VERTICAL MODULAR WASHERmembers.msaworld.com/wp-content/uploads/sites/3/... · WHIRLPOOL VERTICAL...

Post on 22-Mar-2020

9 views 1 download

Transcript of VERTICAL MODULAR WASHERmembers.msaworld.com/wp-content/uploads/sites/3/... · WHIRLPOOL VERTICAL...

WHIRLPOOL VERTICAL MODULAR WASHER

Presented by: Rick Kuemin, MSA Training Director www.msaworld.com

Brought to you by:

Whirlpool Model/Serial

Designations/Tech Sheet Location

Questions or comments? Please e-mail richard.kuemin@marcone.com

VMW Operation

Questions or comments? Please e-mail richard.kuemin@marcone.com

VMW Design

Questions or comments? Please e-mail richard.kuemin@marcone.com

Structure Changes

* Cabinet same as direct drive (separate back

panel). Cabinet is not removable

* Hung suspension (very stable platform)

Higher spin speeds

Reduces vibration/walking

* Basket does not float (WP # 14218862)

* No brake

* Gearcase attached to bottom with 4-10 mm bolts

Questions or comments? Please e-mail richard.kuemin@marcone.com

Transmission Operation

Questions or comments? Please e-mail richard.kuemin@marcone.com

Splutch

Questions or comments? Please e-mail richard.kuemin@marcone.com

Splutch Ass’y During Agitation

Splutch During Shifting

Splutch During Spin

Actuator-Lid Lock Mech. Operation

Questions or comments? Please e-mail richard.kuemin@marcone.com

1. Shifts from agitate to Spin

2. Monitors the position

3. Monitors motor RPM (speed wheel

in gearcase-optical sensor)

Lid Switch

Lock Switch

Latch Solenoid

LID LOCKED FOR ALL FUNCTIONS

VMW Control Panel

Questions or comments? Please e-mail richard.kuemin@marcone.com

1. Eco Monitor

2. Wash Cycle Dial

3. Options

4. Display

5. Sequencing Lights

Components – Top View

Questions or comments? Please e-mail richard.kuemin@marcone.com

Components – Top Lifted

Questions or comments? Please e-mail richard.kuemin@marcone.com

Components -- Bottom View

Questions or comments? Please e-mail richard.kuemin@marcone.com

Customer Viewable Codes

Questions or comments? Please e-mail richard.kuemin@marcone.com

There are three codes viewable by the customer

Long Fill (Wash LED ON)

Long Drain (Spin LED ON)

Lid Lock (Lid Lock LED Flashing)

Non Intuitive Control

Questions or comments? Please e-mail richard.kuemin@marcone.com

Note: Non Intuitive Control

helps keep customers from

inadvertently getting into the

test mode

Test Modes

Diagnostic Test Modes

Allow service tech to test and verify all inputs to the

machine control electronics

Do a quick and overall check of the washer before

going to a specific test—Don’t overlook the obvious

Questions or comments? Please e-mail richard.kuemin@marcone.com

Access Service Diagnostics

Questions or comments? Please e-mail richard.kuemin@marcone.com

Activation MUST be done within 6 seconds

Activation of Test Mode

Questions or comments? Please e-mail richard.kuemin@marcone.com

Correct Activation:

00 and all lights flashing

on/off

Note: To Exit Test at any time

Press Power Button. Washer will

automatically revert to normal operation

after 5 minutes of inactivity

Mode of Operation

Questions or comments? Please e-mail richard.kuemin@marcone.com

Test Mode will be identified with the

LEDs and/or the appropriate number in

the display

Fault Codes Display

Questions or comments? Please e-mail richard.kuemin@marcone.com

F#-type of Fault

E#-component system where

fault is located Fault Code Display: displays last 4

codes. Turn CCW 1 turn at a time to

view the most recent to oldest

Press/Hold START key 3

sec. to clear all faults

Note: a fault/error code will be removed from the memory if

it does not reoccur after 10 consecutive wash cycles

Fault Codes

Questions or comments? Please e-mail richard.kuemin@marcone.com

Fault Codes

Questions or comments? Please e-mail richard.kuemin@marcone.com

Fault Codes

Questions or comments? Please e-mail richard.kuemin@marcone.com

Fault Codes

Questions or comments? Please e-mail richard.kuemin@marcone.com

Automatic Test

Questions or comments? Please e-mail richard.kuemin@marcone.com

Automatic Test: Best done at the end of

service or at completion of the installation of the

product to make sure that everything is plugged

in and to verify proper operation

Turn the cycle selector

knob until Spin Light is

on and/or 02 is in the

display

Automatic Test

Questions or comments? Please e-mail richard.kuemin@marcone.com

Automatic Test

Manual Test

Note: Multiple outputs may

be activated simultaneously

Note: Outputs left on, will time out after 5 minutes

Turn cycle selector knob until Spin

and Done Lights are on and/or 03

is displayed

Manual Test

Manual Test

Calibration Mode

Turn cycle selector knob

until Rinse Light is on

and/or 04 is displayed

Calibrate When???

Calibrate when any of these

systems are replaced

Calibration Mode

Sales Mode

UI Mode Test

Main Control Board

Connectors and Pins

Valve Resistance Test

Resistance values of all valves are between 890-1300 Ohms

This will test the electrical connections and the valves themselves

Shifter Test

Shifter Voltages/Resistance Checks

Shifter Motor Control

AC output 120 VAC Shifter-Switch DC output

Shifter Motor resistance—J 16 pins 1-2 is

2K-3K ohms-Checks the resistance

through the harness and shifter motor

Always ensure plugs connections

are secure

Optical Sensor Circuit

Slowly turn the

basket by hand

Ohm the Harness

Line Voltage Path

Low Voltage Circuits

Drive Motor Neutral

Lid Lock

MUST be

closed to

provide the

motor neutral

Strip Circuit--Shifter

Strip Circuit--Shifter

Strip Circuit--Motor

Strip Circuit—Drain Pump

Removing Control Panel

Replacing User Interface

Adhered to Console

1 2

3

4

Removing Tub Top

Suspension Rods

Coin Trap

Reinstalling Basket

Reinstalling Basket

Reinstalling Basket

Shaft Seal

Harness Clips

Service Tips--Cycles

Service Tips--Cycles

Service Tips--Cycles

Cycle Chart

Now for the disassembly

and diagnostic testing