Post on 11-Mar-2020
Engineered Products for Robotic ProductivityPinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: +1-919.772.0115 • Fax: +1-919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com
TSM Tool Stand
Manual
Document #: 9610-20-1114
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 2
ForewordPlease contact ATI Industrial Automation with any questions concerning your particular model.
CAUTION: This manual describes the function, application, and safety considerations of this product. This manual must be read and understood before any attempt is made to install or operate the product, otherwise damage to the product or unsafe conditions may occur.
Information contained in this document is the property of ATI Industrial Automation, Inc. (ATI) and shall not be reproduced in whole or in part without prior written approval of ATI. The information herein is subject to change without notice. This manual is periodically revised to reflect and incorporate changes made to the product.
The information contained herein is confidential and reserved exclusively for the customers and authorized agents of ATI Industrial Automation and may not be divulged to any third party without prior written consent from ATI. No warranty including implied warranties is made with regard to accuracy of this document or fitness of this device for a particular application. ATI Industrial Automation shall not be liable for any errors contained in this document or for any incidental or consequential damages caused thereby. ATI Industrial Automation also reserves the right to make changes to this manual at any time without prior notice.
ATI assumes no responsibility for any errors or omissions in this document. Users’ critical evaluation of this document is welcomed.
Copyright by ATI Industrial Automation. All rights reserved.
How to Reach Us
Sale, Service and Information about ATI products:
ATI Industrial Automation 1031 Goodworth Drive Apex, NC 27539 USA WWW.ati-ia.com Tel: 919.772.0115 Fax: 919.772.8259 E-mail: info@ati-ia.com
Technical support and questions:Application Engineering Tel: 919.772.0115, Option 2, Option 2 Fax: 919.772.8259 E-mail: mech_support@ati-ia.com
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 3
Table of ContentsForeword .......................................................................................................................................... 2Glossary ........................................................................................................................................... 61. Safety ......................................................................................................................................... 7
1.1 ExplanationofNotifications ......................................................................................................... 7
1.2 General Safety Guidelines ............................................................................................................ 7
1.3 Safety Precautions ........................................................................................................................ 8
2. Product Overview ..................................................................................................................... 92.1 TSM System with Pin and Bushing Style Mounting ................................................................... 9
2.1.1 Post Module Kits .............................................................................................................. 10
2.1.2 Horizontal Modules ........................................................................................................... 10
2.1.3 Horizontal Extensions ....................................................................................................... 10
2.1.4 TSM Adapter Module ........................................................................................................ 10
2.1.5 Pin and Bushing Mounting Module ................................................................................... 11
2.1.6 Tooling Interface Plates .................................................................................................... 11
2.1.7 RetrofitLockingAssembly ................................................................................................ 11
2.1.8 PinandBushingLockingMountingModule ..................................................................... 12
2.1.9 ToolingInterfacePlatesLocking ....................................................................................... 12
2.1.10 Proximity Sensor Modules ................................................................................................ 12
2.2 TSM System with V-Block Style Mounting ................................................................................ 132.2.1 Post Module Kits .............................................................................................................. 14
2.2.2 Horizontal Modules ........................................................................................................... 14
2.2.3 Horizontal Extensions ....................................................................................................... 14
2.2.4 TSM Adapter Module ........................................................................................................ 14
2.2.5 Mounting Modules ............................................................................................................ 15
2.2.6 Tooling Interface Plates .................................................................................................... 15
2.2.7 Vertical Mounting Module ................................................................................................. 16
2.2.8 Vertical Tooling Interface Plate ......................................................................................... 16
2.2.9 Sensor Holders ................................................................................................................. 16
2.2.10 Proximity Sensor .............................................................................................................. 16
2.3 TSM System with Tool Hanger Mounting Module .................................................................... 172.3.1 Post Module Kits .............................................................................................................. 17
2.3.2 Horizontal Modules ........................................................................................................... 17
2.3.3 Tool Hanger Mounting Modules ........................................................................................ 18
2.3.4 Tool Hangers .................................................................................................................... 18
2.3.5 Proximity Sensor and Cables for Tool Hanger Mounting Module ..................................... 18
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 4
2.4 Post Module Components .......................................................................................................... 192.4.1 Base Plate ........................................................................................................................ 19
2.4.2 Rail Assemblies ................................................................................................................ 19
2.4.3 Gusset Assembly .............................................................................................................. 19
2.5 DeterminingTheToolStandConfiguration .............................................................................. 202.5.1 ConfiguringaTSMSystemwithHorizontalMounting ...................................................... 21
2.5.2 ConfiguringaTSMSystemwithPinandBushingMounting ............................................ 21
2.5.3 ConfiguringaTSMSystemwithVerticalMounting .......................................................... 22
2.5.4 ConfiguringaTSMSystemwithToolHangerMounting ................................................... 22
3. Installation .............................................................................................................................. 233.1 Installing Base, Rail, and Gusset assemblies .......................................................................... 23
3.2 Installing Pin and Bushing or Horizontal V-Block Mounting Module to Tool Stand ............. 25
3.3 Installing Vertical V-Block Mounting Module to Tool Stand .................................................... 27
3.4 Installing Tool Hanger Mounting Module to Tool Stand .......................................................... 28
3.5 Installing Horizontal Extension to Tool Stand .......................................................................... 29
3.6 Proximity Sensor Module Installation for Pin and Bushing TSM Systems ............................ 30
3.7 Proximity Sensor Installation for V-Block TSM Systems (Sensor Holder - 9120-TSM-SM-4205) ........................................................................................ 31
3.8 Proximity Sensor Installation for V-Block TSM Systems (Sensor Holder - 9120-TSM-SM-4206) ........................................................................................ 32
3.9 Proximity Sensor installation for TSM Tool Hanger ................................................................. 33
4. Operation ................................................................................................................................ 344.1 TSM System with Pin and Bushing Style Mounting Operation ............................................... 34
4.2 TSM V-Block Systems Operation ............................................................................................... 35
4.3 TSM Tool Hanger System Operation ......................................................................................... 35
5. Maintenance ............................................................................................................................ 365.1 All TSM Systems ......................................................................................................................... 36
5.2 Pin and Bushing TSM Systems .................................................................................................. 375.2.1 Clean,Lubricate,andReplaceAlignmentPinsandBushings ......................................... 37
5.3 TSM V-Block Systems ................................................................................................................. 38
5.4 TSM Tool Hanger Systems ......................................................................................................... 39
6. Troubleshooting ..................................................................................................................... 407. Serviceable Parts ................................................................................................................... 41
7.1 Part Number Cross Reference ................................................................................................... 427.1.1 TSMV-BlockSystems ...................................................................................................... 42
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 5
8. Specifications ......................................................................................................................... 438.1 Common TSM System Components ......................................................................................... 43
8.2 TSM Pin and Bushing System Components ............................................................................. 43
8.3 TSM V-Block System Components ............................................................................................ 43
8.4 TSM Tool Hanger System Components .................................................................................... 43
9. Drawings ................................................................................................................................. 449.1 Pin and Bushing Mounting Module ........................................................................................... 44
9.2 Pin and Bushing QC-50 Tooling Plate ....................................................................................... 45
9.3 Pin and Bushing QC-76 Tooling Plate ....................................................................................... 46
9.4 Pin and Bushing QC-110 Tooling Plate ..................................................................................... 47
9.5 Pin and Bushing Horizontal Blank Tooling Plate ..................................................................... 48
9.6 TSM Pin & Bushing Mounting Module - Rigid - Locking ......................................................... 49
9.7 PinandBushingRetrofitLockingAssembly ............................................................................ 50
9.8 Horizontal Tooling Interface Plate-Blank (Locking) ................................................................. 51
9.9 Tooling Interface Plate for QC 40- Blank- MA03 (Locking) ...................................................... 52
9.10 Vertical Tooling Interface Plate - Blank (Locking) .................................................................... 53
9.11 Mounting Module 3597 ................................................................................................................ 54
9.12 Mounting Module 4018 ................................................................................................................ 55
9.13 QC-40 Tooling Interface Plate .................................................................................................... 56
9.14 QC-41 Tooling Interface Plate .................................................................................................... 57
9.15 QC-60 Tooling Interface Plate .................................................................................................... 58
9.16 QC-62 Tooling Interface Plate .................................................................................................... 59
9.17 QC-71 Tooling Interface Plate .................................................................................................... 60
9.18 QC-76 Tooling Interface Plate .................................................................................................... 61
9.19 QC-100 Tooling Interface Plate .................................................................................................. 62
9.20 Blank Tooling Interface Plate ..................................................................................................... 63
9.21 Vertical Mounting Module 4068 .................................................................................................. 64
9.22 Vertical Mounting Module 4070 .................................................................................................. 65
9.23 Vertical Tooling Interface Plate - Blank ..................................................................................... 66
9.24 Vertical Tooling Interface Plate - Blank (Large) ........................................................................ 67
9.25 Tool Hanger Module 5496 ........................................................................................................... 68
9.26 Tool Hanger Module 5891 ........................................................................................................... 69
9.27 Tool Hanger Module 5923 ........................................................................................................... 70
9.28 Tool Hanger Module 5497 ........................................................................................................... 71
9.29 Post Modules ............................................................................................................................... 72
9.30 TSM Rail Adapter Module - V-Block Style ................................................................................. 73
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 6
9.31 Sensor Holders ........................................................................................................................... 76
9.32 Receiver Blocks ........................................................................................................................... 79
9.33 Tooling Pins ................................................................................................................................. 80
9.34 Medium Tool Stand General Overview ...................................................................................... 81
10. Terms and Conditions of Sale ............................................................................................... 82
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 7
GlossaryTerm Definition
Alignment Pins The alignment pin attaches to the tooling interface plate or a tool hanger module.
Adapter module The adapter module provides a mounting surface for a mounting module to be attached to a post module or end of a horizontal extension.
End-Effector Atoolorotherdeviceattachedtotherobotarminordertoperformatask.Horizontal module A horizontal rail that supports multiple tool positions.
Master plate The half of the Tool Changer that is mounted to an interface plate, robot or end-effector adjacent to the robot.
Modules Optional components that can be added to the Master and Tool plates to enhance the capabilities of the Tool Changer, e.g. Fluid/Air, Electrical, DeviceNet, Servo, High-Current.
Mounting module Provides a mount on the tool stand for the tooling interface plate or can mount theToolChangerToolplatedirectlyforsomespecificmodels.
Pin and Bushing Mounting Tool stand that uses mounting modules with pins and bushing to support and accurately locate the Tool Changer Tool plate and customer tooling.
Post module Combines the base, vertical rail, and gusset assemblies into a group of components.
Proximity Sensor Provides a signal indicating the tool is located in the tool stand.
Sensor Holder The sensor holder provides a mounting on the tool stand for the proximity sensor.
Tooling Interface Plate A machined plate that adapts the Tool body to an end-effector, and provides mounting features for a tool stand.
Tool Hanger ThehalfoftheToolChangerthatismountedtotheflatontheToolChanger.
Tool plate The half of the Tool Changer that is mounted to a tooling interface plate or customer-supplied tooling.
Tool Stand AfixtureprovidedbyATIforholdingoftheToolplatewhennotinuse.
Horizontal Extension Afixturethatprovidesmoretoolclearanceforthecustomertoolingthanthestandard TSM post module.
Vertical Mounting module Provides a mount on the tool stand for the vertical tooling interface plate or can mounttheToolChangerToolplatedirectlyforsomespecificmodels.
Vertical Tooling Interface Plate
A machined plate with a vertical surface that adapts the customer tooling and provides mounting features for a tool stand.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 8
1. SafetyThe safety section describes general safety guidelines to be followed with this product, explanation of the notifications found in this manual, and safety precautions that apply to the product. More specific notifications are embedded within the sections of the manual where they apply.
1.1 ExplanationofNotificationsThe notifications included here are specific to the product(s) covered by this manual. It is expected that the user heed all notifications from the robot manufacturer and/or the manufacturers of other components used in the installation.
DANGER: Notificationofinformationorinstructionsthatifnotfollowedwillresultindeathorseriousinjury.Thenotificationprovidesinformationaboutthenatureofthehazardous situation, the consequences of not avoiding the hazard, and the method for avoiding the situation.
WARNING: Notificationofinformationorinstructionsthatifnotfollowedcouldresultindeathorseriousinjury.Thenotificationprovidesinformationaboutthenatureofthehazardous situation, the consequences of not avoiding the hazard, and the method for avoiding the situation.
CAUTION: Notificationofinformationorinstructionsthatifnotfollowedcouldresultinmoderateinjuryorwillcausedamagetoequipment.Thenotificationprovidesinformation about the nature of the hazardous situation, the consequences of not avoiding the hazard, and the method for avoiding the situation.
NOTICE: Notificationofspecificinformationorinstructionsaboutmaintaining,operating,installation, or setup of the product that if not followed could result in damage to equipment. The notificationcanemphasizebutisnotlimitedtospecificgreasetypes,goodoperatingpractices,or maintenance tips.
1.2 General Safety GuidelinesThe TSM system is intended to for use in industrial applications for tool changing and storage and therefore requires the use of a Tool Changer.Prior to purchase and installation, the customer should verify that the Tool Changer selected is rated for the maximum loads and moments expected during operation. Refer to the customer’s Tool Changer manual or contact ATI for assistance.
WARNING: The customer is responsible for ensuring that the area between the tool and the Tool Stand is clear of foreign objects during tool drop-off. Failure to do so may result in serious injury to personnel.
WARNING: The gap between the Master and Tool sides is a pinch point. All personnel should be prevented from placing any part of their body or clothing in the gap, especially during actuation of the tool hanger mechanism.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 9
1.3 Safety PrecautionsWARNING: Do not perform maintenance or repair(s) on the Tool Changer or modules unless the Tool is safely supported or placed in the tool stand, all energized circuits (e.g. electrical, air, water, etc.) are turned off, pressurized connections are purged and power is discharged from circuits in accordance with the customer’s safety practices and policies. Injury or equipment damage can occur with the Tool not placed and energized circuits on. Place the Tool in the tool stand, turn off and discharge all energized circuits, purge all pressurized connections, and verify all circuits are de-energized before performing maintenance or repair(s) on the Tool Changer or modules.
WARNING: Duringoperation,theareabetweentheMasterandToolmustbekeptclear.FailuretokeepareaclearwillresultindamagetoToolChanger,modules,orend-of-arm tooling and could cause injury to personnel.
CAUTION: The TSM system is only to be used for intended applications and applications approved by the manufacturer.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 10
2. Product OverviewThe ATI TSM (Tool Stand Medium) system is compatible with ATI Tool Changer sizes QC-20 through QC-110. The stand is designed to fit most customer applications. The modular system allows for you to essentially “build your own” tool storage rack based on the number of tools, desired positioning, and mounting arrangements. There are three types of TSM systems available:
• Section 2.1—TSM System with Pin and Bushing Style Mounting• Section 2.2—TSM System with V-Block Style Mounting• Section 2.3—TSM System with Tool Hanger Mounting Module
For the most current product information on the TSM systems, click the following link: TSM Systems
2.1 TSM System with Pin and Bushing Style MountingThe pin and bushing modules are a rigid mounting system. Horizontal and vertical tooling interface plates mount to customer tooling.
Figure 2.1—TSM System with Pin and Bushing Style Mounting
QC Tool Plate
Horizontal Module
Tooling Interface Plate
Locking Vertical Tooling Plate
Locking Mounting Module
Mounting Module
Horizontal Adapter
Proximity Sensor
Post Module
Proximity Sensor
Adapter Plate
Vertical Tooling Plate
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 11
2.1.1 Post Module KitsThe post module kit is a common component to all TSM systems. The post module kit is available in different post heights and combines the base, rail, and gusset assemblies into a group of components.
Item Part Number Refer to Drawing in:Postmodulekit914mm(36”)1,2 9120-TSM-PM-3317
Section 9.34—Post ModulesPostmodulekit1016mm(40”)1,2 9120-TSM-PM-3382Postmodulekit1220mm(48”)1,2 9120-TSM-PM-3325Postmodulekit1520mm(60”)1,2 9120-TSM-PM-3353Postmodulekit1828mm(72”)1,2 9120-TSM-PM-3322Notes:
1. May specify other rail lengths – cut charge will apply.2. The post module is available factory assembled - an assembly charge will apply.
2.1.2 Horizontal ModulesThe horizontal module mounts to the post module and can be adjusted vertically or horizontally using the rail gussets to accommodate customer tooling. The rail is an aluminum extrusion and comes in standard lengths. Multiple Tool plate assemblies can be added to the rail depending on the tool spacing requirements.
Item Part Number Refer to Drawing in:Horizontalmodule300mm(12”)1 9120-TSM-HM-3362
Section 9.39—Medium Tool Stand General Overview
Horizontalmodule457mm(18”)1 9120-TSM-HM-3323Horizontalmodule612mm(24”)1 9120-TSM-HM-1020Horizontalmodule914mm(36”)1 9120-TSM-HM-3317Horizontalmodule1220mm(48”)1 9120-TSM-HM-3325Horizontalmodule1520mm(60”)1 9120-TSM-HM-3353Notes:
1. May specify other rail lengths – cut charge will apply.
2.1.3 Horizontal ExtensionsThe horizontal extension is used when your tooling requires extra clearance from the rail or other tooling.The horizontal extension mounts to the post module.
