1-2002 Outdoor sulphur Hexafluoride circuit-Breaker · Low filling pressure respect to a pure...
Transcript of 1-2002 Outdoor sulphur Hexafluoride circuit-Breaker · Low filling pressure respect to a pure...
ABB
T&D
Div
isio
ne S
ace
T.M
.S.
-01.
05.1
5 -
OHBOutdoorsulphur Hexafluoride circuit-Breaker
1-2002
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 2
OHB outdoor circuit-breaker
Fields of application outdoor installations control and protection of distribution lines control and protection of distribution substations control and protection of transformers control and protection of capacitor banks
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 3
OHB outdoor circuit-breaker
Electrical characteristics Rated voltage 24 36 kV Withstand voltage (1 min.) 70 (60) 95 (80) kV dry (wet) Impulse withstand voltage 150 200 kV Rated normal current at 40°C 1250 / 2500 A Rated frequency 50 / 60 Hz Rated breaking capacity 25 / 31.5 kA Making capacity 63 / 80 kA Operating temperature -30 . . . . + 40 °C
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 4
OHB outdoor circuit-breaker
Standards
IEC 60056 (tested in compliance with the prescriptions of Amendment 3, table XII, list 1 in order to ensure suitability for overhead lines with rapid re-closing cycle)
IEC 60694
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 5
OHB outdoor circuit-breaker
Development, production, quality control according to :
ISO 14001 STDs as for Environmental Management System
ISO 9001 STDs as for Quality Assurance System
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 6
OHB outdoor circuit-breaker
Features Three Phase Circuit Breaker The same arcing chamber of HD4 MV indoor c.b. series HD4 arcing chamber housed in a hollow porcelain cylinder Ceramic insulators assembled by means of flanges with
terminals Pole cap, flanges, sump in anodized alluminium alloy Pole ”sealed for life” pressure system Pole cover with safety valve Terminal for connection as NEMA 4 form
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 7
OHB outdoor circuit-breaker
Features ESH spring charged operating mechanism (the same actuator
of the whole the HD4 series) Mechanical anti-pumping device to prevent re-closing due to
both electrical and mechanical controls Complete range of accessories Wide range of power supply voltages of the electrical
accessories Two-levels pressure-switch Cabinet housing all the actuator, the control devices, the
operating shafts and lever, the transmission, the poles linkage
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 8
OHB outdoor circuit-breaker
Features Cabinet supporting the three pole assemblies Cabinet and cabinet supporting structure made of hot
galvanised steel sheet Weather proof cabinet Tight door with window for status c.b. inspection without
opening the cabinet door Case door handle suitable for three padlocks Anti-condensation heater and heating elements for low
temperature
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 9
OHB outdoor circuit-breaker
Features CT brackets (on request) ”Closed”, ”Open”, ”Spring charged/discharged”, ”SF6 low
pressure” signalling lamps (on request) Particularly sturdy construction Simple structure requiring minimal preparation of the site Mounting arrangements
Cabinet supported by telescopic supports with adjustable height from 2916 up to 3676 mm (structure in compliance with the prescription of BS 7354 STDs)
Cabinet at ground level
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
0
OHB outdoor circuit-breaker
SF6 interrupter ”Autopuffer” technique based on compression and self-blast
technique Low operating energy thanks to the ”autopuffer” technique Minimal maintenance Life in excess of 10,000 mechanical operations Separation between main and arcing contacts ensuring no wear
of the main contacts Life in excess of 10,000 electrical operations at rated current
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
1
OHB outdoor circuit-breaker
SF6 interrupter Low filling pressure respect to a pure puffer technique Arcing-chamber common to HD4 series (tested arcing-chamber) Pole assembly / ceramic insulators similar to the previous SFE
series (tested solution) Monitoring of the quenching media ”SF6” thanks to the pressure
switch
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
2
OHB outdoor circuit-breaker
1 Terminal2 Insulating enclosure3 Blasting nozzle4 Moving arcing contact5 Moving contact6 Fixed arcing contact7 Fixed contact8 Insulating tie-rod9 Cap with bursting valve
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
3
OHB outdoor circuit-breaker
Breaking technique
M.V. quenching technique based on proven advantages of SF6 ”auto-puffer” H.V. circuit-breaker well-known, tested and used in the major industrialized countries
State-of-the-art SF6 breaking technology
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
4
OHB outdoor circuit-breaker
Autopuffer quenching technique : interruption process
Opening of the main contacts
Opening of the arcing contacts
OpenClose
I I I
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
5
OHB outdoor circuit-breakerThe circuit-breaker is closed
The current flows from the upper (fixed) terminal to the moving part through the main contacts.
I Upper terminal
Main contacts
Arcing contacts
Moving part
Nozzle
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
6
OHB outdoor circuit-breaker
Opening of the main contacts.
The moving part goes down thus separating the main contacts. There is no arc striking as the current keeps flowing from the upper terminal to the moving parts through the arcing contacts. During the downstroke, the moving part exert a pressure on the gas housed in the lower chamber; the pressure increase generated in the lower chamber opens the connection valve of the upper chamber. The compressed gas flows from the lower to the upper chamber thus taking both enclosures at the same pressure level.
I
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
7
OHB outdoor circuit-breaker
Notes:1) no leakage from the nozzle as it is blocked by the fixed arcing
contact
2) no leakage from the cylinder of the moving arcing contact as it is blocked by the fixed arcing contact
3) the upper chamber is connected to the moving mechanism and its volume remains the same during the downstroke (dead volume)
4) the only changing volume is the one of the lower chamber, which decreases during the downstroke of the moving contact
5) this puffer is designed to avoid chopping currents by means of a “dead volume” higher than the compressed volume. As the gas flows towards the upper chamber, the pressure level is equal to the ratio between the dead volume and the lower chamber volume.
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
8
OHB outdoor circuit-breaker
Opening of the arcing contacts
The current keeps flowing due to the arc generated between the fixed and moving contacts. The gas cannot leak either from the nozzle as the hole is blocked by the fixed contact or from the inside of the moving contact because of the arc clogging effect.
I
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 1
9
OHB outdoor circuit-breaker
The breaking chamber undergoes the following process:
at low currents: as the current hits the natural zero and the arc is quenched, the gas flows from the dead volume to the inside of the moving contact. The low pressure guarantees the absence of chopping currents and the small quantity of gas involved is sufficient to restore the dielectric strenght between the two contacts by avoiding, at the same time, the re-strike of the transient recovery voltage.
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 2
0
OHB outdoor circuit-breaker
At higher short circuit currents: the pressure wave of the arc propagates like a supersonic wave, increasing the gas pressure which closes the valve between the two chambers. From this moment on, the device starts working as a pure “self-blast”, the gas overheating and the molecular dissociation due to the high temperature increase the pressure in the dead volume. Said pressure is proportional to the arc and the resulting gas flow guarantees the quenching at the first passage through zero natural current.
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 2
1
OHB outdoor circuit-breaker
Circuit-breaker in the open position
The arc is quenched; the lower chamber reaches its minimum volume and its maximum pressure level, kept by the valve locked by the supersonic wave. As the self-generated pressure of the dead volume decreases, due to the outflow of the gas through the moving contact, the valve re-opens. From now on, a new jet of fresh gas flows in and makes the temperature of the contacts sink. At the same time, the gas flows through the nozzle, free from the fixed arcing contact. The “cleaning” of the arcing chamber by means of fresh gas makes the device suitable for another reclosing and the interruption up to the maximum breaking capacity.
© A
BB T
&D D
ivis
ione
Sac
e T.
M.S
. - 2
2