Post on 17-Apr-2022
Scrap Quality Specification Rev 11 September 2019
Document Manager: Kerry Ward
Approved by: Darren Wheeler
Note: This is considered an uncontrolled document unless it is being viewed on-line from the SharePoint or from a printed copy at one of the following controlled locations:
NONE
Page 2 of 16 TITLE: Scrap Quality Specification Revision 11
1.0 PURPOSE:
Novelis is a supplier to discerning customers of a wide variety of rolled aluminum products. Novelis’
visibility in these markets depends on its’ ability to consistently supply aluminum of the highest
quality. A major factor in our ability to meet this requirement is the quality of the raw material we purchase for our processes with scrap representing a meaningful percentage of our raw material mix.
It is for this reason that we have developed this manual, the major purpose being to communicate as clearly as possible, the Novelis requirements for high quality scrap for process. The philosophy of
Novelis is to work with all of its suppliers to enable them to continuously improve the quality of
materials delivered.
2.0 GENERAL SAFETY GUIDELINES
2.1 Water poses a MAJOR EXPLOSION RISK when combined with molten metal. All forms
of scrap that have potentially been introduced to water, or the following: containers,
or bottles, crimped tubing and other closed containers, water filled bales,
fiber/cardboard cored coils, desiccant, paper interleaved coils and wrapped coils/bales
are all common hiding places for water in some form or another; incoming loads
containing any of these items are subject to rejection.
2.2 Other causes of explosion may occur, so all scrap must be clean and free of fertilizers,
explosives, aluminum fines, nitrates, sulfates, oxidizers, butane lighters, welding
equipment, propane tanks, unknown powders, salts, dross, excessive mold release
agents, pot room bath, corrosion, dirt, gravel, volatile substances, non-aluminum
contaminants, closed containers, crimped tubing, PCB’s, radioactive materials and
aluminum-lithium alloys, and other flammable materials. Any loads containing these
or other questionable substances are subject to rejection.
2.3 Unloading dock safety is also critical. Many of the same requirements to ensure a
quick unloading are the same for safety. In addition to the previous requirements,
shifted loads, any material that has stored mechanical energy (springs or compressed
gasses) or has sharp edges protruding from the bundle are all examples of
unacceptable material. Any scrap that is loaded in an unsafe manner will be rejected.
2.4 Containing Scrap Safely
a) All pieces of scrap should be individually self-contained. Loose sheet, unbound
coils and broken bales are examples of unacceptable loads. b) All material should be loaded and secured to ensure orderly shipment. Tipped-
over sows and broken or double-stacked cardboard boxes or skids are
examples of unacceptable loads that will be rejected. c) The load must also be of a form to ensure that unloading does not take more
than the amount of time allotted for the unloading appointment. Sows with no
accessible fork pockets as well as a load with many small, unmanageable
pieces/coils are examples of loads subject to rejection.
Page 3 of 16 TITLE: Scrap Quality Specification Revision 11
d) Bales may be stacked as long as the weight of each stack of bales is (see 4.2
for weights of single bales):
Less than 11,500 lbs. for Oswego
Less than 8,000 lbs. for Berea and Greensboro The stack must have enough clearance to unload without damaging
the truck.
e) Plastic or fiber banding is to be used on all scrap returned from external tolling
facilities.
2.5 Coatings can cause excessive flaring and damage pollution controls. Hence , oils and process lubes are limited to 1% by weight of the scrap. Painted, lacquered or coated
scrap is also not acceptable.
2.6 Labeling of the proper chemical analysis is critical to the final properties of our end
product. Thus, any individual piece or bundle of scrap must be composed of a single
alloy or a known and acknowledged alloy grouping.
a) The alloy or grouping must be clearly and permanently identified on the scrap
along with the gross, tare, and net weight. Any grouping must be reviewed on
a regular basis as defined by the agreement and procedure. Label types
include spray paint, ink, stickers, markers, packing slips, wired tags, or heat
resistant crayon.
b) Each ingot, bundle, sow, or coil must be marked legibly and permanently with:
a. Manufacturers heat number b. The 4 digit AA alloy code or Novelis equivalent c. The piece weight
c) The pieces and bundles must be marked with only one alloy, and the alloy on
the product must match the alloy on the paperwork.
d) In the event that the plant has given direction to label material with a certain
alloy, the alloy and the paperwork must both match the designation the plant
has given. If the material was previously labeled with a different designation,
please remove or cross off the old designation from the material and write,
sticker, or tag the new plant directed designation on the material.
