632 South 3rd StreetP.O. Box 2816 � Paducah, KY 42002270-444-0085Fax: 270-443-6180Website: www.matweld.comEmail: customerservice@matweld.com

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

A

B

C

FLOW

5 gpm(19 lpm)

or10 gpm(38 lpm)

PRESSURE

2000 psi(140 bar)

DIMENSIONS

A - 30"B - 13"C - 4"

WEIGHT

49 lbs(23 kg)

The Matweld Spike Puller is alightweight powerful mainte-nance-of-way tool generating13,000 pounds of pulling force. Theefficient design enables the opera-tor to grab the spike from eitherside of the rail without reposition-ing, pull and automatically drop thespike at the top of the stroke inone motion. All moving parts arefully enclosed for safety. The jawscan be changed without specialtools in minutes at the work site.

01100SPIKE PULLER

2

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

3

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

GENERAL SAFETY PRECAUTIONS:TOOL OPERATORS AND MAINTENANCE PERSONNEL MUST ALWAYS COMPLY WITH THESAFETY PRECAUTIONS GIVEN IN THIS MANUAL, AND WITH ALL STICKERS AND TAGS AT-TACHED TO THE TOOL AND HOSE. ALL SAFETY PRECAUTIONS ARE GIVEN FOR YOURSAFETY. READ TO UNDERSTAND AND FOLLOW ALL SAFETY, MAINTENANCE AND OPERA-TION INSTRUCTIONS BEFORE YOU USE OR MAINTAIN THE TOOL. REVIEW THE MANUALDAILY BEFORE USING THE TOOL. IN ADDITION, FOLLOW ALL SAFETY GUIDELINES GIVENYOU BY YOUR SUPERVISOR. DO NOT USE THE TOOL IF YOU HAVE ANY QUESTIONS ABOUTTHE OPERATION, SAFETY OR MAINTENANCE OF THIS TOOL. FAILURE TO FOLLOW THESEINSTRUCTIONS CAN RESULT IN PERSONAL INJURY OR EQUIPMENT DAMAGE.MATWELD HAS NO CONTROL OVER TOOL USE OR OPERATION ONCE IT LEAVES THEMATWELD PLANT. MATWELD HAS NO CONTROL OVER OPERATOR OR MAINTAINER SELEC-TION. THE CUSTOMER MUST ASSUME RESPONSIBILITY FOR THE TOOL�S SUITABILITY FORA PARTICULAR FUNCTION, FOR ANYONE USING THE TOOL OR MAINTAINING THE TOOLREGARDING THEIR FITNESS TO USE THE TOOL OR REPAIR THE TOOL, UNDERSTANDINGOF THE OPERATION AND SAFETY AND MAINTENANCE MANUAL, INTELLIGENCE TO USEGOOD JUDGMENT NECESSARY TO WORK SAFELY AND EFFICIENTLY WITHOUT ENDANGER-ING THEMSELVES OR BYSTANDERS IN THE WORK AREA.� DO NOT OPERATE THE TOOL UNTIL YOU HAVE BEEN THOROUGHLY AND PROPERLY

TRAINED OR UNDER THE SUPERVISION OF AN INSTRUCTOR.� CHECK POWER SOURCE DAILY TO DETERMINE IF CORRECT FLOW AND PRESSURE ARE

AVAILABLE. NEVER EXCEED FLOWS OR PRESSURES FOR THE TOOL BEING USED. PER-SONAL INJURY OR DAMAGE TO THE TOOL CAN RESULT.

� OPERATORS MUST CLEAR THE WORK AREA OF NON-ESSENTIAL PERSONNEL. FLYINGDEBRIS CAN CAUSE SERIOUS INJURY.

� THE OPERATOR MUST BE FAMILIAR WITH ALL PROHIBITED WORK AREAS SUCH AS UN-SAFE GRADES, POOR FOOTING AREAS AND OVERHEAD HAZARDS.

