Transcript of SUPPLEMENTARY PLANNING GUIDANCE - Amazon S3
Supplementary Planning Guidance - Shop Fronts and Related
AdvertisementsSHOPFRONTS AND RELATED SHOPFRONTS AND RELATED
ADVERTISEMENTS ADVERTISEMENTS
SUPPLEMENTARY PLANNING GUIDANCE
3. Relationship to Unitary Development Plan 4
4. Development of Shop Fronts 4
5. Shopfronts 6
6. Materials 8
7. Fascias 11
10. Canopies and Blinds 17
11. Security 18
Appendix 2 UDP First Review (First Deposit) policies 29
Appendix 3 Other useful information 34
Document updated and reprinted January 2002
2
1.0 INTRODUCTION
1.1 The appeal and attractiveness of shopping centres depends not
only on the range of goods and services on offer but also on the
quality and appearance of the shopping environment.
1.2 A well designed, safe and attractive centre is good for
business - for both shoppers and tourists alike, and is much more
likely to be commercially successful than one where the shopping
environment is poor.
1.3 The appearance and character of shopping streets is strongly
influenced by the design and quality of individual shopfronts and
the advertisements, signs, canopies and security screens which go
with them. People tend to concentrate their gaze at ground floor
level when they wander through streets, and so the town’s
shopfronts will have a bigger impact on them than any other part of
the building.
1.4 Shopfronts with their associated advertisements are by their
very nature designed to attract attention and will, therefore,
dominate a street. A carefully designed shopfront promotes a
confident image of the shop itself and can make a positive
contribution to the character and trading success of the street in
which it is located.
1.5 A shopfront which does not relate well to its architectural
surroundings and has incongruous advertising suggests shabbiness
and lack of care. This can be particularly damaging, especially on
buildings of heritage value.
2.0 PURPOSE OF THE GUIDE
2.1 The Guide aims to provide detailed advice on good design
practice for new and altered shop fronts and advertisements.
Although it is of particular relevance to conservation areas,
listed buildings, buildings of local interest and the historic town
centre of Stockport where the need to protect and enhance the
Borough’s heritage is most important, it seeks to encourage quality
and good design in all shopping areas of the Borough.
2.2 The Council will always encourage flair and imaginative design
and does not intend the Guide to be a series of rigid and
inflexible rules. As buildings vary considerably, the imposition of
strict rules is neither appropriate nor desirable. Although it
recommends adherence to the principles of classical design as these
relate to proportion, balance and harmony, it does not suggest that
all new shop fronts be a slavish re-interpretation of traditional
designs. It is important that architectural style is not stifled,
and good quality materials, attention to detail and a design which
generally respects the building as a whole, whether modern or
historic, will usually be acceptable.
3
2.3 The Council does consider, however, that there are certain
broad criteria which have to be met in order to achieve the basic
objectives of quality in the design process. These criteria are
expressed as policy in the Council’s UDP.
3.0 RELATIONSHIP TO UNITARY DEVELOPMENT PLAN
3.1 The guidance is intended to expand upon and supplement the
policies contained in the UDP. Part I of the development plan sets
out the broad objectives for planning policy. It includes the
following proposal:
US 8 DESIGN IN SHOPPING AREAS
NEW SHOPPING DEVELOPMENTS OR ALTERATIONS TO EXISTING SHOPS
INCLUDING SHOPFRONTS, ADVERTISEMENTS AND SHOPFRONT SECURITY
MEASURES SHOULD DISPLAY A HIGH STANDARD OF DESIGN, MATERIALS AND
CONTRUCTION. SUCH DEVELOPMENT IN CONSERVATION AREAS, ON LISTED
BUILDINGS AND ON BUILDINGS OF LOCAL INTEREST MUST RESPECT THE
ARCHITECTURE AND HISTORIC VALUE OF THESE AREAS AND BUILDINGS.
3.2 The guidance does not have the same status as the UDP in that
it is policies contained in the UDP which provide the basis for
deciding planning applications. The Government nevertheless advises
that Supplementary Planning Guidance can be helpful for those
preparing planning applications and may be a means of implementing
some of the detailed proposals contained in the UDP. SPG may be
taken into account as a material consideration in the planning
process. The guidance must be consistent with the UDP.
3.3 The weight accorded to SPG increases if it has been prepared in
consultation with the public and has been the subject of a Council
resolution.
3.4 This guidance was circulated for public consultation in
April/May 1994. It was amended where considered appropriate and the
revised document approved for publication by the Council in October
1994. The SPG was updated and reprinted in 2002.
3.5 The relevant policies from the adopted UDP (February 1998) are
inserted at the beginning of appropriate sections as policy
background to the guidance. The Adopted Plan policies together with
their supporting explanations are included in Appendix 1. Relevant
draft policy from the First Deposit plan of the UDP review is
included in Appendix 2 for information.
4.0 DEVELOPMENT OF SHOPFRONTS
4.1 Although the buying and selling of goods has been carried on in
shopping streets for hundreds of years, the shop as it is today
with its integral shopfront is a relatively recent development
which only emerged at the end of the 17th Century.
4
4.2 The traditional shopfront tends to adhere to the principles of
classical design, comprising a number of features designed to
achieve the basic requirements for display. Each has its own visual
and practical function, enclosing and framing the shop window and
entrance.
4.3 With characteristic styles spanning Regency, Victorian and
Edwardian and inter War eras, the traditional shopfront tended to
be small and have its own separate frontage. Individual trade
styles created interest and variety whilst at the same time
maintaining an attractive and satisfactory relationship with the
buildings in which they were located and a sense of harmony and
rhythm in the shopping street
4.4 The latter half of the 20th Century witnessed profound changes
in retailing practice and in shopfront and advertisement design.
Much of this has been detrimental not only to the architecture and
character of shopping areas but also to their trading
performance.
5
4.5 Many modern shopfronts ignore the principles of traditional
shopfront design and in so doing have harmed the appearance of
shopping streets. Standardised corporate house styles and
shopfronts are not always appropriate or in character with the
building in which they are located. Neither are vast expanses of
plate glass, excessively deep box fascias with over-large
lettering, crude joinery, the extensive use of aluminum, acrylic,
perspex sheeting and projecting box signs.
5.0 SHOPFRONTS
UDP POLICY CONTEXT
US 8.1 SHOPFRONTS
THE COUNCIL WILL ONLY GRANT PERMISSION FOR NEW OR REPLACEMENT SHOP
AND COMMERCIAL FRONTS WHERE:
(i) THE DESIGN AND MATERIALS TO BE USED ARE SYMPATHETIC TO THE
CHARACTER, SCALE, PROPORTIONS AND DETAILING OF THE WHOLE BUILDING
AND PROPERTIES ADJACENT. EXISTING FRONTS OR DETAILING OF TOWNSCAPE
VALUE SHOULD BE RETAINED OR REINSTATED.
