Post on 13-Jan-2017
KVH
Indu
stries
, Inc.
Installation Guide
TracVision® TV5
TracVision TV5 Installation Guide
1
KVH, TracVision, and the unique light-colored dome with dark contrasting baseplate are registered trademarks of
KVH Industries, Inc. All other trademarks are property of their respective companies. The information in this document is subject
to change without notice. No company shall be liable for errors contained herein. © 2014-2015 KVH Industries, Inc.,
All rights reserved. 54-0983 Rev. C
This guide explains how to install the TracVision TV5 satellite TV antenna system on a vessel. Operation instructions are provided in the Quick Start Guide.
Installation Steps
Appendices
Who Should Install the System?To ensure a safe and effective installation, KVH recommends that a KVH-authorized marine technician install the TracVision antenna. KVH-authorized technicians have the tools and electronics expertise necessary to install the system. To find a technician near you, visit www.kvh.com/wheretogetservice.
Technical SupportIf you need technical assistance, please contact KVH Technical Support:
1. Inspect Parts and Get Tools ..................3
2. Plan the Antenna Installation...............4
3. Plan the TV-Hub Installation................5
4. Prepare the Antenna Site.......................6
5. Prepare the RF Cables............................7
6. Wire the Antenna ...................................8
7. Remove the Shipping Restraints ..........9
8. Mount the Antenna..............................10
9. Mount the TV-Hub...............................11
10. Wire the Antenna to the TV-Hub.......12
11. Wire the Receivers................................13
12. Connect a NMEA Device ....................22
13. Connect Power......................................23
14. Turn On the System .............................25
15. Access the Web Interface.....................26
16. Connect to an Onboard Network.......27
17. Secure the Wi-Fi Connection ..............28
18. Set Up the System.................................29
19. Set the LNB Skew Angle .....................32
20. Educate the Customer..........................33
A. Installing an IP AutoSwitch................34 B. Using a DIRECTV Coax Network......38
Europe, Middle East, Africa, Asia-PacificPhone: +45 45 160 180Email: support@emea.kvh.com(Mon.-Thu., 8 am-4:30 pm; Fri., 8 am-2 pm, +1 GMT)
North/South America, AustralasiaPhone: +1 401 847-3327Email: support@kvh.com(Mon.-Fri., 9 am-6 pm; Sat., 9 am-2 pm ET, -5 GMT)
2
This icon indicates a danger, warning, or caution notice. Be sure to read these carefully to avoid injury.
WARNING
Risk of Electric ShockTo avoid electric shock, do not open the TV-Hub chassis enclosure. There are no user-serviceable parts inside.
WARNING
Risk of Electric ShockIf any component of the TracVision system becomes damaged and/or no longer functions normally, disconnect it from vessel power, secure it from unintended operation, and contact KVH Technical Support (see “Technical Support” on page 1). All repairs or modifications must be performed by a trained, KVH-certified technician. If you are a KVH-certified technician, you still must contact KVH Technical Support prior to conducting any repairs or modifications to the equipment.
WARNING
Risk of ExplosionDo not operate the TV-Hub (or any other electrical device) in an environment where flammable gases, vapors, or dusts are present. In addition, do not operate the TV-Hub in an environment with a temperature outside its 5º F to 131º F (-15º C to 55º C) temperature range.
WARNING
Risk of Electric ShockFailure to ground the TracVision system properly to ship’s ground will cause an unsafe floating ground condition, risking potentially lethal electric shock. See “Connect Power” on page 23 for details on the proper grounding of the equipment.
Important Safety Information
3
Antenna
TV-Hub
Radome
Baseplate
Figure 1: TracVision TV5 System Components
Figure 2: KVH-Validated Receivers
* List is subject to change. For information on connecting different receiver models, contact KVH Technical Support.
Linear
For information on the recommended receivers for linear service, contact your local KVH dealer/distributor. Go to www.kvh.com/wheretogetservice to find a dealer/distributor near you.
DIRECTV* DISH Network*
H20H21H22H23H24H25HR21, HR21 ProHR22HR23HR24HR34HR44
311211211k211z
Bell TV*
610061316400
Inspect Parts and Get Tools1
Before you begin, follow these steps to ensure you have everything needed to complete the installation.a. Unpack the box and ensure it contains everything shown on the Kitpack Contents List. Save the packaging for future use.
b. Carefully examine all of the supplied parts to ensure nothing was damaged in shipment.
c. Gather the tools and materials listed below. You will need these items to complete the installation.
• Flat-head and Phillips-head screwdrivers
• Electric drill and 3/8" (10 mm) and 1/8" (3 mm) drill bits
• 3" (80 mm) hole saw
• Socket wrenches
• 7/16" open-end torque wrenches set to 20 in.-lbs (2.25 N-m) and 15 in.-lbs (1.7 N-m)
• Torque wrench and 2 mm Allen hex key (linear manual skew system only)
• Light hammer and center punch
• Adhesive tape and scriber or pencil
• RG-6 or RG-11 RF coax cable(s), with “F” connectors, and termination tools (see page 7)
• Silicone sealant or equivalent
• Satellite TV receiver(s)/DVRs for your desired service (see Figure 2)
• Wi-Fi-enabled laptop PC with the latest TracVision software and satellite library downloaded from the KVH Partner Portal (www.kvh.com/partners), or Apple® iOS or Android™ smartphone/tablet with the latest downloads via the TracVision TV/RV mobile app
Always lift the antenna by the baseplate and never by the radome or any portion of the internal antenna assembly (see Figure 1).
IMPORTANT!
4
Blocked!
TracVision Antenna
Mast
Look Angle
Vessel Platform
0° to 80°
Figure 3: Blockage from Obstruction
Figure 4: Distance from Radar
+15°
-15°
3 ft (1 m)
Minimum
Radar Potential RFInterference
20.9"(53.2 cm)
Ø 19.2"(Ø 48.8 cm)
Side View
Bottom View9.0"(22.9 cm)
4 x Ø 0.31"(Ø 0.8 cm)
4.5"(11.4 cm)
Figure 5: Antenna Dimensions
Plan the Antenna Installation
Before you begin, consider the following antenna installation guidelines.• Minimize blockage. The antenna requires a clear view of the sky to receive satellite TV (see Figure 3). The fewer obstructions, the better the system will perform.
• Consider the distance between your antenna and any radar. KVH requires that you do not mount the antenna on the same level as the radar, because the radar’s energy may damage the LNB. Most radar transmitters emit RF energy within an elevation range of -15º to +15º (see Figure 4). Therefore, mount the antenna outside of this elevation range and at least 3 ft (1 m) away from the radar.
• Make sure the mounting surface is wide enough to accommodate the antenna’s base (see Figure 5). Also make sure it is flat, level (within ±1°), strong enough to support the antenna’s weight, and rigid enough to prevent antenna vibration.
• Select a location that is as close as possible to the intersection of the vessel’s fore-and-aft centerline and midships.
• Be sure to mount the antenna near enough to the TV-Hub to allow you to connect the 100 ft (30 m) coax cable between them, while still maintaining sufficient slack in the cable.
NOTE: If you need to use a longer cable, use a RG-11 (75 ) cable that does not exceed 200 ft (60 m) in length (see “Prepare the RF Cables” on page 7).
Be sure to follow the guidelines below. Damage caused by an improper installation is not covered under KVH warranty.
IMPORTANT!
Never place the antenna in the beam path of the radar, regardless of distance. The radar’s energy may damage the antenna or impair its performance.
IMPORTANT!
2
5
1.73"(4.4 cm)
9.34"(23.7 cm)
4.36"(11.1 cm)
7.90"(20.0 cm)
LED Lights
Figure 6: TV-Hub Dimensions - Horizontal Orientation
Top View9.34"(23.7 cm)
10.94"(27.8 cm)
10.52"(26.7 cm)
7.90"(20.0 cm)
LED Lights
Figure 7: TV-Hub Dimensions - Vertical Orientation
Plan the TV-Hub Installation
Consider the following TV-Hub installation guidelines.• Select a mounting location in a dry, well-ventilated area belowdecks away from any heat sources or salt spray.
• Do not install the TV-Hub in an area surrounded by metal or near any electrical devices that emit RF noise.
• The TV-Hub can be mounted horizontally or vertically on a flat surface (see Figure 6 and Figure 7).
• Be sure the TV-Hub LED lights will be visible to the user.
• Select a location that will provide adequate clearance for the TV-Hub dimensions (see Figure 6 and Figure 7).
• Leave enough room behind the rear panel (horizontal mount) or below the rear panel (vertical mount) to accommodate connecting the cables and making service loops within the proper bend radius.
