Post on 20-Jul-2020
Squaring the Circle
Overlooked Nestler Models
Word Games
Word association has become fashionable: “if you were an animal, what
would you be?” Largely, apart from as a word game, the concept is a job
interview gimmick of little scientifically proven significance. However, I do
subconsciously make word associations with certain slide rule makers.
Pickett is always remembered as the maker of
the slide rule that went to the moon with the
Apollo missions. But idiosyncratically certain
shapes of slide rules are, for me, synonymous
with a particular make of slide rule. For any
circular model the Dutch maker ALRO always
springs into mind. Anything duplex and I think
of the German maker Faber-Castell and for
any drum type, the Swiss maker LOGA. That
just leaves the rectilinear models. These I always associate with the
German maker Nestler. So when I came across a circular Nestler it
struck me as odd.
Nestler’s Rectilinear Heritage
For my rectilinear association there were other worthy candidates such as
makers ARISTO or A.G. Thornton. I “choose”
Nestler because they were the only maker who
had dividing engines that could incise linear
scale lengths of up to 100cm. They were the
“Kings” of the classic wood and celluloid
veneered linear slide rule. They produced
around 300 different rectilinear wood and
plastic models in ten different stock lengths
ranging from 10 to 100cm. So when I came
across a round plastic Nestler I just assumed I
had never seen one before. Nevertheless my
“wrong looking” circular Nestler intrigued me.
To my surprise the plot quickly thickened as no
circular models are listed for Nestler in either of the standard reference
works from Hopp or Von Jezierski [2, 3]. They were also missing from my
Nestler catalogue from 1931 [4]. The catalogue was obviously too early
MB Word Association
board game
Nestler Dividing Engine [1]
for any plastic model but there was also no mention of any circular
models in the themed books on Nestler by Craenen [5, 6] or in any
published Nestler-related article. So my circular Nestler must have a story
to tell.
Nestler’s Circular Heritage
Initial research soon revealed that other Nestler branded circular models
existed. However, this still did not explain their scarcity and why they
have been overlooked. After some more digging a more familiar story
slowly emerged.
Nestler sold circular models but never considered them part of their retail
slide rule product range. This is why no circular model was ever listed in
any Nestler catalogue [7]. This is not an unfamiliar story as many makers
often resold or rebranded complementary slide rules from a third party or
an OEM supplier alongside their own published range. But this is not true
of Nestler. In their factory in Lahr they had the technical staff and the
equipment to make any form of slide rule in-house - i.e. rectilinear,
drum/cylindrical or circular/disc. In contrast, although rarely mentioned,
the 3 drum models (Ø 5.5, 9 and 16cm) Nestler made were listed [4] in
their catalogues (model numbers 44, 44a and 45 but post 1955
renumbered to 0441, 0442 and 0443). All the Nestler circular models
were specially commissioned production runs. By not openly publishing
their special commissions Nestler mirrored their German rival Faber-
Castell. Until published in the book by Holland [8] the specially
commissioned models made by Faber-Castell were also largely unknown.
Nestler’s Circular Slide Rules
Although world renowned for their slide rules, Nestler also successfully
retailed a rich product portfolio of drawing, drafting and surveying
equipment [4]. Consequently they had an extensive and varied customer
base. So whenever a valued customer approached Nestler with a special
commission for a circular slide rule it made good commercial sense to
arrange a low volume special production run.
All such specially commissioned circular models carry the Nestler brand
name and the company name/logo of the customer. The known examples
fall into one of four distinct categories:
1. Military
2. Regular
3. Special
4. Unofficial “co-branding”
However, regardless of the category, all the circular models were made
from Anagit1 plastic and produced in the 1960s.
The Military Models:
Nestler was a long-standing supplier to the German “Bundeswehr” and
the two known circular examples from this category were made for the
German Armed Forces. Their military provenance is confirmed by both
models displaying a 13-digit NATO or National Stock Number (NSN)
identifying code - the 5th and 6th digits2 being “12” for Germany. Such
NSN’s identify a unique item of supply across the globe. However, the two
circular examples are significantly different in style, size and scope.
