Ó¡ Õ÷U«. ·MéIgÄLÚ®2 ¿ÎWÈ ìdT øåb i×ëËUzÞZ6Ì · 2019-10-15 · Title Ó¡...
3
OIML Certificate OIML Member State The Netherlands Number R60/2017-A-NL1-19.24 revision 1 Project number 2354831 Page 1 of 3 Issuing Authority NMi Certin B.V., OIML Issuing Authority NL1 1 October 2019 C. Oosterman Head Certification Board NMi Certin B.V. Thijsseweg 11 2629 JA Delft The Netherlands T +31 88 6362332 [email protected] www.nmi.nl This document is issued under the provision that no liability is accepted and that the applicant shall indemnify third-party liability. The notification of NMi Certin B.V. as Issuing Authority can be verified at www.oiml.org Issuing authority NMi Certin B.V. Person responsible: C. Oosterman Applicant and Manufacturer Coti Global Sensors, Inc. 5699 Highway 53 Harvest, AL35749 United States of America Identification of the certified type A bending beam or shear beam load cell, with strain gauges Type : CG-23, CG-23-LP, CG-23-SS, CG-23-SSW, CG-743, CG-745, CG-MK15, CG-SB3, CG-SB250, CG-SSB Characteristics See next page This OIML Certificate is issued under scheme A. This Certificate attests the conformity of the above identified Type (represented by the sample(s) identified in the OIML Test Report) with the requirements of the following Recommendation of the International Organization of Legal Metrology (OIML): OIML R 60 - Edition 2017 (E) for accuracy class C This Certificate relates only to the metrological and technical characteristics of the type of measuring instrument covered by the relevant OIML International Recommendation above-identified. This Certificate does not bestow any form of legal international approval. Important note: Apart from the mention of the Certificate’s reference number and the name of the OIML Member State in which the Certificate was issued, partial quotation of the Certificate and of the associated OIML Type Evaluation Reports is not permitted, although either may be reproduced in full.
Transcript of Ó¡ Õ÷U«. ·MéIgÄLÚ®2 ¿ÎWÈ ìdT øåb i×ëËUzÞZ6Ì · 2019-10-15 · Title Ó¡...
O I M L C e r t i f i c a t e
OIML Member State
The Netherlands
Number R60/2017-A-NL1-19.24 revision 1
Project number 2354831
Page 1 of 3
Issuing Authority
NMi Certin B.V., OIML Issuing Authority NL1
1 October 2019
C. Oosterman
Head Certification Board NMi Certin B.V.
Thijsseweg 11
2629 JA Delft
The Netherlands
T +31 88 6362332 [email protected]
www.nmi.nl
This document is issued under the
provision that no liability is
accepted and that the applicant
shall indemnify third-party liability.
The notification of NMi Certin B.V.
as Issuing Authority can be verified
at www.oiml.org
Issuing authority NMi Certin B.V. Person responsible: C. Oosterman
Applicant and
Manufacturer
Coti Global Sensors, Inc.
5699 Highway 53 Harvest, AL35749
United States of America
Identification of the
certified type
A bending beam or shear beam load cell, with strain gauges
Type : CG-23, CG-23-LP, CG-23-SS, CG-23-SSW, CG-743,
CG-745, CG-MK15, CG-SB3, CG-SB250, CG-SSB
Characteristics See next page
This OIML Certificate is issued under scheme A.
This Certificate attests the conformity of the above identified Type (represented by the sample(s) identified in the OIML Test Report) with the requirements of the following Recommendation of the
International Organization of Legal Metrology (OIML):
OIML R 60 - Edition 2017 (E) for accuracy class C
This Certificate relates only to the metrological and technical characteristics of the type of measuring instrument covered by the relevant OIML International Recommendation above-identified.
This Certificate does not bestow any form of legal international approval.
Important note: Apart from the mention of the Certificate’s reference number and the name of the
OIML Member State in which the Certificate was issued, partial quotation of the Certificate and of
the associated OIML Type Evaluation Reports is not permitted, although either may be reproduced in full.
