Post on 25-Apr-2020
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 1 of 62
ALL INDIA INSTITUTE OF MEDICAL SCIENCES (AIIMS) BHOPAL
Saket Nagar, Bhopal-462020 (Madhya Pradesh) India
Website : www.aiimsbhopal.edu.in
NOTICE INVITING TENDER
Tender No.111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-15/01 Dtd.11/02/2015
On behalf of Director, All India Institute of Medical Sciences (AIIMS) Bhopal, Notice Inviting Tender for Supply of
Orthopaedics Indian Implants at AIIMS Bhopal are invited under Two Bid System in sealed cover.
Detailed Description and Term & Conditions of Tender Document may be seen and downloaded from AIIMS
Bhopal website www.aiimsbhopal.edu.in or may be obtained directly from the Office of Store Officer, 1st Floor, E-
Wing, Medical College Building, AIIMS Bhopal, Saket Nagar, Bhopal-462024 (MP) on any working day from
11.02.15 to 09.03.15 from 10.00 Hrs to 17.00 Hrs except Saturday/Sunday/Holyday on paying Cost of Tender
Document (i.e. Rs. 525/-(Non Refundable) in the form of DD, withdrawn from any Nationalized Bank in favour of
“Director, AIIMS Bhopal”). Last date of submission of tenders is 10.03.15 (Up to 14.00 Hrs) in the Tender Box kept
in the Office of the undersigned.
(Admin Officer)
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 2 of 62
Tender No.111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-15/01, Dated.11/02/2015
Notice Inviting Tender for Rate Contract for Supply of Orthopaedics Indian Implants at AIIMS Bhopal
On behalf of Director, AIIMS Bhopal, the Admin. Officer, AIIMS Bhopal, invites sealed tender under “TWO BIDS
(TECHNICAL & FINANCIAL) SYSTEM” in prescribed tender document from firms/manufacturers/suppliers for
“Supply of Indian Implant for Orthopaedics at AIIMS Bhopal”.
Schedule of Requirement (Specification Given On Chapter-3, Page No-12 to 28)
S. No. Description EMD Group
Wise (in Rs.)
Group-1 (Set-
1,2,3,4,9 )
Stainless Steel Plates (4.5mm) and Screws Set
Group-1
21,700/-
Titanium Plates and Screws Set
Titanium Locking Compression Plates and Screws Set
Stainless Steel Locking Compression Plates and Screws Set
Screws, Drill Bits, and Bone Taps
Group-2 (Set-
5,6,7,8)
Interlocking Nails (Stainless Steel) Group-2
9,605/- Interlocking Nails (Titanium) Condylar Blade Plate, DHS & DCS set
Nails, and Wires -Stainless steel
Group-3 (Set-
10,11,13,14)
Implants for Hip Arthroplasty Group-3
10,030/- Arthroscopic Implants for Knee and Shoulder Joints
Implants for Spinal Surgery
External Fixation Set
Group-4 (Set-
12) Custom made Implants for Tumour Surgery Group-4
16,800/-
ALL INDIA INSTITUTE OF MEDICAL SCIENCES (AIIMS) BHOPAL
Saket Nagar, Bhopal-462020 (Madhya Pradesh) India
Website : www.aiimsbhopal.edu.in
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 3 of 62
SCHEDULE OF TENDER
Sr. No. Schedule Particulars
1 Cost of Tender Form Rs. 525/- (Five Hundred Twenty Five Only) Non Refundable in the
Form of DD in favour of “Director, AIIMS Bhopal” from any
Nationalized bank. Those who have downloaded the tender
document should accompany above Tender Document cost DD in
Technical Bid Envelop.
2 Date of issue of Tender Document 11.02.2015
3 Last date of Sale of Tender Document 09.03.2015
4 Pre-Bid Conference at AIIMS Bhopal 16.02.2015 at 15:00 Hrs. at 1
st Floor, Medical College Building, AIIMS
Bhopal, Saket Nagar, Bhopal.
5 Date of submission of tender 10.03.2015; 14.00 Hrs
6 Date of Opening of Technical Bid 10.03.2015; 15.00 Hrs
7 Earnest Money Deposit The FDR/BG of EMD group wise of Group-1: 21,700/- , Group-2: 9,605/-, Group-3: 10,030/-, Group-4: 16,800/- is to be drawn in favour of “Director, AIIMS Bhopal” from any Nationalize Bank In respect of successful bidder it will be returned after the submission of Performance Security Deposit to AIIMS Bhopal and Performance Security Deposit should remain valid for a period of Ninety Days beyond the date of completion of all contractual obligations including 36 Months Warranty. Any other dues outstanding shall also be recovered from the Performance Security Deposit. In the case of unsuccessful Bidders, the EMD shall be refunded within 30 days of award of contract to successful bidder/bidders.
Note: - The details of Tender Terms &Conditions are mentioned in Tender Document.
1. Tender Form can be purchased from Office of Store Officer, 1st
Floor, E-Wing, Medical College Building AIIMS Bhopal by paying Cost of Bid Document of Rs. 525/- (Five Hundred Twenty Five Only) Non Refundable in form of Demand Draft of any Nationalized Bank drawn in favour of “DIRECTOR, AIIMS BHOPAL” payable at BHOPAL from 11.02.15 to 09.03.15 in all working days from 10.00 Hrs. to 17.00 Hrs. except Saturday/Sunday/Holyday or downloaded directly from AIIMS Bhopal website www.aiimsbhopal.edu.in. Those who have downloaded the tender document from website should must have enclose a DD for Rs. 525/- (Five Hundred Twenty Five Only ) along with their Technical Bid (NON-REFUNDABLE) BY WAY OF SEPARATE DEMAND DRAFT DRAWN IN FAVOUR OF DIRECTOR, AIIMS, BHOPAL AND THE SAME SHOULD ESSENTIALLY BE ENCLOSED ALONGWITH THE TECHNICAL BID. THE BIDDERS SHOULD SPECIFICALLY SUPERSCRIBE, “DOWNLOADED FROM THE WEBSITE” ON THE TOP LEFT CORNER OF THE OUTER ENVELOPE CONTAINING TECHNICAL BID & FINANCIAL BID SEPARATELY. IN NO CASE, THE TENDER COST FEE SHOULD BE MIXED WITH EMD AMOUNT. THE TENDERS NOT FOLLOWING THE ABOVE PROCEDURE, THEIR BIDS WILL BE SUMMARILLY REJECTED.
2. The Director, AIIMS Bhopal reserves the right to reject any or all tenders without assigning any reasons whatsoever.
3. Interested Bidders are advised to visit AIIMS Bhopal website www.aiimsbhopal.eud.in for details of this Tender Document.
Enclosed: Tender Document
(Admin Officer)
Copy to:
1. Director/Dy. Director(Admin)/MS/Financial Advisor/Store Officer of AIIMS, Bhopal
2. Notice Board of MS/Admin/Store Department for wider publicity and Vendors information.
3. IT Department, AIIMS Bhopal- Requested for upload the same in the AIIMS Bhopal Websitewww.aiimsbhopal.edu.in /
www.aiimsbhopal.nic.in / CPP Portal www.eprocure.gov.in for wider publicity.
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 4 of 62
ALL INDIA INSTITUTE OF MEDICAL SCIENCES (AIIMS) BHOPAL
Saket Nagar, Bhopal-462020 (Madhya Pradesh) India
Website : www.aiimsbhopal.edu.in
TENDER DOCUMENT
Supply of Orthopaedics Indian Implants at AIIMS Bhopal Cost of Tender Document: Rs. 525/- (Five Hundred Twenty Five Only)
Non-Refundable.
( To be submitted in the form of Demand Draft, from any Nationalized Bank in favour of “Director, AIIMS Bhopal”;Those who has downloaded tender document directly from AIIMS Bhopal website www.aiimsbhopal.edu.in must accompany the cost of Tender Document DD as mentioned above along with their Technical Bid document envelope, failing which their bids shall be out rightly rejected).
IMPORTANT DATES
Publication of NIT in the News papers
Uploading of NIT on AIIMS Bhopal
websitewww.aiimsbhopal.edu.in
: 11.02.2015
11.02.2015
Date of issue of Tender Document : 11.02.2015
Last Date of Sale of Tender Document : 09.03.2015
Last Date & time for submission of Tender Document : 10.03.2015 up to 14.00 Hrs. At the Tender Box
kept at the Office of Store Officer, 1st
Floor, E-
Wing, Medical College Building, AIIMS Bhopal,
Saket Nagar, Bhopal-462 020 (MP)
Pre-Bid Conference at AIIMS Bhopal : 23.02.2015 at 15:00 Hrs. at 1st
Floor, Medical
College Building, AIIMS Bhopal, Saket Nagar,
Bhopal.
Date & time for opening of Technical Bid : 10.03.2015 at 15.00 Hrs. In the 1st
Floor, Medical
College Building, AIIMS Bhopal, Saket Nagar,
Bhopal-462 020 (MP)
Date & time for opening of Financial Bid : Will be intimated separately in due course of
time to only those Bidders, Qualify in Technical
Bid (i.e. whose bids found “Technically
Responsive”).
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 5 of 62
ALL INDIA INSTITUTE OF MEDICAL SCIENCES (AIIMS) BHOPAL
Saket Nagar, Bhopal-462020 (Madhya Pradesh) India
Website : www.aiimsbhopal.edu.in
Tender No.111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-15/01, Dated.11/02/2015
NOTICE INVITING TENDER
for Rate Contract for Supply of Orthopaedics Indian Implants at AIIMS Bhopal
1. Sealed tenders are invited under two bid system (Part-I Earnest Money and Technical bid & Part-II Financial bid) from
prominent Manufacturers/Authorised Dealers/Whole-sellers on annual Supply basis, for a period of one year from the date of commencement of award. If the performance is found satisfactory, the contract would be extendable further for a period as may be agreed mutually (but not beyond three year that too extendable on Yearly basis) by both the parties.
2. The cost of Tender Document is Rs. 525/- (Five Hundred Twenty Five Only) (Non RefundableTender document can be had in person from the Office of the Store Officer on any working day from 11.02.15 to 09.03.15 during 10:00 to 15.00 Hrs except Saturday/Sunday/Holyday on payment of said cost in the form of Demand Draft in favour of “Director, AIIMS Bhopal”, payable at Bhopal. The Tender Document can also be downloaded from the AIIMS website (http://www.aiimsbhopal.edu.in). In this case it is necessary for the Tenderer to pay the cost in the form of Demand Draft drawn in favour of “Director, AIIMS Bhopal”, payable at Bhopal and is kept in the Technical Bid Envelope. The reference of the DD is to be super scribed on the main envelope of Technical Bid.
3. The amount of Earnest money deposit (EMD) is item wise of Group-1: 21,700/- , Group-2: 9,605/-, Group-3:
10,030/-, Group-4: 16,800/- (Non-Interest bearing). This Earnest money deposit is compulsory and equal to all the prospective bidders, whether they are bidding for single Item or all the items as per the requirement list given in Chapter-7 of this Tender Enquiry Document by any bidder want to participate in this Tender. The Bidder is required to deposit earnest money along with their Technical Bid document in Technical Bid Envelope in the form of Banker’s Cheque/Demand Draft (Non-Interest Bearing)/FDR from any Nationalized Bank and the same should be drawn in favour of “Director, AIIMS Bhopal” payable at Bhopal.
4. The Tenderer is required to prepare two sealed envelope super scribed as (i) envelope -I-Technical Bid, and (ii) envelope-II –Financial Bid. Both envelopes should be kept in one main sealed envelope super scribed as “Tender for Supply of Indian Implants for Orthopaedics at AIIMS Bhopal due on 10.03.2015”.
5. The tenderer has to drop the envelope sealed in above manner in the Tender Box kept at the Office of the Store
Officer, 1st
Floor, E-Wing, Medical College Building, AIIMS Bhopal, Saket Nagar-462020 (MP) on or before 10.03.2015 by 14.00 Hrs. positively. The tender shall not be accepted beyond the stipulated date and time under any circumstances whatsoever.
6. The Technical bid will be opened on the same day at 15.00 hrs by a Committee constituted by the competent
authority of AIIMS Bhopal, in its office in the presence of the Tenderers or their authorised representative who wish to be present. The date and time for opening of Financial Bids of the technically qualified Tenderers shall be communicated later as per convenience of this office.
7. The Authority reserves the right to reject/cancel any or all the tenders at any time or to relax/amend/withdraw any
of the terms and conditions as contained in the Tender Documents without assigning any reason, thereof. Any inquiry after submission of the tender will not be entertained.