� MAINTAIN BALANCE AND PROPER FOOTING AT ALL TIMES. NEVER OVERREACH TO THEEXTENT THAT A BROKEN PART OR SUDDEN MOVEMENT OF THE TOOL CAN CAUSE YOUTO LOSE YOUR BALANCE AND FALL, OR CAUSE INJURY TO YOUR SELF OR SOMEONEELSE.

4

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

� WHEN WORKING NEAR ELECTRICAL CONDUCTORS, ALWAYS ASSUME THAT THE CON-DUCTORS ARE ENERGIZED AND THAT HOSES AND CLOTHING CAN CONDUCT HARMFULELECTRICITY. USE HOSES LABELED AND CERTIFIED AS NON-CONDUCTIVE.

� DO NOT OPERATE THE TOOL AT EXCESSIVE FLUID TEMPERATURES. OPERATOR DIS-COMFORT AND POTENTIAL BURNS CAN RESULT AT HIGH OIL TEMPERATURES.

� NEVER WEAR LOOSE CLOTHING THAT CAN GET ENTANGLED IN THE WORKING PARTSOF THE TOOLS OR BE CARELESS WITH HANDS, FEET OR OTHER BODY PARTS AROUNDTHE WORKING PARTS OF THE TOOLS. HYDRAULIC TOOLS EXERT HIGH TORQUE ANDFORCE AND CAN CAUSE SERIOUS INJURY OR DEATH IF IMPROPERLY USED.

� TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL TOOL REPAIR, MAINTENANCEOR SERVICE MUST ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY TRAINEDPERSONNEL.

� ALWAYS WEAR SAFETY EQUIPMENT SUCH AS OIL INJECTION RESISTANT WORK GLOVES,SAFETY GLASSES, SAFETY BOOTS, EAR PROTECTION AND OTHER SAFETY APPARELDICTATED BY YOUR SUPERVISOR APPLICABLE FOR THE JOB YOU ARE DOING AND THETOOL YOU ARE USING.

� DO NOT CLEAN, INSPECT, OR REPAIR THE TOOL WHILE CONNECTED TO THE POWERSOURCE. ACCIDENTAL ENGAGEMENT OF THE TOOL CAN CAUSE SERIOUS PERSONALINJURY.

� OIL INJECTION HAZARD EXISTS WITH THIS TOOL. OIL INJECTION IS A CONDITION WHEREHYDRAULIC OIL IS INJECTED UNDER THE SKIN FROM PRESSURE IN THE LINE. ALWAYSWEAR GLOVES AND REPAIR ANY LEAKS IMMEDIATELY. NEVER CARRY A TOOL BY THEHOSES.

� DO NOT USE DAMAGED EQUIPMENT. IMMEDIATELY REPLACE ANY DAMAGED HOSES,FITTINGS, OR OTHER COMPONENTS SHOWING WIRE BRAID, NICKS, CUTS, DAMAGE ORABRASIONS. FAILURE TO DO SO MAY RESULT IN EQUIPMENT DAMAGE AND / OR PER-SONAL INJURY OR DEATH.

� CLEAN UP ANY OIL OR FLUID SPILLS IMMEDIATELY.

5

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

HAVE SUPERVISOR ADD ADDITIONAL PRECAUTIONS RELATING TO THE SPECIFICWORK AREA AND LOCAL SAFETY REGULATIONS BELOW:

**********************

6

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLER

SAFETY PRECAUTIONS:1. ALWAYS WEAR PROTECTIVE EQUIPMENT SUCH AS GLOVES, SAFETY GLASSES, EAR

PROTECTION AND SAFETY SHOES.2. DO NOT WEAR CLOTHING WHICH MAY BECOME ENTANGLED IN THE TOOL.3. ALWAYS KEEP WORK AREA FREE OF TOOLS OR ANY OTHER OBJECTS

WHICH MAY IMPAIR SOUND FOOTING.4. CAUTION OIL INJECTION HAZARD EXISTS WITH THIS TOOL. OIL INJECTION IS A CONDI-

TION WHERE THE HYDRAULIC OIL IS FORCED UNDER THE SKIN THROUGH PRESSUREIN THE LINE. ALWAYS WEAR GLOVES, DO NOT CARRY THE TOOL BY HYDRAULIC HOSES,AND REPAIR LEAKS IMMEDIATELY..

