1

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

GBC Pull UP Banner

Instruction

2

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

Content

Printing Image for Pull Up Banner ............................................................................................ 3

Applying Image to Pull Up Banner ......................................................................................... 12

Packing the Banner stand ......................................................................................................... 18

3

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

Printing Image for Pull Up Banner

1) Customer to set up job based on the following specification:

Printable area: 830mm x 2000mm

Make sure the first 20mm of the printable area does not have any

important text or image as this area will be covered.

Allow 250mm to be hidden inside the roller of the display stand which is

not visible

830mm

250mm

2000mm

Blank inside display stand

2250mm

4

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

2) From any appropriate application, eg. PDF or Photo software, select File => PRINT

3) Select Canon IPF8000s under Name, and select PROPERTIES

5

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

4) Select PAGE SETUP, then go to PAGE SIZE and select OW BANNER

5) Under LAYOUT tab, select PAGE LAYOUT and select FREE LAYOUT

6

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

6) Select OK when the message below show up

7) Select OK

8) Select OK again to print

7

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

9) ImagePROGRAF FREE LAYOUT screen will appear.

10) Select FILE => DETAILED SETTINGS.

Under MAIN tab, select Glossy Photo Paper for media type and POSTER

(PHOTOS) or POSTER (TEXT) for print target.

8

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

11) Select PREFERENCE

12) Select mm for units.

9

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

13) Select PAGE SETUP tab, and select ISO A0/A1 Roll(841.0mm) for ROLL PAPER

WIDTH and NO for AUTOMATIC CUTTING

14) Select OBJECT SETTINGS tab, and select NONE for OBJECT FRAME STYLE

10

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

15) You are now ready to move the image into position and modify the size by dragging

the image at the corner.

Drag the image in order to line up the width at 830mm wide (see arrow)

16) Make sure there is no text or important graphics passing the 2000mm mark. Anything

passed the 2000mm mark will be hidden inside the roller of the display stand

11

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

17) Click print icon, and select OK

18) After the image is printed, click ONLINE to go OFFLINE, and then hold down the

DOWN ARROW BUTTON to manually feed the media out (approximately

200mm).

19) Perform FORCE CUTTING. Choose MENU => PAPER CUTTING => YES

12

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

Applying Image to Pull Up Banner

1) Pull both end cap off the top bar

2) Pull top bar apart to give a gap

13

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

3) Slide the top of the print into the gap of the top bar. Making sure the smooth surface is

facing up

4) Lock the top bar by pushing the bar down

14

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

5) Put both end cap back into the top bar

6) Place the bottom part of the banner stand at the bottom of the print as below and peel

off the backing from one side of the tape.

15

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

7) Stick the printed image on to the tape

8) Peel the rest of the backing of the tape and place the remaining printed image onto the

tape

16

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

9) Pull the pin from the right hand side of the banner stand, making sure that you place

ONE hand on the image.

10) Let go of the image slowly, making sure that the image retract into the banner stand

straight, and preventing the edge of the image getting damaged.

11) Place one end of the rod into the hole on the banner

17

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

12) Grab the hook on the top bar and pull it up

13) Place the hook into the top end of the rod

14) Swing the legs of the banner stand out

18

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

Packing the Banner stand 1) Swings the legs of the banner stand back

2) Unhook the top bar with the rod. IF you cannot reach the top bar, pull the banner

down in an angle.

19

GBC Australia

Created By: Jimmy Nguyen 1800 422 349

15) One hand hold the rod, the other hand drop the image into the banner stand slowly

16) Pull the rod out of the hole on the banner stand

17) Pack all the accessories into its original black bag

Note: Always make sure you put the banner stand together before packing them up for the

clients.