(ii) THE DESIGN OF DEVELOPMENT WHICH INCORPORATES ADJOINING
INDIVIDUAL SHOP FRONTAGES ON THE SAME OR ADJOINING BUILDINGS
RESPECTS THE INDIVIDUAL IDENTITY OF EACH SHOP AND BUILDING.
IN CONSERVATION AREAS AND ON LISTED BUILDINGS AND BUILDINGS OF
LOCAL INTEREST, SHOPFRONTS OF ARCHITECTURAL AND TOWNSCAPE VALUE
WILL BE RETAINED AND ACCURATELY RESTORED.
6
General
5.1 The design and materials to be used in shop fronts should be
sympathetic to the character, scale, proportions and detailing of
the whole building and properties adjacent. Existing fronts or
architectural detailing of townscape value should normally be
retained or reinstated.
5.2 Most shops display a vertical emphasis and most shopping
streets display a vertical rhythm which can be easily destroyed
when two or more properties combine to form one large shop. The
design of development, therefore, which incorporates adjoining
individual shop frontages on the same or adjoining buildings,
should respect the individual identity of each shop and
building.
Traditional Shopfronts
5.3 In conservation areas, on listed buildings and buildings of
local interest, shopfronts of architectural and townscape value
should be retained and accurately restored. In the case of
restoration work or where a replica shopfront is proposed, it is
vital that period details are correctly and accurately reproduced
in appropriate materials.
7
Modern Shopfronts
5.4 Non-traditional shopfronts in conservation areas, listed
buildings or in buildings of local interest should be a creative
interpretation of traditional principles. Elsewhere where a
non-traditional approach is favoured, shop fronts should form part
of an integrated design of high quality.
6.0 MATERIALS
6.1 The overall aim in selecting materials for shopfronts should be
their appropriateness, quality and durability.
6.2 Most traditional shopfronts were constructed of matt finished
painted timber in a dark colour. Hard woods including, teak, oak,
black walnut and mahogany were frequently chosen for their
aesthetic and practical qualities. The use of cast iron, plain,
etched or coloured glass, glazed and mosaic tiling was also
common.
6.3 The Art Deco detailing of the inter-war era produced designs of
high quality, using materials such as mahogany, chrome, bronze or
marble with distinctive period lettering.
8
Timber
6.4 Despite a decline in the use of hardwoods and the widespread
discouragement of their use when derived from non-sustainable
sources, there is a wide variety of modern timbers available. These
include softwood which when properly treated and maintained,
remains both a versatile and durable material for use in shopfront
construction.
6.5 The type of timber used, its quality, durability and appearance
can have a considerable bearing on the visual appearance and
maintenance characteristics of the shopfront. It is, therefore,
important for specifiers to be aware of the characteristics and
workability of timbers at the initial specification stage.
6.6 One of the most important aspects of joinery specification is
the moisture content of timber with its resultant implications for
shrinkage and movement. The foremost authority in this country on
timbers is TRADA (Timber Research and Development Association).
Details of some of the technical information available from TRADA
are contained in Appendix 3 to this document.
Exterior Finishes for Timber
6.7 The application of external finishes such as paint, varnish or
wood stains will greatly extend the life of timber. Susceptible
timbers should also be given an adequate preservative treatment
prior to the application of the finish.
6.8 Although lead based paint was the finish most commonly used on
the traditional shopfront, its availability has declined markedly
due to concerns about toxicity. Exterior quality paints are now
available in a wide variety. They have properties which resist the
passage of liquid water whilst allowing it to “breathe” - to escape
more freely from the wood as vapour. This helps maintain the wood
at a low moisture content.
6.9 The key to satisfactory paint adhesion and durability lies in
ensuring adequate preservative treatment, using aluminium primers
and careful preparation of the timbers. It is also vital to
understand the different qualities of the timbers being used.
Plywood
6.10 A number of elements in the shop front, particularly
stallrisers, are frequently constructed of plywood. It is essential
to ensure that a suitable grade of plywood for exterior use is
specified and that it has received adequate preservation treatment
prior to priming and painting.
9
Other Materials and Finishes
6.11 Natural or reconstituted stone is also occasionally used in
shopfront construction. Cast iron is a common feature in
traditional shops. Care should be taken with the use of materials
such as polished granite which give an unprofiled flat surface. A
bland finish can often result.
6.12 Glossy reflective surfaces such as acrylic sheeting, perspex,
plastic and silver aluminum are normally out of place in
conservation areas, listed buildings and on buildings of local
interest. Plastic laminates and glossy ceramic or composite tiles
occasionally used on stall risers and pilasters are similarly
inappropriate and are not usually sufficiently durable for
shopfronts.
6.13 Careful consideration should be given to appropriate door
furniture. Traditional handles, hinges and letterboxes should be
repaired and restored where possible.
Colours
6.14 The sensitive use of colour offers considerable scope for
improving the street scene. It can be used to pick out and enhance
architectural features and to help the shopfront blend in with the
rest of the building and street scene.
6.15 Most traditional timber shopfronts were finished in matt
paint, usually in rich dark colours such as red, blue, green, black
and brown. Warm colours, as a rule, complement old buildings. Their
darkness leaves the window display to provide the highlight and the
window/fascia lettering or shop furniture to provide the contrast,
e.g. gold lettering or brass furniture against a black background.
A range of traditional colours is now available from commercial
manufacturers.
6.16 Natural varnished hardwood is not a common feature in the
traditional shopping street and its use will be discouraged by the
Council.
10
6.17 Whilst there is no standard formula for the use of colour it
should be remembered that pale, cold colours can give a recessed
appearance, whilst warm rich colours convey a feeling of
projection.
General
6.18 The level of detail and care required in the design of the
shopfront and in the selection of materials, their quality, texture
and colours, is critical to the overall quality of the shopfront.
In an area of traditional buildings in particular, the standard of
design excellence requires skill and sensitivity. It is always
advisable, therefore, to employ an architect or designer with a
real understanding of the building and of the surrounding area.
Planning and conservation officers will always be pleased to advise
on the use of traditional materials and techniques.
6.19 As the quality of the shopfront depends on the level of
detailing, it is important that any plans and drawings submitted
are of a sufficient scale to show precisely what is proposed. This
applies in particular to the architectural detailing associated
with traditional buildings. The usual scale of 1:50 is normally too
small for this purpose, and drawings at a scale of 1:10 or 1:5 may,
therefore, be required giving precise details and sections of the
fascia, cornice, pilasters, mullions, stallriser and any other
architectural features.
7.0 FASCIAS
APPLICATIONS FOR ADVERTISEMENT CONSENT WILL BE CONSIDERED AGAINST
THE FOLLOWING CRITERIA:
(i) ALL ADVERTISEMENTS, ILLUMINATION APPARATUS, HANGING SIGNS AND
CANOPIES SHOULD REFLECT THE CHARACTER AND SCALE OF BUILDINGS TO
WHICH THEY RELATE AND SHOULD NOT FORM AN UNDULY DOMINANT OR
INTRUSIVE ELEMENT IN THE STREET SCENE;
(ii) THE HEIGHT OF FASCIA BOARDS SHOULD RESPECT THE PROPORTIONS OF
THE BUILDING AND THE ORIGINAL FASCIA IN THE CASE OF TRADITIONAL
SHOPFRONT REPLACEMENT;
(iii) IN MOST CIRCUMSTANCES PROJECTING BOX SIGNS AND INTERNALLY LIT
BOX FASCIAS ARE NOT APPROPRIATE IN CONSERVATION AREAS AND CONSENT
WILL NOT BE GRANTED FOR THESE UNLESS THE CHARACTER OR APPEARANCE OF
THE CONSERVATION AREA WOULD BE PRESERVED OR ENHANCED.
