Manufacturer / İmalatçi : Beka-Mak Makina Sanayi ve Tic. A,ş.

Address / Adres: İzmir Yolu 25.km Marmarabirlik yani 16370 Başköy-Bursa/Türkiye

Telefon : 02244490361 (4 hat )

Fax : 02244490360 Nilüfer / Bursa

Http : // www.bekamak.com.tr

E-mail : bekamak@bekamak.com

Warranty

- The firm guarantees the machine described hereby, designed in compliance with all regulations

in force, in particular safety and health regulations; the machine has undergone successful

testing.

- The warranty covers a period of 12 months. İt doesn’t cover electrical motors and tools.

- The purchaser is entitled ‘replacement of faulty parts’. Shipping and packing costs are at his

expense.

- The warranty doesn’t cover the parts damaged by falls or careless handling of the machine,

incorrect operation, non -compliance with the maintenance rules. Any tampering with the

machine, especially with the safety devices automatically expires the warranty and the

manufacturer will be freed from any responsibility.

- Any kind of alteration on the machine ends the warrant y and the manufacturer becomes free

from every kind of responsibility.

- No claim for damages shall be accepted in case the machine lays idle for a long period of time.

- Machine is designed to be run indoors. İt is not recommended to run the machine outdoors.

The serial number on the machine is a ‘main reference for the warranty’, instructions manual, after

sale service and identify the machine in case of need.

Important

Upon the delivery of the machine, the consumer must make himself sure that all

the devices indicated in the paragraph of the safety manual are present and working

correctly. Furthermore, he must mount in conformity with the instructions indicated those

devices which are not mounted at the time of delivery to facilitate transport.

When ordering spare parts

İt is necessary to state:

Ø Machine model

Ø Serial number and year of production

Ø İtem reference number

Without serial number no spare parts will be delivered

General İnformation

- The machines are manufactured in compliance with the accident prevention rules in

force.

- Strictly comply with the instructions contained in this manual to obtain the best

performance from the machine. Strict compliance with the rules contained herewith will

ensure optimum results and avoid any inconvenience caused by the non-compliance of

operation and maintenance instructions.

- Closely follow the instructions given below to avoid contacting the manufacturer for the

problems which can be easily solved..

- If after having strictly compliance with the given instructions, the purchaser still needs

the help of our technical assistance service, he must supply all the technical indications

necessary to determine the type of problem and/or the parts which are not functioning

correctly. This will enable our technic al assistance service to intervene quickly and

efficiently on the machine.

Copies of the instruction manual may be requested upon indication of the machine serial number.

General Safety Notes

All installation work including the electrical connection must only be carried out by qualified

personnel.

The machine must only be operated by a technically trained and experienced operative who is

also instructed in ‘safety at work ’ procedures.

Any adjustments, cleaning, repairs or changing of the saw blade must un der no circumstances be

performed unless the machine is fully isolated from the electrical power supply. Ensure the

emergency stop button on the control binnacle is pressed and the power supplies at the mains are

disconnected.”

The band saw must be regular ly inspected and maintained in good serviceable condition. Eye

protection, ear protection, gloves and protective clothing must be worn when any of the above

procedures are being carried out, as well as when cutting fluid is prepared, introduced or displaced

from the band saw machine (the relevant environmental regulations must be observed in case of

the use and disposal of cutting fluid etc.)

The band saw must be installed on ground. Observe the permissible floor load. Than the band

saw machine has been properly bolt to ground securely.

Allow sufficient working space around the band saw of at least 1 meter. İnstallations of stock roller

conveyors require additional space and possibly a lifting mechanism for heavy work pieces.

Always ensure that the working area around the band saw is well lit.

Safety İnstructions

ØBe sure that electrical connection is made carefully. To avoid unwanted situations like electrical shock, protect the main supply cable with a holster.

ØBefore running the machine, be sure that all of the protections are mounted properly and all the covers are closed.

ØAvoid from smoke and moisture.

ØPlease use the parts and equipments which are recommended. Usage of unsuitable parts and materials which arebigger than the capacity of the machine can cause unwanted situations.

ØCheck the machine and inform the defects everyday.

ØDon’t leave any material after chancing the band.

ØDo not hold the material while the machine is cutting. Always tighten the material by using essential parts.

ØPlease pay attention to choose the area of the machine which doesn’t include anything that creates difficulties to control the machine

ØPlease be sure that the teeth of the band are looking to correct direction.

· Don’t leave the band on the ground or any place that is dangerous for other people.

· Be careful when using the machine and keep the working area clean ( clean the saw dusts and oil traces )

· Pay attention to security instructions when using the machine.

· Don’t wear loose cloths when using the machine.

· Regardless use the protective gloves when using the machine.

· Don’t get close too much to the machine when running.

· Before carrying out any cleaning or maintenance procedure, disconnect the machine from main supply.

· İn some conditions, noise level can be about 85 db. Band choice and cutting speed is important factor for noise level.

· İllumination is an important factor for security.

· Ratio of coolant liquid is important for obtaining optimum lubrication.

· Never use the machine if you notice any fault of the machine or absence of any part of the machine.

- Control the emergency button at least once a week and be sure that it is working properly.

RELATED DİRECTİVES AND STANDARDS / İLGİLİ YÖNETMELİK VE STANDARTLAR

DİRECTİVES/DİREKTİFLER

MACHİNERY DİRECTİVE-/MAKİNE DİREKTİFİ 2006/42/EC

LOW VOLTAGE DİRECTİVE/DÜŞÜK VOLTAJ DİREKTİFİ 2006/95/EC

ELECTROMAGNETİC COMPATİBİLİTY DİRECTİVE/ELEKTRO MANYETİK UYUMLULUK DİREKTİFİ- 2004/108/EC

STANDARDS/STANDARTLAR

EN İSO 13857:2008; SAFETY OF MACHİNERY-SAFETY DİSTANCES TO PREVENT DANGER ZONES BEİNG REACHED BY UPPER LOWER LİMBS/ KOL VE BACAKLARİN

ULAŞABİLECEĞİ BÖLGELERDE TEHLİKENİN ÖNLENMESİ İÇİN GÜVENLİK MESAFELERİ

EN İSO 4413:20106: HYDRAULİC FLUİD POWER – GENERAL RULES AND SAFETY REQUİREMENTS FOR SYSTEMS AND THEİR COMPONENTS / HİDROLİK AKİŞKAN GÜÇ –

SİSTEMLER VE BİLEŞENLERİ İÇİN GÜVENLİK KURALLARİ VE GENEL KURALLAR.

