1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning...
-
Upload
devin-vickerman -
Category
Documents
-
view
233 -
download
2
Transcript of 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning...
![Page 1: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/1.jpg)
1
Circuit Design and Examples
•Design Guidelines–Objectives–Sensor–Signal Conditioning
•Example•Instrumentation Amplifiers
–AD620
•OpAmps–Op07 (modern)–LM741 (ancient)
![Page 2: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/2.jpg)
2
Design Guidelines-1
• Define the measurement objective– Parameter: What do you need to measure:
pressure, temperature, flow, level, etc– Range: What is the range of the measurements?
50-1500 F, 25-65 psi, 100-200 volts– Accuracy: What accuracy is desired and what
specification of accuracy will be used? 5% of Full Scale or 2% of the reading.
– Linearity: Must the measurement be linear?– Noise: How much noise is allowed?
![Page 3: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/3.jpg)
3
Design Guidelines-2• Select the sensor/transducer
– Parameters: What is the input and output of the transducer? E.g. pressure in resistance out, temperature in voltage out, light in current out
– Transfer Function: Output/input relationship?– Time Response: 1st order, 2nd order?– Range: What is the possible range of sensor parameters? 0-
1000C, 3-15 psi, etc– Power: What is the power specification of the sensor?
Sensor Definition in Engineering: the component of an instrument that convertsan input signal into a quantity that is measured by another part of the instrumentand changed into a useful signal for an information-gathering system.
A transducer is an electronic device that converts energy from one form to another. Common examples include microphones, loudspeakers, thermometers, position and pressure sensors, and antenna. Although not generally thought of as transducers, photocells, LEDs (light-emitting diodes), and even common light bulbs are transducers.
![Page 4: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/4.jpg)
4
Design Guidelines-3
• Analog Signal Conditioning– Parameter of output? Voltage, current,
pressure, frequency– Range? 0-5V, 3-15psi, 4-20mA, 300-3500 Hz– Input impedance of the signal conditioning
circuit? Many sensors require a specific impedance input or a range of allowable inputs
– Output impedance to the next stage?
![Page 5: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/5.jpg)
5
Example: Problem 2.33 in textMy solution (check the solution manual for the author’s solution)
2.33: A bridge circuit has R1=R2=R3=120 ohms and V=10.0 volts. Design a signal conditioning system that provides an output of 0 to 5 volts as R4 varies from 120 to 140 ohms. Plot Vout vs R4. Evaluate the linearity
AA B
Desired output is VA-B
![Page 6: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/6.jpg)
6
How to create a graph with
a varying resistance
AA B
1. Place a normal resistor as R4.2. Double click on the value of the
resistance3. Enter {Rvar} [Yes the braces are
required]4. Go to “Get New Part” in the Draw Menu5. Place the part name “PARAM” on the
schematic page6. Double click on Parameters7. Enter Rvar as Name1
And Value1=100
8. Go to Analysis/Setup menu9. Check and open the DC
Sweep box10.Check Global Parameter and
Linear11.Enter the Name of the variable Which is Rvar here, the start and end values of the sweep and the increment for the sweep12. Simulate
10
![Page 7: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/7.jpg)
7VA-VB
)42
4
31
3(10
RR
R
RR
RVV BA
A B
![Page 8: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/8.jpg)
8
VA-VB
A B
0 to .3846 to 0 to 5Requires a gain of5/.3846=13.0
![Page 9: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/9.jpg)
9
Need Differential Gain of 13
![Page 10: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/10.jpg)
10
Instrumentation AmplifiersAnalog Devices Inc. is the largest supplier of instrumentation amplifiers in the world.The AD620 is a low cost, high accuracy instrumentation amplifier which requires only one external resistor to set gains of 1 to 1000. Furthermore, the AD620 offers lower power (only 1.3 mA max supply current), making it a good fit for battery powered, portable (or remote) applications.
The AD620, with its high accuracy of 40 ppm maximum nonlinearity, low offset voltage of 50 µV max and offset drift of 0.6 µV/°C max, is ideal for use in precision data acquisition systems, such as weigh scales and transducer interfaces. The low noise, low input bias current, and low power of the AD620 also make it well suited for medical applications such as ECG and noninvasive blood pressure monitors.
The low input bias current of 1.0 nA max is made possible with the use of Superbeta processing in the input stage. The AD620 works well as a preamplifier due to its low input voltage noise of 9 nV/Hz at 1 kHz, 0.28 µV p-p in the 0.1 Hz to 10 Hz band, 0.1 pA/µHz input current noise. The AD620 is also well suited for multiplexed applications with its settling time of 15 µs to 0.01% and its cost is low enough to enable designs with one in amp per channel.
