03 - BreezeMAX - System Architecture CPE - 09-11-16 - Ver

CPE Architecture

Copyright Alvarion Ltd.

2Objectives

Upon completion of this module students will know the following: Subscriber components

Mechanical concept Led indications Specifications

3Subscriber Unit Indoor


The Subscriber Unit (SU) installed at the customer premises

Ports

1 * 10/100BaseT Ethernet

Ethernet 10/100 Mbps

BMAX-CPE-ODU-PRO-

SA-ffBMAX-CPE-IDU-1D

(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

1 * Ethernet "Radio" port to ODU (+DC voltage)

Bridge functionality

Up to 512 MAC addresses behind the SU

The SU is powered from the mains

Indoor

BMAX-CPE-ODU-PRO-

SE-ff

802.11g

PCPC

PC PC

PC

BMAX-CPE-IDU-NG-4D1W(indoor)

For the detailed information of the next slides please refer to theBreezeMAX CPEsProduct Manual



BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C6 5

43

21

7

Indoor

BMAX-CPE-ODU-PRO-

SE-ff

802.11g

PCPC

PC PC

PC


FunctionLabel No

When lit - the SU is connected with an AUWIRELESS LED1

When lit - self test passed and Ethernet connection established with the ODUETH LED2

When lit - SU-IDU power is OKPWR LED3RJ-45 connector supports 10/100 BASE-T and

connected to the customer LANETHERNET Connector4

Ethernet port activity LED when blinking -Ethernet activity at the Ethernet port-5

Ethernet port integrity LED when lit - Ethernet physical layer is OK-6

3 pin AC connector to the AC mains-7



BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

8

Indoor

BMAX-CPE-ODU-PRO-

SE-ff

802.11g

PCPC

PC PC

PC


FunctionLabel NoRJ-45 connector supports 10/100

BASE-T and connects to the SU-ODURADIO

Connector8

Warning: Connecting the radio interface to anEthernet port may damage the equipment

7Networking Gateway (NG)

NG ports: 1 * Ethernet ODU (+ DC voltage) 4 * Ethernet 10/100 BaseT

1 * IEEE 802.11 b/g (AP) Routing functionality

Powered from the mains


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

Powered from the mains

Connects to ODU via a category 5E Ethernet cable:

Ethernet data

Power (54 VDC) Control signals to ODU

Status indications from ODU

Designed for remote management using either internal web server or SNMP

Indoor

BMAX-CPE-ODU-PRO-

SE-ff

802.11g

PCPC

PC PC

PC



5678910

2 431


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

FunctionLabel No

Indoor

BMAX-CPE-ODU-PRO-

SE-ff

802.11g

PCPC

PC PC

PC


FunctionLabel NoOn - the ODU port is connected to the ODU

Blinking - the ODU port is sending or receiving dataODU

LINK/ACT1

On - An active station is connected to the corresponding LAN port

Blinking - The corresponding LAN port is sending or receiving data

LAN LINK/ACT2

On - A printer is connected to the USB portBlinking - The USB port is sending or receiving

data USB3

On - Power is OKPOWER4Used to reset the unit or to set the unit to factory

defaultRESET

BUTTON5

Blinking - Wireless LAN port sending or receiving dataWLAN6


5678910

2 431


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

FunctionLabel No

Indoor

BMAX-CPE-ODU-PRO-

SE-ff

802.11g

PCPC

PC PC

PC


FunctionLabel NoBlinking - The unit functioning properlySTATUS7

Off - Data rate is 10 Mbps on the corresponding LAN port

On - Data rate is 100 Mbps on the corresponding LAN port

LAN SPEED 10/100

8

Off - Data rate is 10 Mbps on the ODU port On - Data rate is 100 Mbps on the ODU port

ODU 10/1009

On - The ODU is connected with an AU WLINK10

10Networking Gateway (NG)Ethernet

10/100 MbpsBMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

FunctionLabel No

56

2 431

Indoor

BMAX-CPE-ODU-PRO-

SE-ff

802.11g

PCPC

PC PC

PC


FunctionLabel No

An SMA connector for the WLAN antenna Antenna Port1

LAN ports for networked computers and other devices

Ports 1-42

Connection to the ODU. Carries Ethernet, Power (55 VDC) and signaling ODU3

DC Power Inlet from Power Transformer POWER4

Used to reset the ODURESET ODU5

USB port to connect a printerUSB6

11Subscriber Unit Outdoor PRO-S CPE

Contains the modem, radio, data processing and management components

Utilize Intel WiMAX Connection 2250 Rosedale 2 802.16e (mobile WIMAX)- ready SDRAM 32M / Flash 16M

The Air Protocol Detection (APD) support automatic switching to the appropriate air protocol, allowing simple upgrade to mobile WiMAX.