EN İSO 13849 -1:2008/AC:2009; SAFETY OF MACHİNERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRİNCİPLES FOR DESİGN / MAKİNELERDE

GÜVENLİK- KUMANDA SİSTEMLERİNİN GÜVENLİKLE İLGİLİ KİSİMLARİ- BÖLÜM 1: TASARİM İÇİN GENEL PRENSİPLER

EN 13898:2003+A1:2009/AC:2010: MACHİNE TOOLS - SAFETY - SAWİNG MACHİNES FO R COLD METAL /TAKİM TEZGÂHLARİ – GÜVENLİK - METALLERİ SOĞUK İŞLEME İÇİN

TESTERE TEZGAHLARİ

EN İSO 12100:2010 ; SAFETY OF MACHİNERY - GENERAL PRİNCİPLES FOR DESİGN – RİSK ASSESMENT AND RİSK REDUCTİON/ MAKİNALARDA GÜVENLİK – TASARİM İÇİN

GENEL PRENSİPLER- RİSK DEĞERLENDİRİLMESİ VE RİSK AZALTİLMASİ.

EN 60204-1:2006/A1:2009; SAFETY OF MACHİNERY - ELECTRİCAL EQUİPMENT OF MACHİNES - PART 1: GENERAL REQUİREMENTS / MAKİNELERİN EMNİYETİ – MAKİNELERİN

ELEKTRİK DONANİMİ – BÖLÜM 1: GENEL GEREKLER

Warning

This chapter outlining the safety devices and norms was drawn up bearing in mind the normal use

of the machine as stated in the chapter on the operation of the machine and the adequate

preparation of the operators as regards the specific risks linked to the operation of the machine.

İf the machine isn’t used according to instruction given in the ‘purpose of the machine’ chapter in

this manual, the manufacturer isn’t responsible for any damage caused to people and things.

Furthermore, the manufacturer isn’t responsible for any damage to people and things and things

resulting from the non-compliance with the following warnings.

A) Adopt all the necessary precautions during loading, calibration, part replacement,

cleaning, and repair or maintenance operations to prevent someone else from turning

the machine on.

B) Do not temper with the safety devices and guards on the machine.

C) Do not remove any of the safety devices and guards on the machine.

Always make sure that safety devices and guards are remounted after their temporary removal for

technical reasons ordered by the boss

Connection To The Electrical System

Control panel is mounted on the electric panel. Machine is connected to the main

supply in the electrical panel. R, s and t shows the phases , n is neuter and pe is

grounding. Connection will be from the 13(l1) klemens which is at right klemens group.

Check the voltage which is mentioned at the first page of the manuel before setting the

electrical connection of the machine.

İf the cable phase line is correct phase control led lightens in that way it is prevented to

motors move on wrong ways. Be sure that the out-put voltage at the power supply is 22 ~ 28

vdc.

The machine is protected against short circuit with interrupters and against high voltage with

thermal relays. Grounding and neutralizing have to be done to protect the machine .

Technical data

DIMENSIONS BMSO 320GH BMSO 320GLH

Cutting Capacity

0°

mRound mm 320 320

xFlat mm 350 x 320 610 x 320rSquare mm 320 320

Cutting Capacity

-75°

mRound mm 320 320xFlat mm 350 x 200 580 x 320

rSquare mm 300 320

Cutting Capacity

-60°

mRound mm 300 320xFlat mm 300 x 200 510 x 320

rSquare mm 250 320

Cutting Capacity

-45°

mRound mm 260 320

xFlat mm 250 x 180 355 x 320rSquare mm 180 320

Cutting Capacity

-30°

mRound mm 160 260

xFlat mm 150 x 150 280 x 200rSquare mm 150 225

Main Drive Motor kW 2,2 2,2

Hydraulic Motor kW 1,1 1,1

Coolant Motor kW 0,12 0,12

Cutting Speeds m/min 20-100 20-100

Band Dimensions mm 3660 x 27 x 0,9 4160 x 34 x 1,1

Work Heigt mm 740 740

Weight Kg 1765 2000

DimensionsLength mm 2100 2370

Width mm 2220 2400

Height mm 1500 1500

Transportation And Carrying Of Machine

Important

Carry well-balanced with a strong rope which will be hooked to carrying rings

Fixing

Area that machine will be fixed should be flat and bowless. Machine base should be placed properly , linear and diagonal way . Get the machine to balance with 4pcs M10 screws that are on the legs, you should fix it with Ø10,5steel pins.

Operatıng Instructıon

Control panel

Explanınatıon Of The Electrıc Equıpment

Emergency stop ( so ): Stops the machıne completely.

Reset pushbutton :Reset emercancy stops and alarms.

Lamb (h) :Shows emercancy stops and alarms.

Potentıometer : Adjust the drıve motor speed.

Operatıon panel

F1 : Hydraulıc pump motor on-off

F2 : Drıve motor on-off

F3 : Fixed vice openıng.

F4 : Fixed vice clamping.

F5 : Movable vıce openıng.

F6 : Movable vıce clampıng.

F7 : Coolantpump motor on-off

F8 : Manual-automatıc select.

F9 : Slıde ahead. ( on manual posıtıon )

F10 : Slıde backward. ( on manual posıtıon )

F11 : Bow downstroke.

F12 : Bow upstroke.

reset the number of cuts (qt-o) – on automatıc posıtıon.

Manual cuttıng operatıon

1-swıtch on the maın swıtch. (waıt about 20 sec.)

2-press the reset button. (lamp wıll be off and maın menu appears on the panel)

3-adjust sq3 lımıt swıtch accordıng to the materıal’s dıameter or heıght.

4-press f1 key to the hydraulıc pump on.

5-select f12 key to the bow up. (sq3 lımıt swıtch maus be ın cırcuıt othervıse the machıne does not work..)

6-both cıces are open by usıng f3 and f5 keys.

7-select f9 key to go the movable vıce to the reference poınt.(ıt must be l=0 on the panel.)

8-select f4 key to clamp the materıal.

9-select f2 key to start the drıve motor.

10-adjust the cuttıng speed by usıng the potentıometer.

11-regulate the cuttıng pressure by the throttlıng valve.

12-select f7 key to coolantpump on. ( ıf needed.)

For the next cuttıng, follow the same way.

Automatıc cuttıng operatıon

1-at the same way on manual posıtıon, cut the fırst pıece.

2-select f8 key to select automatıc posıtıon.On panel:

3-ınput l1(requıred cuttıng length) and press enter key.

ınput q1(number of cuts) and than press enter key.

The fırst program has been done. (other ınputs must be “0”)

For the multıple program, follow the same way for the other programs;

L2;q2,l3;q3,...............l10;q10 (ıf needed).

(l1 and q1 ınputs must not be “0”. Otherwıse machıne wıll be locked.)

4-press f2 key to start the program.

5-adjust the cuttıng speed by usıng the potentıometer.

6-ragulate the cuttıng pressure by the throttıng valve.