3.0 CONTAMINANTS
3.1 The presence of the following items may cause reason for rejection:
a) Paper
b) Plastic c) Iron/Steel
d) Batteries
e) Rocks/Dirt/Sand/Glass/Dross f) Rubber
g) Foil/Pie Pans/Wood
h) Oxides (i.e. rust and corrosion) i) Excessive Oils or Process Lubricants
j) Unknown Powders or Residues
Page 4 of 16 TITLE: Scrap Quality Specification Revision 11
k) Closed Containers l) Insulated Beverage Containers
m) Aerosol Cans
n) Snow, Ice, or Frost o) Cadmium Sulfide (Photocopier Drums)
p) Rusted Banding
4.0 Tier 1 Certification
4.1 Novelis has a certification process that allows suppliers to provide us with scrap that
can be charged directly into our melters. In order to become tier 1 certified, an audit
process for contamination & moisture is administered. Once passed, suppliers with a
current approved tier 1 audit are able to ship direct charge material to Novelis. Please
reach out to your buyer for more information about becoming tier 1 certified.
5.0 FORM REQUIREMENTS
5.1 Briquette (Both tier 1 and non-tier 1 material)
a) Dimensional Range = 4” x 4” x 6” to 24” x 24” x 48” b) Density must be greater than 40 lbs. / cu. Ft.
c) Material is to be palletized and strapped with steel or fiber banding (no
other type of containment is allowed). d) The maximum size steel bands are .75”X .020” thick.
e) Iron sensitive alloys (such as 6111) require fiber banding.
Scrap Type Briquette
Label Location Scrap Surface
Paint X
Sticker X
Marker
Packing Slip X
Wired Tag X
Crayon
Page 5 of 16 TITLE: Scrap Quality Specification Revision 11
5.2 Bale (Tier 1 certified only)
a) Dimensional Range = 24” x 24” x 48” to 48” x 48” x 60”.
b) Density must be greater than 20 lbs. / cu. ft. c) Material is to be bound with fiber or steel banding (Iron sensitive alloys
such as 6111 require fiber banding).
d) Bales should not arrive on skids. e) Cardboard, sheet, plastic, or burlap wrapped bales, which do not allow for
visual inspection of the contents, will not be accepted.
f) Bale stacks should allow a minimum of 6 inches clearance to the roof of the trailer, and individual bales should weigh a max of 6,000 lbs.
g) Dump truck delivery must be specifically agreed to in the purchase order
and special arrangements must be made for delivery. h) Each bale must be individually marked with weight and alloy.
5.3 Bales (Non-tier 1) – Oswego only & must have preapproval from Oswego to ship these bales to Oswego a) Must adhere to all of section 4.2 above, except b. b) Bales that are composed of only individual pieces and are not more than
12” in the maximum dimension, and no more than ¼” thick , with a
density of up to 120 lbs. / cu. ft. c) Bales that are composed of pieces larger than 12” should have a density
of up to 80 lbs. / cu. ft. d) Laminations of stacked sheet within the bales need to be limited to 1” in
total thickness.
Scrap Type Bale
Label Location Scrap Surface
Paint X
Sticker X
Marker
Packing Slip X
Wired Tag X
Crayon
Page 6 of 16 TITLE: Scrap Quality Specification Revision 11
5.4 Boxed (Both tier 1 and non-tier 1 material)
a) Minimum weight per box is 1,200 lbs.
b) Maximum weight per box is 7,000 lbs. for Oswego, 6,000 lbs. for Berea, & 5,000 lbs. for Greensboro.
c) Boxes should be strong enough not to tear during the unloading process.
Any boxes that are wet or oil soaked will be rejected. d) All boxes must be securely banded to pallets.
e) Boxes may not be double stacked. Double stacked boxes will be rejected.
f) Boxes cannot be loaded “telescoped,” or stacked inside other boxes. g) Chips / clipped sheet can be delivered in cardboard boxes or in a dump
truck.
h) Maximum box size (including pallet) is 54”W x 50”L x 58” H i) Each Gaylord must be individually marked with weight and alloy.
