Post on 10-Feb-2018
BMW Motorrad
K72_800_Titel.fm Seite 9 Montag, 24. September 2007 3:14 15
The Ultimate RidingMachine
Rider's ManualF 800GS
Motorcycle data/dealership details
Motorcycle data
Model
Vehicle identification number
Colour code
Date of first registration
Registration number
Dealership details
Person to contact in Service department
Ms/Mr
Phone number
Dealership address/phone number (com-pany stamp)
Details described or illustratedin this booklet may differ fromthe motorcycle's actual specifica-tion as purchased, the accessor-ies fitted or the national-marketspecification. No claims will beentertained as a result of suchdiscrepancies.Dimensions, weights, fuel con-sumption and performance dataare quoted to the customary tol-erances.The right to modify designs,equipment and accessories isreserved.Errors and omissions excepted.
© 2008 BMW MotorradNot to be reproduced eitherwholly or in part without writtenpermission from BMW Motorrad,After Sales.Printed in Germany.
Important data for refuelling
FuelRecommended fuel grade 95 ROZ/RON, Super unleadedwith regular unleaded (RON 91)OE 91 ROZ/RON, Regular unleaded
(fuel grade, usable with power-and consumption-related restric-tions)
Usable fuel capacity approx. 16 l
Reserve fuel ≥4 l
Tyre pressureTyre pressure, front 2.2 bar, one-up, at tyre temperat-
ure: 20 °C2.5 bar, two-up and/or with lug-gage, at tyre temperature: 20 °C
Tyre pressure, rear 2.5 bar, one-up, at tyre temperat-ure: 20 °C2.9 bar, two-up and/or with lug-gage, at tyre temperature: 20 °C
BMW recommends
Order No. 01 41 7 714 40102.2008, 2nd edition
*01417714401**01417714401**01417714401*
Welcome to BMW
We congratulate you on yourchoice of a motorcycle fromBMW and welcome you to thecommunity of BMW riders.Familiarise yourself with your newmotorcycle so that you can ride itsafely and confidently in all trafficsituations.Please read this Rider's Manualcarefully before starting to useyour new BMW motorcycle. Itcontains important information onhow to operate the controls andhow to make the best possibleuse of all your BMW's technicalfeatures.In addition, it contains informationon maintenance and care to helpyou maintain your motorcycle'sreliability and safety, as well as itsvalue.If you have questions concerningyour motorcycle, your authorised
BMW Motorrad dealer will gladlyprovide advice and assistance.
We hope that you will enjoy rid-ing your BMW and that all yourjourneys will be pleasant andsafe.
BMW Motorrad.
Table of Contents
You can also consult the index atthe end of this Rider's Manual ifyou want to find a particular topicor item of information.1 General instructions . . . . . 5Overview . . . . . . . . . . . . . . . . . . . . . . 6Abbreviations and symbols . . . . 6Equipment . . . . . . . . . . . . . . . . . . . . 7Technical data . . . . . . . . . . . . . . . . 7Currency . . . . . . . . . . . . . . . . . . . . . . 7
2 General views . . . . . . . . . . . . . 9General view, left side . . . . . . . . 11General view, right side . . . . . . 13Underneath the seat . . . . . . . . . 14Underneath the trim pan-el . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Handlebar fitting, left . . . . . . . . . 16Handlebar fitting, right . . . . . . . . 17Instrument cluster . . . . . . . . . . . . 18Headlight . . . . . . . . . . . . . . . . . . . . . 19
3 Status indicators . . . . . . . 21Standard statusindicators . . . . . . . . . . . . . . . . . . . . . 22Status indicators with on-board computerOE . . . . . . . . . . . 23Standard warnings . . . . . . . . . . . 24Warnings issued by the on-board computerOE . . . . . . . . . . . 29ABS warningsOE . . . . . . . . . . . . . 30Anti-theft alarmwarningsOE . . . . . . . . . . . . . . . . . . . 32
4 Operation . . . . . . . . . . . . . . . . 35Ignition switch and steeringlock . . . . . . . . . . . . . . . . . . . . . . . . . . 36Electronic immobiliser(EWS) . . . . . . . . . . . . . . . . . . . . . . . . 37Clock . . . . . . . . . . . . . . . . . . . . . . . . . 38Odometer and tripmeters . . . . 38On-board computerOE . . . . . . . 39Lights . . . . . . . . . . . . . . . . . . . . . . . . 45Turn indicators . . . . . . . . . . . . . . . 46Hazard warning flashers . . . . . . 47Emergency off switch (killswitch) . . . . . . . . . . . . . . . . . . . . . . . 48
Grip heatingOE . . . . . . . . . . . . . . . 48BMW Motorrad ABSOE . . . . . . 49Clutch . . . . . . . . . . . . . . . . . . . . . . . . 50Brakes . . . . . . . . . . . . . . . . . . . . . . . 50Mirrors . . . . . . . . . . . . . . . . . . . . . . . 51Spring preload . . . . . . . . . . . . . . . 51Damping . . . . . . . . . . . . . . . . . . . . . 52Tyres . . . . . . . . . . . . . . . . . . . . . . . . . 53Headlight . . . . . . . . . . . . . . . . . . . . . 54Seat . . . . . . . . . . . . . . . . . . . . . . . . . . 55Helmet holder . . . . . . . . . . . . . . . . 56
5 Riding . . . . . . . . . . . . . . . . . . . . 57Safety instructions . . . . . . . . . . . 58Checklist . . . . . . . . . . . . . . . . . . . . . 60Starting . . . . . . . . . . . . . . . . . . . . . . . 60Running in . . . . . . . . . . . . . . . . . . . 62Brakes . . . . . . . . . . . . . . . . . . . . . . . 63Parking your motorcycle . . . . . 65Refuelling . . . . . . . . . . . . . . . . . . . . 66Securing motorcycle fortransportation . . . . . . . . . . . . . . . . 67
6 Engineering details . . . . . 69Brake system with BMW Mo-torrad ABSOE . . . . . . . . . . . . . . . . 70
7 Accessories . . . . . . . . . . . . . 73General instructions . . . . . . . . . . 74Power socket . . . . . . . . . . . . . . . . 74Luggage . . . . . . . . . . . . . . . . . . . . . 75CaseOA . . . . . . . . . . . . . . . . . . . . . . 77TopcaseOA . . . . . . . . . . . . . . . . . . . 80
8 Maintenance . . . . . . . . . . . . 85General instructions . . . . . . . . . . 86Toolkit . . . . . . . . . . . . . . . . . . . . . . . . 86Engine oil . . . . . . . . . . . . . . . . . . . . 87Brake system . . . . . . . . . . . . . . . . 88Brake pads . . . . . . . . . . . . . . . . . . . 89Brake fluid . . . . . . . . . . . . . . . . . . . . 90Coolant . . . . . . . . . . . . . . . . . . . . . . . 91Clutch . . . . . . . . . . . . . . . . . . . . . . . . 92Tyres . . . . . . . . . . . . . . . . . . . . . . . . . 92Rims . . . . . . . . . . . . . . . . . . . . . . . . . 93Chain . . . . . . . . . . . . . . . . . . . . . . . . . 93Wheels . . . . . . . . . . . . . . . . . . . . . . . 95Front-wheel stand . . . . . . . . . . 102Bulbs . . . . . . . . . . . . . . . . . . . . . . . 103Air filter . . . . . . . . . . . . . . . . . . . . . 110
Jump starting . . . . . . . . . . . . . . 111Battery . . . . . . . . . . . . . . . . . . . . . 112
9 Care . . . . . . . . . . . . . . . . . . . . . 117Care products . . . . . . . . . . . . . . 118Washing motorcycle . . . . . . . . 118Cleaning easily damagedcomponents . . . . . . . . . . . . . . . . 118Paint care . . . . . . . . . . . . . . . . . . 119Protective wax coating . . . . . 120Laying up motorcycle . . . . . . 120Restoring motorcycle touse . . . . . . . . . . . . . . . . . . . . . . . . . 120
10 Technical data . . . . . . . 121Troubleshooting chart . . . . . . 122Threaded fasteners . . . . . . . . 123Engine . . . . . . . . . . . . . . . . . . . . . 125Fuel . . . . . . . . . . . . . . . . . . . . . . . . 126Engine oil . . . . . . . . . . . . . . . . . . 126Clutch . . . . . . . . . . . . . . . . . . . . . . 127Transmission . . . . . . . . . . . . . . . 127Rear-wheel drive . . . . . . . . . . . 128Running gear . . . . . . . . . . . . . . . 128Brakes . . . . . . . . . . . . . . . . . . . . . 129Wheels and tyres . . . . . . . . . . . 129Electrics . . . . . . . . . . . . . . . . . . . . 131
Frame . . . . . . . . . . . . . . . . . . . . . . 133Dimensions . . . . . . . . . . . . . . . . 133Weights . . . . . . . . . . . . . . . . . . . . 134Riding specifications . . . . . . . 134
11 Service . . . . . . . . . . . . . . . . 135BMW Motorrad service . . . . . 136BMW Motorrad servicequality . . . . . . . . . . . . . . . . . . . . . . 136BMW Motorrad ServiceCard: on-the-spot break-down assistance . . . . . . . . . . . 136BMW Motorrad service net-work . . . . . . . . . . . . . . . . . . . . . . . . 137Maintenance work . . . . . . . . . . 137Confirmation of mainten-ance work . . . . . . . . . . . . . . . . . . 138Confirmation of service . . . . . 143
General instructions
General instructions
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Abbreviations and symbols . . . . . . . . . . . 6
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Technical data . . . . . . . . . . . . . . . . . . . . . . . . 7
Currency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
15
z Gen
eral
inst
ruct
ion
s
OverviewChapter 2 of this Rider's Manu-al will provide you with an initialoverview of your motorcycle. Allmaintenance and repair work onthe motorcycle is documented inChapter 11. This record of themaintenance work you have hadperformed on your motorcycle isa precondition for generous treat-ment of goodwill claims.When the time comes to sellyour BMW, please rememberto hand over this Rider's Manu-al; it is an important part of themotorcycle.
Abbreviations andsymbols
Indicates warnings that youmust comply with for reas-
ons of your safety and the safetyof others, and to protect yourmotorcycle against damage.
Specific instructions onhow to operate, control, ad-
just or look after items of equip-ment on the motorcycle.
Indicates the end of anitem of information.
Instruction.
Result of an activity.
Reference to a page withmore detailed informa-tion.
Indicates the end of apassage relating to spe-cific accessories or itemsof equipment.
Tightening torque.
Item of technical data.
OE Optional extraThe motorcycles are as-sembled complete withall the BMW optional ex-tras originally ordered.
OA Optional accessoryYou can obtain option-al accessories throughyour authorised BMWMotorrad dealer; optionalaccessories have to beretrofitted to the motor-cycle.
EWS Electronic immobiliser(Elektronische Wegfahr-sicherung).
DWA Anti-theft alarm (Diebs-tahlwarnanlage)
ABS Anti-lock brake system
16
z Gen
eral
inst
ruct
ion
s
EquipmentWhen you ordered your BMWmotorcycle, you chose variousitems of custom equipment. ThisRider's Manual describes option-al extras (OE) offered by BMWand selected optional accessor-ies (OA). This explains why themanual may also contain de-scriptions of equipment whichyou have not ordered. Pleasenote, too, that your motorcyclemight not be exactly as illus-trated in this manual on accountof country-specific differences.If your BMW was supplied withequipment not described inthis Rider's Manual, you willfind these features described inseparate manuals.
Technical dataAll dimensions, weights andpower ratings stated in theRider's Manual are quoted to thestandards and comply with thetolerance requirements of theDeutsche Institut für Normunge.V. Versions for individualcountries may differ.
CurrencyThe high safety and qualitystandards of BMW motorcyclesare maintained by constantdevelopment work on designs,equipment and accessories.Because of this, your motorcyclemay differ from the informationsupplied in the Rider's Manual.Nor can BMW Motorrad entirelyrule out errors and omissions.We hope you will appreciate thatno claims can be entertained onthe basis of the data, illustrationsor descriptions in this manual.
17
z Gen
eral
inst
ruct
ion
s
General views
General views
General view, left side . . . . . . . . . . . . . . . . 11
General view, right side . . . . . . . . . . . . . . 13
Underneath the seat . . . . . . . . . . . . . . . . . 14
Underneath the trim panel . . . . . . . . . . . 15
Handlebar fitting, left . . . . . . . . . . . . . . . . . 16
Handlebar fitting, right . . . . . . . . . . . . . . . 17
Instrument cluster . . . . . . . . . . . . . . . . . . . 18
Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
29
z Gen
eral
vie
ws
General view, left side1 Power socket ( 74)2 Seat lock ( 55)3 Engine-oil filler neck and oil
dipstick ( 87)
211
z Gen
eral
vie
ws
General view, right side1 Fuel filler neck ( 66)2 Brake-fluid reservoir, rear
( 91)3 Vehicle Identification Num-
ber (VIN) (on steering-headbearing), Type plate (onsteering-head bearing)
4 Brake-fluid reservoir, front( 90)
5 Coolant level indicator (be-hind side panel) ( 91),Coolant filler neck (behindside panel) ( 92)
6 Adjuster for spring preload,rear ( 51)
7 Adjuster for damping char-acteristic, rear suspension( 52)
213
z Gen
eral
vie
ws
Underneath the seat1 Location of first-aid kit (OA)2 Toolkit3 Payload table4 Table of tyre pressures5 Helmet holder ( 56)6 Rider's Manual7 Tool for adjusting spring
preload ( 51)
214
z Gen
eral
vie
ws
Handlebar fitting, left1 Operating the on-board
computerOE ( 39)2 Operating the ABSOE
( 49)3 Horn4 Flashing turn indicators,
left ( 46), Hazard warn-ing flashers ( 47)
5 High-beam headlight andheadlight flasher ( 45)
216
z Gen
eral
vie
ws
Handlebar fitting, right1 Emergency off switch (kill
switch) ( 48)2 Starter button ( 60)3 Grip heatingOE ( 48)4 Flashing turn indicators,
right ( 46), Hazard warn-ing flashers ( 47)
5 Cancel button, flashing turnindicators ( 47), Pushbut-ton, cancel hazard warningflashers ( 47)
217
z Gen
eral
vie
ws
Instrument cluster1 Telltale lights ( 22)2 Speedometer3 Operation of the clock
( 38), Operation of thestopwatchOE ( 42)
4 Multifunction display( 22)
5 Operating the odometer( 38)
6 Telltale light, anti-theft alarm(OE), Sensor for instrumentlighting, Warning light forengine rpmOE ( 44)
7 Rev. counter
The instrument-clusterlighting has automatic day
and night switchover.
