Post on 16-Sep-2019
UNIVERSITI TEKNIKAL MALAYSIA MELAKA
ENGINEERING DESIGN ANALYSIS ON 5KG PAYLOAD
GRIPPER FOR COMAU ROBOT
This report submitted in accordance with the requirements of the Universiti Teknikal
Malaysia Melaka (UTeM) for the Bachelor Degree of Engineering Manufacturing
(Robotic and Automation) with Honours.
By
BONG KUAN FUNG
FACULTY OF MANUFACTURING ENGINEERING
2009
UTeM Library (Pind.1/2007)
UNIVERSITI TEKNIKAL MALAYSIA MELAKA
BORANG PENGESAHAN STATUS LAPORAN PSM
JUDUL:
ENGINEERING DESIGN ANALYSIS ON 5KG PAYLOAD GRIPPER FOR COMAU ROBOT
SESI PENGAJIAN: Semester 2 2008/2009
Saya BONG KUAN FUNG mengaku membenarkan laporan PSM / tesis (Sarjana/Doktor Falsafah) ini disimpan di Perpustakaan Universiti Teknikal Malaysia Melaka (UTeM) dengan syarat-syarat kegunaan seperti berikut:
1. Laporan PSM / tesis adalah hak milik Universiti Teknikal Malaysia Melaka dan penulis.
2. Perpustakaan Universiti Teknikal Malaysia Melaka dibenarkan membuat salinan untuk tujuan pengajian sahaja dengan izin penulis.
3. Perpustakaan dibenarkan membuat salinan laporan PSM / tesis ini sebagai bahan pertukaran antara institusi pengajian tinggi.
4. *Sila tandakan (√)
SULIT
TERHAD
TIDAK TERHAD
(Mengandungi maklumat yang berdarjah keselamatan atau kepentingan Malaysia yang termaktub di dalam AKTA RAHSIA
RASMI 1972)
(Mengandungi maklumat TERHAD yang telah ditentukan oleh
organisasi/badan di mana penyelidikan dijalankan)
(TANDATANGAN PENULIS) Alamat Tetap:
NO. 324, KPG TAPAH,
BATU 22 ½, JLN KCH SERIAN,
94200 SARAWK.
Tarikh: _______________________
(TANDATANGAN PENYELIA)
Cop Rasmi:
Tarikh: _______________________
* Jika laporan PSM ini SULIT atau TERHAD, sila lampirkan surat daripada pihak organisasi berkenaan
dengan menyatakan sekali sebab dan tempoh tesis ini perlu dikelaskan sebagai SULIT atau TERHAD.
DECLARATION
I hereby, declared this report entitled “ENGINEERING DESIGN ANALYSIS ON
5KG PAYLOAD GRIPPER FOR COMAU ROBOT” is the result of my own
research except as cited in the references.
Signature : …………………………………
Author’s Name : BONG KUAN FUNG
Date : ………………………………...
APPROVAL
This report is submitted to the Faculty of Manufacturing Engineering of UTeM as a
partial fulfillment of the requirements for the degree of Bachelor of Manufacturing
Engineering (Robotic and Automation) with Honours. The members of the
supervisory committee is as follow:
………………………………………
(PSM Supervisor)
i
ABSTRACT
Gripper is general purpose robot hands, which are end effectors element in robot
applications, have been used widely in various industrial operations such as
transferring, assembling, and related manufacturing process. There are various
technological actuators of robot hands which give the power for the gripper motion.
Hydraulic, pneumatic and electrical motor system is very common actuator
technologies. In this paper, the engineering design analysis on 5kg payload gripper
for Comau robot is described. Finite element analysis is used to simulate deflections
of the gripper components under load to determine critical design parameters.
Besides that, gripper will also test under motion simulation. The system provides a
graphical and integrated environment for modeling and graphically simulating the
robot gripper when contact with the product. The result of the present study can be
used to developing the robot griper devices, optimizing their parameters and other
relevant aspects.
ii
ABSTRAK
Pencengkam merupakan penggunaan utama bagi tangan robot seperti mana
pencengkam tersebut akan disambungkan pada penghujung sesebuah tangan robot
untuk aplikasi tertentu bagi robot tersebut. Penggunaan gripper adalah luas dalam
pelbagai operasi industri seperti pemindahan barangan, pemasangan, dan
pengendalian dalam process pembuatan. Terdapat berbagai teknologi cara
mekanisme untuk gerakkan tangan robot yang memberi kuasa bagi pergerakkan
pencengkam. Contohnya, hidraulik, pneumatic, dan elektrik motor system adalah
mekanisme penggerak yang umum digunakan. Dalam projek ini, analisis rekabentuk
kejuruteraan terhadap 5kg muatan gripper untuk Comau robot akan dijalankan.