7-select f7 key to coolantpump on. (ıf needed.)

To stop th cuttıng program, press f2 key to re-start the program, press f2 key agaın.

Alarms and warnıngs

When the counter reaches the preset number, the saw automatıcally stops. To return maın menu, press esc key.

When the materıal lenght ıs too short to be cut, the saw automatıcally stops. To return maın menu, press esc key.

When the blade has broken or ıs not tıghtened, the saw automatıcally stops or the drıve motor ıs prevented from workıng.

When a motor protectıon has trıpped, the saw automatıcally stops. Swıtch off the maın swıtch and check the motor protectıons.

Lımıt SwıtchesMaterıal-end lımıt swıtch ( sq1 ): when the materıal lenght ıs too shoert to be cut, ıt stops the machıne.

Upstroke lımıt swıtch ( sq3 ): after cuttıng, the bow ıs rısed by hydraulıc cylınder up to the adjusted level on the spındle. It can be adjusted by slıdıng the lımıt swıtch up or down.

Downstroke lımıt swıtch ( sq4 ): after cuttıng the materıal, ıt provıdes to rıe the bow up. P.s. Its place ıs adjusted by manufacturer, do nat change ıf unneccessary.

Slıde ahead lımıt swıtch ( sq2 ): thıs ıs the reference place of teh movable vıce.(l=0)

Blade breakıng lımıt swıtch ( sq5 ): when the blade has broken or ıs not tıghtened, ıt prevents the drıve motor workıng.

The adjustment of cuttıng pressure

Accordıng to the grade of materıal, ıt provıdes to regulate cuttıng pressure. The cuttıng pressure should be reduced when theblade ıs beıng dull. After that the blade must be.

Hydraulıc vıce: 40 bar

hydraulıc blade tensıon:40 bar(34 saw)

Hydromecanıc blade tensıon: mın.190 / max.210 bar(27 saw)

Hydromecanıc blade tensıon: mın.280 / max.300 bar(34 saw)

Maın pressure:40bar

The indicator of manometer must be in the green area (area ii). If the indicator is in one of the red area, this means that t he tension

of the blade is not in the acceptable level and it may cause unwanted results.

Area i : this shows that the tension of the blade is less than it must be. Adjust the blade tension.

Area ii : this shows that the tension of the blade is normal

Area iii : this shows that the tension of the blade is more than it must be. This may break the blade. Reduce the tension.

320gh-Glh Daıly Maıntenance

1-remove the chıps on wheel

2-clean the hydraulıc drawer

3-remove thechıps at shaft, flat and table

4-manometer should be between 190-210 bar

5-clean the tensıonıng slıde flats.

6-clean the chıps ın boron oıl tank.

Monthly Maıntenance

A-check the chıp brush

B.fıll grease oıl from the hole on the reductor shaft.

C check the tıghtness of wheel bolts.

D.control the oıl level ın hydraulıc tank

E. Fıll grease oıl from the hole on the tensıonıng slıde

Swıtch

1-blade break swıtch(on tensıonıng block)

2-upper swıtch

3-lower swıtch

4-measure reset swıtch

5-materıal fınısh swıtch

*cover swıtches are optıonal.

Workıng Prıncıples Of The Hydrolıc Dıagram Of The Machınes Bmso 320 H / Gh / Glh

Equıpments used

3. Tank

4. Hydrolıc engıne

5. Hydrolıc pump

6. Fıtler

7. Check valve

8. Open centered two-way dırectıon control valve (for the bow’s upwards movement)

9. Closed centered two-way dırectıon control valve (for the bow’s downwards movement)

10. Lockıng valve

11. (2 pcs) hydrolıc cylınder (for the bow)

12. (1 pcs) hydrolıc cylınder (for the vıce)

13. Safety valve

14. Hydrolıc oıl ıso 32

Blade Guıdance

For an accurate guıdance of the bandsaw blade there are two rıgıd and precıse vertıcal guıde arms fıtted wıth rollers for twıstıng pretwıstıng and carbıde ınserted plates for the fınal and exact blade gııde. Put the blade guıde arms always as close as possıble to the materıal to be cut and tıghten them.

The play of the blade can be re-set by alterıng the posıtıon of a carbıte ınserted guıde plate.

The mınumum play should be 0,04 mm.

Trouble Shootıng

ü The bow comes down out of control;

ü The seals ınsıde of the hydrolıc pıstons mıght be worned out; replace.

ü Check valve mıght be bunged up wıth dırth; clean.

ü Center of the dırectıon valve mıght be bunged up wıth dırth; clean.

ü The o-rıngs of pressure adjustıng valvemıght be worned out; replace.

ü Sounds comıng from the front pulley

ü The bearıngs mıght be worned out; replace.

ü The blade ıs leanıng to one sıde whıle cuttıng

ü Carbıdes must be worned out; replace,

ü Blade guıdıng bearıngs mıght be worned out; replace

ü the warnıng lamp on the control panel ıs on,

ü Check the blade thıghenıng swıtch

ü Check the drıve swıtch

Check the upper lımıt swıtch

REGULATIONS

DEFECT SYMPTOMS CAUSE OF DEFECT TYP OF REPAIR

AFTER SWITCHING ON THE MAIN A) FUSE IS OFF. A) RESET FUSE.SWITCH, THE LAMP ON CONTROLPANEL DOES NOT WORK. B) BUMT BULB. B) REPLACE BULB.

AFTER GOING THE BOW DOWN A) THE BOW DOES NOT TOUCH A) RE-ADJUST S3 LIMIT SWITCH.COMPLATELY, DOES NOT GO UP. S3 LIMIT SWITCH.

B)REVERSE DIRECTION PUMP B)TAKE THE COVER OFF AT THEROTATION. BACSIDE OF THE MACHINE

AND CHECK IF DIRECTION OFROTATION AGREE WITH THEARROW. IN CASE OF DISCRE-PACY, PHASES IN THEPUMP SUPPLY.

AFTER PRESING START BUTTON A)S2 LIMIT SWITCH DOES NOT A) PRESS BOW-UP BUTTON.THE MOTOR DOES NOT WORK. GET IN TOUCH WITH THE BOW.

B) COUNTER IS LOCKED. B) PRESET THE COUNTER ANDPRESS RESET BUTTON.

C) THERMAL PROTECTION HAS C) WAIT A FEW MINUTES UNTIL WORKED

. THERMAL RELAY COOL. IF THE MOTOR STILL DOES NOT WORK.PRESS RESET BUTTON.

PUMP DOES NOT SUPPLY A) REVERSE DIRECTION OF A) EXCHANGE PHASES IN THECOOLANT. PUMP ROTATION. PUMP’S SUPPLY.