5. DO NOT CARRY THE TOOL BY THE PIGTAIL HOSES.6. NEVER PUT YOUR FINGERS OR ANY OTHER OBJECT NEAR THE JAWS WHILE THE TOOL

IS CONNECTED TO A POWER SOURCE.7. NEVER USE YOU FINGERS TO DISLODGE A SPIKE, EVEN WITH THE TOOL DISCONNECTED

FROM THE POWER SOURCE. THERE STILL BE PRESSURE IN THE TOOL WHICH COULDCAUSE SUDDEN MOVEMENT OF THE JAWS.

8. NEVER PERFORM MAINTENANCE ON THE TOOL WHILE IT IS CONNECTED TO THE POWERSOURCE.

9. NEVER EXCEED MAXIMUM TOOL FLOW RATE OR 2000 PSI PRESSURE. DAMAGE TO TOOLOR PERSONAL INJURY OR DEATH MAY RESULT.

10. NEVER LEAN ON TOOL OR USE IT FOR PRYING.

7

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLERFLOW: 5 OR 10 GPM (19 OR 38 LPM)PRESSURE: 2000 PSI (140 BAR)BACK PRESSURE: MAX 250 PSI

OPERATION:1. WITH WITH THE POWER SOURCE IN THE �OFF� POSITION, CONNECT THE HOSES.

DO NOT DRAG THE SERVICE HOSE BY PULLING WITH THE TOOL. LOOP THE SER-VICE HOSE IN THE WORK AREA IN SUCH A WAY TO RELIEVE STRESS ON THEHOSE AND QUICK DISCONNECT FITTINGS WHILE WORKING. BE AWARE OF HOSELOCATION AT ALL TIMES.

2. CONNECT THE TOOL TO THE POWER SOURCE.3. TURN THE POWER SOURCE �ON� TO SUPPLY 5 OR 10 GPM TO TOOL

NOTE:WITH THE HANDLES POSITIONED �ACROSS THE RAIL� AS SHOWN IN THE PIC-TURE ON THE FRONT PAGE, THE SPIKE PULLER JAWS ARE ORIENTATED TO GRABTHE SPIKE ON THE ELONGATED SIDES OF SPIKE HEAD. IF OPERATION OF THE TOOL IS DESIRED FROM THE GAUGE OR FIELD SIDES OFTHE RAIL, THEN THE SPIKE PULLER TUBE ASSEMBLY MUST BE ROTATED 90°.FAILURE TO ROTATE THE TUBE ASSEMBLY CAN CAUSE THE JAWS TO NOT BEPROPERLY ALIGNED ON THE SPIKE WHICH WILL RESULT IN PREMATURE WEAROF THE JAWS.

4. SET THE SPIKE PULLER DOWN ON TOP OF THE SPIKE TO BE PULLED. TO ACTI-VATE, DEPRESS THE TRIGGER. CAUTION � WHEN SETTING THE SPIKE PULLERDOWN ON THE SPIKE DO NOT TRY TO SUPPORT THE PULLER RIGIDLY BY BRAC-ING AGAINST YOUR BODY. THE SPIKE PULLER WILL CENTER ITSELF ON THE SPIKEPRIOR TO PULLING OF THE SPIKE. THIS CENTERING ACTION WILL RESULT INSUDDEN MOVEMENTS OF THE SPIKE PULLER.

5. WHEN THE TOOL REACHES THE TOP OF THE STROKE, RELEASE THE TRIGGER.THE SPIKES WILL AUTOMATICALLY DROP OUT AT THE TOP OF THE STROKE.