11
12
7.1 The prime function of the fascia is to provide advertising
space. As the fascia is probably the most noticeable element of a
shopfront, it is essential that it relates well to the rest of the
building and adjoining frontages.
7.2 Excessively deep box fascias with over-large lettering are
clumsy and should be avoided. Where the opportunity arises, fascias
which have exceeded the space originally intended for them or which
have obscured architectural details such as pilasters, other shop
front ornamentations or the sills and openings of first floor
windows above, should be reinstated to their original form.
7.3 Fascias should not be deepened to conceal a false ceiling.
Other methods such as setting back and forming a splayed bulkhead
or in the detailing of the transom should be considered. Fascias
may be angled forward or fitted with a projecting cornice to throw
rainwater clear of the shopfront, thereby preventing rot.
7.4 Modern boxed fascias which project beyond the face of the
building are clumsy and not normally acceptable. Glossy reflective
surfaces such as acrylic sheeting, perspex and plastic are normally
out of place in conservation areas, on listed buildings and
buildings of local interest. Matt finished painted timber fascias
in dark green, brown, navy blue, dark red or black are most
commonly associated with traditional shopfronts.
13
Fascia Signs
7.5 The name of the trader, the nature of the trade and the street
number should be sufficient information for a fascia board. Any
more is likely to lead to visual clutter.
7.6 Any additional signage can be provided by decorative
handpainted lettering applied discreetly to the shop window. Care
should be taken to ensure that it does not detract from the shop
front nor block large sections of window.
7.7 Hand painted lettering applied to the fascia in a style and
colour which harmonises with the rest of the shop front is
appropriate for traditional shopfronts. As an alternative,
appropriately styled, individually fixed lettering in brass, other
cast metal or in cut-out painted timber is also normally
acceptable. The use of glossy, cut-out sheet lettering is out of
place on traditional shopfronts. The corporate house advertisements
and signs of the large national and multinational companies should
reflect the character of the building.
7.8 As lettering and signage can evoke a particular image and
provide great decorative interest, the services of a competent sign
maker and writer are strongly recommended.
14
7.9 The lighting of shopping streets requires a co-ordinated
approach. The highlighting of buildings and pedestrian spaces is
the key to a lively and safe night-time environment. Shop signs do
not really need special illumination if the level of street
lighting and light from shop windows is adequate for trade.
7.10 The lighting of fascias or signs will normally be discouraged
in conservation areas, on listed buildings and on buildings of
local interest. It will usually only be acceptable in cases where
it can be demonstrated that the premises rely significantly on
after-dark trade, e.g. a pub, restaurant or place of entertainment,
and where the street is poorly lit.
7.11 Internally lit box fascias, individually illuminated letters,
halo lit perspex letters, swan neck and projecting spotlights will
normally be out of place on buildings and in streets of traditional
character.
7.12 It will generally not be appropriate to illuminate projecting
or hanging signs externally unless they belong to pubs, restaurants
or late opening premises.
7.13 Where external illumination of a fascia or sign is considered
acceptable, it should normally be by external means, e.g. by the
use of the least number of hooded spotlights or a full length strip
light concealed by a compact hood. External lighting should
normally be fixed to the fascia and painted to match the fascia, or
made of brass.
15
8.0 PROJECTING AND HANGING SIGNS
8.1 Projecting box signs with or without illuminations are normally
inappropriate in conservation areas, on listed buildings and on
buildings of local interest. Carefully designed, slender box signs
may be appropriate on certain modern buildings.
8.2 Traditional, non-illuminated, hand painted hanging signs are
the most appropriate form of projecting sign in the traditional
shopping street and fit in with the image of conservation areas.
They can add greatly to the general interest within the street
scene.
8.3 Hanging signs should normally be either painted timber or
metal, and fixed to the building with an iron bracket. Where an
original bracket survives, it should be re used.
8.4 The style of the sign and bracket should be appropriate to the
style of the building and relate well in terms of size and scale.
Lettering on the sign should normally refer to the name of the shop
or product sold, and not carry advertisements for brand name
products sold in the shop.
8.5 Hanging signs should normally be attached at fascia level or in
a position where the bottom of the sign is at the same level as the
first floor window cills. Their design should not detract from the
“host’ building or adjacent shops and buildings. Furthermore, they
must not create a hazard for pedestrians and vehicles.
8.6 Hanging signs can normally be successfully illuminated by the
use of spot lights.
16
Mounted Signs
9.1 Where the fascia is too narrow to adequately identify the
business, it may be acceptable to attach a mounted signboard
between the fascia and bottom of the cill at first floor window
level. Any such sign should respect the proportions of the
building, be appropriately crafted, should not cover details of
architectural interest and be used only for traditional
signwriting. Their use should be restricted so as not to create a
cluttered appearance in the street scene.
Business Nameplates
9.2 Where office premises are located above street level or in
cases where a conventional shopfront display is not possible, it is
commonplace to have a business nameplate next to the street
entrance.
9.3 In conservation areas, on listed buildings and buildings of
local interest, such plates should be of modest proportions,
ideally in brass and should not be illuminated. No more than one
sign may be displayed for each person, partnership or
company.
Window Lettering/Display
9.4 Any window lettering or decorative sign applied to the inside
of a shop window or at first floor level in the case of an office,
should respect the style and proportions of the building and not
result in a cluttered or untidy appearance.
9.5 Shop windows should never be obscured by a proliferation of
either stickers, posters or goods which can detract from the window
display.
10.0 CANOPIES AND BLINDS
10.1 The main purpose of a blind is to protect goods from damage by
sunlight. There should normally be no need for them, therefore, in
north facing or narrow streets.
10.2 Where they are used, they should always be retractable so that
the fascia is not permanently obscured. The traditional shop blind
was made of canvas with the blind box incorporated into the fascia
cornice. Where existing traditional retractable horizontal blinds
exist, the Council will encourage their retention and
renovation.
10.3 “Dutch” or balloon canopies or any form of plastic canopy will
not normally be allowed, particularly in conservation areas or in
older buildings. They are usually erected as a means of increasing
advertising space and tend to introduce an over dominant element
which can obscure the fascia and which is out of character with the
street.
10.4 Blinds will not normally be permitted above ground floor
level.
17
10.5 Where a blind is acceptable, consideration should be given as
to how best the blind box can be integrated within the overall
design. Incorporation within the fascia cornice was the traditional
solution in most cases.