Analisis ‘finite element’ akan dilaksanakan bagi simulasi pesongan komponen
gripper apabila dikenakan muatan. Analisis tersebut penting bagi penentuan rekaan
parameter. Selain itu, simulasi pergerakan ataupun dikenali sebagai ‘motion
simulation’ juga akan dijalankan. Sistem tersebut memberi paparan grafik dan
intergrasi ruangan pergerakan untuk peragaan simulasi secara grafik terhadap
pencengkam bila mengendalikan tugas. Keputusan analisis akan digunakan untuk
perkembangan dan pernambahbaikan bagi parameter-parameter serta aspek-aspek
yang berkaitan.
iv
ACKNOWLEDGEMENT
There are many people who deserve thanks for the contributions they have made to
this project. Firstly, I would like to express my endless grateful to my Final Year
Project’s Principal Supervisor, Encik Khairol Anuar Bin Rakiman. He directed and
instructed me through every phase of the project, and his guidance has been
invaluable. He also spent time and effort helping to resolve new issue by giving
advice and suggestion as the project developed and checking the report a number of
times.
I would like to thank my beloved parent, for their abiding love and endless patience.
Their support has been constant and enduring through the process of this project.
They deserve an enormous amount of recognition for their moral support throughout
this project. I am also grateful for all of my friends, who had giving their help and
idea in completing this project. Finally, I am deeply indebted to the lab technician
and all of the people that had directly or indirectly helped me during the period of
completing the project. Thank you.
v
TABLE OF CONTENT
Abstract i
Abstrak ii
Dedication iii
Acknowledgement iv
Table of Content v
List of Tables viii
List of Figures ix
1. INTRODUCTION 1
1.1 Overview 1
1.2 Problem Statement 2
1.3 Objectives 3
1.4 Scope 4
2. LITERATURE REVIEW 5
2.1 Overview on Gripper 5
2.2 Gripper Operation 6
2.3 Gripping Action 6
2.3.1 Internal Gripping 6
2.3.2 External Gripping 7
2.3.2.1 Friction Gripping (Force closure) 7
2.3.2.2 Retention or Encompassing Gripping (Form closure) 7
2.4 Classification of Common End Effectors 8
2.4.1 Passive End Effectors 9
2.4.1.1 Non-Prehensile Gripper 9
2.4.1.2 Warp Gripper 10
vi
2.4.1.3 Pinch Gripper 10
2.4.2 Active End Effectors and Hands 11
2.5 Component Features Considered In the Selection Process 12
2.5.1 Weight of Component 12
2.5.2 Material of Compoment 13
2.5.3 Surface Properties of the Component 13
2.5.4 Geometry of the Components 14
2.5.5 Gripper Features Considered In the Selection Process 16
2.5.6 Number of Different Components 17
2.5.7 Positional accuracy 17
2.5.8 Cycle Time 17
2.5.9 Environmental Conditions 18
2.5.10 Weight of Gripper 19
2.5.11 Gripping Force 19
2.5.12 Actuation Principle 20
2.5.13 Range of Jaw Openings 22
2.5.14 Area of Contact 22
2.5.15 Cost 22
2.6 Gripper Selection Process 23
2.6.1 Gripper Types Consideration in the Selection Process 23
2.6.1.1 Clamping Grippers 23
(a) Two-jaw Grippers 24
(b) Three-jaw Grippers 24
2.6.1.2 Flexible Grippers 25
(a) Multifingered Grippers 25
(b) Soft Grippers 26
(c) Bladder Grippers 27
(d) Adjustable-Jaw Grippers 28
(e) Single-Surface Grippers 29
(f) Magnetic grippers 29
vii
(g) Vacuum Gripper 30
(h) Adhesive Gripper 31
2.7 Conclusion 32
3. METHODOLOGY 33
3.1 Overview 33
3.2 Clarification of Task 35
3.3 Conceptual Design 35
3.4 Embodiment Design 36
3.5 Detail Design 36