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 6 of 62
8. Bidders shall not approach for refund of EMD till the finalization of the tendering process and award of contract to qualifying Tenderer. The offer should remain valid for a minimum period of 120 days. EMD shall be refunded to the unsuccessful bidders within 30 days of award of contract to the successful bidder/bidders.
9. AIIMS Bhopal reserves the full rights to increase/decrease the quantity of items in the tender as per requirement.
10. Any dispute is subject to the jurisdiction of Civil Court Bhopal.
11. The Tender Document has been divided into the following chapters:-
• Chapter-1: General Instructions to Bidders (Page No.7 to 8) • Chapter-2: Terms and Conditions of Contract (Page No.9 to 10) • Chapter-3: Schedule of Requirements & Technical Specifications (Page No. 11 to 27) • Chapter-4: Technical Bid ( Page No. 28 to 30) and Certificate (Page No. 31) • Chapter-5: Check List (Page No. 32) • Chapter-6: Contract Agreement Form (Page No. 33 to 35 ) and Performance Bank Guarantee Form (Page
No.36) • Chapter-7: Financial Bid (to be utilized by the bidders for quoting their prices and price bid should be kept
in separate sealed envelope superscripted as Financial Bid for Supply of Orthopaedics Indian Implants) (Page No. 37-62)
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 7 of 62
Chapter – I
GENERAL INSTRUCTIONS TO BIDDERS 1. The Tenderer must fulfil the following specifications/conditions:-
(a) The tenderer should have its own Bank Account, PAN, TAN, TIN, VAT and Service Tax Number, Gumashta Licence for issued by Nagar Nigam. Payment will be made electronically only under NEFT/RTGS System & Banking transaction required to be quoted.
(b) The rates are to be quoted on FOR-Destination inclusive of all taxes only. However, their breakup is necessary.
(c) The offer of Tenderers quoting rates as per Technical Specifications laid down in Schedule of Requirement and Technical Specifications (Chapter-3).
Description Group 1 Bidder should have average annual financial turnover of Rs. 7.5 LAKH in Hospital
Equipment/Instruments supply works, during the last three Financial Years ending 31st
March 2014 and should not have incurred loss in last 3 years. A letter duly signed by the Chartered Accountant/Company Secretary indicating the Financial Turnover and Profit & Loss Account must accompany with Technical Bid.
i) Should have satisfactorily completed Similar Single Work of Rs. 8 Lakh OR
ii) Should have satisfactorily completed Two Similar works each costing Rs. 6 Lakh OR
iii) Should have satisfactorily completed Three Similar Works each costing Rs. 4 Lakh
Group 2 Bidder should have average annual financial turnover of Rs. 3.3 LAKH in Hospital Equipment/Instruments supply works, during the last three Financial Years ending 31
st March
2014 and should not have incurred loss in last 3 years. A letter duly signed by the Chartered Accountant/Company Secretary indicating the Financial Turnover and Profit & Loss Account must accompany with Technical Bid.
i) Should have satisfactorily completed Similar Single Work of Rs. 3.5 Lakh OR
ii) Should have satisfactorily completed Two Similar works each costing Rs. 2.5 Lakh OR
iii) Should have satisfactorily completed Three Similar Works each costing Rs. 2 Lakh
Group 3 Bidder should have average annual financial turnover of Rs. 3.5 LAKH in Hospital Equipment/Instruments supply works, during the last three Financial Years ending 31
st March
2014 and should not have incurred loss in last 3 years. A letter duly signed by the Chartered Accountant/Company Secretary indicating the Financial Turnover and Profit & Loss Account must accompany with Technical Bid.
i) Should have satisfactorily completed Similar Single Work of Rs. 4 Lakh OR
ii) Should have satisfactorily completed Two Similar works each costing Rs. 3 Lakh OR
iii) Should have satisfactorily completed Three Similar Works each costing Rs. 2 Lakh
Group 4 Bidder should have average annual financial turnover of Rs. 5.8 LAKH in Hospital Equipment/Instruments supply works, during the last three Financial Years ending 31
st March
2014 and should not have incurred loss in last 3 years. A letter duly signed by the Chartered Accountant/Company Secretary indicating the Financial Turnover and Profit & Loss Account must accompany with Technical Bid.
i) Should have satisfactorily completed Similar Single Work of Rs. 6.7 Lakh
OR ii) Should have satisfactorily completed Two Similar works each costing Rs. 5 Lakh
OR iii) Should have satisfactorily completed Three Similar Works each costing Rs. 3.3 Lakh
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 8 of 62
(d) The tenderer should submit the previous work orders showing clear values from the concerned organisation etc. (e) The tenderer should give an Affidavit duly Notarized on Stamp Paper worth Rs. 100/- in clear and un-ambiguous
language that it has never been black listed/no criminal case pending by any of the organisation with whom, it had dealing for supply of similar items during last five years nor has been penalized for inferior or poor quality in supply.
(f) The tenderer should be financially sound and in a position to carry out any other additional supply work order on
approved L-1 Rates under this Rate Contract as per the need of AIIMS Bhopal on a short notice. (g) The Director, AIIMS Bhopal reserves the right to reject any or all tenders without assigning any reasons whatsoever.
Admin Officer
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 9 of 62
Chapter -2
TERMS AND CONDITIONS 1. This rate contract is of initial validity for Supply of Indian Implants for Orthopaedics at AIIMS Bhopal for a period of one
year from the date of award of contract or as indicated in the Rate Contract Agreement. The contract may be extendable year to year subject to a maximum period of 1 year), on the same terms and conditions or as may be agreed mutually by both the parties under the prevailing circumstances.
ELIGIBILITY/EVALUATION CRITERIA (a) The amount of Earnest money deposit (EMD) is item wise of Group-1: 21,700/- , Group-2: 9,605/-, Group-3:
10,030/-, Group-4: 16,800/- (Non-Interest bearing). This Earnest money deposit is compulsory and equal to all the prospective bidders, whether they are bidding for single Item or all the items as per the requirement list given in Chapter-7 of this Tender Enquiry Document by any bidder want to participate in this Tender. The Bidder is required to deposit earnest money along with their Technical Bid document in Technical Bid Envelope in the form of Banker’s Cheque/Demand Draft (Non-Interest Bearing)/FDR from any Nationalized Bank and the same should be drawn in favour of “Director, AIIMS Bhopal” payable at Bhopal.
(b) The successful Tenderer shall have to deposit a Performance Security @10% of order value on each occasion in
the form of FDR/Bank Guarantee in favour of “Director, AIIMS Bhopal” Payable at Bhopal. If Bidder interested to furnish the Performance Security in the way of Bank Guarantee, the Format enclosed at Chapter-6 for reference). The performance security should remain valid for a period of Ninety days beyond the date of completion of all contractual obligations including 36 Months warranty (i.e. for 39 months from the date of Purchase Order). In case, the contract is further extended beyond the initial period of one year, the Performance Security Bank Guarantee shall have to be renewed accordingly and its extension shall be communicated at the time of award of addendum of contract. Earnest Money Deposit shall be refunded to the successful bidder on receipt of performance security.
(c) The Tenderer should give an affidavit duly notarized on Stamp paper worth Rs. 100/-, there in clearly and un-
ambiguously mentioning that it has neither been black listed/no criminal case is pending against him by any of the Govt. Institute/Ministries/Departments/PSU with whom, it had contract for Supply of Indian Implants for Orthopaedics at AIIMS Bhopal etc. during last two years nor has been penalized by such organization on account of poor/spurious quality/after sales services.
(d) The tenderer is advised to submit the desired papers/documents with their technical bid as per the Check List indicated in Chapter-5 failing which their bids shall be declared un-responsive.
OTHER ESSENTIAL TERMS & CONDITIONS:-
2. The selected tenderer would be required to arrange Supply of Indian Implants for Orthopaedics department at AIIMS
Bhopal as per the Despatch Instructions/Purchase cum Supply Order during the working hours of the Institute. Since the rates are to be quoted on destination (at any place in AIIMS Bhopal) complete job basis, no other charges whatsoever are payable extra by AIIMS Bhopal to any successful Tenderer.
3. The selected tendering Firm/Agency/Company shall also provide the name and mobile number of a key person, who can
be contacted at any time, even beyond the office hours and on holidays.
4. Purchase Order shall be issued on requirement basis. Bills in triplicate for the items supplied & put to the working conditions may be part of the work & satisfaction of the competent authority, by the selected firm(s) should be raised for payment. Payment shall be released after deducting TDS as per Income Tax Rules and any other deductions as per Government rules and payment shall be released only after it is ensured that the items/quantity and quality of items supplied are to the entire satisfaction of this office. If any item is found to be defective, or not of the desired quality etc., the same shall be replaced immediately, for which no extra payment shall be made by AIIMS Bhopal.
5. Quality of Goods and Services: The equipment/product must confirm to the Technical specifications given in Chapter-3
and of desired quality. The bidder shall guarantee that item delivered to the purchaser are brand new and not refurbished one. Consistency in quality shall be maintained for the entire lot of products offered.. The vendor shall be responsible for the quality of supply.
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 10 of 62
6. Delivery: Within 30 working days from the date of confirmed purchase Order/Purchase Instruction issued by the
Competent Authority of AIIMS Bhopal to AIIMS Bhopal at Saket Nagar, Bhopal-462 020 (MP).
7. If the selected firm fails to deliver the items or replace the defected/spurious items within the stipulated date & time, a penalty on a weekly basis for delay @ 1% on per week basis, subject to maximum of @10% of total Order Value as penalty and the actual cost paid to be an outside agency by the All India Institute of Medical Sciences (AIIMS) Bhopal after made deduction from the firm’s pending bills or Performance Security, as the case may be.
8. All India Institute of Medical Sciences (AIIMS) Bhopal shall be the sole authority to cancel or amend the order, as per requirement, and also to place order for supply of items beyond office hours/holidays/place of supply for which, no additional payment shall be made.
9. The bills raised by the selected tendering Firm/Agency/Company should have all tax registration numbers printed on bill. The bill shall be signed by the authorized signatory of the firm across a revenue stamp. Validity of the tax registration during the currency of contract shall be the sole responsibility of the tendering Firm/Agency/Company. The bill shall be raised indicating permissible taxes separately and the copies of proof of Service Tax/VAT or other applicable taxes deposited to Tax Authorities by the firm for recent period, just before the submission of Bills must also be enclosed for reference of AIIMS Bhopal authorities.
10. The tendering Firm/Agency/Company shall be bound by the details furnished by him/her to the All India Institute of Medical Sciences (AIIMS) Bhopal while submitting the tender or at subsequent stage. Upon selection of the tendering Firm/Agency/Company, if at any stage, the documents furnished by him/her is found to be false or the quality of the articles or rates are found of poor quality/ different Technical Specifications, it would be deemed to be a breach of terms of contract, the contract shall be cancelled and performance security shall be stand forfeited.
11. The rate quoted by the selected tendering Firm/Agency/ Company, and as approved by the All India Institute of Medical Sciences (AIIMS) Bhopal, shall remain valid throughout the period of contract i.e. 1 year and the request to increase the rates for any or all items, during the currency of contract, shall not be entertained at any stage.
12. The selected firm(s) shall not be allowed to transfer, assign, pledge or sub-contract its rights and liabilities under this contract to any other agency (ies) without prior written consent of the All India Institute of Medical Sciences (AIIMS) Bhopal. If it is found that the firm has given sub-contract for Supply of Indian Implants for Orthopaedics department on the basis of procurement/ supply order, the contract shall stand cancelled & the performance security shall stand forfeited.
13. The conditional/incomplete bids shall not be considered and shall be declared un-responsive. 14. All entries in the tender form should be legible and filled clearly in the published in the Financial Bid Form (Chapter-7)
only. If the space furnishing the information is found insufficient, a separate sheet duly signed by the authorized signatory may be attached. No overwriting or cutting or other than issued forms is permitted in the bid forms. In such cases, the tender shall be declared un-responsive.
15. The tender documents should be sealed and clearly super-scribed with the words “Tender for Supply of Indian Implants for Orthopaedics department at AIIMS Bhopal at AIIMS Bhopal”.
16. Any complementary scheme offered by the manufacturer shall be provided to the All India Institute of Medical Sciences (AIIMS) Bhopal with no additional cost.
(Authorized Signatory)
All Terms and Conditions Read & Signed by me
Signature: ......................................................................................... Name of Tenderer........................................................................ Rubber Stamp..................................................................................