5.5 Supersacks (Tier 1 certified only)
a) The preferred method for receiving 1350 EC chops in Greensboro only is
in supersacks. b) The plants receive material in supersacks only with prior plant approval. c) All supersacks must be banded to a pallet.
d) Supersacks cannot be double stacked.
e) Supersacks must be able to be opened for inspection upon arrival while banded to the pallet.
f) Each supersack must be individually marked with weight and alloy.
Page 7 of 16 TITLE: Scrap Quality Specification Revision 11
5.6 Heavy Gauge Spools/Edge Trim (Tier 1 certified only)
a) Heavy gauge spools should be bound with fiber or steel banding. b) Heavy gauge spools Heavy gauge spools can be spooled to sizes up to 6,000
lbs. c) Heavy gauge spools under 2,000 lbs. and of the same alloy should be
banded together. d) In Oswego, heavy guage spools should be loaded individually (not banded to
pup coils or to plate) in the nose of a common carrier van.
e) Spools can be strapped to the top of a pancake or cut coil. The pancake coil must be lying flat, and the spools should not go past the edge of the
pancake coil. The maximum weight for this bundle is 6,000 lbs.
f) Spools smaller than 1,000 lbs. and of the same alloy should be palletized, unless otherwise approved by the plant.
g) Spools cannot be larger than 6’ in diameter.
h) Spools cannot be banded to coils. i) Spools should not exceed the width of the pallet.
j) Each spool should be marked with the weight and alloy.
k) For Berea & Greensboro, spools banded to pallets should not exceed 48” in height.
l) For Oswego, individual spools cannot be larger than 6’ in dameter.
m) Spool bundles should allow a minimum of 6” clearance to the roof of the trailer.
5.7 Coils (Tier 1 certified only)
a) Dimensions: Width = 18” to 100”, ID Min = 6” and OD Max = 110.” b) Individual coils less than 24” wide must be shipped eye-to-the-sky, on a
pallet. c) Two coils can be banded together, standing up, provided their combined
overall width exceeds 35”. d) Max Weight: 40,000 lbs. when delivered to Oswego, eye-to-the-side and
6,000 when delivered to Berea and Greensboro. e) Unstable coils (collapsed ID) have a reduced max weight of 11,500 lbs.
and can only be accepted in Oswego. f) No steel or fiber cored scrap will be accepted. Aluminum cores are
accepted.
Scrap Type Coiled Edge Trim
Label Location Scrap Surface
Paint X
Sticker X
Marker
Packing Slip X , if Palletized
Wired Tag
Crayon
Page 8 of 16 TITLE: Scrap Quality Specification Revision 11
g) All coil wrapping (plastic & paper) must be removed prior to shipment.
Coil identification per Section 2.6 must be visible on the coil. h) Coils loaded on a flatbed or conastoga must be loaded eye-to-the-side.
Coils loaded in a van must be loaded shotgun. i) Any coils loaded on a flatbed or conastoga must be tarped at all times. In
the event that the driver untarps early and the material gets wet, it will
be rejected. j) Spliced coils are to be comprised of only 1 alloy, unless a mixing plan has
been developed and agreed upon in advance. k) For coils shipping internationally, reference section 4.16. l) Each coil should be marked with the weight and alloy.
5.8 Cut Coils (Tier 1 certified only) a) Cut coils may be banded to pallets if necessary for transporting. b) Max weight (with or without a pallet) = 11,500 lbs. when delivered to
Oswego and 6,000 when delivered to Berea or Greensboro. c) Unstable cut coils are to be baled or put in cardboard boxes on pallets. d) Spliced cut coils are to be comprised of only 1 alloy, unless a mixing plan
has been developed and agreed upon in advance. e) Bundled coils are to be comprised of the same alloy unless a mixing plan
has been developed and agreed upon in advance. f) No steel or fiber cored cut coils will be accepted.
5.9 Jumbo Coils (12,000 lbs. or more & tier 1 certified only) a) Please read section 4.6 for basic coil requirements. b) Jumbo coils can only be delivered to Oswego. c) Coils must be loaded eye-to-the-side so that a fork truck can safely remove
the coil without having to drive onto the truck. Please see the below photo
for properly loaded jumbo coils on a flatbed. d) Coils over 40,000 lbs. must be loaded shotgun and require special notice
and a plant approved appointment time (See Delivery Schedule, section
7.0). e) Coils must be covered so they do not get wet (inside a covered wagon,
canastoga, etc.). Coils loaded on flatbeds must be tarped all year long. f) Cardboard underlayment, slip mats, and coil braces are all acceptable.