11.0 SECURITY
APPLICATIONS TO INSTALL SECURITY MEASURES WILL BE CONSIDERED
AGAINST THE FOLLOWING CRITERIA:
(i) CRIME REDUCING FEATURES INCLUDING SHOP FRONT SECURITY MEASURES
AND FEATURES DESIGNED TO PREVENT RAMRAIDING MUST BE AN INTEGRAL
PART OF THE DESIGN AND CONSTRUCTION OF ANY PROPOSAL FOR DEVELOPMENT
OR REDEVELOPMENT. SUCH MEASURES SHOULD NOT DETRACT FROM THE
CHARACTER OF THE BUILDING OR THE AMENITY OF THE AREA;
(ii) WHERE ACCEPTABLE IN PRINCIPLE, EXTERNAL SHUTTERS AND OTHER
SECURITY MEASURES SHOULD RESPECT THE ARCHITECTURAL DETAILING OF THE
BUILDING AND BE DISCREETLY HOUSED;
(iii) THE USE OF UNCOLOURED ROLLER METAL SHUTTERS WILL NOT BE
PERMITTED AND SHOULD BE OF THE SLOTTED OR PERFORATED TYPE;
(iv) IN CONSERVATION AREAS, ON LISTED BUILDINGS OR BUILDINGS OF
LOCAL INTEREST, ROLLER SHUTTERS WILL BE REQUIRED TO BE HOUSED
INTERNALLY AND COLOUR COATED TO MATCH THE COLOUR SCHEME OF THE
PREMISES UNLESS ARCHITECTURAL DESIGN CONSIDERATIONS NECESSITATE A
DIFFERENT APPROACH.
11.1 The sharp rise in crime against property has had a profound
effect on commerce and retailing. It is the cause of dramatically
increasing insurance costs and creates losses in revenue through
loss of stock, damage to property, the disruption to trading and
the cost of providing security measures. Repeated attacks are
commonplace and can be financially crippling, particularly to the
small business.
11.2 The Council is sympathetic to the security needs of property
owners and recognises that unattended shops can be very vulnerable,
particularly those specialising in high value goods which can be
easily removed.
11.3 The emphasis given to security will depend upon a number of
factors. A shopping
18
area which is well laid out and well lit, lively in the evenings
and at weekends because of a resident community and/or businesses
operating outside normal trading hours (an “evening economy”), is
less attractive to the criminal than one which is poorly lit and
deserted.
11.4 Whilst the Council encourages traders to incorporate security
measures into the design of shops and shop fronts, it must ensure
that they do not detract from the appearance of the individual
building or the townscape. The Council considers it important that
security proposals are the subject of discussion between all
interested parties, including insurance companies, in order that
the details of individual cases may be made fully known.
Crime against shops - vandalism, theft and ramraiding
11.5 The escalation of vandalism, theft and ramraiding has resulted
in significant developments in the shop front security business. A
wide range of products is now available which greatly enhance shop
front security without detracting from its appearance.
11.6 With the range of security products currently available, it
should be possible to provide a shutter which will suit most
environments. In terms of products and materials, the use of
laminated glass and internally housed lattice grilles is now widely
recommended. In order to act as a deterrent, shopkeepers may wish
to consider advertising the use of laminated glass on their shop
fronts. A design which ensures that glazed areas are reduced and
vertical elements reinforced with steel or brick will greatly
reduce the opportunity for crime. The introduction or replacement
of a stallriser, reinforced with steel provides an effective
deterrent against ramraiding. So also do steel triangles and posts,
installed in the floor behind the shop window and raised at night
when the shop is empty. Open mesh shutters, strong enough to
withstand the impact of an ordinary vehicle, yet attractive to look
at and allowing for the display of goods to night-time passers-by
are another effective device designed to reduce the opportunity for
crime.
11.7 For any security device to be effective it is crucial that the
fitting is securely fixed to a stable part of the building, as
weakness in either can be exploited by the criminal. A housing
mechanism which stands proud of the shop front is more likely to be
levered out than one which is flush or located internally.
11.8 The Council recommends that developers and individual shop
owners incorporate crime reducing features into any proposals for
development or redevelopment.
11.9 The Council is also aware that the external environment of the
shop - its location, and the proximity and positioning of items of
street furniture such as bollards, litter bins, seating and
lamp-posts all have a potential bearing on the security of a
shop.
11.10 Whilst it is not the policy of the Council to pursue the
protection of individual properties against ramraiding, it has been
agreed that where a highway is subject to
19
redesign or improvement, any preventative measures to reduce the
incidence of ramraiding should be incorporated where
appropriate.
Steel Roller Shutters
11.11 Solid steel grey roller shutters, at one time considered the
ultimate in shop front security, have a particularly harmful effect
on visual amenity. They create a besieged appearance. When
multiplied across several shopfronts they create a threatening and
hostile environment. This reduces the attractiveness and viability
of a shopping area and can generate a negative image of the town.
The use of solid, uncoloured roller metal shutters will, therefore,
not normally be permitted.
11.12 Where roller shutters are permitted, they should be
self-coloured in appropriate factory-applied colour, of the slotted
or perforated type, should not cover the fascia, pilasters, stall
riser or other features and should be discreetly housed behind the
existing fascia line or integrated into the shop front.
The following illustrations are examples of different types of
security measures. Encouragement will be given to those measures
which have least impact on visual amenity.
20
21
Police Architectural Liaison Service
11.13 It is strongly recommended that traders concerned about any
aspect of shop security contact the Architectural Liaison Unit,
Community Affairs Branch, Greater Manchester Police, Chester House,
Boyer Street, Manchester M16 0RE (Tel: 0161 856 2255). The Police
provide advice and information on all aspects concerning the
security of commercial premises from the design of the external
environment and shop units themselves to the use of shop front
security measures, alarm systems and closed circuit
television.
12.0 ACCESS FOR THE DISABLED
12.1 Planning legislation requires local authorities to draw the
attention of developers to the needs of the disabled and those with
mobility difficulties. Developers are referred to the relevant
Planning and Building Control legislation and circulars, and other
professional and Government advice.
12.2 Steps should be avoided in favour of ramps. Where possible a
ramp and steps should be provided. Doors should be 850 mm wide to
allow for wheelchair access. A handrail is needed for support and
bells and handles should be within easy reach.
12.13 The Building Control Section of the Environment and Economic
Development Division should be contacted for further advice on this
matter.
13.0 IS PLANNING CONSENT REQUIRED?
Shopfronts
13.1 Planning consent is required for the change of use between
certain types of shop, and between shops and other uses.
13.2 Alterations to shopfronts will normally require consent under
the Planning Acts or Advertisement Regulations or both.
13.3 Planning consent is needed for any material change in the
external appearance of a shop. This could include altering the
glazing, changing the door, changing the facing materials,
installing blinds or shutters or enlarging the size of the
fascia.
Advertisements
13.4 Advertisement consent is required for the display of most
signs although there are some exceptions. As the Advertisement
Regulations are complex, advice should always be sought from the
Development Control Section. All illuminated signs require consent
in Conservation Areas.
