Post on 17-Jun-2020
PRL Glass systems inc. Phone: 800-433-7044 Fax: 626-968-9256 www.prlglass.comLLP
PRL GLASS SYSTEMS
Architectural Hardware
MADE IN THE USA
Architectural handles
Application
Suitable for frameless all glass doors, full framed clad doors, wood doors and aluminum doors.
•Swing doors: Center hung and offset doors.
•Sliding doors: Tiffany sliding system, Ruby sliding system, custom.
•Door thickness: Glass door 3/8” glass up to 3/4”.
In addition to glass doors, fittings are available for aluminum and Wood Doors up to 2-1/2” thick only upon request.
The locking mechanism can be engaged to on the floor by the use of a floor strike plate or a dust proof strike orit can lock on the top by using one of the recommended head strikes.
• DBSTOPdead bolt stop • DPSLdust proof strike - locking type or non locking type • MPS1manual panic strike - for single door • MPS2manual panic strike - for double door
Custom strikes available upon request.Please consult PRL Glass systems for details
Configurations
48LLP strike
on top
48LLP strike
on bottom
PRL Glass systems inc. Phone: 800-433-7044 Fax: 626-968-9256 www.prlglass.comLLP
PRL Glass systems inc. Phone: 800-433-7044 Fax: 626-968-9256 www.prlglass.com
MADE IN THE USA
3
interior handleset screws
interior handleset screws
interior handle
actuator shaft
exterior handle retainer
rubberwashers
rubber bushing
rubberwashers
rubberbushing
shoulder bolt
exterior handle
SFICsmall formatinterchangeable corewith key and control key
retainermetalwasher
shoulder boltmetal washer
1. PRODUCT NAME:48LLP Easy Lock Ladder Pull
2. MANUFACTURER:PRL Glass systems exclusively manufactures the easy lock ladder pull system as described on this sheet.
3. BASIC USE:PRL Glass systems 48LLP easy lock ladder pull system is a pre-engineered locking ladder pull system, shipped to the job site ready to install.
LIMITATIONS: 48LLP Easy Lock Ladder Pull system is only limited by the materials from which it is fabricated.
Pre-engineered 48LLP Easy Lock Ladder Pull should be assembled using the components listed:
48LLP ASSEMBLY:(1) 1-1/4” Diameter stainless steel exterior handle(1) 1-1/4” Diameter stainless steel interior handle(4) rubber washers(2) rubber bushing(4) Type 316 SS cup point socket set screw 1/4”-20 thread, 3/16” Length(1) Type 304 Stainless steel shoulder bolt 5/16”-18 thread1.4” length. (Length will vary with door thickness)(1) 360 free machining brass exterior handle retainer(1) 360 free machining brass actuator shaft assembly(1) retainer metal washer(1) shoulder bolt metal washer
FINISHES:Standard circular # 4 brushed or polished #8 finishes are available for stainless steel
MATERIAL:304 stainless steel alloy
GLASS HOLE REQUIRED:7/8” Diameter
4. INSTALLATION:The 48LLP Easy Lock Ladder Pull must be attached to surfaces that are approved or selected by the manufacturer and shall be detailed on all shop drawings
5. MAINTENANCE:The 48LLP Easy Lock Ladder Pull surface can be kept clean by the use of ordinary soaps and mild cleansers.Abrasive cleaners should not be used
6. TECHNICAL DATA:The 48LLP Easy Lock Ladder Pull has a fully concealed deadbolt locking mechanism that is operated at a comfortable height above the finished floor, no need to bend to unlock your door, it can be used to lock on the floor with the use of a dust proof strike or lock header/ceiling with the use of a LLP strike (consult PRL Glass for details )
48
114
6
6
PRL GLASS SYSTEMSEasy-Lock Ladder Pull
Product Data Sheet