B) LACK OF COOLANT. B) POUR IN COOLANT.

C) SHUT VALVES THAT CUM OFF C) OPEN VALVE’S.COOLANT. D) THERNAL PROTECTION HAS D) WAIT A FEW MINUTES UNTILWORKED. RELAY COOL. IF THE MOTOR

STILL DOES NOT WORK PRESSKEY.

IF THE ABOVE DEFECTS HAVE BEEN REMOVED AND IF THE MACHINE STILL DOES NOT WORK, CHECK APPROPRIATE ELECTRIC CIRCUITS AND THEN CALL A CREW TRAINED TO REPAIR FOR THIS PURPOSE.

Changing The Hydraulic OilPouring Out The Hydraulic Oil

ü Lower down until it receives the cutting head.ü Remove hydraulic hose union at head lifting ü Put the removed hydraulic end of the hose into a

container.ü Empty the oil by pressing head lifting button at control

panel.

After empting the oil, fix the hydraulic hose union to the same place.

Refilling the hydraulic oil

The hydraulic oil filling

ü Remote the bolts of hydraulic drawer, then pull it out.ü Open the store cover.ü Pour 32 numbered iso hydraulic oil into tank. (8lt

capacity.)ü Close the tank cover and move the drawer into the

body

Fasten the screws to the body again with the help of hydraulicdrawer.

Filling Of Coolant

Consisting of a mixture of liquid and water coolant liquid should be used for steel cutting. Coolant should not be used for cutting casting. Specific periods of time (at least once a month) , coolant should be drained and clean chips. İf amount of coolant is not enough, add to the tank. (4 liters of tank capacity. Collant mixing ratio 1/10)

Setting New Blade

· First of all both guard flaps and the guards which are on the guide arms have to be open upwards.

· Loosen the blade by the hand level so far that the blade can be easily taken off around the pulleys

· The same way but vic averse, fit and tighten the new blade. There is also possibility to tighten the blade by torque meter.

· Always pay attention to the teeth of the blade’s direction is correct. İf not correct it.

Cutting Speeds

The machine has two pre-selected cutting speeds of 20 and 100 m/sec. Cutting speeds has to be selected according to the grade

and dimensions of the material. İf any vibration and/or noise raises from the blade, change the speed.

· All the details about the cutting of various materials and dimensions are given below

CUTTING RECOMENDATIONS

NOTE:THE CUTTING SPEEDS GIVEN BELOW ARE GUIDELINES ONLY

MATERIALMATERIAL DESIGNATION

DIN

MATERIAL

NO

CUTTING SPEED COOLANT

SPECIAL

LG-SUPER

BI-METAL

EMULSIONCUTTING OIL

YES NOSTRUCTUAL STEEL ST 35 – ST 42 1.0308-

007740 - 55 60 - 80 1:10 X

ST 350 – ST 70 1.0052-0070

30 - 45 50 - 70 1:20 X

HARDENING STEELC 10 - C 16 1.0301-

040145 - 65 60 - 90 1:10 X

14 NICR 14 1.5752 30 - 40 40 – 50 1:10 X21 NICR MO 2 1.6523 30 - 45 45 - 55 1:10 X

16 MRCR 5 1,7131 30 - 45 50 - 65 1:10 XNITRICTED STEEL

(HEAT TREATED)

34 CRAL 6 1,8504 ------ 20 - 35 1:20 X34 CR AL NI 7 1,8550 ------ 20 - 35 1:20 X

FREE CUTTING STEEL 9 S 20 1,0711 45 - 65 70 - 120 1:10 X

HEAT TREATABLE STEEL

C 35 C 45 1,0501-0503

35 - 55 55 - 75 1:20 X41 CR 4 1,7035 35 - 35 40 - 60 1:20 X40 MN 4 1,5038 35 - 45 50 - 65 1:20 X

42 CRMO 4 1,7225 30 - 40 35 - 50 1:20 X36 NI CR 6 1,5710 30 - 40 50 - 60 1:20 X

24 NI CR 14 1,5754 25 - 35 40 - 60 1:20 XBALL BEARING STEEL 100 - CR 6 1,3505 25 - 35 50 - 65 1:30 X

105 – CR 4 1,3503 25 - 35 50 - 65 1:30 X100 – CRMO 6 1,3520 20 - 30 40 - 50 1:30 X

SPRING STEEL 65 SI 7 1,0906 30 - 40 40 - 60 1:30 X50 CRV 4 1,8159 30 - 40 40 - 60 1:30 X

UNALLOYED TOOL STEEL C 80 W 1 1,1525 25 - 35 50 - 60 1:30 XC 125 W 1 1,1560 20 - 30 20 - 35 1:30 XC 105 W 2 1,1645 25 - 35 40 - 50 1:30 X