• If you plan to use the TV-Hub’s Wi-Fi connections, ensure the TV-Hub mounting location provides adequate Wi-Fi reception.
• If you plan to connect the TV-Hub to the vessel’s onboard local area network (LAN), choose a location near an available Ethernet port.
NOTE: A template showing the exact locations of the TV-Hub mounting holes and the dimensions between them is provided in the Welcome Kit. Installation details are provided in “Mount the TV-Hub” on page 11.
3
6
9"(229 mm)Ø 3/8" (Ø 10 mm)
Mounting Hole (x4)
Ø 3.5" (Ø 89 mm)Cable Access Hole
FWD
Align Foam Sealwith Cable
Access Hole
9"(229 mm)
Figure 8: Antenna Mounting Holes Layout
Prepare the Antenna Site
Once you have identified a suitable antenna mounting site, according to the guidelines provided on page 4, follow these steps to drill the mounting holes and cable access hole to prepare the site for installation.a. Unfold the antenna mounting template (supplied in the Customer Welcome Kit) and place it onto the mounting surface. Make sure the “FWD” (forward) arrow points toward the bow and is parallel to the vessel’s centerline (see Figure 8). Tape in place.
NOTE: You don’t need to mount the antenna exactly on the vessel’s centerline (the closer, the better), but the antenna’s forward arrow must be parallel to it.
b. Using a light hammer and center punch, mark the locations for the four mounting holes and cable access hole on the mounting surface in the locations indicated on the template.
c. Drill a 3/8" (10 mm) hole at the four mounting hole locations you marked in Step b. Later, you will insert four 1/4"-20 bolts through these holes to secure the antenna to the mounting surface.
d. Cut out the 3" (80 mm) cable access hole in the location you marked in Step b. Smooth the edges of the hole to protect the cables. Later, you will route the RF cable(s) through this hole and into the vessel.
e. Clean and dry the antenna mounting surface.
f. Peel off the paper backing from the supplied foam seal to expose the adhesive. Then press the foam seal down firmly onto the mounting surface, ensuring the hole in the foam seal aligns with the cable access hole in the mounting surface (see Figure 8).
NOTE: Apply the foam seal to the vessel mounting surface, not to the antenna’s baseplate. You will have difficulty connecting the cable(s) to the antenna if the foam seal is attached to the baseplate.
4
7
Note: LMR-400-75 is a suitable substitute.
Up to 100 ft (30 m) Cable Run
Cable RG-6(KVH part no. 32-0417-0100)
Connector Thomas & Betts SNS1P6(KVH part no. 23-0170)
Tools Augat IT1000(KVH part no. 19-0242)
Strip Lengths
Up to 200 ft (60 m) Cable Run
Cable RG-11(KVH part no. 32-1272-0200)
Connector Thomas & Betts SNS11AS(KVH part no. 23-0213)
Tools Thomas & Betts CST596711,L3011B (KVH part no. 72-0493)
Strip Lengths
0.25" (6.35 mm)0.5" (12.7 mm)
0.064" (1.63 mm) dia.
0.25" (6.35 mm)0.5" (12.7 mm)
0.064" (1.63 mm) dia.
Figure 9: RF Cable Requirements
Prepare the RF Cables
Determine the necessary type of RF cable(s) and connectors you need for any RF cables that are required in addition to what is supplied in the antenna kit (see Figure 9 and Figure 10 on page 8). Then follow the guidelines below to prepare the cable(s).• Do not reuse old RF cables from a previous antenna installation. The RF1 cable between the TV-Hub and the antenna carries not only satellite signal, but power and data as well. Therefore, the integrity and reliability of this cable is critically important.
• RF cables must be rated for 75not 50
• Use of any cables not specified in Figure 9 will void the warranty.
• Low-quality, poorly terminated, or improperly installed RF cables are the most common cause of system problems. Terminate all RF cables with high-quality “F” connectors using the proper stripping/crimping tools, exactly to the manufacturer’s specifications.
• When determining cable lengths, be sure to account for an adequate service loop, approximately 8" (20 cm) at both ends of each cable.
IMPORTANT!
5
8
Figure 10: Number of RF Coax Cables to Connect to Antenna
* Multiswitch may be required.
Connecting to: RF Cables
System with Circular LNB
1 receiver 1
2 or more receivers 1*
System with Tri-Americas Circular LNB
2 or more receivers 2*
System with DIRECTV L.A. Circular LNB
1 receiver 1
2 or more receivers 2*
System with Linear Universal Quad LNB
1 receiver 1
2 receivers 2
3 receivers 3
4 receivers 4
More than 4 receivers 4*
RF2
RF1
RF3
RF4
FWD
Figure 11: Connectors on Bottom of Antenna
Wire the Antenna
Follow the steps below to connect the antenna cable(s) to the antenna.a. First determine the number of RF coax cables you need for your installation (see Figure 10).
b. Clearly label the RF1 cable at both ends. If you connect two or more RF cables, label both ends of each cable to match the connector. This will make it easier to identify the cables.
c. Route the RF cable(s) belowdecks through the 3" (80 mm) cable access hole. Leave an adequate service loop (8" (20 cm) of slack) in the cables for serviceability.
d. Clean and dry the connectors on the RF cable(s) and the antenna (see Figure 11).
e. Fill half of the inner body of the RF1 cable’s connector with the supplied silicone grease.
f. Connect and SLOWLY hand-tighten the RF1 cable to the “RF1” connector on the bottom of the antenna, allowing the grease to diffuse and settle into the entire space within the connector.
g. Make sure the RF cable is hand-tightened all the way into the connector. Then tighten it with a 7/16" torque wrench to 20 in-lbs, or a 7/16" wrench for 1/4 turn.
h. Wipe off any excess grease from the outside of the connector.
i. Repeat steps d-h to connect any additional RF cables to the antenna’s RF2, RF3, and RF4 connectors. Later, you will connect the RF1 cable to the TV-Hub and any other RF cable(s) to a grounding block and receiver(s).
j. Seal the RF cable connections with silicone sealant or equivalent.
k. Weatherproof and seal the cable access hole as required.
CAUTION
Observe the safe handling instructions in the Material Safety Data Sheet (MSDS) provided with the silicone grease.
6
9
#10-32 Screw (x4)
Figure 12: Removing the Radome
Bolt
Washer
Tag
Spacer
Foam Block
Figure 13: Shipping Restraints
Remove the Shipping Restraints
Inside the antenna, shipping restraints prevent the antenna assembly from moving during shipment. Follow these steps to remove these shipping restraints.a. Remove the four #10-32 Phillips screws securing the radome to the baseplate (see Figure 12). Carefully lift the radome straight up until clear of the antenna assembly and set it aside in a safe place.
If you keep the radome topside, secure it with a lanyard to prevent it from falling overboard. Also, do not place the radome on a hot steel deck – the heat may warp the radome.
b. Remove the foam block that is wedged beneath the antenna’s reflector (see Figure 13).
c. Using a 10 mm socket wrench, remove the bolt, washer, tag, and spacer securing the antenna assembly to the baseplate (see Figure 13).
NOTE: Save the restraints for future use; the restraints will need to be reinstalled if the customer needs to relocate or reship the antenna.
Once you have removed the restraints, keep the antenna level as much as possible and handle the antenna carefully. Prevent the internal antenna assembly from rotating freely within the baseplate to avoid damaging the limit switch.
IMPORTANT!
7
1
B
Figure 14: Overhead View of Forward Arrow in Antenna Baseplate
1/4"-20 x 3" Bolt (x4)
1/4" Flat Washer (x4)
Foam Seal
Mounting Surface
1/4" Flat Washer (x4)
1/4"-20 Lock Nut (x4)
Antenna Base
IMPORTANT: Apply anti-seize to threads
Figure 15: Mounting the Antenna (Side View)
Mount the Antenna
Follow these steps to mount the antenna.a. Place the antenna over the holes drilled in the mounting surface. Ensure the forward arrow points toward the bow and is parallel to the vessel’s centerline (see Figure 14).
b. Apply a thin layer of the supplied anti-seize lubricant to the threads of the four 1/4"-20 mounting bolts (see Figure 15).
c. At each of the four baseplate mounting holes, place a 1/4" flat washer on a 1/4"-20 bolt and insert the bolt into the hole from above (see Figure 15).
d. Secure each mounting bolt to the mounting surface using a 1/4" flat washer and a 1/4"-20 lock nut from below. Tighten all four bolts until the four rubber feet on the baseplate are bottomed against the mounting surface and the foam seal is fully compressed.
e. Reinstall the radome onto the antenna. Secure in place with the four #10-32 screws you removed on page 9. Hide and protect the screws with the plastic screw caps (supplied in the kit).