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 11 of 62
Chapter – 3
Schedule of Requirement and Technical Specifications
1. The supply order may be given to the approved L-1 Agency and Agency will have to supply the same immediately but not later than the period as stipulated in the Despatch Instructions/Purchase cum Supply Order at the specified location intimated by the Competent Authority of AIIMS Bhopal.
2. The items will be supplied at the destination location (Place) as stated in the Despatch Instructions/Purchase cum Supply Order/Intimated after receiving Material by Competent Authority at AIIMS Bhopal.
3. All India Institute of Medical Sciences (AIIMS) Bhopal shall be the sole authority to cancel/amend any order, as per
requirement, and also to place order for Supply of Indian Implants for Orthopaedics department at AIIMS Bhopal beyond office hours/holidays/place of supply and Installation for which, no additional payment shall be made.
Indian implants of good quality manufactured by reputed Indian Firms with National Distributorship should apply. Implants should be ISO 9001‐2000 certified Bureau of Indian Standard (BIS) approved/ equivalent certification and must bear the trade mark/logo of the manufacturing firm. Only unit price of the required items is to be quoted. The supplier should provide the Instrumentation set, gratis, for these implants whenever required. The supplier should appear for the demonstration of their implants, if required. The supplier has to quote for each complete set. The price of each item should be quoted separately. L1 will be determined for each set as one basket.
Item S. No.
Item Name Quantity
Group -1 (Set-1,2,3,4,9 ) Set 1 Stainless Steel Plates and Screws Set
1 Stainless Steel Plates (4.5mm) and Screws Set
1.1. Stainless Steel Plates (4.5mm) and Screws Set
1.1.1. Dynamic Compression Plates (Narrow) ‐ 6 holes ‐12 holes 10
1.1.2. Dynamic Compression Plates (Broad) ‐ 6 holes‐18 holes 10
1.1.3. Semi Tubular Plates ‐ 6 holes to 12 holes 5
1.1.4. Reconstruction Plates ‐6 holes to 12 holes 5
1.1.5. Cortical Screws (4.5 mm) ‐ 20 mm to 60 mm 100
1.1.6. Cancellous Screws (6.5mm, fully threaded) ‐ 25mm – 110mm 100
1.1.7. Cancellous Screws (6.5 mm, partially threaded) ‐ 25mm‐100mm
1.2. Stainless Steel Plates (3.5mm) and Screws Set
1.2.1. Dynamic Compression Plates ‐ 4 holes to 10 holes 10
1.2.2. Limited Contact-Dynamic Compression Plates (LC-DCP) ‐ 4 holes to 10 holes 10
1.2.3. 1/3 Tubular Plates ‐ 4 holes to 10 holes 5
1.2.4. Reconstruction Plate‐ 4 holes to 10 holes 5
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 12 of 62
1.2.5. Cortical Screws (3.5mm) – 8mm to 24mm 100
1.2.6. Cancellous Screws (4.0 mm, fully threaded) ‐ 10mm‐50 mm 100
1.2.7. Cancellous Screws (4.0 mm, partially threaded) ‐ 20mm‐50 mm 100
1.3. Peri-Articular Plates (4.5mm and 3.5mm) and Screws Set
1.3.1. T-Plates (4.5mm) – 4 holes to 12 holes 5
1.3.2. L-Plates (4.5mm)– 4 holes to 12 holes 5
1.3.3. L-Plates (3.5mm)– 3 holes to 6 holes 5
1.3.4. Buttress Plates (4.5mm) – 4 holes to 12 holes 5
1.3.5. Cortical screws – 20 mm– 60mm 100
1.3.6. Cancellous screws, (6.0mm/4.0mm), fully threaded – 25 mm– 110 mm 50
Set 2
2 Titanium Plates and Screws Set
2.1. Titanium Plates (4.5mm) and Screws Set
2.1.1. Dynamic Compression Plates (Narrow) ‐ 6 holes ‐12 holes 10
2.1.2. Dynamic Compression Plates (Broad) ‐ 6 holes‐18 holes 10
2.1.3. Semi Tubular Plates ‐ 6 holes to 12 holes 5
2.1.4. Reconstruction Plates ‐6 holes to 12 holes 5
2.1.5. Cortical Screws (4.5 mm) ‐ 20 mm to 60 mm 100
2.1.6. Cancellous Screws (6.5mm, fully threaded) ‐ 25mm – 110mm 50
2.1.7. Cancellous Screws (6.5 mm, partially threaded) ‐ 25mm‐100mm 50
2.2. Titanium Plates (3.5mm) and Screws Set
2.2.1. Dynamic Compression Plates ‐ 4 holes to 10 holes 10
2.2.2. Limited Contact-Dynamic Compression Plates (LC-DCP) ‐ 4 holes to 10 holes 5
2.2.3. 1/3 Tubular Plates ‐ 4 holes to 10 holes 5
2.2.4. Reconstruction Plate‐ 4 holes to 10 holes 5
2.2.5. Cortical Screws (3.5mm) – 8mm to 24mm 100
2.2.6. Cancellous Screws (4.0 mm, fully threaded) ‐ 10mm‐50 mm 50
2.2.7. Cancellous Screws (4.0 mm, partially threaded) ‐ 20mm‐50 mm 50
Set 3
3 Titanium Locking Compression Plates and Screws Set
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 13 of 62
3.1. Locking Compression Plates (4.5 mm)
3.1.1. Locking Compression Plates, Narrow, 6 holes ‐16 holes 10
3.1.2. Locking Compression Plates, Broad, 6 holes ‐ 18 holes 10
3.1.3. T‐Plate Locking Compression Plates, 3 holes to 8 holes 5
3.1.4. T‐Buttress Locking Compression Plates, 4 holes to 6 holes 5
3.1.5. L‐Buttress Locking Compression Plates, left / right, 3 holes to 6 holes 5
3.1.6. Locking Reconstruction Plates, 5 holes ‐ 16 holes 5
3.1.7. Cortical Screws, 4.5 mm, length ‐ 14 mm to 90 mm 100
3.1.8. Cancellous Screws, 6.5mm, 16mm threaded, length 30 mm – 120 mm 50
3.1.9. Cancellous Screws, 6.5 mm, 32mm threaded25mm‐110mm 50
3.1.10. Cancellous Screws, 6.5 mm, fully threaded 25mm‐110mm 50
3.1.11. Locking screws – 14 mm – 90 mm 50
3.2. Locking Compression Plates (3.5 mm)
3.2.1. Locking Compression Plates, 3.5 mm, 5 holes – 12 holes 10
3.2.2. Locking T. Plates 3.5mm, right/left/oblique, 6 holes ‐16 holes 5
3.2.3. Locking 1/3 Tubular Plates 3.5 mm, 4 holes to 10 holes 5
3.2.3. Locking Reconstruction Plates, 5 holes – 14 holes 5
3.2.5. Cortical Screws 3.5mm, 8mm to 24mm 100
3.2.6. Cancellous Screws 4.0 mm, fully threaded, 10 mm‐50 mm 50
3.2.7. Cancellous Screws 4.0 mm, partially threaded, 20 mm ‐50 mm 50
3.2.8. Locking screws, 18 mm ‐ 55 mm 50
Set 4
4 Stainless Steel Locking Compression Plates and Screws Set
4.1. Locking Compression Plates (4.5 mm)
4.1.1. Locking Compression Plates, Narrow, 6 holes ‐16 holes 10
4.1.2. Locking Compression Plates, Broad, 6 holes ‐ 18 holes 10
4.1.3. T‐Plate Locking Compression Plates, 3 holes to 8 holes 5
4.1.4. T‐Buttress Locking Compression Plates, 4 holes to 6 holes 5
4.1.5. L‐Buttress Locking Compression Plates, left / right, 3 holes to 6 holes 5
4.1.6. Locking Reconstruction Plates, 5 holes ‐ 16 holes 5
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 14 of 62
4.1.7. Cortical Screws, 4.5 mm, length ‐ 14 mm to 90 mm 100
4.1.8. Cancellous Screws, 6.5mm, 16mm threaded, length 30 mm – 120 mm 50
4.1.9. Cancellous Screws, 6.5 mm, 32mm threaded 25mm – 110mm 50
4.1.10. Cancellous Screws, 6.5 mm, fully threaded 25mm – 110mm 50
4.1.11. Locking screws – 14 mm – 90 mm 50
4.2 Locking Compression Plates (3.5 mm)
4.2.1. Locking Compression Plates, 3.5 mm, 5 holes – 12 holes 10
4.2.2. Locking T. Plates 3.5mm, right/left/oblique, 6 holes ‐16 holes 5
4.2.3. Locking 1/3 Tubular Plates 3.5 mm, 4 holes to 10 holes 5
4.2.4. Locking Reconstruction Plates, 5 holes – 14 holes 5
4.2.5. Cortical Screws 3.5mm, 8mm to 24mm 100
4.2.6 Cancellous Screws 4.0 mm, fully threaded, 10 mm‐50 mm 50
4.2.7. Cancellous Screws 4.0 mm, partially threaded, 20 mm ‐50 mm 50
4.2.8. Locking screws, 18 mm – 55 mm 50
Group -2 (Set-5,6,7,8)
Set 5
5 Interlocking Nails (Stainless Steel)
5.1. For Humerus
5.1.1. Humeral Nails, 6,7, 8mm,190‐310mm 5
Suture holes at proximal end
Two oblique holes proximally
Antero-posterior distal locking
5.1.2. Locking screws – assorted sizes 10
5.1.3. End cap – assorted size 5
5.1.4. Spiral blades – assorted sizes 5
Proximal drill guide should be radiolucent.
Should be supplied Sterile Packed
5.2. For Tibia
5.2.1. Unreamed Tibial Nail
5.2.1.1. Solid nails, bevelled proximal tip, D 8 – 9mm, Length 280‐380mm 5
With proximal transverse holes so that fractures close to the joint spacecan be treated by inserting oblique screws that should not compromisethe Tibial plateau posteriorly.
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 15 of 62
Proximal Dynamic slot to allow compression
Further distal hole to treat distal metaphyseal fractures
Should be supplied Sterile Packed
Proximal Drill guide should be radiolucent.
5.2.1.2. End caps, assorted sizes 5
5.2.1.3. Locking bolts, assorted sizes 10
5.2.2. Reamed Tibial Nail 10
5.2.2.1. Cannulated nail, 8 - 10mm, 300‐360mm
Bevelled proximal end, tapered distal tip
Two slots at both ends for locking
5.2.2.2. Locking bolts/end cap assorted sizes 10
5.3. For Femur
5.3.1. Antegrade Femoral Interlocking Nail 5
5.3.1.1. Femoral Nails ‐ 8mm to 14mm, Length 24 cm to 46cm
5.3.1.2. Hip Screws, 6.5mm, 60mm to 130mm 10
5.3.1.3. Low Profile Cortical Locking Bolts ‐ 4.2mm, 20mm to 90mm 10
Suitable for interlocking and reconstruction purposes
With facility for dynamization
Nail should be cannulated
Should be supplied Sterile Packed
Proximal Drill Guide should be radiolucent.
5.3.2. Retrograde Femoral Interlocking Nail
5.3.2.1. Femoral Nails, 9 ‐ 14mm, 160mm to 420mm 5
5.3.2.2. Spiral blades – 60 – 80 mm 5
5.3.2.3. Locking bolts and end cap – assorted sizes 5
With Dynamic slot
Three closely located distal holes for Supracondylar fracture
Five Degree Distal Bend to accommodate Inter-condylar notch
Should be supplied Sterile Packed
Drill guide should be radiolucent.
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 16 of 62
Set 6
6 Interlocking Nails (Titanium)
6.1. For Humerus
Humerus interlocking nail
Provisions for high proximal and low distal fracture fixations
6.1.1. Sizes: 6.7mm to 9.5mm, length 190mm to 310mm 5
6.1.2. Locking Screws 3.9mm 16mm to 60mm 5
6.1.3. Bolts/end cap 5
6.2. For Tibia
6.2.1. Unreamed Tibial Nail
Should have anatomical shape with anti-curvature and lateralization
Nail should be Solid/Cannulated
9 ‐ 11° bend in the proximal part
The runner shaped Tapered tip
Locking options proximally 2 medio-lateral and one dynamization slot,distally 2 medio-lateral , 2 anterio-posterior, the last slot should not bemore than 10mm away from distal tip.
6.2.1.1. Sizes : 8 ‐10mm, length 240 to 420mm 5
6.2.1.2. Endcaps 0 to 25mm 5
6.2.2. Reamed Tibial Nail
Should have anatomical shape with anti-curvature and lateralization.
The Nail should be cannulated.