ALLOYED TOOL STEEL

105 CR 5 1,2060 30 - 40 50 - 60 1:30 XX 210 CR 12 1. 2080 ------ 20 - 35 ------ X

X 40 CR MO V 51 1,2344 20 - 30 30 - 40 1:30 XX 210 CR W 12 1,2436 ------ 20 - 30 ------ X

X 165 CR MP V 12 1,2601 ------ 20 - 35 1:30 X56 NICRMOV 7 1,2714 25 - 30 20 - 40 1:30 X

100 CRMO 5 1,2303 20 - 30 35 - 45 1:30 XX 32 CRMOV 33 1,2365 20 - 30 30 - 45 1:20 X

HIGH SPEED STEELS 5-6-2 1,3343 ------ 25 - 40 1:30 X

S 5-6-2-5 1,3243 ------ 25 - 40 1:30 XS 18-0-1 1,3355 ------ 25 - 40 1:30 X

S 18-1-2-10 1,3265 ------ 25 - 40 1:30 XVALVE STEEL X 45 CRSI 93 1,4718 ------ 30 - 40 1:20 X

X 45 CRNIW 189 1,4873 ------ 30 - 40 1:20 XHIGH TEMPERATURE

STEELCRNI 2520 1,4843 ------ 25 - 40 1:10 X

X 20 CRMOV 211 1,4922 ------ 25 - 40 1:10 XX5 NICRTI 2615 1,4980 ------ 25 - 40 1:10 X

HEAT RESISTING STEEL X 10 CRAL 7 1,4713 ------ 20 - 35 1:10 XX 15 CRNISI 25 / 20 1,4841 ------ 20 - 35 1:10 X

X 10 CRSI 6 1,4712 ------ 20 - 35 1:10 XSTAINLESS AND ACID

RESISTING STEEL

X 5 CRNI 189 1,4301 ------ 25 - 35 1:10 XX 10 CRNIMPT 1810 1,4571 ------ 25 - 35 1:10 X

X 10 CR 13 1,4006 ------ 25 - 35 1:10 XX 5 CRNIMO 1810 1,4401 ------ 25 - 35 1:10 X

STEEL CASTING GS – 38 30 - 40 50 - 60 1:50 XGS – 60 30 - 40 50 - 60 1:50 X

CAST IRONGG – 16 30 - 40 40 - 50 ------ XGG – 30 30 - 40 40 - 50 ------ X

GTW – 40 30 - 40 40 - 50 ------ XGTS – 65 30 - 40 40 - 50 ------ X

HIGH TEMPERATURE NICKEL ALLOYS

NIMONIC 2,4631 ------ 15 - 25 1:10 XHASTELLOY X 2.4972 ------ 15 - 25 1:10 X

INCONEL 2,4640 ------ 15 - 25 1:10 XALUMINIUM ALLOYS AL 99,5 3,0255 80 - 300 100 - 700 1:10 X

ALMG 3 3,3535 80 - 300 100 - 700 1:10 XBRONZE / TIN BRONZE CUSN 6 2,1020 50 - 70 70 - 100 1:50 X

G – CUSN 10 2,1050 50 - 70 70 - 100 1:50 XALUMINIUM - BRONZE CUAL 8 2,0920 30 - 45 50 - 70 1:30 X

CUAL 8 FE 38 2,0920,60 30 - 40 40 - 50 1:20 XRED BRASS G – CUSN 10 ZN 2,1086,01 30 - 45 70 - 100 1:50 X

G – CUSN 5 ZN PB 2,1096,01 30 - 45 70 - 100 1:50 XBRASS CUZN 10 2,0230 80 - 200 100 - 300 1:50 X

CUZN 31 S 2,0490 80 - 200 100 - 300 1:50 X

1

TURN TABLE AND SPRING GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.01.01 M12*40 INBUS002 BMSO 320GH/GLH.01.02 BASE003 BMSO 320GH/GLH.01.03 MATERIAL LOWER FLAT004 BMSO 320GH/GLH.01.04 M10*30 SETSKUR005 BMSO 320GH/GLH.01.05 MATERIAL FEEDING PART006 BMSO 320GH/GLH.01.06 SPRING007 BMSO 320GH/GLH.01.07 LAMASI008 BMSO 320GH/GLH.01.08 BOW CONNEC. CASTING PART LEFT009 BMSO 320GH/GLH.01.09 BOW CONNECTION CASTING SHAFT010 BMSO 320GH/GLH.01.10 REKOR011 BMSO 320GH/GLH.01.11 M6*25 INBUS012 BMSO 320GH/GLH.01.12 REKOR013 BMSO 320GH/GLH.01.13 BOW CONNECTION CASTING014 BMSO 320GH/GLH.01.14 M10*30 INBUS015 BMSO 320GH/GLH.01.15 PIN Q8016 BMSO 320GH/GLH.01.16 BOW CONNECT. CASTING RIGHT017 BMSO 320GH/GLH.01.17 MATERIAL LEAN FLAT018 BMSO 320GH/GLH.01.18 M8*25 INBUS019 BMSO 320GH/GLH.01.19 BEARING BK 4020 A020 BMSO 320GH/GLH.01.20 SHAFT021 BMSO 320GH/GLH.01.21 BEARING 7208 B022 BMSO 320GH/GLH.01.22 KM NUT023 BMSO 320GH/GLH.01.23 SPRING GROUP PART 1024 BMSO 320GH/GLH.01.24 M16 NUT025 BMSO 320GH/GLH.01.25 SPRING GROUP PART 2026 BMSO 320GH/GLH.01.26 SPRING GROUP PART 3027 BMSO 320GH/GLH.01.27 SPRING GROUP PART 4028 BMSO 320GH/GLH.01.28 M8*20 SETSKUR029 BMSO 320GH/GLH.01.29 SPRING GROUP 5030 BMSO 320GH/GLH.01.30 SPRING GROUP 6

2

TENSIONING GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.02.01 KNOP BLOCKS002 BMSO 320GH/GLH.02.02 TENSIONING KNOP003 BMSO 320GH/GLH.02.03 TENSIONING SHAFT004 BMSO 320GH/GLH.02.04 BEARING T 77005 BMSO 320GH/GLH.02.05 METAL RING006 BMSO 320GH/GLH.02.06 WASHER 6 PC007 BMSO 320GH/GLH.02.07 42*86*3,53 ORİNG008 BMSO 320GH/GLH.02.08 LEAN BLOCK ( INNER)009 BMSO 320GH/GLH.02.09 34*59*2,62 ORİNG010 BMSO 320GH/GLH.02.10 LEAN BLOCK ( OUTER)011 BMSO 320GH/GLH.02.11 1/8 REKOR012 BMSO 320GH/GLH.02.12 M8*80 İNBUS013 BMSO 320GH/GLH.02.13 LEAN BLOCK014 BMSO 320GH/GLH.02.14 BRASS015 BMSO 320GH/GLH.02.15 M8*30 İNBUS016 BMSO 320GH/GLH.02.16 TENSIONING NUT017 BMSO 320GH/GLH.02.17 M8*20 SETSKUR018 BMSO 320GH/GLH.02.18 TENSIONING SLEDGE019 BMSO 320GH/GLH.02.19 M8*30 İNBUS020 BMSO 320GH/GLH.02.20 SLEDGE FLAT021 BMSO 320GH/GLH.02.21 M8*35 INBUS022 BMSO 320GH/GLH.02.22 FRONT WHEEL SHAFT023 BMSO 320GH/GLH.02.23 CR 30316 BEARING024 BMSO 320GH/GLH.02.24 472/72 SEGMAN025 BMSO 320GH/GLH.02.25 METAL RING026 BMSO 320GH/GLH.02.26 FRONT WHEEL027 BMSO 320GH/GLH.02.27 DRIVE WHEEL COVER028 BMSO 320GH/GLH.02.28 MB6 SECURITY WASHER029 BMSO 320GH/GLH.02.29 KM6 NUT030 BMSO 320GH/GLH.02.30 MANOMETRE