The pocket Ø 10.2cm thin red and white duplex model is an Atomic,
Biological and Chemical (ABC) calculator3. The Fission Fragment Fallout
Decay And Dose Guide calculates the dangers from nuclear radiation
fallout after an atomic explosion. A table on the back includes
compensation/reduction factors specifically for the military - e.g. for
armed forces personnel in a foxhole or in an armoured tank at the time of
an explosion.
Pocket Ø 10.2cm ABC Radiation Calculator – NSN 6665-12-136-1506
The second and much larger Ø 31.5cm black-and-white
Hoehenwindmessung desktop model has a distinctively more armed
forces look and feel. The rugged High Altitude Calculator comes in two
“industrial-strength” versions – both with two independently working
sturdy chrome and plastic cursors. Unsurprisingly when it is not in use the
calculator was protected by a dark-green stitched heavy-duty linen pouch.
1 Nestler name (Albert Nestler AG) for injection moulded polystyrene. 2 National Codification Bureau (NCB) defined 2-digit country code number. 3 Design, without an NSN number, also reused for non-military customers.
Desktop Ø 31.5cm High Altitude Calculator
NSN 6660-12-127-6307 NSN 6660-12-140-6737
Both versions date from 1969 and are in essence modern adaptations of a
traditional Artillery Range Finder slide rule or graphic plotter. The layout
of NSN version ending in 6307 includes a scale classically calibrated into
360 degrees - “Winkel in Grad”. On the NSN version ending in 6737 the
scale is calibrated in the more military favoured milliradians4 (MILS) –
“Winkel in Strich”. A modern version was needed because “battlefield
distances” are now global. But having such a late production date the
possible use by the military is speculative. The late 1960s is still the era
of the first Cold War between the Soviet Union and the United States and
its Western Allies. So these calculators could have been used to plot
incoming or outgoing missile trajectories. However, they could equally
and more benignly have been used as a latter-day “Pilot Balloon” slide
rule to track the likes of the jet stream and its effect on missiles or planes
flying at high altitude [9].
The Regular Models:
Although any circular model was made to order, Nestler saw the economic
sense of having “ready” an off-the-shelf pre-engineered offering and a
standardised instruction leaflet. Customers could choose between: (i) a
large Ø 13cm circular RL 130 model or (ii) a pocket Ø 7.5cm circular RP
75 model [7]. Both had a green and white colour scheme and a limited
complement of scales – none of which were trigonometric. The name
4 For NATO countries (but excluding the UK) a circle divided into 6400 mils.
and/or logo of the commissioning company were put on the
accompanying pouches.
Ø 13cm Mannheim-like RL 130 Ø 7.5cm Rietz-like RP 75
The larger Mannheim-like RL 130 did include an extra % scale and the
back of the cursor innovatively doubled up as a clip for a jacket or shirt
pocket. The pocket RP 75 came in two versions. A Rietz-like layout for
engineers and a basic C / D,% layout for merchants [10].
The Special Models:
Inevitably some non-military customers needed a bespoke circular slide
rule with trade or company-specific scales. Such commissions were in
essence “one-offs”. The first known example is an impressive multi-
coloured duplex circular model made for the Frauenfeld based Swiss
company Peter Hefti AG.
Large Ø 13cm duplex Kreisrechner
In the 1960s Hefti supplied made-to-order continuous drive belts for
industrial belt-driven machines. Using both sets of the scales a customer
could reliably calculate the exact-sized drive belt they needed to order
[7]. Undoubtedly there are more but at least two other known bespoke
examples were made:
Pocket Ø 10.5cm Total Strahlenschutz Large Ø 13cm Disc-O-Lator
The German multi-coloured pocket Strahlenschutz is a non-military
version of an ABC atomic fallout calculator. Brief instructions were printed
on the back but the thin grey cardboard wallet it came in also included a
full instruction booklet. It was first commissioned by the Ladenburg based
Total KG Foerstner & Co. The company is famous for its range of fire
extinguishers but later became part of Automation und Messtechnik
GmbH. The Strahlenschutz design was then reordered and reissued under
the new company name [10].