4. GRIPPER DESIGN 37
4.1 Overview 37
4.2 Evaluation on Existing Gripper 38
4.3 Combination Solution Principles to Fulfill the Overall Function 40
4.4 Technical Rating Rt and Economical Rating Re 42
4.5 Selection Suitable Combinations 45
4.6 Improvement Base on Solution Variants 47
4.6.1 Improvement on Base 47
4.6.2 Improvement on Support Bar 47
4.6.3 Improvement on Slider 48
4.6.4 Improvement on Jaw 48
4.7 Optimization on gripper design 49
4.7.1 Optimization on gripper’s jaws 49
5. RESULT AND DISCUSSION 56
5.1 Overview 56
5.2 Formation of Conceptual Design 57
5.3 Griper Feature 58
5.3.1 Stability 58
viii
5.3.2 Low Cost 58
5.3.3 Minimum Gripper Weight 58
5.3.4 Flexibility 59
5.3.5 Easy of Assembly or Disassembly 59
5.4 Parts and Function of New Design 60
5.5 Cylinder Selection 62
5.6 Design Analysis 66
5.6.1 Force Acting on Parts 66
5.6.1.1 Moment Inertia of Holder with Jaws 67
5.6.1.2 Force Acting on Robot Mount 69
5.6.1.3 Force Acting on Gripper Mount 70
5.6.1.4 Force Acting on Bracket 70
5.6.1.5 Force Acting on Support 70
5.6.1.6 Force Acting on Base 71
5.6.1.7 Force Acting on Holder 71
5.6.1.8 Force Acting on Slider 72
5.6.1.9 Force Acting on Jaw 72
5.6.1.10 Force Acting on Rod 72
5.6.2 Design Analysis Using Software 73
5.7 Design Simulation 80
5.8 Conclusion on Result Obtain 80
6. CONCLUSION 84
6.1 Further Improvement Works and Suggestion 85
REFERENCES 86
ix
APPENDICES
A Engineering Drawing For Gripper
B Stress analysis on Gripper Parts
C Data Sheet for Pneumatic Cylinder
x
LIST OF TABLES
Table 2.1. Summarize of part characteristics and associated end
effector solutions. 14
Table 2.2a. Lower Power Actuator Principles. 20
Table 2.2 b. Comparison between common actuators. 21
Table 4.1 Existing griper parts and function. 39
Table 4.2 Combination scheme for different solution principle. 41
Table 4.3 Technical rating for variants. 43
Table 4.4 Economic rating for variants. 43
Table 4.5 Operation sequence for existing gripper design. 50
Table 4.6 Operation sequence for new gripper’s jaw design. 52
Table 5.1 New gripper parts and function. 60
Table 5.2 Parts quantities and weights. 61
Table 5.3 Cylinders characteristic and specification. 64
Table 5.4 Evaluation on cylinders. 65
Table 5.5 Result of base design analysis. 77
Table 5.6 Summarize result of design analysis for griper parts. 78
Table 5.7 Simulation of gripper attached on Comau robot. 80
xi
LIST OF FIGURES
Figure 2.1. Types of gripper action. 6
Figure 2. 2. External griping action. 8
Figure 2.3. A classification of the basic end effectors types. 8
Figure 2.4. A noncontact end effector for acquiring and transporting
delicate wafers. 9
Figure 2.5. Compliant pneumatic gripper executes a gentle wrap grasp. 10
Figure 2.6. A gripper with pivoted fingers designed. 11
Figure 2.7. Two-finger servo gripper with force sensing and
changeable fingertips. 12
Figure 2.8. Type of power driven shown in force versus speed. 21
Figure 2.9. Gripper classification for selection process. 23
Figure 2.10a. Two-jaw grippers. 24
Figure 2.10b. Three-jaw grippers. 24
Figure 2.11. Flexible gripper material handling. 25
Figure 2.12. Multifingers gripper material handling. 26
Figure 2.13. The flexible gripping action of the soft gripper. 27
Figure 2.14. Pulley-and-wire mechanism for soft finger. 27
Figure 2.15. Bladder Clamps handle fragile products gently. 28
Figure 2.16. (a) Adjustable jaw with laminated plate cams.