3

VICE GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.03.01 ANGLE SHEET002 BMSO 320GH/GLH.03.02 LOWER FLAT003 BMSO 320GH/GLH.03.03 UPRIGHT FLAT ( FRONT)004 BMSO 320GH/GLH.03.04 M10*35005 BMSO 320GH/GLH.03.05 FIXED VICE CONNECTION PART006 BMSO 320GH/GLH.03.06 FIXED VICE007 BMSO 320GH/GLH.03.07 M10*35 INBUS008 BMSO 320GH/GLH.03.08 HYDRAULIC DISTRIBUTOR009 BMSO 320GH/GLH.03.09 M6*25 INBUS010 BMSO 320GH/GLH.03.10 M16*60 INBUS011 BMSO 320GH/GLH.03.11 PISTON CONNECTION PART012 BMSO 320GH/GLH.03.12 TOP CLAMPING FLAT ( LEFT)013 BMSO 320GH/GLH.03.13 M8*25 INBUS014 BMSO 320GH/GLH.03.14 M10*110 INBUS015 BMSO 320GH/GLH.03.15 VICE LOWER FLAT016 BMSO 320GH/GLH.03.16 UPRIGHT FLAT ( REAR)017 BMSO 320GH/GLH.03.17 MOVABLE VICE018 BMSO 320GH/GLH.03.18 MOVABLE VICE NUT019 BMSO 320GH/GLH.03.19 M12*70 INBUS020 BMSO 320GH/GLH.03.20 M12*35 INBUS021 BMSO 320GH/GLH.03.21 TOP CLAMPING FLAT ( RIGHT)022 BMSO 320GH/GLH.03.22 PISTON CONNECTION PART023 BMSO 320GH/GLH.03.23 M10*25 INBUS024 BMSO 320GH/GLH.03.24 PISTON FRONT COVER025 BMSO 320GH/GLH.03.25 M6*25 INBUS026 BMSO 320GH/GLH.03.26 DUST SEAL 30*38027 BMSO 320GH/GLH.03.27 ORING 42,86*3,53028 BMSO 320GH/GLH.03.28 OIL SEAL 30*40*8029 BMSO 320GH/GLH.03.29 PISTON SHAFT PIPE030 BMSO 320GH/GLH.03.30 SHAFT 6*720031 BMSO 320GH/GLH.03.31 PISTON SHAFT032 BMSO 320GH/GLH.03.32 SEAL SET K18 050-034 (50*34*20,5)033 BMSO 320GH/GLH.03.33 PISTON REAR COVER034 BMSO 320GH/GLH.03.34 M6 NUT035 BMSO 320GH/GLH.03.35 REKOR036 BMSO 320GH/GLH.03.36 REKOR

4

PISTON GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.04.01 24*1,5 NUT002 BMSO 320GH/GLH.04.02 CONNECTION PIN003 BMSO 320GH/GLH.04.03 Ø23*Ø20* 25 METAL RING004 BMSO 320GH/GLH.04.04 LOWER BLOCK005 BMSO 320GH/GLH.04.05 1/8 Ø6 REKOR006 BMSO 320GH/GLH.04.06 42,86*3,53 ORING007 BMSO 320GH/GLH.04.07 472/50 SEGMAN008 BMSO 320GH/GLH.04.08 CYLINDER PIPE009 BMSO 320GH/GLH.04.09 1/8 Ø6 ELBOW010 BMSO 320GH/GLH.04.10 50*34*20,5 SEAL SET011 BMSO 320GH/GLH.04.11 PISTON SHAFT012 BMSO 320GH/GLH.04.12 BAND013 BMSO 320GH/GLH.04.13 UPPER BLOCK014 BMSO 320GH/GLH.04.14 DUST SEAL 30*38015 BMSO 320GH/GLH.04.15 UPPER CONNECTION BLOCK016 BMSO 320GH/GLH.04.16 M6*8 SETSKUR017 BMSO 320GH/GLH.04.17 Ø20*Ø18*16 METAL RING018 BMSO 320GH/GLH.04.18 471/16 SEGMAN019 BMSO 320GH/GLH.04.19 Ø16 PIN

5

REDUCTOR GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.05.01 M8*60 INBUS002 BMSO 320GH/GLH.05.02 REAR WHEEL003 BMSO 320GH/GLH.05.03 REDUCTOR SHAFT004 BMSO 320GH/GLH.05.04 8*7*35 WEDGE005 BMSO 320GH/GLH.05.05 65*90*13 SEAL006 BMSO 320GH/GLH.05.06 472/99 SEGMAN007 BMSO 320GH/GLH.05.07 NJ210 BEARING008 BMSO 320GH/GLH.05.08 METAL RING009 BMSO 320GH/GLH.05.09 METAL RING010 BMSO 320GH/GLH.05.10 6210 BEARING011 BMSO 320GH/GLH.05.11 M35x1,5 SOMUN012 BMSO 320GH/GLH.05.12 WASHER013 BMSO 320GH/GLH.05.13 M10*110 INBUS014 BMSO 320GH/GLH.05.14 REDUCTOR BEARING015 BMSO 320GH/GLH.05.15 M8*25 016 BMSO 320GH/GLH.05.16 FLANGE

6

CARBIDE GUIDE GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.06.01 MOVING ARM002 BMSO 320GH/GLH.06.02 10*50 HANDLE003 BMSO 320GH/GLH.06.03 CARBIDE BLOCK004 BMSO 320GH/GLH.06.04 M8*30 INBUS005 BMSO 320GH/GLH.06.05 CARBIDE006 BMSO 320GH/GLH.06.06 M4*8 INBUS007 BMSO 320GH/GLH.06.07 6000 BEARING008 BMSO 320GH/GLH.06.08 10*50 SHAFT009 BMSO 320GH/GLH.06.09 M8*25 INBUS010 BMSO 320GH/GLH.06.10 BLADE DIRECTION BLOCK011 BMSO 320GH/GLH.06.11 ECCENTRIC PIN012 BMSO 320GH/GLH.06.12 STRAIGHT PIN013 BMSO 320GH/GLH.06.13 6000 BEARING014 BMSO 320GH/GLH.06.14 Ø10 RİNG015 BMSO 320GH/GLH.06.15 M8*15 INBUS016 BMSO 320GH/GLH.06.16 BLADE GUIDE