218
z Gen
eral
vie
ws
Status indicators
Status indicators
Standard status indicators . . . . . . . . . . . 22
Status indicators with on-board com-puterOE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Standard warnings . . . . . . . . . . . . . . . . . . . 24
Warnings issued by the on-boardcomputerOE . . . . . . . . . . . . . . . . . . . . . . . . . 29
ABS warningsOE . . . . . . . . . . . . . . . . . . . . . 30
Anti-theft alarm warningsOE . . . . . . . . . 32
321
z Sta
tus
ind
icat
ors
Standard statusindicatorsMultifunction display
1 Clock ( 38)2 Odometer and tripmeters
( 38)
Telltale lights
1 High-beam headlight2 Flashing turn indicators, left3 Idle4 Flashing turn indicators,
right
Service-due indicator
If the next service is due in lessthan one month, the date for thenext service is shown briefly afterthe Pre-Ride Check completes.The month is shown as a two-digit number and the year as afour-digit number, with a colonas separator, so in this examplethe next service is due in March2007.
322
z Sta
tus
ind
icat
ors
If the motorcycle covers long dis-tances in the course of the year,under certain circumstances itmight be necessary to have itserviced at a date in advanceof the forecast due date. If thecountdown distance to the odo-meter reading at which a servicewill be due is less than 1000 km,the distance is counted down insteps of 100 km and is shownbriefly after the Pre-Ride Checkcompletes.
If service is overdue, the duedate or the odometer reading atwhich service was due is accom-
panied by the 'General' warninglight showing yellow. The word"Service" remains permanentlyvisible.
If the service-due indicatorappears more than a month
in advance of the actual due dateor if the word "Service" does notshow permanently even thougha service is overdue, the datestored in memory in the instru-ment panel is incorrect and mustbe set. This situation can occur ifthe battery was disconnected fora prolonged period of time.If you want to have the date setconsult a specialist workshop,preferably an authorised BMWMotorrad dealer.
Status indicators withon-board computer OE
Multifunction display
1 Status-indicator panel ofthe on-board computerOE( 39)
2 Gear indicator ( 23)3 Coolant temperature
( 24)4 Fuel capacity ( 24)
Gear indicatorThe gear engaged or Nfor neutral appears on the
display.
323
z Sta
tus
ind
icat
ors
If no gear is engaged, the'neutral' telltale light also
lights up.
Coolant temperatureThe horizontal bars abovethe temperature symbol
indicate the coolant temperature.
Fuel capacityThe horizontal bars abovethe fuel-pump symbol in-
dicate the remaining quantity offuel. The top bar is larger thanthe others and the quantity offuel it represents is correspond-ingly larger.When the fuel in the tank istopped up the gauge brieflyshows the original level, beforethe reading is updated.
Standard warningsMode of presentation
Warnings are indicated by thewarning lights 1 or by the 'Gen-eral' warning light 2 showing incombination with a text warningor a warning symbol in the mul-tifunction display. The 'General'warning light shows red or yel-low, depending on the urgency ofthe warning.
Warning symbols 1 and 2 canappear on the multifunction dis-play. Text warnings such as 3,for example, appear in the odo-meter panel and are accompan-ied by warning-triangle symbol 4.
If two or more warnings occur atthe same time, all the appropriatewarning lights and warning sym-bols appear. You can call up textwarnings to alternate with theodometer readings ( 38). Thestatus of the 'General' warninglight matches the most urgentwarning.
324
z Sta
tus
ind
icat
ors
Warnings, overviewTelltale lights Status indicators Meaning
Lights up yellow Appears on the dis-play
Electronic immobiliser active ( 27)
EWS appears onthe display.
Lights up Fuel down to reserve ( 27)
Lights up red Flashes Coolant temperature too high ( 27)
Lights up yellow Appears on the dis-play
Engine in emergency-operation mode( 28)
Flashes Insufficient engine oil pressure ( 28)
Lights up yellow Appears on the dis-play
Bulb defective ( 28)
LAMP appears onthe display.
326
z Sta
tus
ind
icat
ors
Electronic immobiliseractive
General warning light showsyellow.
Warning-triangle symbolappears on the display.
EWS appears on the display.Possible cause:The key being used is not au-thorised for starting, or commu-nication between key and engineelectronics is disrupted.Remove all other vehicle keysfrom the same ring as the igni-tion key.Use the reserve key.Have the defective key re-placed, preferably by an au-thorised BMW Motorrad dealer.
Fuel down to reserveWarning light for fuel downto reserve shows.
Lack of fuel can result inthe engine misfiring and
cutting out unexpectedly. Mis-firing can damage the catalyticconverter; a hazardous situationcan result if the engine cuts outunexpectedly.Do not run the fuel tank dry.
Possible cause:The fuel tank contains no morethan the reserve quantity of fuel.
Reserve fuel
≥4 lRefuel ( 66)
Coolant temperature toohigh
General warning light showsred.
The temperature symbolflashes.
Continuing to ride when theengine is overheated could
result in engine damage.You must comply with the in-structions below.
Possible cause:If the coolant level is too low.Check the coolant level ( 91)
If the coolant level is too low:Top up the coolant ( 92)
Possible cause:The coolant temperature is toohigh.If possible, ride in the part-loadrange to cool down the engine.In traffic jams, switch off theengine, but leave the ignitionswitched on so that the radiat-or fan continues to operate.If the coolant temperature isfrequently too high, have thefault rectified as soon as pos-sible by a specialist workshop,
327
z Sta
tus
ind
icat
ors
preferably an authorised BMWMotorrad dealer.
Engine in emergency-operation mode
General warning light showsyellow.
Engine symbol appears onthe display.
The engine is running inemergency operating mode.
Engine power might be reducedand this can cause hazardoussituations, particularly if you at-tempt to overtake other roadusers.Engine power level might belower than normal: adapt yourstyle of riding accordingly.
Possible cause:The engine control unit has dia-gnosed a fault. In exceptionalcases, the engine stops and re-fuses to start. Otherwise, the en-
gine runs in emergency operatingmode.You can continue to ride, butbear in mind that the usual en-gine power might not be avail-able.Have the fault rectified asquickly as possible by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Insufficient engine oilpressure
Warning light for engine-oilpressure flashes.
The oil pressure in the lube-oilsystem is too low. Stop immedi-ately and switch off the engine.
The insufficient oil pres-sure warning does not fulfil
the function of an oil gauge. Theonly way of checking whetherthe oil level is correct is to checkwith the oil dipstick.
Possible cause:The engine-oil level is too low.Check the engine oil level( 87)
If the oil level is too low:Top up the engine oil ( 88)
Possible cause:The engine-oil pressure is insuffi-cient.
Riding when engine-oilpressure is low can result
in engine damage.Do not continue your journey.
Have the fault rectified asquickly as possible by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Bulb defectiveGeneral warning light showsyellow.
328
z Sta
tus
ind
icat
ors
Warning-triangle symbolappears on the display.
LAMP appears on the display.
A defective bulb placesyour safety at risk because
it is easier for other users tooversee the motorcycle.Replace defective bulbs assoon as possible; always carry acomplete set of spare bulbs ifpossible.
Possible cause:Low-beam headlight, parkinglight, rear-light, brake-light orturn-indicator bulb defective.Visually inspect to ascertainwhich bulb is defective.Replacing low-beam headlightbulb ( 104)Replacing high-beam headlightbulb ( 104)Replacing parking-light bulb( 106)
Replace the brake light andrear light bulb ( 108)Replacing turn indicator bulbs,front and rear ( 107)
Warnings issued by theon-board computer OE
The ambient-temperature read-ing flashes.
Possible cause:The air temperature measuredat the motorcycle is lower than3 °C.
The ice warning does notmean that there is no risk
of black ice forming at measuredtemperatures above 3 °C.Always take extra care and thinkwell ahead when temperaturesare low; remember that thedanger of black ice is particularlyhigh on bridges and where theroad is in the shade.
Ride carefully and think wellahead.
329
z Sta
tus
ind
icat
ors
ABS warnings OE
Mode of presentation
ABS warnings are indicated byABS warning light 1.The way in which the ABS warn-ing light indicates status can dif-fer in some countries.
Possible national variant.
The detailed descriptions relatingto BMW Motorrad ABS start onpage ( 70), and you will findan overview listing the possiblewarnings on the next page.
330
z Sta
tus
ind
icat
ors
Warnings, overviewTelltale lights Status indicators Meaning
Flashes Self-diagnosis not completed ( 32)
Lights up ABS deactivated ( 32)
Lights up ABS fault ( 32)
331
z Sta
tus
ind
icat
ors
Self-diagnosis notcompleted
ABS warning light flashes.
Possible cause:The ABS function is notavailable, because self-diagnosis did not complete. Themotorcycle has to move forwarda few metres for the wheelsensors to be tested.Pull away slowly. Bear in mindthat the ABS function is notavailable until self-diagnosis hascompleted.
ABS deactivatedABS warning light shows.
Possible cause:The rider has switched off theABS system.
with BMW Motorrad ABSOE
Activate the ABS function( 49)
ABS faultABS warning light shows.
Possible cause:The ABS control unit has detec-ted a fault. The ABS function isnot available.You can continue to ride. Bearin mind that the ABS functionis not available. Bear in mindthe more detailed informationon situations that can lead toan ABS fault ( 71).Have the fault rectified asquickly as possible by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Anti-theft alarmwarnings OE
General warning light showsyellow.
The text warning dWA appears,accompanied by a warning-tri-angle symbol to indicate that thisis a warning.
This error message appearsonly briefly after the pre-
ride check completes.
332
z Sta
tus
ind
icat
ors
Possible cause:The integral battery in the anti-theft alarm has lost its entire ori-ginal capacity. There is no assur-ance that the anti-theft alarm willbe operational if the motorcycle'sbattery is disconnected.Seek the advice of a specialistworkshop, preferably an author-ised BMW Motorrad dealer.
333
z Sta
tus
ind
icat
ors
Operation
Operation
Ignition switch and steering lock . . . . . 36
Electronic immobiliser (EWS) . . . . . . . . 37
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Odometer and tripmeters . . . . . . . . . . . . 38
On-board computerOE . . . . . . . . . . . . . . . 39
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Turn indicators . . . . . . . . . . . . . . . . . . . . . . . 46
Hazard warning flashers . . . . . . . . . . . . . . 47
Emergency off switch (kill switch) . . . . 48
Grip heatingOE . . . . . . . . . . . . . . . . . . . . . . . 48
BMW Motorrad ABSOE . . . . . . . . . . . . . . 49
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Spring preload . . . . . . . . . . . . . . . . . . . . . . . 51
Damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Helmet holder . . . . . . . . . . . . . . . . . . . . . . . 56
435
z Op
erat
ion
Ignition switch andsteering lockKeysYou receive one master key andone spare key. Please consultthe information on the electronicimmobiliser (EWS) if a key is lostor mislaid ( 37).Ignition switch and steering lock,tank filler cap lock and seat lockare all operated with the samekey.
with caseOA
with topcaseOA
If you wish you can arrange tohave the cases and the top-case fitted with locks that canbe opened with this key as well.Consult a specialist workshop,preferably an authorised BMWMotorrad dealer.
Switching on ignition
Turn the key to position 1.Side light and all function cir-cuits switched on.Engine can be started.Pre-ride check is performed.( 61)
with BMW Motorrad ABSOE
Turn the key to position 1.ABS self-diagnosis isperformed in addition tothe checks outlined above.( 62)
Switching off ignition
Turn the key to position 2.Lights switched off.Handlebars not locked.Key can be removed.Electrically powered accessor-ies remain operational for a lim-ited period of time.The battery can be rechargedvia the on-board socket.
436
z Op
erat
ion
Locking handlebars
Turn the handlebars all the wayto the leftTurn the key to position 3,while moving the handlebarsslightly.Ignition, lights and all functioncircuits switched off.Handlebars locked.Key can be removed.
Electronic immobiliser(EWS)Protection against theftThe electronic immobiliser EWShelps protect your BMW mo-torcycle from theft, and this en-hanced security is at your dis-posal without any need for you toset parameters or activate addi-tional systems. The engine of amotorcycle fitted with this elec-tronic immobiliser can be startedonly with the keys that belong tothe vehicle. You can also haveyour authorised BMW Motor-rad dealer bar individual keys, forexample if a particular key goesmissing. The engine cannot bestarted with a key that has beenbarred.
In-key electronicsThe motorcycle's electronicsexchange certain continuouslychanging signals with the elec-tronics in the key; these signalsare specific to your motorcycleand they are transmitted via thering aerial in the ignition lock.The ignition is not enabled forstarting until the key has beenrecognised as "authorised" foryour motorcycle.
A spare key attached tothe same ring as the ig-
nition key used to start the en-gine could "irritate" the electron-ics, in which case the enablingsignal for starting is not issued.The EWS warning appears in themultifunction display.Always keep the spare key sep-arately from the ignition key.