8

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLERMAINTENANCE:1. CHECK TOOL FOR OVERALL WORKING CONDITION DAILY.2. INSPECT HOSES DAILY. AT FIRST SIGN OF ANY ABRASION OR CUT TO COVER, THE HOSES

MUST BE CHANGED.3. KEEP QUICK DISCONNECT COUPLERS CLEAN AND LUBRICATED.4. USE ONLY RECOMMENDED HYDRAULIC OILS. NEVER USE ATF OR MOTOR OILS.

SUGGESTED HYDRAULIC OILS:AMOCO RYKON MV CITGO A/W ALL TEMPSUN 2105 MOBIL D.T.E. 15CHEVRON EP-MV TEXACO �RANDO� HZIF YOUR LOCAL DISTRIBUTOR DOES NOT CARRY ANY OF THE ABOVE SUGGESTED HY-DRAULIC OILS USE THE FOLLOWING GUIDELINES:VISCOSITY @ 100° F �������������������.100-190SUSVISCOSITY INDEX���������������������MIN. 150EACH APPLICATION IS DIFFERENT, IF THERE ARE ANY QUESTIONS CONCERNING THERIGHT CHOICE FOR YOUR PARTICULAR APPLICATION CALL MATWELD FOR ASSISTANCE.

5. HAVE TOOL INSPECTED, AT LEAST ANNUALLY, BY A MATWELD OR MATWELD QUALIFIEDSERVICE REPRESENTATIVE TO DETERMINE IF TOOL IS IN NEED OF SAFETY CHANGESOR WORN PART REPLACEMENT.

6. CONTACT MATWELD ON A PERIODIC BASIS, AT LEAST ANNUALLY, FOR SERVICE BULLE-TINS, SAFETY NOTICES, OR OTHER IMPORTANT INFORMATION PERTAINING TO THISTOOL.

7. INSPECT DAILY TO INSURE THAT RAMPS HAVE A COATING OF GENERAL PURPOSE LU-BRICANT. SEE NEXT PAGE FOR GREASING PROCEDURE.

9

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLER

APPLYING LUBRICANT TO SPIKE PULLERS:OBSERVE THE FOLLOWING STEPS WHEN APPLYING GREASE OR LUBRICANT ON THE SPIKEPULLER RAMPS AND JAWS:1. DEPRESS OPERATING LEVER TO RETRACT JAWS INSIDE SPIKE PULLER HOUSING.2. TURN OFF HYDRAULIC POWER TO TOOL WITH OPERATING LEVER STILL DEPRESSED.

DISCONNECT TOOL FROM POWER SOURCE.3. APPLY GREASE VIA GREASE FITTING. ONE FULL MOVEMENT OF GREASE GUN WILL

PROVIDE SUFFICIENT GREASE TO JAWS AND RAMP BAR. KEEP HANDS CLEAR OF JAWAREA WHILE APPLYING GREASE.

4. RECONNECT TOOL TO POWER SOURCE AND TURN ON, JAWS WILL RETURN TO DOWNPOSITION. CYCLE SPIKE PULLER SEVERAL TIMES TO ASSURE AN EVEN COATING OFLUBRICANT.

REPAIR TROUBLESHOOTING:

1. SPIKE PULLER WON�T PULL SPIKES� SPIKE DRIVEN TOO CLOSE TO TIE PLATE.� WORN SPIKE PULLER JAWS � REPLACE� TUBE RAMPS NEED LUBRICATION � GREASE� TUBE DEFORMED AND JAWS WILL NOT GRAB SPIKE� PULLER HANGS IN FULLY RETRACED POSITION AND WILL NOT RELEASE UNTILPOWER IS SHUT OFF - INSPECT CHECK VALVE� CHECK RELIEF PRESSURE ON POWER SUPPLY � ADJUST TO 2000 PSI� TRIGGER VALVE NOT DEPRESSED ENOUGH, CAUSING LOSS OF PRESSURE � AD-JUST OR REPLACE (CHECK BY INSTALLING TEST GAUGE IN PRESSURE SIDE OFSPIKE PULLER AND DEPRESSING TRIGGER AND LETTING PISTON �DEAD HEAD�AT TOP OF STROKE, THE PRESSURE SHOULD EQUAL THE MAXIMUM PRESSUREREADING ON THE POWER UNIT � APPROXIMATELY 2000 PSI).