However, the coil must be securely banded, bare, and free from packaging.
Scrap Type Coil
Label Location Consistent Face
Paint X
Sticker X
Marker X
Packing Slip X
Wired Tag
Crayon X
Page 9 of 16 TITLE: Scrap Quality Specification Revision 11
g) Coatings can cause excessive flaring and damage pollution controls.
Hence, oils and process lubes are limited to 1% by weight of the scrap.
Please note that excessive oils or process lubes dripping down the side of
a coil is grounds for rejection.
5.10 Flattened Pup Coils (Tier 1 certified only)
a) Coils should be banded together before being banded to the pallet. b) Maximum ID height after flattening: 4” c) Maximum height of the bundle of flattend pup coils: 4’ d) Bands should be placed through the ID of the top and bottom coils to
prevent the coils from sliding during transportation.
Scrap Type Bundled Cut Coil
Label Location Inner Wrap
Paint X
Sticker X
Marker X
Packing Slip X
Wired Tag
Crayon X
Scrap Type Bundled Cut Coil
Label Location Outer Wrap
Paint X
Sticker X
Marker X
Packing Slip
Wired Tag
Crayon X
Scrap Type Palletized Coil Cuts
Label Location Scrap Surface
Paint X
Sticker X
Marker X
Packing Slip X
Wired Tag
Crayon X
Scrap Type Bundled Cut Coil
Label Location Consistant Face
Paint X
Sticker X
Marker X
Packing Slip X
Wired Tag
Crayon X
4” MAX
Banding through ID to prevent shifting
Page 10 of 16 TITLE: Scrap Quality Specification Revision 11
5.11 Ingot
a) Dimensions:
Width: Min = 40”, Max = 94” Length: Min = 120”, Max = 305” Thickness: Min = 18”, No Max
b) Weight Max = 60,000 lbs. with delivery to Oswego. c) Ingots longer than 200” or heavier than 40,000 lbs. require special notice
and a different appointment time (See Delivery Schedule, section 7.0). d) Ingots with excessively concave short sides will not be accepted because
they are unsafe for our grabs. e) Ingot must be marked “Remelt” or “Scrap,” along with the alloy, clearly
on the short sides. f) No cracks that make handling the ingot by forklift or 4-point-crane-grabs
unsafe, will be allowed.
5.12 Ingot Cuts
a) Max weight for ingot cuts at Berea & Greensboro is 6,000 lbs. Cuts
weighing more than 6,000 lbs. must have prior delivery approval from the
plant.
b) Oswego is able to take ingot cuts and full-size ingots of up to 60,000 lbs.
5.13 Self-Supporting Plate/Sheet/Blanks (Less than 2” deflection if
lifted in the middle) Tier 1 certified only c) Width = 40” to 90” (64” max if greater than 8,000 lbs.).
d) Length = 40” to 108” e) Max weight including pallet is 11,500 lbs. for Oswego and 6,000 lbs. for
Berea and Greensboro.
f) The maximum plate thickness for Berea and Greensboro is .5”. g) All pieces larger than 75” x 75” require special notice and a different
appointment time (See Delivery Schedule, section 7.0).
I ngot Grabs Unsafe Crack for Ingot Handling
Page 11 of 16 TITLE: Scrap Quality Specification Revision 11
h) Plate loaded on a flatbed or conastoga must be loaded so that it can be
side unloaded. Plate loaded in a van will be rear unloaded. i) Any plate loaded on a flatbed or conastoga must be tarped at all times.
In the event that the driver untarps early and the material gets wet, it will be rejected.
j) Plate/sheets should not be wrapped in plastic. k) Plate/sheets must be wrapped in fiber or steel bands.
5.14 Not Self-Supporting Plate/Sheet/Blanks (Tier 1 certified only)
a) Same dimensions and weight as Self-Supporting (see section 4.12).
b) This material is to be banded to other pieces of the same size, in 2 directions, such that no sheet can freely slide apart and be dangerous.