437
z Op
erat
ion
Replacement and extrakeysYou can obtain replacement/extrakeys only through an authorisedBMW Motorrad dealer. The keysare part of an integrated secur-ity system, so the dealer is un-der an obligation to check thelegitimacy of all applications forreplacement/extra keys. If youwant to have a lost key barred,you have to bring with you allthe other keys that belong tothe motorcycle. A key that hasbeen barred can subsequently becleared and reactivated for use.
ClockSetting clock
Attempting to set the clockwhile riding the motorcycle
can lead to accidents.Set the clock only when the mo-torcycle is stationary.
Switch on the ignition.
Press and hold down button 1.Hours reading 2 flashes.Press button 1.The hours reading incrementsby one each time you pressthe button.Press and hold down button 1.Minutes reading 3 flashes.Press button 1.The minutes reading incre-ments by one each time youpress the button.
Either press and hold downbutton 1 or wait without press-ing any button.The clock is now set and thetime appears on the display.
Odometer andtripmetersSelecting readingsSwitch on the ignition.with on-board computerOE
If necessary, use button 1 toswitch from the stopwatch tothe odometer.
438
z Op
erat
ion
Press button 2.
The display starts with the cur-rent value and each time the but-ton is pressed it moves one stepthrough the following sequence:
Total distance covered
Tripmeter 1 (Trip I)Tripmeter 2 (Trip II)Tyre pressures (OE)Warnings, if applicable
Resetting tripmeterSwitch on the ignition.Select the desired tripmeter.
Press and hold down button 2.The tripmeter is reset to zero.
On-board computer OE
Selecting readingsSwitch on the ignition.
Press button 1.
439
z Op
erat
ion
Ambient temperatureAverage speedAverage consumptionCurrent consumptionRange
Ambient temperature
When the motorcycle is at astandstill the heat of the enginecan falsify the ambient-temper-ature reading. If the effect of theengine's heat becomes excess-ive, -- temporarily appears onthe display.
If ambient temperature drops be-low 3 °C the temperature dis-play flashes to draw your atten-tion to the risk of black ice form-ing. The display automaticallyswitches from any other modeto the temperature reading whenthe temperature drops below thisthreshold for the first time.
Average speed
Average speed is calculated onthe basis of the time elapsedsince the last reset. Timesduring which the engine wasstopped are excluded from thecalculation.
Resetting average speedSwitch on the ignition.Select average speed.
Press and hold down button 1.Average speed is reset to zero.
440
z Op
erat
ion
Average consumption
Average consumption is calcu-lated by dividing the distancecovered since the last reset bythe corresponding amount of fuelused.
Resetting averageconsumptionSwitch on the ignition.Select average consumption.
Press and hold down button 1.Average consumption is resetto zero.
Current consumption
Current consumption is shown.
441
z Op
erat
ion
Range
The range readout indicates howfar you can ride with the fuel re-maining in the tank. The figureis calculated from the level offuel in the tank and a postulatedaverage consumption, stored inmemory, that is not always thesame as the average that can beviewed on the display.The system cannot tell exactlyhow much fuel is on board whenthe tank is completely full. Underthese circumstances the displayshows a minimum-range figureaccompanied by a > symbol. Amore accurate figure for range is
shown as soon as the fuel levelcan be measured exactly.When refuelling after running onreserve, make sure that you topup the tank to a level above re-serve, as otherwise the sensorwill not be able to register thenew level. If the sensor cannotregister the new level neither thefuel-level reading nor the rangereadout can be updated.
The calculated range is onlyan approximate reading.
Consequently, BMW Motorradrecommends that you should nottry to use the full range beforerefuelling.
Stopwatch
You can switch from the odo-meter reading to a stopwatch.The readout is in hours, minutes,seconds and tenths of a second,with dots as separators.If you want to use the stopwatchas a lap timer, you can operateit by means of the INFO buttonon the handlebar fitting insteadof using button 2. If you set thecontrols so that the stopwatch isoperated by means of the INFObutton, you must use button 2 tooperate the on-board computer.The stopwatch continues to timein the background if you switch
442
z Op
erat
ion
back temporarily to the odometerreading. Similarly, the stopwatchcontinues timing if you temporar-ily switch off the ignition.
Operating stopwatch
If necessary, use button 1 toswitch from the odometer tothe stopwatch.
Press button 2 while the stop-watch is stopped.The stopwatch begins timingin tenths of a second from thetime originally shown.Press button 2 while the stop-watch is running.The stopwatch shows thestopped time.Press and hold down button 2.The stopwatch is reset andshows 0.00.00.0.
Using stopwatch as Lap-Timer
Press button 1 and button 2at the same time and holdthem down until the readingchanges.FLASH (redline warning) ap-pears, along with ON or OFF.Press button 2.LAP (Lap-Timer) appears,along with ON or OFF.Repeatedly press button 1 untilthe reading shows the modeyou want.
443
z Op
erat
ion
ON: Stopwatch operated bymeans of the INFO button onthe handlebar fitting.OFF: Stopwatch operated bymeans of button 2 in the in-strument cluster.To confirm the setting, pressbutton 1 and button 2 atthe same time and holdthem down until the readingchanges.The settings are accepted andthe display returns to its mostrecent reading.The most recent setting is re-tained if you do not confirm thenew settings.
Redline warning
The redline warning indicatesthat engine revolutions havereached the rev. counter's redsegment. The anti-theft alarmtelltale light 1 flashes red to in-dicate that the engine is red-lining.The signal remains active un-til you shift up or reduce enginespeed. You can activate or deac-tivate the redline warning.
Activating redline warning
Press button 1 and button 2at the same time and holdthem down until the readingchanges.FLASH (redline warning) ap-pears, along with ON or OFF.Repeatedly press button 1 untilthe reading shows the modeyou want.ON: Redline warning activated.OFF: Redline warning deactiv-ated.To confirm the setting, pressbutton 1 and button 2 atthe same time and hold
444
z Op
erat
ion
them down until the readingchanges.The settings are accepted andthe display returns to its mostrecent reading.The most recent setting is re-tained if you do not confirm thenew settings.
LightsSide lightThe side lights switch on auto-matically when the ignition isswitched on.
The side lights placea strain on the battery.
Do not switch the ignitionon for longer than absolutelynecessary.
Low-beam headlightThe low-beam headlight switcheson automatically when you startthe engine.
When the engine is notrunning you can switch on
the lights by switching on the ig-nition and either switching on thehigh-beam headlight or operatingthe headlight flasher.
High-beam headlight
Press the top section of full-beam headlight switch 1.High-beam headlight switchedon.Move full-beam headlightswitch 1 to the centre position.High-beam headlight switchedoff.
Press the bottom section offull-beam headlight switch 1.The high-beam headlight isswitched on until you releasethe button (headlight flasher).
Switching on parkinglightsSwitch off the ignition.
Immediately after switchingoff the ignition, press and holddown button 1 for the left turnindicators.Parking light switches on.
445
z Op
erat
ion
Switching off parkinglightsSwitch the ignition on and thenoff again.Parking lights switched off.
Turn indicatorsSwitching on left flashingturn indicatorsSwitch on the ignition.
The turn indicators are can-celled automatically after
you have ridden for approxim-ately 10 seconds, or covered adistance of about 200 m.
Press button 1 for the left-hand turn indicators.Left-hand turn indicatorsswitched on.Telltale light for left-hand turnindicators flashes.
Switching on rightflashing turn indicatorsSwitch on the ignition.
The turn indicators are can-celled automatically after
you have ridden for approxim-ately 10 seconds, or covered adistance of about 200 m.
Press button 2 for the right-hand turn indicators.Right-hand turn indicatorsswitched on.Telltale light for right-hand turnindicators flashes.
446
z Op
erat
ion
Cancelling turn indicators
Press cancel button 3.Flashing turn indicatorsswitched off.Turn indicator telltale lights areoff.
Hazard warningflashersSwitching on hazardwarning flashersSwitch on the ignition.
The hazard warning flash-ers place a strain on the
battery. Do not use the hazard
warning flashers for longer thanabsolutely necessary.
If you press a turn-indicat-or button with the ignition
switched on, the turn-indicatorfunction is activated instead ofthe hazard warning flashers, andremains active until you releasethe button. The hazard warningflashers recommence flashing assoon as the button is released.
Simultaneously press button 1for left turn indicators and but-ton 2 for right turn indicators.
The hazard warning flashersare switched on.Left/right turn indicator telltalelights flash.Switch off the ignition.The hazard warning flasherscontinue to operate.Left and right turn indicatortelltale lights are off.
Switching off hazardwarning flashers
Press cancel button 3.Hazard warning flashersswitched off.
447
z Op
erat
ion
Emergency off switch(kill switch)
1 Emergency off switch (killswitch)
Operating the kill switchwhen riding can cause
the rear wheel to lock and thuscause a fall.Do not operate the kill switchwhen riding.
The emergency off switch is akill switch for switching off theengine quickly and easily.
a Normal operating position(run)
b Engine switched off.
You cannot start the engineunless the kill switch is in
the run position.
Grip heatingOE
1 Grip-heating switch
The handlebar grips have two-stage heating. Grip heating canbe activated only when the en-gine is running.
The increase in power con-sumption caused by the
grip heating can drain the bat-tery if you are riding at low en-gine speeds. If the charge levelis low, grip heating is switchedoff to ensure the battery's start-ing capability.
448
z Op
erat
ion
2 Heating off.3 50 % heat output (one dot
visible)4 100 % heat output (three
dots visible)
BMW Motorrad ABSOE
Deactivating ABS functionSwitch on the ignition, or bringthe motorcycle to a stop.
Press and hold down ABS but-ton 1.
ABS warning light starts toshow.
Release the ABS button withinfive seconds.
ABS warning light remainsON.
The ABS function is deactiv-ated.
Activating ABS function
Press and hold down ABS but-ton 1.
ABS warning light goes out;if self-diagnosis has not
completed it starts flashing.Release the ABS button withinfive seconds.
The ABS warning light re-mains off or continues to
flash.
The ABS function is activated.Instead of pressing the ABSbutton, you have the option ofswitching the ignition off andthen on again.
449
z Op
erat
ion
If you switch the ignition offthen on again and the ABS
light comes back on, there is afault in the ABS.
ClutchAdjusting clutch lever
Attempting to adjust theclutch lever while riding the
motorcycle can lead to accidents.Do not attempt to adjust theclutch lever unless the motor-cycle is at a standstill.
Turn adjusting screw 1 clock-wise.
The adjusting screw is easi-er to turn if you push the
clutch lever forward.
Span between handlebar gripand clutch lever increases.Turn adjusting screw 1counter-clockwise.Span between handlebar gripand clutch lever decreases.
BrakesAdjusting handbrake lever
Changing the position ofthe brake-fluid reservoir can
allow air to penetrate the brakesystem.Do not twist the handlebar fittingor the handlebars.
Attempting to adjust thebrake lever while riding the
motorcycle can lead to accidents.Do not attempt to adjust thebrake lever unless the motorcycleis at a standstill.
Turn adjusting screw 1 clock-wise.
The adjusting screw is easi-er to turn if you push the
handbrake lever forward.
Span between handlebar gripand handbrake lever increases.Turn adjusting screw 1counter-clockwise.Span between handlebar gripand handlebar lever decreases.
450
z Op
erat
ion
MirrorsAdjusting mirrors
Turn the mirror to the correctposition.
Adjusting mirror arm
Push protective cap 1 up overthe threaded fastener on themirror arm.Slacken nut 2.Turn the mirror arm to the ap-propriate position.Tighten the nut to the spe-cified tightening torque, whileholding the mirror arm to en-sure that it does not move outof position.
Mirror to clamping ele-ment
20 Nm
Push the protective cap overthe threaded fastener.
Spring preloadSettingIt is essential to set spring pre-load of the rear suspension tosuit the load carried by the mo-torcycle. Increase spring preloadwhen the motorcycle is heavilyloaded and reduce spring preloadaccordingly when the motorcycleis lightly loaded.
Adjusting spring preloadfor rear wheelRemove the seat ( 55)
451
z Op
erat
ion
Remove on-board toolkit 1.
Your motorcycle's hand-ling will suffer if you do not
match the spring-preload anddamping-characteristic settings.
Adjust the damping characteristicto suit spring preload.
If you want to increase springpreload, use the tool from theon-board toolkit to turn knob 2clockwise.If you want to reduce springpreload, use the tool from theon-board toolkit to turn knob 2counter-clockwise.
Basic setting of springpreload, rear
Turn the adjusting screwcounter-clockwise as far as itwill go (Full load of fuel, withrider 85 kg)
Stow on-board toolkit 1.Install the seat ( 55)
DampingDampingDamping must be adapted to suitthe surface on which the motor-cycle is ridden and to suit springpreload.An uneven surface requiressofter damping than a smoothsurface.An increase in spring preloadrequires firmer damping, a re-duction in spring preload re-quires softer damping.
452
z Op
erat
ion
Adjusting damping forrear wheel
You adjust the damping char-acteristic by turning adjustingscrew 1.
If you want to increase damp-ing, turn adjusting screw 1clockwise.If you want to reduce damping,turn adjusting screw 1 counter-clockwise.
Basic setting of rear-sus-pension damping charac-
teristic
Turn adjusting screw as faras it will go clockwise, thenback it off 1 1/2 turns. (Fullload of fuel, with rider 85 kg)
TyresChecking tyre pressureMake sure the ground is leveland firm and place the motor-cycle on its stand.
Incorrect tyre pressures im-pair the motorcycle's hand-
ling characteristics and increasethe rate of tyre wear.Always check that the tyre pres-sures are correct.