(b) Flexibility of jaw stacks arrangement.
(c) Gripping odd shaped work piece. 29
Figure 2.17. Magnetic gripper, handling ferromagnetic workpieces. 30
Figure 2.18. Type of vacuum gripper. 30
Figure 2.19. Adhesive gripper for fabric handling. 31
xii
Figure 3.1 Flow of Work for Design and Analysis Process. 34
Figure 4.1 Existing gripper design. 38
Figure 4.2 Comparison of the technical and economic rating of the
concept variants. 44
Figure 4.3 Selection of combinations of solution principles (variants). 46
Figure 4.4 Optimization on gripper’s jaw. 51
Figure 4.5 Bottom view of gripper’s jaw arrangement. 52
Figure 4.6 Optimized gripper operates with roller conveyor. 53
Figure 4.7 Holder. 54
Figure 4.8 Rubber pad. 55
Figure 5.1 Conceptual design. 57
Figure 5.2 Forces acting on gripper. 62
Figure 5.3 Rotation of holder. 67
Figure 5.4 Force acting on robot mount. 69
Figure 5.5 Force acting on gripper mount. 70
Figure 5.6 Force acting on bracket. 70
Figure 5.7 Force acting on support. 70
Figure 5.8 Force acting on base. 71
Figure 5.9 Force acting on holder. 71
Figure 5.10 Force acting on slider. 72
Figure 5.11 Force acting on jaw. 72
Figure 5.12 Force acting on rod. 72
Figure 5.13 Forces acting at the base. 73
Figure 5.14 Stress occur on base due to applied forces. 74
Figure 5.15 Displacement changes due to applied forces. 75
Figure 5.16 Strain analyses due to applied forces. 76
Figure 5.17 Design check on factor of safety. 77
1
CHAPTER 1
INTRODUCTION
1.1 Overview
According to dictionary of McGraw-hill(2003), gripper is define as a component of
robot that grasp an object, generally through the use of suction cups, magnets, or
articulated mechanism. Gripper provides the capacity to do a wide variety of
manipulative task. Robotic hand or gripper is the integral part in most of the robot
application. A robot arm itself can serve no purpose until a load or a tool is
suspended from or attached to it. The robotic application in assembly and material
handling is growing more rapidly in industrial environment. Thus, design of robotic
gripping mechanism always becomes the key element for a specific operation.
The main function of a gripper is to grasp and to release workpieces during the
material transfer route. Generally, the gripper for industrial robots is a specialized
device that is used to handle only one or a few objects of similar shape, size and
weight in a repetitive operation, which requires minimum gripping dexterity and is
limited in its versatility. However, in other applications, the robot gripper will be
required to handle many different objects of varying weights, shapes, and material.
Then, we shall refer to a more universal or versatile grippers. Gripper types will be
discussed furthers in literature review.
2
The gripper is the mechanical interface between the robot and the work and the
device with which the robot performs its programmed handling functions. Correctly
selecting the gripper for an application is essential to the success of the application.
Arthur G. Erdman (1986) explained that gripper selection is a may not be an easy
task since there are wide variety of gripper types and configurations and many
different factors to consider. Information on the factors which are relevant to the
selection process is incomplete and tends to be qualitative. The material available
and ease or manufacturing is also an important consideration.
In this study, a robot gripper that has been design by the previous students is required
be to fully analyses for its physical properties when handling load. Solid Work will
be use as the analysis software for finite element analysis to the gripper. Finally, the
gripper has to go through workspace testing by using simulation software to observe
its performance in real time working situation.
1.2 Problem Statement
The design analysis of robotic gripper is highly complex and environment dependent.
To deal with complexity, the entire design project has to be broken down into several
sub problems which are then treated independently as optimization problem.
However, the constraints are generally dependent on each other. Its also appear that
more than one constraint have to be minimize simultaneously. It may require
minimize weight of gripper and the stability of the grasp.
The study of this project is focus on improvement and continuation work on the
previous PSM project which is a 10kg payload gripper for Comau robot. Basically
the gripper design has been carried out in the last PSM. Since the current task is
design analysis on 5kg payload gripper for Comau robot, this mean there would be a
reducing in weight of payload from previous design while maintains it efficiency.