9 ‐ 11° bend in the proximal part.
The runner shaped Tapered tip
Locking options proximally 2 medio-lateral and one dynamization slot,distally 2 medio-lateral , 2 anterio-posterior, the last slot should not bemore than 10mm away from distal tip.
6.2.2.1. Sizes : 8 ‐10mm, length 240 to 420mm 10
6.2.2.2. End-caps 0 to 25mm 5
6.2.3. Tibial Nail for metaphyseal and diaphyseal fractures
Anatomically contoured nail, cannulated nail
Multiple locking options at both ends of nail
Multi directional proximal slots with provision for standard/ cancellouslocking screws
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 17 of 62
6.2.3.1. Nail – 8mm‐10 mm, 280mm‐ 410mm 5
6.2.3.2. Locking screws – 4.0mm, 16mm‐64mm 5
6.2.3.3. Locking screws – 5.0mm, 24mm‐64mm 10
6.2.3.4. End cap – 0 to 18mm 5
6.3. For Femur
6.3.1. Antegrade Femoral Interlocking Nail
6.3.1.1. Femoral Nails ‐ 8mm to 14mm, length 240 to 460mm 5
6.3.1.2. Reconstruction Screws, 5.5mm, 60mm to 130mm 5
6.3.1.3. Low Profile Cortical Locking Bolts ‐ 4.2mm, 20mm to 90mm 5
Suitable for interlocking and reconstruction purposes
With facility for dynamization
Nail should be cannulated
Should be supplied Sterile Packed
Proximal Drill Guide should be radiolucent.
6.3.2. Retrograde Femoral Interlocking Nail
6.3.2.1. Femoral Nails, 10 ‐ 14mm, 160mm to 420mm 5
6.3.2.2. Locking bolts, end cap 5
With Dynamic slots
Three closely located distal holes for Supracondylar fracture
Five Degree Distal Bend to accommodate Inter-condylar notch
Should be supplied Sterile Packed
Drill guide should be radiolucent.
6.3.3. Proximal Femoral Interlocking Nail
Anatomically designed for femur
Two locking options for neck
Safety provision to prevent screw slippage into femoral neck
Option for de-rotational hip pin
Distal slot with options of static/dynamic locking
6.3.3.1. Nail ‐ 10‐ 11mm,200 – 420mm 5
6.3.3.2. Neck screw – 11mm, 80 – 110mm 5
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 18 of 62
6.3.3.3. Hip pin – 6.5mm, 75‐100mm 5
6.3.3.4. Locking bolts/end cap – assorted size 5
Set 7
7 Condylar Blade Plate, DHS & DCS set
7.1. 95° Condylar Blade Plate
7.1.1. Plate Sizes 5 to14 Holes 5
7.1.2. Blade Length 50 – 80mm
7.2. DHS & DCS set
DHS Plates ‐ 135deg – 150 deg
5
7.2.1. L 46 – 270mm, 2 to 16 holes 5
7.2.2. Barrel L 25 – 38mm
DCS Plates – 95 deg
7.2.3. L114 – 370mm, 6 – 22 holes 5
7.2.4. Barrel L 25mm
DHS/DCS Screws
7.2.5. L 65 – 110mm, Thread L 22mm 5
7.2.6. Compression Screw – 36mm 5
Set 8
8 Nails, and Wires -Stainless steel
8.1. Kirschner (K‐) Wires
8.1.1. 1.0mm diameter, with trocar tip, L 150mm 100
8.1.2. 1.2mm diameter, with trocar tip, L 150mm 100
8.1.3. 1.5mm diameter, with trocar tip, L 150mm 250
8.1.4. 2.0mm diameter, with trocar tip, L 150mm 100
8.2. Kuntscher – Nails
8.2.1. Assorted sizes 10
8.3. Steinmann Pins
8.3.1. 3.5mm – 4.5mm 50
Trocar tip; Assorted sizes
8.4. Wire Sutures
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 19 of 62
8.4.1. 18G to 22G 5
Set 9
9 Screws, Drill Bits, and Bone Taps
Screws – Should be provided with 2 screw-drivers for each type
9.1.1. 7.3 mm Cancellous Screw
9.1.1.1. Deep cancellous thread with reverse cutting flutes
9.1.1.2. Threaded 16 mm, 40 mm to 120 mm 50
9.1.1.3. Threaded 32 mm, 50 mm to 150 mm 50
9.1.2. 6.5 mm Cancellous Screw (Stainless Steel)
9.1.2.1. Threaded 16 mm, 30 mm to 120 mm 50
9.1.2.2. Threaded 32 mm, 45 mm to 150 mm 50
9.1.2.3. Fully threaded 20 mm to 110 mm
9.1.3. 6.5 mm Cancellous Screw (Titanium)
9.1.3.1. Threaded 16 mm, 30 mm to 120 mm 50
9.1.3.2. Threaded 32 mm, 45 mm to 150 mm 50
9.1.3.3. Fully threaded 20 mm to 110 mm 50
9.1.4. 4.5 mm Malleolar Screw
9.1.4.1. 4.5 mm Malleolar Screws (Stainless Steel) 10
9.1.4.2. Head & Core D 8 mm x 3 mm
9.1.4.3. L25 mm to 70 mm
9.1.4.4. Thread D 12 to 32 mm
9.1.5. Cortex Screw 3.5 mm
9.1.5.1. 3.5 mm Cortex Screws (Stainless Steel)
9.1.5.2. 10 mm to 40 mm 100
9.1.5.3. 3.5 mm Cortex Screw (Titanium)
9.1.5.4. 10 mm to 90 mm 50
9.2. Cannulated Screws – should be supplied with complete instrumentation
9.2.1. 4.0mm Cannulated screw set
9.2.1.1. 4.0mm cannulated 316L stainless steel 25
Partially threaded, L 14 -30 (2mm increment), 35-75 (5mm increment)
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 20 of 62
9.2.1.1.1. Fully threaded, L 14 -30 (2mm increment), 35-75 (5mm increment) 10
9.2.1.1.2. Washer 7mm 5
9.2.1.2. 4.0mm cannulated Titanium alloy
9.2.1.2.1. Partially threaded, L 14 -30 (2mm increment), 35-75 (5mm increment) 10
9.2.1.2.2. Fully threaded, L 14 -30 (2mm increment), 35-75 (5mm increment) 10
9.2.1.2.3. Washer 7mm 5
9.2.2. Cannulated headless compression screw set (Herbert-Whipple type)
Should be made up of Titanium alloy
9.2.2.1. 3.5mm Diameter Screw
Length (mm): 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30
10
9.2.2.2. 4.5mm Diameter Screw
Length (mm): 14, 16, 18, 20, 22, 24, 26, 28, 30
5
9.2.2.3. 6.5mm Diameter Screw
Length (mm): 14, 16, 18, 20, 22, 24, 26, 28, 30
5
9.3. Drill Bits
9.3.1. Drill bit 4.5 mm 2
D 4.5 mm x L 147 mm
Thread L 120 mm
9.3.2. Drill bit 4.5 mm 2
D 4.5 mm x L 130 mm
Thread L 115 mm
9.3.3. Drill bit 4.5 mm 2
D 4.5 mm x L 195 mm
Thread L 170 mm
9.3.4. Drill bit 4.5 mm 2
D 4.5 mm x L 180 mm
Thread L 165 mm
9.3.5. Drill bit 3.5 mm 2
D 3.5 mm x L 100 mm
Thread L 85 mm
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 21 of 62
9.3.6. Drill bit 3.5 mm 2
D 3.5 mm x L 195 mm
Thread L 170 mm
9.3.7. Drill bit 3.5 (Cannulated) 2
D 3.5/1.35 mm x L 160/130 mm
9.3.8. Drill bit 3.2 mm 2
D 3.2 mm x L 225 mm
Thread L 200 mm
9.3.9. Drill bit 3.2 mm 2
D 3.2 mm x L 180 mm
Thread L 165 mm
9.3.10. Drill bit 3.2 mm 2
D 3.2 mm x L 145 mm
Thread L 120 mm
9.3.11. Drill bit 3.2 mm 2
D 3.2 mm x L 130 mm
Thread L 115 mm
9.3.12. Drill bit 2.8 mm 2
D 2.8 mm x L 165 mm
9.3.13. Drill bit 2.7 mm 2
D 2.7 mm x L 100 m
Thread L 75 mm
9.3.14. Drill bit 2.7 mm 2
D 2.7 mm x L 85 mm
Thread L 70 mm
9.3.15. Drill bit 2.7 mm 2
D 2.7 mm x L 125 mm
Thread L 100 mm
9.3.16. Drill bit 2.7 (Cannulated) 2
D 2.7/1.35 mm x L 160/130 mm
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 22 of 62
9.3.17. Drill bit 2.5 mm 2
D 2.5 mm x L 95 mm
Thread L 70 mm
9.3.18. Drill bit 2.5 mm 2
D 2.5 mm x L 112 mm
Thread L 85 mm
9.3.19. Drill bit 2.0 mm 2
D 2.0 mm x L 102 mm
Thread L 75 mm
9.3.20. Drill bit 2.0 mm 2
D 2.0 mm x L 85 mm
Thread L 70 mm
9.3.21. Drill bit 2.0 mm 2
D 2.0 mm x L 125 mm
Thread L 100 mm
9.3.22. Drill bit 1.5 mm 2
D 1.5 mm x L 70 mm
Thread L 55 mm
9.3.23. Drill bit 1.5 mm 2
D 1.5 mm x L 85 mm
Thread L 60 mm
9.3.24. Drill bit 1.5 mm 2
D 1.5 mm x L 110 mm
Thread L 85 mm
9.3.25. Drill bit 1.1 mm 2
D 1.1 mm x L 45 mm
Thread L 30 mm
9.3.26. Drill bit 1.1 mm 2
D 1.1 mm x L 60 mm
Thread L 35 mm
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 23 of 62
9.4. Bone Taps
9.4.1. 2.7mm 4
9.4.2. 3.5mm 4
9.4.3. 4mm 4
9.4.4. 4.5mm 4
9.4.5. 5mm 2
Group -3 (Set-10,11,13,14)
Set 10
10 Implants for Hip Arthroplasty
10.1. Austin Moore Prosthesis for hip
10.1.1. Head size 39mm – 55mm 10
10.2. Bipolar hip prosthesis Non-Modular (mono-block)
10.2.1. Size 39 to 53 10
Cemented and cementless
10.3. Bipolar hip prosthesis Modular 5
Should consist of
10.3.1. Femoral stem
10.3.2. Acetabular head
10.3.3. Bipolar cup with liner
10.3.4. Bone cement low viscosity 2 packets (40grams each)
10.3.5. Cement restrictor 8mm‐ 14mm
Set 11
11 Arthroscopic Implants for Knee and Shoulder Joints
11.1. Trans Fixation Pin (Titanium)
3mm‐5mm x 45mm‐50mm
5
11.2. Trans Fixation (Stainless steel)
4mm‐5mm x 45mm‐50mm
5
11.3. Interference Screws (Titanium)
Cannulated
7mm‐11mm x 20mm‐35mm
5
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 24 of 62
11.4. Interference Screws (Stainless steel) 5
11.5. Interference Screws (Bio-absorbable) 5
Round head, Cannulated
7mm‐ 1.0mm x 20mm‐ 35mm
11.6. Ligament Staple (Titanium) 5
8mm ‐ 20mm x 11mm ‐ 20mm
11.7. Ligament Staple (Stainless steel) 5
8mm ‐ 20mm x 11mm ‐ 20mm
11.8. Endo Buttons (Titanium) 5
3mm‐4mm x 9mm‐18mm
11.9. Endo Buttons (Stainless steel) 5
3mm‐4mm x 9mm‐18mm
11.10. Suture Washers/Disc (Titanium) 5
For graft fixation, 12mm‐ 18mm x 12mm‐ 20mm
11.11. Suture Washers / Disc (Stainless steel) 5
For graft fixation, 12mm‐ 18mm x 12mm‐ 20mm
11.12. Suture post (Titanium) 5
Flat head, Low profile screw
7mm‐ 10mm x 20mm‐ 35mm
11.13. Suture Anchors (Titanium) 5
2.3mm to 6.8mm
11.14. Arthroscopic Electrodes 2
Compatible with bipolar cautery consoles
90°, L‐ Hook
Group -4 (Set-12)
Set 12
12 Custom made Implants for Tumour Surgery
Material: Cobalt-Chrome alloy
Cost of extenstion block/ segment should be mentioned separately for each category
12.1. Custom Made Prosthesis for Distal Femur 2
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 25 of 62
Assorted sizes
12.2. Custom Made Prosthesis for Proximal Tibia 2
Assorted sizes
12.3. Custom Made Prosthesis for Proximal Femur 2
Assorted sizes
12.4. Custom Made Prosthesis for Proximal Humerus 2
Assorted sizes
Set 13
13 Implants for Spinal Surgery
Implants compatible with Indian titanium Instrumentation
The Screw Design should be compatible with 5mm Rod.