Item Part Number Refer to Drawing in:
TSMHorizontalExtension,3.15” 9120-TSM-HE-3403
Section 9.39—Medium Tool Stand General OverviewTSMHorizontalExtension,6” 9120-TSM-HE-3320
TSMHorizontalExtension,10” 9120-TSM-HE-3321
2.1.4 TSM Adapter ModuleThe adapter module mounts to the horizontal extension. The adapter module is required for mounting module to be mounted or to the end of a horizontal extension.
Item Part Number Refer to Drawing in:TSM Adapter Module - Mounting Module to TSM HE1
9120-TSM-AM-9982 Section 9.33—Tool Hanger Module 5497
Notes: 1. Adapts to the TSM horizontal extension
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 12
2.1.5 Pin and Bushing Mounting ModulePin and bushing modules include two vertical alignment pins and one vertical bushing. The module includes mounting fasteners, and is designed to mount to a post module, horizontal module, or horizontal extension. The pin and bushing modules can be supplied as a stand alone unit and can be integrated with customer specific fixtures. The module provides mounting features for the sensor modules.
Item Part Number Refer to Drawing in:Pin and Bushing Mounting module, Rigid.1, 2 9120-TSM-MMB-8432 Section 9.1—Pin and Bushing Mounting
ModuleNotes:
1. Used with Tooling Interface Plates: 9120-TSM-HBQ-8439, 9120-TSM-VBB-8441, 9120-TSM-VBQ-8442.
2. Used with sensor modules: 9120-TSM-SMA-8437 and 9120-TSM-SMA-8439.
2.1.6 Tooling Interface PlatesThere are two types of interface plates, tooling interface plates and vertical tooling interface plates. The tooling interface plate attaches horizontally to the Tool Changer and the customer tooling. The vertical tooling plate attaches to the customer tooling and the Tool Changer is attached to the customer tooling either directly or using an interface plate. Both types of interface plates have two bushings and one alignment pin to position the tooling interface plate to the pin and bushing mounting module.Item Part Number Refer to Drawing in:
TSMToolingInterfacePlateforQC-50-Blank.1 9120-TSM-HBQ-9566Section 9.4—Pin and
Bushing QC-50 Tooling Plate
TSMToolingInterfacePlateforQC-76-Blank1 9120-TSM-HBQ-9224Section 9.5—Pin and
Bushing QC-76 Tooling Plate
TSMToolingInterfacePlateforQC-110-Blank1 9120-TSM-HBQ-8439Section 9.6—Pin and
Bushing QC-110 Tooling Plate
TSMToolingInterfacePlate-Blank1 9120-TSM-HBB-9223Section 9.7—Pin and
Bushing Horizontal Blank Tooling Plate
Vertical Tooling Interface Plate
TSMToolingInterfacePlate-Blank1 9120-TSM-VBB-8441Section 9.8—Pin and
Bushing Vertical Blank Tooling Plate
TSM Tooling Interface Plate - J16 Pattern 1 9120-TSM-VBQ-8442 Section 9.9—Pin and Bushing J16 Tooling Plate
Notes: 1. Used with mounting modules: 9120-TSM-MMB-8432.
2.1.7 RetrofitLockingAssemblyThe retrofit locking assembly includes a replacement alignment pin and a replacement bushing block with air cylinder for 9120-TSM-MMB-8432. For installation instructions refer to Section 9.10—TSM Pin & Bushing Mounting Module - Rigid - Locking.
Item Part Number Refer to Drawing in:
PinandBushingRetrofitLockingAssembly 9005-20-8444 Section 9.33—Pin and Bushing Retrofit
Locking Assembly
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 13
2.1.8 Pin and Bushing Locking Mounting ModulePin and bushing locking modules include two vertical alignment pins and one vertical bushing with an air cylinder. The module includes mounting fasteners, and is designed to mount to a post module, horizontal module, or horizontal extension. The pin and bushing locking modules can be supplied as a stand alone unit and can be integrated with customer specific fixtures. The module includes two sensors on the air cylinder.
Item Part Number Refer to Drawing in:PinandBushingLockingMountingmodule, Rigid.1 9120-TSM-MMBL-8432 Section 9.10—TSM Pin & Bushing Mounting
Module - Rigid - LockingNotes:
1. UsedwithToolingInterfacePlates:9120-TSM-HBBL-9223,9120-TSM-HBQL-10189,9120-TSM-VBBL-8441
2.1.9 Tooling Interface Plates LockingThere are two types of interface plates, tooling interface plates and vertical tooling interface plates. The tooling interface plate attaches horizontally to the Tool Changer and the customer tooling. The vertical tooling plate attaches to the customer tooling and the Tool Changer is attached to the customer tooling either directly or using an interface plate. Both types of interface plates have two bushings and one alignment pin to position the tooling interface plate to the pin and bushing mounting module. The tooling interface plates can be integrated with customer specific features, including a locking mechanism that secures tools in the tool stand, preventing unintional tool drops, wear, and potential damage.
Item Part Number Refer to Drawing in:
TSMToolingInterfacePlate-Blank-Locking1 9120-TSM-HBBL-9223Section 9.10—TSM Pin & Bushing Mounting Module
- Rigid - Locking
TSMToolingInterfacePlateforQC40-Locking-MA03 1 9120-TSM-HBQL-10189
Section 9.13—Tooling Interface Plate for QC 40-
Blank- MA03 (Locking)Vertical Tooling Interface Plate
TSMToolingInterfacePlate-Blank-Locking1 9120-TSM-VBBL-8441Section 9.12—Horizontal Tooling Interface Plate-
Blank (Locking) Notes:
1. Usedwithmountingmodules:9120-TSM-MMBL-8432
2.1.10 Proximity Sensor ModulesThe proximity sensor mounts directly to the mounting module. The proximity sensor provides a signal indicating the Tool is located in the tool stand.Item Part Number
TSM Sensor module, NPN, 8 mm Barrel 1 9120-TSM-SMA-8437
TSM Sensor module, PNP, 8 mm Barrel 1 9120-TSM-SMA-8439
Photoelectric Sensor Kit 1 9005-20-2152
Notes: 1. Used with mounting module: 9120-TSM-MMB-8432.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 14
2.2 TSM System with V-Block Style MountingThe system is compatible with QC-20 through QC-110 Tool Changers. The tool stand can be equipped with vertical mounting modules, horizontal modules, or with use of an adapter module to a horizontal extension and can be positioned anywhere along the rail. This system combines the ease of the V-block mounting module with adjustable tool spacing to accommodate customer tooling. There is an optional sensor holder that can attach to the mounting module. Options are limited to the lengths of horizontal modules to accommodate multiple tool mounts depending on the size of the tooling. Contact ATI for more information.
Figure 2.2—TSM System with V-Block Horizontal Mounting
Mounting Module
Tooling Interface Plate
Horizontal Module
Post Module
Horizontal Extension
Adapter Module
Figure 2.3— TSM System with V-Block Vertical Mounting
Vertical ToolingInterface Plate
Vertical MountingModule
Post Module
Horizontal Extension
AdapterModule
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 15
2.2.1 Post Module KitsThe post module kit is a common component to all TSM systems. The post module kit is available in different post heights and combines the base, rail, and gusset assemblies into a group of components.
Item Part Number Refer to Drawing in:Postmodulekit914mm(36”)1,2 9120-TSM-PM-3317
Section 9.34—Post ModulesPostmodulekit1016mm(40”)1,2 9120-TSM-PM-3382Postmodulekit1220mm(48”)1,2 9120-TSM-PM-3325Postmodulekit1520mm(60”)1,2 9120-TSM-PM-3353Postmodulekit1828mm(72”)1,2 9120-TSM-PM-3322Notes:
1. May specify other rail lengths – cut charge will apply.2. The post module is available factory assembled - an assembly charge will apply.
2.2.2 Horizontal ModulesThe horizontal module mounts to the post module and can be adjusted vertically or horizontally using the rail gussets to accommodate customer tooling. The rail is an aluminum extrusion and comes in standard lengths. Multiple Tool plate assemblies can be added to the rail depending on the tool spacing requirements.
Item Part Number Refer to Drawing in:Horizontalmodule300mm(12”)1 9120-TSM-HM-3362
Section 9.39—Medium Tool Stand General Overview
Horizontalmodule457mm(18”)1 9120-TSM-HM-3323Horizontalmodule612mm(24”)1 9120-TSM-HM-1020Horizontalmodule914mm(36”)1 9120-TSM-HM-3317Horizontalmodule1220mm(48”)1 9120-TSM-HM-3325Horizontalmodule1520mm(60”)1 9120-TSM-HM-3353Notes:
1. May specify other rail lengths – cut charge will apply.
2.2.3 Horizontal ExtensionsThe horizontal extension is used when your tooling requires extra clearance from the rail or other tooling.
Item Part Number Refer to Drawing in:
TSMHorizontalExtension,3.15” 9120-TSM-HE-3403
Section 9.39—Medium Tool Stand General OverviewTSMHorizontalExtension,6” 9120-TSM-HE-3320
TSMHorizontalExtension,10” 9120-TSM-HE-3321
2.2.4 TSM Adapter ModuleThe adapter module mounts to the horizontal extension. The adapter module is required for mounting module to be mounted or to the end of a horizontal extension.
Item Part Number Refer to Drawing in:TSM Adapter Module - Mounting Module to TSM HE1
9120-TSM-AM-9982 Section 9.35—TSM Rail Adapter Module - V-Block Style
Notes: 1. Adapts to the TSM horizontal extension
2.2.5 Mounting ModulesThe mounting module includes three pin receivers. The assembly includes mounting fasteners, and
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 16
is designed to mount to the horizontal module or with use of an adapter module to the post module or end of a horizontal extension. The mounting modules can be positioned anywher e along the rail to accommodate customer tooling. A mounting module is required for each tool position. The mounting module provides mounting holes for an optional sensor holder (see Section 2.2.9—Sensor Holders).
Item Part Number Refer to Drawing in: QC-ModelsMounting module 1,3 9120-TSM-MMV-3597 Section 9.16—Mounting Module 3597 QC-40 ~ QC-76Mounting module 2,4 9120-TSM-MMV-4018 Section 9.17—Mounting Module 4018 QC-100 ~ QC-110Notes:
1. Uses Sensor Holder 9120-TSM-SM-42052. Uses Sensor Holder 9120-TSM-SM-42063. Used with Tooling Interface Plates 9120-TSM-HVQ-XXXX except 9120-TSM-HVQ-4059.4. Used with Tooling Interface Plates 9120-TSM-HVQ-4059 and 9120-TSM-HVB-7961.
2.2.6 Tooling Interface PlatesThe tooling interface plate provides an interface from the customer tooling and Tool Changer to the tool stand. The tooling interface plate attaches to the Tool Changer and provides mounting for the customer tooling. The tooling interface plate uses three tooling pins to position the tooling interface plate to the mounting module. Tooling interface plates listed in table below require machining mounting pattern for customer tooling. Custom machined tooling interface plates are available, contact ATI for more information.
Item Part Number Refer to Drawing in: QC-Models
Tooling Interface Plate 2 9120-TSM-HVQ-4055 Section 9.18—QC-40 Tooling Interface Plate QC-40
Tooling Interface Plate 1, 2 9120-TSM-HVQ-4627 Section 9.18—QC-40 Tooling Interface Plate QC-40 Euro
Tooling Interface Plate 2 9120-TSM-HVQ-4056 Section 9.19—QC-41 Tooling Interface Plate QC-41
Tooling Interface Plate 2 9120-TSM-HVQ-4057 Section 9.20—QC-60 Tooling Interface Plate QC-60
Tooling Interface Plate 2 9120-TSM-HVQ-6660 Section 9.21—QC-62 Tooling Interface Plate QC-62
Tooling Interface Plate 2 9120-TSM-HVQ-4058 Section 9.22—QC-71 Tooling Interface Plate QC-71
Tooling Interface Plate 2 9120-TSM-HVQ-7290 Section 9.23—QC-76 Tooling Interface Plate QC-76
Tooling Interface Plate 3 9120-TSM-HVQ-4059 Section 9.24—QC-100 Tooling Interface Plate QC-100
Tooling Interface Plate 3, 4 9120-TSM-HVB-7961 Section 9.25—Blank Tooling Interface Plate QCBlank
Notes: 1. Euro Tool Changer Only.2. Used with mounting module 9120-TSM-MMV-3597.3. Used with mounting module 9120-TSM-MMV-4018.4. Blank-NoQCbossorQCmountingpattern.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 17
2.2.7 Vertical Mounting ModuleThe vertical mounting module includes three pin receivers. The mounting module includes mounting fasteners, and is designed to mount to the horizontal module, horizontal extension, or directly to the post module. The mounting module can be positioned anywher e along the rail to accommodate customer tooling. A mounting module is required for each tool position. The mounting module provides mounting holes for an optional sensor holder (see Section 2.2.9—Sensor Holders).
Item Part Number Refer to Drawing in: QC-Models
Vertical Mounting module2,3 9120-TSM-MMV-4068 Section 9.26—Vertical Mounting Module 4068 QC-40 ~ QC-76
Vertical Mounting module1,4 9120-TSM-MMV-4070 Section 9.27—Vertical Mounting Module 4070
QC-100 ~ QC-110
Notes: 1. Uses Sensor Holder 9120-TSM-SM-42052. Uses Sensor Holder 9120-TSM-SM-42063. Used with Vertical Tooling Interface Plates 9120-TSM-VVB-40694. Used with Vertical Tooling Interface Plates 9120-TSM-VVB-4071
2.2.8 Vertical Tooling Interface PlateThe vertical tooling interface plate provides an interface from the tool and Tool Changer to the TSM system. The tooling interface plate attaches to a flat on the customer tooling or Tool Changer. The tooling interface plate uses the (3) tooling pins to position the tooling interface plate with the mounting module.
Item Part Number Refer to Drawing in: QC-ModelsVertical Tooling Interface Plate-Blank1 9120-TSM-VVB-4069 Section 9.29—Vertical Tooling
Interface Plate - Blank (Large) QC-40 ~ QC-76
Vertical Tooling Interface Plate-Blank(Large)2 9120-TSM-VVB-4071 Section 9.29—Vertical Tooling
Interface Plate - Blank (Large) QC-100 ~ QC-110
Notes: 1. Used with mounting module 9120-TSM-MMV-40682. Used with mounting module 9120-TSM-MMV-4070
2.2.9 Sensor HoldersThe TSM sensor holders accommodate barrel-type proximity sensors with 18 x 1.0 thread. For operation, thread the sensor into the desired position to detect the surface of the TSM tooling interface plate as it is dropped off in the stand. ATI offers the following proximity sensor (see Section 2.2.10—Proximity Sensor).
Item Part Number Refer to Drawing in: QC-Models
Sensor Holder 9120-TSM-SM-4206
Section 9.36—Sensor Holders
QC-40 ~ QC-76
Sensor Holder 9120-TSM-SM-4205 QC-100 ~ QC-110
2.2.10 Proximity SensorThe proximity sensor screws directly into the sensor holder. The proximity sensor provides a signal indicating the Tool is located in the tool stand.
Item Part Number Refer to Drawing in: QC-Models
PNP 3-Wire DC Sensor 8590-9909999-45 Section 9.36—Sensor Holders QC-40 ~ QC-110
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 18
2.3 TSM System with Tool Hanger Mounting ModuleThe tool hanger mounting module is compatible with QC-20 through QC-71 Tool Changers and includes a rigid block that interfaces with the tool hanger. The mount assembly includes the mounting fasteners, and is designed to mount to extruded rail components and the flats on the Tool Changer. The assembly can be mounted to any other surface that has the corresponding mounting features.
Figure 2.4—Tool Hanger Mounting
Tool PlateTool Hanger
Tool Hanger Mounting Module
Sensor
HorizontalModule
PostModule
2.3.1 Post Module KitsThe post module kit is a common component to all TSM systems. The post module kit is available in different post heights and combines the base, rail, and gusset assemblies into a group of components.
Item Part Number Refer to Drawing in:Postmodulekit914mm(36”)1,2 9120-TSM-PM-3317
Section 9.34—Post ModulesPostmodulekit1016mm(40”)1,2 9120-TSM-PM-3382Postmodulekit1220mm(48”)1,2 9120-TSM-PM-3325Postmodulekit1520mm(60”)1,2 9120-TSM-PM-3353Postmodulekit1828mm(72”)1,2 9120-TSM-PM-3322Notes:
1. May specify other rail lengths – cut charge will apply.2. The post module is available factory assembled - an assembly charge will apply.
