01 Owj200101 Wcdma Ue Behaviors in Idle Mode Issue1.1

8/3/2019 01 Owj200101 Wcdma Ue Behaviors in Idle Mode Issue1.1

1/65

www.huawei.com

Copyright 2008 Huawei Technologies Co., Ltd. All rights reserved.

WCDMA UE Behaviors

in Idle Mode


2/65

Page1Copyright 2008 Huawei Technologies Co., Ltd. All rights reserved.

Foreword UE behaviors in idle mode include :

PLMN selection

System information reception

Cell selection and reselection

Location registration

Paging procedure

Access procedure


3/65


Contents1. PLMN Selection

2. System Information Reception

3. Cell Selection and Reselection

4. Location Registration

5. Paging Procedure

6. Access Procedure


4/65






5. Paging Procedure

6. Access Procedure


5/65


Cell Search UE does not have UTRAN carrier information

In order to find a suitable cell to stay, UE will scan all thefrequencies in UTRAN. In each carrier, UE just need to find a

cell with best signal

UE has UTRAN carrier information

UE will try whether the original cell is suitable to stay. If not, UE

still need to scan all the frequencies about UTRAN in order to

find a suitable cell in PLMN


6/65


Cell Search

Slot synchronization

Frame synchronization and

code-group identification

Primary Scrambling codeidentification


7/65


PLMN Selection UE shall maintain a list of allowed PLMN types. In the

PLMN list, the UE arranges available PLMNs by priorities.When selecting a PLMN, it searches the PLMNs from the

high priority to the low.

The UE selects a PLMN from HPLMNs or VPLMNs.


8/65


PLMN Selection (Cont.) PLMN Selection in HPLMNs

Automatic PLMN Selection Mode

The UE selects an available and suitable PLMN from the whole

band according to the priority order

Manual PLMN Selection Mode

The order of manual selection is the same as that of automatic

selection.


9/65


PLMN Selection (Cont.) PLMN Selection in VPLMNs

If a UE is in a VPLMN, it scans the user controlled PLMNselector field or the operator controlled PLMN selector field

in the PLMN list to find the HPLMN or the PLMN with higher

priority according to the requirement of the automatic PLMN

selection mode.


10/65



2. System Information Reception3. Cell Selection and Reselection


5. Paging Procedure

6. Access Procedure


11/65


Structure of System Information System information is organized as a tree, including:

MIB (Master Information Block )

SB (Scheduling Block )

SIB (System Information Block )


12/65


System Information SIB1: Contains the system information for NAS and the

timer/counter for UE

SIB2: Contains the URA information

SIB3: Contains the parameters for cell selection and cell re-

selection

SIB5: Contains parameters for the common physical channels of

the cell

SIB7: Contains the uplink interference level and the refreshing

timer for SIB7 SIB11: Contains measurement controlling information


13/65


Reception of System Information The UE shall read system information broadcast on a BCH

transport channel when the UE is in idle mode or inconnected mode, that is, in CELL_FACH, CELL_PCH, or

URA_PCH state.


14/65



2. System Information Reception3. Cell Selection and Reselection


5. Paging Procedure

6. Access Procedure


15/65


Cell Selection When the PLMN is selected and the UE is in idle mode, the

UE starts to select a cell to camp on and to obtain services. There are four states involved in cell selection:

Camped normally

Any cell selection

Camped on any cell

Connected mode


16/65


Cell Selection (Cont.) Two types of cell selection:

Initial cell selection If no cell information is stored for the PLMN, the UE starts this

procedure.

Stored information cell selection If cell information is stored for the PLMN, the UE starts this

procedure.


17/65


Cell Selection Criteria

minqualqualmeasqual QQS=

oncompensatirxlevrxlevmeasrxlev PQQS = min

Criterion S is used by the UE to judge whether the cell is

suitable to camped on.

Criterion S : Srxlev > 0 & Squal > 0, where:


18/65


Parameters of S Criterion QUALMEAS

Parameter name: Cell Se-reselection quality measure

Recommended value: CPICH_ECNO

QQUALMIN

Parameter name: Min quality level

Recommended value: -18, namely -18dB


19/65


Parameters of S Criterion QRXLEVMIN

Parameter name: Min Rx level

Recommended value: -58, namely -115dBm

MAXALLOWEDULTXPOWER

Parameter name: Max allowed UE UL TX power

Recommended value: 21, namely 21dBm


20/65


Cell Reselection After selecting a cell and camping on it, the UE periodically

searches for a better cell according to the cell reselection

criteria. If finding such a cell, the UE selects this cell to

camp on.