CAUTION
Be sure to observe the safe handling instructions in the Material Safety Data Sheet (MSDS) provided with the anti-seize lubricant.
You will need to rotate the antenna assembly by hand to see all four mounting holes. Rotate it slowly to avoid damaging the limit switch.
IMPORTANT!
8
0
11
7.93"(20.1 cm)
3.17"(8.1 cm)
4.86"(12.3 cm)
Front of TV-Hub
Keyhole2 x Ø 0.13"(Ø 0.3 cm)
Mounting TabØ 0.13"(Ø 0.3 cm)
Figure 16: TV-Hub Mounting Template
Keyhole (x2)
Mounting Tab
Figure 17: TV-Hub Keyholes and Mounting Tab
Mount the TV-Hub
Follow these steps to install the TV-Hub inside the vessel.a. Tape the mounting template in the location selected for the TV-Hub. Punch holes at each of the two keyhole locations and at the mounting tab location.
b. Remove the template.
c. Drill a 1/8" (3 mm) hole at the three hole locations you marked in Step a.
d. Install a #8 Phillips thread-forming screw partway into one of the keyhole holes leaving a small gap for hooking the TV-Hub onto it. Use the thickness (2.5 mm) of the M10 washer (supplied in the kit) as a gauge for the size gap to leave.
e. Repeat step d on the other keyhole.
f. Peel off the backing on the adhesive-backed washer (supplied in the kit) and place it over the mounting tab hole (see Figure 16).
g. Align the wide part of the TV-Hub’s keyholes, as shown in Figure 17, over the screws, then slide downwards to secure the screws into the narrow part of the keyholes.
h. Press the rear mounting tab of the TV-Hub onto the adhesive washer and install the third #8 Phillips thread-forming screw in the mounting tab hole.
9
1
Deck
AntennaTo antenna only,supplies 42 VDC
RF1
Figure 18: TV-Hub Antenna Connection
Wire the Antenna to the TV-Hub
2
Follow these steps to connect the antenna to the TV-Hub.
a. Connect the RF1 cable from the antenna to the “Antenna” jack on the TV-Hub (see Figure 18).
b. Hand-tighten the RF cable until it is all the way into the “Antenna” jack. Then tighten it with a 7/16" torque wrench to 15 in-lbs, or a 7/16" wrench 1/8 turn.
Do not connect anything other than the antenna’s RF1 cable to the “Antenna” jack. The “Antenna” jack has 42 VDC on it which will damage other devices, such as multiswitches, DVRs, etc.
IMPORTANT!
10
13
TV-Hub A
DIRECTV U.S. Non-SWM Receivers
DISH Network, Bell TVand Linear Receivers
DIRECTV U.S.SWM Receivers
Figure 19: TV-Hub A Receiver Connections
TV-Hub B
Linear, Tri-Americas, andDIRECTV Latin America Receivers
Figure 20: TV-Hub B Receiver Connections
Wire the Receivers
The steps for connecting the customer’s receiver(s) to the TracVision system and setting them up depends upon the customer’s satellite TV service (see Figure 19 and Figure 20).NOTE: KVH’s TracVision Configuration Wizard, available at www.kvh.com/tvseriesconfigurator, displays a wiring diagram and parts list for all of the most common configurations.
Follow the steps in the applicable section below to wire the receivers. Then connect the receiver(s) to the customer’s television(s).
Linear. . . . . . . . . . . . . . . . . . . . . . . . page 14
DIRECTV (SWM) . . . . . . . . . . . . . . page 16
DIRECTV (Non-SWM) . . . . . . . . . page 18
DIRECTV Latin America . . . . . . . page 19
Tri-Americas . . . . . . . . . . . . . . . . . . page 20
DISH Network/Bell TV . . . . . . . . page 21
11
1
Figure 21: Wiring 1 Linear Receiver
TV-Hub
Antenna
Receiver
AC PowerSatellite In
Receiver
RF1
TV-Hub
Antenna
Receiver
AC PowerSatellite In
Receiver
RF1
Receiver
AC Power
Satellite In
Receiver
AC Power
Satellite In
Receiver
AC Power
Satellite In
RF4RF3RF2
GroundingBlocks
Figure 22: Wiring 2 to 4 Linear Receivers
Continued Wire the Receivers
4
Linear WiringFollow these steps to connect linear receivers to the TracVision system (linear universal quad LNB required).
Connecting 1-4 Linear Receivers a. Connect an RF cable from the “Receiver” jack
on the TV-Hub to the “Satellite In” jack on the first receiver (see Figure 21). This receiver will be able to control satellite selection in Automatic satellite switching mode.
b. When connecting multiple receivers, connect a grounding block in-line with each RF cable from the antenna (see Figure 22 and “Grounding Requirements” on page 23).
c. Connect the other end of the RF1 cable to the “Antenna” jack on the TV-Hub.
d. Connect any other RF cables from the antenna (RF2, RF3, and RF4) to the “Satellite In” jack on each additional receiver (see Figure 22).
To enable any of the additional receivers to control satellite selection, install an optional IP AutoSwitch (KVH part no. 72-0634) in-line with the receiver’s RF input. See Appendix A on page 34 for details.
IMPORTANT!
11
15
Figure 23: Wiring 5+ Linear Receivers
Continued Wire the Receivers
TV-Hub
AntennaReceiver
RF1 RF4RF3RF2
Receiver
AC Power
Satellite In
Connect up to 8 receivers
18V
13V13V/22KHz
18V/22KHz
AC Power
13V 18V/22KHz
13V/22KHz
18V
Multiswitch
GroundingBlocks
Connecting 5 or More Linear Receiversa. Connect an RF cable from the “Receiver” jack
on the TV-Hub to the “18V” jack on the multiswitch (see Figure 23).
NOTE: If the desired satellite TV service is limited to channels carried on high-band transponders (for example, Sky Mexico), connect the RF cable from the TV-Hub to one of the “22KHz” tone inputs on the multiswitch, instead of the “18V” input. In addition, since you do not need the “18V” and “13V” inputs for high-band transponders, you only need to connect the RF1 and RF2 cables to the multiswitch; RF3 and RF4 are unnecessary.
b. Connect a grounding block in-line with each RF cable from the antenna (see Figure 23 and “Grounding Requirements” on page 23).
c. Connect the other end of the RF1 cable to the “Antenna” jack on the TV-Hub.
d. Connect the RF2, RF3, and RF4 cables to the multiswitch, as shown in Figure 23.
e. Connect each multiswitch output to the “Satellite In” jack on each receiver.
f. Terminate any unused outputs on the multiswitch with 75terminators and verify all connections are tight.
To enable any of the receivers to control satellite selection, install an optional IP AutoSwitch (KVH part no. 72-0634) in-line with the receiver’s RF input. See Appendix A on page 34 for details.
IMPORTANT!
11
1
Figure 24: Wiring 1 DIRECTV SWM Receiver
TV-Hub
AC Power
SWM Receiver
Satellite In
Antenna
RF1
SWM
Figure 25: Wiring a DIRECTV SWM Splitter
TV-HubSWM
RAUDIO OUT
L
PrPbY
VIDEO OUT S-VIDEO OUT
DIGITALAUDIO OUT
ETHERNET
SATELLITE IN 1
IR RECEIVE SATA HDMI PHONE JACK
POWER INPUT
USB
COMPONENT VIDEO OUT
Genie DVR
Genie Client
Genie Client
Genie Client
Network
Network
Network
Satellite In
Note: Although you may connectadditional Genie clients, only 3 can beactive at one time
AC Power
AC Power
SWM DVRAC Power
SWM ReceiverSatellite In
Satellite In
Supports up to 8 tuners:Each SWM receiver = 1 tunerEach SWM DVR = 2 tunersEach Genie DVR = 5 tunersEach Genie client = 0 tuners SWM Splitter
Terminateunusedoutputs
Continued Wire the Receivers
6
DIRECTV – SWM WiringFollow these steps to connect DIRECTV SWM receivers to the TracVision system (circular LNB and TV-Hub A required).
NOTE: You can connect non-SWM receivers as well, as explained in “DIRECTV – Non-SWM Wiring” on page 18.
Connecting 1 SWM ReceiverConnect an RF cable from the “SWM” jack on the TV-Hub to the “Satellite In” jack on the receiver/DVR (see Figure 24).
