Submittal / Substitution Request

Submitted tO:To: ______________________________________________________________________________Firm: ____________________________________________________________________________Project: __________________________________________________________________________Submitted Product: SimpSOn StrOng-tie StrOng-bOLt 2 Wedge Anchor for Cracked and Uncracked ConcreteSpecified Product: ___________________________________________________Section: ________________ Page: _______________ Detail/Sheet No.: ______________________Description of Application: ____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Attached information includes product description, installation instructions and pertinent technical data needed for evaluation of the submittal request.

Submitted by:Name: ____________________________________ Signature: _____________________________Firm: ____________________________________________________________________________Address: _________________________________________________________________________ _________________________________________________________________________Phone: ____________________________________ Fax: __________________________________E-Mail: ___________________________________________________________________________Date of Submittal: ___________________________

FOr Architect/engineer uSe:Approved: ______ Approved As Noted: ______ Not Approved: ______(Please briefly explain why not approved)___________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

By: _______________________________________ Date: _________________________________Remarks: _____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SIMPSON STRONG-TIE COMPANY INC. 1

Table of Contents

2

ThisproductsubmittalwascompiledbytheSimpsonStrongTieSubmittalGeneratorwebappandiscurrentasof8/3/2015.Informationincludedinthissubmittalissubjecttochange;seewww.strongtie.comforthelatestinformation.

SimpsonStrongTieStrongBolt2WedgeAnchorCatalogInformationProductInformationAllowableStrengthDesign(ASD)DatainMasonry

IAPMOUESER240(forConcreteMasonry)

CityofLosAngelesResearchReportRR25936(forConcreteMasonry)

UnderwritersLaboratories(UL)FileEX3605

FactoryMutual(FM)Listing

MechanicalAnchorsSafetyDataSheet

Mec

hani

cal A

ncho

rs

The Strong-Bolt 2 wedge anchor is the next-generation solution for cracked and uncracked concrete. Following rigorous testing according to ICC-ES acceptance criteria, the Strong-Bolt 2 anchor received classification as a Category 1 anchor, the highest attainable anchor category for performance in cracked concrete under static and seismic loading. Available in stainless steel, it is code-listed by ICC-ES under the 2009 IBC requirements for post-installed anchors in cracked and uncracked concrete.

FEATURES: Category1anchorclassification: The Strong-Bolt2 anchor received classification

as a Category 1 anchor, which is established by performance in reliability tests in accordance with AC193 and ACI355.2 test criteria. Category 1 is the highest attainable anchor category for reliability.

Tri-segmentedclip: Each segment adjusts independently, increasing follow-up expansion should the hole increase in size as a result of a crack

Dualembossmentsoneachclipsegment: Enables clip to undercut into the concrete thereby increasing follow-up expansion should a crack occur

The38"anchorsolutionapprovedfor314"concretethickness: The Strong-Bolt2 anchor can be installed in cracked concrete with a minimum thickness of 3 ", including concrete-over-metal decking

High-strengthalloycliponcarbon-steelanchors: This special alloy clip offers improved performance

Standard(ANSI)fractionalanchor: Fits most fixtures and installs with common drill bit sizes and tools

Type316stainless-steelcliponstainlesssteelanchors: In addition to superior corrosion resistance, a stainless-steel clip offers memory that contributes to the anchors performance if the hole increases in size because of a crack

MATERiAl: Carbon-steel stud with special alloy clip; stainless-steel stud with stainless-steel clip

FINISH: Zinc-plated (carbon steel)

CODES: ICC-ES ESR-3037 (carbon and stainless steel in concrete); IAPMO ES ER-240 (carbon steel in CMU); City of Los Angeles RR25891; Underwriters Laboratories File Ex3605; Factory Mutual 3043442; Florida Pending

TEST CRiTERiA:The Strong-Bolt2 wedge anchor has been tested in accordance with the ICC-ES Acceptance Criteria for Mechanical Anchors in Concrete Elements (AC 193) and ACI 355.2 for the following: Static tension and shear loading in cracked and uncracked concrete

Seismic and wind loading in cracked and uncracked concrete

Performance in cracked concrete

Performance in lightweight concrete over metal deck

iNSTAllATiON: DonotuseanimpactwrenchtosetortightentheStrong-Bolt2anchor. Caution: Oversized holes in the base material will make it difficult to set the anchor and will reduce the anchor's load capacity.

Drillaholeinthebasematerialusingacarbidedrillbitthesamediameterasthe nominaldiameteroftheanchortobeinstalled.Drilltheholetothespecified embedment depth and blow it clean using compressed air. Overhead installations need not be blown clean. Alternatively, drill the hole deep enough to accommodate minimum hole depth and dust from drilling.