It should have Innie / Outie and Single Lock option with torque device available.
It should be compatible with Moss-Miami Instrumentation.
It should have an option of Minimally Invasive Spine Surgery also.
13.1. The Screws should be available in assorted diameter like 4.5mm, 5mm, 6mm, 7mm 20
13.2. The Screws should be available in assorted length of 25, 30, 35, 40, 45 and 50mm
13.3. Axial Connector 4/5 and 5/5. 20
13.4. Transverse Connector 10
13.5. Tapered Rod 3/4/5mm, and 4/5mm
13.6. Titanium Rod 5 mm x 480 mm 10
13.7. Hooks- Laminar, pedicular, Offset
13.8. Pelvic/ Iliac screws and pelvic fixation devices
13.9. Long screws
13.10. Reduction screws 5
13.11. Vertical titanium Mesh Cages (all sizes) 2
13.11.1. Titanium Mesh 18, 22, 28mm (varied lengths)
13.11.2. Titanium Mesh Size 13 X 70mm
13.11.3. Titanium Mesh Size 16 X 60mm
13.11.4. Titanium Mesh Size 19x 90mm
13.11.5. Titanium Mesh Size 10 x 100mm
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 26 of 62
13.11.6. Titaniumlordotic mesh 13 x 130 curved
13.11.7. Mesh 22x28mm Oval 15mm Height
13.11.8. Mesh 22x28mm Oval 50mm Height
13.11.9. Mesh 22x28mm Oval 70mm Height
13.11.10. Mesh 22x28mm Oval 90mm Height
13.11.11. Mesh 26x35mm Oval 90mm Height
13.12. Carbon Cages – Banana shaped – all sizes
13.13. Expandable Titanium cages – assorted sizes 1
13.14. Staples should be made from original titanium in four prong design. 5
The staple should be universal designed to cross the screw of various diameter sizes i.e. 4.5mm, 5mm, 6mm, and 7mm.
13.15. The double-hole staple should be made in various types like small, medium, large and extra-large.
It should be double-hole 4 prong.
It should have single-hole 3 prong.
The original open implant should be made available for demonstration at the time oftechnical evaluation.
Set 14
14 External Fixation Set
14.1. Tubular External Fixator System (in different combination as required) Stainless Steel
14.1.1. Universal Clamp 10
14.1.2. Rods D 11mm, Length 6” to 16” 10
14.1.3. Rod to Rod Clamp 5
14.1.4. Schanz Pin 45 mm cortical 10
14.1.5. Schanz Pin 6.0 mm cancellous 10
14.1.6. Spanner 10/11 10
14.2. Ring Fixator (external) System (in different combination as required)
14.2.1. Stainless steel rings ½ rings – 80 mm to 240 mm 50
14.2.2. Carbon ½ rings 60 – 180 mm 20
14.2.3. Threaded Rod 4” to 14” 10
14.2.4. Italian Arch assorted – 1400, 1600, 1800, 2000 10
14.2.5. Single pin Fixator central slot, side slot 50
14.2.6. Nut – 6 mm 50
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 27 of 62
14.2.7. Oblique Support 5
14.2.8. Female Posts 2 hole, 3 hole, 4 hole 5
14.2.9. Male Posts 2 hole, 3 hole, 4 hole 5
14.2.10. Hinges Male 5
14.2.11. Hinges Female 5
14.2.12. Hinges 90o
5
14.2.13. Short Connection Plates 5‐12 holes 5
14.2.14. Twisted Plates 1‐4 holes 5
14.2.15. Threaded Sockets 5
14.2.16. Olive Wires – 1.8 mm, 1.5 mm 50
14.2.17. K-Wires Trocar tips 1.8 mm, 1.5 mm 100
14.2.18. K-Wires Bayonet tips 1.8mm, 1.5mm 100
14.2.19. Wire Fixation Bolts – cannulated for 1.8mm and 1.5mm 100
14.2.20. Wire Fixation Bolts – slotted for 1.8mm and 1.5mm 100
14.2.21. Connecting Bolts 15 mm, 20 mm, 25 mm 200
14.2.22. Washers 10
14.2.23. Dynamometric tensioner 1
14.2.24. Wire tensioner 2
The supplier should quote his Lowest rate for complete set of group in which he is interested. However it is
necessary to quote rate for each item of such group failing which bid will be treated disqualified. L-1 will
be determined on aggregate basis for each group.
The Technical Bid & Financial Bid should be kept in two separate sealed envelope superscripting
with “Technical Bid for Supply of Indian Implants for Orthopaedics department at AIIMS Bhopal’
and “Financial Bid for Supply of Indian Implants for Orthopaedics department at AIIMS Bhopal’
otherwise the Tenderer bid will be rejected.
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 28 of 62
Chapter – 4
TECHNICAL BID (It is mandatory for all Bidders; they should fill all fields “Clearly” in this form)
1. For the Supply of Indian Implants at All India Institute of Medical Sciences (AIIMS) Bhopal, Saket Nagar,
Bhopal-462024 (MP)
2. Name of Company/Firm/Agency and its
Registration No.
: ___________________________________
3. Name of proprietor / Director of the
Company/Firm/Agency
: ___________________________________
4. Full Address of Reg. Office (A copy of
Company/ Firm/ Agency registration
must be enclosed)
: ____________________________________
____________________________________
Telephone Nos. : ____________________________________
Fax Nos. : ____________________________________
E-mail Id : ____________________________________
5. Details of Banker of the Firm with full
address
: ____________________________________
____________________________________
Telephone Nos. of Banker : ____________________________________
Fax Nos. of Banker : ____________________________________
E-mail Id of Banker : ____________________________________
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 29 of 62
6. Bank Ac/s No. of Firm for ECS payments
RGTS/NEFT
: ____________________________________
7. Gumashta Licence for Nagar Nigam,
PAN, TIN, TAN, VAT, Service Tax
Registration No of the Firm (Enclose a
copy of the same)
: ____________________________________
____________________________________
8. Details of Cost of Tender : ____________________________________
9. Details of EMD : ___________________________________
10. Financial turnover of the tendering Company/Firm Agency for the last three financial years : (Attach
separate sheet if space provided insufficient)
The tenderer should also submit self-attested copies of the Income Tax Returns and Audited certified Accounts for the last three financial years (i.e. for 2010-11, 2011-2012 and 2012-2013). Income Tax return should be of same entity participating in tendering.
11. Give details of major contracts handled by the tendering Company / Firm / Agency for the last three years in the
following format (enclose the self-attested copies):(if the space provided is insufficient, a separate sheet may be attached)
Financial Year Amount (Rs. Lakh) Remarks, if any
2011-2012
2012-2013
2013-2014
S.
No.
Details of client along with
address, telephone numbers
and Fax numbers
Amount of
Contract
(Rs. in Lakh)
Duration of Contract
From To
1
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 30 of 62
(Signature of authorized person) Date :________________________________Full Name:___________________________ Place: ________________________________ Seal: _______________________________
2
3
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 31 of 62
CERTIFICATE
1. I, ____________________________________Son / Daughter / Wife of Shri__________________________________ Proprietor / Director/authorized signatory of the agency/Firm, mentioned above, is competent to sign this declaration and execute this tender document;
2. I have carefully read and understood all the terms and conditions of the tender and undertake to abide by them;
3. The information / documents furnished along with the above application are true and authentic to the best of my knowledge and belief. I / we, am / are well aware of the fact that furnishing of any false information / fabricated document would lead to rejection of my tender at any stage besides liabilities towards prosecution under appropriate law.
4. I, do hereby declare that our firm has neither been blacklisted/no criminal case pending against him (attach an
affidavit duly notarized on Stamp Paper Worth of Rs. 100/-) stating that no criminal/Black listing case is pending against the firm) by any of the Govt. Institute/Ministries/Departments/PSUs with which the firm had contracted for Supply of Indian Implants for Orthopaedics department etc. during the last five years nor has been penalized by such Offices/organizations for supply of poor/spurious equipment’s etc.
(Signature of authorized person)
Date:________________________________ Full Name:___________________________
Place:________________________________ Seal: _______________________________
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 32 of 62
Chapter-5
CHECK LIST OF DOCUMENTS TO BE SUBMITTED ALONG WITH THE TECHNICAL BID and FINANCIAL BID
DOCUMENTS REQUIRED TO BE SUBMITTED WITH TECHNICAL BID:-
1. The Cost of Tender Document enclosed in the form of Demand Draft of Rs. 525/-(Five Hundred Twenty Five Only)
(Non-Refundable)from any Nationalized Bank in favour of “Director, AIIMS Bhopal ”payable at Bhopal and must accompanied with Technical Bid if the tender document downloaded from the website.
2. EMD of Group-1:21,700/- ,Group-2: 9,605/-, Group-3: 10,030/-, Group-4: 16,800/-, in the form of Demand Draft BG/FDR from any Nationalized Bank in favour of “Director, AIIMS Bhopal”, payable at Bhopal and must accompanied with Technical bid.
3. Technical bid Form duly Filled, Signed & Stamped. 4. Tender document each page duly Signed, Stamped and page numbering done. 5. Proof of Office Address. 6. Proof of Bank account Number. 7. Attested Copy of PAN, TAN, TIN VAT, Service Tax Registration Number etc.; 8. Self-attested copies of the IT returns for last 3 Year’s; for 2011-12, 2012-13, 2013-14 9. Audited Certified copies of Accounts for last 3 Year’s; for 2011-12, 2012-13, 2013-14 dully signed by chartered
accountant. 10. The rates for quoted items shall be quoted in the Format given in Financial Bid (Chapter7) and sealed, signed Financial
Bid kept in Financial Bid Envelope separately.
11. Attested copy of Three years’ experience i.e. 2011-12, 2012-13, 2013-14, certificate obtained from Govt. Dept./PSU Concerned.
12. An Affidavit duly Notarized on Stamp Paper worth of Rs. 100/- in clear and un-ambiguous language that the Tenderer
has never been black listed/no criminal case pending by any of the organisation with whom, it had dealing for supply of similar items during last five years nor has been penalized for inferior or poor quality in supply must be accompanied with Technical Bid Envelope.
DOCUMENTS REQUIRED TO BE SUBMITTED WITH FINANCIAL BID
13. The tendering Firm/Agency/Company should quote their Lowest rates for all the items mentioned in concerned group and specification laid down in Financial Bid (Chapter-7), failing which their bids shall be out rightly rejected. Financial Bid must be kept in separate sealed super-scribed envelope “Financial Bid for Supply of Indian Implants for Orthopaedics department at AIIMS Bhopal”.
The tender should be submitted under two bid system. The Interested firms/agencies are advised to submit two separate envelopes super-scribing “Technical Bid for Supply of Indian Implants for Orthopaedics department at AIIMS Bhopal’ and “Financial Bid for Supply of Indian Implants for Orthopaedics department at AIIMS Bhopal’. Both sealed envelopes should be kept in a third bigger sealed envelope super-scribed with the words “Tender for Supply of Indian Implants for Orthopaedics department at AIIMS Bhopal”.
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 33 of 62
Chapter - 6 Contract Form (To be made on Rs 100.00 Non Judicial Stamp/E Stamp Paper)
DRAFT AGREEMENT FORMAT
This agreement is made at Bhopal on the ____________day of ____________ Two Thousand fourteen between
____________________ acting through Shri _________________, _________________, All India Institute of Medical
Sciences(AIIMS) Bhopal, Saket Nagar, Bhopal-462024 (MP)(hereinafter called ‘Client’ which expression shall, unless
repugnant to the context or meaning thereof be deemed to mean and include its successors, legal representatives and
assigns) of the First Part.
SECOND PART
M/s____________________________________________________, having its registered office
at____________________________________________ (hereinafter called the ‘Agency’ which expression unless repugnant
to the context shall mean and include its successors-in-interest assigns etc.) Of the Second Part.
WHEREAS the ‘Client’ is desirous to engage the ‘Agency’ for establishing Supply of Indian Implants for Orthopaedics
department at AIIMS Bhopal as per the terms and conditions stated below:-
1. The Registered Office or Branch Office of the Agency should be located preferably in the Bhopal City. The Agency
should submit a proof of its office address.