At high road speeds, tyrevalves have a tendency to
open as a result of centrifugalforce.Fit valve caps with rubber sealsand screw them on firmly to pre-vent sudden deflation.
Check tyre pressures againstthe data below.
453
z Op
erat
ion
Tyre pressure, front
2.2 bar (one-up, at tyre tem-perature 20 °C)
2.5 bar (two-up and/or withluggage, at tyre temperature20 °C)
Tyre pressure, rear
2.5 bar (one-up, at tyre tem-perature 20 °C)
2.9 bar (two-up and/or withluggage, at tyre temperature20 °C)
If tyre pressure is too low:Correct tyre pressure.
HeadlightAdjusting headlight fordriving on left/driving onrightIf the motorcycle is ridden in acountry where the opposite ruleof the road applies, its asymmet-ric low-beam headlight will tendto dazzle oncoming traffic.Have the headlight set accord-ingly by a specialist workshop,preferably an authorised BMWMotorrad dealer.
Headlight beam throw andspring preloadHeadlight beam throw is gener-ally kept constant when springpreload is adjusted to suit load.Spring preload adjustment mightnot suffice only if the motorcycleis very heavily loaded. Underthese circumstances, headlightbeam throw has to be adjusted
to suit the weight carried by themotorcycle.
Consult a specialist work-shop, preferably an au-
thorised BMW Motorrad deal-er, if you are unsure whetherthe headlight basic setting iscorrect.
Adjusting headlight beamthrow
Slacken screws 1 on left andright.Adjust beam throw by tiltingthe headlight slightly about itshorizontal axis.
454
z Op
erat
ion
Tighten screws 1 on left andright.
Beam-throw basic setting
Slacken screws 1 on left andright.Tilt the headlight slightlyabout its horizontal axis untilarrowhead 2 is pointing towardmarker 3.Tighten screws 1 on left andright.
SeatRemoving seatMake sure the ground is leveland firm and place the motor-cycle on its stand.
Use the ignition key to turnseat lock 1 counter-clockwiseand hold it in this position.
Lift seat 2 at the front and re-lease the key.Remove the seat and set itdown on the rubber buffers.
Installing seat
Engage the seat in holders 3.
455
z Op
erat
ion
Firmly press down on the seatat the front.The seat engages with an aud-ible click.
Helmet holderRemove the seat ( 55)
Pass the wire rope available asan optional accessory throughthe helmet and slip both eyesof the wire rope over a helmetholder 1.
The helmet catch canscratch the panelling.
Make sure the lock is out of theway when you hook the helmetinto position.
If it is attached on the leftside of the motorcycle,
there is a possibility of the hel-met being damaged by the hotend silencer.If possible, attach the helmeton the right-hand side of themotorcycle.
Work both helmet and wirerope to the rear.Install the seat ( 55)
456
z Op
erat
ion
Riding
Riding
Safety instructions . . . . . . . . . . . . . . . . . . . 58
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Running in . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Parking your motorcycle . . . . . . . . . . . . . 65
Refuelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Securing motorcycle for transporta-tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
557
z Rid
ing
Safety instructionsRider's equipmentDo not ride without the correctclothing. Always wear:HelmetMotorcycling jacket andtrousersGlovesBoots
This applies even to short jour-neys, and to every season of theyear. Your authorised BMW Mo-torrad dealer will be glad to ad-vise you on the correct clothingfor every purpose.
SpeedIf you ride at high speed, alwaysbear in mind that various bound-ary conditions can adversely af-fect the handling of your motor-cycle:
Settings of the spring-strut andshock-absorber systemImbalanced loadLoose clothingInsufficient tyre pressurePoor tyre treadEtc.
Correct loadingOverloading and imbal-anced loads can adversely
affect the motorcycle's handling.Do not exceed the permissiblegross weight and be sure tocomply with the instructions onloading.
Alcohol and drugsEven small amounts ofalcohol or drugs will ad-
versely affect your perceptionand your ability to assess situ-ations and make decisions, andslow down your reflexes. Med-ication can exacerbate these ef-fects.
Do not ride your motorcycle afterconsuming alcohol, drugs and/ormedication.
Risk of poisoningExhaust fumes contain carbonmonoxide, which is colourlessand odourless but highly toxic.
Inhaling the exhaust fumestherefore represents a
health hazard and can evencause loss of consciousness withfatal consequences.Do not inhale exhaust fumes.Do not run the engine in an en-closed space.
High voltageTouching live parts of theignition system with the
engine running can cause electricshock.Do not touch parts of the igni-tion system when the engine isrunning.
558
z Rid
ing
Catalytic converterIf misfiring causes unburned fuelto enter the catalytic converter,there is a danger of overheatingand damage.For this reason, observe the fol-lowing points:Do not run the fuel tank dry.Do not attempt to start or runthe engine with a spark-plugcap disconnected.Stop the engine immediately ifit misfires.Use only unleaded fuel.Comply with all specified main-tenance intervals.
Unburned fuel will destroythe catalytic converter.
Note the points listed for protec-tion of the catalytic converter.
Risk of fireTemperatures at the exhaust arehigh.
Flammable materials (e.g.hay, leaves, grass, clothing
and luggage, etc.) could igniteif allowed to come into contactwith the hot exhaust pipe.Do not permit flammable materi-als to come into contact with thehot exhaust system.
Cooling would beinadequate if the engine
were allowed to idle for a lengthyperiod with the motorcycle ata standstill: overheating wouldresult. In extreme cases, themotorcycle could catch fire.Do not allow the engine to idleunnecessarily. Ride away imme-diately after starting the engine.
Tampering with thecontrol unit of theelectronic engine-management system
Tampering with the enginecontrol unit can damage
the motorcycle and cause acci-dents.Do not tamper with the enginecontrol unit.
Tampering with the enginecontrol unit can result in
mechanical loads that the mo-torcycle's components are notdesigned to withstand. Damagecaused in this way is not coveredby the warranty.Do not tamper with the enginecontrol unit.
559
z Rid
ing
ChecklistUse the following checklist tocheck important functions, set-tings and wear limits before youride off.BrakesBrake-fluid levels, front and rearClutchDamping-characteristic settingand spring preloadTyre-tread depth and tyrepressuresCases correctly installed andluggage secured
At regular intervals:Engine oil level (every refuellingstop)Brake-pad wear (every thirdrefuelling stop)
StartingSide standYou cannot start the motorcyclewith the side stand extended anda gear engaged. The engine willswitch itself off if you start it withthe gearbox in neutral and thenengage a gear before retractingthe side stand.
GearboxYou can start the engine whenthe gearbox is in neutral or if youpull the clutch with a gear en-gaged. Do not pull the clutch un-til after you have switched on theignition, as otherwise the enginewill refuse to start. When thegearbox is in neutral, the greenneutral telltale light is on and thegear indicator in the multifunctiondisplay shows N.
Starting engine
Kill switch in run position a.
Gearbox lubrication is en-sured only when the engine
is running. Inadequate lubrica-tion can result in damage to thegearbox.Do not allow the motorcycle toroll for a lengthy period of time orpush it a long distance with theengine switched off.
Switch on the ignition.Pre-ride check is performed.( 61)
560
z Rid
ing
with BMW Motorrad ABSOE
Switch on the ignition.Pre-ride check is performed.( 61)ABS self-diagnosis isperformed. ( 62)
Press starter button 1.
If ambient temperatures arevery low, you might find it
necessary to open the throttleslightly when starting the engine.At ambient temperatures below0 °C, disengage the clutch afterswitching on the ignition.
The start attempt is auto-matically interrupted if bat-
tery voltage is too low. Rechargethe battery before you start theengine, or use jump leads and adonor battery to start.
The engine starts.If the engine refuses to start,consult the troubleshootingchart in the section entitled"Technical data". ( 122)
Pre-ride checkThe instrument cluster runs atest of the instruments and thetelltale and warning lights whenthe ignition is switched on. ThisPre-Ride-Check, as it is known,is aborted as soon you start theengine.
Phase 1The rev. counter and speedo-meter needles both swing to thelimit values on their scales.
At the same time, the followingwarning lights and telltale lightsare switched on in succession:Telltale light for high-beamheadlight and left turn indicatortelltale lightGeneral warning light, showingyellow, and neutral telltale lightWarning light for fuel down toreserve and right turn indicatortelltale lightWarning light for oil pressure
with BMW Motorrad ABSOE
ABS warning light
Phase 2General warning lightchanges from yellow to red.
Phase 3The rev. counter and speedo-meter needles both swing backto rest. At the same time, all thewarning lights and telltale lightsswitched on in the initial phase
561
z Rid
ing
are switched off in reverse se-quence.
If a needle did not move or if awarning light or telltale light didnot show as specified above:
Some malfunctions cannotbe indicated if one of the
warning lights fails to show.Make sure that all the warningand telltale lights come on in thepre-ride check.
Have the fault rectified asquickly as possible by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
ABS self-diagnosisOE
BMW Motorrad ABS performsself-diagnosis to ensure its op-erability. Self-diagnosis is per-formed automatically when youswitch on the ignition. The mo-torcycle has to move forward a
few metres for the wheel sensorsto be tested.
Phase 1Test of the diagnosis-compat-ible system components withthe motorcycle at a standstill.
ABS warning light flashes.
Possible national variant ofthe ABS warning light.
Phase 2Test of the wheel sensors asthe motorcycle pulls away fromrest.
ABS warning light flashes.
Possible national variant ofthe ABS warning light.
ABS self-diagnosiscompletedThe ABS warning light goesout.
If an indicator showing an ABSfault appears when ABS self-dia-gnosis completes:You can continue to ride. Bearin mind that the ABS functionis not available.Have the fault rectified asquickly as possible by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Running inThe first 1000 kmWhile running in the motor-cycle, vary the throttle openingand engine-speed range fre-quently.Try to do most of your rid-ing during this initial period ontwisting, fairly hilly roads, avoid-ing high-speed main roads andhighways if possible.
562
z Rid
ing
Exceeding the specified en-gine speeds while running
in will lead to increased enginewear.Keep to the specified enginespeeds for running in.
Do not exceed the rpm limitsrecommended for running in.
Running-in speed
<5000 min-1
No full-load acceleration.Avoid low engine speeds at fullload.Do not omit the first inspectionafter 500 - 1200 km.
Brake padsNew brake pads must "beddown" and therefore do notachieve their optimum frictionlevels during the first 500 km.You can compensate for thisinitial reduction in braking
efficiency by exerting greaterpressure on the levers.
New brake pads can ex-tend stopping distance by a
significant margin.Apply the brakes in good time.
TyresNew tyres have a smooth sur-face. This must be roughened byriding in a restrained manner atvarious heel angles until the tyresare run in. This running in pro-cedure is essential if the tyres areto achieve maximum grip.
Tyres do not have their fullgrip when new and there
is a risk of accidents at extremeangles of heel.Avoid extreme angles of heel.
BrakesHow can stoppingdistance be minimised?Each time the brakes are applied,a load distribution shift takesplace with the load shifting for-ward from the rear to the frontwheel. The sharper the motor-cycle decelerates, the more loadis shifted to the front wheel. Thehigher the wheel load, the morebraking force can be transmittedwithout the wheel locking.To optimise stopping distance,apply the front brakes rapidly andkeep on increasing the force youapply to the brake lever. Thismakes the best possible use ofthe dynamic increase in load atthe front wheel. Remember topull the clutch at the same time.In the "panic braking situations"that are trained so frequentlybraking force is applied as rap-idly as possible and with the
563
z Rid
ing
rider's full force applied to thebrake levers; under these circum-stances the dynamic shift in loaddistribution cannot keep pacewith the increase in decelerationand the tyres cannot transmitthe full braking force to the sur-face of the road. The front wheellocks and the imminent risk of afall increases.
with BMW Motorrad ABSOE
ABS has to intervene to keepthe front wheel from locking; thisincreases stopping distance.
Descending mountainpasses
There is a danger of thebrakes fading if you use
only the rear brakes when des-cending mountain passes. Underextreme conditions, the brakescould overheat and suffer severedamage.Use both front and rear brakes,
and make use of the engine'sbraking effect as well.
Wet brakesAfter the motorcycle hasbeen washed, ridden
through water or ridden inthe rain, the brake discs andpads might be wet and thebrakes might not take effectimmediately.Apply the brakes in good timeuntil the brakes have dried out.
Salt on brakesThe brakes may fail to takeeffect immediately if the
motorcycle was ridden on salt-covered roads and the brakeswere not applied for some time.Apply the brakes in good timeuntil the salt layer on the brakediscs and brake pads has beenremoved.
Oil or grease on brakesOil and grease on the brakediscs and pads considerably
diminish braking efficiency.Especially after repair and main-tenance work, make sure that thebrake discs and brake pads arefree of oil and grease.
Dirt or mud on brakesWhen riding on loose sur-faces or muddy roads, the
brakes may fail to take effectimmediately because of dirt ormoisture on the discs or brakepads.Apply the brakes in good timeuntil the brakes have beencleaned.
The brake pads will wearmore rapidly if you ride fre-
quently on unsurfaced tracks orpoor roads.Check the thickness of the brake
564
z Rid
ing
pads more frequently and replacethe brake pads in good time.
Parking yourmotorcyclePlacing motorcycle onside stand
If the ground is soft or un-even, there is no guaran-
tee that the motorcycle will restfirmly on the stand.Always check that the groundunder the stand is level andfirm.
Switch off the engine.Pull the handbrake lever.Hold the motorcycle uprightand balanced.Use your left foot to extend theside stand fully.
The side stand is designedto support only the weight
of the motorcycle.Do not lean or sit on the
motorcycle with the side standextended.
Slowly lean the motorcycle tothe side until its weight is takenby the stand and dismount tothe left.