22
Conservation Area Consent
13.5 With certain specific exceptions demolition or partial
demolition of any building in a conservation area needs
Conservation Area Consent.
Listed Building Consent
13.6 Any alterations affecting the character of a Listed Building
require consent. This can include such details as repainting in a
different colour, installing a security alarm or extractor fan,
altering the interior or installing blinds, shutters and
advertisements.
IT IS STRONGLY RECOMMENDED THAT ANY SHOP OWNER OR TENANT PROPOSING
TO PUT UP A SIGN OR TO ALTER A SHOP FRONT SHOULD GET IN TOUCH WITH
THE DEVELOPMENT CONTROL SECTION FIRST.
WORKS CARRIED OUT WITHOUT CONSENT MAY RESULT IN ENFORCEMENT ACTION
WHICH CAN CAUSE CONSIDERABLE DISRUPTION AND EXPENSE.
23
US8 DESIGN IN SHOPPING AREAS
NEW SHOPPING DEVELOPMENTS OR ALTERATIONS TO EXISTING SHOPS
INCLUDING SHOPFRONTS, ADVERTISEMENTS AND SHOP FRONT SECURITY
MEASURES SHOULD DISPLAY A HIGH STANDARD OF DESIGN, MATERIALS AND
CONSTRUCTION. SUCH DEVELOPMENT IN CONSERVATION AREAS, ON LISTED
BUILDINGS AND ON BUILDINGS OF LOCAL INTEREST MUST RESPECT THE
ARCHITECTURE AND HISTORIC VALUE OF THESE AREAS AND BUILDINGS.
Explanation The appeal and attractiveness of shops and shopping
centres depends not only on the range of goods and services on
offer, but also on the quality and appearance of the shopping
environment. A well-designed, safe and attractive shopping area is
good for business - for both shoppers and tourists alike, and is
much more likely to be commercially successful than one where the
shopping environment is poor.
The Council is also concerned that the appearance and character of
buildings which contribute to the Borough’s heritage should be
protected from unsympathetic development. In this respect,
development proposals will be required to satisfy the terms of
policies UN5 and UN6.
Proposals for development will also be required to satisfy the
provisions of Policy US1.2 which requires shopping development to
be accessible to all sections of the community. Developers and
others considering altering shop premises are referred to the
Council’s Supplementary Planning Guidance Note on “Shopfronts and
Related Advertisements”, which aims to provide detailed advice on
good design practice for new and altered shop fronts and
advertisements.
US8.1 SHOPFRONTS
THE COUNCIL WILL ONLY GRANT PERMISSION FOR NEW OR REPLACEMENT SHOP
AND COMMERCIAL FRONTS WHERE:
i) THE DESIGN AND MATERIALS TO BE USED ARE SYMPATHETIC TO THE
CHARACTER, SCALE, PROPORTIONS AND DETAILING OF THE WHOLE BUILDING
AND PROPERTIES ADJACENT. EXISTING FRONTS OR DETAILING OF TOWNSCAPE
VALUE SHOULD BE RETAINED OR REINSTATED;
ii) THE DESIGN OF DEVELOPMENT WHICH INCORPORATES
24
ADJOINING INDIVIDUAL SHOP FRONTAGES ON THE SAME OR ADJOINING
BUILDINGS RESPECTS THE INDIVIDUAL IDENTITY OF EACH SHOP AND
BUILDING.
IN CONSERVATION AREAS AND ON LISTED BUILDINGS AND BUILDINGS OF
LOCAL INTEREST, SHOPFRONTS OF ARCHITECTURAL AND TOWNSCAPE VALUE
WILL BE RETAINED AND ACCURATELY RESTORED.
Explanation Shopfronts with their associated advertisements are by
their very nature designed to attract attention and will therefore
dominate a street. A carefully designed shopfront promotes a
confident image of the shop itself and can make a positive
contribution to the character and trading success of the street in
which it is located. A shopfront which does not relate well to its
architectural surroundings and has incongruous advertising suggests
shabbiness and lack of care. This can be particularly damaging,
especially on buildings of heritage value.
The traditional shopfront comprises a number of features, each with
its own visual and practical function. These are designed to
achieve the basic requirement for display whilst remaining in
harmony with the building and the street scene.
There are a number of modern shopfronts in the Borough the design
of which has ignored the principles of traditional shopfront design
and in so doing has harmed the appearance of shopping streets.
Standardised corporate house styles and shop fronts are not always
appropriate or in character with the building in which they are
located. This applies particularly to conservation areas, listed
buildings and buildings of local interest.
Non-traditional shopfronts in conservation areas, listed buildings
or in buildings of local interest should be a creative
interpretation of traditional principles. Elsewhere where a
non-traditional approach is favoured, shop fronts should form part
of an integrated design of high quality. In all cases a shopfront
should respect the form, scale, materials, proportions and colour
of the building and neighbouring buildings.
In cases where a proposed shopfront will span more than one shop
and/or building, the Council is concerned that a standardised
shopfront and fascia should not destroy the individual identity of
the original shop and building, and the predominantly vertical
emphasis which most shopfronts display.
The Council favours the retention of shopfronts which are good
examples of a particular period and are of architectural and
townscape value. Where restoration works or where a replica
shopfront is proposed, it is vital that period details are
correctly and accurately reproduced in appropriate materials,
finishes and colours.
US8.2 ADVERTISEMENTS ON SHOPS
APPLICATIONS FOR ADVERTISEMENT CONSENT WILL BE CONSIDERED AGAINST
THE FOLLOWING CRITERIA:
25
i) ALL ADVERTISEMENTS, ILLUMINATION APPARATUS, HANGING SIGNS AND
CANOPIES SHOULD REFLECT THE CHARACTER AND SCALE OF BUILDINGS TO
WHICH THEY RELATE AND SHOULD NOT FORM AN UNDULY DOMINANT OR
INTRUSIVE ELEMENT IN THE STREET SCENE;
ii) THE HEIGHT OF FASCIA BOARDS SHOULD RESPECT THE PROPORTIONS OF
THE BUILDING AND THE ORIGINAL FASCIA IN THE CASE OF TRADITIONAL
SHOPFRONT REPLACEMENT;
iii) IN MOST CIRCUMSTANCES PROJECTING BOX SIGNS AND INTERNALLY LIT
BOX FASCIAS ARE NOT APPROPRIATE IN CONSERVATION AREAS AND CONSENT
WILL NOT BE GRANTED FOR THESE UNLESS THE CHARACTER OR APPEARANCE OF
THE CONSERVATION AREA WOULD BE PRESERVED OR ENHANCED.
Explanation Advertisements, well designed and appropriately located
are essential to the lively character and busy atmosphere which all
shopping areas seek to achieve. On the other hand, a proliferation
of poorly designed signs in inappropriate materials and locations
present an untidy and cluttered appearance and can detract from the
appearance of the building and the street scene. Applicants can
assist in this aim of avoiding clutter by restricting their
advertisements to those appropriate to the purpose of the building
e.g. to identify the business or trade conducted on the premises.
