ide:

each line by dividing the length f each line in inches by 96. nd any remainder .

2

3

Stakes

String Line

Marking Paint

Hammer

Ta e Meas re

Sh vel

P st H le Digger

Digging Bar

Circ lar Saw

Drill

Pencil

Wheelbarr w

4’ Level

12” Miter Saw

S eed Sq are

inish N n

T Needed

y dig.

Check al HOA and z ning laws which may reg late the height and

lacement f y r fence.

A ly al ermits as directed by l cal de.

eyes and ears.

Bef re y begin

3

* For standard single gates: (1) small Trex gate panel, (1) steel post insert, and (1) Trex single gate hardware kit.* For standard double gates: (2) large Trex gate panels, (2) steel gate post inserts, and (1) Trex double gate hardware kit.

E ed View

A. 1 P st

B. 1 P st

C. 4 ckets

D. 1 T Rail

E. 19 Pickets

.

4

A

B

C

CC

C

D

E

F

F

G

5

St 1: Determine Install Met

1. S M d: This meth d grad ally “ste s”

the sl e and the rails remain level. This may leave ga s nder the fence. The d nhill st will need t be set taller. nger

sts may be req ired. When laying t the fence

st s acing, meas re n a level line ne st t an ther.

2. ll wing the de: This meth d f ll s the grade r sl e with the rails arallel t the gr . The st acing may need t be red ced t av id rails being t sh rt beca se f the angle.

3. The fence can

di rent height. P st acing will need t be re ced. Pickets will need t be c t t height.

5

ins s that stakes will n t be d rbed when digging h les, and r x. 4-5 inches inside r erty ns t ins re n encr aching n neighb rs.

N tes: Laying t sts 96” 96” centers.

90.2” (68 x 12” = 812” / 9 =90.2” ) n center.

2. string every 96” 2” in fr m the string t mark center f h

St 2: Stake and String

ig. 1

o

6

7

St 3: Dig es

I height begin all end, ere gradechanges) be 74 1/2” inches high**. String a line the

set the the string. (see ig. 4)

4: Set 1. mb and level each st t the string line

4’ level* thatthe are next stringline. with brace ifnecessary

dry 24- .

1. Dig the thestakes the string. The string may be and

are be 12”diameter and 30”

be that they all sides ( ee ig. 2)

This line is lled

set line

is lled t kee the in line.

7

St 5: P sts

Reve l If greaterreve l is desired increase height.

1. set

height ark all end,at 74 1/2”* **

grade and string a line these ( ig. ) ark and height thestring a .

8

9

Using 1 5/8” fence screws, the brackets a bracket* 5 3/4”

the the abracket 73 5/8” ** the

(see ig. ) If the fencea brackets the

be that the rails

angles angleada t rs with the fence brackets.Each a 22.5°

9

5 3/4 “

73 5/8” 74 1/2”

Mark the rail, rail and length by them next the ig. )

the rail with a metal blade. the 1/2” rail

scratching the If the dis-tance between is 91” the rail will be

and rail with miter saw

Slide the rail the rail as the rail the

rackets

10

5.

4.

11

St 8: Install Pickets

Insert the the rail, and it the

at 8’ center, the and last

the rail, their they 1 )

If the last t may be easier the last and reinsert it by sliding it the last

is the (see ig. 1 )

11

12

St 9: Install T R

by atend and the rail

fence bracket the

the rail the fencebrackets 1 5/8” screws the railat each end (see 1 )

1

the (see ig 1 ). the

third the last the and rails with nails screws (see 1 )

12

3 . venly the last (see ig. 1 ) and it the rails

4. Place

1

13

Tre s (all heights)

14

Care And Maintenance Dirt and Debris Clean fence dirt and water and a are all that

needed

Water s, Leaf Staining and W d

Tannins

Sc s & Abras ns

R st Stains, nd-In Dirt and rime and Pigment Staining

Oil and grease Stains

M d & Mildew

Pre re Washer

Sanding Tre m any es n t rec mmend sanding. Sanding will change the a earance f the s rface f Trex Material and will void the warranty.

Dis sal Do not burn Trex d cts.

15

TM

012419