Connecting 2-8 SWM Receivers (or Tuners)a. Connect an RF cable from the “SWM” jack on
the TV-Hub to the “SWM” input on the SWM splitter (supplied in the kit) (see Figure 25).
b. Connect the SWM splitter’s outputs to the “Satellite In” jack on the receivers/DVRs (or “Network” jack when connecting a Genie client). You can connect any number of SWM and Genie devices that add up to 8 tuners or fewer. Refer to Figure 25 to determine the tuners consumed by each type of device.
c. Terminate any unused outputs on the SWM splitter with the supplied 75terminators and verify all connections are tight.
If you need to receive local channels on the 119W satellite, and you want the antenna to automatically switch between the 101W and 119W satellites, you need to use the DIRECTV coax network. See Appendix B on page 38 for details.
IMPORTANT!
11
17
Figure 26: Wiring a DIRECTV External SWM-8 Kit
TV-Hub
Antenna Antenna
AC Power
SWM
18V
13V 18V/22KHz
13V/22KHz
DC BlockSplitter
DC BlockSplitter
Secondary Primary Secondary Primary
SWM PowerInserter SWM-8
ModuleSWM1/PWR
AC Power
SWM Receiver/DVRSatellite In
Connect any combination of SWM receivers/DVRsthat add up to 8 or fewer tuners at the SWM splitter
SWM Splitter
Terminateunusedoutputs
Supports up to 8 tuners:Each SWM receiver = 1 tunerEach SWM DVR = 2 tuners
IRD
Legacy 2Legacy 1
Continued Wire the Receivers
Connecting 9-16 SWM Receivers (or Tuners)To connect more than 8 tuners, first follow the steps for 2-8 tuners, as explained on the previous page. Then install an external SWM-8 kit (KVH part no. 72-0678). Connect the kit to the “Legacy” jacks on the TV-Hub then connect the SWM devices, as shown in Figure 26.If you need to receive local channels on the 119W satellite, and you want the antenna to automatically switch between the 101W and 119W satellites, you need to use the DIRECTV coax network. See Appendix B on page 38 for details.
IMPORTANT!
11
1
TV-Hub
Non-SWM Receiver
AC PowerSatellite In
Non-SWM Receiver
AC PowerSatellite In
Legacy 2Legacy 1
Antenna
RF1
Figure 27: Wiring 1 to 2 DIRECTV Non-SWM Receivers
Figure 28: Wiring 3+ DIRECTV Non-SWM Receivers
Non-SWM Receiver
AC Power
Satellite In
TV-Hub
Connect up to 8 non-SWM receivers
13V/22KHz
13V18V
18V/22KHz
DC BlockSplitter
DC BlockSplitter
Antenna Antenna
AC Power
13V 18V/22KHz
13V/22KHz
18V
Multiswitch
Legacy 2Legacy 1
Secondary Primary Secondary Primary
Continued Wire the Receivers
DIRECTV – Non-SWM WiringFollow these steps to connect non-SWM receivers to the TracVision system (circular LNB and TV-Hub A required).
NOTE: You can connect SWM receivers as well, as explained in “DIRECTV – SWM Wiring” on page 16.
Connecting 1-2 Receiversa. Connect an RF cable from the “Legacy 1” jack
on the TV-Hub to the “Satellite In” jack on the receiver (see Figure 27).
b. When installing two receivers, connect an RF cable from the “Legacy 2” jack on the TV-Hub to the “Satellite In” jack on the second receiver.
Connecting 3 or More ReceiversTo connect three or more non-SWM receivers, you need an 8-output multiswitch kit (KVH part no. 72-0677), which includes two DC block splitters.
a. Connect an RF cable from the “Legacy 1” jack on the TV-Hub to the “Antenna” jack on one of the DC block splitters (see Figure 28).
b. Connect the “Primary” jack on the DC block splitter to the “18V” jack on the multiswitch, and connect the “Secondary” jack on the DC block splitter to the “18V/22KHz” jack on the multiswitch.
c. Repeat steps a and b with “Legacy 2” and the second DC block splitter using the “13V” and “13V/22KHz” jacks on the multiswitch.
d. Connect the multiswitch outputs to the “Satellite In” jacks on the non-SWM receivers.
e. Terminate any unused outputs on the multiswitch with 75terminators and verify all connections are tight.
Non-SWM receivers are limited to manual satellite switching only.
IMPORTANT!
11
8
19
TV-Hub
AC Power
DIRECTV L.A. Receiver
Satellite In
ReceiverAntenna
RF1
Figure 29: Wiring 1 DIRECTV Latin America Receiver
Figure 30: Wiring Multiple DIRECTV Latin America Receivers
TV-Hub
PowerInserter
Connect up to 4 receivers
Terminateunusedoutputs
GroundingBlock
Receiver
Antenna
AC PowerSatellite In
18V13V
RF1 RF2
13VV-OUT
AC Power
DIRECTV L.A. Receiver
13V18V
Multiswitch
Set switch to:17/18V-HORZ.13/14V-VERT.
Continued Wire the Receivers
DIRECTV Latin America WiringFollow these steps to connect DIRECTV Latin America receivers to the TracVision system (DIRECTV L.A. circular LNB required).
Connecting 1 ReceiverConnect an RF cable from the “Receiver” jack on the TV-Hub to the “Satellite In” jack on the receiver (see Figure 29).
Connecting Multiple Receiversa. Run a second RF cable (RF2) from the
antenna (see “Wire the Antenna” on page 8). Be sure to connect a grounding block in-line with the RF1 and RF2 cables from the antenna (see Figure 30 and “Grounding Requirements” on page 23).
b. Connect the RF2 cable from the grounding block to the “13V” jack on the power inserter (supplied in the kit).
c. Connect the “V-OUT” jack on the power inserter to the “18V” jack on the multiswitch (supplied in the kit).
NOTE: If you need to connect more than four receivers, install a multiswitch that has more outputs. KVH offers an 8-output multiswitch (KVH part no. 19-0573).
d. Set the power inserter’s switch to the “17/18V-HORZ, 13/14V-VERT” position.
e. Connect the “Receiver” jack on the TV-Hub to the “13V” jack on the multiswitch.
f. Connect the multiswitch outputs to the “Satellite In” jacks on the receivers.
g. Terminate any unused outputs on the multiswitch with 75terminators and verify all connections are tight.
11
2
Figure 31: Wiring a Tri-Americas System
AC Power
SWM
18V
13V 18V/22KHz
13V/22KHz
DC BlockSplitter
DC BlockSplitter
Antenna Antenna
Secondary Primary Secondary Primary
SWM PowerInserter SWM-8
ModuleSWM1/PWR
AC Power
SWM Receiver/DVRSatellite In
Connect any combination of SWM receivers/DVRsthat add up to 8 or fewer tuners at the SWM splitter
SWM Splitter
Terminateunusedoutputs
Supports up to 8 tuners:Each SWM receiver = 1 tunerEach SWM DVR = 2 tuners
IRD
TV-Hub
DIRECTV LA Receiver
AC Power
Satellite In
Connect up to 2 DIRECTV Latin America receivers
18V 13V
Receiver
13V18V
Multiswitch
GroundingBlock
Antenna
Set switch to “ON” for DIRECTV Latin America
22KHz Tone Generator
LNB
REC
RF1 RF2
Continued Wire the Receivers
0
Tri-Americas WiringFollow these steps to connect both DIRECTV Latin America and DIRECTV U.S. receivers to the TracVision system (see Figure 31) (Tri-Americas LNB required).
a. Run a second RF cable (RF2) from the antenna (see “Wire the Antenna” on page 8). Be sure to connect a grounding block in-line with the RF1 and RF2 cables from the antenna (see Figure 31 and “Grounding Requirements” on page 23).
b. Connect the RF2 cable from the grounding block to the “LNB” jack on the 22KHz tone generator (supplied in the kit).
c. Connect the “REC” connector on the tone generator to the “13V” jack on the multiswitch (supplied in the kit).
d. Connect the “Receiver” jack on the TV-Hub to the “18V” jack on the multiswitch.
NOTE: If you need to connect more receivers, install a multiswitch that has more outputs. KVH offers an 8-output multiswitch (KVH part no. 19-0573).
e. Connect the multiswitch outputs to the “Satellite In” jacks on the DIRECTV Latin America and any non-SWM DIRECTV U.S. receivers. To connect SWM DIRECTV U.S. receivers, connect the external SWM-8 kit (supplied in the kit) to the multiswitch. See “Connecting 9-16 SWM Receivers (or Tuners)” on page 17 for details.
f. Terminate any unused connectors on the multiswitch and SWM splitter with 75terminators and verify all connections are tight.
g. For DIRECTV Latin America service, set the tone generator switch to the “ON” position; when using DIRECTV U.S. service, set the tone generator switch to “OFF.”