If the motorcycle is on theside stand, the surface of
the ground will determine wheth-er it is better to turn the handle-bars to the left or right. However,the motorcycle is more stable ona level surface with the handle-bars turned to the left than withthe handlebars turned to theright.On level ground, always turn thehandlebars to the left to set thesteering lock.
Turn the handlebars to full leftor right lock.Check that the motorcycle isstanding firmly.
On a gradient, the motor-cycle should always face
uphill; select 1st gear.
Lock the steering lock.
Removing motorcyclefrom side standUnlock the steering lock.From the left, grip the handle-bars with both hands.Pull the handbrake lever.Swing your right leg over theseat and lift the motorcycle tothe upright position.Hold the motorcycle uprightand balanced.
An extended side stand cancatch on the ground when
the motorcycle is moving andlead to a fall.Retract the side stand beforemoving the motorcycle.
Sit on the motorcycle and useyour left foot to retract the sidestand.
565
z Rid
ing
Placing motorcycle oncentre standOE
If the ground is soft or un-even, there is no guaran-
tee that the motorcycle will restfirmly on the stand.Always check that the groundunder the stand is level andfirm.
Switch off the engine.Dismount and keep your lefthand on the left handlebar grip.With your right hand, grip therear grab handle or the rearframe.Use your right foot on the pinof the centre stand to pressthe stand down until its curvedfeet touch the ground.Place your full body weight onthe centre stand and at thesame time pull the motorcycleto the rear.
Excessive movementscould cause the centre
stand to retract, and themotorcycle would topple inconsequence.Do not lean or sit on the mo-torcycle with the centre standextended.
Check that the motorcycle isstanding firmly.Lock the steering lock.
Removing motorcyclefrom centre standOE
Unlock the steering lock.Place your left hand on the lefthandlebar grip.With your right hand, grip therear grab handle or the rearframe.Push the motorcycle forwardoff the centre stand.Check that the centre standhas fully retracted.
RefuellingFuel is highly flammable. Anaked flame close to the
fuel tank can cause a fire or ex-plosion.Do not smoke. Never bring anaked flame near the fuel tank.
Fuel expands when hot.Fuel escaping from an
overfilled tank could make its wayonto the rear tyre. This couldcause a fall.Do not fill the tank past the bot-tom edge of the filler neck.
Fuel attacks plastics, whichbecome dull or unsightly.
Wipe off plastic parts immediatelyif they come into contact withfuel.
Leaded fuel will destroy thecatalytic converter.
Use only unleaded fuel.
566
z Rid
ing
Make sure the ground is leveland firm and place the motor-cycle on its side stand.
The volume of the tank canbe utilised to the full only
when the motorcycle is proppedon its side stand.
Open the protective cap.Open the fuel tank cap withthe ignition key by turning itcounter-clockwise.
Refuel with fuel of the gradestated below; do not fill thetank past the bottom edge ofthe filler neck.
Recommended fuelgrade
95 ROZ/RON (Super un-leaded)
with regular unleaded (RON91)OE
91 ROZ/RON (Regularunleaded (fuel grade,usable with power- andconsumption-relatedrestrictions))
Usable fuel capacity
approx. 16 l
Reserve fuel
≥4 lPress the fuel tank cap downfirmly to close.Remove the key and close theprotective cap.
Securing motorcyclefor transportationMake sure that all componentsthat might come into contactwith straps used to secure themotorcycle are adequately pro-tected against scratching. Useadhesive tape or soft cloths, forexample, for this purpose.
567
z Rid
ing
The motorcycle can toppleand fall on its side.
Make sure that the motorcyclecannot topple sideways.
Push the motorcycle onto thetransportation flat and hold it inposition: do not place it on theside stand or centre stand.
Risk of damaging compon-ents.
Take care not to trapcomponents such as brake linesor wires.
At the front, secure the strapsto the bottom fork bridge onboth sides and tighten thestraps.
At the rear, secure the strapsto the rear frame on both sidesand tighten the straps.Tighten all the straps uniformly;the motorcycle's suspensionshould be compressed astightly as possible front andrear.
568
z Rid
ing
Engineering details
Engineering details
Brake system with BMW MotorradABSOE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
669
z En
gin
eeri
ng
det
ails
Brake system withBMW Motorrad ABS OE
How does ABS work?The amount of braking force thatcan be transferred to the roaddepends on factors hat includethe coefficient of friction of theroad surface. Loose stones, iceand snow or a wet road all havemuch lower coefficients of fric-tion than a clean, dry asphalt sur-face. The lower the coefficientof friction, the longer the brakingdistance.If the rider increases brakingpressure to the extent that brak-ing force exceeds the maxim-um transferrable limit, the wheelsstart to lock and the motorcycleloses its directional stability; a fallis imminent. Before this situationcan occur, ABS intervenes andadapts braking pressure to themaximum transferrable brakingforce, so the wheels continue
to turn and directional stabilityis maintained irrespective of thecondition of the road surface.
What are the effects ofsurface irregularities?Humps and surface irregularit-ies can cause the wheels to losecontact temporarily with the roadsurface; if this happens the brak-ing force that can be transmit-ted to the road can drop to zero.If the brakes are applied underthese circumstances the ABShas to reduce braking force toensure that directional stabilityis maintained when the wheelsregain contact with the road sur-face. At this instant the BMWMotorrad ABS must assume anextremely low coefficient of fric-tion, so that the wheels will con-tinue to rotate under all imagin-able circumstances, because thisis the precondition for ensuringdirectional stability. As soon as
is registers the actual circum-stances, the system reacts in-stantly and adjusts braking forceaccordingly to achieve optimumbraking.
Rear wheel liftUnder very severe and suddendeceleration, however, under cer-tain circumstances it is possiblethat the BMW Motorrad ABS willbe unable to prevent the rearwheel from lifting clear of theground.If this happens the out-come can be a highsiding situ-ation in which the motorcycle canflip over.
Severe braking can causethe rear wheel to lift off the
ground.When you brake, bear in mindthat ABS control cannot be reliedon in all circumstances to preventthe rear wheel from lifting clear ofthe ground.
670
z En
gin
eeri
ng
det
ails
What is the designbaseline for BMWMotorrad ABS?Within the limits imposed byphysics, BMW Motorrad ABS en-sures directional stability on anysurface. The system is not op-timised for special requirementsthat apply under extreme com-petitive situations off-road or onthe track.
Special situationsThe speeds of the front and rearwheels are compared as onemeans of detecting a wheel'sincipient tendency to lock. If thesystem registers implausible val-ues for a lengthy period the ABSfunction is deactivated for safetyreasons and an ABS fault mes-sage is issued. Self-diagnos-is has to complete before faultmessages can be issued.In addition to problems with theBMW Motorrad ABS, exceptional
riding conditions can lead to afault message being issued.Exceptional ridingconditions:Riding for a lengthy period withthe front wheel lifted off theground (wheelie).Rear wheel rotating with themotorcycle held stationary byapplying the front brake (burn-out).Heating up with the motorcycleon the centre stand or an auxil-iary stand, engine idling or witha gear engaged.Rear wheel locked for a lengthyperiod, for example while des-cending off-road.
If a fault message is issued onaccount of exceptional ridingconditions as outlined above, youcan reactivate the ABS functionby switching the ignition off andon again.
What significancedevolves on regularmaintenance?
Invariably, a technical sys-tem cannot perform beyond
the abilities dictated by its levelof maintenance.In order to ensure that the BMWMotorrad ABS is always main-tained in optimum condition, itis essential for you to complystrictly with the specified inspec-tion intervals.
Reserves for safetyThe potentially shorter brakingdistances which BMW MotorradABS permits must not be usedas an excuse for careless riding.ABS is primarily a means of en-suring a safety margin in genuineemergencies.Take care when cornering. Whenyou apply the brakes on a corner,the motorcycle's weight and
671
z En
gin
eeri
ng
det
ails
momentum take over and evenBMW Motorrad ABS is unable tocounteract their effects.
672
z En
gin
eeri
ng
det
ails
Accessories
Accessories
General instructions. . . . . . . . . . . . . . . . . . 74
Power socket . . . . . . . . . . . . . . . . . . . . . . . . 74
Luggage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
CaseOA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
TopcaseOA . . . . . . . . . . . . . . . . . . . . . . . . . . 80
773
z Acc
esso
ries
General instructionsBMW Motorrad recommendsthe use of parts and accessoriesfor your motorcycle that are ap-proved by BMW for this purpose.Genuine BMW parts and ac-cessories and other productswhich BMW has approved canbe obtained from your authorisedBMW Motorrad dealer, togetherwith expert advice on their install-ation and use.These parts and products havebeen tested by BMW for safety,function and suitability. BMWaccepts product liability for them.Conversely, BMW is unable toaccept any liability whatsoeverfor parts and accessories which ithas not approved.
BMW Motorrad cannotassess each non-BMW
product to determine wheth-er it can be used on or in con-nection with BMW motorcycles
without constituting a safety haz-ard. Country-specific official au-thorisation does not suffice asassurance. Tests conducted bythese instances cannot makeprovision for all operating con-ditions experienced by BMW mo-torcycles and, consequently, theyare not sufficient in some circum-stances.Use only parts and accessor-ies approved by BMW for yourmotorcycle.
Whenever you are planningmodifications, comply with allthe legal requirements. Makesure that the motorcycle doesnot infringe national road-vehicleconstruction and use regulations.
Power socketRatings
The supply to socket 1 is cut offautomatically if battery voltageis low or the load exceeds themaximum rating.
Operating electricalaccessoriesYou can start using electrical ac-cessories only when the ignitionis switched on. The accessoryremains operational if the ignitionis subsequently switched off. Inorder to ensure that the drain onthe on-board power supply sys-
774
z Acc
esso
ries
tem is minimised, the supply tothe power socket is cut off ap-proximately 15 minutes after theignition is switched off, and it isalso temporarily interrupted dur-ing the start procedure.
Cable routingThe cables from the power sock-et to the auxiliary device must berouted in such a way that they:Do not impede the riderDo not restrict or obstruct thesteering angle and handlingcharacteristicsCannot be trapped
Incorrectly routed cablescan impede the rider.
Route the cables as describedabove.
LuggageCorrect loading
Overloading and imbal-anced loads can adversely
affect the motorcycle's handling.Do not exceed the permissiblegross weight and be sure tocomply with the instructions onloading.
Set spring preload, dampingcharacteristic and tyre pres-sures to suit total weight.with caseOA
Ensure that the case volumeson the left and right are equal.Make sure that the weight isuniformly distributed betweenright and left.Pack heavy items at the bot-tom of the cases and towardthe inboard side.Note the maximum permissiblepayload of the cases and the
speed limit for riding with caseson the motorcycle.
Payload of cases
max 8 kg
Maximum permissiblespeed for riding with
cases fitted to the motorcycle
max 160 km/h
with topcaseOA
Note the maximum permiss-ible payload of the topcase andthe speed limit for riding with atopcase on the motorcycle.
Payload of topcase
max 5 kg
775
z Acc
esso
ries
Maximum permissiblespeed for riding with top-
case fitted to the motorcycle
max 160 km/h
with tank rucksackOA
Note the maximum permissiblepayload of the tank rucksackand the speed limit for ridingwith a tank rucksack on themotorcycle.
Payload of tank rucksack
max 5 kg
Maximum permissiblespeed for riding with the
tank rucksack fitted to the mo-torcycle
max 130 km/h
with rear softbagOA
Note the maximum permissiblepayload of the rear softbag and
the speed limit for riding with arear softbag on the motorcycle.
Payload of rear softbag
max 1.5 kg
Maximum permissiblespeed for riding with the
rear softbag fitted to the mo-torcycle
max 130 km/h
Lashing luggage
Loop the luggage straps overthe bar between the motor-cycle and stops 1.
776
z Acc
esso
ries
Position luggage strap 2 asshown here with a stuffbag asexample.Check that the luggage is se-cure.
Case OA
Opening cases
Turn key 1 in the case lock toright angles with the forwarddirection of travel.Hold down latch 2 and pull upcarrying handle 3.
Press the ribbed part of rockerswitch 4.Hold the rocker switch downand open the lid of the case.
777
z Acc
esso
ries
Closing cases
Turn the lock with the key untilit is at right angles to the for-ward direction of travel.Close case lid 1.The lid engages with an aud-ible click.
Closing the carry handlewhile the case lock is in
line with the forward direction oftravel can result in damage to thelocking tongue.Make sure that the case lock isat right angles to the forward dir-ection of travel when you closethe carry handle.
Push carry handle 2 down.The handle engages with anaudible click.Turn the key in the case lockin line with the forward direc-tion of travel and remove thekey from the lock.
Adjusting case volume
Open the case.Remove all its contents fromthe case.To adjust the volume of thecase, engage pivot lever 1 atthe top or bottom limit position,as applicable.
Pivot lever at top limit position:minimum volume.Pivot lever at bottom limit posi-tion: maximum volume.
Removing cases
Turn key 1 in the case lock toright angles with the forwarddirection of travel.Hold down latch 2 and pull upcarrying handle 3.
778
z Acc
esso
ries
Pull red release lever 4 up.Latching flap 5 pops up.Fully open latching flap 5.Take a grip of the carry handleand ease the case clear ofthe mushroom head and thecurved tubular section.
Installing case
Turn key 1 in the case lock toright angles with the forwarddirection of travel.Hold down latch 2 and pull upcarrying handle 3.
Pull red release lever 4 up.Latching flap 5 pops up.Fully open latching flap 5.
Engage anchorage 6 on curvedtubular section 7.
779
z Acc
esso
ries
Tilt the case up and set it onmushroom head 8, until mush-room head 8 is at the rear endof anchorage 9.
Then push latching flap 5down while pivoting red releaselever 4 down.The latching flap engages.Make sure that the case isnow latched in position on themushroom head.Push the carry handle downuntil closed.The handle engages with anaudible click.
