Post on 25-Nov-2015
description
1BP0830801
INSTALLATION MANUALApplied Machine: /
/
I. Outline bizhub 184Follow the nomulti bypass Note:
For the dmulti bypand perfo
Once theit off until
When traadequate(the printe
This manprinter anslightly dcase, instance of ydure. Thchange oof Installation Procedures for/bizhub 164 tes below to install the printer and thetray.
etailed installation procedures for theass tray, see the Installation Manual,rm the procedures correctly. power switch is turned on, do not turnthe installation has been completed.nsporting or moving the printer, assign number of persons r mass: 23.5 kg/52 lb).ual provides the illustrations of thed the accessory parts that may be
ifferent in shape from yours. In thatead of the illustrations, use the appear-ours to follow the installation proce-is does not cause any significantr problem with the procedure.
II. Installation Space (unit: mm (inch))bizhub 164 + MB-503
III. Pre-installation Check Items1. Install the printer at a horizontal and stable place.2. Be sure to use a power source of the voltage and
frequency indicated in the product specifications.Ensure that the current carrying capacity of thepower outlet is at least equal to the current listedin the product specifications.
3. Power the printer directly from a dedicated poweroutlet. (Do not use an extension cord.)
4. Do not plug or unplug the power cord with wet ordirty hands, otherwise you may get an electricshock.
5. Avoid a hot and humid environment, or a placeexposed to direct sunlight.
6. Avoid a dusty location, or a place near volatileand flammable substances.
7. Avoid a poorly ventilated place.
A0XXIXC001MA
A0XXIXC002MA
449(
17-2
1/32
)
200(8)
928 (36-1/2)783 (30-13/16)
607 (23-7/8)
570 (22-7/16)
530 (20-7/8)
856
(33-
11/1
6)
927 (36-1/2)E-1 A0XX-9630-00
IV. Accessory Parts
* Varies deparea.
V. Unpacki1. Unpack th
ing materia2. While kee
printer fromNote:
Printer masWhen transadequate n
VI. Removing Protective Tape, PackagingMaterials and Imaging Unit1. Remove pieces of protective tape and packaging
materials.
No. Name Qty
1. Users Guide* 1 set2. Installation Manual (this manual) 13. Toner bottle* 14. Starter 15. Power c6. Power c7. CD-RO
AftepacthePutdanE-2
ending on the applicable marketing
ng the Printere packaging box, and remove cushion-ls and plastic bags from the box.ping the printer level, take out the the box.
s: 23.5 kg/52 lbporting or moving the printer, assign
umber of persons.
2. Open the right and front doors.3. Remove the cover shown in the illustration and
unplug the connector (one screw).
ord 1ord instruction* 1
M* 1 set
r unpacking, be sure to get rid of thekaging materials and keep them out of reach of children.ting your head in the wrapper involvesger of suffocation. A0XXIXC004MA
A0XXIXC005MA
A0XXIXC007MA
A0XXIXC008MA
4. Unscrew the screws shown in the illustration toremove the imaging unit (two screws).
Note: Do not touch or scratch the PC drum. Cover the imaging unit, which has been
removed, with a protective cloth or similar mate-rial.
5. Close the f6. Remove th7. Push the s
remove throller.
8. Close the r
9. Slide out the drawer and remove the protectivetape and cushioning material.
StarterE-3
ront door.e protective tape.hafts in the direction of the arrows toe fixing brackets that fix the transfer
ight door.
10. Slide the drawer back in.
A0XXIXC012MA
A0XXIXC011MA
A0XXIXC006MA
VII. Loading the Starter1. While pressing the connector tabs, push out the
connector from the imaging unit.
2. Unscrew tunit, and slightly oparea) of th
Note: Do not op
charger m Do not to Cover th
removed,rial.
3. Remove the developing unit cover (threescrews).
DevelopinE-4
he screws that secure the PC drumthen take out the PC drum unit byening the lower part (the shadowede PC drum unit (five screws).
en the lower part wide, otherwise theay drop.
uch or scratch the PC drum.e PC drum unit, which has been with a protective cloth or similar mate-
4. Ready a packet of the starter and cut off one cor-ner of the aluminum packet with scissors.
5. While turning the gear in the direction of thearrow, pour the starter evenly into the developerchamber.
Note: Turn the magnet roller in the direction of its nor-
mal rotation, and not the backward. Be sure not to let the starter get inside the collar.
6. Reinstall the developing unit cover, ensuring thatits tabs are fitted properly into the slits (threescrews).
Note:Do not tilt the developing unit or imaging unit afterthe starter is poured.
A0XXIXC040MATabs
A0XXIXC013MA
PC drum unit
g unit
A11UIXC014MA
A11UIXC015MA
Collar
A11UIXC016MA
Temporarily tighten the screw first.
7. Install the front of the PC drum unit first, and thenthe rear part. Then, secure the screws (fivescrews).
Note: Do not open the lower part wide, otherwise the
charger may drop. Clean the screw groove before securing them. Do not touch or scratch the PC drum.
8. Attach the in step 1.
9. Slide the isecure the
Note: Make sur
ing the im Align the
of the prin
10. Plug the connector, and then attach the cover(one screw).
Temporarilythe screw fiE-5
imaging unit connector that is removed
maging unit into the printer, and then screws (two screws).
e that the right door is open when slid-aging unit into the printer.shaft of the imaging unit with the guideter.
11. Close the right and front doors.12. Plug the power cord to the printer, and then to a
power outlet.
VIII. ATDC Adjustment1. Turn on the power switch.2. Enter the service mode on the display.
(Refer to the Service Manual to display the ser-vice mode screen.)
3. Press [+] or [-] key to select FUNCTION on thedisplay.
4. Press the [Menu/Select] key.5. Press the [+] or [-] key to select TCR AUTO
ADJUST.6. Press the [Menu/Select] key to execute the ATDC
adjustment.The following message appears in two minutes.TCR AUTO ADJUSTTCR GAIN: ***
7. Turn off the power switch.
A0XXIXC017MA
tightenrst.
Temporarily tightenthe screw first.
A0XXIXC019MA
A0XXIXC008MA
IX. Installing the Toner BottleNote:
A toner bottle may not be shipped with yourprinter. If not, purchase one that is separatelyavailable.
1. Shake the toner bottle well about five times in thevertical direction. Then, turn it over and repeatthe same p
Note:The toner cperform this
2. Open the f3. Insert the
up, and the
4. Aligning thmark, inse
5. Check thathen turn arrow to lo
6. Close the
TapeE-6
rocedure.
an cake in the toner bottle. Be sure to procedure.ront door.toner bottle halfway with the tape siden slowly peel the tape off the bottle.
e tip of the bottle tab with the rt the toner bottle all the way in.t the toner bottle is all the way in, andthe toner bottle in the direction of theck it.
front door.
A0XXIXC018MA
A0XXIXC050MA