7

SWITCH AND BRUSH GROUP

PART NMR PART CODE PART NAME001 BMSO 320GH/GLH.07.01 CONNECTION FLAT

002 BMSO 320GH/GLH.07.02 LEFT BLOCK003 BMSO 320GH/GLH.07.03 M10*30 INBUS

004 BMSO 320GH/GLH.07.04 SLEDGE FLAT

005 BMSO 320GH/GLH.07.05 M8*20 INBUS006 BMSO 320GH/GLH.07.06 M10*30 INBUS

007 BMSO 320GH/GLH.07.07 M6*30 INBUS008 BMSO 320GH/GLH.07.08 STRAIGHT SHAFT

009 BMSO 320GH/GLH.07.09 BEARING 6000

010 BMSO 320GH/GLH.07.10 SWITCH LOWER FLAT011 BMSO 320GH/GLH.07.11 M4*30 INBUS

012 BMSO 320GH/GLH.07.12 SWITCH UPPER FLAT013 BMSO 320GH/GLH.07.13 FLAT

014 BMSO 320GH/GLH.07.14 SWITCH FIXED FLAT015 BMSO 320GH/GLH.07.15 M6*15 INBUS

016 BMSO 320GH/GLH.07.16 M6*30 BOLT

017 BMSO 320GH/GLH.07.17 M8*20 INBUS018 BMSO 320GH/GLH.07.18 BRUSH CONNECTION BLOCK

019 BMSO 320GH/GLH.07.19 BRUSH CONNECTION SHAFT020 BMSO 320GH/GLH.07.20 BRUSH CONNECTION ARM

021 BMSO 320GH/GLH.07.21 SEGMAN 471/10

022 BMSO 320GH/GLH.07.22 BRUSH

8

FRAME GROUP

PART NMR PART CODE PART NAME001 BMSO 320GH/GLH.08.01 FLAT

002 BMSO 320GH/GLH.08.02 PISTON SHAFT FLAT 150*80*20003 BMSO 320GH/GLH.08.03 M10*35 INBUS

004 BMSO 320GH/GLH.08.04 M16 NUT

005 BMSO 320GH/GLH.08.05 M10*20 INBUS006 BMSO 320GH/GLH.08.06 CONNECTION PART( RIGHT)

007 BMSO 320GH/GLH.08.07 M10*35 INBUS008 BMSO 320GH/GLH.08.08 SQUARE FLAT A) FRONT B) BACK

009 BMSO 320GH/GLH.08.09 TOP CLAMPING HYDRAULIC DEALER

010 BMSO 320GH/GLH.08.10 M5*30 INBUS011 BMSO 320GH/GLH.08.11 REKOR 1/4 8

012 BMSO 320GH/GLH.08.12 UPPER CONNECTION FLAT013 BMSO 320GH/GLH.08.13 M10*20 INBUS

014 BMSO 320GH/GLH.08.14 PIN 8*30015 BMSO 320GH/GLH.08.15 TOP CLAMPING PISTON CONNECTION FLAT

016 BMSO 320GH/GLH.08.16 M10*45 INBUS

017 BMSO 320GH/GLH.08.17 FEEDER FIXED VICE JAW018 BMSO 320GH/GLH.08.18 M10*25 INBUS

019 BMSO 320GH/GLH.08.19 FEEDER FIXED VICE JAW FLATS020 BMSO 320GH/GLH.08.20 M8*10 INBUS H.B.

021 BMSO 320GH/GLH.08.21 CONNECTION BLOCK LEFT

022 BMSO 320GH/GLH.08.22 FRAME CONNECTION BLOCK (FRONT)023 BMSO 320GH/GLH.08.23 SHAFT CONNECTION (FRONT)

024 BMSO 320GH/GLH.08.24 M10*70 INBUS025 BMSO 320GH/GLH.08.25 PIN 8*60

026 BMSO 320GH/GLH.08.26 M10*15 INBUS027 BMSO 320GH/GLH.08.27 PIN 8*20

028 BMSO 320GH/GLH.08.28 M10*50 INBUS

029 BMSO 320GH/GLH.08.29 CONNECTION BLOCK( BACK)030 BMSO 320GH/GLH.08.30 SHAFT CONNECTION (BACK)

031 BMSO 320GH/GLH.08.31 SHAFT TOWER 40*44*30032 BMSO 320GH/GLH.08.32 MIL BED

033 BMSO 320GH/GLH.08.33 M10*20 INBUS

9

ROLLER GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.09.01 M10*70 INBUS002 BMSO 320GH/GLH.09.02 FRONT FLAT003 BMSO 320GH/GLH.09.03 REAR FLAT004 BMSO 320GH/GLH.09.04 M10*40 INBUS005 BMSO 320GH/GLH.09.05 M10*30 INBUS006 BMSO 320GH/GLH.09.06 ROLLER CONNECTION FLAT( LEFT)007 BMSO 320GH/GLH.09.07 CHROME SHAFT (40 )008 BMSO 320GH/GLH.09.08 M6*30 INBUS009 BMSO 320GH/GLH.09.09 GUARD010 BMSO 320GH/GLH.09.10 FEEDER PISTON CONNECTION FLAT011 BMSO 320GH/GLH.09.11 M8*15 SETSKUR012 BMSO 320GH/GLH.09.12 CHROME SHAFT PART( LEFT)013 BMSO 320GH/GLH.09.13 M10*35 INBUS014 BMSO 320GH/GLH.09.14 MIDDLE FEED SUPPORT FLAT015 BMSO 320GH/GLH.09.15 SHAFT 25016 BMSO 320GH/GLH.09.16 M8*15 SETSKUR017 BMSO 320GH/GLH.09.17 SIX CORNER SHAFT 24018 BMSO 320GH/GLH.09.18 BEARING 6005019 BMSO 320GH/GLH.09.19 REAR CONNECTION FLAT020 BMSO 320GH/GLH.09.20 M10*30 INBUS021 BMSO 320GH/GLH.09.21 M6*30 INBUS022 BMSO 320GH/GLH.09.22 M8*35 INBUS023 BMSO 320GH/GLH.09.23 SUPPERT FLAT024 BMSO 320GH/GLH.09.24 M10*60 INBUS025 BMSO 320GH/GLH.09.25 PISTON FRONT COVER026 BMSO 320GH/GLH.09.26 DUST SEAL30*38027 BMSO 320GH/GLH.09.27 OIL SEAL30*40*8028 BMSO 320GH/GLH.09.28 ORING 42,86*3,53029 BMSO 320GH/GLH.09.29 BAND 2*10030 BMSO 320GH/GLH.09.30 PISTON SHAFT PIPE031 BMSO 320GH/GLH.09.31 SHAFT Q6032 BMSO 320GH/GLH.09.32 PISTON CHROME SHAFT033 BMSO 320GH/GLH.09.33 SEAL SETK18 050-034 (50*34*20,5)034 BMSO 320GH/GLH.09.34 PISTON REAR COVER035 BMSO 320GH/GLH.09.35 M6 NUT036 BMSO 320GH/GLH.09.36 REKOR 1/4 8037 BMSO 320GH/GLH.09.37 ROLLER CONNECTION FLAT (RIGHT)038 BMSO 320GH/GLH.09.38 M10*60 INBUS039 BMSO 320GH/GLH.09.39 ROLLER SHAFT PIPE040 BMSO 320GH/GLH.09.40 CHROME SHAFT CONNECTION PART ( RIGHT)