The larger red and black Disc-O-Lator was made for Kienzle System. The
full company name was Kienzle Apparate GmbH. They were based in
Villingen, Germany and were a spinoff of the original Kienzle watchmaking
company. Kienzle Apparate GmbH specialised in instrumentation such as
tachographs for commercial vehicles. The Disc-O-Lator was an aid for
calculating the driving/working hours recorded on a tachograph’s
replaceable paper discs [11].
The “Co-branded” Models:
The models in this category are especially novel. Seemingly Nestler
decided to market two circular models in collaboration with fellow German
slide rule maker Controller-Calculator KG based in Munich. Two of
Controller-Calculator’s distinctive aluminium models, the 75 R (Ø 7.5cm)
and 110 R (Ø 11cm), were repackaged in a black plastic pouch featuring
both company names and a set of instructions from Nestler. But these
models are not what they seem and have nothing to do with Albert
Nestler AG.
“Co-branded” pocket Ø 7.5cm Nestler/Controller 75 R
The clue to the true provenance of these models is the address listed at
the end of the instructions: Baden Baden. This should have been Lahr
but a grandson of the founder of Nestler, Albert Nestler Jr., tellingly lived
in Baden Baden. Also the company name listed is: Albert Nestler
Handelesgesellschaft mbH. Albert Nestler Jr. was not involved in running
his grandfather’s company although he was a local Nestler sales
representative for the Baden Baden area. The counterfeit
Nestler/Controller models were a private marketing initiative. Albert
Nestler Jr. had some plastic pouches and sets of instructions printed
which he paired up with two existing aluminium circular slide rules from
Controller-Calculator. He was piggybacking on the established Nestler
name and brand. It was done without Nestler’s permission and probably
without Controller-Calculator permission. There was never any form of
cooperation or collaboration between Nestler and Controller-Calculator or
between Nestler and any other slide rule maker [7].
The Square Is Now Round
In Nestler’s case their circular models were literally all exceptions to the
rule and defied the company’s rectilinear profile. Being specially
commissioned they were all made in ad-hoc production runs in the 1960s.
Sales volumes would have been low and this is probably why they have
been overlooked in the past. Therefore any of the genuine Nestler circular
models are uncommon and are worth looking out for. But do not be
misled by any Nestler circular model purporting to be co-branded with
slide rule maker Controller-Calculator. Good hunting!
Acknowledgements And References
I am especially grateful to Jürgen Nestler, the great-grandson of the
founder of Albert Nestler AG. His willingness to answer my many
questions and to share his company and family knowledge were
instrumental in finding the true provenance of the overlooked Nestler
circular slide rules. I am also indebted to fellow collectors Hans Peter
Schaub, Peter Holland and John Hunt Snr. for their help with some of the
details.
1. TECHNOSEUM: Landesmuseum für Technik und Arbeit, “Galerie der
Objekte”, Germany - www.technoseum.de/ .
2. Hopp, Peter M.: “Slide Rules Their History, Models and Makers”,
Astragal Press, ISBN 1-879335-86-7, 1999.
3. Von Jezierski, Dieter: “Slide Rules A Journey Through Three
Centuries”, Astragal Press, ISBN 1-879335-94-8, 2000.
4. Albert Nestler AG: “Spezialfabrik für Rechenschieber aller Systeme -
Sämtliche Zeichennutseilen Mess- und Nivellier-Latten“, catalogue from
1931.
5. Craenen, Guus: “Albert Nestler Innovation und Qualität – Die
Rechenstäbe von Nestler in ihrem internationalen Umfeld”, private
publication (out of print), 2001.
6. Craenen, Guus: “Albert Nestler Innovation und Qualität –
Zusammenarbeit mit anderen Herstellen und mit Erfindern”, private
publication (out of print), 2004.
7. Private correspondence with Jürgen Nestler, Germany, 2019.
8. Holland, Peter: “Slide Rules – A.W. Faber & A.W. Faber-Castell”, 7th
edition, private publication (out of print), 2014.
9. Private correspondence with John Hunt Snr., England, 2019.
10. Private correspondence with Hans Peter Schaub, Switzerland,
2019.
11. Private correspondence with Peter Holland, Germany, 2019.