2. The selected Agency services would be required to install Supply of Indian Implants for Orthopaedics department items
to All India Institute of Medical Sciences (AIIMS) Bhopal, Saket Nagar, and Bhopal-462024 (MP) on all working days
between 09.00 Hrs. to 17.30 Hrs. No separate charges for delivery of goods would be paid by this office.
3. Order for items shall be placed on requirement basis. Bills in triplicate for the items supplied by the selected Agency
should be raised for payment. Payment shall be released after deducting TDS as per Income Tax Rules and any other
deductions as per Government rules and payment shall be released only after it is ensured that the items/quantity and
quality of items supplied are to the entire satisfaction of this office. If any items are found to be defective, or not of the
desired quality etc., the same shall be replaced by the selected Agency immediately for which no extra payment shall
be made.
4. If the selected Agency fails to deliver Supply of Indian Implants or replace the defected/spurious items within the
stipulated date & time, a penalty on a daily basis for delay @ Rs. 500/- (Five Hundred) on per day basis, subject to
maximum of Rs. 5000/- per item as penalty and the actual cost paid to be an outside agency by the ALL India Institute
of Medical Sciences (AIIMS) Bhopal, for the desired Supply of Indian Implants, shall be deducted from the firm’s
pending bills or Performance Security, as the case maybe.
5. The Agency shall be bound by the details furnished by him/her to the AIIMS Bhopal while submitting the tender or at
subsequent stage. Upon selection of the Agency, if at any stage, the documents furnished by him/her is found to be
false or the quality of the articles or rates are found of poor quality/ different Technical Specifications, it would be
deemed to be a breach of terms of contract, the contract shall be cancelled and performance security shall be stand
forfeited.
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 34 of 62
6. The rate quoted by the selected Agency, and as approved by the AIIMS Bhopal, shall remain valid throughout the
period of contract and the request to increase the rates for any or all items, during the currency of contract, shall not
be entertained at any stage.
7. The selected Agency shall not be allowed to transfer, assign, pledge or sub contract its rights and liabilities under this
contract to any other agency/is without prior written consent of the AIIMS Bhopal. If it is found that the firm has given
sub-contract for Supply of Indian Implants on the basis of procurement/ supply order, the contract shall stand
cancelled & the performance security shall stand forfeited.
8. AIIMS Bhopal shall not be responsible for any financial loss or other damaged or injury to any item or person
deployed/supplied by the successful bidder in the course of their performing the duties to this office in connection
with purchase order/supply order for Supply of Indian Implants Equipment’s.
9. The Competent Authority of AIIMS Bhopal reserves the right to relax/withdraw any of the terms and conditions
mentioned in the tender documents, if doing so is in the interest of the AIIMS Bhopal.
10. The rate submitted by the Agency should not be higher than the Govt. Approved /DGS&D Rates at which the Supply of
Indian Implants Equipment’s are being supplied by it to other Govt. Institutes/Ministries/Departments. If subsequently
it is found that the firm has supplied equipment’s at higher rates to the AIIMS Bhopal, the excess amount shall be
recovered from the Performance Security and/or from the pending bills of the firm along with a penalty of Rs.1,000/-
on firm on such occasion and shall be doubled on subsequent occasions.
11. Delivery: Within 30 working days from the date of confirmed purchase Order/Purchase Instruction issued by the
Competent Authority of AIIMS Bhopal to AIIMS Bhopal at Saket Nagar, Bhopal-462 024 (MP).
12. Any complementary scheme offered by the manufacturer shall be provided to the AIIMS Bhopal with no additional cost.
13. The contract shall be for a period of one year from the date of award of contract or as indicated in the letter communicating award of contract to the selected firm(s). The contract may be extendable year to year, subject to maximum period of 1 year, on the same terms and conditions or with some addition/deletion/modification mutually agreed upon by the successful Supply of Indian Implants Equipment’s supplier Agency and the All India Institute of Medical Sciences (AIIMS) Bhopal.
14. The AIIMS Bhopal reserves the right to place an order for supply of any items mentioned in the Financial Bid (Chapter-7) or otherwise, to any other firm(s) in emergency/unavoidable situation i.e. auxiliary/ancillary/incidental to “Dictionary meaning” of Supply Of Indian Implants.
THIS AGREEMENT will take effect from _______________ day of _________________Two Thousand Thirteen and shall be
valid for one year.
IN WITNESS WHEREOF both the parties here to have caused their respective common seals to be hereunto affixed / (or have
hereunto set their respective hands and seals) the day and year mentioned above in Bhopal in the presence of the witness:
For and on behalf of the ‘Agency’
Signature of the authorized Official
Name of the Official
For and on behalf of the “Director, AIIMS Bhopal”
Signature of the authorized Officer
Name of the Officer
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 35 of 62
Stamp / Seal of the ‘Agency’
SIGNED, SEALED AND DELIVERED
By the Said
____________________________Name
on behalf of the ‘Agency’
in presence of
Witness:__________________________
Name :___________________________
Address:_________________________
_________________________________
By the said
_______________________________Name
on behalf of the “Director, AIIMS Bhopal”
in presence of
Witness:_____________________________
Name: ______________________________
Address:_____________________________
____________________________________
Tender No. 111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 36 of 62
Format of Performance Bank Guarantee (To be made on Rs 100.00 Non Judicial Stamp/E Stamp Paper) To,
The “Director”, All India Institute of Medical Sciences (AIIMS) Bhopal Saket Nagar, Bhopal- 462 024 (MP) INDIA
WHEREAS _______________________________________ (Name and address of the supplier) (Hereinafter called “the supplier”) has undertaken, in pursuance of contract no___________________________________________________________ dated _____________ to supply (description of goods and services) (herein after called “the Supplier”). AND WHEREAS it has been stipulated by you in the said contract that the supplier shall furnish you with a bank guarantee by a scheduled commercial bank recognised by you for the sum specified therein as security for compliance with its obligations in accordance with the contract; AND WHEREAS we have agreed to give the supplier such a bank guarantee; NOW THEREFORE we hereby affirm that we are guarantors and responsible to you, on behalf of the supplier, up to a total of. ________________________ (Amount of the guarantee in words and figures), and we undertake to pay you, upon your first written demand declaring the supplier to be in default under the contract and without cavil or argument, any sum or sums within the limits of (amount of guarantee) as aforesaid, without your needing to prove or to show grounds or reasons for your demand or the sum specified therein. We hereby waive the necessity of your demanding the said debt from the supplier before presenting us with the demand. We further agree that no change or addition to or other modification of the terms of the contract to be performed there under or of any of the contract documents which may be made between you and the supplier shall in any way release us from any liability under this guarantee and we hereby waive notice of any such change, addition or modification. This guarantee shall be valid up to 39 (Thirty Nine) months from the date of issue (indicate date) …………………… valid up to …………………………………..
……………………………..……………………………. (Signature with date of the authorised officer of the Bank)
…..…………………………………………………………. Name and designation of the officer
….…………………………………………………………. ….………………………………………………………….
Seal, name & address of the Bank and address of the Branch
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 37 of 62
Chapter – 7
Financial Bid Supply of Indian Implants for Orthopaedics Department at AIIMS Bhopal at AIIMS Bhopal, Saket Nagar, Bhopal-462 024. The price bid should be kept in separate sealed envelope
superscripting “Financial Bid for Tender No.111: AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated 22.11.2014
*AIIMS Bhopal authorities reserve the full rights to increase/decrease the quantity of items in the time of award of tender as per its actual requirement. The quantities mentioned
below in this tender against each item are only indicative/tentative nature.
1 2 3 4 5 6 7 8 9
S.No DESCRIPTION Qty Unit Basic Cost per Unit (in Rs.)
VAT and all other
applicable taxes
Fewer Discounts Offered (if Any)
per unit (in Rs.)
Total unit Cost including all taxes (FOR Destination)
(in Rs.)
Total Cost for Quantity given in Column 4
(including all taxes in Rs.)
Set 1 Stainless Steel Plates and Screws Set
1 Stainless Steel Plates (4.5mm) and Screws Set
1.1. Stainless Steel Plates (4.5mm) and Screws Set
1.1.1. Dynamic Compression Plates (Narrow) ‐ 6 holes ‐12 holes
10
1.1.2. Dynamic Compression Plates (Broad) ‐ 6 holes‐18 holes
10
1.1.3. Semi Tubular Plates ‐ 6 holes to 12 holes 5
1.1.4. Reconstruction Plates ‐6 holes to 12 holes 5
1.1.5. Cortical Screws (4.5 mm) ‐ 20 mm to 60 mm
100
1.1.6. Cancellous Screws (6.5mm, fully threaded) ‐ 25mm – 110mm
100
1.1.7. Cancellous Screws (6.5 mm, partially threaded) ‐ 25mm‐100mm
1.2. Stainless Steel Plates (3.5mm) and Screws Set
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 38 of 62
1.2.1. Dynamic Compression Plates ‐ 4 holes to 10 holes
10
1.2.2. Limited Contact-Dynamic Compression Plates (LC-DCP) ‐ 4 holes to 10 holes
10
1.2.3. 1/3 Tubular Plates ‐ 4 holes to 10 holes 5
1.2.4. Reconstruction Plate‐ 4 holes to 10 holes 5
1.2.5. Cortical Screws (3.5mm) – 8mm to 24mm 100
1.2.6. Cancellous Screws (4.0 mm, fully threaded) ‐ 10mm‐50 mm
100
1.2.7. Cancellous Screws (4.0 mm, partially threaded) ‐ 20mm‐50 mm
100
1.3. Peri-Articular Plates (4.5mm and 3.5mm) and Screws Set
1.3.1. T-Plates (4.5mm) – 4 holes to 12 holes 5
1.3.2. L-Plates (4.5mm)– 4 holes to 12 holes 5
1.3.3. L-Plates (3.5mm)– 3 holes to 6 holes 5
1.3.4. Buttress Plates (4.5mm) – 4 holes to 12 holes
5
1.3.5. Cortical screws – 20 mm– 60mm 100
1.3.6. Cancellous screws, (6.0mm/4.0mm), fully threaded – 25 mm– 110 mm
50
Grand Total For Set - 1
Set 2
2 Titanium Plates and Screws Set
2.1. Titanium Plates (4.5mm) and Screws Set
2.1.1. Dynamic Compression Plates (Narrow) ‐ 6 holes ‐12 holes
10
2.1.2. Dynamic Compression Plates (Broad) ‐ 6 holes‐18 holes
10
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 39 of 62
2.1.3. Semi Tubular Plates ‐ 6 holes to 12 holes 5
2.1.4. Reconstruction Plates ‐6 holes to 12 holes 5
2.1.5. Cortical Screws (4.5 mm) ‐ 20 mm to 60 mm
100
2.1.6. Cancellous Screws (6.5mm, fully threaded) ‐ 25mm – 110mm
50
2.1.7. Cancellous Screws (6.5 mm, partially threaded) ‐ 25mm‐100mm
50
2.2. Titanium Plates (3.5mm) and Screws Set
2.2.1. Dynamic Compression Plates ‐ 4 holes to 10 holes
10
2.2.2. Limited Contact-Dynamic Compression Plates (LC-DCP) ‐ 4 holes to 10 holes
5
2.2.3. 1/3 Tubular Plates ‐ 4 holes to 10 holes 5
2.2.4. Reconstruction Plate‐ 4 holes to 10 holes 5
2.2.5. Cortical Screws (3.5mm) – 8mm to 24mm 100
2.2.6. Cancellous Screws (4.0 mm, fully threaded) ‐ 10mm‐50 mm
50
2.2.7. Cancellous Screws (4.0 mm, partially threaded) ‐ 20mm‐50 mm
50
Grand Total For Set - 2
Set 3
3 Titanium Locking Compression Plates and Screws Set
3.1. Locking Compression Plates (4.5 mm)
3.1.1. Locking Compression Plates, Narrow, 6 holes ‐16 holes
10
3.1.2. Locking Compression Plates, Broad, 6 holes ‐ 18 holes
10
3.1.3. T‐Plate Locking Compression Plates, 3 holes to 8 holes
5
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 40 of 62
3.1.4. T‐Buttress Locking Compression Plates, 4 holes to 6 holes
5
3.1.5. L‐Buttress Locking Compression Plates, left / right, 3 holes to 6 holes
5
3.1.6. Locking Reconstruction Plates, 5 holes ‐ 16 holes
5
3.1.7. Cortical Screws, 4.5 mm, length ‐ 14 mm to 90 mm
100
3.1.8. Cancellous Screws, 6.5mm, 16mm threaded, length 30 mm – 120 mm
50
3.1.9. Cancellous Screws, 6.5 mm, 32mm threaded25mm‐110mm
50
3.1.10. Cancellous Screws, 6.5 mm, fully threaded 25mm‐110mm
50
3.1.11. Locking screws – 14 mm – 90 mm 50
3.2. Locking Compression Plates (3.5 mm)
3.2.1. Locking Compression Plates, 3.5 mm, 5 holes – 12 holes
10
3.2.2. Locking T. Plates 3.5mm, right/left/oblique, 6 holes ‐16 holes
5
3.2.3. Locking 1/3 Tubular Plates 3.5 mm, 4 holes to 10 holes
5
3.2.3. Locking Reconstruction Plates, 5 holes – 14 holes
5
3.2.5. Cortical Screws 3.5mm, 8mm to 24mm 100
3.2.6. Cancellous Screws 4.0 mm, fully threaded, 10 mm‐50 mm
50
3.2.7. Cancellous Screws 4.0 mm, partially threaded, 20 mm ‐50 mm
50
3.2.8. Locking screws, 18 mm ‐ 55 mm 50
Grand Total For Set - 3
Set 4
4 Stainless Steel Locking Compression Plates and Screws Set
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 41 of 62
4.1. Locking Compression Plates (4.5 mm)
4.1.1. Locking Compression Plates, Narrow, 6 holes ‐16 holes
10
4.1.2. Locking Compression Plates, Broad, 6 holes ‐ 18 holes
10
4.1.3. T‐Plate Locking Compression Plates, 3 holes to 8 holes
5
4.1.4. T‐Buttress Locking Compression Plates, 4 holes to 6 holes
5
4.1.5. L‐Buttress Locking Compression Plates, left / right, 3 holes to 6 holes
5
4.1.6. Locking Reconstruction Plates, 5 holes ‐ 16 holes
5
4.1.7. Cortical Screws, 4.5 mm, length ‐ 14 mm to 90 mm
100
4.1.8. Cancellous Screws, 6.5mm, 16mm threaded, length 30 mm – 120 mm
50
4.1.9. Cancellous Screws, 6.5 mm, 32mm threaded 25mm – 110mm
50
4.1.10. Cancellous Screws, 6.5 mm, fully threaded 25mm – 110mm
50
4.1.11. Locking screws – 14 mm – 90 mm 50
4.2 Locking Compression Plates (3.5 mm)
4.2.1. Locking Compression Plates, 3.5 mm, 5 holes – 12 holes
10
4.2.2. Locking T. Plates 3.5mm, right/left/oblique, 6 holes ‐16 holes
5
4.2.3. Locking 1/3 Tubular Plates 3.5 mm, 4 holes to 10 holes
5
4.2.4. Locking Reconstruction Plates, 5 holes – 14 holes
5
4.2.5. Cortical Screws 3.5mm, 8mm to 24mm 100
4.2.6 Cancellous Screws 4.0 mm, fully threaded, 10 mm‐50 mm
50
4.2.7. Cancellous Screws 4.0 mm, partially threaded, 20 mm ‐50 mm
50
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 42 of 62
4.2.8. Locking screws, 18 mm – 55 mm 50
Grand Total For Set - 4
Group -2 (Set-5,6,7,8)
Set 5
5 Interlocking Nails (Stainless Steel)
5.1. For Humerus
5.1.1. Humeral Nails, 6,7, 8mm,190‐310mm 5
Suture holes at proximal end
Two oblique holes proximally
Antero-posterior distal locking
5.1.2. Locking screws – assorted sizes 10
5.1.3. End cap – assorted size 5
5.1.4. Spiral blades – assorted sizes 5
Proximal drill guide should be radiolucent.