3
Often, very little time is spent in optimal kinematics structure design in the early
stages of a design process. D. T. Pham (1988) describes that a time pressures
sometimes force engineers to repeat topologies that have worked in similar
application in the past rather than try to create better design. It is always encourages
to follow the previous design unless the design analysis really proven that it was not
good. Thus, modification and optimization are requires to upgrade the design to
achieve a better performance.
Generally, a physical prototype is necessary to truly test a hand’s ability to perform
tasks, but this can be quite costly and design changes are not easy to make. Thus it
would need a simulation system that able to load a gripper hand design, to interact
with it and perform grasps of objects, and to visualize and evaluate the space of
performance and error that might occurs.
1.3 Objectives
The objective of this project is to design analysis the existing design gripper to
perform a pick and place operation for 5kg payload boxes. Below are important
objective has to be achieved:
a) Analysis on existing design
b) Finalize complete engineering design analysis and relevant aspects
c) Simulate the gripper performance
4
1.4 Scope
The scope is focused on related aspect in this project so that the objectives are able to
accomplish. Scope on this project will cover up the below task:
a) Improvement on existing design or drawing.
b) Design analysis on finite element using SolidWorks.
c) Run complete simulation on predefined layout.
5
CHAPTER 2
LITERATURE REVIEW
2.1 Overview on Gripper
A gripper is a device that grasps, retains and eventually releases a workpiece. It can
hold, tighten, handle and release an object just like a human hand. It can be attached
to a robot or be part of a fixed automation system. Because this component handles
the workpiece, the gripper must be selected and applied carefully. The design and
construction of highly dexterous robot hands has been a major research and
development objective for at least the past two decades. It was inspired by the
well-known Utah/MIT robot hands during the 1980’s explained by S .C. Jacobson
(1986).
The analysis of mechanical fixture and jig goes back to the work of Releaux (1875).
He analyzed the condition under which object or part can be completely restrained
and define form closure. While gripper and fixture have been used extensively in
industry, the field of robot grasping started with the work of Asada and Hanfusa
(1979) first attempts to develop three fingered robotic hand.
6
2.2 Gripper Operation
Consider an object grasped at a contacts, it is generally assumed that all contacts are
point contacts and idealizations such as a line or surface contact can be approximated
by two ore more point contacts. Each point contact can be modeled as either a
frictionless point contact, a frictional point contact, or a soft contact. A frictionless
contact is defined as a contact in which the finger can only exert force along common
normal at the point of contact. A frictional contact is contact that can transmit both a
normal force and a tangential force at the point of contact. While soft contact also
allows the finger to exert a pure torsion moment about common normal at the point
of contact.
2.3 Gripping Action
2.3.1 Internal Gripping
In some applications, the object geometry or the need to access the exterior of the
object will require that the object is held from the center. In this case the opening
force of the gripper will be holding the object. Figure 2.1 below shown an internal
and external grip.
Figure 2.1: Types of gripper action.
7
2.3.2 External Gripping
This is the most popular method of holding objects, it is the most simplistic and it
requires the shortest stroke length. When the gripper jaws close, the closing force of
the gripper holds that object.
External gripping action can be classified into two categories as shown in Figure 2.1.
2.3.2.1 Friction Gripping (Force Closure)
Friction gripping relies totally on the force of the gripper to hold the part. They are
the easiest to fabricate and may require more force to hold the object. This is
especially useful for objects that do not have flat surfaces. Parts can be removes by
forces applied from any direction. The coefficient of friction between the workpiece
and the gripper fingers can vary greatly depending on the material and surface finish.
For consistency in sizing purpose, the recommended coefficient of friction always is
0.25. Force closure is also known as frictional contact since it transmits both a
normal force and a tangential force at the point of contact.
2.3.2.2 Retention or Encompassing Gripping (Form closure)
The gripping jaws will hold the object and support it in the jaws. It is the preferred
method since it adds stability to holding the object and requires less force to hold the
object, to drop the object we must overcome the force to open the jaws. The travel
stroke of the gripper may have to be increased to encompass the object. While an
encompassing grip is preferred, less pressure required to grip the part, more stable
during movement throughput the work cell. It can be consider as a line or surface
contact can be approximated by two or more point contacts.