2.3.2 Horizontal ModulesThe horizontal module mounts to the post module and can be adjusted vertically or horizontally using the rail gussets to accommodate customer tooling. The rail is an aluminum extrusion and comes in standard lengths. Multiple Tool plate assemblies can be added to the rail depending on the tool spacing requirements.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 19
Item Part Number Refer to Drawing in:Horizontalmodule300mm(12”)1 9120-TSM-HM-3362
Section 9.39—Medium Tool Stand General Overview
Horizontalmodule457mm(18”)1 9120-TSM-HM-3323Horizontalmodule612mm(24”)1 9120-TSM-HM-1020Horizontalmodule914mm(36”)1 9120-TSM-HM-3317Horizontalmodule1220mm(48”)1 9120-TSM-HM-3325Horizontalmodule1520mm(60”)1 9120-TSM-HM-3353Notes:
1. May specify other rail lengths – cut charge will apply.
2.3.3 Tool Hanger Mounting ModulesThe tool hanger mounting module includes a rigid block with locating pins.
Item Part Number Refer to Drawing in: QC-Models
Tool Hanger Mounting module 9120-TSM-MM-5496
Section 9.30—Tool Hanger Module 5496
Section 2.3—TSM System with Tool Hanger Mounting Module
QC-20 ~ QC-71
Note:
Used with 9120-TSM-TH-5891, 9120-TSM-TH-5923, and 9120-TSM-TH-5497
2.3.4 Tool HangersThe tool hanger provides an interface between your Tool Changer and mounting module. The tool hangers are sized and designed to correspond with the Tool Changer module flats. The tool hanger also includes (2) steel alignment features—a shoulder bolt that aligns with the mounting module groove and a locating pin to align with the corresponding slot in the mounting module.
Item Part Number Refer to Drawing in: QC-Models
Tool Hanger3 9120-TSM-TH-5891 Section 9.31—Tool Hanger Module 5891
Section 9.32—Tool Hanger Module 5923
Section 9.33—Tool Hanger Module 5497
Section 2.3—TSM System with Tool Hanger Mounting Module
QC-201, QC-211, QC-21E 1
Tool Hanger3 9120-TSM-TH-5923 QC-212, QC-21E2
Tool Hanger3 9120-TSM-TH-5497 QC-401, 2, QC-40Q1, 2, QC-411, QC-711, 2
Notes: 1. Mounts to Flat A.2. Mounts to Flat B3. Used with mounting module 9120-TSM-MM-5496
2.3.5 Proximity Sensor and Cables for Tool Hanger Mounting ModuleThe proximity sensor can be screwed into the tool hanger mounting module. The proximity sensor provides a signal indicating the Tool is located in the tool stand. Sensor cables are available in various lengths. This proximity sensor is not compatible with the V-block mounting module.
Proximity SensorItem Part Number QC-ModelsProximity Sensor PNP 3 wire DC 8590-9909999-34 QC-20 ~ QC-71
Sensor CablesItem Part Number QC-Models
2 meter female 8590-9909999-07 QC-20 ~ QC-71
5 meter female 8590-9909999-12 QC-20 ~ QC-71
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 20
2.4 Post Module ComponentsThe post module is a common component to all TSM systems. The post module is available in different post heights and combines the base, rail, and gusset assemblies into a group of components.
Figure 2.5—Post module Components
Rail Assembly
Gusset Assembly
Base Assembly
2.4.1 Base PlateThe base plate consists of a square aluminum machined plate. The base provides a secure foundation on which to build the TSM system.
Item Part Number Refer to Drawing in:
Base Plate 3700-20-3589 Section 9.34—Post Modules
2.4.2 Rail AssembliesThe rail assembly mounts to the base assembly. The standard rail is an aluminum extrusion and in a variety of lengths. Customers can request custom lengths when ordering.
Item Part Number Refer to Drawing in:PostRail914mm(36”) 3710-20-3435
Section 9.34—Post ModulesPostRail1016mm(40”) 3710-20-3382PostRail1220mm(48”) 3710-20-3318PostRail1520mm(60”) 3710-20-3334PostRail1828mm(72”) 3710-20-3322
*Note: The customer may specify other rail lengths – cut charge will apply.
2.4.3 Gusset AssemblyThe gusset assembly provides structural support at the base of the assembly. The gusset assembly mounts to the base assembly and includes mounting fasteners. Note: Tabs must be removed from the gusset to allow flush contact with the base assembly.
Item Part Number Refer to Drawing in:
Gusset 9120-TSS-GA-1030 Section 9.34—Post Modules
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 21
2.5 DeterminingTheToolStandConfigurationDetermining the components needed for a tool stand requires knowledge of the system being designed. When determining the tool stand components, you will need to consider the following information:• What model Tool Changer will be used and if utility modules will be required.
• Number of tools the stand must accommodate, total weight.
• Dimensions of the tooling that will be used, tooling weight.
• Size, reach and capabilities of the robot being used.
• Area available to accommodate the tool stand.
• Area between tool positions required for pneumatic fittings, hoses, electrical cabling and other utilities.
Figure 2.6—Tool Stand and Tool SpacingHorizontal Module length to accomodate
number of Tools and Tool Spacing.
Post Module height to accomodate Adapter Plate, Tooling, Pneumatic
Fittings, Pneumatic Hoses and Electrical Cabling.
Height of Tooling, Adapter Plate, Utility Fittings, Hoses, and CablingWill Be Needed to Determine the Post Module Height and Height
to set the Horizontal Module.
For Tool spacing the Width of the Tool Changer, Tooling interface Plate, Customer Tooling, Utilities, Pneumatic
Fittings, Pneumatic Hoses, Electrical Cabling must be considered to determine proper Tool spacing.
Post Module
Horizontal Module
Adapter Plate
Pneumatic Fittings
and Hoses
Customer Tooling
Tool Changer Model
Tooling Interface Plate
Figure 2.7—ToolStandConfigurations
Depth of the Tooling is limited by the Tooling Interface Plate
and the Monting Module. CustomTooling Inerface Plates are available,
contact ATI for information.Post Module
Horizontal Module
Adapter Plate
Pneumatic Fittings and Hoses
Customer Tooling
Tool Changer Tool Plate
Optional Utility ModulesTooling Interface Plate
Mounting Module
Customer Tooling
Adapter Plate
Note: Mounting Module mounted to Post Module
Note: Mounting Module mounted to Horizontal Module
Mounting Module
Tooling Interface Plate
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 22
2.5.1 ConfiguringaTSMSystemwithHorizontalMountingA TSM system with horizontal mounting provides variable spacing tool positions and tool sensing options for Tool Changer models QC-40 through QC-110. The mounting module can mount to the post module using an adapter module for up to two tool positions, or mount to an optional horizontal module to accommodate multiple tool positions. Refer to the Drawing in Section 9 for detailed information.
Figure 2.8—HorizontalMountingSystemConfigurations
2.5.2 ConfiguringaTSMSystemwithPinandBushingMountingA TSM system with pin and bushing mounting provides variable spacing tool positions and tool sensing options for Tool Changer models. The mounting module can mount to the post module using an adapter module for up to two tool positions, or mount to an optional horizontal module to accommodate multiple tool positions. Refer to the Drawing in Section 9 for detailed information.
Figure 2.9—PinandBushingMountingSystemConfigurations
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 23
2.5.3 ConfiguringaTSMSystemwithVerticalMountingA TSM system with vertical mounting can mount directly to the post module for up to two tool positions or mount to an optional horizontal module to accommodate multiple tool positions. Refer to Drawing in Section 9 for detailed information.
Figure 2.10—VerticalMountingConfigurations
2.5.4 ConfiguringaTSMSystemwithToolHangerMountingTool hanger mounting provides multiple tool positions for Tool Changer models QC-20 through QC-71. The mounting module is mounted to the horizontal module or vertical post. Optional proximity sensors can be added for Tool presence sensing.
Figure 2.11—ToolHangerConfigurations
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 24
3. InstallationThe tool stand is shipped unassembled. The customer must perform the final assembly and determine the proper location for the tool stand.
CAUTION: Allpneumaticfittingsandtubingmustbecapableofwithstandingtherepetitivemotions of the application without failing. The routing of electrical and pneumatic lines must minimizethepossibilityofstresspullout,kinking,rupture,etc.Failureofsomecriticalelectricaland/or pneumatic lines to function properly may result in injury to personnel and damage to equipment.
3.1 Installing Base, Rail, and Gusset assembliesTools required: 6 mm and 10 mm Allen wrench, 13 mm socket wrench, screw driver, torque wrench
1. Determine the proper location and configuration of your tool stand. Assemble the base, rail and gusset assemblies prior to anchoring the TSM base.
2. Assemble the gussets to the rail by inserting the T-bolts into the T-slots in the rail and turning the T-bolts 90°.
3. Insert a screw driver into the slot under the tab. 4. Pry up on the tab to break it off. 5. Remove any burrs that may not allow flush contact to the base assembly.
Figure 3.1—Removing Tabs on Gussets Using Screw Driver
Remove The Tabs On The Gusset That Will Contact The Base Assembly
Remove The Tabs On TheGusset That Will Contact
The Base Assembly
Pry Up On The Tab to Break It Off
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 25
6. Assemble the rail to the base with the (4) M12 socket head cap screws using a 10 mm Allen wrench, refer to Section 9—Drawings for specific details on torque and thread tool hanger requirements.
7. Insert the M8 socket head cap screws through the base and gussets. Secure with the M8 flat washer and nut. Using a 6 mm Allen wrench, tighten the nuts on the T-bolts holding the gussets to the rail using a 13 mm soxket wrench. Refer to Section 9—Drawings for specific details on torque and thread requirements.
Figure 3.2—Installing Base, Rail, and Gusset assemblies
Rail Assembly
(4) Gusset Assembly
Base Assembly
(16) M8 Nut(16) M8 Flat Washer
(16) T-BoltInsert the T-bolts into the
T-Slots in the Rail Assembly andturn the T-bolts 90°
(8) T-Slots
(16) M8 Bolt
(4) M12 Bolt
8. Anchor the TSM base to a smooth flat surface using the (4) 13 mm through holes provided (fasteners not included).
9. To continue installation, refer to the following sections:• Section 3.2—Installing Pin and Bushing or Horizontal V-Block Mounting Module to Tool Stand• Section 3.3—Installing Vertical V-Block Mounting Module to Tool Stand • Section 3.4—Installing Tool Hanger Mounting Module to Tool Stand• Section 3.5—Installing Horizontal Extension to Tool Stand
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 26
3.2 Installing Pin and Bushing or Horizontal V-Block Mounting Module to Tool StandTools required: 6 mm Allen wrench, 13 mm socket wrench, torque wrench
1. Refer to the drawing for the model being assembled in Section 9—Drawings. The drawings provide torque, thread, and other specific requirements.
2. Assemble the horizontal module to the post module by inserting the T-bolts into the T-slots in the rail. Turn the T-bolts 90° and torque.
3. Adjust the height of the horizontal module to accommodate the tooling and tighten the nuts on the T-bolts to secure the vertical position of the rail, further adjustments to horizontal module may be required using a 13 mm socket wrench.
4. Remove the horizontal module end cap and assemble the mounting module to the horizontal module by sliding the T-nuts into the T-slots on the horizontal module.
5. Install additional mounting modules if needed.6. Position the horizontal module and the mounting modules to accommodate the tool spacing desired and
tighten the T-bolts for the horizontal position of the rail. Tighten the M8 socket head cap screws to secure the mounting modules using a 6 mm Allen wrench.
7. Place the end cap on the horizontal module.
Figure 3.3—Installing Tooling Interface Plates (V-Block Shown)
(6) Mounting Fastener
End Cap(4) T-nut
(4) T-nutMounting Module
Mounting Module
Tooling Interface Plate
Tooling Interface Plate
Tool Changer Tool Side
End Cap
(4) T-Bolt
Horizontal Module
Post Module
(6) Mounting Fastener
T-slots
T-slots
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 27
Figure 3.4—Installing Tooling Interface Plates (Pin and Bushing Shown)
T-slotsT-slots
T-slotsT-slotsHorizontal Module
(4) T-Bolt
(4) T-nut
Mounting ModuleEnd Cap
(6) Mounting Fastener
Horizontal Tooling Interface Plate
Vertical Tooling Interface Plate
Vertical ToolingInterfacePlate
End Cap
Tool Changer Tool Side
Tool Changer Tool Side
Post Module
Mounting Module
Mounting Module
(4) T-nut
(4) T-nut
8. If equipped, install the optional proximity sensor to the mounting module. Refer to Section 3.6—Proximity Sensor Module Installation for Pin and Bushing TSM Systems and Section 3.7—Proximity Sensor Installation for V-Block TSM Systems (Sensor Holder 9120-TSM-SM-4205).
9. If the tooling interface plate is a blank plate, it will need to be machined with the mounting pattern for the Tool Changer and/or customer tooling desired. Refer to Section 9—Drawings for the specific Tool Changer being used for the mounting pattern required.
10. Assemble the customer tooling and Tool Changer to the tooling interface plate assembly. Then place on the mounting module. Refer to your Tool Changer manual for proper installation of the tooling interface plate.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 28
3.3 Installing Vertical V-Block Mounting Module to Tool StandTools required: 6 mm Allen wrench, torque wrench
1. Refer to the drawing for the model being assembled in Section 9—Drawings. The drawings provide torque, thread, and other specific requirements.
2. Remove the post module end cap. Refer to Figure 3.5.3. Assemble the mounting module to the post module by sliding the T-nuts into the T-slots in the rail. 4. Adjust the height of the mounting module or horizontal module to accommodate the tooling for the
application and tighten the M8 socket head cap screws using a 6 mm Allen wrench. 5. Place the end cap on the post module.6. If the tooling interface plate is a blank plate it will need to be machined with the mounting pattern for
the Tool Changer and/or customer tooling desired. Refer to Section 9—Drawings for the specific Tool Changer being used for the mounting pattern required.
7. Assemble the customer tooling and/or Tool Changer to the tooling interface plate. Then place on the mounting module.
Figure 3.5—Installing Vertical Tooling Interface Plates
End Cap
Vertical ToolingInterface Plate
Vertical Mounting Module
Vertical Mounting Module
T-slots(4) T-nut
Post Module
Vertical ToolingInterface Plate
8. If equipped, install the optional sensor holder and proximity sensor. Refer to Section 3.7—Proximity Sensor Installation for V-Block TSM Systems (Sensor Holder 9120-TSM-SM-4205).
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 29
3.4 Installing Tool Hanger Mounting Module to Tool StandTools required: 6 mm Allen wrench, 13 mm socket wrench, torque wrench
1. Refer to the drawing for the model being assembled in Section 9—Drawings. The drawings provide torque, thread, and other specific requirements.
2. Assemble the horizontal module to the post module by inserting the T-bolts into the T-slots in the rail. Turn the T-bolts 90° and torque.
3. Adjust the height of the horizontal module to accommodate the tooling for the application and tighten the nuts on the T-bolts to secure the vertical position of the rail using a 13 mm socket wrench. Further adjustments to horizontal module may be required.
4. Remove the horizontal module end cap and assemble the mounting module to the horizontal module by sliding the T-nuts into the T-slots on the horizontal module.
5. Adjust the height of the mounting module to accommodate the tooling for the application and tighten the M8 socket head cap screws.
6. Place the end cap on the horizontal module.7. Assemble the customer tooling and Tool Changer to the tool hanger. Then place on the mounting
module.
Figure 3.6—Installing Tool Hanger Mounting Modules
Post Module
Horizontal Module
End Cap
End Cap
End Cap
(4) T-bolt
(2) T-nut
(2) T-nut
T-slots
Mounting Module
Mounting Module
(4) Mounting Fastener
(4) Mounting Fastener
Tool Hanger
Tool Hanger
Tool Changer Tool Side(QC-71 shown)
Tool Changer Tool Side(QC-71 shown)
T-slots
8. If equipped, install the optional proximity sensor. Refer to Section 3.9—Proximity Sensor installation for TSM Tool Hanger
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 30
3.5 Installing Horizontal Extension to Tool StandTools required: 6 mm and 10 mm Allen wrench, 13 mm socket wrench, torque wrench
1. Refer to the drawing for the model being assembled in Section 9—Drawings. The drawings provide torque, thread, and other specific requirements.
2. Assemble the horizontal extension to the rail by inserting the T-bolts into the T-slots in the rail. Turn the T-bolts 90° and finger tighten.
3. Adjust the height of the horizontal extension to accommodate the tooling for the application and tighten the nuts to proper torque on the T-bolts to secure the vertical position of the extension using a 13 mm socket wrench.
4. Assemble the adapter module or vertical mounting plate to the end of the horizontal extension with the M12 mounting fasteners using a 10 mm Allen wrench.
Figure 3.7—Installing Horizontal Extension
(4) T-bolt
Vertical Mounting Plate
Horizontal ExtensionHorizontal Extension
Adapter Plate
(4) M12 Mounting Fastener
(4) M12 Mounting Fastener
Post Module
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 31
3.6 Proximity Sensor Module Installation for Pin and Bushing TSM SystemsTools required: 2.5 mm Allen wrench, torque wrenchSupplies required: Loctite 222®
1. Apply Loctite 222 or similar to the (2) M3 socket head cap screws used to mount the proximity sensor.2. Attach the proximity sensor module to the mounting module with the (2) M3 socket head cap screws.