Assembletheanchorwithnutandwashersothatthetopofthenutisflush with the top of the anchor. Place the anchor in the fixture and drive into the hole until washer and nut are tight against the fixture.

Tightentotherequiredinstallationtorque.

DESiGN EXMPlE: See pages 233234

LengthIdentificationHeadMarksonStrong-Bolt2WedgeAnchors(correspondstolengthofanchorinches)Mark Units A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

From in. 1 12 2 2 12 3 3 12 4 4 12 5 5 12 6 6 12 7 7 12 8 8 12 9 9 12 10 11 12 13 14 15 16 17 18

UpToButNotIncluding in. 2 2 12 3 3 12 4 4 12 5 5 12 6 6 12 7 7 12 8 8 12 9 9 12 10 11 12 13 14 15 16 17 18 19

InstallationSequence

Strong-Bolt2WedgeAnchor

Simpson Strong-Tie Anchoring and Fastening Systems for Concrete and Masonry

C-SA

S-20

12

2012

Sim

pson

Stro

ng-T

ie C

ompa

ny In

c.

96

StrongBolt2 Wedge Anchor for Cracked and Uncracked Concrete

Mechanical Anchors

CarbonSteel-ZincPlated1

ComponentMaterials

AnchorBody Nut Washer Clip

Carbon Steel

Carbon Steel

ASTM A 563, Grade A

Carbon Steel

ASTM F844

Carbon Steel ASTM A 568

1. Zinc meets ASTM B 633, Class SC 1 (Fe / Zn 5), Type III.

StainlessSteel

ComponentMaterials

AnchorBody Nut Washer Clip

Type 316 Stainless Steel

Type 316 Stainless Steel

Type 316 Stainless Steel

Type 316 Stainless Steel

MaterialSpecifications

1. TheinformationpresentedinthistableistobeusedinconjunctionwiththedesigncriteriaofACI318AppendixD.2. The clearance must comply with applicable code requirements for the connected element.3. For the 2006 IBC, do replaces da.4. For the 2003 IBC, fut replaces futa.

Strong-Bolt2AnchorProductData

Size(in.)

CarbonSteelModelNo.

316StainlessSteel

ModelNo.

DrillBitDia.(in.)

ThreadLength(in.)

Quantity

Box Carton

38 x 2 34 STB2-37234 STB2-372346SS 38 1 516 50 25038 x 3 STB2-37300 STB2-373006SS 38 1 916 50 25038 x 3 12 STB2-37312 STB2-373126SS 38 2 116 50 25038 x 3 34 STB2-37334 STB2-373346SS 38 2 516 50 25038 x 5 STB2-37500 STB2-375006SS 38 3 916 50 20038 x 7 STB2-37700 STB2-377006SS 38 5 916 50 20012 x 3 34 STB2-50334 STB2-503346SS 12 2 116 25 12512 x 4 14 STB2-50414 STB2-504146SS 12 2 916 25 10012 x 4 34 STB2-50434 STB2-504346SS 12 3 116 25 10012 x 5 12 STB2-50512 STB2-505126SS 12 3 1316 25 10012 x 7 STB2-50700 STB2-507006SS 12 5 516 25 10012 x 8 12 STB2-50812 STB2-508126SS 12 6 25 5012 x 10 STB2-50100 STB2-501006SS 12 6 25 5058 x 4 12 STB2-62412 STB2-624126SS 58 2 716 20 8058 x 5 STB2-62500 STB2-625006SS 58 2 1516 20 8058 x 6 STB2-62600 STB2-626006SS 58 3 1516 20 8058 x 7 STB2-62700 STB2-627006SS 58 4 1516 20 8058 x 8 12 STB2-62812 STB2-628126SS 58 6 20 4058 x 10 STB2-62100 STB2-621006SS 58 6 10 2034 x 5 12 STB2-75512 STB2-755126SS 34 3 316 10 4034 x 6 14 STB2-75614 STB2-756146SS 34 3 1516 10 4034 x 7 STB2-75700 STB2-757006SS 34 4 1116 10 4034 x 8 12 STB2-75812 STB2-758126SS 34 6 10 2034 x 10 STB2-75100 STB2-751006SS 34 6 10 20

CarbonSteelStrong-Bolt2WedgeAnchorInstallationInformation1

Characteristic Symbol UnitsNominalAnchorDiameter

CarbonSteel38inch 12inch 58inch 34inchInstallationInformation

NominalDiameter da3 in. 38 12 58 34DrillBitDiameter d in. 38 12 58 34

BaseplateClearanceHoleDiameter2 dc in. 716 916 1116 78 Installation Torque Tinst ft-lbf 30 60 90 150

NominalEm