Contains an integral high-gain flat antenna or a connection to an external antenna


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

connection to an external antenna

Antenna characteristics

Gain - 13dBi (2.3Ghz), 14dBi (2.5Ghz), 17dBi (3.5Ghz), 16.5 (3.3Ghz)

Azimuth BW - 23(2.x), 20(3.x) Elevation BW - 27(2.x), 20(3.x)

Support all bands

Contains SAU connector

Output power (at antenna port) 19 1 dBm Supports both vertical and horizontal polarizations,

depending on the way it is installed

Indoor

802.11g

PCPC

PC PC

PC


BMAX-CPE-ODU-PRO-

SE-ff

12Subscriber Unit Outdoor - PRO CPE S


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

21

Indoor

802.11g

PCPC

PC PC

PC


BMAX-CPE-ODU-PRO-

SE-ff

FunctionLabel NoUSB connector to connect Subscriber

Alignment UnitSAU

Connector1

RJ-45 connector supports 10/100 BASE-T and connects to the SU-ODU

IDU COM Connecter2

13Subscriber Alignment Unit (SAU)Ethernet



(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

4

1

2

3

Indoor

802.11g

PCPC

PC PC

PC


BMAX-CPE-ODU-PRO-

SE-ff

FunctionLabel NoWhen lit - SU-ODU failureALARM LED1

When lit - SU-ODU power is OKPWR LED2When lit - self test passed and Ethernet connection established with the ODUETH LED3

Wireless link status and signal quality Indication LINK QUALITY

Bar Display4

14Subscriber Alignment Unit (SAU)

The link quality bar display consists of ten LEDs as follows


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-CDescriptionLED NumbersWireless link is up

10 9 8 7 6 5 4 3 2 1

WLNK

Indoor

802.11g

PCPC

PC PC

PC


BMAX-CPE-ODU-PRO-

SE-ff

Wireless link is upThe SU is connected and receives services from

the AU (Network Entry completed) 1

5 dB SNR < 10 dBUp to 210 dB SNR < 15 dBUp to 315 dB SNR < 20 dBUp to 420 dB SNR < 24 dBUp to 5

SNR 24 and RSSI < -75Up to 6SNR 24 and RSSI -75Up to 7SNR 24 and RSSI -70Up to 8SNR 24 and RSSI -60Up to 9RSSI -20 (saturation)Up to 10

15New SAU LOK (Led On Key)Ethernet



(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

Unit is not repairable

Unit is not water resistant

Order Options

SAU-LOK 10-Pack

SAU-LOK 1-Pack

Indoor

802.11g

PCPC

PC PC

PC


BMAX-CPE-ODU-PRO-

SE-ff

FunctionLabel When lit - SU-ODU failureALARM LED

When lit - SU-ODU power is OKPWR LEDWhen lit - self test passed and Ethernet connection

established with the ODUETH LED

Wireless link is upThe SU is connected and receives services from the AU

(Network Entry completed) WLNK

Wireless link status and signal quality Indication LINK QUALITY Bar Display

16New SAU LOK (Led On Key)

WLNK

12345678

FunctionLabel

- The SU is not connected with a Base Station.Off

9


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

BMAX-CPE-IDU-NG-4D1W

ALVR-VG-1DnV-C

BMAX-CPE-ODU-PRO-

The link quality bar display consists of ten LEDs as follows

- CPE is connected with a base station.Orange

- Authentication reject. (From version 4.1)The reason is indicated by Link quality LEDS 7-9.

Blinking Orange

- User Name not found / Wrong Password / Maximum number of multiple sessions has been exceeded.

LEDs 7, 8, 9

illuminate

- Duplicate User Name/Common Name in NPU database.LEDs 8, 9 illuminate

- Authentication timeout: the NPU does not have connection to the defined Radius Server(s), or Shared Secret mismatch between the NPU and Radius Server(s).