10

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLERGENERAL NOTES:

11

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

REVIEW OF HYDRAULIC PRINCIPLES

A. TOOL CIRCUIT

1. HYDRAULIC FORMULAS:

CID X RPM GPM X PSI GPM = 231 HP = 1714 (.85)

1456.9Example: HP required to deliver 10 GPM at 1500 PSI.

10 GPM X 1500 PSI = 15000 = 10.3 HP1456.9 1456.9

(subtract back pressure for tool HP)Estimated HP delivered by pump or used by tool.

PSI GPM 500 1,000 1,500 2,000 2,500 3,000 3 1.03 2.06 3.09 4.12 5.15 6.18 5 1.72 3.43 5.15 6.86 8.58 10.30 10 3.43 6.86 10.3 13.70 17.20 20.60 15 5.15 10.30 15.40 20.60 25.70 30.90

2. BACK PRESSUREBACK PRESSURE MEASURED AT THE TOOL RETURN PORT MUST NOT EXCEED THE MANU-FACTURERS BACK PRESSURE RATING. MOST MANUFACTURERS LIST THE MAXIMUM BACKPRESSURE FOR THEIR HYDRAULIC TOOLS AT 250 PSI. BACK PRESSURE MEASURED ONTHE RETURN SIDE OF THE TOOL IS THE FORCE REQUIRED TO GET THE OIL BACK TO THETANK. IN ALMOST ALL CASES THE LOWER THE BACK PRESSURE THE BETTER THE TOOLPERFORMANCE. FIRST, THE BACK PRESSURE IS SUBTRACTED FROM THE MAXIMUM TOOLPRESSURE TO ARRIVE AT A MAXIMUM TOOL OPERATING PRESSURE. FOR EXAMPLE, TOOLSWITH 2000 PSI OPERATING PRESSURE ARE INSTALLED ON A SYSTEM WITH 250 PSI BACKPRESSURE. THIS LEAVES 1750 PSI AS A MAXIMUM TOOL PRESSURE. IMAGINE A SYSTEMWITH 500 PSI BACK PRESSURE. 2000 MINUS 500 PSI BACK PRESSURE LEAVES ONLY 1500PSI FOR THE TOOL. SECOND, TOOLS ARE DESIGNED FOR PRESSURE TO BUILD ON THEPRESSURE SIDE OF THE TOOL. IF TOO MUCH PRESSURE BUILDS ON THE RETURN SIDE,NOT ONLY IS PERFORMANCE EFFECTED, BUT SEALS MAY BLOW. THIS IS WHY IT IS VERYIMPORTANT TO DIRECT THE FLOW INTO THE TOOL CORRECTLY. REVERSING THE HOSESTO TEST MAY RESULT IN BLOWN SEALS, DAMAGE TO THE TOOL, AND PERSONAL INJURY.

12

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200SPIKE PULLER

13

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLERPARTS LIST

ACCESSORIES01145 HAIR PIN KIT (AVAILABLE ON 01100 MODEL ONLY)

ITEM NO. PART NO. QTY. DESCRIPTION1 00145 QUICK DISCONNECT COUPLER 12 00146 QUICK DISCONNECT NIPPLE 13 00816 PIGTAIL HOSE 24 01101 TRIGGER 15 01102 VALVE ASSEMBLY 16 01103 HANDLE 17 01105 CYLINDER ASSEMBLY (FOR MODEL 01100) 18 01106 CHECK VALVE 19 01107 RETRACT HOSE 1