Control can be exercised by the Council if amenity or public safety
is affected.
The prime function of the fascia is to provide advertising space.
As the fascia is possibly the most noticeable element of a
shopfront, it is essential that it relates well to the rest of the
building and adjoining frontages. Excessively deep box fascias with
over-large lettering are clumsy and should be avoided.
In most circumstances it is only appropriate to site signs at
ground floor level; proposals for signs at or above first floor
level will be deemed to be unsatisfactory in relation to criterion
(i) if they would be unduly dominant or intrusive by reason of
their position or would have an adverse effect on the appearance of
the building.
Projecting box signs with or without illumination are normally
inappropriate in conservation areas, on listed buildings and on
buildings of local interest. Where illumination of a fascia or sign
is considered acceptable, it should normally be by external means,
e.g., by the use of the minimum number necessary of hooded
spotlights or a full length strip light concealed by a compact
hood.
Carefully designed, slender box signs may be appropriate on certain
modern buildings. Where illumination of signs or fascias is
permitted, it should be discreet, being an integral part of the
overall design and not merely a means of drawing attention to the
advertisement. The source of illumination should not be seen from a
highway in the interests of highway safety.
26
APPLICATIONS TO INSTALL SECURITY MEASURES WILL BE CONSIDERED
AGAINST THE FOLLOWING CRITERIA:
i) CRIME REDUCING FEATURES INCLUDING SHOP FRONT SECURITY MEASURES
AND FEATURES DESIGNED TO PREVENT RAMRAIDING MUST BE AN INTEGRAL
PART OF THE DESIGN AND CONSTRUCTION OF ANY PROPOSALS FOR
DEVELOPMENT OR REDEVELOPMENT. SUCH MEASURES SHOULD NOT DETRACT FROM
THE CHARACTER OF THE BUILDING OR THE AMENITY OF THE AREA;
ii) WHERE ACCEPTABLE IN PRINCIPLE, EXTERNAL SHUTTERS AND OTHER
SECURITY MEASURES SHOULD RESPECT THE ARCHITECTURAL DETAILING OF THE
BUILDING AND BE DISCREETLY HOUSED;
iii) THE USE OF UNCOLOURED METAL ROLLER SHUTTERS WILL NOT BE
PERMITTED AND SHOULD BE OF THE SLOTTED OR PERFORATED TYPE;
iv) IN CONSERVATION AREAS, ON LISTED BUILDINGS, OR BUILDINGS OF
LOCAL INTEREST, ROLLER SHUTTERS WILL BE REQUIRED TO BE HOUSED
INTERNALLY AND COLOUR COATED TO MATCH THE COLOUR SCHEME OF THE
PREMISES UNLESS ARCHITECTURAL DESIGN CONSIDERATIONS NECESSITATE A
DIFFERENT APPROACH.
Explanation The Council is sympathetic to the security needs of
property owners and recognises that shops can be especially
vulnerable. It must ensure however that security measures do not
detract from the individual building or from the townscape. Solid
security shutters have a particularly harmful effect on visual
amenity. They create a besieged appearance which when multiplied
across several shopfronts creates a threatening and hostile
environment. This can reduce the attractiveness and viability of a
shopping area and especially its evening economy, and can generate
a negative image of the town. Wherever possible the use of
alternative security measures should be considered, especially in
conservation areas and on listed buildings. Alternative measures
may include the use of laminated glass and internal lattice
grilles. Where roller shutters are permitted they should be
self-coloured in appropriate factory-applied colour, of the slotted
or perforated type and should not cover the fascia, pilasters,
stall riser or other features. All forms of shutter should be
discreetly housed behind the existing fascia line or integrated
into the shopfront.
Highway authorities do not have specific powers to erect bollards,
nor is this always an appropriate or desirable solution to the
problem of ramraiding, particularly in individual cases. The
majority of modern retail units have full height windows designed
to maximise display but which make them very vulnerable. The
traditional shopfront with its reduced
27
area of glass and reinforced stall riser is more resistant to
attack. The installation of external or internal shutters or
grilles and the use of laminated glass will also afford added
protection. Where a highway is subject to redesign or improvement,
any preventative measures to reduce the incidence of ramraiding can
be incorporated where appropriate.
28
UDP FIRST REVIEW POLICY (FIRST DEPOSIT)
The Stockport UDP is being reviewed. Below are the relevant
policies contained in the “First Deposit” draft of the revised
plan.
SE1 SHOPPING AND THE BUILT ENVIRONMENT
THE COUNCIL WILL REQUIRE THAT SHOPPING DEVELOPMENTS DO NOT
MATERIALLY HARM RESIDENTIAL AMENITY BY REASON OF NOISE, LOSS OF
PRIVACY, VISUAL APPEARANCE AND ADVERTISEMENT ILLUMINATION, OR
TRAFFIC GENERATION.
NEW SHOPPING DEVELOPMENTS OR ALTERATIONS TO EXISTING SHOPS
INCLUDING SHOPFRONTS, ADVERTISEMENTS AND SHOP FRONT SECURITY
MEASURES SHOULD DISPLAY A HIGH STANDARD OF DESIGN, MATERIALS AND
CONSTRUCTION. SUCH DEVELOPMENT IN CONSERVATION AREAS, ON LISTED
BUILDINGS AND ON BUILDINGS OF LOCAL INTEREST MUST RESPECT THE
ARCHITECTURE AND HISTORIC VALUE OF THESE AREAS AND BUILDINGS.
Explanation: The historic pattern and distribution of shops
includes many examples where environment and amenity have been
given little weight or consideration. Individual shops can be found
in the middle of residential terraces where the detrimental effect
on amenity can be magnified by the use of such premises as hot food
take-aways.
The scope for injury to amenity has grown in recent years
through:
• increased car usage leading to parking and traffic safety
problems • increased numbers of restaurants and hot food shops with
problems of smell, noise and
litter • extended hours of operation • modern intrusive illuminated
advertising.
The Council will prevent damage to residential amenities by
preventing the inappropriate location of retail development and by
the use of relevant conditions in granting planning
permission.
The appeal and attractiveness of shops and shopping centres depends
not only on the range of goods and services on offer, but also on
the quality and appearance of the shopping environment. A well
designed, safe and attractive shopping area is good for both
shoppers and tourists alike, and is much more likely to be
commercially successful than one where the shopping environment is
poor. Proposals should satisfy the requirements of Policy DCD1.1,
“Urban Design Principles” and Policy DCD1.3, “Access for People
with Access Difficulties”.
The Council is also concerned that the appearance and character of
buildings that
29
contribute to the Borough’s heritage should be protected from
unsympathetic development. Development proposals will be required
to satisfy the terms of policies HC1 and HC2.
Proposals for new or refurbished shopping development should
demonstrate that adequate facilities for dealing with trade waste
associated with the operation can be provided, including
appropriate recycling facilities, in accordance with Policy
MW1.5.
