Post on 13-Dec-2015
description
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
3 First Configuration : Configuration Wizard
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Presentation
The aim of configuration wizard is to have a Network Element fully configured within a few steps.
This configuration wizard is almost common to TCO suite and Quick Configuration via CT-K
The screen copies will be the one of TCO suite, PreProvisionning Tool (PPT).
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 1 : NE Type
NE name as it will appear on mapNE location as it will appear on map
Letting these fields empty some applications do not work properly
Protection Type
User Interface Type
Optional Audio – ESC Plug-in
(N/A in R2.1) Audio Party Line can not be set up through configuration wizard
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 1 (continued) : Aggregate structure
Capacity of aggregate signal
Modulation scheme of ODU
Capacity 2 E1 4 E1 8 E1 16 E1 32 E1 Modulation Choice 4 QAM only 4 / 16 QAM 4 / 16 QAM 4 / 16 QAM 16 QAM only
Modulation agility is neither available for 2 E1 (4 QAM only) nor for 32 E1 (16 QAM only) due to spectrum width used in these radios.
Capacity and modulation choices are available depending on the Licence Key located inside the flash card. Limitations in combo boxes do not apply in the wizard.
Note for 16 E1 – Data NE :
capacity is the one of the aggregate signal. 32 E1 capacity may be used for a full Ethernet traffic.
In this last case, only the first 16 E1 are manageable (no physical presence of other E1 on front pannel)
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 2 : User line interface, PDH
One shot buttons
Combo box to set up E1 port modeTributary impedance
(75 or 120 ohms) Greyed because not settable, depending on NE type and capacity
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 2 (continued) : User line interface, Data
Speed to be set upEnable / Disable Ethernet port
This tab will appear only in 16 E1 – Data configuration
Bug : Autonegociation should be set at the end of commissionning, it is equivalent to a command and not to a configuration parameter
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 2 (continued and finish) : User line interface, Data FCS
This tab will appear only in 16 E1 – Data configuration
Discard errored frames depends highly on the customer applications.
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 3 : RT parameters configuration
Pushing the Frequency Data Help will display informations related to ODUs
ATPC parameters should be set at the end of commissionning
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 4 : Link Identifier
Link Identifier is coming back !
In case of Link Identifier Mismatch alarm, signal is sent anyway (Melodie behavior was to generate an AIS)
Bug : If Expected Identifier is equal to Sent Identifier, no alarm is raised.
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 5 : Restoration criteria
This configuration is recommanded, except in case of Data transmission NE
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 6 : OSPF Areas configuration
Add the relevant OSPF area(s). Generally, only one is declared other than ospf 0.
Bug : If you are modifying a file, add an ospf area instead of removing / add
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 7 : Local configuration
Default configuration on Eth/OS is 10.0.1.2 / 255.0.0.0. This has to be reminded when the operator sends a first configuration using Eth/OS interface (communication between PC and Equipement will be lost if this is modified).
Bug : Put the same address for NTP Spare Server even if there is only one server.
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 8 : PPP interfaces
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 9 : Static Routes
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 10 : I/O
"Bug" : Java behavior : for a field to be taken into account, the operator has to fill in the information and to click somewhere else in the page.
"Bug" : It is not so obvious, but polarity can be set up (active opened / active closed)
9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007
Configuration Wizard
Step 11 : Configuration summary
"Finish" button available from JUSM.
"Save and Apply" available from SUT.