10

FEEDER PISTON GROUP

PART NMR PART CODE PART NAME001 BMSO 320GH/GLH.10.01 M10*25 INBUS

002 BMSO 320GH/GLH.10.02 DUAT SEAL 30*38003 BMSO 320GH/GLH.10.03 PISTON FRONT COVER

004 BMSO 320GH/GLH.10.04 M6*25 INBUS

005 BMSO 320GH/GLH.10.05 ORING 42,86*3,53006 BMSO 320GH/GLH.10.06 BAND 2*10

007 BMSO 320GH/GLH.10.07 OIL SEAL 30*40*8008 BMSO 320GH/GLH.10.08 CHROME SHAFT 30 'LUK

009 BMSO 320GH/GLH.10.09 PISTON SHAFT PIPE (50*60)

010 BMSO 320GH/GLH.10.10 SHAFT Q6*732011 BMSO 320GH/GLH.10.11 CHROME SHAFT 40

012 BMSO 320GH/GLH.10.12 CONNECTION PART013 BMSO 320GH/GLH.10.13 M10*25 INBUS

014 BMSO 320GH/GLH.10.14 M6 NUT015 BMSO 320GH/GLH.10.15 SEAL SET K18 050-034 (50*34*20,5)

016 BMSO 320GH/GLH.10.16 PISTON REAR COVER

017 BMSO 320GH/GLH.10.17 REKOR018 BMSO 320GH/GLH.10.18 1/4 REKOR

11

HYDRAULIC TENSİOİNG GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.11.01 PISTON COVER ( BACK)002 BMSO 320GH/GLH.11.02 SEAL SET 100X86X22,4003 BMSO 320GH/GLH.11.03 PISTON HEAD004 BMSO 320GH/GLH.11.04 PISTON SHAFT005 BMSO 320GH/GLH.11.05 Ø8 1/4" REKOR006 BMSO 320GH/GLH.11.06 SHAFT PIPE007 BMSO 320GH/GLH.11.07 LEAN PART (INNER) 008 BMSO 320GH/GLH.11.08 M12 INBUS009 BMSO 320GH/GLH.11.09 DUST SEAL 25X33X7,5 010 BMSO 320GH/GLH.11.10 BANT 2X10011 BMSO 320GH/GLH.11.11 O-RING 90X4012 BMSO 320GH/GLH.11.12 PISTON HOLDER013 BMSO 320GH/GLH.11.13 M12*40 INBUS014 BMSO 320GH/GLH.11.14 SLEDGE PLATES015 BMSO 320GH/GLH.11.15 WASHER016 BMSO 320GH/GLH.11.16 OIL SEAL 25X35X7017 BMSO 320GH/GLH.11.17 BANT 2X10018 BMSO 320GH/GLH.11.18 TENSIONING SLEDGE BLOCK019 BMSO 320GH/GLH.11.19 GREASE UNION020 BMSO 320GH/GLH.11.20 M12*50 INBUS021 BMSO 320GH/GLH.11.21 TENSIONING SLEDGE022 BMSO 320GH/GLH.11.22 WHEEL SHAFT023 BMSO 320GH/GLH.11.23 BEARING 30307024 BMSO 320GH/GLH.11.24 RING 472/80025 BMSO 320GH/GLH.11.25 IDDLE WHEEL026 BMSO 320GH/GLH.11.26 METAL RING 20*80027 BMSO 320GH/GLH.11.27 BEARING 30307028 BMSO 320GH/GLH.11.28 TENSIONING SHAFT COVER029 BMSO 320GH/GLH.11.29 MB6 SAFETY WASHER030 BMSO 320GH/GLH.11.30 KM6 NUT

OPTIONAL

12

HYDRAULIC VICE GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.12.01 KNOP BLOCKS002 BMSO 320GH/GLH.12.02 TENSIONING KNOP003 BMSO 320GH/GLH.12.03 TENSIONING SHAFT004 BMSO 320GH/GLH.12.04 BEARING T 77005 BMSO 320GH/GLH.12.05 METAL RING006 BMSO 320GH/GLH.12.06 WASHER 6 PC007 BMSO 320GH/GLH.12.07 42*86*3,53 ORİNG008 BMSO 320GH/GLH.12.08 LEAN BLOCK ( INNER)009 BMSO 320GH/GLH.12.09 34*59*2,62 ORİNG010 BMSO 320GH/GLH.12.10 LEAN BLOCK ( OUTER)011 BMSO 320GH/GLH.12.11 1/8 REKOR012 BMSO 320GH/GLH.12.12 M8*80 İNBUS013 BMSO 320GH/GLH.12.13 LEAN BLOCK

OPTIONAL

13

SENSETIVE PRESSURE GROUP -LEFTPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.13.01 BODY 002 BMSO 320GH/GLH.13.02 M4*20 INBUS003 BMSO 320GH/GLH.13.03 SHAFT004 BMSO 320GH/GLH.13.04 SHAFT TOWER005 BMSO 320GH/GLH.13.05 SPRING006 BMSO 320GH/GLH.13.06 UPPER COVER007 BMSO 320GH/GLH.13.07 M4*20 INBUS008 BMSO 320GH/GLH.13.08 REKOR 1/8 6

SENSETIVE PRESSURE GROUP-RIGHTPART NMR PART CODE PART NAME

009 BMSO 320GH/GLH.13.09 CHROME SHAFT010 BMSO 320GH/GLH.13.10 BODY011 BMSO 320GH/GLH.13.11 M4*20 INBUS012 BMSO 320GH/GLH.13.12 WASHER013 BMSO 320GH/GLH.13.13 CHROME SHAFT( UPPER)

OPTIONAL

14

TOP CLAMPING PISTON GROUPPART NMR PART CODE PART NAME

001 BMSO 320GH/GLH.14.01 PALET002 BMSO 320GH/GLH.14.02 PALET FLAT003 BMSO 320GH/GLH.14.03 M10*30 INBUS004 BMSO 320GH/GLH.14.04 FIXING PART005 BMSO 320GH/GLH.14.05 M10*35 INBUS006 BMSO 320GH/GLH.14.06 DUST SEAL 30*38007 BMSO 320GH/GLH.14.07 PISTON LOWER COVER008 BMSO 320GH/GLH.14.08 M6*25 INBUS009 BMSO 320GH/GLH.14.09 ORING 42,86*3,53010 BMSO 320GH/GLH.14.10 OIL SEAL 30*40*8011 BMSO 320GH/GLH.14.11 BAND 2*10012 BMSO 320GH/GLH.14.12 PIN Ø10*30013 BMSO 320GH/GLH.14.13 CHROME SHAFT 30 014 BMSO 320GH/GLH.14.14 SHAFT PIPE (50*60 )015 BMSO 320GH/GLH.14.15 SHAFT Ø6*415016 BMSO 320GH/GLH.14.16 REKOR017 BMSO 320GH/GLH.14.17 SEAL SET K18* 050-034 (50*34*20,5)018 BMSO 320GH/GLH.14.18 PISTON UPPER COVER019 BMSO 320GH/GLH.14.19 M6 NUT

OPTIONAL

15

16

17

18

19

20

21

22

23

24

25

26

1