O I M L C e r t i f i c a t e
OIML Member State
The Netherlands
Number R60/2017-A-NL1-19.24 revision 1
Project number 2354831
Page 2 of 3
The conformity was established by the results of tests and examinations provided in the associated
OIML Type Evaluation Reports: - No. NMi-2354831-01 dated 10 September 2019 that includes 51 pages;
- No. NMi-2354831-02 dated 10 September 2019 that includes 46 pages;
- No. NMi-2354831-03 dated 10 September 2019 that includes 48 pages.
Characteristics of the load cell:
Characterization of load cell capabilities Analog-passive load cell
Load cell construction Bending beam Shear beam
Maximum capacity (Emax) 45 kg up to
453 kg
453 kg up to
2265 kg
2265 kg up to
and including 11325 kg
Minimum dead load 0 kg
Accuracy Class C
Rated Output 2,0 mV/V ± 0,25% or 3,0 mV/V ± 0,25%
Maximum number of load cell intervals (n) (1) 3000 4000
Ratio of minimum LC Verification interval (1)
Y = Emax / vmin
20000 30000 50000
Ratio of minimum dead load output return (1)
Z = Emax / (2 * DR)
5000 7000 8000
Input impedance 385 ± 10
Temperature range -10 °C / + 40 °C
Fraction pLC 0,7
Humidity Class CH
Safe overload 150 % of Emax
Output impedance 350 ± 3
Recommended excitation 10 V AC / DC
Excitation maximum 15 V AC / DC
Transducer material Alloy steel or Stainless steel
Atmospheric protection Silicon rubber and/or welded
Remarks: 1. The characteristics for nmax, Y and Z can be reduced separately.
Each load cell produced is provided with an accompanying document with information about its
characteristics.
O I M L C e r t i f i c a t e
OIML Member State
The Netherlands
Number R60/2017-A-NL1-19.24 revision 1
Project number 2354831
Page 3 of 3
The above identified Type (represented by the sample(s) identified in the OIML Test Report) have been
found to comply with the additional national requirements established by the United States of America (NIST Handbook 44 and NCWM Publication 14), included in the Utilizer
Declaration:
- R 60 OIML-CS rev.2 Additional requirements from the United States Accuracy class III L; - R 60 OIML-CS rev.2 Additional requirements from the United States Marking requirements.
Revision History
This revision replaces the previous version.
Revision Date Change(s)
Initial 10-09-2019 -
1 01-10-2019 Correction of typos.
![¯ Ï4PBú j + 1f 1R : BñBñ...Ï4PBú "õ ] & j : ¯ +&µ ' #å T #y $4?" Bè cBé } T"õ Ó!¥# $å4?" BvB®BzB· * T"õ Ó!¥.\6Î Bè$ Bé j : ± BpB·B BtBvB®BzB· öÆ + 9Ô-+5Y9Õ?r-ë](https://static.fdocuments.net/doc/165x107/60afdc23cf2e427d392970d5/-4pb-j-1f-1r-bb-4pb-j-.jpg)
![4 30 « è6 ® +R´ - ê B Å Ç ñ® C 4 31 « ® ¾ · !\Ò\Ô\õ] ]d];]!]!].]d] ]O][ B66 C\Ø \ü ¨ ó\Ã\õ\½\Ò\¶ N \Õ \Ô\ô\è\Ã\ z 4 « (2 J ø · Â Ö É \\Õ\´\®\Ð\Ù\](https://static.fdocuments.net/doc/165x107/5c63a98409d3f26b1f8b8e7d/4-30-e6-r-e-b-a-c-n-c-4-31-ooo-dd.jpg)
![c]'] m F] ] ]d] · 2019-12-03 · © ®]c]'] m F] ] ]d] k µ © \Ø s Ð\Õ\Î\®\Ð ] ]R]d][\Ñ Ï è Ó\Ô m F\ü ¨ ó\Ã\õ\½\Ò\Ù\ É ` :\Ý < @\Õ\´\»\õ ý K :\Ý º Ó\Ô](https://static.fdocuments.net/doc/165x107/5f0c453d7e708231d4349204/c-m-f-d-2019-12-03-c-m-f-d-k-s-.jpg)