11
21
Figure 32: Wiring 1 DISH/Bell Receiver
Receiver
AC PowerSatellite In
TV-Hub
Antenna
RF1
Receiver
Figure 33: Wiring 2 DISH/Bell Receivers
Receiver
AC Power
Satellite In
TV-Hub
Receiver
AC Power
Satellite In
Receiver
DC BlockSplitter
Antenna
Secondary Primary
Figure 34: Wiring 3+ DISH/Bell Receivers
Receiver
AC Power
Satellite In
Receiver
AC Power
Satellite In
TV-Hub
Connect up to 4 receivers
Terminateunusedoutputs
13V18V
Multiswitch
18V
Receiver
DC BlockSplitter
Antenna
Secondary Primary
Continued Wire the Receivers
DISH Network and Bell TV WiringFollow these steps to connect DISH Network or Bell TV receivers to the TracVision system (circular LNB required).
Connecting 1 ReceiverConnect an RF cable from the “Receiver” jack on the TV-Hub to the “Satellite In” jack on the receiver (see Figure 32).
Connecting 2 or More Receiversa. Connect an RF cable from the “Receiver” jack
on the TV-Hub to the “Antenna” jack on the DC block splitter (supplied in the kit).
b. Connect the “Primary” jack on the DC block splitter to the “Satellite In” jack on the first receiver. This receiver will be able to control satellite selection in Automatic satellite switching mode.
c. If you need to connect just a second receiver, connect the “Secondary” jack on the splitter to the “Satellite In” jack on the second receiver (see Figure 33).
If you need to connect three or more receivers, connect the “Secondary” jack on the splitter to the “18V” port on a multiswitch (see Figure 34). KVH offers a 4-output passive multiswitch (KVH part no. 72-0676) and an 8-output active multiswitch (KVH part no. 72-0677).
d. When using a multiswitch, connect the multiswitch outputs to the “Satellite In” jacks on the receivers.
Receivers must be DISH Pro-compatible. Look for the DISH Pro logo on the box.
IMPORTANT!
To enable any of the additional receivers to control satellite selection in Automatic satellite switching mode, install an optional IP Autoswitch (KVH part no. 72-0634) in-line with its RF input. See Appendix A on page 34 for details.
IMPORTANT!
11
2
TV-Hub
OR
B A
1 2
NMEA 0183 Talker
NMEA0183
NMEA 2000 Talker
CAN NetworkBackbone
NMEA2000
Figure 35: TV-Hub NMEA Connections
Figure 36: Supported NMEA 0183 Messages
NMEA 0183 $--xxx Description
HDG Heading, Deviation & Variation
HDM Heading, Magnetic
HDT Heading, True
OSD Own Ship Data
THS True Heading & Status
VHW Water Speed and Heading
RMC GNSS Position Data
Figure 37: Supported NMEA 2000 Messages
PGN Description
127250 Vessel Heading
129029 GNSS Position Data
Connect a NMEA DeviceOptional
2
At the customer’s option, you can connect a NMEA device to the TV-Hub, allowing the antenna to use its GNSS position and heading data to speed up satellite acquisition. The current position and heading will also be displayed on the Home page of the web interface.
NOTE: The antenna system can only use and display true heading. If only magnetic heading is input, the TV-Hub will use the current location data to convert magnetic heading to true heading. Without a built-in GPS or NMEA GNSS input, the user-entered location will be used.
Follow these steps to connect a NMEA device to the TV-Hub, if desired.
NMEA 0183a. Wire and connect the 2-position terminal
strip connector (supplied in the kit) as shown in Figure 35.
b. Configure the NMEA device to transmit one or more of the supported NMEA 0183 messages at 4800 baud (see Figure 36).
NMEA 2000a. Connect the TV-Hub to the vessel‘s
NMEA 2000 CAN network backbone via a “T” connector, as shown in Figure 35. Be sure to use a standard drop cable: 5-wire (4 conductors + shield) twisted pair with micro-C connectors.
b. Configure the NMEA device to transmit one or more of the supported NMEA 2000 messages (see Figure 37).
Later, you will select the NMEA source at the TracVision Setup Wizard (see “Setup Wizard” on page 30).
12
23
DC Power(10-30V, 10A max)
TV-Hub
Receiver
AC Power
Satellite In
Grounding Block
#6 MountingScrew (x2)
Antenna
Receiver
AC Power
Satellite In
Receiver
RF1RF2
Ground
Deck
Figure 38: Grounding Block Example
Connect Power
Before connecting power, be sure the vessel is properly grounded in accordance with marine standards.Grounding RequirementsProper grounding of the TracVision system to ship’s ground is critically important, as it protects the equipment from lightning and electrostatic discharges (ESD). Follow these steps to ground the system.
a. Connect the hoop of the grounding wire (supplied in the kit) to the “Ground” screw on the rear panel of the TV-Hub. Connect the other end to ship’s ground.
b. If multiple RF cables are connected to the antenna, connect one or two grounding blocks in-line with all of the RF cables (a second grounding block is needed for RF3 and RF4). Attach a ground wire from each grounding block to ship’s ground. Then mount each grounding block using the two supplied #6 screws (see Figure 38).
WARNING
Failure to ground the TracVision system properly to the vessel’s ground will cause an unsafe floating ground condition, risking damage to the antenna and electric shock, potentially resulting in DEATH. In a floating ground condition, the difference between the equipment's chassis ground and the vessel’s ground can measure well over 100 volts, when it normally should not exceed 25 volts. Therefore, always measure the difference in potential between chassis ground and the vessel’s ground to make certain that there is no dangerous floating ground condition, even if the ground pin of the vessel's AC power plug appears to be intact.
13
2
Ground
DC Return 10-30 VDC Power,
10A maximum Red
Black
Input
Filter
Fuse Holder with9A 32V SFE Fuse
Figure 39: TracVision System Power
Continued Connect Power
Connect Power to the SystemNOTE: When powering up a SWM configuration, apply power to all other system components before powering up the receivers and DVRs (tuners are assigned SWM channels during startup).Follow these steps to connect power to the TracVision system (see Figure 39).
a. Make sure that the ground wire from the TV-Hub has been connected as described on the previous page.
b. Connect the TV-Hub power cable (supplied in the kit) to the 10-30 VDC power input on the rear of the TV-Hub.
c. Connect the black wire of the TV-Hub power cable to DC return (ship’s ground).
d. Connect the red wire of the TV-Hub power cable to the vessel’s 12 VDC or 24 VDC power source (10-30 VDC is required at the TV-Hub).
NOTE: An optional 24 VDC AC-DC power supply (5 A, 120 W) is available from KVH (part no. 72-0669).
All power connections must be hard wired.
IMPORTANT!
13
4
25
TV-Hub
Power Switch
Figure 40: TV-Hub Power Switch
TV-Hub Antenna Power
Figure 41: TV-Hub Status Lights
Turn On the System
Follow these steps to turn on the system for the first time.a. Ensure the antenna has a clear, unobstructed view of the sky.
b. Press the power switch on the rear panel of the TV-Hub to apply power to the TracVision system (see Figure 40).
c. Within a few minutes, the TV-Hub and Power lights should be lit green (the Antenna light will be flashing green).
d. Plug in and turn on any connected receivers, DVRs, Genie clients, and televisions.
During startup, the TV-Hub checks the software versions installed in the antenna and updates them if necessary to match the versions it has stored for that model. All three status lights (see Figure 41) will alternate orange while this update is in progress. Do not turn off the system during this time. Updates might take up to 40 minutes.
IMPORTANT!
14
2
Figure 42: Wi-Fi Connection
TV-Hub
TV-Hub
Ethernet
169.254.253.1
Figure 43: Wired Ethernet Connection
Access the Web Interface
6
Follow the steps for either option below to access the TV-Hub’s web interface.
Using the Wireless Connectiona. Select the TVHub-<TV-Hub serial number>
network from your device’s Wi-Fi settings to connect to the TV-Hub (see Figure 42).
b. Start your web browser and enter http://tvhub.kvh. If the web interface does not appear, try entering http://172.16.0.1, which is the default IP address of the TV-Hub.
Using the Ethernet Connectiona. Connect a laptop PC configured for DHCP
directly to the “Ethernet” port on the TV-Hub (see Figure 43).
b. Start your web browser and enter http://169.254.253.1.
NOTE: When connected to a vessel’s LAN (see “Connect to an Onboard Network” on page 27), you will need to enter the IP address (dynamic or static) assigned to the TV-Hub. If your laptop has Bonjour® installed, you can use it to find the TV-Hub on the network without knowing its IP address.