Tighten to contact using a 2.5 mm Allen wrench. Note: The sensor module can be attached to either side of the mounting module.
3. Attach the sensor cable or wires to the proximity sensor.
Figure 3.8—Proximity Sensor Position for V-Block TSM
(2) M3 Socket Head Cap Screw
(2) M3 Socket Head Cap Screw
Barrel Type Sensor
Photoelectric Type Sensor
MountingModule
Sensor Cable P-Clip
Sensor Cable P-Clip
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 32
3.7 Proximity Sensor Installation for V-Block TSM Systems (Sensor Holder 9120-TSM-SM-4205)Tools required: 5 mm Allen wrench, 24 mm wrench, torque wrench
1. Remove the (2) M6 socket head cap screws using a 5 mm Allen wrench from the inside of each of the top pin receivers from the mounting module.
2. Apply Loctite 222 or similar to the (4) M6 socket head cap screws used to mount the proximity sensor holder.
3. Attach the proximity sensor holder to the mounting module with the (4) M6 socket head cap screws using a 5 mm Allen wrench and spacers if required. Tighten to 6 in-lbs (0.68 Nm).
4. Screw the proximity sensor into the holder and initially position so the face of the sensor is flush with the plate being re-installed as shown in Figure 3.9. Do not extend the sensor beyond the face of the plate toward the tooling plate.
5. Snug the jam nuts finger tight, and connect the sensor cable.6. Adjust sensing distance as needed and tighten the jam nuts using a 24 mm wrench.
Figure 3.9—Proximity Sensor Position for V-Block TSM (Sensor Holder 9120-TSM-SM-4205)
Plate BeingRe-installed
(4) M6 Socket Head Cap ScrewBeing Removed
(4) Spacer
Sensor Holder(9120-TSM-SM-4205 Shown)
Sensor
(4) M6 Socket Head Cap Screw
Mounting Module(9120-TSM-MMV-4070 Shown)
(2) Jam Nut
Initially position thesensor face flushwith this plate. Do notextend the sensorbeyond this plate towardthe tooling plate.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 33
3.8 Proximity Sensor Installation for V-Block TSM Systems (Sensor Holder 9120-TSM-SM-4206)Tools required: 2.5 mm and 5 mm Allen wrench, torque wrenchSupplies required: Loctite 222
1. Remove the (2) M6 socket head cap screws using a 5 mm Allen wrench from the inside of each of the top pin receivers on the mounting module.
2. Apply Loctite 222 or similar to the (4) M6 socket head cap screws using a 5 mm Allen wrench to mount the proximity sensor holder.
3. Attach the proximity sensor holder to the mounting module with the (4) M6 socket head cap screws and spacers if required. Tighten to 6 in-lbs (0.68 Nm) using a 5 mm Allen wrench.
4. Screw the proximity sensor into the holder and initially position so the face of the sensor is .09˝ from the side of the tooling interface plate as shown in Figure 3.10.
5. Snug the M3 set screw using 2.5 mm Allen wrench and connect the sensor cable.6. Adjust sensing distance as needed.
Figure 3.10—Proximity Sensor Position for V-Block TSM (Sensor Holder 9120-TSM-SM-4206)
(2) M6 Fastener Being Removed
(2) M6 Fastener Being Removed
Mounting Module(9120-TSM-MMV-3597 Shown)
Sensor(4) M6 Socket Head Cap Screw
Sensor Holder(9120-TSM-SM-4206 Shown)
M3 SetScrew
Adjust the sensor to an initial position .09" from the face of the sensor to the side of the Tooling Interface Plate.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 34
3.9 Proximity Sensor installation for TSM Tool HangerTools required: 13 mm socket wrench, torque wrench
1. Attach the proximity sensor to the mounting module by screwing the sensor into the bottom of the mounting module. Tighten to 6 in-lbs (0.68 Nm).
2. Position the sensor so the sensor face is flush with the surface of the mounting module. 3. Adjust sensor position as needed.4. Tighten the jam nut on the sensor against the mounting module using a 13 mm wrench.5. Attach the sensor cable to the proximity sensor.
Figure 3.11—Proximity Sensor Position for TSM Tool Hanger
Mounting Module
Proximity Sensor
Jam Nut
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 35
4. OperationThe ATI TSM system is intended for use with No-touch Tool Changers only, such as ATI changers QC-40 through QC-110.
CAUTION: Damage will occur if contact is made between the TSM pin and bushing tooling Plate and the mounting module prior to tool drop-off
4.1 TSM System with Pin and Bushing Style Mounting OperationFor proper tool drop-off, ATI recommends 3 mm (0.118”) maximum clearance between TSM pin and bushing mounting module contact surfaces and the TSM tooling interface plate contact surface. See Section 9.28—Vertical Tooling Interface Plate - Blank for reference.
Figure 4.1—Maximum Clearance for Proper Tool Drop-off for Pin and Bushing Style Mounting
3mm (.118”) Gap Max.Prior to Tool Drop Off
Tooling Interface Plate
Pin and Bushing Module
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 36
4.2 TSM V-Block Systems OperationFor proper tool drop-off, ATI recommends 6.35 mm (.25”) maximum distance from the center point of the tooling pin on the interface plate and the center point of the pin slot on the pin receiver. A reference dimension is shown for ease of measuring. See Figure 4.3 for reference.
Figure 4.2—Proper Clearance for V-Block Tool Drop-off
(.25”)6.35 mm
Mounting ModuleTooling Pin
Ref. 0.519”13.18mm
V-BlockMounting Module
Tooling Interface Plate
Ref. 0.244”6.20mm
V-BlockMounting Module
Vertical ToolingInterface Plate
4.3 TSM Tool Hanger System OperationFor proper tool drop-off, ATI recommends 1 mm maximum clearance between TSM tool hanger mounting module contact surfaces and the tool hanger contact surfaces. A reference dimension is shown for ease of measuring. See Figure 4.3 for reference.
Figure 4.3—Tool Hanger Systems Maximum Clearance for Proper Tool Drop-off
(.039”)1mm
Mounting Module Tool Hanger Pin
Tool Hanger
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 37
5. MaintenanceWARNING: Do not perform maintenance or repair(s) on the Tool Changer or modules unless the Tool is safely supported or placed in the tool stand, all energized circuits (e.g. electrical, air, water, etc.) are turned off, pressurized connections are purged and power is discharged from circuits in accordance with the customer’s safety practices and policies. Injury or equipment damage can occur with the Tool not placed and energized circuits on. Place the Tool in the tool stand, turn off and discharge all energized circuits, purge all pressurized connections, and verify all circuits are de-energized before performing maintenance or repair(s) on the Tool Changer or modules.
It is recommended that the following areas should be checked at least once every 100,000 cycles. Earlier intervention may be necessary if a problem is identified prior to the scheduled maintenance checks.
5.1 All TSM Systems• Verify that the horizontal module or extension has not loosened. Tighten if required. Refer to
Section 3.2—Installing Pin and Bushing or Horizontal V-Block Mounting Module to Tool Stand and Section 3.5—Installing Horizontal Extension to Tool Stand.
• Verify that the mounting module has not loosened. Tighten if required. Refer to Section 3.2—Installing Pin and Bushing or Horizontal V-Block Mounting Module to Tool Stand, Section 3.4—Installing Tool Hanger Mounting Module to Tool Stand, and Section 3.3—Installing Vertical V-Block Mounting Module to Tool Stand
• Verify that the gussets have not loosened. Tighten if required. Section 3.1—Installing Base, Rail, and Gusset assemblies
• Verify that the base has not loosened. Tighten if required. Section 3.1—Installing Base, Rail, and Gusset assemblies
• Verify that the proximity sensor and holder have not loosened. Tighten if required. Section 3.7—Proximity Sensor Installation for V-Block TSM Systems (Sensor Holder 9120-TSM-SM-4205), and Section 3.9—Proximity Sensor installation for TSM Tool Hanger
• Inspect sensor cables and all utility lines for wear
• Inspect and wipe clean all sensor faces to ensure proper function
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 38
5.2 Pin and Bushing TSM SystemsClean and lubricate pin and bushing module. Check the (3) alignment pins for looseness, wear, and damage. If loose apply Loctite and tighten, if worn or damaged, replace. Check the (3) alignment bushing for wear and damage. If worn or damaged, replace.
5.2.1 Clean, Lubricate, and Replace Alignment Pins and BushingsParts required: Refer to Section 9—Drawings.Supplies required: Clean rag, MobilGrease XHP222
1. Remove the Tool from the tool stand.2. Using a lint free rag, remove the debris from the alignment pins, alignment bushing, and top
surface of the mounting module. Also remove the debris form the (2) bushings and alignment pin in the tooling interface plate shown in Section Figure 5.1——Clean and Lubricate the Alignment Pins and Alignment Bushings.
Figure 5.1—Clean and Lubricate the Alignment Pins and Alignment Bushings
Alignment BushingsAlignment Bushings
Alignment Bushing
Alignment Pin
Alignment Pin
Alignment Pin
Top Surface of the Mounting Module
Apply MobilGrease XHP222Special grease to the AlignmentPins and the Alignment Bushings
3. Inspect the (3) alignment pins for looseness, wear, or damage. d. If worn or damaged remove, discard, and replace with new alignment pin. Apply Loctite 242 to
the threads of the new pin and thread into the mounting module. Tighten to 80 in-lbs (9.04 Nm).
e. If loose, remove and apply Loctite 242 to the threads. Thread into the mounting module. Refer to Section 9—Drawings for torque.
6. Inspect the (3) alignment bushings for wear or damage. If worn or damaged remove, discard, and replace with new alignment bushing. Press out old bushing using an arbor press, then press in new bushing.
7. Apply liberal amounts of MobilGrease® XHP222 Special grease to the alignment pins and the alignment bushing on the mounting module as shown in Section Figure 5.1——Clean and Lubricate the Alignment Pins and Alignment Bushings
8. Place the Tool in the tool stand.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 39
5.3 TSM V-Block Systems• Inspect the tooling pins and pin receivers for cracks and wear. Replace if necessary.
• Lubricate tooling pins and pin receivers, see Section Figure 5.2——Sensor Cleaning and Lubrication Locations (V-Block System) and Section 9—Drawings for details.
• Check the tooling pins for looseness. Refer to Section Figure 5.2——Sensor Cleaning and Lubrication Locations (V-Block System) and Section 9.16—Mounting Module 3597, Section 9.17—Mounting Module 4018, Section 9.26—Vertical Mounting Module 4068, Section 9.27—Vertical Mounting Module 4070 for torque
• Check to verify that the mounting module has not loosened. Tighten if required. Refer to Section 3.2—Installing Pin and Bushing or Horizontal V-Block Mounting Module to Tool Stand, Section 3.4—Installing Tool Hanger Mounting Module to Tool Stand, and Section 3.3—Installing Vertical V-Block Mounting Module to Tool Stand
Figure 5.2—Sensor Cleaning and Lubrication Locations (V-Block System)
Clean and Inspect Pins,and Apply New Lubricant
Clean and Inspect Pins,and Apply New Lubricant
Clean and Inspect Sensorand Surrounding Surfaces
Clean and Inspect Pin Receivers
Clean and Inspect Pin Receivers
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 40
5.4 TSM Tool Hanger Systems• Inspect the hanger pins and mounting module for cracks and wear. Replace, if necessary.
• Lubricate the mounting module pins, see Figure 5.3. • Check to verify that the mounting module has not loosened. Refer to Section 9.30—Tool Hanger
Module 5496, Section 2.3—TSM System with Tool Hanger Mounting Module.
• Section Figure 5.1——Clean and Lubricate the Alignment Pins and Alignment Bushings for torque.
Figure 5.3—Sensor Cleaning and Lubrication Locations (Tool Hanger System)
Clean and Inspect Sensorand Surrounding Surfaces
Clean and Inspect Pins,and Apply New Lubricant
Clean and Inspect Pins,and Apply New Lubricant
Clean and Inspect Pin
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 41
6. TroubleshootingRefer to the following table for troubleshooting information.
Table 6.1—TroubleshootingSymptom Possible Cause Correction
Tool drop-off location no longer repeatable
Tool alignment pin may be loose or missing.
Tighten or replace if necessary.
Tool position while in storage is no longer straight and parallel.
Tool alignment pin may be loose, worn, damaged, or missing.
Tighten or replace alignment pins if necessary. Refer to Section 5.2.1—Clean, Lubricate, and Replace Alignment Pins and Bushings.
Alignment bushing may be worn.
Inspect the alignment bushings for wear. Replace if necessary. Refer to Section 5.2.1—Clean, Lubricate, and Replace Alignment Pins and Bushings.
Proximity sensor fails
Debris build up on proximity sensor. Checkfordebrisbuildupandcleanifnecessary.
Proximity sensor loose or not positioned properly.
Verify that the correct distance between sensing face and target is set. Adjust if necessary. Refer to Section Figure 3.9——Proximity Sensor Position for V-Block TSM (Sensor Holder 9120-TSM-SM-4205), , and Section 4.1—TSM System with Pin and Bushing Style Mounting Operation.
Sensor cable brokenordamaged.
Inspect sensor cable for damage, test continuity, replace, if damaged.
Proximity sensor damaged or not functioning.
Inspect proximity sensor for damage, test sensor.
Tool/end effector malfunctioning
Utility lines and cables damaged.
Inspect utility lines and cables for wear. Inspect all connections for damage. Verify Tool Changer for proper function.
Tool Changer or utility modules not functioning properly.
Verify Tool Changer and utility modules for proper function. Refer to the Tool Changer and Module Installation and Operation manual for troubleshooting.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 42
7. Serviceable PartsThe following items are commonly used as spare parts for the TSM system.
Other components are available upon request.
Table 7.1—Serviceable Parts
Model Part Number Name Used For Torque Spec.
Common TSM Pin and Bushing System Components (Refer to Section 2.1—TSM System with Pin and Bushing Style Mounting
3700-20-8434
TSM Pin & Bushing, alignment pin, Dual Taper
All TSM pin and bushing mounting modules
80 in-lbs (9 Nm)
3700-20-8436 (Elongated)
3700-20-8435 (Round)
Drill Bushing, Flanged, 16 mm ID
All TSM pin and bushing mounting modules NA
CommonTSMV-BlockSystem Components (Refer to Section 2.2—TSM System with V-Block Style Mounting)
3700-20-3594 Tooling Pin - Short M10 Threaded Tooling Plates 180 in-lbs (20 Nm)
3700-20-4016 ToolingPin-Long M10 Threaded Tooling Plates 80 in-lbs (9 Nm)
3700-20-3590 Tooling Pin - Short M12 Threaded Tooling Plates 180 in-lbs (20 Nm)
3700-20-4017 ToolingPin-Long M12 Threaded Tooling Plates 80 in-lbs (9 Nm)
Tool Hanger TSM System Components (Refer to Section 2.3—TSM System with Tool Hanger Mounting Modulee)
8590-9909999-34 Proximity Sensor To detect Tool in Tool Stand NA
3690-62014001-11 Alignment Pin Used as alignment pin for Tooling Hanger module
52 in-lbs (5.8 Nm)
3500-2069080-11
SocketCapShoulder Screw, 10 mm x 80 mm, M8 Thread, Steel
Used as alignment pin for Tooling Hanger module
40 in-lbs (4.5 Nm)
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 43
7.1 Part Number Cross Reference7.1.1 TSM V-Block SystemsThe TSM tool stand part numbers and descriptions have been changed to provide a consistent numbering and naming scheme for all components of the tool stand system. The following tables provide a cross reference from the originally used part numbers to the current part numbers.
Original Part Number Current Part Number DescriptionSection 2.2.6—Vertical Tooling Interface Plate
9120-TSM-TP-4069 9120-TSM-VVB-6604 VerticalToolingInterfacePlate-Blank
9120-TSM-TP-6604 9120-TSM-VVC-6604 VerticalToolingInterfacePlatewith(4)1/4”CounterBores
9120-TSM-TP-4071 9120-TSM-VVB-4071 VerticalToolingInterfacePlate-Blank(Large)
Section 2.2.6—Tooling Interface Plates9120-TSM-TP-4055 9120-TSM-HVQ-4055 ToolingInterfacePlate-BlankQC-40
9120-TSM-TP-4627 9120-TSM-HVQ-4627 ToolingInterfacePlate-BlankQC-40Euro
9120-TSM-TP-4056 9120-TSM-HVQ-4056 ToolingInterfacePlate-BlankQC-41
9120-TSM-TP-4057 9120-TSM-HVQ-4057 ToolingInterfacePlate-BlankQC-60
9120-TSM-TP-6660 9120-TSM-HVQ-6660 ToolingInterfacePlate-BlankQC-62
9120-TSM-TP-4058 9120-TSM-HVQ-4058 ToolingInterfacePlate-BlankQC-71
9120-TSM-TP-7290 9120-TSM-HVQ-7290 ToolingInterfacePlate-BlankQC-76
9120-TSM-TP-4059 9120-TSM-HVQ-4059 ToolingInterfacePlate-BlankQC-100
9120-TSM-TP-7961 9120-TSM-HVB-7961 ToolingInterfacePlate-Blank
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 44
8. SpecificationsWeights shown in the following tables are prior to custom machining and additional tooling requirements.