21/65


Measurement Start Criteria (Cont.) Intra-frequency measurement

Squal Sintrasearch

Qqualmeas Qqualmin Sintrasearch

Qqualmeas Qqualmin + Sintrasearch


22/65


Measurement Start Criteria (Cont.) Inter-frequency measurement

Squal Sintersearch

Qqualmeas Qqualmin Sintersearch

Qqualmeas Qqualmin + Sintersearch


23/65


Measurement Start Criteria (Cont.) Inter-RAT measurement

Squal SsearchRATm

Qqualmeas Qqualmin SsearchRATm

Qqualmeas Qqualmin + SsearchRATm


24/65


Parameters of Measurement Start Criteria

IDLESINTRASEARCH

Parameter name: Intra-freq cell reselection threshold for idlemode

Recommended value: None

CONNSINTRASEARCH

Parameter name: Intra-freq cell reselection threshold for

connected mode



25/65



IDLESINTERSEARCH

Parameter name: Inter-freq cell reselection threshold for idlemode


CONNSINTERSEARCH

Parameter name: Inter-freq cell reselection threshold for

connected mode



26/65



SSEARCHRAT

Parameter name: Inter-RAT cell reselection threshold Recommended value: None


27/65


Measurement Start Criteria Description


28/65


Cell Reselection Criteria Criterion R is used for intra-frequency, inter-frequency cells

and inter-RAT cell reselection.

The cell-ranking criterion R is defined by :

nsoffsetnmeasnQQR

,,=

hystssmeass QQR += ,


29/65


Hysteresis and Time Interval

TimeTreselection

Quality

Rn

Rs

Qmeas,n

Qmeas,s

Qhyst,s

Qoffsets,n


30/65


Parameters of R Criteria IDLEQHYST1S

Parameter name: Hysteresis 1 for idle mode

Recommended value: 2, namely 4dB

CONNQHYST1S

Parameter name: Hysteresis 1 for connect mode

Recommended value: 2, namely 4dB


31/65


Parameters of R Criteria (Cont.) IDLEQHYST2S

Parameter name: Hysteresis 2 for idle mode

Recommended value: Qhyst1s for idle mode

CONNQHYST2S

Parameter name: Hysteresis 2 for connected mode

Recommended value: Qhyst1s for connected mode.


32/65


Parameters of R Criteria (Cont.) TRESELECTIONS

Parameter name: Reselection delay time

Recommended value: 1, namely 1s.


33/65


Parameters of R Criteria (Cont.) IDLEQOFFSET1SN

Parameter name: IdleQoffset1sn

Recommended value: 0, namely 0dB.

CONNQOFFSET1SN

Parameter name: ConnQoffset1sn



34/65


Parameters of R Criteria (Cont.) IDLEQOFFSET2SN

Parameter name: IdleQoffset2sn


CONNQOFFSET2SN

Parameter name: ConnQoffset2sn



35/65






5. Paging Procedure

6. Access Procedure


36/65


Location Registration The location registration includes:

Location update (for non-GPRS)

Route update (for GPRS)


37/65


Periodic Location Registration Periodic location registration is controlled by a Periodic

Location Update timer (T3212) or a Periodic Routing Area

Update timer (T3312)


38/65


Parameters of Location Registration T3212

Parameter name: Periodical location update timer [6min]

Recommended value: 10, namely 60min

ATT

Parameter name: Attach/detach indication

Recommended value: ALLOWED


39/65






5. Paging Procedure

6. Access Procedure


40/65


Paging Initiation CN initiated paging

Establish a signaling connection

UTRAN initiated paging

Trigger the cell update procedure

Trigger reading of updated system information


41/65


Paging Type 1 If UE is in CELL_PCH,URA_PCH or IDLE statethe paging

message will be transmitted on PCCH with paging type 1

CN RNC1 RNC2 NODEB1.1 NODEB2.1 UE

RANAPRANAP

RANAP RANAP

PCCH: PAGING TYPE 1

PAGING

PAGING

PCCH: PAGING TYPE 1


42/65


Paging Type 2 If UE is in CELL_DCH or CELL_FACH statethe paging

message will be transmitted on DCCH with paging type 2

CN SRNC UE

RANAPRANAP

PAGING

RRCRRC

DCCH: PAGING TYPE 2


43/65


Typical Call Flow of UEUE NAS UE AS NSS MSCpaging

AUTHENTICATION REQUEST

AUTHENTICATION RESPONSE

RR_SECURITY_CONTROL_REQ

(IK CK)

Secu rity mode control

SETUP

CALL CONFIRM

ALERT

CONNECT

CONNECT ACKNOWLEDGE

RAB setup process

paging

RR_EST_REQ (PAGING RESPONSE)

RR_PAING_IND

INITIAL_DIRECT_TRANSFER

(PAGING RESPONSE)

RANAPRANAP

RR C setup process


44/65


DRX Procedure UE receives the paging indicator on PICH periodically, that

is the Discontinuous Reception (DRX)

The value for the DRX paging cycle length is determined as

follows: :

DRX Cycle Length (2^K)PBP frames


45/65


DRX Procedure (Cont.) Through DRX, UE only listens to PICH at certain predefined

time. And UE will read the paging information on SCCPCH if

the paging indicator is 1.