15
27
Onboard Network (LAN)12VDCPOWER
ResetEthernet Internet4321
TV-Hub
Wireless Router
Ethernet
Figure 44: TV-Hub Network Connections
Figure 45: TV-Hub Reset Button
TV-Hub
Figure 46: Web Interface Ethernet Settings
Connect to an Onboard NetworkOptional
Connecting the TV-Hub to an onboard local area network (LAN) is required if any of the following conditions apply:
• One or more IP AutoSwitches are installed to enable automatic satellite switching (Linear/DISH Network/Bell TV only)
• Customer wants to access the TV-Hub’s web interface using any device connected to the onboard network (see Figure 44)
NOTE: Connecting the TV-Hub to the onboard network using its Wi-Fi rather than an Ethernet cable is not recommended because you lose the ability to connect directly to the TV-Hub’s built-in Wi-Fi. You will always need to connect via the network.
NOTE: The Reset button on the rear panel of the TV-Hub (see Figure 45) reverts all network settings back to their original factory settings.
Wired LAN Connectiona. Connect the “Ethernet” port on the TV-Hub
to the onboard network (LAN) using the supplied Ethernet cable.
b. By default, the TV-Hub’s Ethernet port is configured as a DHCP client, and the network’s router automatically assigns it an IP address. However, in this Dynamic mode, the TV-Hub could get assigned a different IP address whenever it is turned on.
KVH recommends that you set the TV-Hub to Static mode and enter a static IP address at the web interface (see Figure 46) (go to Settings > Network Settings). Be sure to choose a static IP address that is outside the router’s DHCP range (refer to the router’s user manual for details on finding its range.)
For systems with IP AutoSwitch(es), make sure they are on the same local LAN segment as the TV-Hub (see Appendix A on page 34).
For DIRECTV systems set up for automatic satellite switching, make sure the receiver(s) have IP addresses in the same subnet as the TV-Hub (see Appendix B on page 38).
IMPORTANT!
16
2
Figure 47: TV-Hub Security and Password Setting
Secure the Wi-Fi Connection
8
By default, the TV-Hub’s wireless settings are configured for the following:
• Wireless Mode: AP (Access Point)
• SSID: TV-Hub-<TV-Hub serial number>
• IP Address: 172.16.0.1
• Security Mode: Off
KVH strongly advises that you select the WPA_PSK security mode as shown in Figure 47 and assign a unique password to prevent unauthorized access to the TV-Hub (at the web interface, go to Settings > Network Settings). If you keep the default settings, you’re allowing anyone to access the TV-Hub with their mobile device.
KVH strongly recommends that you keep the TV-Hub set to AP (Access Point) wireless mode. If you select IF (Infrastructure) mode to connect the TV-Hub to your onboard network, you will no longer be able to access the TV-Hub’s web interface directly.
IMPORTANT!
17
29
Figure 48: Setup Wizard Welcome Page
Figure 49: Software Updates Page
Set Up the System
The Setup Wizard appears upon initial startup to step you through system configuration (see Figure 48). Before you begin to set up the system:• Know the service provider and associated satellite(s)
• Check the latest software version (see below)
• Verify all system components are connected
Update Software and Satellite LibraryBefore you start the Setup Wizard, update the system software and satellite library to the latest versions. Use the Apple® iOS or Android™ smartphone/tablet mobile app, or follow these steps to use a laptop PC that has the latest update files downloaded to it from the KVH Partner Portal (www.kvh.com/partners).
a. Select Exit in the Setup Wizard page. The web interface appears.
b. At the Updates page of the web interface, select the antenna model. Then select Install Update (see Figure 49). Find the .kvh file in your downloads folder, then double-click to install.
c. Wait for the update to complete. It may take up to 45 minutes. The TV-Hub’s lights will alternate orange while the update is in progress. Once complete, the web interface will report that the latest version is installed.
d. When the software update is complete, select the Satellite Library. Then select Install Update. Find the .xml file in your downloads folder, then double-click to install.
e. Close the web interface. Then reopen it (see “Access the Web Interface” on page 26). The Setup Wizard will reappear since setup has yet to be completed.
f. Select Proceed with Setup Wizard.
18
3
Figure 50: Preset Satellite Groups
Note: This list is subject to change.
Service Satellites (A-B-C-D)
Linear Europe 1: Hotbird, Astra1, Astra2S, Astra3Europe 2: Astra3, Astra1, Hotbird, Astra2SScandinavia: Astra4, Thor, Hotbird, Astra1
DIRECTV U.S. DIRECTV Dual: 101W and 119W
DISH Network
Western Arc: 110W, 119W, 129WEastern Arc: 61W, 72W, 77WLegacy East Arc: 61W, 110W, 119WDISH 500: 110W, 119W
Bell TV Bell TV Dual: 82W, 91W
Tri-Americas (DIRECTV U.S. + Latin America)
Tri-Am TriSat: 101W, 119W, 95WTri-Am Dual: 101W, 95W
Continued Set Up the System
Setup WizardSystem configuration continues by prompting you to enter information or perform certain tasks, as necessary. For example:
• Enter installer and vessel information
• Select a source for GNSS position data
• Select a source for heading data (if NMEA device is connected)
• Select the satellite TV service
• Select satellite(s) to track (make your own selections or select one of the preset groups listed in Figure 50), or create user-defined satellites
• Set up automatic switching, if applicable
Additional Setup InformationOnce the Setup Wizard has been completed, perform follow-up tasks such as:
• Set up receivers to operate with the system (as instructed by the Wizard)
• Activate the receivers (as instructed by the Wizard)
• Set the antenna’s LNB to the skew angle provided by the Wizard (see “Set the LNB Skew Angle” on page 32; applies to linear manual skew systems only)
18
0
31
Figure 51: Linear Receiver DiSEqC Settings (Example)
Continued Set Up the System
Linear Receiver Setup for Automatic SwitchingFor automatic switching to work properly using the DiSEqC communications protocol, set up linear receivers for the same satellites installed in the TracVision system. Set up the satellites in the receiver in the exact same order as they were set up in the antenna. The specific setup process varies among receiver models – refer to the receiver’s manual for details. Use the table below and Figure 51 as a guide.
Satellites in Antenna
Matching Satellitesin Receiver
Slot A Port/Switch/LNB/DiSEqC 1 or A
Slot B Port/Switch/LNB/DiSEqC 2 or B
Slot C Port/Switch/LNB/DiSEqC 3 or C
Slot D Port/Switch/LNB/DiSEqC 4 or D
18
3
Figure 52: Location of LNB on Back of Antenna Reflector
Reflector
M4 SocketSet Screws
Figure 53: Set Screws Securing the LNB to the Reflector
0˚ SkewPositiveSkews
NegativeSkews
010 2040 50
70 80
30
90
60
50
10203040
6070
8090
5 515 1525
3545
25 35 45 55
6575
85
5565
7585
LNB
Choke Feed
LNB*
*actual LNB not shown
SKEW ADJUSMENT
Figure 54: LNB Skew Angle Adjustment
Set the LNB Skew AngleLinear Manual Skew Only
2
Follow these steps to set the antenna’s LNB to the skew angle supplied by the Setup Wizard.
a. At the rear panel of the TV-Hub, set the power switch to the Off position. Verify its Power light goes out.
b. Remove the antenna’s radome as described on page 9.
c. Locate the LNB on the back of the antenna’s reflector (see Figure 52).
d. Using a 2 mm Allen hex key, loosen the two M4 set screws securing the LNB to the choke feed (see Figure 53).
e. Adjust the LNB, clockwise or counter-clockwise, until the skew arrow on the LNB points to the correct skew angle you noted when running the Setup Wizard (see Figure 54).
f. Tighten the two M4 socket set screws to secure the LNB in place. Apply 11 in-lbs (1.2 N-m) of torque, if possible.
g. Reinstall the radome.
CAUTION
Disconnect power from the antenna before you remove the radome. The antenna has moving parts that can cause injury.
Make sure the LNB is fully inserted into the choke feed to ensure optimum performance.
IMPORTANT!
19
33
Figure 55: Satellite Switching Selection on Home Page
Figure 56: Master Receiver Selection
TracVision
Figure 57: Blockage Example
Educate the Customer
Before you leave the vessel, test the system to ensure the antenna works properly. Fill out the Installation Checklist (provided in the Welcome Kit) and return it to KVH. Refer to the instructions on the form.Give the Welcome Kit to the customer, provide any passwords and static IP addresses you set up, and explain how to use the system. Ensure the customer understands the following.
• How to:• Turn on the system• Access the web interface• Switch satellites (see Figure 55)• Select a master receiver (see Figure 56)• Interpret TV-Hub status information• Download software and satellite library
updates (using web interface and/or mobile app)
• Perform general troubleshooting
• Keep the radome installed on the antenna at all times. The radome protects the antenna’s moving parts from wind, rain, and debris.