![Page 11: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/11.jpg)
11
AD620 Specifications
http://products.analog.com/products/info.asp?product=AD620
common-mode rejection ratio (CMRR): The ratio of the common-mode interference voltage at the input of a circuit, to the corresponding interference voltage at the output.
![Page 12: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/12.jpg)
12
Electrostatic Warning for the AD620 In-Amp
![Page 13: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/13.jpg)
13
AD620 vs opamp
Make vs. Buy: A Typical Bridge Application Error BudgetThe AD620 offers improved performance over “homebrew”
three op amp IA designs, along with smaller size, fewer components and lower supply current. In the typical application, a gain of 100 is required to amplify a bridge output of 20 mV full scale over the industrial temperature range of –40°C to +85°C.
Regardless of the system in which it is being used, the AD620 provides greater accuracy, and at low power and price.
Note that for the homebrew circuit, the OP07 specifications for input voltage offset and noise have been multiplied by 2, because a three op amp type in-amp has two op amps at its inputs.
![Page 14: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/14.jpg)
14Error Budget
![Page 15: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/15.jpg)
15Op07 vs LM741
• The OP-07 has very low input offset voltage (25µV max for OP-07A) which is obtained by trimming at the wafer stage. These low offset voltages generally eliminate any need for external nulling. The OP-07 also features low input bias current (±2nA for OP-07A) and high open-loop gain (300V/mV for the OP-07A). The low offsets and high open-loop gain make the OP-07 particularly useful for high-gain instrumentation applications.
• The wide input voltage range of ±13V minimum combined with the high CMRR of 110dB (OP-07A) and high input impedance provides high accuracy in the non-inverting circuit configuration. Excellent linearity and gain accuracy can be maintained even at high closed-loop gains.
• The OP-07 is available in five standard performance grades.
The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications.
![Page 16: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/16.jpg)
16
Op07 vs 741
(Inexpensive versions of each)
Op07 (Analog Devices)
LM741 (National Instruments)
Input Offset Voltage
30 to 75 uV 6 to 7.5 mV
Input Offset Current
.4 to 2.8 nA 200 to 300 nA
CMRR 110 dB Min 70 dB Min
Closed Loop BW (gain = 1)
.6 MHz .437 MHz
Slew Rate .3 V/uSec .5 V/uSec
$0.44 for one LM74125 for $8
$1.25 for one Op0725 for $25
From Digikey
![Page 17: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/17.jpg)
17
Summary
• Design Guidelines– Objectives– Sensor– Signal Conditioning
• Example• Instrumentation Amplifiers
– AD620
• OpAmps– Op07 (modern) from Texas Instruments, Linear
Technology, or Maxim– LM741 (old but useful) from National Semiconductor
![Page 18: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/18.jpg)
18
Digital Signal Conditioning•AC Bridges
•Number systems
•Boolean Algebra Example
•Tristate Buffers
•Comparators and Circuits
•Schmidt Trigger
•Window Detector
![Page 19: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/19.jpg)
19
AC Bridge Circuits
Generalized AC Bridge
Balanced when:Z1Zx = Z2Z3
A B
![Page 20: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/20.jpg)
20Wien Bridge
)1()
1(
33
321 RCj
RR
CjRR
xx
R1 R2
R3
Rx
C3
Cx
Condition for Balanced Bridge
![Page 21: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/21.jpg)
21
Wien Bridge Oscillator Circuithttp://niuhep.physics.niu.edu/~eads/phys475/lab9.html
.001 uF
.001 uF
10KΩ10KΩ
Adjust the 50K resistorfor a sine wave output
Expected Sine WaveFrequency=15.9 KHz
![Page 22: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/22.jpg)
22
AC Bridges
http://chem.ch.huji.ac.il/~eugeniik/instruments/test/bridges_theory.html
![Page 23: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/23.jpg)
23
Number Systemshttp://www.ibilce.unesp.br/courseware/datas/data1.htm
BITSA bit is the smallest element of information used by a computer. A bit holds ONE of TWO possible values: 0 meaning Off/False/NotSet and 1 meaning On/True/Set
Boolean ValuesBoolean algebra recognizes True and False. So a single bit can represent a Boolean variable.
NIBBLEA nibble is a group of FOUR bits. This gives a maximum number of 16 possible different values. 2 ^ 4 = 16
LSB and MSB:The Least Significant Bit (LSB) is always drawn at the extreme right and has the least value and the Most Significant Bit (MSB) is always shown on the extreme left, and is the bit with the greatest value.
![Page 24: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/24.jpg)
24Number Systems
BYTESBytes are a grouping of 8 bits. This comprises TWO nibbles.