Sheet scrap is dangerous because its f lexible nature can a llow it to s lide
off the forks of the fork truck and cause damage or injury. c) Sheet scrap of the same alloy should be bundled together to a minimum
of 1,000 lbs. Maximum weight including pallet is 11,500 lbs. for Oswego
and 6,000 for Berea and Greensboro. d) Once banded together, the material is also to be banded to a pallet so
that the pallet can be removed without unfastening the banded material. e) Plate loaded on a flatbed or conastoga must be loaded so that it can be
side unloaded (forks holes turned to the side). Plate loaded in a van will
be rear unloaded. Therefore, the fork holes must be front-to-back. f) Any plate loaded on a flatbed or conastoga must be tarped at all times.
In the event that the driver untarps early and the material gets wet, it
will be rejected. g) Plate/sheets should not be wrapped in plastic. h) Plate/sheets must be wrapped in fiber or steel bands.
5.15 Shreds
a) Please see our shred scrap specifications.
Scrap Type Plate / Sheet
Label Location Scrap Surface
Paint X
Sticker X
Marker X
Packing Slip X
Wired Tag
Crayon X
Page 12 of 16 TITLE: Scrap Quality Specification Revision 11
5.16 Chopped Scrap
a) Packaging of plant scrap must be plant approved b) Chopped scrap piece size must be plant approved, because different
plants have different processes. c) Piece size (unless otherwise approved by the plant):
Maximum is 3.5” wide 8” long X 4mm guage
Minimum surface area is 1 square inch X 0.25 mm guage
Textured chopped scrap is preferred. Textured material reduces surface friction and improves the flow of chopped scrap.
5.17 International Coil Form (Tier 1 certified only)
These forms are for coils shipping rear-loaded, in a trailer with anchor points.
a) Eye Horizontal
5.17.a.1 Dimensions: Width 18” to 100”, ID Min = 6”. 5.17.a.2 Coils should be banded together, in twos or threes, to a bundle
weight of no greater than 11,500 lbs. when delivered to Oswego
and 6,000 lbs., when delivered to Berea or Greensboro. 5.17.a.3 Coils that cannot be bundled into pairs, due to weight, are to be
shipped per requirement 4.5. 5.17.a.4 Coils must be placed on slip mats, on pallets (see diagram,
below).
Page 13 of 16 TITLE: Scrap Quality Specification Revision 11
b) Eye Vertical
5.17.b.1 Coils should be banded together, to a bundle weight of no
greater than 11,500 lbs. when delivered to Oswego and 6,000
lbs. when delivered to Berea or Greensboro. 5.17.b.2 Coil(s) must be fastened to a pallet so they cannot move on the
pallet.
5.0 SCRAP DELIVERY & UNLOADING POLICY 5.1 Rear loaded trailers:
a) Rear loaded trailers are only allowed on trailers with firm, rigid sides (i.e. van
trailers).
b) Coils, or bundles of coils, must be less than 5,000 lbs. unless the trailer has
anchor points.
c) Scrap must be at least 6” from the top of the trailer and door opening so that
it can be removed with a fork truck.
5.2 Side loaded trailers: a) Due to the fact that most side loads are unloaded outside, any truck that is
side loaded may be rejected or forced to wait at the shipper’s expense due to
any weather conditions that pose a danger to unloading personnel or equipment.
b) Any load with a single piece greater than 11,500 lbs. must be side loaded for
Oswego only; for Berea and Greensboro 6,000 lbs. c) Flatbed trailers must be side loaded.
Page 14 of 16 TITLE: Scrap Quality Specification Revision 11
6.0 SECURED LOADS
6.1 All loads must be packaged and secured to meet the requirements specified by the
Department of Transportation, in the United States, and by the Ministry of
Transportation, in Canada.
6.2 All material must be secured to prevent shifting during transit. If the load shifts
and is unsafe or would require twice (or more) the amount of time than is allotted
to that load for unloading, the load will be rejected. Consistent demonstration of
poor loading practices will result in disqualification. Please consult the Buyer if
there are any questions about allotted unloading time.
7.0 DELIVERY SCHEDULE 7.1 In the interest of both parties, as well as the shipping companies involved,
efficient and safe delivery of material is critical for keeping shipping costs down.
As a result, ALL MATERIAL must have a delivery appointment. Novelis is not responsible for any costs that may be incurred because a load arrives before a
scheduled delivery appointment. Unloading hours are 24 hours/day, 7 days a
week except for holidays. Please work with your Recycling Coordinator for questions on the delivery calendar at a specific plant.