• The antenna must have a clear view of the sky to receive satellite TV. Common causes of blockage include trees, buildings, bridges, and onboard equipment (see Figure 57). Heavy rain or snow might also temporarily interrupt reception.
• Clean the antenna regularly. Dirt buildup on the radome can affect satellite TV reception.
• You must be located within the satellites’ coverage area to receive TV signals. Visit www.kvh.com/footprint for coverage maps.
• Please register the system to ensure the best possible service from KVH. Visit www.kvh.com/register for details.
CAUTION
In the unlikely event that you need to remove the radome, remove power from the antenna first because the antenna’s moving parts can cause injury.
20
3
Figure 58: IP AutoSwitch
Figure 59: Serial Number and Master Select Button
Serial Number
Master Select Button
Installing an IP AutoSwitchAppendix
4
Follow these steps to add an IP AutoSwitch (KVH part no. 72-0634) to each DISH Network, Bell TV, or linear receiver you want to be able to control satellite selection in Automatic satellite switching mode.
NOTE: A receiver connected directly to the TV-Hub’s “Receiver” jack can control satellite selection without an IP AutoSwitch.
Inspect PartsFollow these steps to inspect the kit contents.
a. Unpack the box and ensure it contains each of the following items:
• 3 ft (1 m) Ethernet cable
• 2 ft (60 cm) RF cable
• 1.3 ft (40 cm) RF cable
• 22 KHz tone blocker
• Adhesive-backed Velcro strip
b. Carefully examine all of the supplied parts to ensure nothing was damaged in shipment.
c. Locate the serial number on the bottom of theIP AutoSwitch (see Figure 59) and record it on the Installation Checklist (supplied in the Welcome Kit) for future reference.
Choose a Mounting LocationChoose a mounting location that meets the following requirements:
• Dry, well-ventilated, and away from heat sources
• Provides a clear view of and easy access to the Master Select button (see Figure 59)
• Provides adequate clearance for running the cables and allows for service loops and strain relief
• Within 2 ft (60 cm) of the associated receiver in order to use the supplied cable
• Either a horizontal or vertical surface
A
35
Connect up to 3 IP AutoSwitches
4 3 2 18 7 6 5
POE 48V
+
Switch
* Network ConnectionsConnect the TV-Hub and IP AutoSwitch(es) to your onboard network. If you do not have a network, installa router or router and switch as shown below.
Connect up to 7 IP AutoSwitches
OR
Router
12VDCPOWER
ResetEthernet Internet4321
AC Power
Connect up to 2 IP AutoSwitches
Router
12VDCPOWER
ResetEthernet Internet4321
To TV-Hub
AC Power
AC Power
TV-Hub
Receiver
AC Power
Satellite In
IP AutoSwitch
To Receiver
RF InNetwork
** Varies depending on your system configuration
RF Input**
22 KHzToneBlocker
Out
In
To IP AutoSwitch
13V18V
Multiswitch
To Network*
ANTIN
Or
RF Input**
Figure 60: IP AutoSwitch Connections
Continued Installing an IP AutoSwitch
Wire the IP AutoSwitchThe wiring of the IP AutoSwitch depends on the specific configuration. Refer to the wiring diagrams provided in “Wire the Receivers” on page 13, while following the general wiring steps below:
a. Disconnect the RF input cable from the receiver and connect it to the “RF In” jack on the IP AutoSwitch. Then tighten to 15 in.-lbs of torque.
b. Connect the supplied 2 ft (60 cm) RF cable from the “To Receiver” port on the IP AutoSwitch to the receiver’s satellite input and tighten to 15 in.-lbs of torque.
NOTE: If you are using a 3-input passive multiswitch (e.g., KVH Part No. 72-0676 or 72-0310), install a 22 KHz tone blocker (supplied in kit) inline between the multiswitch and the IP AutoSwitch (see Figure 60).
c. Using the supplied Ethernet cable, connect the “Network” port of the IP AutoSwitch to the onboard network. If a network is not available, install a router as shown in Figure 60.
d. If not already connected, connect the TV-Hub to the onboard network (see Figure 60).
e. Using the supplied Velcro strip, secure the IP AutoSwitch to the mounting surface.
A
3
Figure 61: Add IP AutoSwitch Screen
140701234
Figure 62: IP AutoSwitch LED Status Indications
LED Color Indication
Orange Registered with the system but not currently the master
Orange, flashing
Initializing
Red Error:• unable to communicate with
the system,• network is not detected, or• unable to register
Green Registered with the system and currently the master
Continued Installing an IP AutoSwitch
6
Configure the IP AutoSwitchWhen performing system setup (see “Set Up the System” on page 29), follow these additional steps to configure the IP AutoSwitch.
NOTE: KVH recommends that you run the Setup Wizard in the web interface whenever you change your system’s configuration by adding or removing devices.
a. At the AutoSwitch page of the web interface, select Add IP AutoSwitch (Figure 61).
b. Enter the serial number and choose a friendly name for the IP AutoSwitch (for example, “Salon”).
c. Select Save to save your changes.
Select the Master ReceiverAny receiver connected to an IP AutoSwitch can become the master receiver for the system. The master receiver controls satellite selection.
a. To choose the master receiver, select it on the Home page of the web interface, or press the Master Select button on the associated IP AutoSwitch.
b. Verify that the LED in the Master Select button on the IP AutoSwitch is lit green (see Figure 62). The LEDs for any other IP AutoSwitches should be lit orange.
The TV-Hub has a built-in IP AutoSwitch. Any receiver connected directly to the TV-Hub can therefore be selected as a master receiver through the web interface.
IMPORTANT!
A
37
Figure 63: Band/Polarization Control Setting
Figure 64: Linear Receivers with Multiswitch and IP AutoSwitch
TV-Hub
12VDCPOWER
ResetEthernet Internet4321
Router
Master Receiver
13V 13V/22KHz
18V/22KHz
IP AutoSwitch
Receiver
Voltage/Tone ofMultiswitch Port
Voltage/Tone of Selected Channel
18V
13V 18V/22KHz
13V/22KHz
18V
Multiswitch
Receiver
Continued Installing an IP AutoSwitch
Band/Polarization ControlIf your configuration consists of linear receivers connected via a multiswitch, and you installed one or more IP AutoSwitches, KVH recommends that you change the TV-Hub’s Band/Polarization Control setting to TV-Hub (see Figure 63). You can find this setting on the Advanced Settings page of the web interface (go to Settings > Advanced Settings).
DescriptionTV channels can be carried on any of a linear satellite’s four combinations of frequency band and polarization. Since only one of these signals can be delivered to a receiver at any one time, the receiver outputs a voltage/tone to request the band/polarization for the selected channel:
Since the voltage/tone from the master receiver could differ from the voltage/tone present on the TV-Hub’s “Receiver” jack, the TV-Hub will output band/polarization on that jack based on the Band/Polarization Control setting:
• Master Receiver (default setting): The output of the TV-Hub’s “Receiver” port is the band and polarization that is currently selected by the master receiver. This setting ensures the antenna always has a valid band/polarization on which to track the satellite.
• TV-Hub: The TV-Hub ignores voltage/tone from the master receiver and outputs whichever band/polarization corresponds to the voltage/tone that is present on the coax cable connected to its “Receiver” port (see Figure 64). This allows a multiswitch to continue receiving all four combinations of band/polarization from the antenna.
Voltage Tone Polarization Band
13 VDC Off Vertical Low
18 VDC Off Horizontal Low
13 VDC On Vertical High
18 VDC On Horizontal High
A
3
Figure 65: Non-Genie Configuration
TV-Hub
AC Power
DC to RFAdapter
PowerSupply
New Receiver Models:HR24, H24, H25
AC PowerSatellite In
Ethernet
Connect any combination of SWM receivers/DVRsthat add up to 8 or fewer tuners at the SWM splitter
DECA
SWM SplitterSupports up to 8 tuners:Each SWM receiver = 1 tunerEach SWM DVR = 2 tuners
Can connect via an onboard network (router), if desired
SWM
Using a DIRECTV Coax NetworkAppendix
In Automatic satellite switching mode, the TV-Hub can accept commands from the master SWM-compatible DIRECTV receiver to automatically switch between the 101W and 119W satellites. The TV-Hub communicates with the master receiver via the TV-Hub’s Ethernet port link to the DIRECTV coax network. Follow the steps in this section to set up this communication link with SWM-compatible receivers
NOTE: The 119W satellite only carries local channels for certain regions of the country. (You can find a list of these regions in the Setup Wizard.) If the customer’s locals are carried on DIRECTV’s main 101W satellite, there is no need to switch satellites.