Turn the key in the case lockin line with the forward direc-tion of travel and remove thekey from the lock.
TopcaseOA
Opening topcase
Turn key 1 in the topcase lockuntil it is at right angles to theroad surface.Hold down latch 2 and pull outcarry handle 3.
Press the ribbed part of rockerswitch 4.Hold the rocker down andopen the lid of the topcase.
780
z Acc
esso
ries
Closing topcase
Turn the key in the topcaselock until it is at right angles tothe road surface.Close topcase lid 1.The lid engages with an aud-ible click.
Closing the carry handlewhile the topcase lock is
vertical can result in damage tothe locking tongue.Make sure that the topcase lockis horizontal when you close thecarry handle.
Push carry handle 2 up.
The handle engages with anaudible click.Turn the key in the topcaselock until it is parallel with theroad surface and remove thekey.
Adjusting topcase volume
Open the topcase.Remove all its contents fromthe topcase.To adjust the volume of thetopcase, engage pivot lever 1at the front or rear limit posi-tion, as applicable.
Pivot lever at rear limit position(toward carry handle): minimumvolume.Pivot lever at front limit position(toward bottom of topcase):maximum volume.
Removing topcase
Turn key 1 in the topcase lockuntil it is at right angles to theroad surface.Hold down latch 2 and pull outcarry handle 3.
781
z Acc
esso
ries
Pull red lever 4.Latching flap 5 is unlocked.Fully open latching flap 5 withyour hand.Take a firm grip of the handleand remove the topcase.
Installing topcase
Turn key 1 in the topcase lockuntil it is at right angles to theroad surface.Hold down latch 2 and pull outcarry handle 3.
Pull red lever 4.Latching flap 5 is unlocked.Fully open latching flap 5 withyour hand.
782
z Acc
esso
ries
Engage the topcase in frontholders 6 of the topcase carrierplate.
Push the rear of the topcaseonto the topcase carrier plateand engage latching flap 5.
Push red lever 4 in.Latching flap 5 is secured.Check that the topcase is se-cure.Close the carry handle and lockthe topcase.
783
z Acc
esso
ries
Maintenance
Maintenance
General instructions. . . . . . . . . . . . . . . . . . 86
Toolkit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Brake system . . . . . . . . . . . . . . . . . . . . . . . . 88
Brake pads . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Rims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Front-wheel stand . . . . . . . . . . . . . . . . . 102
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Jump starting . . . . . . . . . . . . . . . . . . . . . . 111
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
885
z Mai
nte
nan
ce
General instructionsThe "Maintenance" chapter de-scribes straightforward proced-ures for checking and replacingcertain wear parts.Special tightening torques are lis-ted as applicable. The tighteningtorques for the threaded fasten-ers on your motorcycle are listedin the section entitled "Technicaldata".You will find information on moreextensive maintenance and re-pair work in the Repair Manualon DVD/CD-ROM (RepROM) foryour motorcycle, which is avail-able from your authorised BMWMotorrad dealer.
Some of the work calls for spe-cial tools and a thorough know-ledge of motorcycles. If youare in doubt consult a specialistworkshop, preferably your author-ised BMW Motorrad dealer.
ToolkitToolkit
1 Screwdriver handle2 Reversible screwdriver blade
With star-head and plain-tipends
3 Open-ended spannerWidth across flats 17
4 Torx wrench, T405 Reversible screwdriver blade
With star-head and TorxT25
On-board toolkit servicekit OA
1 Extending tool holderholds all tools by means ofadapters, and for removingthe spark plug
2 1/4" bitsBits of various sizes
3 3/8" adapter for socket-head screws, w/f 22for removing the quick-re-lease axle from the frontwheel
4 Electric torch
886
z Mai
nte
nan
ce
5 SocketOpen-ended spanners ofvarious sizes
6 AdapterTo accommodate the 1/4" bits and the 9x12 mmand the 3/8" universal-jointadapter
Engine oilChecking engine oil level
The engine can seize if theoil level is low, and this can
lead to accidents.Always make sure that the oillevel is correct.
The oil level varies with thetemperature of the oil. The
higher the temperature, the high-er the level of oil in the sump.Checking the oil level with theengine cold or after no more thana short ride will lead to misinter-pretation; this in turn, means that
the engine will be operated withthe incorrect quantity of oil.In order to ensure that the en-gine oil level is read correctly,check the oil level only after alengthy trip.
Wipe the area around the oilfiller neck clean.Allow the engine to idle untilthe fan starts up, then allow itto idle one minute longer.Switch off the ignition.Make sure the engine is at op-erating temperature and holdthe motorcycle upright.with centre standOE
Check that the engine is at op-erating temperature, make surethe ground is level and firmand place the motorcycle on itscentre stand.
Remove oil dipstick 1 by turn-ing it counter-clockwise.
Use a dry cloth to wipe gaugelength 2 clean
887
z Mai
nte
nan
ce
Seat the oil dipstick on the oilfiller neck, but do not engagethe threads.Remove the oil dipstick andcheck the oil level.
Engine oil level
Engine oil, 10W-40
0.4 l (Difference betweenMIN and MAX marks on theoil dipstick)
If the oil level is below the MINmark:Top up the engine oil ( 88)
If the oil level is above the MAXmark:Have the oil level corrected bya specialist workshop, prefer-ably an authorised BMW Mo-torrad dealer.
Topping up engine oilCheck the engine oil level( 87)
Pour engine oil in through fillerneck 1 until it reaches the spe-cified level.Install the oil dipstick.
Brake systemDependability of the brakesystemA fully functional brake system isa basic requirement for the roadsafety of your motorcycle.
Do not ride the motorcycle if youhave any doubts about the de-pendability of the brake system.Under these circumstances havethe brake system checked by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Incorrect working practicesendanger the reliability of
the brakes.Have all work on the brake sys-tem performed by a specialistworkshop, preferably an author-ised BMW Motorrad dealer.
Checking operation ofbrakesPull the handbrake lever.The pressure point must beclearly perceptible.Press the footbrake lever.The pressure point must beclearly perceptible.
888
z Mai
nte
nan
ce
If pressure points are not clearlyperceptible:Have the brakes checked by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Brake padsChecking brake-padthickness, front brakesMake sure the ground is leveland firm and place the motor-cycle on its stand.
Visually inspect the left andright brake pads to ascertain
their thickness. Viewing direc-tion: Between wheel and forktube toward brake caliper 1.
Brake-pad wear limit,front
min 1.0 mm (Friction padonly, without backingplate. The wear indicators(grooves) must be clearlyvisible.)
If the wear indicating marks areno longer clearly visible:Have the brake pads replacedby a specialist workshop,
preferably an authorised BMWMotorrad dealer.
Checking brake padthickness, rear brakesMake sure the ground is leveland firm and place the motor-cycle on its stand.
Visually inspect brake pads 1from the right to ascertain theirthickness.
889
z Mai
nte
nan
ce
Brake-pad wear limit, rear
min 1.0 mm (Friction padonly, without backing plate.The wear indicators must beclearly visible.)
If the wear indicating mark is nolonger visible:Have the brake pads replacedby a specialist workshop,preferably an authorised BMWMotorrad dealer.
Brake fluidChecking brake-fluidlevel, front brakesMake sure the ground is leveland firm and hold the motor-cycle upright.with centre standOE
Make sure the ground is leveland firm and place the motor-cycle on its centre stand.
Move the handlebars to thestraight-ahead position.
Check the brake fluid level infront reservoir 1.
Wear of the brake padscauses the brake fluid level
in the reservoir to sink.
Brake fluid level, front(visual inspection)
DOT4 brake fluid
It is impermissible for thebrake fluid level to drop be-low the MIN mark.
If the brake fluid level drops be-low the permitted level:Have the defect rectified asquickly as possible by a spe-cialist workshop, preferably
890
z Mai
nte
nan
ce
an authorised BMW Motorraddealer.
Checking brake-fluidlevel, rear brakesMake sure the ground is leveland firm and hold the motor-cycle upright.with centre standOE
Make sure the ground is leveland firm and place the motor-cycle on its centre stand.
Check the brake fluid level inrear reservoir 1.
Wear of the brake padscauses the brake fluid level
in the reservoir to sink.
Brake fluid level, rear(visual inspection)
DOT4 brake fluid
It is impermissible for thebrake fluid level to drop be-low the MIN mark.
If the brake fluid level drops be-low the permitted level:Have the defect rectified asquickly as possible by a spe-cialist workshop, preferably
an authorised BMW Motorraddealer.
CoolantChecking coolant levelMake sure the ground is leveland firm and place the motor-cycle on its stand.
Check the coolant level in ex-pansion tank 1. Viewing direc-tion: Between windscreen andright side panel.
891
z Mai
nte
nan
ce
Coolant, specified level
Antifreeze
between MIN and MAXmarks on the expansion tank
If the coolant level is too low:Top up the coolant.
Topping up coolantTurn the cap of the coolantfiller neck counter-clockwise toopen.Using a suitable funnel, top upwith coolant until the level iscorrect.
Turn the cap of the coolantfiller neck clockwise to close.
ClutchChecking clutch operationPull the clutch lever.The pressure point must beclearly perceptible.
If the pressure point is not clearlyperceptible:Have the clutch checked by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
TyresChecking tyre tread depth
Your motorcycle's handlingand grip can be impaired
even before the tyres wear tothe minimum tyre tread depthpermitted by law.Have the tyres changed in goodtime before they wear to the
minimum permissible treaddepth.
Make sure the ground is leveland firm and place the motor-cycle on its stand.Measure the tyre tread depthin the main tread grooves withwear marks.
Tyres have wear indicatorsintegrated into the main
tread grooves. The tyre is wornout when the tyre tread has worndown to the level of the marks.The locations of the marks areindicated on the edge of the tyre,e.g. by the letters TI, TWI or byan arrow.
If the tyre tread no longer com-plies with the minimum legallyrequired tread depth:Replace tyre.
892
z Mai
nte
nan
ce
RimsVisual inspectionMake sure the ground is leveland firm and place the motor-cycle on its stand.Visually inspect the rims fordefects.Have damaged rims checkedand, if necessary, replaced by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Checking spokesMake sure the ground is leveland firm and place the motor-cycle on its stand.Draw the handle of a screw-driver or a similar instrumentacross the spokes and listento the notes of the individualspokes.
If the notes vary:Have the spokes checked by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
ChainLubricating chain
Dirt, dust and inadequatelubrication will result in ac-
celerated wear and significantlyshorten the drive chain's usefullife.Clean and lubricate the drivechain at regular intervals.
Lubricate the drive chain every1000 km at the latest. Lubric-ate the chain more frequently ifthe motorcycle is ridden in wet,dusty or dirty conditions.Switch the ignition off and se-lect neutral.
Clean the drive chain with asuitable cleaning product, dry itand apply chain lubricant.Wipe off excess lubricant.
Checking chain tensionMake sure the ground is leveland firm and place the motor-cycle on its stand.
Use a screwdriver to push thechain up and down and meas-ure difference A.
893
z Mai
nte
nan
ce
Chain deflection
35...45 mm (Motorcycle withno weight applied, supportedon its side stand)
If measured value is outside per-mitted tolerance:Adjust the chain tension( 94)
Adjusting chain tensionMake sure the ground is leveland firm and place the motor-cycle on its stand.
Slacken quick-release axlenut 1.Slacken locknuts 2 on left andright by turning them counter-clockwise.Use adjusting screws 3 on leftand right to adjust chain ten-sion.Turning screws clockwise: re-duces chain tension.Turning screws counter-clock-wise: increases chain tension.Check the chain tension( 93)
Make sure that scale read-ings 4 are the same on left andright.Tighten locknuts 2 on left andright by turning them clock-wise.
Locknut of the final-drivechain tensioning screw
19 NmTighten quick-release axlenut 1 to the specified tight-ening torque.
Rear quick-release axle inswinging arm
100 Nm
Checking chain wearMake sure the ground is leveland firm and place the motor-cycle on its stand.
894
z Mai
nte
nan
ce
Pull the chain back at the rear-most point of the sprocket.The tips of the sprocket teethmust remain inside the chainlinks.
If the chain can be pulled backfar enough to expose the tips ofthe sprocket teeth:Consult a specialist workshop,preferably an authorised BMWMotorrad dealer.
WheelsTyre recommendationFor each size of tyre BMW Mo-torrad tests certain makes, andapproves those that it certifiesas roadworthy. If BMW Motorradhas not approved the wheels andtyres, it cannot assess their suit-ability or provide any guaranteeof road safety.Use only wheels and tyres ap-proved by BMW Motorrad foryour type of motorcycle.You can obtain detailed informa-tion from your authorised BMWMotorrad dealer or on the Inter-net at www.bmw-motorrad.com.
Effect of wheel sizeon suspension-controlsystemsWheel size is very important as aparameter for the ABS. In partic-ular, the diameter and the widthof a motorcycle's wheels are pro-
grammed into the control unitand are fundamental to all cal-culations. Any change in theseinfluencing variables, caused forexample by a switch to wheelsother than those installed ex-works, can have serious effectson the performance of the sys-tem.The sensor rings are essential forcorrect road-speed calculation,and they too must match themotorcycle's system and con-sequently cannot be changed.If you decide that you would liketo fit non-standard wheels toyour motorcycle, it is very im-portant to consult a specialistworkshop beforehand, preferablyan authorised BMW Motorraddealer. In some cases, the dataprogrammed into the control unitcan be changed to suit the newwheel sizes.
895
z Mai
nte
nan
ce
Remove the front wheelMake sure the ground is leveland firm and place the motor-cycle on its stand.
Once the calipers havebeen removed, there is
a risk of the brake pads beingpressed together to the extentthat they cannot be slipped backover the brake disc on reas-sembly.Do not operate the handbrakelever when the brake calipershave been removed.