Binary Coded Decimal [BCD]Binary code decimal digits (0-9) are represented using FOUR bits. The valid combinations of bits and their respective values are 0000 through 1001 with the binary combinations 1010 to 1111 not used. If the computer stores one BCD digit per byte, its called normal BCD. The unused nibble may be all 0's or all 1's.
Packed BCD:If two BCD digits are stored per byte, its called Packed BCD. This occurs in data transmission where numbers are being transmitted over a communications link. Packed BCD reduces the amount of time spent transmitting the numbers, as each data byte transmitted results in the sending of two BCD digits.
![Page 25: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/25.jpg)
25
Number SystemsHexadecimal
Refers to the base-16 number system, which consists of 16 unique symbols: the numbers 0 to 9 and the letters A to F. e.g. decimal 15 is represented as F in hexadecimal. This is useful because it can represent a byte (8 bits) as two hexadecimal digits. It is easier to read hexadecimal numbers than binary numbers.
To convert a value from hexadecimal to binary, translate each hexadecimal digit into its 4-bit binary equivalent. Hexadecimal numbers have either an 0x prefix or an h suffix. For example, the hexadecimal number 0x3F7A translates to the following binary number: 0011 1111 0111 1010
http://www.webopedia.com
![Page 26: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/26.jpg)
26
Multiplication/Division
• Multiplication by 10: Shifting left in decimal multiplies by 10. E.g. 05010 50010
• Multiplication by 2: Shifting left in binary multiplies by 2. E.g. 01002 10002 which translates to 410 810
• Division works the same way in that shifting right divides by 10 in decimal, 2 in binary, 8 in octal, and 16 in hexadecimal.
![Page 27: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/27.jpg)
27
Push-On Push-Off Control Circuithttp://www.oldradio.com/current/pushon-pushoff.htm
Push-ButtonSwitch
Relay Coil
24 volt dcN.C.
N.O.
![Page 28: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/28.jpg)
28
Example
VisionSystem
D
Wt SensorA
IR SensorB
Robot WelderC
A B C D
0 0 0 0
0 0 0 1
0 0 1 0
0 0 1 1
0 1 0 0
0 1 0 1
0 1 1 0
0 1 1 1
1 0 0 0
1 0 0 1
1 0 1 0
1 0 1 1
1 1 0 0
1 1 0 1
1 1 1 0
1 1 1 1
A
B
D
C
AB
CD
ABCD
Nand
Nand
A + B
C + D
![Page 29: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/29.jpg)
29
Tri-state Buffers
http://www.websdeveloped.com/Billy/ComputerOrganization/Assignments/2/Assignment2.htm
1
1
Enable
![Page 30: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/30.jpg)
30
Comparators
http://para.maxim-ic.com/Comparators.htm Maxim
http://www.national.com/catalog/AnalogComparators.html
National Semiconductor
Fairchild Semiconductor
Fairchild
http://amplifier.ti.com
Texas Instruments
![Page 31: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/31.jpg)
31
National Semiconductor LM111 Comparator:
(LM311 is $0.52 each at Digikey)
http://www.national.com/pf/LM/LM111.html
http://www.chipcenter.com/images/tn026.pdf
Article on the meaning of Rail-to-rail
Open-drain outputs are outputs which at any given time are either actively sinking
current (i.e., low voltage, typically considered logic 0) or are high impedance,
but which never source current (high voltage, logic 1). Open-drain refers to the
drain terminal of a MOS FET transistor. The equivalent concept on a bipolar device is
called open-collector.
http://www.brouhaha.com/~eric/pic/open_drain.html
![Page 32: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/32.jpg)
32Comparator Circuit
http://home.cogeco.ca/~rpaisley4/Comparators.html
A
B
![Page 33: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/33.jpg)
33
Zero Crossing Detector
http://www.national.com/ads-cgi/viewer.pl/ds/LM/LM139.pdf
LM339 is $0.52 at Digikey
![Page 34: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/34.jpg)
34
Schmidt Trigger Circuit
2.5 +2.5Sin(2π*100*t)
100 Hz Sinusoid
![Page 35: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/35.jpg)
35Schmidt Trigger
Switches Low Switches High
![Page 36: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/36.jpg)
36Window Detector
http://webug.physics.uiuc.edu/courses/phys344/344exp/Lab1Analog_Digital/Archive/Su2000/lab1.htm#Part_5_Window_Comparator
![Page 37: 1 Circuit Design and Examples Design Guidelines –Objectives –Sensor –Signal Conditioning Example Instrumentation Amplifiers –AD620 OpAmps –Op07 (modern)](https://reader036.fdocuments.net/reader036/viewer/2022062407/56649c785503460f9492d111/html5/thumbnails/37.jpg)
37
Summary
• AC Bridges
• Number systems
• Boolean Algebra Example
• Tristate Buffers
• Comparators and Circuits
• Schmidt Trigger
• Window Detector