HEWI | 1

Lift-up seats Range 801

Installation instructions US

2 | HEWI

33458

1314

Contents

User informationCare and cleaningWarning noticesProduct informationMountingDemountingBrake adjustment

HEWI support +1 646 405 10 32

HEWI | 3

Intended purposeThe HEWI lift-up seat is designed for use in bathrooms, especially showers. It providesa seat for persons with and without physical disabilities while taking a shower.

Exclusion of liabilityHEWI accepts no liability whatsoever for damage to persons or property that occurs or has occurred as a result of improper mounting or maintenance, particularly if the safety instructions and other points to note listed are not or have not been observed in full. HEWI accepts no liability whatsoever for damage occurring from incorrect cleaning.

Safety instructionsThese instructions are intended for qualified skilled personnel and the user of the installed product. Following installation, the instructions must be made available to the user.

• Follow with the installation instructions and instructions for use.

• In case of questions, problems, uncertainties or if damage occurs, contact the HEWI support service.

• Ensure that the product is installed, maintained and repaired by qualified, skilled personnel only.

• Check the product for damage on acceptance. Report defects immediately.

• Install/use the product only:

• in accordance with its intended purpose

• in its original condition without modifications

• in perfect condition

• Use original spare parts only.

• Only use HEWI fixing materials.

• Ensure that the wall structure and fixings are reinforced as required permanently to withstand the expected load.

• Only use in closed rooms.

User information Care and cleaning

Cleaning

• Clean the product as and when required.

• Follow the manufacturer's instructions regarding concentration, contact time, etc.

• Always apply the cleaning product on a cloth; do not apply it directly on the surface.

• Rinse with cold water immediately after cleaning.

• Note the material-specific information on suitable/unsuitable cleaning products.

• Try out all products on an inconspicuous area before use.

• Do not use any products with unknown composition.

• A detailed list of suitable cleaning products is available from our support service on request.

Unsuitable cleaning products

Ÿ Abrasive products/objects (e.g. scouring agents, scourer sponge, brushes, steel wool, microfibers, dirt erasers)

Ÿ Alkaline, acidic and chorine-based cleaning products, solvents

Ÿ Steam cleaners

Ÿ Do not treat metal components with objects containing iron (e.g. scourer sponge, steel wool).

DisposalDisposal of the product and packaging is subject to the relevant national regulations.

Ø 5/8"Tools required

2,5 mm4 mm6 mm!

This product uses metric socket screws.If using imperial hex keys, please choosean appropriate size.

Improper cleaning can cause damage to the surface and lead to injuries.Observe cleaning instructions listed below.

Risk of injuryCAUTION!

4 | HEWI

Improperly mounted lift-up seats (loose orat an angle) may lead to injuries due toslipping or falling.Make sure lift-up seats are installed securelyand in a horizontal position.

Risk of injuryCAUTION!

Exceeding the maximum load of the lift-up seat may lead to injuries due to falling.Observe maximum load.Ensure that the wall structure and fixings are reinforced as required permanently to withstand the expected load.

Risk of injuryCAUTION!

Warning notices

Any improper use, e.g. as a gymnasticapparatus or climbing aid, may lead toinjuries due to slipping or falling.Never step or jump on the seat.

Risk of injuryCAUTION!

450

OilFailing or improperly set brakes may lead to

injuries.Have the brakes checked and readjusted asrequired at least once a month.Do not use any kind of lubricant on the jointsor brake discs.

Risk of injuryCAUTION!

NOTICE

The surface of the seat is sensitive and cansuffer scratching caused by dust or dirt onor near the installation site.Keep the seat in its packaging wheneverpossible.Once the seat is installed, put the protectivefoil back around it until all construction workis done and the seat is ready to be used.

Risk of material damage

Maintenance

HEWI | 5

801.51US320R801.51US320L

801.51US330R801.51US330L

27

"

13

"9/ 1

6

28

"

1/ 2

322 /4"

15"

10

"

3/ 1

6right-sided version

right-sided version

10

"

3/ 1

6

322 /4"

13

"9/ 1

6

15"

33

"

3/ 1

6

Product information

6 | HEWI

801.51US450

801.51US440

21

"

13 /

16

10

"

3/ 1

6

15"

10

"

3/ 1

6

15"

20

"

1/ 1

6

29

"1 /

8

27

"

5 /16

Product information

HEWI | 7

801.51US460

801.US5152015

"1/ 4

10

"

3/ 1

63

3 "

15 / 1

6

15"

3

"

7/ 1

6

29 "1/8

17"

28 "1/4

Product information

8 | HEWI

801.51US320R

2 "1/4

13 "5/8 11 "13/16

13 "5/811 "13/16

2 "1/4

4 "15/16

801.51US320L

17½ - 19½" "

4 "15/16

17½ - 19½" "

FFL 17

" -

19

"

Mounting

HEWI | 9

801.51US330R

801.51US330L

2 "1/4

18 "5/16 11 "13/16

2 "1/4

18 "5/1611 "13/16

4 "15/16

4 "15/16

17½ - 19½" "

17½ - 19½" "

FFL 17

" -

19

"

Mounting

10 | HEWI

801.51US450

801.51US440

18 "3/4

2"

2"

26"

4 "15/16

4 "15/16

17½ - 19½" "

17½ - 19½" "

FFL 17

" -

19

"

Mounting

HEWI | 11

2"

30 "7/8

13 "15/16

1 "3/16

801.51US520

801.51US460

4 "15/16

4 "15/16

17½ - 19½" "

Top edge bathtub:13 (seat height 17" ") - 15 (seat height 1" 9")

9/16

9/16

FFL 17

" -

19

"

Mounting

12 | HEWI

M10x30

6 mm

H

FFL

Framing

1 2

3 4

The screw inserts must beflush with the finished wall.!

15

4/16

"

2"15

4/16

"

2"

2"2"

max. 14 ½

"

12"

Mounting

Ø 5/8"

H +

¾ "

H +

2 ¾

"

max. 14 ½"

HEWI | 13

6 mm

1 2

Demounting

To removePierce caps in the middle and prise off.

14 | HEWI

Brake adjustment

Clockwise: increase braking force Counter-clockwise: reduce braking force

The setscrew must be seated flush.

4 mm

!

1 2

3

4 5

2.5 mmM5

M52.5 mm

Check friction on bothsides of the seat.

HEWI | 15

16 | HEWI

www.hewi.com

Deutschland

HEWI Heinrich Wilke GmbH

Postfach 1260

D-34442 Bad Arolsen

Telefon: +49 5691 82-0

Telefax: +49 5691 82-319

info@hewi.de

M8010.02US 2020/01