angle. Contact the satelliteoperator for details.

Feed Adjustment (Polarity tuning)

Feed Rotation ChartInstall site west Install site East of satellite of satellite CW CCW Northern Hemisphere CCW CW Southern Hemisphere

CW

CCWPolarity ScaleReading Points

LNB

BUC

2MOSF-001 REV002

KA-BandCircular Tx/Rx

Ku-Band Co-Pol Tx/Rx

Ku Band Rx

KA-BandLinear Tx/Rx

C-BandLinear

Ku Band Tx/Rx

Tx Port

Rx Port

Tx Port

Rx Port

Rx Port

Tx Port

Rx Port

Tx Port

Rx Port

Tx Port

Rx Port

C-Band Rx C-Band Dual Rx

Tx Port

R x Port

Equipment From The Industry’s Lead-ing Satellite Equipment

Manufacturer’s Available Together - In One Place...

We are Cal-Amp’s LARGESTSTOCKING DISTRIBUTOR!

No Long Lead Times...No Drop Ship Fees...

High Inventory...Great Prices...

Complete line of Quality Feedhorns,Receivers and Accessories - from aname you trust

W e A l s o O f f e r P r o d u c t s f r o m t h e f o l l o w i n g :

Durable Snow Covers for CommercialAntennas as well as Home System -Keep snow from interfering with yoursignal.

Prevent Snow & Ice from accumlulatingon your system with a De-Icing System.

Complete line of Antenna Controllers,Positioners and Software for yourmotorized applications.

Looking to increase yoursatellite’s reception? Tryupgrading your feedsystem to a Multi-BeamFeed. Receive up to 4simultaneous satellites

Products Also Avaliable from:

Offset VSAT& DBS Antennas Available!

• ADL • General Instruments• Baird • Norsat• Drake • Standard Comm• DX • Thomson-Saginaw• Force • Wegner

Toll Free 1-800-470-3510

2M10092 REV001

PATRIOT ANTENNA SYSTEMS704 NORTH CLARK STREET

ALBION, MICHIGAN 49224 USAWWW.SEPATRIOT.COM

Specifications

Electrical

Tx Band(GHz)Rx Band(GHz)Tx Gain dBi (Midband)Rx Gain dBi (Midband)EfficiencySide LobesCross Polarization (on axis)

MechanicalAntenna Size 1.0m (39.4”) 1.2m (47.3”)Offset Angle 22 degreesF/D 0.635Operational Wind 50mphSurvival Wind 125mphOperational Temp -40 to 140 FSurvival Temp -60 to 180 FRain Operational = 1/2in./hr

Survival = 3in./hrIce 1 in. Radial -or-

1/2 in. + 60mph windPole Size 2-7/8” or 3” OD

Ku Band Ka Band1.0m - 1.2m 1.0m - 1.2m13.75 - 14.5010.70 - 12.7541.90 - 43.5040.30 - 41.80 70% ITU-580-5 35dB

29.50 - 30.0019.70 - 20.2048.10 - 49.7044.60 - 46.00 65%