8.1 Common TSM System ComponentsPart Description Material Weight-MassTSM Base T-6 Aluminum 2.4 lbs.TSM Sensor Holder Anodized T-6 .3 lbs.TSM Post Anodized T-6 Extruded Aluminum Varies.TSM Gusset Cast Aluminum 6.8 lbs.
8.2 TSM Pin and Bushing System ComponentsPart Description Material Weight-MassTSM Pin and Bushing Mounting module Anodized T-6 Aluminum 5.4 lbs.
9120-TSM-MMB-8432 Anodized T-6 Aluminum 5.4 lbs.TSM Pin and Bushing Tooling Interface Plate Anodized T-6 Aluminum 3.0 - 5.8 lbs.
9120-TSM-HBQ-9566 Anodized T-6 Aluminum 4.5 lbs9120-TSM-HBQ-8439 Anodized T-6 Aluminum 5.8 lbs.9120-TSM-VBB-8441 Anodized T-6 Aluminum 3.1 lbs.9120-TSM-VBQ-8442 Anodized T-6 Aluminum 3.0 lbs9120-TSM-MMBL-8432 Anodized T-6 Aluminum TBD9120-TSM-HBBL-9223 Anodized T-6 Aluminum 5.5 lbs 9120-TSM-HBQL-10189 Anodized T-6 Aluminum 4 lbs9120-TSM-VBBl-8441 Anodized T-6 Aluminum TBD
8.3 TSM V-Block System ComponentsPart Description Material Weight-MassTooling Pins Stainless Steel .01 - .5 lbs.TSM Horizontal modules and Extensions Anodized T-6 Aluminum Varies.
TSM Pin Receiver 4140HardenedSteelBlackOxide 1.25 lbs.TSM Tooling Interface Plate Anodized T-6 Aluminum 1.6 - 6.6 lbs.9120-TSM-HVQ-4055 Anodized T-6 Aluminum 1.76 lbs.9120-TSM-HVQ-4627 Anodized T-6 Aluminum 1.76 lbs.9120-TSM-HVQ-4056 Anodized T-6 Aluminum 1.95 lbs.9120-TSM-HVQ-4057 Anodized T-6 Aluminum 2.12 lbs.9120-TSM-HVQ-6660 Anodized T-6 Aluminum 2.63 lbs.9120-TSM-HVQ-7290 Anodized T-6 Aluminum 3.03 lbs.9120-TSM-HVB-7961 Anodized T-6 Aluminum 6.59 lbs.9120-TSM-VVB-4069 Anodized T-6 Aluminum 1.61 lbs.9120-TSM-VVB-4071 Anodized T-6 Aluminum 2.70 lbs.TSM Mounting modules Anodized T-6 Aluminum 5 - 7 lbs.TSM Adapter module Anodized T-6 Aluminum 2.2 lbs
8.4 TSM Tool Hanger System ComponentsPart Description Material Weight-MassTSM Tool Hanger Mounting module Anodized T-6 Aluminum .8 lbs.
TSM Tool Hanger Anodized T-6 Aluminum .5 - .6 lbs.9120-TSM-TH-5891 Anodized T-6 Aluminum .531 lbs.9120-TSM-TH-5923 Anodized T-6 Aluminum .516 lbs9120-TSM-TH-5497 Anodized T-6 Aluminum .563 lbs.TSM Alignment Pins Stainless Steel .036 lbs.
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 45
9. Drawings9.1 Pin and Bushing Mounting Module
3rd
AN
GLE
PRO
JEC
TION
146
.1
177
.8
22.
7
119
.4
106
.8
29.
2
27.
9
59.
7
16.9
M12
SH
CS
12.9
M8
SH
CS
2X M
3X0.
5 6
3X M
8X1.
25
16
59.
1
Stan
dard
Mou
ntin
g H
ardw
are
4X M
12 S
HC
SP
re /
62 ft
-lbs
Not
e 1
Extr
uded
Rai
l Mou
ntin
g H
ardw
are
4X M
8 S
HC
SP
re /
190
in-lb
sN
ote
1
4X M
8 T-
Nut
Not
e 1
8X M
8X1.
25
16
5X
12.
7 5
X 1
52.4
2X
10.
2
M8X
1.25
1
6
2X
38.
1
2X
38.
1
2X
38.
1
32.
4
2X
66.
4
2X
63.
5
2X
45
2X
50.
8
2X
54.
1
2X
28.
3
2X
38.
6
2X
45
1
2
Not
es:
Fast
ener
s sh
ippe
d lo
ose.
1.M
ater
ial -
Pin
s &
Bus
hing
- A
2 To
ol S
teel
2.
Pla
te -
6061
-T6
Alu
min
um, s
oft c
oat b
lack
ano
dize
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W9/
23/2
013
Ser
vice
able
Item
s
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
12
3700
-20-
8434
TSM
Pin
& B
ushi
ng, A
lignm
ent P
in, D
ual T
aper
21
3700
-20-
8436
Dril
l Bus
hing
, Fla
nged
, Elo
ngat
ed, 1
6mm
ID
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-M
MB
-843
2TS
M P
in &
Bus
hing
Mou
ntin
g M
odul
e - R
igid
B1:
31
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 9/2
3/13
D. N
orto
n, 1
0/23
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-M
MB
-843
213
0510
-501
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Pin
& B
ushi
ng M
ount
ing
Mod
ule
- Rig
id
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 46
9.2 Mounting Module 3597
3rd
AN
GLE
PRO
JEC
TION
90D
owel
s
35
66.
6
83
99
45
90
23
130
53
43
4X M
8 S
HC
S24
2 / 1
40 in
-lbs
Not
e 1
2X
M8
Dow
elN
ote
2
Not
es:
Cus
tom
er to
use
Loc
tite
or s
imila
r thr
eadl
ocke
r and
torq
ue fa
sten
ers
to li
sted
torq
ue.
1.C
usto
mer
to p
ress
dow
els
into
mou
ntin
g pl
ate
if ne
eded
.2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-M
MV
-359
7TS
M M
ount
ing
Mod
ule,
V-B
lock
B1:
21
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-M
MV-
3597
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Mou
ntin
g M
odul
e, V
-Blo
ck
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 47
9.3 Mounting Module 4018
3rd
AN
GLE
PRO
JEC
TION
90D
owel
s
35
90
23
45
99 8
2
165
47
62
4X M
8 S
HC
S24
2 / 1
40 in
-lbs
Not
e 1
2X
M8
Dow
elN
ote
2
Not
es:
Cus
tom
er to
use
Loc
tite
or s
imila
r thr
eadl
ocke
r and
torq
ue fa
sten
ers
to li
sted
torq
ue.
1.C
usto
mer
to p
ress
dow
els
into
mou
ntin
g pl
ate
if ne
eded
.2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
B1:
21
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-M
MV-
4018
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Mou
ntin
g M
odul
e, V
-Blo
ck, L
arge
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 48
9.4 Pin and Bushing QC-50 Tooling Plate
3rd
AN
GLE
PRO
JEC
TION
R69
.9
174
2X
31.
8 2
X 6
0
2X
30
2X
5
74.
9
149
.9
QC
-50
Mou
ntin
g P
atte
rnS
ee 9
630-
20-0
50
128
.3
147
.3
121
.9
152
.1
22.
8
105
.5
10(M
8 S
HC
S)
5.3
(M8
Dow
els)
11
3
24
Cus
tom
er c
anm
achi
ne p
atte
rnas
nee
ded
6X M
8 x
20 S
HC
SP
re /
190
in-lb
sN
ote
1
Not
es:
Fast
ener
s &
Dow
els
ship
ped
loos
e. T
o be
inst
alle
d by
cus
tom
er.
1.P
late
mat
eria
l: 60
61-T
6 A
lum
inum
, sof
t coa
t bla
ck a
nodi
ze.
2.W
eigh
t: ap
prox
. 8.9
lbs.
3.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gD
JB1/
21/2
016
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
BQ
-956
6TS
M T
oolin
g In
terfa
ce P
late
QC
-50
- Bla
nk
Ser
vice
able
Item
sIT
EM
NO
.QTY
.PA
RT
NU
MB
ER
DE
SC
RIP
TIO
N1
235
40-0
1080
20-1
18m
m x
20m
m D
owel
Allo
y S
teel
21
3700
-20-
8434
TSM
Pin
& B
ushi
ng, A
lignm
ent P
in, D
ual T
aper
31
3700
-20-
8435
Dril
l Bus
hing
, Fla
nged
, 16m
m ID
41
3700
-20-
8436
Dril
l Bus
hing
, Fla
nged
, Elo
ngat
ed, 1
6mm
ID
B1:
31
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
D. B
ohle
1/2
1/20
16
J. W
inte
rroth
3/1
/201
6
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
BQ
-956
615
0928
-101
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-50
- Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 49
9.5 Pin and Bushing QC-76 Tooling Plate
3rd
AN
GLE
PRO
JEC
TION
2X
31.
8 7
4.9
149
.9 2
X 6
0
2X
30
2X
5
171
.5
R82
.6
QC
-76
Mou
ntin
g P
atte
rnS
ee 9
630-
20-0
76
128
.3
152
.1
147
.3
121
.9
9(M
10 D
owel
s)
17.6
(M10
SH
CS
)
22.
8
105
.5
11
3
24
Cus
tom
er c
anm
achi
ne p
atte
rnas
nee
ded
6X M
10 x
25
SH
CS
Pre
/ 42
0 in
-lbs
Not
e 1
Not
es:
Fast
ener
s &
Dow
els
ship
ped
loos
e. T
o be
inst
alle
d by
cus
tom
er.
1.P
late
mat
eria
l: 60
61-T
6 A
lum
inum
, sof
t coa
t bla
ck a
nodi
ze.
2.W
eigh
t: ap
prox
. 8.9
lbs.
3.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gD
AW
2/27
/201
5
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
BQ
-922
4TS
M T
oolin
g In
terfa
ce P
late
for Q
C-7
6 - B
lank
Ser
vice
able
Item
sIT
EM
NO
.QTY
.PA
RT
NU
MB
ER
DE
SC
RIP
TIO
N1
235
40-0
1100
20-1
1D
OW
EL
PIN
M10
x 2
02
137
00-2
0-84
34TS
M P
in &
Bus
hing
, Alig
nmen
t Pin
, Dua
l Tap
er3
137
00-2
0-84
35D
rill B
ushi
ng, F
lang
ed, 1
6mm
ID4
137
00-2
0-84
36D
rill B
ushi
ng, F
lang
ed, E
long
ated
, 16m
m ID
B1:
31
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
D. W
oode
n 02
/27/
15
J. W
inte
rroth
03/
04/1
5
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
BQ
-922
413
0510
-501
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-76
- Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 50
9.6 Pin and Bushing QC-110 Tooling Plate
3rd
AN
GLE
PRO
JEC
TIONCus
tom
er c
an m
achi
neto
ol p
atte
rn a
s ne
eded
2X M
10 x
20
Dow
els
Not
e 1
6X M
10 x
25
SH
CS
Pre
/ 42
0 in
-lbs
Not
e1
4
2
3
1
152
.1
128
.3
147
.3
121
.9
254
149
.9
165
.1
74.
9 2
X 3
1.8
2X
60
2X
5
2X
30
4X M
5X0.
8 1
0.2
QC
-110
Mou
ntin
g P
atte
rnS
ee 9
630-
20-1
10
6(M
10 D
owel
s)17
.6(M
10 S
HC
S)
105
.5
200
.7
22.
8
Not
es:
Fast
ener
s &
Dow
els
ship
ped
loos
e. T
o be
inst
alle
d by
cus
toem
er.
1.P
late
mat
eria
l: 6
061-
T6 A
lum
inum
, sof
t coa
t bla
ck a
nodi
ze.
2.P
late
wei
ght:
appr
ox 6
lbs.
3.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W9/
23/2
013
Ser
vice
able
Item
s
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
12
3540
-011
0020
-11
DO
WE
L P
IN M
10 x
20
21
3700
-20-
8434
TSM
Pin
& B
ushi
ng, A
lignm
ent P
in, D
ual T
appe
r3
137
00-2
0-84
35D
rill B
ushi
ng, F
lang
ed, 1
6mm
ID4
137
00-2
0-84
36D
rill B
ushi
ng, F
lang
ed, E
long
ated
, 16m
m ID
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
BQ
-843
9TS
M T
oolin
g In
terfa
ce P
late
for Q
C-1
10 -
Bla
nk
B1:
31
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 9/2
3/13
D. N
orto
n, 1
0/23
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
BQ
-843
913
0510
-501
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-110
- Bl
ank
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 51
9.7 Pin and Bushing Horizontal Blank Tooling Plate
3rd
AN
GLE
PRO
JEC
TION
149
.9
2X
31.
8 2
X 6
0 2
X 5
254
2X
30
74.
9
128
.3
152
.1
147
.3
121
.9
105
.5
200
.7
22.
8
1
1
32
Cus
tom
er c
anm
achi
ne to
ol p
atte
rnas
nee
ded
Not
es:
Pla
te m
ater
ial:
6061
-T6
Alu
min
um, s
oft c
oat b
lack
ano
dize
.1.
Wei
ght:
appr
ox 5
.5 lb
s2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gD
AW
2/24
/201
5
02EC
O 1
4647
: Rem
oved
Not
e "F
ast
ener
s & D
owel
s shi
pp
ed lo
ose.
To
be
inst
alle
d b
y cu
stom
er."
TBC
9/1/
2016
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
BB
-922
3TS
M T
oolin
g In
terfa
ce P
late
- B
lank
Ser
vice
able
Item
sIT
EM
NO
.QTY
.PA
RT
NU
MB
ER
DE
SC
RIP
TIO
N1
137
00-2
0-84
34TS
M P
in &
Bus
hing
, Alig
nmen
t Pin
, Dua
l Tap
er2
137
00-2
0-84
35D
rill B
ushi
ng, F
lang
ed, 1
6mm
ID3
137
00-2
0-84
36D
rill B
ushi
ng, F
lang
ed, E
long
ated
, 16m
m ID
B1:
31
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
D. W
oode
n 02
/24/
15
J. W
inte
rroth
03/
04/1
5
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
BB-9
223
1305
10-5
02
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te -
Blan
k
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 52
9.8 Pin and Bushing Vertical Blank Tooling Plate
3rd
AN
GLE
PRO
JEC
TION
127
1
52.4
149
.9
74.
9
Cus
tom
er c
an m
achi
neto
ol p
atte
rn a
s ne
eded
61
2X
45.
7
2X
15.
2
119
.4
2X
5
2X
30
2X
60
2X
29.
5 4X
Pilo
t T
hru
M5X
0.8
10.
2
22.
8 96.
5
17.
8
27.
9
3
2
1
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W9/
23/2
013
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-V
BB
-844
1TS
M T
oolin
g In
terfa
ce P
late
- B
lank
Ser
vice
able
Item
s
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
3700
-20-
8434
TSM
Pin
& B
ushi
ng, A
lignm
ent P
in, D
ual T
appe
r2
137
00-2
0-84
35D
rill B
ushi
ng, F
lang
ed, 1
6mm
ID3
137
00-2
0-84
36D
rill B
ushi
ng, F
lang
ed, E
long
ated
, 16m
m ID
B1:
21
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLI
MET
ERS.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 9/2
3/13
D. N
orto
n, 1
0/23
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-V
BB
-844
113
0510
-501
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te -
Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 53
9.9 Pin and Bushing J16 Tooling Plate
3rd
AN
GLE
PRO
JEC
TION
127
1
52.4
74.
9
3X
50
57.
2 9
9
4X
4.5
0 Th
ru 8
.3
5.5
From
Oth
er S
ide
2X
4 4 Th
ru(Ø
4mm
Dow
el P
F) 3
X 4
9.9
149
.9
55.
9
A A
2X
45.
7 6
1
15.
2
119
.4
2X
29.
5 6
0 2
X 5
2X
30
4X P
ilot
Thr
u M
5X0.
8 1
0.2
1
3
2
27.
9
96.
5
22.
8
2.5
17.
8
6Fa
sten
er5 Dow
el 5
.5
SE
CTI
ON
A-A
Rev.
Des
crip
tion
Initi
ato
rD
ate
02C
hang
e to
912
0-TS
M-V
BQ-8
442
JMW
04/1
7/20
15
Ser
vice
able
Item
sIT
EM
NO
.Q
TY.