*10* 01108-TUBE TUBE 1*11* 01108-02 TUBE RAMP 212 01109 JAW BRACKET (FOR MODEL 01100) 113 01110 JAW PIN 214 01111 JAW 215 01113 SPRING 116 01114 SEAL & O-RING KIT 117 01141 SPRING RETAINER PIN 218 04205 HEAVY DUTY CYLINDER ASSEMBLY 1

(FOR MODEL 04200)19 205-08-06 1/2 T X 3/8 MP CONNECTOR 220 231P-02 #2 STRAIGHT THREAD SOCKET PLUG 221 405-08-06 1/2 T X 3/8 MP 90 DEGREE ELBOW 222 A1023 5/16-18 X 1 1/4 GR 5 CS 423 A1031 5/16-18 X 3 1/4 GR 5 CS 4

*24* A1033 5/16-24 X 1 GR 5 CS 2*25* A1035 5/16-24 X 1/2 GR 5CS 226 A2048 5/16-18 NYLON LOCK NUT 4

*27* A2190 1/4 SAE FLAT WASHER 2*28* A2191 5/16 SAE FLAT WASHER 14*29* A3809 1/4 LOCKWASHER 2*30* A3810 5/16 LOCKWASHER 231 A6108 5/16 X 1-1/4 SPRING PIN 1

*32* GF-105 1/4-28 X 3/8 STRAIGHT GREASE FITTING 233 04206 JAW BRACKET (FOR MODEL 04200) 1

*34* A0995 1/4-28 X 1/2 GR 5 CS 235 A6062 1/8 X 1 SPRING PIN 1

*Sold in 01108A Tube assembly.

14

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLER

WHEN ORDERING A #01145 HAIR PIN KIT YOU WILL RECEIVE THE FOLLOWING PARTS:ITEM NO PART NO. DESCRIPTION QTY 1 01146 SPRING 2 2 01150 HAIR PIN PULLER TUBE 1 3 01151 HAIR PIN PULLER JAW 2 4 01152 HAIR PIN PULLER PIVOT BLOCK 1 5 01153 HAIR PIN JAW PIN 2

15

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLERGENERAL NOTES:

16

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLERDECAL LEGEND:

17

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

LIMITED WARRANTYMATWELD, INC., PADUCAH, KY., WARRANTS TO THE ORIGINAL PURCHASER OF THIS PROD-UCT THAT THE PRODUCT WILL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIPFOR THE PERIOD OF ONE (1) YEAR AFTER THE DELIVERY OF SUCH PRODUCT TO THECUSTOMER. OTHER EQUIPMENT AND PARTS USED, BUT NOT MANUFACTURED BY MATWELDINC. ARE COVERED DIRECTLY BY THE WARRANTY OF THE MANUFACTURER OF THOSEPRODUCTS. PROOF OF PURCHASE MUST BE DOCUMENTED INCLUDING REFERENCE TO ASERIAL NUMBER LOCATED ON EACH TOOL. THE PURCHASER�S ONLY REMEDIES UNDERTHIS LIMITED WARRANTY SHALL BE LIMITED AT MATWELD�S SOLE OPTION TO THE FOL-LOWING: REPAIR, REPLACEMENT OR REFUND OF THE PURCHASE PRICE OF THE DEFEC-TIVE PRODUCTS. EACH OF THESE REMEDIES REQUIRES TIMELY NOTIFICATION OF THEDEFECT IN THE PRODUCT AND SUBSTANTIATION THAT THE PRODUCT HAS BEEN PROP-ERLY STORED, MAINTAINED AND USED. MATWELD�S OBLIGATIONS HEREUNDER EXTENDONLY TO THE PURCHASER OF THE PRODUCT AND NOT TO ANY THIRD PARTY.AS A CONDITION PRECEDENT TO MATWELD�S OBLIGATION HEREUNDER, THE DEFECTIVEPRODUCT MUST NOT HAVE BEEN ALTERED OR MODIFIED WITHOUT THE EXPRESS WRIT-TEN APPROVAL OF MATWELD, INC. THE PRODUCT MUST NOT HAVE BEEN SUBJECTED TODELIBERATE DAMAGE, SHIPPING DAMAGE, NEGLECT, TAMPERING BY UNAUTHORIZED PER-SONNEL OR DAMAGE BY IMPROPER USE, STORAGE OR MAINTENANCE. SERIAL NUMBERSMUST NOT HAVE BEEN ALTERED, DEFACED OR REMOVED. SUCH ACTION VOIDS LIMITEDWARRANTY.