DIRECTV Coax Network ConnectionsDIRECTV recently adopted coax networking technology, by which both satellite TV signals and network communications data are carried by the coax cables. This simplifies installation, since Ethernet cables don't need to be run to all of the receivers.
Non-Genie ConfigurationsIf a Genie DVR (HR44 or HR34) is not present on the DIRECTV SWM network, you need to install a DECA with power supply and DC to RF adapter, collectively referred to as a DECA Broadband Kit (KVH part no. 19-0860) and formerly called a Cinema Connection Kit. When connected to the SWM splitter and the TV-Hub's Ethernet port, either directly or via an onboard router, the DECA relays messages between the DIRECTV coax network and the Ethernet network (see Figure 65).
B
8
39
Figure 66: Genie Configuration
RAUDIO OUT
L
PrPbY
VIDEO OUT S-VIDEO OUT
DIGITALAUDIO OUT
ETHERNET
SATELLITE IN 1
IR RECEIVE SATA HDMI PHONE JACK
POWER INPUT
USB
COMPONENT VIDEO OUT
Satellite InAC Power
Ethernet
Genie DVR:HR34 or HR44
Genie Client Models:C31, C41
Network
New Receiver Models:HR24, H24, H25
AC PowerSatellite In
AC Power
TV-HubEthernet
Connect any combination of SWM receivers/DVRsthat add up to 8 or fewer tuners at the SWM splitter
SWM Splitter
Can connect via an onboard network (router), if desired
SWM
Supports up to 8 tuners:Each SWM receiver = 1 tunerEach SWM DVR = 2 tunersEach Genie DVR = 5 tunersEach Genie client = 0 tuners
Continued Using a DIRECTV Coax Network
Genie ConfigurationsFull DECA Broadband functionality is built into Genie DVRs (HR44 or HR34). So if a Genie DVR is present on the DIRECTV SWM network, no external DECA Broadband kit is required. Just connect the Genie's Ethernet port to the TV-Hub's Ethernet port, either directly or via an onboard router (see Figure 66). The Genie DVR provides the link between the DIRECTV coax network and the Ethernet network.NOTE: If you cannot easily connect the Genie DVR’s Ethernet port to the TV-Hub or an onboard network, you can use a DECA Broadband Kit, as explained in “Non-Genie Configurations” on page 38.
NOTE: Genie clients cannot switch satellites; they can only view programming carried by the satellite that is currently selected.
B
4
Figure 67: Additional Equipment for Older Receivers
* Model HR20-100 may require additional hardware. Contact KVH Technical Support for details.
Satellite In
Old Receiver Models:H21, H22, H23, HR21,HR22, HR23
Satellite In
Old Receiver Models:H20*
Ethernet
DECA
Band Stop Filter
SWM Splitter
Continued Using a DIRECTV Coax Network
Additional Equipment for Older ReceiversIn addition to the DECA Broadband Kit or a Genie DVR, you might need to connect an additional device in-line between the receiver and the SWM splitter, depending on the model (see Figure 67).
NOTE: Model HR20-100 requires additional devices not specified here. Contact KVH Technical Support.
H21, H22, H23, HR21, HR22, and HR23These receivers do not have built-in DECA functionality, but they have an Ethernet port for network connectivity. An additional DECA (KVH part no. 19-0860) is required to support coax networking, supplying the satellite TV signal to the receiver's "Satellite In" port and network communications data to its Ethernet port. (If there are two of each port, use the "Satellite In 1" and "Ethernet 1" ports.)
NOTE: Each DECA you connect directly to a receiver is powered by the receiver. They do not require the separate power supply included in the kit.
H20This receiver is not network-ready. It is only designed to receive a satellite TV signal via its "Satellite In" port. Since both the satellite TV signal and network communications data are present on the coax cables, a band stop filter (KVH part no. 19-0868) is required to block the network data to prevent potential damage to the receiver. Since the H20 cannot communicate over the network, it cannot control satellite selection.
Be sure to connect all band stop filters before connecting the coax cables.
IMPORTANT!
B
0
Figure 68: IP Addressing for Automatic Switching (Example)
TV-Hub
AC Power
DC to RFAdapter
PowerSupply
AC Power
DECA
AC Power
Static IP Address: 192.168.184.2Receiver #1
SWM Splitter
Static IP Address: 192.168.184.3Receiver #2
TV-Hub Serial Number140901484
192.168.184.1TV-Hub IP Address
for Automatic Switching
Figure 69: Router DHCP Settings (Example)
Continued Using a DIRECTV Coax Network
Configuring the DIRECTV Receivers for Automatic SwitchingTo establish communications between the TracVision system and each SWM-compatible DIRECTV receiver for automatic satellite switching, you need to set each receiver to a static IP address and enter that address, along with the receiver's location, in the TV-Hub's web interface.
Static IP Address Range WITHOUT an Onboard NetworkIf the DECA Broadband Kit or Genie DVR is connected directly to the TV-Hub's "Ethernet" port (no router is installed), set each receiver's IP address to any address ranging from 192.168.x.2 to 192.168.x.149, where x=1<the last 2 digits in the TV-Hub’s serial number>.
For example, if the serial number of the TV-Hub is 140901484, you might assign an IP address of 192.168.184.2 (see Figure 68). Refer to the instructions in “Assigning Static IP Addresses to DIRECTV Receivers” on page 42. The TV-Hub has a hidden IP address of 192.168.x.1 reserved for automatic switching communications. This IP address is not shown on the Network Settings page of the web interface.
Static IP Address Range WITH an Onboard NetworkIf the TV-Hub and the DECA Broadband Kit or Genie DVR are connected to an onboard network (i.e., router), set each receiver to a static IP address that is outside the router's DHCP range (see Figure 69). (Refer to the router's user manual for details on finding its IP address range.) For example, if the router has an IP address of 192.168.1.1 and assigns IP addresses ranging from 192.168.1.100 to 192.168.1.149 via DHCP, you could set each receiver's IP address to any address ranging from 192.168.1.150 to 192.168.1.254. Refer to the instructions in “Assigning Static IP Addresses to DIRECTV Receivers” on page 42.
B
41
4
Figure 70: IP Address on a DIRECTV Receiver (Example)
WITHOUT an Onboard Network (No Router)
WITH an Onboard Network (Using a Router)
Continued Using a DIRECTV Coax Network
Assigning Static IP Addresses to DIRECTV ReceiversOnce you have identified a valid static IP address range for the receivers, follow these steps to assign a unique static IP address within that range to each receiver.NOTE: These steps may vary, depending on the receiver's model and software version. Refer to the receiver's owner's manual for details.
a. Press MENU on the receiver's remote control to access the onscreen menu.
b. At the main menu, highlight Settings & Help. Then select Settings.
c. Highlight and select Network Setup.
d. Select Advanced Setup.
e. Change the IP address to the new static IP address. (On a Genie DVR, the IP address is called the "Server IP") (see Figure 70).
f. WITHOUT an Onboard NetworkEnter "255.255.255.0" for the subnet mask, and enter the TV-Hub's IP address for default gateway and DNS.
WITH an Onboard NetworkEnter the router's subnet mask, and enter the router's IP address for default gateway and DNS.
g. Highlight and select Connect Now to save your changes. Disregard any error messages about missing Internet connectivity. Note this receiver's IP address and location onboard for future reference.
h. Repeat this procedure for each additional receiver. Be careful not to use the same IP address twice.
B
2
Figure 71: Adding a DIRECTV Receiver to the Autoswitch Page
Continued Using a DIRECTV Coax Network
i. Add the new receivers to the Autoswitchpage of the web interface. Enter each receiver’s static IP address and assign it a friendly name (e.g., “Salon”) (see Figure 71).
Also be sure to set each receiver’s Dish Type to 3-LNB and Switch Type to SWM, and enable external device access, as directed by the TV-Hub’s Setup Wizard. If the TV-Hub is then unable to communicate with the receiver, try resetting the receiver (press its red reset button or unplug it, wait 15 seconds, then plug it back in and turn it on).
IMPORTANT!
B
43
www.kvh.com
KVH Industries, Inc.World Headquarters
Middletown, RI U.S.A.Tel: +1 401 847 3327 Fax: +1 401 849 0045
E-mail: info@kvh.com
KVH Industries A/SEMEA HeadquartersKokkedal, Denmark
Tel: +45 45 160 180 Fax: +45 45 160 181E-mail: info@emea.kvh.com
KVH Industries Pte Ltd.Asia-Pacific Headquarters
SingaporeTel: +65 6513 0290 Fax: +65 6472 3469
E-mail: info@apac.kvh.com