8.0 SCRAP RADIATION POLICY & IDENTIFICATION 8.1 Supplier warrants that none of the material purchased or delivered is , or contains
radioactive materials.
8.2 Supplier agrees to defend, indemnify and hold harmless Novelis and its subsidiaries and affiliates, and it’s directors, officers, employees, agents and
representatives (“Novelis Indemnitees”) from any and all claims, demands,
damages, liabilities, costs, expenses and fees (including reasonable attorney’s fees), arising out of, resulting from, or relating to, in whole or in part, a breach of
the foregoing warranty.
8.3 The supplier understands that it’s material will be tested before and after acceptance by Novelis, and, as such, Novelis shall have the right to revoke the
acceptance of the materials at any time. If radioactive material is discovered,
Novelis may, at its option and without prior notice or approval from the supplier, undertake to handle, dispose of and/or clean up the radioactive material. All
costs, fees and expenses associated with the handling, disposal and cleanup, and
the return of the shipment whether or not undertaken exclusively by Novelis, shall become the responsibility of the supplier, and the supplier shall release, defend,
indemnify and hold harmless Novelis Indemnitees from any and all claims,
demands, damages, liabilities, costs, expenses, fees and penalties arising out of, resulting from, or relating to, in whole or in part, said handling, disposal, and
cleanup. Supplier further agrees to waive any claims, rights and defenses which it
might otherwise have against Novelis Indemnitees arising out of, resulting from or relating to the handling, disposal of, and/or clean up of the radioactive material by
Novelis or its designees.
Page 15 of 16 TITLE: Scrap Quality Specification Revision 11
8.4 Each purchase order is contingent upon the supplier’s acceptance of these terms.
Supplier acknowledges that delivery of any material to Novelis shall be deemed
acceptance of these terms, and agrees that any terms and conditions contained in
a proposal, quotation, acknowledgement, acceptance, invoice or other document of supplier which are different from or in addition to these terms and conditions
shall not constitute a part of the purchase order and are hereby expressly
rejected, and that no employee of Novelis is authorized to or may waive or modify these terms.
9.0 SCRAP REJECTION POLICY
9.1 The Operator or Crew Leader determines if any part of the load is unacceptable for
any of the preceding reasons involving safety, quality of material, signed purchase order or delivery.
9.2 The Buyer will then notify supplier as to why a load has been rejected. The
supplier is responsible for all freight and reloading costs to ship the rejected load from Novelis. If available, photos will be sent to supplier for review.
9.3 Rejected material must be promptly removed. If the rejected material is not
removed within 5 business days, the rejected material will be sent collect to the vendor or location of the vendor’s choice. This purchase order shall remain open
subject to the original terms and conditions.
10.0 INSPECTION & SAMPLING
10.1 Each load of purchased scrap will be examined upon receipt for compliance with
the description of the material on the purchase order. The material will also be
sampled for chemical composition. The method and frequency of inspection and
sampling will be at Novelis’ discretion. A failed physical inspection or chemical
analysis may result in the load being rejected or downgraded. 10.2 If a scrap charge causes an off analysis furnace, the vendor who supplied the
material will be responsible for all charges related to the incident.
11.0 SHIPPING DOCUMENTATION:
The driver must provide the following core shipment information must appear on the Bill
of Lading and is required for all shipments:
a) SRA number (Shipping Request Authorization) b) Shipper name, city and state
c) Type of product (alloy) & form (Baled, densified, etc.)
d) Piece count
Page 16 of 16 TITLE: Scrap Quality Specification Revision 11
e) Indicate actual scale weight or an estimated weight, which must be marked
“estimated”
f) Dunnage
g) Ship date h) Certification: “This shipment is being transported for the purpose of recycling as
defined in the applicable tariffs containing such provisions”.
i) Duplicate bill of lading is required at the receiving location.
12.0 INSURANCE
12.1 Each vendor selling scrap to Novelis will have and maintain adequate minimum
insurance coverage including but not limited to, general and products liability
insurance coverage, protecting both Novelis and supplier from any and all claims
and liabilities for property damage, personal injury, death and economic damage,
that arise from the material and associated activities hereunder, endorsed as
required, at all times while conducting business with Novelis.
*** Specifications are subject to change without prior notice ***