LED 9 illuminates

Indoor

802.11g

PCPC

PC PC

PC

BMAX-CPE-IDU-NG-4D1W(indoor)ODU-PRO-SE-ff

17New SAU LOK (Led On Key)

FunctionLED Nr. 5 dB SNR < 10 dBUp to 1

10 dB SNR < 15 dBUp to 215 dB SNR < 20 dBUp to 3


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

20 dB SNR < 24 dBUp to 4SNR 24 and RSSI < -75Up to 5SNR 24 and RSSI -75Up to 6SNR 24 and RSSI -70Up to 7SNR 24 and RSSI -60Up to 8RSSI -20 (saturation)Up to 9

Indoor

802.11g

PCPC

PC PC

PC


BMAX-CPE-ODU-PRO-

SE-ff

18Subscriber Unit Outdoor Spec for 2.xGHz

3.5MHz 5MHz

Rate Nr Modulation Bit rate

Sensitivity [dBm] @ PER 1e-2

Bit rate Sensitivity [dBm] @ PER 1e-2

1 BPSK 1.41 Mbps -98 1.92Mbps -96 2 QPSK 2.83 Mbps -95 3.804Mbps -93


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

2 QPSK 2.83 Mbps -95 3.804Mbps -93 3 QPSK 4.204 Mbps -92 5.76Mbps -89 4 QAM 16 5.606 Mbps -89 7.68Mbps -87 5 QAM 16 8.47 Mbps -86 11.52Mbps -84 6 QAM 64 2/3 11.21 Mbps

-81 15.36Mbps -79

7 QAM 64 12.61 Mbps -80 17.28Mbps -78 Indoor

802.11g

PCPC

PC PC

PC


BMAX-CPE-ODU-PRO-

SE-ff

19IDU-ODU Cable

A category 5e Ethernet cable

Carries the Ethernet data between the two units

Carries power (-54 VDC) and control signals to the SU-ODU

Carries status indications from the SU-ODU

The length of the Indoor-to-Outdoor cable, plus


BMAX-CPE-ODU-PRO-


(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ALVR-VG-1DnV-C

The length of the Indoor-to-Outdoor cable, plus the Ethernet cable connecting the SU to the data equipment, should not exceed 100 meters/328 feet

Use only Category 5E cables from approved manufacturers

Indoor

802.11g

PCPC

PC PC

PC


BMAX-CPE-ODU-PRO-

SE-ff

see catalogAlvarion612098Superior Cables LTDH5E-00481HES Cabling SystemsTSM2404A0DSouthbay Holdings Limited 8393204101Teldor

20Subscriber Unit Self Install (SU-Si)

Compact, single box, Indoor CPE Utilize Intel WiMAX Connection 2250

Rosedale 2 (802.16e ready) SDRAM 32M (old 16M) / Flash 16M (old 4M)

SU antenna selection automatic & manual Detach antenna kit and possible mounting

scenarios (window, mounting kit)

Indoor


BMAX-CPE-Si-E-3.5

(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

scenarios (window, mounting kit) Expected coverage is limited than Pro CPE Recommended to install the unit next to a

window facing the BST Ethernet or USB connector Configuration through Smart Card


Contains the modem, radio, data processing and management components

Contains a beam switching array of 6 antennas

All SU-Si types (2.x & 3.x) support all bands Output power (antenna port):

Indoor


BMAX-CPE-Si-E-(indoor)

hub / switch

PC

PC

ALVR-VG-1DnV-C

Output power (antenna port): 21dBm @ 5Ghz

23dBm @ 3.5Ghz

24dBm @ 2.5Ghz

23dBm @ 2.3Ghz Smart CardN/A


8

Indoor



hub / switch

PC

PC

ALVR-VG-1DnV-C

1

FunctionLabel NoStatus IndicationStatus LED1

Indicates the quality of the received signalSIGNAL LEDs2Ethernet port activity LED when blinking - Ethernet activity

at the Ethernet port-3

Ethernet port integrity LED when lit - Ethernet physical layer is OK-4

Reset button removed starting v4.5.1-5DC power jack7.3V DC6

RJ-45 connector supports 10/100 BASE-T or USB connected to the customer LAN

ETHERNET/USB Connector7

Initiating Scanning ModeScan Button8

8

2

1

7

6

3

4

5


Indoor



hub / switch

PC

PC

ALVR-VG-1DnV-C

FunctionStatus LED- CPE is not powered or power failure.Off

- CPE is connected with a base station.Green- CPE failure.Red- After power-up (if power supply is ok) until start of self test, after passing self-test until network entry is completed, or upon Orange until network entry is completed, or upon restarting the network entry process.- CPE is being set to Factory Defaults (during 6 seconds after pressing the RESET button for more than 5seconds).