EXCLUSIONS TO LIMITED WARRANTYTHIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRIT-TEN OR ORAL, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIEDWARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.LIMITED WARRANTY DOES NOT COVER NORMAL WEAR AND TEAR ITEMS SUCH AS FIL-TERS, HOSES, COUPLERS, BITS, SOCKETS, AUGERS, AND BATTERIES.

LIMITATION OF LIABILITYEXCEPT AS PROVIDED ABOVE, MATWELD SHALL IN NO EVENT BE LIABLE OR RESPON-SIBLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT, INCIDENTAL OR CONSEQUENTIAL,ARISING OUT OF THE USE OR MISUSE OR INABILITY TO USE THE PRODUCT, HOWEVERCAUSED AND ON ANY THEORY OF LIABILITY INCLUDING, WITHOUT LIMITATIONS, BREACHOF CONTRACT, TORT, (INCLUDING NEGLIGENCE OR STREET LIABILITY) AND NOT WITH-STANDING ANY FAILURE OF ANY REMEDY HEREIN OF ITS ESSENTIAL PURPOSE, EVEN IFMATWELD WAS AWARE OF THIS POSSIBILITY OF SUCH DAMAGE. MATWELD�S LIMITED WAR-RANTY AS SET FORTH ABOVE SHALL NOT BE ENLARGED, DIMINISHED OR AFFECTED BY,AND NO OBLIGATION OR LIABILITY SHALL ARISE OR GO OUT OF THE RENDERING OF TECH-NICAL ADVICE OR SERVICE BY MATWELD OR ITS AGENTS. THE FOREGOING MAY NOT BECHANGED EXCEPT BY WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICER OFMATWELD, THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE.

18

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLERGENERAL NOTES:

19

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

01100 & 04200 SPIKE PULLERGENERAL NOTES:

20

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

01/00

CUSTOMER INFORMATION:Name _____________________________________________________Company___________________________________________________Serial # of your Matweld tool___________________________________( Upon receiving your Matweld tool, make sure to list serial number above so that a good record is kept fororder information.)

MATWELD HYDRAULIC TOOL LISTAll Matweld Hydraulic Tools operate at

5 or 10 GPM @ 2000 PSIPOWER UNITS:70700 � HYDRA POWERED MODULAR SYSTEM02900 � DIESEL 1-10 GPM OR 2-5 GPM

(OPTIONAL CATALYTIC EXHAUST AND/OR MSHA CERTIFIED)00100 � GASOLINE 1-10 GPM OR 2-5 GPM02050 � GASOLINE 1-5 GPM

TRACK TOOLS:01600A � 1� IMPACT WRENCH04500D � ½� IMPACT DRILL00800A � 16� RAIL SAW03900A � REVERSING RAIL SAW01100 � SPIKE PULLER01300A � TIE TAMPER01400 � SPIKE DRIVER01500 � RAIL DRILL01000 � CHAIN SAWGRINDERS:04600 & 04650� STRAIGHT STONE CW & TRIGGER VERSION04700 & 04750 � STRAIGHT STONE CCW & TRIGGER VERSION04800 & 04850 � CUPSTONE & TRIGGER VERSION00700 � RAIL SURFACING GUIDE04300 & 04350 � 6� PROFILE & TRIGGER VERSION02400 � 10� OR 14� FROG AND SWITCH GRINDEROTHER PRODUCTS:HYDRAULIC MANIFOLDSHYDRAULIC TEST GAUGESHOSE REELSHYDRAULIC HOSESACCESSORIES