1 WELCOME TO Presentation on New Concepts in Supercritical Turbines Sanjoy Bhattacharya Dy. Genl....
-
Upload
german-stinchfield -
Category
Documents
-
view
231 -
download
2
Transcript of 1 WELCOME TO Presentation on New Concepts in Supercritical Turbines Sanjoy Bhattacharya Dy. Genl....
1
WELCOME TO
Presentation on New Concepts in Supercritical
Turbines
Sanjoy Bhattacharya
Dy. Genl. Manager, BHEL, Hardwar
2
3
HPT IPT LPT
CROSS SECTIONAL ARRANGEMENT OF 500 MW STEAM TURBINE
THREE CYLINDER TURBINE
4
Introduction of New Rating SetsMajor Objectives
Bring down equipment cost per MW
Having more Efficient & Reliable product
Utilize available Steam turbine modules
Provide Higher competitiveness
New Rating to compete with Chinese/ New Indian firms
5
600MW Steam turbine: Built from proven modules of existing 500 & 250 MW
Orders for 4x600 MW Raigarh-III (Jindal), 2x600 MW Malwa, 2x600 MW each Avantha / Videocon/ Visa Raigarh/ DB Power & 1 x 600 MW Rayalaseema received .
Module Combination• HP: H30-100• IP : M30-63• LP : N30-4x6.3
Salient features:• 4 cylinder turbine (2 LPs)• HP turbine with Extraction connection for 565 HRH Temp• IP turbine suitable for 537/565 0C inlet temp.
OPTIONS1. HP Turbine with Extraction & 565 Deg C HRH Temp 2. HP Turbine without Extraction & 537 Deg C HRH Temp
Orders for 2 sets - N Chennai, 2 sets –JITPL, 1 set -APGENCO & 2 sets Singareni received.
Steam parameters 170 ata / 537 0C/ (537-565) 0C
6
600MW Steam Turbine
Design Changes from existing 500 MW sets :
•HP module variant with Extraction• New Flow path in HP, IP & LP Turbines (with Advanced blading)
• Matching modifications in Rotors & Inner Casings
• New Bearing pedestal between 2 LP cylinders
• New design of Cross Around Pipe & its support
• Enhanced governing characteristics
600 MW Sub critical Sets
Steam Turbine
500/ 600 MW SUB CRITICAL CYCLE
WITH 2 HP HEATERS, 3 LP HEATERS
8
Introduction of Steam Turbine with supercritical parameters
As the fluid pressure increases, Latent Heat (Enthalpy of Steam –Enthalpy of Water) reduces.
At Critical point it becomes zero.
In physical terms at this pressure water transforms to steam spontaneously.
SUPER CRITICAL STEAM PARAMETERS:
PARAMETERS MORE THAN CRITICAL STATE• STEAM PRESSURE > 221.2 BAR• STEAM TEMPERATURE > 374.15 Deg C
ULTRA SUPERCRITICAL PRESSURE( 300 BAR)
INCREASE IN PRESSURE & MAIN AND REHEAT TEMP. > 537 Deg CRESULTS IN SIGNIFICANT IMPROVEMENT IN HEATRATE
0
5
10
15
20
25
30
35
40
45
500 MW 800 MWSubcritical
170 ata / 537 °C / 537 °C
Super Critical247 ata / 565 °C /
593 °C
Imp
rov
em
en
t
4.3 %
9
Steam Power plant efficiency increases with increase in steam pressure and temperature.
Power plant Cycles operating above critical pressure (221.2 bar) are classified as Supercritical cycles
With higher cycle efficiency, the supercritical cycle offers the advantage of ‘burn less fuel for the same output’ and lower emission.
Supercritical Cycles
Lesser Pollutants – SOX , NOX & CO2
10
IMPROVEMENT IN EFFICIENCY WITH INCREASING INLET PARAMETERS FOR STEAM TURBINES
11
PARAMETERS UNIT 500 MW 660 MW 800 MW
MS PRESSURE ATA 170 247 247
MS TEMPERATURE oC 537 565 565
MAIN STEAM FLOW T/HR 1500 1919 2380
REHEAT PRESSURE ATA 40.5 56 60
RH TEMPERATURE oC 537 593 593
FINAL FEED WATER TEMP.