Blinking Orange

- In case SIGNAL LEDs 5, 6 and 7 are on: Authentication reject by RADIUS server.- In case SIGNAL LEDS 6 and 7 are on: Rejected by Base Station (Duplicate SU Name in database).- In case LED 7 is on: Authentication Timeout, re-authentication failure (connection to RADIUS server lost).

Blinking Green


FunctionLED Nr. 5 dB SNR < 10 dBUp to 110 dB SNR < 15 dBUp to 2

Indoor



hub / switch

PC

PC

ALVR-VG-1DnV-C

10 dB SNR < 15 dBUp to 215 dB SNR < 20 dBUp to 320 dB SNR < 24 dBUp to 4

SNR 24 and RSSI < -75Up to 5SNR 24 and RSSI -75Up to 6SNR 24 and RSSI -70Up to 7SNR 24 and RSSI -60Up to 8RSSI -20 (saturation)Up to 9


Indoor



hub / switch

PC

PC

ALVR-VG-1DnV-C

FunctionLabel

Press for less than 3 seconds:Initiate Best AU selection process without full scanning. It means that the CPE scans only the AUs detected in the last full scan. The LEDs will be blinking scan. The LEDs will be blinking as mentioned above for Best AU operation.

Press for 3 seconds or more:Initiate full scan, prepare an updated the best AU list and select the best AU. The LEDs will be blinking as mentioned above for full scan operation.

Scan Button


The following drawings describes the embedded antennas main beam direction

External antenna is referred as ANT 0

The operational antenna is selected from the SI menus

Indoor


BMAX-CPE-Si-E-3.5

(indoor)hub /

switch

PC

PC

ALVR-VG-1DnV-C

ANT 1 ANT 3

ANT 0


Identification of Rosedale 2 by SU Type (Valid for Si&PRO-S)

Identification of USB/Eth model by Interface Type (USB/Eth)

USB model requires installation of driver that supplied with the unit (Win 98SE,WinME, supplied with the unit (Win 98SE,WinME, Win2K, WinXP, WinXP 64bits)

USB model has two MAC Addresses: MAC A MAC that the PC extracts from

the Si as the PCs USB controller has no MAC (e.g, NIC). This MAC can be viewed in the ARP table of the PC

MAC B The Rosedale MAC used for authentication with the NPU. This MAC is displayed in the SU menu


FREQUENCY RANGE

2.3 - 2.7 GHz

GAIN 9.5 -10.5dBi VSWR 2:1 (max) 3dB AZIMUTH BEAMWIDTH

70 (typ)BEAMWIDTH3dB Elevation BEAMWIDTH

20 (typ)

POLARIZATION Linear VerticalF/B RATIO -20dB (typ)INPUT IMPEDANCE

50 (ohm)

29SU-Si 3.x Window Antenna

FREQUENCY RANGE

3.4 - 3.7 GHz

GAIN 12dBi VSWR 2:1 (max) 3dB AZIMUTH BEAMWIDTH

77 (typ)BEAMWIDTH3dB Elevation BEAMWIDTH

17 (typ)

POLARIZATION Linear VerticalF/B RATIO -18dB (typ)INPUT IMPEDANCE

50 (ohm)

New BreezeMAX Si Business Models

31Smart Card

Plug&Play - The customer just plug the Smart Card to the Si and start to work

The CPE is purchase in a public location

Smart Cards are burnt by the operator

Ver. 09-04-15

burnt by the operator

32Smart Card

Smart Card Writer/Reader Application User Information Tab

Enables to enter the user information necessary for proper authentication

The User Name and Password are editable to the Sales user only. When logged in as Administrator, these parameters are read only

User Name and Password provided by operatorSales Administrator

Ver. 09-04-15

Sales Administrator

33WiMAX Modem Application

An easy to follow InstallShield Wizard On screen instructions Language Selection User Name and Password supplied by

operator Choosing location

Ver. 09-04-15


Management Status Tab Shows network connection

status Graphical display Continuous updates of link

parameters and quality, counters etc.

User name,

Ver. 09-04-15

User name, connection status,

SW ver 1 2 3

1

2

3

Connection between PC and WiMAX Modem

Indication of correct Modem-Base Station definitions

Connection to an authentication mechanism (radius server/NPU)


Management Settings Tab Changeable parameters:

User Info, BS/AU ID, BW, Scanning Freq, Antenna, Rx Atten, Eth port settings.

Customization option

Ver. 09-04-15

Thank You

03 - BreezeMAX - System Architecture CPE - 09-11-16 - Ver

Documents

Transcript of 03 - BreezeMAX - System Architecture CPE - 09-11-16 - Ver