Remove securing screws 1from the right brake caliper.
Force the brake pads slightlyapart by rocking brake caliper 2back and forth A against brakedisc 3.Mask off the parts of the wheelrim that could be scratched inthe process of removing thebrake caliper.Carefully pull the brake caliperback and out until clear of thebrake disc.
Place the motorcycle on a suit-able auxiliary stand.with centre standOE
Make sure the ground is leveland firm and place the motor-cycle on its centre stand.
with BMW Motorrad ABSOE
Remove screw 1 and removethe ABS sensor from its bore.
Raise front of motorcycle untilthe front wheel can turn freely.BMW Motorrad recommendsthe BMW Motorrad front-wheelstand for lifting the motorcycle.
896
z Mai
nte
nan
ce
Install the front wheel stand( 102)
Slacken right axle clampingscrews 2.
Remove axle screw 3.
Slacken left axle clampingscrews 4.Push the axle in as far as it willgo.
Remove axle 5, while support-ing the wheel.Do not remove the grease fromthe axle.Roll the front wheel forward toremove.
Remove spacing bushing 6from the left-hand side of thewheel hub.
Installing front wheelThreaded fasteners nottightened to the specified
torque can work loose or theirthreads can suffer damage.Always have the security of thefasteners checked by a specialistworkshop, preferably an author-ised BMW Motorrad dealer.
897
z Mai
nte
nan
ce
Slip spacing bushing 6 ontothe left-hand side of the wheelhub.
The front wheel must beinstalled right way round to
rotate in the correct direction.Note the direction-of-rotation ar-rows on the tyre or the wheelrim.
Roll the front wheel into posi-tion between the forks, makingsure that the brake disc passesbetween the brake pads of thebrake caliper on the left.
Raise the front wheel and in-sert axle 5 until seated.Tighten right axle clampingscrews 2 to the specifiedtorque or install a suitabletool to counter-hold for thenext step in the assemblyprocedure.
Clamp of quick-releaseaxle
Tightening sequence: 2xeach side, alternately
19 Nm
Install axle screw 3 and tight-en to the specified tighteningtorque.
Quick-release axle, front,in axle holder
30 NmTighten left axle clampingscrews 4 to the specifiedtightening torque.
Clamp of quick-releaseaxle
Tightening sequence: 2xeach side, alternately
898
z Mai
nte
nan
ce
Clamp of quick-releaseaxle
19 Nm
If applicable, slacken right axleclamping screws 2 again.Remove the front-wheel stand.
Ease the right brake caliperonto the brake disc.
Tighten securing screws 1 tothe specified tightening torque.
Brake caliper to fork leg
38 NmRemove the adhesive tapefrom the wheel rim.Operate the brake severaltimes until the brake pads arebedded.
Firmly compress the front forksseveral times.
Tighten right axle clampingscrews 2 to the specified tight-ening torque.
Clamp of quick-releaseaxle
Tightening sequence: 2xeach side, alternately
19 Nm
899
z Mai
nte
nan
ce
with BMW Motorrad ABSOE
Insert the ABS sensor into itsbore and install screw 1.
Remove the auxiliary stand, ifinstalled beforehand.
Removing rear wheelPlace the motorcycle on a suit-able auxiliary stand.with centre standOE
Make sure the ground is leveland firm and place the motor-cycle on its centre stand.
Remove screw 1 of the speedsensor and remove the speedsensor from the holder.
Remove axle nut 2.
Slacken locknuts 3 on left andright by turning them counter-clockwise.Back off adjusting screws 4 onleft and right by turning themcounter-clockwise.Remove adjusting plate 5 andpush the axle in as far as it willgo.
Remove quick-release axle 6and remove adjusting plate 7.
8100
z Mai
nte
nan
ce
Roll the rear wheel as far for-ward as possible and disen-gage chain 8 from the sprock-et.Roll the rear wheel back until itis clear of the swinging arm.
The sprocket and thespacer sleeves on left
and right are loose fits in thewheel. Make sure that theseparts are not damaged or lost onremoval.
Installing rear wheelRoll the rear wheel into theswinging arm, making sure that
the brake disc passes betweenthe brake pads.
Roll the rear wheel as farforward as possible and loopchain 8 over the sprocket.
Seat left adjusting plate 7 inthe swinging arm and installquick-release axle 6 in thebrake caliper and the rearwheel.Make sure that the axle fits in-to the recess of the adjustingplate.
8101
z Mai
nte
nan
ce
Install right adjusting plate 5.
Install nut 2, but do not tightenit at this point.
Seat the speed sensor in theholder and install screw 1 ofthe speed sensor.Adjust the chain tension( 94)Remove the auxiliary stand, ifinstalled beforehand.
Front-wheel standInstalling front wheelstand
The BMW Motorrad frontwheel stand is not designed
to support the motorcyclewithout the assistance of anauxiliary stand. A motorcycle
resting only on the front wheelstand and the rear wheel cantopple.Place the motorcycle on an aux-iliary stand before lifting the frontwheel with the BMW Motorradfront-wheel stand.
Place the motorcycle on a suit-able auxiliary stand.with centre standOE
Place the motorcycle on itscentre stand.
Use basic stand (0 402 241)with front-wheel adapter(0 402 242).
8102
z Mai
nte
nan
ce
Slacken adjusting screws 1.Push the two adapters 2 apartuntil the front forks fit betweenthem. Adjust the adapter studsto suit the front suspension.Use locating pins 3 to set thefront-wheel stand to the de-sired height.Centre the front-wheel standrelative to the front wheel andpush it against the front axle.
Align the two adapters 2 sothat the front forks are securelyseated.Tighten adjusting screws 1.
Apply uniform pressure to pushthe front-wheel stand downand raise the motorcycle.
with centre standOE
If the motorcycle is raisedtoo far the centre stand will
lift clear of the ground and themotorcycle could topple to oneside.When raising the motorcycle,make sure that the centre standremains on the ground. If ne-cessary, adjust the height of thefront-wheel stand.
Apply uniform pressure to pushthe front-wheel stand downand raise the motorcycle.
BulbsGeneral instructionsA warning appears in the multi-function display if a bulb is de-fective.
A defective bulb placesyour safety at risk because
it is easier for other users tooversee the motorcycle.Replace defective bulbs assoon as possible; always carry acomplete set of spare bulbs ifpossible.
The bulb is pressurised andcan cause injury if dam-
aged.Wear protective goggles andgloves when changing bulbs.
8103
z Mai
nte
nan
ce
The types of bulb fitted toyour motorcycle are listed
in the section entitled "Technicaldata".
Do not touch the glass ofnew bulbs with your fingers.
Use a clean, dry cloth to holdthe bulbs when handling them.Dirt deposits, in particular oil andgrease, interfere with heat radi-ation from the bulb. This leadsto overheating and shortens thebulb's operating life.
Replacing low-beamheadlight bulbMake sure the ground is leveland firm and place the motor-cycle on its stand.
Remove cover of low-beamheadlight 1 by turning itcounter-clockwise.
Replacing low-beam and high-beam headlight bulb ( 105)
Turn cover of low-beam head-light 1 clockwise to install.
Replacing high-beamheadlight bulb
Remove cover of high-beamheadlight 1 by turning itcounter-clockwise.
Replacing low-beam and high-beam headlight bulb ( 105)
8104
z Mai
nte
nan
ce
Turn cover of high-beam head-light 1 clockwise to install.
Replacing low-beam andhigh-beam headlight bulb
Disconnect plug 1.
Disengage spring clips 2 fromthe fastenings and swing themaside.Remove bulb 3.
Replace the defective bulb.
Bulb for low-beam head-light
H7 / 12 V / 55 W
Bulb for high-beamheadlight
H7 / 12 V / 55 W
Install bulb 3, making sure thatalignment is correct.Close and lock spring clips 2.
Connect plug 1.
8105
z Mai
nte
nan
ce
Replacing parking-lightbulbMake sure the ground is leveland firm and place the motor-cycle on its stand.
Remove cover of low-beamheadlight 1 by turning itcounter-clockwise.
Pull parking-light bulb 1 out ofthe headlight housing.
Remove the bulb from the bulbholder.
Replace the defective bulb.
Bulb for parking light
W5W / 12 V / 5 W
Insert the bulb into the bulbsocket.
8106
z Mai
nte
nan
ce
Insert parking-light bulb 1 intothe headlight housing.
Turn cover of low-beam head-light 1 clockwise to install.
Replacing turn indicatorbulbs, front and rearMake sure the ground is leveland firm and place the motor-cycle on its stand.Switch off the ignition.
Remove screw 1.
Pull the glass out of the reflect-or housing at the threaded-fastener side.
Turn bulb 2 counter-clockwiseand remove it from the bulbhousing.
8107
z Mai
nte
nan
ce
Replace the defective bulb.
Bulbs for flashing turnindicators, front
R10W / 12 V / 10 W
with LED turn indicatorsOA
LED / 12 V
Turn bulb 2 clockwise to installit in the bulb housing.
Working from the inboard side,insert the glass into the bulbhousing and close the housing.
Install screw 1.
Replacing brake light andrear light bulbThe LED rear light can be re-placed only as a complete unit.Consult a specialist workshop,preferably an authorised BMWMotorrad dealer.
Replacing number-platelight bulbsMake sure the ground is leveland firm and place the motor-cycle on its stand.
8108
z Mai
nte
nan
ce
Remove screw 1 from themudguard cover and removethe cover.
Pull bulb holder 2 out of thelight carrier.
Pull the bulb out of the bulbsocket.
Replace the defective bulb.
Bulb for number-platelight
W5W / 12 V / 5 W
Insert the bulb into the bulbsocket.
Seat bulb holder 2 in the lightcarrier.
8109
z Mai
nte
nan
ce
Hold the mudguard cover inposition and install screw 1.
Air filterRemoving air filterRemove the centre trim panel( 115)
Remove screws 1.Remove air-filter cover 2.
Remove air filter 3.
Installing air filter
Install air filter 3.
Hold air-filter cover 2 in posi-tion.Install screws 1.
8110
z Mai
nte
nan
ce
Install the centre trim panel( 115)
Jump startingThe wires leading to thepower socket do not have
a load-capacity rating adequatefor jump-starting the engine. Ex-cessively high current can leadto a cable fire or damage to thevehicle electronics.Do not use the on-board socketto jump-start the engine of themotorcycle.
Touching live parts of theignition system with the
engine running can cause electricshock.Do not touch parts of the igni-tion system when the engine isrunning.
A short-circuit can res-ult if the crocodile clips
of the jump leads are accident-
ally brought into contact with themotorcycle.Use only jump leads fitted withfully insulated crocodile clips atboth ends.
Jump-starting with a donor-battery voltage higher than
12 V can damage the vehicleelectronics.Make sure that the battery of thedonor vehicle has a voltage ratingof 12 V.
Remove the centre trim panel( 115)When jump-starting the engine,do not disconnect the batteryfrom the on-board electricalsystem.
Run the engine of the donorvehicle during jump-starting.Begin by connecting one endof the red jump lead to posit-ive terminal 2 of the dischargedbattery and the other end tothe positive terminal of thedonor battery.Then connect one end of theblack jump lead to the negativeterminal of the donor batteryand the other end to negativeterminal 1 of the dischargedbattery.Start the engine of the vehiclewith the discharged batteryin the usual way; if the en-
8111
z Mai
nte
nan
ce
gine does not start, wait a fewminutes before repeating theattempt in order to protect thestarter motor and the donorbattery.Allow both engines to idle for afew minutes before disconnect-ing the jump leads.Disconnect the jump lead fromthe negative terminals 1 first,then disconnect the secondjump lead from the positiveterminals 2.
Do not use proprietarystart-assist sprays or oth-
er products to start the engine.
Install the centre trim panel( 115)
BatteryMaintenance instructionsCorrect upkeep, recharging andstorage will prolong the life ofthe battery and are essential if
warranty claims are to be con-sidered.Compliance with the points be-low is important in order to max-imise battery life:Keep the surface of the batteryclean and dryDo not open the batteryDo not top up with waterBe sure to read and complywith the instructions for char-ging the battery on the follow-ing pagesDo not turn the battery upsidedown
If the battery is not discon-nected, the on-board elec-
tronics (e.g. clock, etc.) graduallydrain the battery. This can causethe battery to run flat. If this hap-pens, warranty claims will not beaccepted.If the motorcycle is to be out ofuse for more than four weeks,disconnect the battery or con-
nect a suitable trickle charger tothe battery.
BMW Motorrad has de-veloped a float charger spe-
cially designed for compatibilitywith the electronics of your mo-torcycle. Using this charger, youcan keep the battery chargedduring long periods of disuse,without having to disconnect thebattery from the motorcycle'son-board systems. You can ob-tain additional information fromyour authorised BMW Motorraddealer.
Charging battery whenconnected
Charging the connectedbattery directly at the bat-
tery terminals can damage thevehicle electronics.Always disconnect the batteryfrom the on-board circuits be-fore recharging it with a charger
8112
z Mai
nte
nan
ce
connected directly to the batteryposts.
Only chargers suitable forthis mode of charging can
be used to recharge the batteryvia the on-board socket. Unsuit-able chargers could cause dam-age to the motorcycle's on-boardelectrics.Use BMW chargers with thepart numbers 71 60 7 688 864(220 V) or, as applicable,71 60 7 688 865 (110 V). Ifyou are in doubt, disconnectthe battery from the on-boardsystems and connect the chargerdirectly to the battery.
If you switch on the igni-tion and the multifunction
display and telltale lights fail tolight up, the battery is completelyflat. Attempting to charge a com-pletely flat battery via the on-board socket can cause damageto the motorcycle's electronics.