PA
RT
NU
MB
ER
DE
SC
RIP
TIO
N1
137
00-2
0-84
34TS
M P
in &
Bus
hing
, Alig
nmen
t Pin
, Dua
l Tap
per
21
3700
-20-
8436
Dril
l Bus
hing
, Fla
nged
, Elo
ngat
ed, 1
6mm
ID3
137
00-2
0-84
35D
rill B
ushi
ng, F
lang
ed, 1
6mm
ID
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-V
BQ
-844
2TS
M T
oolin
g In
terfa
ce P
late
- J1
6 P
atte
rn
B1:
21
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 9/2
3/13
D. N
orto
n, 1
0/23
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-V
BQ-8
442
1305
10-5
02
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te -
J16
Patte
rn
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 54
9.10 TSM Pin & Bushing Mounting Module - Rigid - Locking
3rd
AN
GLE
PRO
JEC
TION
74
6
3
52
1
Not
e 2
& 3
7649
-242
/ 15
0 in
-lbs
222
/ 89
in-lb
sN
ote
1222
/ 15
in-lb
s
Not
e 2
& 3
Not
e 2
& 3
Not
e 1,
4
8
For 9
120-
TSL-
ASY
-XXX
X
Pre
/ 62
ft-lb
s
For 9
120-
TSM
-ASY
-XXX
X
Pre
/ 19
0 in
-lbs
9005
-20-
8444
Ret
urn
to s
tock
Not
e 1
Not
es:
Incl
uded
with
900
5-20
-844
4.1.
If as
sem
blin
g to
912
0-TS
L-A
SY
-XX
XX
use
M12
SH
CS
. B
ag M
8 S
HC
S &
T-fa
sten
ers.
2.
Oth
erw
ise
bag
loos
e ite
ms.
If as
sem
blin
g to
912
0-TS
M-A
SY
-XX
XX
use
M8
SH
CS
& T
-fast
ener
s.
3.O
ther
wis
e ba
ge lo
ose
item
s.B
ag lo
ose
parts
.4.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01P
Initi
al D
raw
ing
JMW
1/08
/201
6
02P
Upd
ate
d to
use
900
5-20
-844
4.JM
W1/
12/2
016
03Pr
ojec
t Rel
ease
JMW
6/30
/201
6
ITE
M N
O.
QTY
PA
RT
NU
MB
ER
DE
SC
RIP
TIO
N1
435
00-1
0680
35-1
5AM
8-1.
25 x
35m
m S
HC
S, B
lue,
Pre
-App
lied
24
3500
-107
2035
-15A
M12
-1.7
5 x
35m
m S
HC
S, B
lue,
Pre
-App
lied
32
3500
-116
4006
-21
M5
x 6m
m B
utto
n H
ead
Soc
ket C
ap S
crew
, SS
44
3505
-996
8000
-00
Bos
ch T
-Fas
tene
r #38
4221
8993
52
3690
-000
0068
-61
Cab
le C
lip, N
ylon
, Fle
xibl
e, 1
/4" M
ax B
undl
e6
137
00-2
0-84
32TS
M P
in &
Bus
hing
, Rig
id N
est P
late
72
3700
-20-
8434
TSM
Pin
& B
ushi
ng, A
lignm
ent P
in, D
ual T
aper
81
9005
-20-
8444
TSM
Pin
& B
ushi
ng R
etro
fit L
ocki
ng A
ssem
bly
B1:
21
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
IN
CHE
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
01/1
5
D. N
orto
n, 1
/08/
16
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 91
20-T
SM-M
MBL
-843
214
0507
-103
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Pin
& B
ushi
ng M
ount
ing
Mod
ule
- Rig
id -
Lock
ing
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 55
9.11 PinandBushingRetrofitLockingAssembly
3rd
AN
GLE
PRO
JEC
TION
8
9
4
1
1
3
6
5N
ote
1
Not
e 1
Not
e 1
2
7
Con
tact
+ 1
/4 tu
rn
Con
tact
+ 1
/4 tu
rn
242
/ 10
in-o
z
242
/ Tig
hten
to c
onta
ctO
rient
as
show
n Not
e 2
10N
ote
1
DE
TAIL
AS
CA
LE 4
: 3
Inst
all e
long
ated
bus
hing
with
alig
nmen
t gro
oves
para
llel t
o al
ignm
ent g
roov
es o
n B
ushi
ng B
lock
.
.312
Ens
ure
dow
els
do n
otin
terfe
re w
ith s
enso
rac
cess
hol
e.
Not
es:
Pac
kage
loos
e ite
ms.
1.R
efer
to li
nked
wor
k in
stru
ctio
ns.
2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01P
Initi
al D
raw
ing
JMW
9/17
/201
5
02Pr
ojec
t Rel
ease
JMW
6/30
/201
6
ITE
M N
O.Q
TY.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
12
3405
-122
0030
-01
Qui
ck D
isco
nnec
t Red
ucer
, 8m
m to
6m
m T
ube
21
3405
-123
0018
-01
Air
Fitti
ng, S
traig
ht M
ale
Con
nect
or, 1
/8" U
nifit
to 8
mm
One
-Tou
ch3
134
05-2
2300
10-0
190
° A
ir Fi
tting
, 1/8
" Uni
fit to
8m
m T
ube,
One
-Tou
ch
41
3415
-101
1010
-01
SM
C A
ir C
ylin
der,
Dou
ble
Act
ing,
3/4
" Bor
e, 1
" Stro
ke, 1
/8" N
PT
Por
ts,
Rou
nd R
od T
ip5
435
00-1
0660
40-1
5M
6-1
x 40
mm
SH
CS
, Blu
e6
235
00-1
9660
08-3
2M
6 x
8mm
Set
Scr
ew, N
ylon
-Tip
, Allo
y S
teel
72
3540
-010
6016
-11
6mm
x 1
6mm
Dow
el, A
lloy
Ste
el8
137
00-2
0-84
36D
rill B
ushi
ng, F
lang
ed, E
long
ated
, 16m
m ID
91
3700
-20-
8444
TSM
Pin
& B
ushi
ng B
lock
for L
ocki
ng N
est
101
3700
-20-
8443
TSM
Pin
& B
ushi
ng, A
lignm
ent P
in, D
ual T
aper
, Loc
king
Rec
ess
B2:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
IN
CHE
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 9/2
2/14
D. N
orto
n, 1
/8/1
6
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 90
05-2
0-84
4414
0507
-102
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Pin
& B
ushi
ng R
etro
fit L
ocki
ng A
ssem
bly
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 56
9.12 Horizontal Tooling Interface Plate-Blank (Locking)
3rd
AN
GLE
PRO
JEC
TION
149
.9
2X
31.
8 2
X 6
0 2
X 5
254
2X
30
4X M
5X0.
8 1
0.2
74.
9
128
.3
159
.3
147
.3
121
.9
105
.5
200
.7
22.
8
1
1
32
Cus
tom
er c
anm
achi
ne to
ol p
atte
rnas
nee
ded
Not
es:
Fast
ener
s &
Dow
els
ship
ped
loos
e. T
o be
inst
alle
d by
cus
tom
er.
1.P
late
mat
eria
l: 60
61-T
6 A
lum
inum
, sof
t coa
t bla
ck a
nodi
ze.
2.W
eigh
t: ap
prox
5.5
lbs
3.
Rev.
Des
crip
tion
Initi
ator
Dat
e
02EC
O 1
6373
: Upd
ated
cus
tom
er d
raw
ing
to re
flect
ad
diti
on o
f TSM
-MA
03 m
ount
ing
patte
rn to
TSM
inte
rface
pla
te. A
dd
ed "4
X M
5X0.
8 1
0.2"
to T
op V
iew
.TB
C1/
12/2
018
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
BB
L-92
23TS
M T
oolin
g In
terfa
ce P
late
- B
lank
- Lo
ckin
g
Ser
vice
able
Item
sIT
EM
NO
.QTY
.PA
RT
NU
MB
ER
DE
SC
RIP
TIO
N1
137
00-2
0-84
43TS
M P
in &
Bus
hing
, Alig
nmen
t Pin
, Dua
l Tap
er,
Lock
ing
Rec
ess
21
3700
-20-
8435
Dril
l Bus
hing
, Fla
nged
, 16m
m ID
31
3700
-20-
8436
Dril
l Bus
hing
, Fla
nged
, Elo
ngat
ed, 1
6mm
ID
B1:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 4/1
8/16
D. N
orto
n, 4
/19/
16
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
BBL-
9223
1405
07-1
02
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te -
Blan
k - L
ocki
ng
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 57
9.13 Tooling Interface Plate for QC 40- Blank- MA03 (Locking)
3rd
AN
GLE
PRO
JEC
TION
128
.3
159
.3
147
.3
121
.9
4X M
5X0.
8 1
0.2
5 3
0
31.
8 6
0 149
.9
142
.2
196
.8
111
.8
QC
-40
MO
UN
TIN
G P
ATTE
RN
SEE
9230
-20-
1966
143
.5
105
.5
22.
8
15.6
(M8
SHC
S)9.
4(M
8 D
OW
ELS)
5
4
32
1
NO
TE 1
PRE
/ 190
IN-L
BSN
OTE
1
NO
TES:
FAST
ENER
S AN
D D
OW
ELS
SHIP
PED
LO
OSE
. TO
BE
INST
ALLE
D B
Y C
UST
OM
ER.
1.PL
ATE
MAT
ERIA
L: 6
061-
T6 A
LUM
INU
M, S
OFT
CO
AT B
LAC
K AN
OD
IZE.
2.PL
ATE
WEI
GH
T: A
PPR
OX
4.1
LBS
3.
REV
.D
ESC
RIPT
ION
INITI
ATO
RD
ATE
01IN
ITIA
L D
RAW
ING
JMW
2/22
/201
8
SER
VIC
EABL
E IT
EMS
ITEM
NO
.Q
TYPA
RT
NU
MBE
RD
ESC
RIP
TIO
N
11
370
0-20
-844
3TS
M P
in &
Bus
hing
, Alig
nmen
t Pin
, Dua
l Ta
per,
Lock
ing
Rec
ess
21
370
0-20
-843
6D
rill B
ushi
ng, F
lang
ed, E
long
ated
, 16m
m ID
31
370
0-20
-843
5D
rill B
ushi
ng, F
lang
ed, 1
6mm
ID4
6 3
500-
1068
025-
15A
M8-
1.25
x 2
5mm
SH
CS,
Blu
e, P
re-A
pplie
d5
2 3
540-
0108
020-
118m
m x
20m
m D
owel
Allo
y St
eel
B1:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 2/2
2/18
D. N
orto
n, 5
/09/
18
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
BQL-
1018
916
1215
-101
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-40
- Bla
nk -
MA0
3
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 58
9.14 Vertical Tooling Interface Plate - Blank (Locking)
3rd
AN
GLE
PRO
JEC
TION
149
.9
127
159
.5
74.
9
CU
STO
MER
TO
MAC
HIN
ETO
OL
PATT
ERN
AS
NEE
DED
2X
45.7
6
1
2X
5
2X
30
15.
2
2X
29.5
119
.4
2X
60
4X M
5X0.
8 1
0.2
27.
9
96.
5
22.
8
17.
8
3
2
4
REV
.D
ESC
RIPT
ION
INITI
ATO
RD
ATE
02EC
O 1
6373
: Upd
ated
cus
tom
er d
raw
ing
to re
flect
add
ition
of
TSM
-MA
03 m
ount
ing
patte
rn to
TSM
inte
rface
pla
te.
TBC
1/12
/201
8
ITEM
NO
.Q
TY.
PAR
T N
UM
BER
DES
CR
IPTI
ON
11
9120
-TSM
-VBB
L-84
41TS
M V
ertic
al T
oolin
g In
terfa
ce P
late
- Bl
ank
- Loc
king
SER
VIC
ABLE
ITEM
SIT
EM N
O.
QTY
PAR
T N
UM
BER
DES
CR
IPTI
ON
21
3700
-20-
8435
Dril
l Bus
hing
, Fla
nged
, 16m
m ID
31
3700
-20-
8436
Dril
l Bus
hing
, Fla
nged
, Elo
ngat
ed, 1
6mm
ID4
137
00-2
0-84
43TS
M P
in &
Bus
hing
, Alig
nmen
t Pin
, Dua
l Tap
er, L
ocki
ng R
eces
s
B1:
21
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIED
.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 8/1
7/17
K. Z
acha
ry, 8
/17/
17
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #SH
EET
O
F 96
30-2
0-TS
M-V
BBL-
8441
1708
02-5
02
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT T
O B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT O
N O
RDER
OR
WITH
PRI
OR
WRI
TTEN
AUT
HORI
ZATIO
N O
F A
TI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Ver
tical
Too
ling
Inte
rface
Pla
te -
Blan
k - L
ocki
ng
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 59
9.15 Pin and Bushing QC-50 Tooling Plate
3rd
AN
GLE
PRO
JEC
TION
R69
.9
174
2X
31.
8 2
X 6
0
2X
30
2X
5
74.
9
149
.9
QC
-50
Mou
ntin
g P
atte
rnS
ee 9
630-
20-0
50
128
.3
147
.3
121
.9
152
.1
22.
8
105
.5
10(M
8 S
HC
S)
5.3
(M8
Dow
els)
11
3
24
Cus
tom
er c
anm
achi
ne p
atte
rnas
nee
ded
6X M
8 x
20 S
HC
SP
re /
190
in-lb
sN
ote
1
Not
es:
Fast
ener
s &
Dow
els
ship
ped
loos
e. T
o be
inst
alle
d by
cus
tom
er.
1.P
late
mat
eria
l: 60
61-T
6 A
lum
inum
, sof
t coa
t bla
ck a
nodi
ze.
2.W
eigh
t: ap
prox
. 8.9
lbs.
3.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gD
JB1/
21/2
016
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
BQ
-956
6TS
M T
oolin
g In
terfa
ce P
late
QC
-50
- Bla
nk
Ser
vice
able
Item
sIT
EM
NO
.QTY
.PA
RT
NU
MB
ER
DE
SC
RIP
TIO
N1
235
40-0
1080
20-1
18m
m x
20m
m D
owel
Allo
y S
teel
21
3700
-20-
8434
TSM
Pin
& B
ushi
ng, A
lignm
ent P
in, D
ual T
aper
31
3700
-20-
8435
Dril
l Bus
hing
, Fla
nged
, 16m
m ID
41
3700
-20-
8436
Dril
l Bus
hing
, Fla
nged
, Elo
ngat
ed, 1
6mm
ID
B1:
31
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
D. B
ohle
1/2
1/20
16
J. W
inte
rroth
3/1
/201
6
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
BQ
-956
615
0928
-101
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-50
- Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 60
9.16 Mounting Module 3597
3rd
AN
GLE
PRO
JEC
TION
90D
owel
s
35
66.
6
83
99
45
90
23
130
53
43
4X M
8 S
HC
S24
2 / 1
40 in
-lbs
Not
e 1
2X
M8
Dow
elN
ote
2
Not
es:
Cus
tom
er to
use
Loc
tite
or s
imila
r thr
eadl
ocke
r and
torq
ue fa
sten
ers
to li
sted
torq
ue.
1.C
usto
mer
to p
ress
dow
els
into
mou
ntin
g pl
ate
if ne
eded
.2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-M
MV
-359
7TS
M M
ount
ing
Mod
ule,
V-B
lock
B1:
21
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-M
MV-
3597
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Mou
ntin
g M
odul
e, V
-Blo
ck
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 61
9.17 Mounting Module 4018
3rd
AN
GLE
PRO
JEC
TION
90D
owel
s
35
90
23
45
99 8
2
165
47
62
4X M
8 S
HC
S24
2 / 1
40 in
-lbs
Not
e 1
2X
M8
Dow
elN
ote
2
Not
es:
Cus
tom
er to
use
Loc
tite
or s
imila
r thr
eadl
ocke
r and
torq
ue fa
sten
ers
to li
sted
torq
ue.
1.C
usto
mer
to p
ress
dow
els
into
mou
ntin
g pl
ate
if ne
eded
.2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
B1:
21
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-M
MV-
4018
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Mou
ntin
g M
odul
e, V
-Blo
ck, L
arge
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 62
9.18 QC-40 Tooling Interface Plate
3rd
AN
GLE
PRO
JEC
TION
96
12.
7
193
115
34
66.
6
Inte
rface
for Q
C-4
0 To
ol
52
11.
7
M8
Dow
elN
ote
2
6X M
8 S
HC
SP
re /
120
in-lb
sN
ote
1
Not
es: Cus
tom
er to
inst
all p
re-a
pplie
d fa
sten
ers
and
torq
ue to
list
ed v
alue
.1.
Cus
tom
er to
inst
all d
owel
pin
s in
to Q
C-4
0 To
ol B
ody.
2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
VQ
-405
5TS
M T
oolin
g In
terfa
ce P
late
for Q
C-4
0 - B
lank
B1:
21
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
VQ
-405
5-
01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-40
- Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 63
9.19 QC-41 Tooling Interface Plate
3rd
AN
GLE
PRO
JEC
TION
130
12.
7
96
66.
6
34
193
Inte
rface
for Q
C-4
1 To
ol
11.
7 5
2
M8
Dow
elN
ote
2
6X M
8 S
HC
SP
re /
120
in-lb
sN
ote
1
Not
es: Cus
tom
er to
inst
all p
re-a
pplie
d fa
sten
ers
and
torq
ue to
list
ed v
alue
.1.
Cus
tom
er to
inst
all d
owel
pin
s in
to Q
C-4
1 To
ol B
ody.
