© 2009 Avaya Inc. All rights reserved. IP Office control units and IP Office Expansion Modules.
-
Upload
mikaela-avary -
Category
Documents
-
view
231 -
download
1
Transcript of © 2009 Avaya Inc. All rights reserved. IP Office control units and IP Office Expansion Modules.
© 2009 Avaya Inc. All rights reserved.
IP Office control units
andIP Office Expansion Modules
IP Office control unitsand
IP Office Expansion Modules
IP Office 500 Version 2
IP Office 500 Version 2 is a modular communications solution that scales from 2 to 384 extensions and up to 1000 subscribers in a Small Community Network.
IP Office 500 Version 2
IP 500v2 Base Module
The IP500v2 control unit will support:
All existing IP500 plug in cards
All existing IP500 expansion modules.
The same IP400 expansion modules as the existing IP500
Combination Base Card (only supported in the IP500v2 Control Unit)
Power supplysocket
StatusLED‘s Slots for
SD-CardsExt.outputswitch
Ext. music-on-holdinput
RS232DTE port
LANPorts
ResetSD-CardSystem
Expansionports
Base Cards
The IP Office 500 Version 2 basic hardware can be fitted with up to a maximum of four slot-in base cards. Lines are connected using daughter cards that are plugged into these slot-in base cards.
IP Office 500 Version 2 Control Unit
IP Office 500 – base cards
Base card for DS terminals
Base card unit for analog telephones
VCM base card "Carrier" base card
4-Port Expansion Card
Combination Card
IP 500v2 Combination Card
Combines digital extensions (DS), analogue extensions (POTS), trunk ports (Analogue or BRI) and VCM channels.
Analogue trunk variant: 6 DS, 2 POTS, 4 Analogue trunk, 10 VCM
BRI trunk variant: 6 DS, 2 POTS, 4 BRI, 10 VCM
Maximum two per IP500v2
No support in IP500
Daughter Cards
Daughter cards for line connection are slotted into the IP Office 500 Version 2 plug-in base cards.
Eight Terminals
Line Connections
(Trunks)Analog, ISDN
BRI or PRI
IP Office 500 – daughter cards for base cards
Daughter cards for the IP Office 500 base cards:
IP Office 500 daughter card for analog lines4 ports
IP Office 500 daughter card for basic ports (BRI)2x ISDN or 4 x ISDN
IP Office 500 daughter card for primary multiplexer(PRI-U) 1x or 2 x PRI
IP 500v2 – Secure digital (SD-)card
SD Card Slots
System SD slot : Optional SD slot
700XXXXXX
IPO MU-LAW PCS0X
FK 1234567890
LOC
KSystem SD
•The SD card that is present in the System SD card slot will have a unique Feature Key number, the same as the Smart Card in the IP500, and will be used to•Validate licenses•Set companding law•Determines the system default operating mode : IP Office or PARTNER•System configuration•Core and expansion module binaries•Endpoint firmware•Embedded voicemail
Optional SD CardThe SD card that is present in the Optional SD card slot will:
Provide additional storage, for exampleVoicemail recordingsSystem logs
Provide an upgrade mechanismBackup medium for the System SD card.
Expansion Modules
If the number of ports available in the control unit through the base cards is not enough, expansion modules can be added to the system.
The IP Office 500 Version 2 system, supports a maximum of12 expansion modules.
IP500 Expansion Module
IP500v2 Control Unit
Expansion Modules (Continued)
IP Office 500 Version 2 supports up to 12 external expansion modules. These expansion modules provide additional connections for digital (DS) or analog telephones and analog lines.
IP500 BRI So8 Module
IP500 Analog Trunk 16 Module
IP500 Phone Expansion ModuleWith 16 or 30 Extensions
IP500 Digital Station ModuleWith 16 or 30 Extensions
Expansion Modules (Continued)
8 expansion modules are connected to the control unit on the back of the device. 4 expansion modules can be connected to a 4 Port Expansion Card.