Should be supplied Sterile Packed
5.2. For Tibia
5.2.1. Unreamed Tibial Nail
5.2.1.1. Solid nails, bevelled proximal tip, D 8 – 9mm, Length 280‐380mm
5
With proximal transverse holes so that fractures close to the joint spacecan be treated by inserting oblique screws that should not compromisethe Tibial plateau posteriorly.
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 43 of 62
Proximal Dynamic slot to allow compression
Further distal hole to treat distal metaphyseal fractures
Should be supplied Sterile Packed
Proximal Drill guide should be radiolucent.
5.2.1.2. End caps, assorted sizes 5
5.2.1.3. Locking bolts, assorted sizes 10
5.2.2. Reamed Tibial Nail 10
5.2.2.1. Cannulated nail, 8 - 10mm, 300‐360mm
Bevelled proximal end, tapered distal tip
Two slots at both ends for locking
5.2.2.2. Locking bolts/end cap assorted sizes 10
5.3. For Femur
5.3.1. Antegrade Femoral Interlocking Nail 5
5.3.1.1. Femoral Nails ‐ 8mm to 14mm, Length 24 cm to 46cm
5.3.1.2. Hip Screws, 6.5mm, 60mm to 130mm 10
5.3.1.3. Low Profile Cortical Locking Bolts ‐ 4.2mm, 20mm to 90mm
10
Suitable for interlocking and reconstruction purposes
With facility for dynamization
Nail should be cannulated
Should be supplied Sterile Packed
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 44 of 62
Proximal Drill Guide should be radiolucent.
5.3.2. Retrograde Femoral Interlocking Nail
5.3.2.1. Femoral Nails, 9 ‐ 14mm, 160mm to 420mm
5
5.3.2.2. Spiral blades – 60 – 80 mm 5
5.3.2.3. Locking bolts and end cap – assorted sizes 5
With Dynamic slot
Three closely located distal holes for Supracondylar fracture
Five Degree Distal Bend to accommodate Inter-condylar notch
Should be supplied Sterile Packed
Drill guide should be radiolucent.
Grand Total For Set - 5
Set 6
6 Interlocking Nails (Titanium)
6.1. For Humerus
Humerus interlocking nail
Provisions for high proximal and low distal fracture fixations
6.1.1. Sizes: 6.7mm to 9.5mm, length 190mm to 310mm
5
6.1.2. Locking Screws 3.9mm 16mm to 60mm 5
6.1.3. Bolts/end cap 5
6.2. For Tibia
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 45 of 62
6.2.1. Unreamed Tibial Nail
Should have anatomical shape with anti-curvature and lateralization
Nail should be Solid/Cannulated
9 ‐ 11° bend in the proximal part
The runner shaped Tapered tip
Locking options proximally 2 medio-lateral and one dynamization slot,distally 2 medio-lateral , 2 anterio-posterior, the last slot should not bemore than 10mm away from distal tip.
6.2.1.1. Sizes : 8 ‐10mm, length 240 to 420mm 5
6.2.1.2. Endcaps 0 to 25mm 5
6.2.2. Reamed Tibial Nail
Should have anatomical shape with anti-curvature and lateralization.
The Nail should be cannulated.
9 ‐ 11° bend in the proximal part.
The runner shaped Tapered tip
Locking options proximally 2 medio-lateral and one dynamization slot,distally 2 medio-lateral , 2 anterio-posterior, the last slot should not bemore than 10mm away from distal tip.
6.2.2.1. Sizes : 8 ‐10mm, length 240 to 420mm 10
6.2.2.2. End-caps 0 to 25mm 5
6.2.3. Tibial Nail for metaphyseal and diaphyseal fractures
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 46 of 62
Anatomically contoured nail, cannulated nail
Multiple locking options at both ends of nail
Multi directional proximal slots with provision for standard/ cancellouslocking screws
6.2.3.1. Nail – 8mm‐10 mm, 280mm‐ 410mm 5
6.2.3.2. Locking screws – 4.0mm, 16mm‐64mm 5
6.2.3.3. Locking screws – 5.0mm, 24mm‐64mm 10
6.2.3.4. End cap – 0 to 18mm 5
6.3. For Femur
6.3.1. Antegrade Femoral Interlocking Nail
6.3.1.1. Femoral Nails ‐ 8mm to 14mm, length 240 to 460mm
5
6.3.1.2. Reconstruction Screws, 5.5mm, 60mm to 130mm
5
6.3.1.3. Low Profile Cortical Locking Bolts ‐ 4.2mm, 20mm to 90mm
5
Suitable for interlocking and
reconstruction purposes
With facility for dynamization
Nail should be cannulated
Should be supplied Sterile Packed
Proximal Drill Guide should be
radiolucent.
6.3.2. Retrograde Femoral Interlocking Nail
6.3.2.1. Femoral Nails, 10 ‐ 14mm, 160mm to 420mm
5
6.3.2.2. Locking bolts, end cap 5
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 47 of 62
With Dynamic slots
Three closely located distal holes for Supracondylar fracture
Five Degree Distal Bend to accommodate Inter-condylar notch
Should be supplied Sterile Packed
Drill guide should be radiolucent.
6.3.3. Proximal Femoral Interlocking Nail
Anatomically designed for femur
Two locking options for neck
Safety provision to prevent screw slippage into femoral neck
Option for de-rotational hip pin
Distal slot with options of static/dynamic locking
6.3.3.1. Nail ‐ 10‐ 11mm,200 – 420mm 5
6.3.3.2. Neck screw – 11mm, 80 – 110mm 5
6.3.3.3. Hip pin – 6.5mm, 75‐100mm 5
6.3.3.4. Locking bolts/end cap – assorted size 5
Grand Total For Set - 6
Set 7
7 Condylar Blade Plate, DHS & DCS set
7.1. 95° Condylar Blade Plate
7.1.1. Plate Sizes 5 to14 Holes 5
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 48 of 62
7.1.2. Blade Length 50 – 80mm
7.2. DHS & DCS set
DHS Plates ‐ 135deg – 150 deg 5
7.2.1. L 46 – 270mm, 2 to 16 holes 5
7.2.2. Barrel L 25 – 38mm
DCS Plates – 95 deg
7.2.3. L114 – 370mm, 6 – 22 holes 5
7.2.4. Barrel L 25mm
DHS/DCS Screws
7.2.5. L 65 – 110mm, Thread L 22mm 5
7.2.6. Compression Screw – 36mm 5
Grand Total For Set - 7
Set 8
8 Nails, and Wires -Stainless steel
8.1. Kirschner (K‐) Wires
8.1.1. 1.0mm diameter, with trocar tip, L 150mm 100
8.1.2. 1.2mm diameter, with trocar tip, L 150mm 100
8.1.3. 1.5mm diameter, with trocar tip, L 150mm 250
8.1.4. 2.0mm diameter, with trocar tip, L 150mm 100
8.2. Kuntscher - Nails
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 49 of 62
8.2.1. Assorted sizes 10
8.3. Steinmann Pins
8.3.1. 3.5mm – 4.5mm 50
Trocar tip; Assorted sizes
8.4. Wire Sutures
8.4.1. 18G to 22G 5
Grand Total For Set - 8
Set 9
9 Screws, Drill Bits, and Bone Taps
Screws – Should be provided with 2 screw-drivers for each type
9.1.1. 7.3 mm Cancellous Screw
9.1.1.1. Deep cancellous thread with reverse cutting flutes
9.1.1.2. Threaded 16 mm, 40 mm to 120 mm 50
9.1.1.3. Threaded 32 mm, 50 mm to 150 mm 50
9.1.2. 6.5 mm Cancellous Screw (Stainless Steel)
9.1.2.1. Threaded 16 mm, 30 mm to 120 mm 50
9.1.2.2. Threaded 32 mm, 45 mm to 150 mm 50
9.1.2.3. Fully threaded 20 mm to 110 mm
9.1.3. 6.5 mm Cancellous Screw (Titanium)
9.1.3.1. Threaded 16 mm, 30 mm to 120 mm 50
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 50 of 62
9.1.3.2. Threaded 32 mm, 45 mm to 150 mm 50
9.1.3.3. Fully threaded 20 mm to 110 mm 50
9.1.4. 4.5 mm Malleolar Screw
9.1.4.1. 4.5 mm Malleolar Screws (Stainless Steel) 10
9.1.4.2. Head & Core D 8 mm x 3 mm
9.1.4.3. L25 mm to 70 mm
9.1.4.4. Thread D 12 to 32 mm
9.1.5. Cortex Screw 3.5 mm
9.1.5.1. 3.5 mm Cortex Screws (Stainless Steel)
9.1.5.2. 10 mm to 40 mm 100
9.1.5.3. 3.5 mm Cortex Screw (Titanium)
9.1.5.4. 10 mm to 90 mm 50
9.2. Cannulated Screws – should be supplied with complete instrumentation
9.2.1. 4.0mm Cannulated screw set
9.2.1.1. 4.0mm cannulated 316L stainless steel 25
Partially threaded, L 14 -30 (2mm increment), 35-75 (5mm increment)
9.2.1.1.1. Fully threaded, L 14 -30 (2mm increment), 35-75 (5mm increment)
10
9.2.1.1.2. Washer 7mm 5
9.2.1.2. 4.0mm cannulated Titanium alloy
9.2.1.2.1. Partially threaded, L 14 -30 (2mm increment), 35-75 (5mm increment)
10
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 51 of 62
9.2.1.2.2. Fully threaded, L 14 -30 (2mm increment), 35-75 (5mm increment)
10
9.2.1.2.3. Washer 7mm 5
9.2.2. Cannulated headless compression screw set (Herbert-Whipple type)
Should be made up of Titanium alloy
9.2.2.1. 3.5mm Diameter Screw
Length (mm): 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30
10
9.2.2.2. 4.5mm Diameter Screw
Length (mm): 14, 16, 18, 20, 22, 24, 26, 28, 30 5
9.2.2.3. 6.5mm Diameter Screw
Length (mm): 14, 16, 18, 20, 22, 24, 26, 28, 30 5
9.3. Drill Bits
9.3.1. Drill bit 4.5 mm 2
D 4.5 mm x L 147 mm
Thread L 120 mm
9.3.2. Drill bit 4.5 mm 2
D 4.5 mm x L 130 mm
Thread L 115 mm
9.3.3. Drill bit 4.5 mm 2
D 4.5 mm x L 195 mm
Thread L 170 mm
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 52 of 62
9.3.4. Drill bit 4.5 mm 2
D 4.5 mm x L 180 mm
Thread L 165 mm
9.3.5. Drill bit 3.5 mm 2
D 3.5 mm x L 100 mm
Thread L 85 mm