2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
VQ
-405
6TS
M T
oolin
g In
terfa
ce P
late
for Q
C-4
1 - B
lank
B1:
21
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
VQ
-405
6-
01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-41
- Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 64
9.20 QC-60 Tooling Interface Plate
3rd
AN
GLE
PRO
JEC
TION
101
.6
15.
9
96
66.
6
34
201
Inte
rface
for Q
C-6
0 To
ol
8.5
5
2.1
6X M
8 S
HC
SP
re /
120
in-lb
sN
ote
1
M8
Dow
elN
ote
2
Not
es: Cus
tom
er to
inst
all p
re-a
pplie
d fa
sten
ers
and
torq
ue to
list
ed v
alue
.1.
Cus
tom
er to
inst
all d
owel
pin
s in
to Q
C-6
0 To
ol B
ody.
2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
B1:
21
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLI
MET
ERS.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
VQ
-405
7-
01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-60
- Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 65
9.21 QC-62 Tooling Interface Plate
3rd
AN
GLE
PRO
JEC
TION
132
.3
15.
9
96
66.
6
202
34
Inte
rface
for Q
C-6
2 To
ol
52
12.
5
6X M
8 S
HC
SP
re /
120
in-lb
sN
ote
1M8
Dow
elN
ote
2
Not
es: Cus
tom
er to
inst
all p
re-a
pplie
d fa
sten
ers
and
torq
ue to
list
ed v
alue
.1.
Cus
tom
er to
inst
all d
owel
pin
s in
to Q
C-6
2 To
ol B
ody.
2.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
VQ
-666
0TS
M T
oolin
g In
terfa
ce P
late
for Q
C-6
2 - B
lank
B1:
31
1RE
VIS
ION
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
VQ-6
660
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-62
- Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 66
9.22 QC-71 Tooling Interface Plate
3rd
AN
GLE
PRO
JEC
TION
16.
5
96
66.
6
34
224
148
7.9
5
2
Inte
rface
for Q
C-7
1 To
ol
6X M
8 S
HC
SP
re /
120
in-lb
sN
ote
1
M8
Dow
elN
ote
2
Not
es: C
usto
mer
to in
stal
l pre
-app
lied
fast
ener
s an
d to
rque
to li
sted
val
ue.
1.C
usto
mer
to in
stal
l dow
el p
in in
to Q
C-7
1 To
ol B
ody.
2.
Rev.
Des
crip
tion
Initi
ator
Dat
e
01In
itial
Dra
win
gJM
W02
/06/
2014
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
VQ
-405
8TS
M T
oolin
g In
terfa
ce P
late
for Q
C-7
1 - B
lank
B1:
21
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 2/0
6/14
D. N
orto
n, 2
/06/
14
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
VQ-4
058
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-71
- Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 67
9.23 QC-76 Tooling Interface Plate
3rd
AN
GLE
PRO
JEC
TION
222
66.
6
96
16.
5
139
Inte
rface
for Q
C-7
6 To
ol
18.
9
52
2X
M10
Dow
elN
ote
2
6X M
10 S
HC
SP
re /
220
in-lb
sN
ote
1
Not
es: Cus
tom
er to
inst
all p
re-a
pplie
d fa
sten
ers
and
torq
ue to
list
ed v
alue
1.C
usto
mer
to in
stal
l dow
el p
ins
into
QC
-76
Tool
Bod
y.2.
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
VQ
-729
0TS
M T
oolin
g In
terfa
ce P
late
for Q
C-
76 -
Bla
nk
Rev.
Des
crip
tion
Initi
ator
Dat
e
01In
itial
Dra
win
gD
AW
1/7/
2015
B1:
51
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
D. W
oode
n 1/
7/20
15
KRZ
1/7/
2015
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
VQ-7
290
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-76
- Bla
nk
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 68
9.24 QC-100 Tooling Interface Plate
3rd
AN
GLE
PRO
JEC
TION
16.
5
96.
5
101
.6
37.
5
279
144
.8
18.
9
52.
7
Inte
rface
for Q
C-1
00 T
ool
M10
Dow
elN
ote2
6X M
10 S
HC
SP
re /
420
in-lb
sN
ote
1
Not
es: C
usto
mer
to in
stal
l pre
-app
lied
fast
ener
s an
d to
rque
to li
sted
val
ue.
1.C
usto
mer
to in
stal
l dow
el p
in in
to Q
C-7
1 To
ol B
ody.
2.
Rev.
Des
crip
tion
Initi
ator
Dat
e
01In
itial
Dra
win
gJM
W02
/06/
2014
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
VQ
-405
9TS
M T
oolin
g In
terfa
ce P
late
for Q
C-1
00 -
Bla
nk
B1:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 2/0
6/14
D. N
orto
n, 2
/06/
14
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
VQ-4
059
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te fo
r QC
-100
- Bl
ank
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 69
9.25 Blank Tooling Interface Plate
3rd
AN
GLE
PRO
JEC
TION
166
24.
1
97
101
.6
303
37
Not
e 1
53
Not
es:
Cus
tom
er to
add
mou
ntin
g pa
ttern
s as
nee
ded.
1.
Rev.
Des
crip
tion
Initi
ator
Dat
e
01In
itial
Dra
win
gJM
W12
/03/
2013
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-H
VB
-796
1TS
M T
oolin
g In
terfa
ce P
late
- B
lank
B1:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-H
VB-7
961
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
ling
Inte
rface
Pla
te -
Blan
k
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 70
9.26 Vertical Mounting Module 4068
3rd
AN
GLE
PRO
JEC
TION
66.
6
191
273
.6
130
42
130
29
4X M
8 S
HC
S24
2 / 1
40 in
-lbs
Not
e 1
2X
M8
Dow
elN
ote
3
4X M
12 S
HC
SP
re /
48 ft
-lbs
Not
e 2
45D
owel
s
45
45
45
22.
5
45
Not
es:
If as
sem
blin
g to
912
0-TS
M-A
SY
-XX
XX
, cus
tom
er to
use
Loc
tite
or s
imila
r thr
eadl
ocke
r and
1.
torq
ue fa
sten
ers
to li
sted
torq
ue.
If as
sem
blin
g to
912
0-TS
M-H
E-X
XX
X, c
usto
mer
to to
rque
pre
-app
lied
fast
ener
s to
list
ed to
rque
.2.
Cus
tom
er to
pre
ss d
owel
s in
to m
ount
ing
plat
e if
need
ed.
3.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
B1:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-M
MV-
4068
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Mou
ntin
g M
odul
e, V
-Blo
ck, V
ertic
al
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 71
9.27 Vertical Mounting Module 4070
3rd
AN
GLE
PRO
JEC
TION
66.
6
191
2
86
46
130
29.
1
4X M
12 S
HC
SP
re /
250
in-lb
sN
ote
2
4X M
8 S
HC
S24
2 / 1
40 in
-lbs
Not
e 1
2X
M8
Dow
elN
ote
3
45D
owel
s
45
45
22.
5 45
45
Not
es:
If as
sem
blin
g to
912
0-TS
M-A
SY
-XX
XX
, cus
tom
er to
use
Loc
tite
or s
imila
r thr
eadl
ocke
r and
1.
torq
ue fa
sten
ers
to li
sted
torq
ue.
If as
sem
blin
g to
912
0-TS
M-H
E-X
XX
X, c
usto
mer
to to
rque
pre
-app
lied
fast
ener
s to
list
ed to
rque
.2.
Cus
tom
er to
pre
ss d
owel
s in
to m
ount
ing
plat
e if
need
ed.
3.
ITE
M N
O.Q
TY.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-M
MV
-407
0TS
M M
ount
ing
Mod
ule,
V-B
lock
, Ver
tical
, Lar
ge
Rev.
Des
crip
tion
Initi
ato
rD
ate
02EC
O 1
2472
: C
hang
ed to
rque
from
48
ft-lb
s to
250
in-lb
s on
M12
SH
CS
callo
ut.
MSD
4/3/
2015
B1:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-M
MV-
4070
-02
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Mou
ntin
g M
odul
e, V
-Blo
ck, V
ertic
al, L
arge
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 72
9.28 Vertical Tooling Interface Plate - Blank
3rd
AN
GLE
PRO
JEC
TION
213
2
03.2
88.
9
47
66.
6 3
3.3
Not
e 1
12.
7
Not
es:
Cus
tom
er to
add
mou
ting
patte
rns
as n
eede
d.1.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-V
VB
-406
9TS
M V
ertic
al T
oolin
g In
terfa
ce P
late
- B
lank
B1:
21
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-V
VB-4
069
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Ver
tical
Too
ling
Inte
rface
Pla
te -
Blan
k
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 73
9.29 Vertical Tooling Interface Plate - Blank (Large)
3rd
AN
GLE
PRO
JEC
TION
223
99
88.
9
208
.3
66.
6 3
3.3
56
Not
e 1
18.
8
Not
es:
Cus
tom
er to
add
mou
ntin
g pa
ttern
s as
nee
ded.
1.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W12
/03/
2013
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-V
VB
-407
1TS
M V
ertic
al T
oolin
g In
terfa
ce P
late
- B
lank
(Lar
ge)
B1:
21
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 12/
03/1
3
D. N
orto
n, 1
2/04
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-V
VB-4
071
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Ver
tical
Too
ling
Inte
rface
Pla
te -
Blan
k (L
arge
)
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 74
9.30 Tool Hanger Module 5496
3rd
AN
GLE
PRO
JEC
TION
76.
2
59.
7
31.
2
63.
3
40.
2
45
14.
7
2X M
8 S
HC
SP
re /
120
in-lb
sN
ote
1
Opt
iona
l M8
T-nu
ts
for e
xtru
ded
rail
Not
es:
Cus
tom
er to
torq
ue p
re-a
pplie
d fa
sten
ers
to li
sted
torq
ue v
alue
.1.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W02
/25/
2014
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-M
M-5
496
TSM
Too
l Han
ger B
lock
B2:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 2/2
5/14
D. N
orto
n, 2
/27/
14
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-M
M-5
496
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Too
l Han
ger B
lock
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 75
9.31 Tool Hanger Module 5891
3rd
AN
GLE
PRO
JEC
TION
14
34.
3
94.
6 6
5.4
39.
8
58.
4
4.6
4X M
3 S
HC
SP
re /
12 in
-lbs
Not
e 2
1X M
8 S
CH
SS
7649
-242
/ 40
in-lb
sN
ote
3
Not
es:
Fast
ener
s sh
ippe
d lo
ose.
1.W
hen
inst
allin
g to
QC
-20/
21 in
stal
l M3
fast
ener
s fir
st.
2.C
usto
mer
to to
rque
pre
-app
lied
fast
ener
s to
list
ed to
rque
val
ue.
Cus
tom
er to
use
Loc
tite
or s
imila
r thr
ead
lock
er a
nd to
rque
to li
sted
torq
ue v
alue
.3.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W02
/25/
2014
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-T
H-5
891
Tool
Han
ger M
odul
e fo
r QC
20/2
1 Fl
at A
B2:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 2/2
5/14
D. N
orto
n, 2
/27/
14
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-T
H-5
891
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
Tool
Han
ger M
odul
e fo
r QC
20/2
1 Fl
at A
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 76
9.32 Tool Hanger Module 5923
3rd
AN
GLE
PRO
JEC
TION
14
34.
3
65.
4 9
4.6
50.
8
59.
7
7.1
2X M
4 S
HC
SP
re /
25 in
-lbs
Not
e 2
1X M
8 S
CH
SS
7649
-242
/ 40
in-lb
sN
ote
3
Not
es:
Fast
ener
s sh
ippe
d lo
ose.
1.W
hen
inst
allin
g to
QC
-21
inst
all M
4 fa
sten
ers
first
.2.
Cus
tom
er to
torq
ue p
re-a
pplie
d fa
sten
ers
to li
sted
torq
ue v
alue
.C
usto
mer
to u
se L
octit
e or
sim
ilar t
hrea
d lo
cker
and
torq
ue to
list
ed to
rque
val
ue.
3.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W02
/25/
2014
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-T
H-5
923
Tool
Han
ger M
odul
e fo
r QC
21 F
lat B
B2:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 2/2
5/14
D. N
orto
n, 2
/27/
14
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-T
H-5
923
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
Tool
Han
ger M
odul
e fo
r QC
-21,
Fla
t B
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 77
9.33 Tool Hanger Module 5497
3rd
AN
GLE
PRO
JEC
TION
14
40.
7
65.
4 9
4.6
59.
7
50.
8
5.1
1X M
8 S
CH
SS
7649
-242
/ 40
in-lb
sN
ote
3
4X M
4 S
HC
S22
2 / 2
5 in
-lbs
Not
e 2
Not
es:
Fast
ener
s sh
ippe
d lo
ose.
1.W
hen
inst
allin
g to
a Q
C T
ool B
ody
inst
all M
4 fa
sten
ers
first
.2.
Cus
tom
er to
use
Loc
tite
or s
imila
r thr
ead
lock
er a
nd to
rque
to li
sted
torq
ue v
alue
.C
usto
mer
to u
se L
octit
e or
sim
ilar t
hrea
d lo
cker
and
torq
ue to
list
ed to
rque
val
ue.
3.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
gJM
W02
/25/
2014
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-T
H-5
497
Tool
Han
ger M
odul
e fo
r J16
Fla
t
B2:
31
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 2/2
5/14
D. N
orto
n, 2
/27/
14
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-T
H-5
497
-01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
Tool
Han
ger M
odul
e fo
r J16
Fla
t
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 78
9.34 Post Modules
3rd
AN
GLE
PRO
JEC
TION
4X M
8 T-
Bol
t24
2 / 1
90 in
-lbs
Not
e 2
4X M
8 S
HC
SP
re /
190
in-lb
sN
ote
3
4X M
12 S
HC
SP
re /
250
in-lb
sN
ote
3
4X G
usse
t Kits
incl
uded
Not
e 1
36.0
914
Pos
t Hei
ght
T.O
.P.
18.8
Pla
te T
hick
ness
35
6
33
0 4X
13
Thr
u
Tab
Rem
oval
Inst
ruct
ions
:
Inse
rt a
scre
w d
river
into
the
slot
und
er th
e ta
b.1.
Pry
up
on th
e ta
b to
bre
ak it
off.
2.R
emov
e an
y bu
rrs
that
may
not
allo
w fl
ush
3.co
ntac
t to
the
base
ass
embl
y.
Not
es: Cus
tom
er to
rem
ove
Gus
set t
abs
from
the
mat
ing
surfa
ce th
at c
onta
cts
the
base
ass
embl
y.1.
Cus
tom
er to
use
Loc
tite
or s
imila
r thr
ead
lock
er a
nd to
rque
fast
ener
s to
list
ed to
rque
val
ue.
2.C
usto
mer
to in
stal
l pre
-app
lied
fast
ener
s an
d to
rque
to li
sted
torq
ue v
alue
.3.
Rem
ove
the
tabs
on
the
Gus
set f
ace
that
will
con
tact
th
e B
ase
asse
mbl
y
Pry
up
on a
tab
to
brea
k it
off
ITE
M N
O.
QTY
PA
RT
NU
MB
ER
DE
SC
RIP
TIO
N1
191
20-T
SM
-PM
-331
7TS
M P
ost M
odul
e, 0
914m
m (3
6") P
ost H
eigh
t - K
it
Rev.
Des
crip
tion
Initi
ato
rD
ate
02EC
O 1
3492
: Ad
ded
new
Not
e #
1 a
nd re
num
bere
d e
xistin
g N
otes
; Cha
nged
Not
e #
's on
cal
lout
s; A
dd
ed im
ages
& N
otes
d
etai
ling
tab
rem
oval
; "Ki
t" ad
ded
to P
ost M
odul
e d
escr
iptio
n.M
SD10
/27/
2015
B1:
61
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
D.B
rew
er, 1
1/08
/13
J. W
inte
rroth
, 11/
21/1
3
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-P
M-3
317
02
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Pos
t Mod
ule,
091
4mm
(36"
) Pos
t Hei
ght
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 79
9.35 TSM Rail Adapter Module - V-Block Style
3rd
AN
GLE
PRO
JEC
TION
45
45
101
.6
104
.1
4X M
8X1.
25
16
TSM
PIN
& B
USH
ING
MO
UN
TIN
G P
ATT
ERN
31.
5
20.
9
4X M
12 S
HC
SP
RE
/ 25
0 IN
-LB
SN
OTE
2
90
4X M
8X1.
25
16
45
2X
8.05
98.
034
12
(Ø8m
m D
OW
EL
SF)
TSM
V-B
LOC
K M
OU
NTI
NG
PA
TTER
N
45
45
NO
TES
:
FAS
TEN
ER
S S
HIP
PE
D L
OO
SE
.1.
WH
EN
INS
TALL
ING
TO
A T
SM
HO
RIZ
ON
TAL
EX
TEN
SIO
N C
US
TOM
ER
TO
US
E
2.P
RE
-AP
PLI
ED
FA
STE
NE
RS
OR
US
E L
OC
TITE
OR
SIM
ILA
R T
HR
EA
DLO
CK
ER
AN
D
TOR
QU
E F
AS
TEN
ER
S T
O T
HE
LIS
TED
TO
RQ
UE
VA
LUE
.