The value of the Paging Occasion is determined as follows:

Paging Occasion (CELL SFN) =

{(IMSI mod M) mod (DRX cycle length div PBP)} * PBP

+ n * DRX cycle length + Frame Offset


46/65


DRX Procedure (Cont.)

( )( )( ) NpNp

SFNSFNSFNSFNPIq mod

144

144mod512/64/8/18

++++=

UE must calculate q to know which PI to monitor in one

frame of PICH

The qvalue is achieved by the following formula :

Where, PI = (IMSI div 8192) mod NP


47/65


DRX Procedure (Cont.)

PICH

Associated S-CCPCH frame

PICH frame containing paging indicator

Time offset between PICH and S-CCPCH


48/65


Parameters of DRX DRXCYCLELENCOEF

Parameter name: DRX cycle length coefficient

Recommended value: 6

PICHMODE

Parameter name: PICH mode

Recommended value: V36.


49/65


Parameters of DRX MACCPAGEREPEAT

Parameter name: Number of page re-TX



50/65






5. Paging Procedure

6. Access Procedure


51/65


Two Working Mode of UE Idle mode

After turning on, UE will stay in idle mode

Connected mode

UE will switch to connected mode which could be CELL_FACH

state or CELL_DCH state from the idle mode

After releasing RRC connection, UE will switch to the idle

mode from the connected mode


52/65


Random Access Procedure Definition

Random access procedure is initiated by UE in order to get

service from the system. Meanwhile, the access channels are

allocated to the UE by system


53/65


Random Access Channel

AICH accessslots

10 ms

#0 #1 #2 #3 #14#13#12#11#10#9#8#7#6#5#4p-a

#0 #1 #2 #3 #14#13#12#11#10#9#8#7#6#5#4

PRACHaccess slots

SFN mod 2 = 0 SFN mod 2 = 1

10 ms

Access slot set 1 Access slot set 2

Definition


54/65


RACH Sub-Channels

1413121110987

2107654361413121110985

543210764

8141312111093

765432102

1110981413121

765432100

11109876543210Random access sub-channels numberSFNmod 8

The access slots of different RACH sub-channels are illustrated by

the following table


55/65


Access Service Class The PRACH resources can be classified into several ASCs,

so as to provide RACH applications with different priorities.


56/65


Access Control Access Control is used by network operators to prevent

overload of radio access channels under critical conditions.

Access class 0~Access Class 9

Access class 11~Access Class 15

Access class 10


57/65


Mapping between AC and ASC The AC-ASC mapping information is optional and used for

the System Information Block 5 (SIB5) only.

Random Access Procedure


58/65

Random Access ProcedureSTART

Choose a RACH sub channel from

available ones

Get available signatures

Set Preamble Retrans Max

Set Preamble_Initial_Power

Send a preamble

Check the corresponding AI

Increase message part power by p-m based on preamble power

Set physical status to be RACH

message transmitted Set physical status to be Nackon AICH received

Choose a access slot again

Counter> 0 & Preamble power-maximum allowed power


59/65

Random Access ProcedureSTART

Choose a RACH sub channel fromavailable ones

Get available signatures

Set Preamble Retrans Max

Set Preamble_Initial_Power

Send a preamble

Check the corresponding AI

Increase message part power by p-m based on preamble power

Set physical status to be RACHmessage transmitted Set physical status to be Nack

on AICH received

Choose a access slot again

Counter> 0 & Preamble power-maximum allowed power


60/65


RRC Connection Message

Typical RRC connection messages

RRC_CONNECTION_REQUEST

RRC_CONNECTION_SETUP

RRC_CONNECTION_SETUP_COMPLETE

RRC_CONNECTION_RELEASE

UE Ti d C t t i Idl M d


61/65


UE Timers and Constants in Idle Mode

T300

Parameter name: Timer 300 [ms]

Recommended value: D2000, namely 2000ms

N300

Parameter name: Constant 300


UE Ti d C t t i Idl M d


62/65


UE Timers and Constants in Idle Mode

T312

Parameter name: Timer 312 [s]

Recommended value: 6, namely 6s

N312

Parameter name: Constant 312

Recommended value: D1, namely 1

RRC Connection Establish Channel


63/65


Type and Bit Rate RRCCAUSE

Parameter name: Cause of RRC connection establishment

Recommended value: none

SIGCHTYPE

Parameter name: Channel type for RRC establishment

Recommended value: none

RRC Connection Establish Channel


64/65


Type and Bit Rate INTRAMEASCTRL

Parameter name: IntraMeas Ctrl Ind for RRC establishment

Recommended value: SUPPORT


65/65

Thank youwww.huawei.com

01 Owj200101 Wcdma Ue Behaviors in Idle Mode Issue1.1

Documents

Transcript of 01 Owj200101 Wcdma Ue Behaviors in Idle Mode Issue1.1