9.3.6. Drill bit 3.5 mm 2
D 3.5 mm x L 195 mm
Thread L 170 mm
9.3.7. Drill bit 3.5 (Cannulated) 2
D 3.5/1.35 mm x L 160/130 mm
9.3.8. Drill bit 3.2 mm 2
D 3.2 mm x L 225 mm
Thread L 200 mm
9.3.9. Drill bit 3.2 mm 2
D 3.2 mm x L 180 mm
Thread L 165 mm
9.3.10. Drill bit 3.2 mm 2
D 3.2 mm x L 145 mm
Thread L 120 mm
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 53 of 62
9.3.11. Drill bit 3.2 mm 2
D 3.2 mm x L 130 mm
Thread L 115 mm
9.3.12. Drill bit 2.8 mm 2
D 2.8 mm x L 165 mm
9.3.13. Drill bit 2.7 mm 2
D 2.7 mm x L 100 m
Thread L 75 mm
9.3.14. Drill bit 2.7 mm 2
D 2.7 mm x L 85 mm
Thread L 70 mm
9.3.15. Drill bit 2.7 mm 2
D 2.7 mm x L 125 mm
Thread L 100 mm
9.3.16. Drill bit 2.7 (Cannulated) 2
D 2.7/1.35 mm x L 160/130 mm
9.3.17. Drill bit 2.5 mm 2
D 2.5 mm x L 95 mm
Thread L 70 mm
9.3.18. Drill bit 2.5 mm 2
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 54 of 62
D 2.5 mm x L 112 mm
Thread L 85 mm
9.3.19. Drill bit 2.0 mm 2
D 2.0 mm x L 102 mm
Thread L 75 mm
9.3.20. Drill bit 2.0 mm 2
D 2.0 mm x L 85 mm
Thread L 70 mm
9.3.21. Drill bit 2.0 mm 2
D 2.0 mm x L 125 mm
Thread L 100 mm
9.3.22. Drill bit 1.5 mm 2
D 1.5 mm x L 70 mm
Thread L 55 mm
9.3.23. Drill bit 1.5 mm 2
D 1.5 mm x L 85 mm
Thread L 60 mm
9.3.24. Drill bit 1.5 mm 2
D 1.5 mm x L 110 mm
Thread L 85 mm
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 55 of 62
9.3.25. Drill bit 1.1 mm 2
D 1.1 mm x L 45 mm
Thread L 30 mm
9.3.26. Drill bit 1.1 mm 2
D 1.1 mm x L 60 mm
Thread L 35 mm
9.4. Bone Taps
9.4.1. 2.7mm 4
9.4.2. 3.5mm 4
9.4.3. 4mm 4
9.4.4. 4.5mm 4
9.4.5. 5mm 2
Grand Total For Set - 9
Group -3 (Set-10,11,13,14)
Set 10
10 Implants for Hip Arthroplasty
10.1. Austin Moore Prosthesis for hip
10.1.1. Head size 39mm – 55mm 10
10.2. Bipolar hip prosthesis Non-Modular (mono-block)
10.2.1. Size 39 to 53 10
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 56 of 62
Cemented and cementless
10.3. Bipolar hip prosthesis Modular 5
Should consist of
10.3.1. Femoral stem
10.3.2. Acetabular head
10.3.3. Bipolar cup with liner
10.3.4. Bone cement low viscosity 2 packets (40grams each)
10.3.5. Cement restrictor 8mm‐ 14mm
Grand Total For Set - 10
Set 11
11 Arthroscopic Implants for Knee and Shoulder Joints
11.1. Trans Fixation Pin (Titanium)
3mm‐5mm x 45mm‐50mm 5
11.2. Trans Fixation (Stainless steel)
4mm‐5mm x 45mm‐50mm 5
11.3. Interference Screws (Titanium)
Cannulated
7mm‐11mm x 20mm‐35mm 5
11.4. Interference Screws (Stainless steel) 5
11.5. Interference Screws (Bio-absorbable) 5
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 57 of 62
Round head, Cannulated
7mm‐ 1.0mm x 20mm‐ 35mm
11.6. Ligament Staple (Titanium) 5
8mm ‐ 20mm x 11mm ‐ 20mm
11.7. Ligament Staple (Stainless steel) 5
8mm ‐ 20mm x 11mm ‐ 20mm
11.8. Endo Buttons (Titanium) 5
3mm‐4mm x 9mm‐18mm
11.9. Endo Buttons (Stainless steel) 5
3mm‐4mm x 9mm‐18mm
11.10. Suture Washers/Disc (Titanium) 5
For graft fixation, 12mm‐ 18mm x 12mm‐ 20mm
11.11. Suture Washers / Disc (Stainless steel) 5
For graft fixation, 12mm‐ 18mm x 12mm‐ 20mm
11.12. Suture post (Titanium) 5
Flat head, Low profile screw
7mm‐ 10mm x 20mm‐ 35mm
11.13. Suture Anchors (Titanium) 5
2.3mm to 6.8mm
11.14. Arthroscopic Electrodes 2
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 58 of 62
Compatible with bipolar cautery consoles
90°, L‐ Hook
Grand Total For Set - 11
Group -4 (Set-12)
Set 12
12 Custom made Implants for Tumour Surgery
Material: Cobalt-Chrome alloy
Cost of extenstion block/ segment should be mentioned separately for each category
12.1. Custom Made Prosthesis for Distal Femur 2
Assorted sizes
12.2. Custom Made Prosthesis for Proximal Tibia
2
Assorted sizes
12.3. Custom Made Prosthesis for Proximal Femur
2
Assorted sizes
12.4. Custom Made Prosthesis for Proximal Humerus
2
Assorted sizes
Grand Total For Set - 12
Set 13
13 Implants for Spinal Surgery
Implants compatible with Indian titanium Instrumentation
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 59 of 62
The Screw Design should be compatible with 5mm Rod.
It should have Innie / Outie and Single Lock option with torque device available.
It should be compatible with Moss-Miami Instrumentation.
It should have an option of Minimally Invasive Spine Surgery also.
13.1. The Screws should be available in assorted diameter like 4.5mm, 5mm, 6mm, 7mm
20
13.2. The Screws should be available in assorted length of 25, 30, 35, 40, 45 and 50mm
13.3. Axial Connector 4/5 and 5/5. 20
13.4. Transverse Connector 10
13.5. Tapered Rod 3/4/5mm, and 4/5mm
13.6. Titanium Rod 5 mm x 480 mm 10
13.7. Hooks- Laminar, pedicular, Offset
13.8. Pelvic/ Iliac screws and pelvic fixation devices
13.9. Long screws
13.10. Reduction screws 5
13.11. Vertical titanium Mesh Cages (all sizes) 2
13.11.1. Titanium Mesh 18, 22, 28mm (varied lengths)
13.11.2. Titanium Mesh Size 13 X 70mm
13.11.3. Titanium Mesh Size 16 X 60mm
13.11.4. Titanium Mesh Size 19x 90mm
13.11.5. Titanium Mesh Size 10 x 100mm
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 60 of 62
13.11.6. Titaniumlordotic mesh 13 x 130 curved
13.11.7. Mesh 22x28mm Oval 15mm Height
13.11.8. Mesh 22x28mm Oval 50mm Height
13.11.9. Mesh 22x28mm Oval 70mm Height
13.11.10. Mesh 22x28mm Oval 90mm Height
13.11.11. Mesh 26x35mm Oval 90mm Height
13.12. Carbon Cages – Banana shaped – all sizes
13.13. Expandable Titanium cages – assorted sizes 1
13.14. Staples should be made from original titanium in four prong design.
5
The staple should be universal designed to cross the screw of various diameter sizes i.e. 4.5mm, 5mm, 6mm, and 7mm.
13.15. The double-hole staple should be made in various types like small, medium, large and extra-large.
It should be double-hole 4 prong.
It should have single-hole 3 prong.
The original open implant should be made available for demonstration at the time oftechnical evaluation.
Grand Total For Set - 13
Set 14
14 External Fixation Set
14.1. Tubular External Fixator System (in different combination as required) Stainless Steel
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 61 of 62
14.1.1. Universal Clamp 10
14.1.2. Rods D 11mm, Length 6” to 16” 10
14.1.3. Rod to Rod Clamp 5
14.1.4. Schanz Pin 45 mm cortical 10
14.1.5. Schanz Pin 6.0 mm cancellous 10
14.1.6. Spanner 10/11 10
14.2. Ring Fixator (external) System (in different combination as required)
14.2.1. Stainless steel rings ½ rings – 80 mm to 240 mm
50
14.2.2. Carbon ½ rings 60 – 180 mm 20
14.2.3. Threaded Rod 4” to 14” 10
14.2.4. Italian Arch assorted – 1400, 1600, 1800, 2000
10
14.2.5. Single pin Fixator central slot, side slot 50
14.2.6. Nut – 6 mm 50
14.2.7. Oblique Support 5
14.2.8. Female Posts 2 hole, 3 hole, 4 hole 5
14.2.9. Male Posts 2 hole, 3 hole, 4 hole 5
14.2.10. Hinges Male 5
14.2.11. Hinges Female 5
14.2.12. Hinges 90o
5
14.2.13. Short Connection Plates 5‐12 holes 5
Tender No. 111 : AIIMS Bhopal/Stores/RC/Orthopaedics Indian Implants/2014-2015/01 Dated. 11.02.2015
Page 62 of 62
14.2.14. Twisted Plates 1‐4 holes 5
14.2.15. Threaded Sockets 5
14.2.16. Olive Wires – 1.8 mm, 1.5 mm 50
14.2.17. K-Wires Trocar tips 1.8 mm, 1.5 mm 100
14.2.18. K-Wires Bayonet tips 1.8mm, 1.5mm 100
14.2.19. Wire Fixation Bolts – cannulated for 1.8mm and 1.5mm
100
14.2.20. Wire Fixation Bolts – slotted for 1.8mm and 1.5mm
100
14.2.21. Connecting Bolts 15 mm, 20 mm, 25 mm 200
14.2.22. Washers 10
14.2.23. Dynamometric tensioner 1
14.2.24. Wire tensioner 2
Grand Total For Set - 14
The supplier has to quote for each complete set in each group for which they are bidding. The price of each item in their respective group should be quoted separately. Bidder
has to quote complete set of each item in the respective group for which they are bidding otherwise they will be treated as disqualified.L-1 will be determined for total
complete amount group wise.
Prices to be quoted in Indian Rupees only.
Seal and signature of bidder Dated - ................................
The Technical Bid & Financial Bid should be kept in two separate sealed envelope superscripting with “Technical Bid for Supply of Indian Implants for Orthopaedics
Department at AIIMS Bhopal’ and “Financial Bid for Supply of Indian Implants for Orthopaedics Department at AIIMS Bhopal’ otherwise the Tenderer bid will be
rejected.