SE1.2 SHOPFRONTS
Permission for new or replacement shop and commercial fronts will
be permitted provided that:
(i) the design and materials to be used are sympathetic to the
character, scale, proportions and detailing of the whole building
and properties
adjacent. Existing fronts or detailing of townscape value should be
retained or reinstated;
(ii) the design of development which incorporates adjoining
individual shop frontages on the same or adjoining buildings
respects the individual identity of each shop and building.
In Conservation Areas and on Listed Buildings and buildings of
local interest, shopfronts of architectural and townscape value
should be retained and accurately restored.
Explanation: The appearance and character of shopping streets is
strongly influenced by the design and quality of individual
shopfronts and the advertisements, signs, canopies and security
screens which go with them. As people tend to concentrate their
gaze at ground floor level when they wander through streets
shopfronts will have a bigger impact on them than any other part of
the building. Shopfronts with their associated advertisements are
by their very nature designed to attract attention and will
therefore dominate a street. A carefully designed shopfront
promotes a confident image of the shop itself and can make a
positive contribution to the character and trading success of the
street in which it is located. A shopfront which does not relate
well to its architectural surroundings and has incongruous
advertising suggests shabbiness and lack of care. This can be
particularly damaging, especially on buildings of heritage
value.
The traditional shopfront comprises a number of features, each with
its own visual and practical function. These are designed to
achieve the basic requirement for display whilst remaining in
harmony with the building and the street scene. There are a number
of modern shopfronts in the Borough the design of which has ignored
the principles of traditional shopfront design and in so doing has
harmed the appearance of shopping streets. Standardised corporate
house styles and shop fronts are not always appropriate or in
character with the building in which they are located. This applies
particularly to Conservation Areas, Listed Buildings and buildings
of local interest.
30
Non-traditional shopfronts in Conservation Areas, Listed Buildings
or in buildings of local interest should be a creative
interpretation of traditional principles. Elsewhere where a
non-traditional approach is favoured, shop fronts should form part
of an integrated design of high quality. In all cases a shopfront
should respect the form, scale, materials, proportions and colour
of the building and neighbouring buildings.
In cases where a proposed shopfront will span more than one shop
and/or building, the Council is concerned that a standardised
shopfront and fascia should not destroy the individual identity of
the original shop and building, and the predominantly vertical
emphasis which most shopfronts display.
The Council favours the retention of shopfronts that are good
examples of a particular period and are of architectural and
townscape value. Where restoration works or where a replica
shopfront is proposed, it is vital that period details are
correctly and accurately reproduced in appropriate materials,
finishes and colours.
Reference should also be made to Supplementary Planning Guidance
“Shopfronts and Related Advertisements”.
SE1.3 ADVERTISEMENTS ON SHOPS
Applications for advertisement consent will be considered against
the following criteria:
(i) all advertisements, illumination apparatus, hanging signs and
canopies should reflect the character and scale of buildings to
which they relate, respect existing architectural features, and
should not form an unduly dominant or intrusive element in the
street scene;
(ii) the height of fascia boards should respect the proportions of
the building and the original fascia in the case of traditional
shopfront replacement;
(iii) in most circumstances projecting box signs and internally lit
box fascias are not appropriate in Conservation Areas and consent
will not be granted for these unless the character or appearance of
the conservation area would be preserved or enhanced.
Explanation: This policy is applicable where proposals are
acceptable in principle under Policy DCD1.7. Well designed and
appropriately located advertisements are essential to the lively
character and busy atmosphere which all shopping areas seek to
achieve. On the other hand, a proliferation of poorly designed
signs in inappropriate materials and locations present an untidy
and cluttered appearance and can detract from the appearance of the
building and the street scene. Applicants can assist in this aim of
avoiding clutter by restricting their advertisements to those
appropriate to the purpose of the building e.g. to identify the
business or trade conducted on the premises. The Council can
exercise control if amenity or public safety is affected.
31
On new buildings, signs should be considered as an integral part of
the design process, not added as an afterthought.
The prime function of the fascia is to provide advertising space.
As the fascia is possibly the most noticeable element of a
shopfront, it is essential that it relates well to the rest of the
building and adjoining frontages. Excessively deep box fascias with
over-large lettering are clumsy and should be avoided.
In most circumstances it is only appropriate to site signs at
ground floor level. Proposals for signs at or above first floor
level will be deemed to be unsatisfactory in relation to criterion
(i) if they would be unduly dominant or intrusive by reason of
their position or would have an adverse effect on the appearance of
the building.
Projecting box signs with or without illumination are normally
inappropriate in Conservation Areas, on Listed Buildings and on
buildings of local interest. Where illumination of a fascia or sign
is considered acceptable, it should normally be by external means,
e.g., by the use of the minimum number necessary of hooded
spotlights or a full length strip light concealed by a compact
hood.
Carefully designed, slender box signs may be appropriate on certain
modern buildings. Where illumination of signs or fascias is
permitted, it should be discreet, being an integral part of the
overall design and not merely a means of drawing attention to the
advertisement. The source of illumination should not be seen from a
highway in the interests of highway safety.
SE1.4 SECURITY MEASURES FOR SHOP FRONTS
Applications to install security measures will be considered
against the following criteria:
(i) crime reducing features including shop front security measures
and features designed to prevent ramraiding must be an integral
part of the design and construction of any proposals for
development or redevelopment. Such measures should not detract from
the character of the building or the amenity of the area;
(ii) where acceptable in principle, external shutters and other
security measures should respect the architectural detailing of the
building and be discreetly housed;
(iii) the use of uncoloured metal roller shutters will not be
permitted and should be of the slotted or perforated type;
(iv) in Conservation Areas, on Listed Buildings, or buildings of
local interest, roller shutters will be required to be housed
internally and colour coated to match the colour scheme of the
premises unless architectural design considerations necessitate a
different approach.
32
Explanation: The Council is sympathetic to the security needs of
property owners and recognises that shops can be especially
vulnerable. It must ensure however that security measures do not
detract from the individual building or from the townscape. Solid
security shutters have a particularly harmful effect on visual
amenity. They create a besieged appearance which when multiplied
across several shopfronts creates a threatening and hostile
environment. This can reduce the attractiveness and viability of a
shopping area and especially its evening economy, and can generate
a negative image of the town. Wherever possible the use of
alternative security measures should be considered, especially in
Conservation Areas and on Listed Buildings. Alternative measures
may include the use of laminated glass and internal lattice
grilles. Where roller shutters are permitted they should be
self-coloured in appropriate factory-applied colour, of the slotted
or perforated type and should not cover the fascia, pilasters,
stall riser or other features. All forms of shutter should be
discreetly housed behind the existing fascia line or integrated
into the shopfront.
Highway authorities do not have specific powers to erect bollards,
nor is this always an appropriate or desirable solution to the
problem of ramraiding, particularly in individual cases. The
majority of modern retail units have full height windows designed
to maximise display but which make them very vulnerable. The
traditional shopfront with its reduced area of glass and reinforced
stall riser is more resistant to attack. The installation of
external or internal shutters or grilles and the use of laminated
glass will also afford added protection. Where a highway is subject
to redesign or improvement, any preventative measures to reduce the
incidence of ramraiding can be incorporated where
appropriate.