Features of 4 Port Expansion Card
Some of the features of the 4 Port Expansion Card are:
It is a base card.
It doesn’t support Mezzanine cards (Trunks).
Only one card is allowed per IP Office 500 Version 2.
It is supported in slot 4 only.
It’s LED’s numbers will be labelled 1-12
Features of 4 Port Expansion Card (Cont.)
Some of the additional features of the 4 Port Expansion Cards are:
The 4 port expansion card can be used with the one meter expansion cables. The stack-up that is necessary for this to work is shown in the image here.
The 4 Port Expansion card can also work with longer, that is, two meter cables, to ease the installation. The color of the two meter cable will be yellow.
Four yellow cables will be supplied with every 4 Port Expansion Card. Side-view of a fully loaded system
with 12 expansion units and the expansion cables
Comparison with IP Office 412and IP Office 500
12*30=360
+3*8=24
=384
8*30=240
+4*8=32
=272
12*30=360DS or POT phone ports
384272360Total number of user/phone ports (inc DS, POT, IP)
3xdual = 180/144 4xdual = 240/192 2xdual = 120/96 Trunks (E1/T1 PRI)
64 ->12864128Conference channels
4448108Data channels
12812Expansion ports
IP Office 500 with 4 port expansion card
IP Office 500IP Office 412Capability
History
History
Take the slides follow up as anoverview about the previousIP Office versions!
IP Office 500 key card and flash card
With IP Office 500, the system and application licensing is carried out via key card.
As an option, it is possible to use a flash card to utilize Embedded VoiceMail.
IP Office 500 Base Module
IP Office can activate up to 12 expansion modules.
IP412
12 connection options for expansion modules
2 dedicated Layer 3 switch ports
60 simultaneous VoIP sessions
IP412 – front view
IP412 – rear view
412 trunk cards
412 daughter cards
IP400 OfficeVoice Compression Module 4/8/16/24
IP Office 406V2 Memory Card
IP400 Office Internal Modem Card
IP412 – Expansions
Trunk cards• IP400 Office Quad BRI• IP400 Office E1 PRI• IP400 Office E1 Dual PRI• IP400 Office Quad Analog Trunk
Internal• One or two IP400 Office Voice Compression Module with
4/8/16/24 channels• IP400 Internal Modem Card with 12 56k modems
External• Up to 12 expansion modules
Expansion Modules Overview
IP Office 412 supports twelve externalexpansion modules
• IP400 Office Phone Expansion Module
• IP400 Office Analog Trunk 16 Expansion Module
• IP400 Office Digital Station Expansion Module
• IP400 Office S08 Expansion Module
Connecting the expansion modules
The expansion modules are connected to the control unit at the rear of the device.
When connecting, always connect the expansion module to the power first. The control unit will be supplied last with the supply voltage. Due to an internal delay circuit in the control unit, all units can also be connected via a power strip.
IP400 Office Analog Trunk 16
These expansion modules support up to 16 analog lines. In the case of a power outage, the first two exchange lines of the module will automatically be switched to the rear of the unit.
IP400 Office Phone V2 Module
This module provides analog telephone interfaces (POT ports).The IP400 Office Phone V2 Module is available in three versions with 8, 16 or 30 extensions. Phones can be located up to 1 km away from the control unit. The Phone Expansion Module supports different methods of the notification function "Message waiting". These include: 81V, 101V, 51V stepped (pulsed) and line reversal.
IP400 OfficeDigital Station V2 Module
The IP400 Office Digital Station V2 Module is available in two versions with 8, 16 or 30 extensions.Phones can be located up to 1 km away from the control unit.
IP400 Office S08 Module
The IP400 Office S08 Module includes 8 S0-bus interfaces forbasic port ISDN devices.
The IP400 Office S08 Expansion Module supports point-to-point and point-to multipoint connections. A maximum of 10 TEIs (terminal IDs) is supported.