oC 253 290 290
PARAMETERS FOR BHEL STEAM TURBINES
12
Typical Supercritical TG Cycle
13
REGENERATIVE CYCLE CONFIGURATION
• TWO EXTRACTIONS FROM IPT
• FOUR LP HEATERS
• DEAERATOR
• ONE EXTRATION FROM HPT
• THREE HP HEATERS
• 250% TURBINE DRIVEN BFP
• ONE MOTOR DRIVEN BFP
14
STEAM TURBINE MODULE CONFIGURATION
MODULE 500 MW 660 MW 800 MW
HP TURBINE H30-100 H30-100 H30-100
IP TURBINE M30-63 M30-100 M30-100
LP TURBINE N30-2 x 10 N30-2 x 12.5 N30-4 x 8
HP VALVES 2 x FV320 2 xFV250A 2 xFV250A
IP VALVES 2xAV560 2xAV560A 2xAV560A
15
16
660MW Steam turbine: With Supercritical parameters
Order for 2x660 MW Barh- II/ DB Power & 3 x 660 Bara & Lalitpur TPPOther expected tenders 1 x 660 MW JITPL Angul, Jhabua Seoni, etc
Salient Feature:
• New series of HP & IP modules for supercritical parameters• Higher size LP module
247 ata Main Steam Pressure565 0C Main Steam Temperature593 0C Hot reheat Temperature
• Impulse tilted blade in HP & IP turbines
• Heat Shield at the inlet section
• Increase in wall/pipe thickness
• Material with improved properties for higher steam temperature
• Optimum flow path
17
18
800MW Steam turbine
Salient features:• 4 cylinder turbine (2 LP’s)• New series of HP, IP & LP modules for super critical parameters
HP Turbine
LP Turbine 1 LP Turbine 2
IP Turbine
Condenser
Generator
Orders for Yermarus (2x800 MW), & Edlapur (1x800 MW), JV between KPCL and BHELOrder expected for NTPC 2 x 800 MW Gajmara TPP & Udangudi (2x800 MW), JV between TNEB and BHEL
19
800MW Steam turbine:
General Arrangement
20
CROSS SECTIONAL ARRANGEMENT OF 800 MW STEAM TURBINE
FOUR CYLINDER TURBINE
21
CONSTRUCTIONAL FEATURES OF HP TURBINE FOR 800 MW
• SINGLE FLOW, DOUBLE SHELL• OUTER CASING BARREL TYPE IN TWO PIECES• INNER CASING AXIALLY SPLIT• MONO BLOCK DRUM TYPE ROTOR
Barrel in two pieces
22
CONSTRUCTIONAL FEATURES OF IP TURBINE FOR 800 MW
• DOUBLE FLOW, DOUBLE SHELL CASING• MONO BLOCK DRUM TYPE ROTOR • STEAM ADMISSION IN L/H FROM BOTH SIDES• EXTRACTIONS CONNECTIONS IN LOWER HALF ONLY• VALVES BOLTED TO THE CASING IN LOWER HALF
23
HPT FIRST STAGE
Diagonal Impulse Blading
24
IP Turbine : HEAT SHIELD WITH VORTEX BORES
25
• DOUBLE FLOW, DOUBLE SHELL• OUTER CASING FABRICATED , INNER CASING CASTINGS• MONO BLOCK ROTOR
CONSTRUCTIONAL FEATURES OF LP TURBINE FOR 800 MW
26
SECTIONAL DETAILS OF LP TURBINE FOR 660 / 800 MW
27
INNER CASING IS INDEPENDENT OF OUTER CASING
INNER CASING RESTS ON OUTER CASING
660 MW500 MW
LP TURBINELP TURBINEDIFFERENCES IN CONSTRUCTIONAL FEATURES DIFFERENCES IN CONSTRUCTIONAL FEATURES
500 MW V/S 660 MW500 MW V/S 660 MW
28
SECTIONAL DETAILS OF LP TURBINE FOR 660 / 800 MW
29
PUSH ROD ARRANGEMENT
30
LP TURBINE INNER CASING SUPPORT DETAILS FOR 660 / 800 MW
31
THROTTLE CONTROLLED GOVERNING WITH
HIGH PRESSURE ELECTRO HYDRAULIC COMPACT ACTUATORS (160 BAR)
GOVERNING
32
NEW DESIGN(660 MW)
THROTTLE GOVERNINGHIGH PRESSURE ELECTRO HYDRAULIC GOVERNING(ACTUATORS WITH PRESSURE OF 160 BAR)
Turbine Governing
EXISTING DESIGN(500 MW) THROTTLE GOVERNINGELECTRO HYDRAULIC(WITH 32 BAR PRESSURE)
33
Turbine Governing ADVANTAGES OF EHA BASED SYSTEM
• Simplified plant layout due to overall compact size
• Control oil piping reduced• Faster response due to state of art
electronic control and protection system • Better interconnection with other system• Ease of operation and maintenance
• Valve room is avoided
34
Turbine GoverningEHA SYSTEM CONSISTS OF
* HYDRAULIC POWER SUPPLY UNIT* HPSU CONTROL UNIT* VALVES ACTUATORS* CONTROLLERS* PROTECTION SYSTEMS
35
OVERHAULING
36
SUMMARY
• Proven Supercritical technology in collaboration with M/s Siemens
• Steam Parameters up to 300 bar / 600°C / 620°C
• Modular Turbo set design to fit best customer needs
• High reliability & Availability
• Long Inspection intervals
• High efficiency by using modern CFD tools for flow path & blades
37
Thank you for a Patient hearing…………