ITE
M N
O.
QTY
PA
RT
NU
MB
ER
DE
SC
RIP
TIO
N1
191
20-T
SM
-AM
-998
2TS
M A
dapt
er M
odul
e - M
ount
ing
Mod
ule
to T
SM
HE
SH
EE
TD
ES
CR
IPTI
ON
191
20-T
SM
-AM
-998
2 D
ETA
IL
291
20-T
SM
-MM
B-8
432
to 9
120-
TSM
-HE
-XX
XX
391
20-T
SM
-MM
V-4
018
to 9
120-
TSM
-HE
-XX
XX
REV
.D
ESC
RIPT
ION
INITI
ATO
RD
ATE
01IN
ITIA
L D
RAW
ING
JMW
3/14
/201
7
B1:
21
3RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 3/1
4/17
D. N
orto
n, 3
/14/
17
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-A
M-9
982
1606
30-4
01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Ada
pter
Mod
ule
- Mou
ting
Mod
ule
to T
SM H
E
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 80
3rd
AN
GLE
PRO
JEC
TION
9120
-TS
M-H
E-3
320
SH
OW
N.
OTH
ER
SIZ
ES
AV
AIL
AB
LE.
9120
-TS
M-M
MB
-843
2 S
HO
WN
.O
THE
R O
PTI
ON
S A
VA
ILA
BLE
.
4X M
8 S
HC
SP
RE
- 19
0 IN
-LB
SN
OTE
2
4X M
12 S
HC
SP
RE
/ 25
0 IN
-LB
SN
OTE
2
REV
.D
ESC
RIPT
ION
INITI
ATO
RD
ATE
-Se
e Sh
eet1
--
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-A
M-9
982
TSM
Ada
pter
Mod
ule
- Mou
ntin
g M
odul
e to
TS
M H
E2
191
20-T
SM
-HE
-332
0TS
M H
oriz
onta
l Ext
ensi
on, 6
"3
191
20-T
SM
-MM
B-8
432
TSM
Pin
& B
ushi
ng M
ount
ing
Mod
ule
- Rig
id
B1:
22
3RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 3/1
4/17
D. N
orto
n, 3
/14/
17
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-A
M-9
982
1606
30-4
01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Ada
pter
Mod
ule
- Mou
ting
Mod
ule
to T
SM H
E
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 81
3rd
AN
GLE
PRO
JEC
TION
9120
-TS
M-H
E-3
320
SH
OW
N.
OTH
ER
SIZ
ES
AV
AIL
AB
LE.
9120
-TS
M-M
MV
-401
8 S
HO
WN
.O
THE
R O
PTI
ON
S A
VA
ILA
BLE
.
4X M
8 S
HC
SP
RE
- 19
0 IN
-LB
SN
OTE
2
4X M
12 S
HC
SP
RE
/ 25
0 IN
-LB
SN
OTE
2
REV
.D
ESC
RIPT
ION
INITI
ATO
RD
ATE
-Se
e Sh
eet1
--
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-A
M-9
982
TSM
Ada
pter
Mod
ule
- Mou
ntin
g M
odul
e to
TS
M H
E2
191
20-T
SM
-HE
-332
0TS
M H
oriz
onta
l Ext
ensi
on, 6
"3
191
20-T
SM
-MM
B-8
432
TSM
Pin
& B
ushi
ng M
ount
ing
Mod
ule
- Rig
id
B1:
23
3RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 3/1
4/17
D. N
orto
n, 3
/14/
17
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-A
M-9
982
1606
30-4
01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Ada
pter
Mod
ule
- Mou
ting
Mod
ule
to T
SM H
E
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 82
9.36 Sensor Holders
3rd
AN
GLE
PRO
JEC
TION
27.
4
17.
8
8.9
19.
8
13.2
±0.0
7S
enso
r Dep
th
2X
3
16.
4 To
rque
jam
nut
to15
in-o
z
6.4
2X M
6 S
HC
SP
re /
50 in
-lbs
Not
e 1
1
2
3
Not
es:
Fast
ener
s sh
ippe
d lo
ose.
1.
Rev.
Des
crip
tion
Initi
ato
rD
ate
01In
itia
l Dra
win
g9/
23/1
32/
10/2
015
ITE
M N
O.
QTY
.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-S
MA
-843
7TS
M S
enso
r Mod
ule,
NP
N, 8
mm
Bar
rel
B2:
11
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 9/2
3/13
D. N
orto
n, 1
0/23
/13
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-S
MA-
8437
1305
10-5
01
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Sen
sor M
odul
e, N
PN, 8
mm
Bar
rel
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 83
3rd
AN
GLE
PRO
JEC
TION
27.
4
17.
8
8.9
19.
8
14.2
±0.0
7S
enso
r Dep
th
2X
3
10.
9 To
rque
jam
nut
to64
in-o
z
6.4
2X M
6 S
HC
SP
re /
50 in
-lbs
Not
e 1
1
2
3
Not
es:
Fast
ener
s sh
ippe
d lo
ose.
1.
Rev.
Des
crip
tion
Initi
ato
rD
ate
02EC
O 1
3538
; Cha
nged
torq
ue to
64
in-o
z (w
as 1
5 in
-oz)
SZJ
11/1
3/20
15
ITE
M N
O.Q
TY.P
AR
T N
UM
BE
RD
ES
CR
IPTI
ON
11
9120
-TS
M-S
MA
-843
9TS
M S
enso
r Mod
ule,
PN
P, 8
mm
Bar
rel
B2:
11
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
J. W
inte
rroth
, 2/1
8/15
D. N
orto
n, 2
/18/
15
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 96
30-2
0-TS
M-S
MA-
8439
1305
10-5
02
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Sen
sor M
odul
e, P
NP,
8m
m B
arre
l
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 84
3rd
AN
GLE
PRO
JEC
TION
63.5
44.5
31.8
44.5
32.3
19.1
31.8
50.8
(4)
7 Th
ru(4
) 7
Thru
9120-TSM
-SM-4206
9120-TSM
-SM-4205
M18
x 1
.0 T
hrea
dM
18 x
1.0
Thr
ead
NO
TES:
1. C
usto
mer
May
Spe
cify
Oth
er S
enso
rs.
P
art N
umbe
rs S
ubje
ct to
Cha
nge
5.1
5.1
Prox
Sen
sor
8590
-990
9999
-45
Efec
tor P
NP
IGS2
09
Oth
er S
enso
rsAv
aila
ble
Prox
Sen
sor
8590
-990
9999
-45
Efec
tor P
NP
IGS2
09
Oth
er S
enso
rs
Avai
labl
e
Rev.
Des
crip
tion
Initi
ator
Dat
e
01In
itial
Dra
win
gD
AN
8/27
/04
02Re
mov
e 91
20-T
SM-S
M-4
015
(Obs
olet
e)D
AW
5/5/
2015
B1:
11
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
Dan
Nor
ton,
8/2
7/04
D. W
agne
r 5/4
/15
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 92
30-2
0-19
0503
1217
-102
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
TSM
Sen
sor M
odul
es
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 85
9.37 Receiver Blocks
82.6
63.5
19.1
45
12.7
25.4
9.8
(2)
9 Th
ruFo
r M8
SH
CS
Har
dwar
e In
clud
ed
(2)
8mm
Thr
uD
owel
Slip
Fit
(Dow
el P
ins
Incl
uded
)NO
TES:
1. M
ATER
IAL:
414
0 H
arde
ned
Stee
l, Bl
ack
Oxi
de
Rev.
Des
crip
tion
Initi
ator
Dat
e
01In
itial
Dra
win
gD
AN
8/27
/04
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D
DO
NO
T SC
ALE
DRA
WIN
G.
DRA
WN
IN S
OLID
WO
RKS.
ALL
DIM
ENSI
ON
S A
RE IN
MILL
IMET
ERS.
3rd
AN
GLE
PRO
JEC
TION
DRA
WN
BY:
CHE
CKE
D B
Y:
WEI
GHT
LBS
:
ASS
EMBL
Y RE
F:
Dan
Nor
ton,
8/2
7/04
------
-----
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
DUC
T RE
LEA
SE #
DA
TE:
SHEE
T
OF
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C.
NO
T TO
BE
REPR
OD
UCED
IN A
NY
MA
NN
ER E
XCEP
T O
NO
RDER
OR
WITH
PRI
OR
WRI
TTEN
AUT
HORI
ZATIO
N O
F A
TI.
Gen
eral
Dim
ensi
ons
for T
SM-R
B-35
95
9230
-20-
1907
-01
B1:
21
1
------
-----
0312
17-1
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 86
9.38 Tooling Pins
37.5
17.9
0717
.780
18.5
34.3
12.7
12.0
4011
.913
96.5
18.2
6318
.136
12.7
96.2
12.7
12.3
7012
.243
M12
x 1
.75
Thre
ad
NO
TES:
M
ATER
IAL:
Sta
inle
ss S
teel
M10
x 1
.5 T
hrea
d
M12
x 1
.75
Thre
ad
M10
x 1
.5 T
hrea
d
10 H
EX
8 H
EX
25.4
19.1
3700-20-3590
3700-20-3594
3700-20-4017
3700-20-4016
Rev.
Des
crip
tion
Initi
ator
Dat
e
02A
dded
Vie
ws
DA
N8/
26/0
4
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D
DO
NO
T SC
ALE
DRA
WIN
G.
DRA
WN
IN S
OLID
WO
RKS.
ALL
DIM
ENSI
ON
S A
RE IN
MILL
IMET
ERS.
3rd
AN
GLE
PRO
JEC
TION
DRA
WN
BY:
CHE
CKE
D B
Y:
WEI
GHT
LBS
:
ASS
EMBL
Y RE
F:
Dan
Nor
ton,
8/2
3/04
------
-----
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
DUC
T RE
LEA
SE #
DA
TE:
SHEE
T
OF
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C.
NO
T TO
BE
REPR
OD
UCED
IN A
NY
MA
NN
ER E
XCEP
T O
NO
RDER
OR
WITH
PRI
OR
WRI
TTEN
AUT
HORI
ZATIO
N O
F A
TI.
TSM
Too
ling
Pins
9230
-20-
2041
-02
B1:
11
1
------
-----
0312
17-1
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 87
9.39 Medium Tool Stand General Overview
3rd
AN
GLE
PRO
JEC
TION
9120
-TSM
-MM
V-40
18TS
M M
ount
ing
Mod
ule,
V-B
lock
, Lar
ge(F
its R
ail H
oriz
onta
l Slo
ts,
or A
dapt
er M
odul
e)
9120
-TSM
-AM
-401
9Ad
apte
r Mod
ule
(Ada
pts
Mou
ntin
g M
odul
es to
R
ail E
nds,
Rai
l Ver
tical
Slo
ts)
9120
-TSM
-AM
-401
9Ad
apte
r Mod
ule
9120
-TSM
-PM
-331
8Po
st M
odul
e 48
" Tal
l
9120
-TSM
-HM
-332
3TS
M H
oriz
onta
l Mod
ule,
457
mm
(18"
)
9120
-TSM
-HM
-331
7TS
M H
oriz
onta
l Mod
ule,
914
mm
(36"
)
9120
-TSM
-MM
V-35
97TS
M M
ount
ing
Mod
ule,
V-B
lock
(Fits
Rai
l Hor
izon
tal S
lots
,or
Ada
pter
Mod
ule)
9120
-TSM
-HE-
3320
Hor
izon
tal E
xten
sion
6"
9120
-TSM
-HE-
3321
Hor
izon
tal E
xten
sion
10"
9120
-TSM
-HVQ
-405
9To
olin
g Pl
ate,
Q
C-1
00
9120
-TSM
-RB-
3595
Rec
ieve
r Blo
ck S
mal
l
9120
-TSM
-RB-
3591
Rec
ieve
r Blo
ck L
arge
Not
es:
Num
ber o
f Too
ls to
be
inst
alle
d pe
r Too
l siz
e sh
ould
be
conf
irmed
w
ith a
pplic
atio
n en
gine
erin
g pr
ior t
o sa
les
orde
r.
See
Not
e 1
Rev.
Des
crip
tion
Initi
ator
Dat
e
01In
itial
Dra
win
gD
AN
4/20
/04
02EC
O 9
908;
Rem
oved
slot
s on
Base
Pla
te.
JDB/
MSD
07/1
6/20
1203
ECO
116
40ER
DO
12/1
0/20
13
B1:
81
1RE
VISI
ON
NO
TES:
UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D.
DO
NO
T SC
ALE
DRA
WIN
G.
ALL
DIM
ENSI
ON
S A
RE IN
M
ILLIM
ETER
S.
DRA
WN
BY:
CHE
CKE
D B
Y:
Dan
Nor
ton
4/20
/04
JWin
terro
th 1
0/11
/12
TITLE SC
ALE
SIZE
DRA
WIN
G N
UMBE
R
PRO
JEC
T #
SHEE
T
O
F 92
30-2
0-18
8003
1217
-103
PRO
PERT
Y O
F A
TI IN
DUS
TRIA
L A
UTO
MA
TION
, IN
C. N
OT
TO B
E RE
PRO
DUC
ED IN
AN
Y M
AN
NER
EXC
EPT
ON
ORD
ER O
R W
ITH P
RIO
R W
RITT
EN A
UTHO
RIZA
TION
OF
ATI.
1031
Goo
dwor
th Dr
ive, A
pex,
NC 27
539,
USA
Tel: +
1.919
.772.0
115
Em
ail: in
fo@ati
-ia.co
mFa
x: +1
.919.7
72.82
59
www
.ati-ia
.com
ISO
9001
Reg
ister
ed C
ompa
ny
Med
ium
Too
l Sta
nd G
ener
al O
verv
iew
Manual, Tool Stand, TSMDocument #9610-20-1114-10
Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 88
10. Terms and Conditions of SaleThe following Terms and Conditions are a supplement to and include a portion of ATI’s Standard Terms and Conditions, which are on file at ATI and available upon request.
ATI warrants to Purchaser that robotic Tool Changer products purchased hereunder will be free from defects in material and workmanship under normal use for a period of three (3) years from the date of shipment. This warranty does not cover components subject to wear and tear under normal usage or those requiring periodic replacement. ATI will have no liability under this warranty unless: (a) ATI is given written notice of the claimed defect and a Description thereof within thirty (30) days after Purchaser discovers the defect and in any event not later than the last day of the warranty period; and (b) the defective item is received by ATI not later ten (10) days after the last day of the warranty period. ATI’s entire liability and Purchaser’s sole remedy under this warranty is limited to repair or replacement, at ATI’s election, of the defective part or item or, at ATI’s election, refund of the price paid for the item. The foregoing warranty does not apply to any defect or failure resulting from improper installation, operation, maintenance or repair by anyone other than ATI.
ATI will in no event be liable for incidental, consequential or special damages of any kind, even if ATI has been advised of the possibility of such damages. ATI’s aggregate liability will in no event exceed the amount paid by purchaser for the item which is the subject of claim or dispute. ATI will have no liability of any kind for failure of any equipment or other items not supplied by ATI.
No action against ATI, regardless of form, arising out of or in any way connected with products or services supplied hereunder may be brought more than one (1) year after the cause of action accrued.
No representation or agreement varying or extending the warranty and limitation of remedy provisions contained herein is authorized by ATI, and may not be relied upon as having been authorized by ATI, unless in writing and signed by an executive officer of ATI.
Unless otherwise agreed in writing by ATI, all designs, drawings, data, inventions, software and other technology made or developed by ATI in the course of providing products and services hereunder, and all rights therein under any patent, copyright or other law protecting intellectual property, shall be and remain ATI’s property. The sale of products or services hereunder does not convey any express or implied license under any patent, copyright or other intellectual property right owned or controlled by ATI, whether relating to the products sold or any other matter except for the license expressly granted below.
In the course of supplying products and services hereunder, ATI may provide or disclose to Purchaser confidential and proprietary information of ATI relating to the design, operation or other aspects of ATI’s products. As between ATI and Purchaser, ownership of such information, including without limitation any computer software provided to Purchaser by ATI, shall remain in ATI and such information is licensed to Purchaser only for Purchaser’s use in operating the products supplied by ATI hereunder in Purchaser’s internal business operations.
Without ATI’s prior written permission, Purchaser will not use such information for any other purpose or provide or otherwise make such information available to any third party. Purchaser agrees to take all reasonable precautions to prevent any unauthorized use or disclosure of such information.
Purchaser will not be liable hereunder with respect to disclosure or use of information which: (a) is in the public domain when received from ATI; (b) is thereafter published or otherwise enters the public domain through no fault of Purchaser; (c) is in Purchaser’s possession prior to receipt from ATI; (d) is lawfully obtained by Purchaser from a third party entitled to disclose it; or (f) is required to be disclosed by judicial order or other governmental authority, provided that, with respect to such required disclosures, Purchaser gives ATI prior notice thereof and uses all legally available means to maintain the confidentiality of such information.