1 ISAT 413 - Module III: Building Energy Efficiency Topic 1: Gas Mixtures, P-v-T Behavior...
-
Upload
jamil-thistle -
Category
Documents
-
view
227 -
download
2
Transcript of 1 ISAT 413 - Module III: Building Energy Efficiency Topic 1: Gas Mixtures, P-v-T Behavior...
1
ISAT 413 - Module III: Building Energy Efficiency
Topic 1: Gas Mixtures, P-v-T Behavior
Introduction to Building Energy Efficiency
Gas Mixtures
P-v-T Behavior
2
Introduction
“Energy use in buildings accounts for 35% of the total primary energy consumption in the United States and 42% of the total energy costs, and produces 35% of all U.S. carbon emissions. Utility bills are a substantial part of a family budget, so residential energy efficiency affects the kinds of housing people can afford as well as their comfort level. …. Energy savings can be achieved simultaneously with overall enhancement of indoor air quality, occupant comfort, and work productivity.…”
(Quoted from CRC Handbook of Energy efficiency, 1994)
3
Building Energy Efficiency Standards
The NAECA (National Appliance Energy Conservation Act) minimum standard for the major types of equipment in the residential sector are:
Heat Pumps—A 10.0 minimum SEER for 1992 Room Air Conditioners—An 8.6 EER in 1990 Gas/Oil Furnaces—A 0.78 annual fuel utilization efficiency in 1992 Refrigerator—A standard of 691 kWh/year in 1993 Electric Water Heaters—A 0.88 Energy Factor in 1990 Natural Gas Water Heaters—A 0.54 Energy Factor in 1990
(From CRC Handbook of Energy Efficiency, 1994)
4
EER (Energy Efficiency Ratio):
What is SEER (Seasonal Energy Efficiency Ratio)?
kW
hrBtuEER
in Input Power
/ in Output Power14~10
237188506271308710 ..EER.~.SEER Temperature and humidity control are two key components of space conditioning. The temperature of the atmospheric air in air-conditioning applications ranges from about -10 to 50oC, i.e., air and water-vapor behavior very like ideal gas.
Two Common Terms Used in the Domestic Heating and cooling
5
CHPF (Combined Heating Performance Factor):
CCPF (Combined Cooling Performance Factor):
kWWWW
Btu/hrQQ~CHPF
whahuhp
sh
in
in wtk
84
kWWWW
Btu/hrQQ~CCPF
whahuhp
sc
in
in wtk
106
Another Two Common Terms Used in the Domestic Heating and cooling: (for integrated systems)
6
Energy-Efficient Appliances
Vacuum panel insulation refrigerators
EPRI/e-tech heat pump (http://www.aers.com/heatpump.html)
Integrated water heater and condensing gas furnaces (http://oee.nrcan.gc.ca/publications/infosource/pub/home/Heating_With_Gas_Chapter3.cfm?attr=4)
Air-source variable-speed heat pump
Ground-source two-speed heat pump
Electronic ignition for gas ranges
Heat pump dryers
7
A mixture of two or more gases of fixed chemical composition is called a nonreacting gas mixture. The composition of a gas mixture is described by specifying either the mole fraction or the mass fraction of each component, defined as
where
Gas Mixtures
8
The apparent (or average) molar mass and gas constant of a mixture are expressed as
and
9© The McGraw-Hill Companies, Inc.,1998
Dalton’s Law of Additive Pressures for the Mixture of Two Ideal GasesDalton’s Law of Additive Pressures for the Mixture of Two Ideal Gases
,BAm PPP if it existed alone at the mixture temperature and volume.
P-v-T Behavior of Gas Mixtures
10
Amagat’s Law of Additive Volumes for
the Mixture of Two Ideal Gases
Amagat’s Law of Additive Volumes for
the Mixture of Two Ideal Gases
,BAm VVV if it existed alone at
the mixture temperature and pressure.
11
Dalton's law of additive pressures states that the pressure of a gas mixture is equal to the sum of the pressures each gas would exert if it existed alone at the mixture temperature and volume.
Amagat's law of additive volumes states that the volume of a gas mixture is equal to the sum of the volumes each gas would occupy if it existed alone at the mixture temperature and pressure.
12
Dalton's and Amagat's laws hold exactly for ideal-gas mixtures, but only approximately for real-gas mixtures. They can be expressed as
Dalton's law:
Amagat's law:
k
i
mmim PTVV1
,
13
Here Pi is called the component pressure and Vi is called the component volume. Also, the ratio Pi/Pm is called the pressure fraction and the ratio Vi/Vm is called the volume fraction of component i. For ideal gases, Pi and Vi can be related to yi by
The quantity yiPm is called the partial pressure and the quantity yiVm, is called the partial volume.
14
Compressibility Factors: One Way of Predicting Real-Gas Mixture P-v-TCompressibility Factors: One Way of Predicting Real-Gas Mixture P-v-T
Zi is the compressibility of each real gas component in the mixture (refer to Figure A.12)
15
The P-v-T behavior of real-gas mixtures can be predicted by using generalized compressibility charts. The compressibility factor of the mixture can be expressed in terms of the compressibility factors of the individual gases as
where Z is determined either at Tm and Vm, (Dalton's law) or at Tm and Pm (Amagat's law) for each individual gas.
16
Another Way of Predicting the P-v-T Behavior of a Real-Gas MixtureAnother Way of Predicting the P-v-T Behavior of a Real-Gas Mixture
Treat a real-gas mixture as a pseudopure substance with critical properties P´cr and T´cr
17
The P-v-T behavior of a gas mixture can also be predicted approximately by Kay's rule, which involves treating a gas mixture as a pure substance with pseudocritical properties determined from
and
18
The evaluation of intensive properties of a gas mixture involves averaging in terms of mass or mole fractions (e.g. pressure, temperature, and density). The extensive properties of a gas mixture, in general, can be determined by summing the contributions of each component of the mixture (e.g. mass, volume, weight, energy, enthalpy, and entropy). :
k
i
k
i
k
i
iiiiim
k
i
k
i
k
i
iiiiim
k
i
k
i
k
i
iiiiim
sNsmSS
hNhmHH
uNumUU
1 1 1
1 1 1
1 1 1
(kJ/K)
(kJ)
(kJ)
19
and
20
Use of Partial Pressures for Entropy EvaluationUse of Partial Pressures for Entropy Evaluation
Partial pressures (not the mixture pressure) are used in the evaluation of entropy changes of ideal-gas mixtures