Note: UDP Policy DCD1.6 deals in general terms with safety and
security issues.
33
a) Stockport MBC – Environment and Economic Development Division,
Development Control Section
Development Control Section Environment and Economic Development
Division Hygarth House 103, Wellington Road South Stockport SK1
3TT
Telephone Numbers/e-mail addresses for Development Control
Officers
Bramhall 0161 474 3540 west.dc@stockport.gov.uk (Bramhall,
Woodford, part Hazel Grove, part Cheadle Hulme)
Cheadle 0161 474 3538 west.dc@stockport.gov.uk (Cheadle, Gatley,
Heald Green, part Cheadle Hulme)
Four Heatons 0161 474 3551 west.dc@stockport.gov.uk (Heaton Moor,
Heaton Mersey, Heaton Norris and Heaton Chapel, part Reddish)
Heath Bank 0161 474 3550 west.dc@stockport.gov.uk (Edgeley, Cale
Green, Davenport)
Marple 0161 474 3657 east.dc@stockport.gov.uk (Marple, Mellor, High
Lane)
Stepping Hill 0161 474 3543 east.dc@stockport.gov.uk (Offerton,
part Hazel Grove, Great Moor, Stepping Hill, Higher Hillgate)
Tame Valley 0161 474 3656 east.dc@stockport.gov.uk (Stockport Town
Centre, part Reddish, Brinnington, Lower and Middle Hillgate)
Werneth 0161 474 3544 east.dc@stockport.gov.uk (Romiley, Bredbury,
Woodley, Compstall, Werneth Low)
IMPORTANT: PLEASE NOTE THAT AN ANSWERPHONE SYSTEM IS IN OPERATION
FOR PART OF THE DAY. IF YOU WANT TO SPEAK TO A DEVELOPMENT CONTROL
OFFICER PLEASE RING BEFORE 10.30 AM
34
OR AFTER 3.00 PM MON-FRI ONLY.
If you would like to meet a planning officer to discuss your
proposals you are STRONGLY ADVISED TO MAKE AN APPOINTMENT. Planning
Officers spend a significant amount of their time out on site
visits, so may not always be available when you call.
SMBC ENVIRONMENT AND ECONOMIC DEVELOPMENT DIVISION RECEPTION,
HYGARTH HOUSE
The Reception area is open to the public at the following
times:
8.30am – 5.00pm Monday – Thursday
8.30am – 4.30pm Friday
CLOSED Saturday/Sunday/Bank Holidays
Application forms and copies of the Council’s planning policies
(Unitary Development Plan and Supplementary Planning Guidance etc.)
are available at Reception.
Current and historic planning applications are also available for
viewing at Reception.
If you would like to view a particular planning application it is
best to telephone with the details in advance in order to give the
administrative staff time to retrieve the application from the
filing system before you arrive.
b) Stockport MBC – Environment and Economic Development Division,
Policy Section
For specific queries about the content of this Supplementary
Planning Guidance and related UDP policies, please ring the Policy
Section on 0161 474 3534, or e- mail
geoffrey.taylor@stockport.gov.uk
c) Stockport MBC – Environment and Economic Development Division,
Building Control Section
Building Control Section Environment and Economic Development
Division Hygarth House 103, Wellington Road South Stockport SK1
3TT
35
East Area Team
Brian Bentley MBEng Tel:- 0161-474-3568 Fax:- 0161-474-3572
Mobile:- 07748 632809 e mail:- brian.bentley@stockport.gov.uk
Heaviley, Great Moor, Offerton, Little Moor, Hazel Grove (North of
Torkinton Road)
David Timperley Tel:- 0161-474-3560 Fax:- 0161-474-3572 Mobile:-
07748 632812 e mail:- david.timperley@stockport.gov.uk Marple,
Marple Bridge,Compstall, High Lane, Hazel Grove (South of Torkinton
Road)
John Wall Tel:- 0161-474-3565 Fax:- 0161-474-3572 Mobile:- 07748
632808 e mail:- john.wall@stockport.gov.uk Brinnington, Bredbury,
Romiley, Woodley
Paul Pratten BA(Hons) MRICS MCIOB Tel:- 0161-474-3568
Fax:-0161-474-3572 Mobile:- 07748 632810 e mail:-
paul.pratten@stockport.gov.uk Reddish, Town Centre
Peter Gillooly MRICS Tel:- 0161-474-3560 Fax:- 0161-474-3572
Mobile:- 07748 632811 e mail:- peter.gillooly@stockport.gov.uk
Hazel Grove (East of A6), Norbury Moor, Bramhall East
36
West Area Team
Alan Finney MRICS West Area Building Control Officer Tel:-
0161-474-3553 Fax:- 0161-474-3572 Mobile:- 07748 632802 e mail:-
alan.finney@stockport.gov.uk
Arthur King MBEng Tel:- 0161-474-3565 Fax:- 0161-474-3572 Mobile:-
07748 632807 e mail:- arthur.king@stockport.gov.uk Heaton Chapel,
Heaton Mersey, Heaton Moor, Heaton Norris
Brian Moss MRICS Tel:- 0161-474-3562 Fax:- 0161- 474-3572 Mobile:-
07748 632803 e mail:- brian.moss@stockport.gov.uk Woodford,
Bramhall West, Cheadle Hulme South
Irvine McKee MBEng ACIOB Tel:- 0161-474-3562 Fax:- 0161-474-3572
Mobile:- 07748 632806 e mail:- irvine.mckee@stockport.gov.uk
Gatley, Heald Green
Paul Britner MBEng Tel:- 0161-474-3554 Fax:- 0161-474-3572 Mobile:-
07748 632804 e mail:- paul.britner@stockport.gov.uk Shaw Heath,
Adswood, Woodsmoor, Cheadle Heath, Edgeley, Davenport
Paul Farrell MBEng Tel:- 0161-474-3554 Fax:- 0161-474-3572 Mobile:-
07748 632805 e mail:- paul.farrell@stockport.gov.uk Cheadle,
Cheadle Hulme North, Bramhall East
37
d) Other contacts and information
English Historic Towns Forum PO Box 22 Frenchay Bristol BS16
1RZ
Tel. 0117 975 0459 Fax. 0117 975 0460 e-mail: ehtf@uwe.ac.uk
website: www.historic-towns.org/ehft
Publications include:
ii) Details and Good Practice in Shopfront Design (1993)
iii) Shopfronts Security Report (1994)
Timber Research and Development Association (TRADA) Stocking Lane
Hughenden Valley High Wycombe Buckinghamshire HP14 4ND
TRADA helpline: 01494 569601 e-mail: information@trada.co.uk
website: www.trada.co.uk
Publications include:
i) Wood Information Sheet 2/3 Sheet – 10 - “Timbers, their
Properties and Uses”
ii) Wood Information Sheet 2/3 Sheet – 6 - “Wood Decorative and
Practical”
38