If a battery has discharged to theextent that it is completely flat, ithas to be disconnected from theon-board circuits and chargedwith the charger connected dir-ectly to the battery posts.
Charge via the power sock-et, with the battery connectedto the motorcycle's on-boardelectrical system.
The motorcycle's on-boardelectronics know when the
battery is fully charged. Theon-board socket is switched offwhen this happens.
Comply with the operating in-structions of the charger.
If you are unable to chargethe battery through the on-
board socket, you may be usinga charger that is not compatiblewith your motorcycle's electron-ics. If this happens, disconnectthe battery from the on-board
systems and connect the chargerdirectly to the battery.
Charging battery whendisconnectedCharge the battery using asuitable charger.Comply with the operating in-structions of the charger.Once the battery is fullycharged, disconnect thecharger's terminal clips fromthe battery terminals.
The battery has to be re-charged at regular intervals
in the course of a lengthy periodof disuse. See the instructionsfor caring for your battery. Al-ways fully recharge the batterybefore restoring it to use
Remove the batteryRemove the centre trim panel( 115)
8113
z Mai
nte
nan
ce
Switch off the ignition.
Disconnection in the wrongsequence increases the risk
of short-circuits.Always proceed in the correctsequence.
Begin by removing threadedfastener 1 of the negative lead.Then remove threaded fasten-er 2 of the positive lead.Remove screws 3 on left andright and remove the batteryretainer.
Lift the battery up and out;work it slightly back and forthif it is difficult to remove.
Installing batteryIf the battery was discon-nected from the motorcycle
for a prolonged period of timeit will be necessary to enter thecurrent date in the instrumentpanel, in order to ensure that theservice-due indicator functionscorrectly.If you want to have the date setconsult a specialist workshop,preferably an authorised BMWMotorrad dealer.
Insert the battery into the bat-tery compartment, with thepositive terminal on the rightin the direction of travel.
Place the battery retainer inposition, making sure that theleads are correctly routed atposition 4.Install screws 3 on left andright.
Connection in the wrongsequence increases the risk
of short-circuits.Always proceed in the correctsequence.
Install screw 2 securing thepositive lead.Then install screw 1 securingthe negative lead.
8114
z Mai
nte
nan
ce
Install the centre trim panel( 115)Set the clock ( 38)
Removing centre trimpanelRemove the seat ( 55)
Remove screws 1 on left andright.
Remove four screws 2.Disconnect the plug from thesocket.Remove the centre trim panel.
Installing centre trimpanelConnect the plug to the sock-et.
Manoeuvre the centre trimpanel into position. Make surethat all three tabs 3 on left andright engage the side panels.
Install four screws 2.
8115
z Mai
nte
nan
ce
Care
Care
Care products . . . . . . . . . . . . . . . . . . . . . 118
Washing motorcycle . . . . . . . . . . . . . . . 118
Cleaning easily damaged compon-ents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Paint care . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Protective wax coating . . . . . . . . . . . . . 120
Laying up motorcycle . . . . . . . . . . . . . . 120
Restoring motorcycle to use . . . . . . . 120
9117
z Car
e
Care productsBMW Motorrad recommendsthat you use the cleaning andcare products you can obtainfrom your authorised BMW Mo-torrad dealer. The substances inBMW Care Products have beentested in laboratories and in prac-tice; they provide optimised careand protection for the materialsused in your vehicle.
The use of unsuitablecleaning and care products
can damage vehicle components.Do not use solvents such as cel-lulose thinners, cold cleaners,fuel or the like, and do not usecleaning products that containalcohol.
Washing motorcycleBMW Motorrad recommendsthat you use BMW insect re-mover to soften and wash offinsects and stubborn dirt on
painted parts prior to washingthe motorcycle.To prevent stains, do not washthe motorcycle immediately afterit has been exposed to strongsunlight and do not wash it in thesun.Make sure that the motorcycleis washed frequently, especiallyduring the winter months.To remove road salt, clean themotorcycle with cold water im-mediately after every trip.
After the motorcycle hasbeen washed, ridden
through water or ridden inthe rain, the brake discs andpads might be wet and thebrakes might not take effectimmediately.Apply the brakes in good timeuntil the brakes have dried out.
Warm water intensifies theeffect of salt.
Use only cold water to wash offroad salt.
The high pressure of steamcleaners can damage seals,
the hydraulic brake system, theelectrical system, and the seat.Do not use a steam jet or high-pressure cleaning equipment.
Cleaning easilydamaged componentsPlasticsClean plastic parts with waterand BMW plastic care emulsion.This includes in particular:Windscreen and slipstream de-flectorsHeadlight lens made of plasticGlass cover of the instrumentclusterBlack, unpainted parts
If plastic parts are cleanedusing unsuitable cleaning
9118
z Car
e
agents, the surfaces can be dam-aged.Do not use cleaning agents thatcontain alcohol, solvents or ab-rasives to clean plastic parts.Even fly-remover pads or clean-ing pads with hard surfaces canproduce scratches.
Soften stubborn dirt andinsects by covering the af-
fected areas with a wet cloth.
WindscreenClean off dirt and insects with asoft sponge and plenty of water.
Fuel and chemical solventsattack the material of the
windscreen; the windscreen be-comes opaque or dull.Do not use cleaning agents.
ChromeUse plenty of water and BMWshampoo to clean chrome, par-ticularly if it has been exposed toroad salt. Use chrome polish foradditional treatment.
RadiatorClean the radiator regularly toprevent overheating of the en-gine due to inadequate cooling.For example, use a garden hosewith low water pressure.
Cooling fins can be benteasily.
Take care not to bend the finswhen cleaning the radiator.
RubberTreat rubber components withwater or BMW rubber-careproducts.
Using silicone sprays forthe care of rubber seals can
cause damage.
Do not use silicone sprays orother care products that containsilicon.
Paint careWashing the motorcycle regularlywill help counteract the long-termeffects of substances that dam-age the paint, especially if yourmotorcycle is ridden in areaswith high air pollution or naturalsources of dirt, for example treeresin or pollen.Remove particularly aggressivesubstances immediately, how-ever, as otherwise the paint canbe affected or become discol-oured. Substances of this natureinclude spilt fuel, oil, grease,brake fluid and bird droppings.We recommend BMW vehiclepolish or BMW paint cleaner forthis purpose.Marks on the paintwork are par-ticularly easy to see after themotorcycle has been washed.
9119
z Car
e
Remove stains of this kind im-mediately, using cleaning-gradebenzene or petroleum spirit on aclean cloth or ball of cotton wool.BMW Motorrad recommendsBMW tar remover for removingspecks of tar. Remember to waxthe parts treated in this way.
Protective wax coatingBMW Motorrad recommendsapplying only BMW car wax orproducts containing carnaubawax or synthetic wax.It is time to rewax the paint-work when water "puddles" onthe surface, instead of formingbeads.
Laying up motorcycleClean the motorcycle.Remove the battery.Spray the brake and clutchlever pivots, the side standpivots and the centre standpivots (if the motorcycle is fit-
ted with a centre stand) with asuitable lubricant.Coat bright metal and chrome-plated parts with an acid-freegrease (e.g. Vaseline).Stand the motorcycle in a dryroom in such a way that thereis no load on either wheel.
Before laying the vehicleup out of use, have the en-
gine oil and the oil filter elementchanged by a specialist work-shop, preferably an authorisedBMW Motorrad dealer. Com-bine work for laying up/restoringto use with a BMW service orinspection.
Restoring motorcycleto useRemove the protective waxcoating.Clean the motorcycle.Install a charged battery.
Before starting: work throughthe checklist.9
120
z Car
e
Technical data
Technical data
Troubleshooting chart . . . . . . . . . . . . . 122
Threaded fasteners . . . . . . . . . . . . . . . . 123
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Transmission . . . . . . . . . . . . . . . . . . . . . . 127
Rear-wheel drive . . . . . . . . . . . . . . . . . . . 128
Running gear . . . . . . . . . . . . . . . . . . . . . . 128
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Wheels and tyres . . . . . . . . . . . . . . . . . . 129
Electrics . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 133
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Riding specifications . . . . . . . . . . . . . . . 13410121
z Tec
hn
ical
dat
a
Troubleshooting chartPossible cause Remedy
Emergency off switch (kill switch) Kill switch in operating position (run).
Side stand Retract the side stand ( 60).
Gear engaged and clutch not disengaged. Select neutral or pull clutch lever ( 60).
Clutch pulled before ignition was switched on Switch on the ignition, then pull the clutch lever.
No fuel in tank Refuel ( 66)
Battery flat Charge the battery when connected ( 112)
10122
z Tec
hn
ical
dat
a
Threaded fastenersFront wheel Value Valid
Brake caliper to fork leg
M10 x 40 38 Nm
Clamp of quick-release axle
M8 x 25 2x each side, alternately
19 Nm
Quick-release axle, front, in axleholder
M14 x 1.5 30 Nm
Rear wheel Value Valid
Rear quick-release axle inswinging arm
M16 x 1.5 100 Nm
Mirror arm Value Valid
Mirror to clamping element
M14 x 1 20 Nm
10123
z Tec
hn
ical
dat
a
Mirror arm Value Valid
Clamping element to clampingblock
M10 30 Nm
Chain Value Valid
Locknut of the final-drive chaintensioning screw
M8 19 Nm
10124
z Tec
hn
ical
dat
a
Engine
Engine design Two-cylinder four-stroke, DOHC with chain-and-sprocket drive, 4 valves operated by cam follow-ers, balancing conrod, liquid-cooled cylinders andheads, integral water pump, 6-speed gearbox anddry sump lubrication
Displacement 798 cm3
Cylinder bore 82 mm
Piston stroke 75.6 mm
Compression ratio 12 : 1
Nominal output 63 kW, - at engine speed: 7500 min-1
with regular unleaded (RON 91)OE 61 kW, - at engine speed: 7500 min-1
Torque 83 Nm, - at engine speed: 5750 min-1
with regular unleaded (RON 91)OE 81 Nm, - at engine speed: 5750 min-1
Maximum engine speed max 9000 min-1
Idle speed 1250+50 min-1
10125
z Tec
hn
ical
dat
a
Fuel
Recommended fuel grade 95 ROZ/RON, Super unleaded
with regular unleaded (RON 91)OE 91 ROZ/RON, Regular unleaded (fuel grade, us-able with power- and consumption-related restric-tions)
Usable fuel capacity approx. 16 l
Reserve fuel ≥4 l
Engine oil
Engine oil, capacity 2.9 l, with filter change2.7 l, without filter change0.3 l, additional, if swing-arm shaft cover is re-moved
Lubricant Engine oil, 10W-40
Oil grades Mineral oils of API classification SF through SH.BMW Motorrad recommends not using oil addit-ives, because they can have a detrimental effecton clutch operation. Please do not hesitate tocontact your authorised BMW Motorrad dealerif you have any questions relating the choice of asuitable engine oil for your motorcycle.
10126
z Tec
hn
ical
dat
a
Permissible viscosity classes
SAE 10 W-40 ≥-20 °C, Operation at low temperatures
SAE 15 W-40 ≥-10 °C
Clutch
Clutch type Multiplate clutch running in oil bath
Transmission
Gearbox type Claw-shift 6-speed gearbox, integrated into en-gine block
Gearbox transmission ratios 1.943 (35/68 teeth), Primary transmission ratio1:2.462 (13/32 teeth), 1st gear1:1.750 (16/28 teeth), 2nd gear1:1.381 (21/29 teeth), 3rd gear1:1.174 (23/27 teeth), 4th gear1:1.042 (24/25 teeth), 5th gear1:0.960 (25/24 teeth), 6th gear
10127
z Tec
hn
ical
dat
a
Rear-wheel drive
Type of final drive Chain drive
Type of rear suspension Two-arm cast-aluminium swinging arm
Final drive, number of teeth (Pinion / sprocket) 16 / 42
Running gear
Front wheel
Type of front suspension Upside-down telescopic fork
Spring travel, front 230 mm, At wheel
Rear wheel
Type of rear suspension Two-arm cast-aluminium swinging arm
Type of rear suspension Direct-pivot central spring strut with steplesslyadjustable rebound-stage damping
Spring travel at rear wheel 215 mm, At wheel
10128
z Tec
hn
ical
dat
a
Brakes
Front wheel
Type of front brake Hydraulically operated twin disc brake with 2-pis-ton floating calipers and floating brake discs
Brake-pad material, front Sintered metal
Rear wheel
Type of rear brake Hydraulically operated disc brake with 1-pistonfloating caliper and fixed disc
Brake-pad material, rear Organic material
Wheels and tyres
Recommended tyre sets You can obtain an up-to-date list of approvedtyres from your authorised BMW Motorrad dealeror on the Internet at "www.bmw-motorrad.com".
Front wheel
Front wheel, type Spoked wheel, MT H2
Front wheel rim size 2.15" x 21"
Tyre designation, front 90 / 90 - 21
10129
z Tec
hn
ical
dat
a
Rear wheel
Rear wheel type Spoked wheel, MT H2
Rear wheel rim size 4.25" x 17"
Tyre designation, rear 150 / 70 - 17
Tyre pressure
Tyre pressure, front 2.2 bar, one-up, at tyre temperature: 20 °C2.5 bar, two-up and/or with luggage, at tyre tem-perature: 20 °C
Tyre pressure, rear 2.5 bar, one-up, at tyre temperature: 20 °C2.9 bar, two-up and/or with luggage, at tyre tem-perature: 20 °C
10130
z Tec
hn
ical
dat
a
Electrics
Electrical rating of on-board socket 5 A
Fuses Electronic fuses protect all the circuits. If an elec-tronic fuse trips and de-energises a circuit, thecircuit is active as soon as the ignition is switchedon after the fault has been rectified.
Battery
Battery, manufacturer and designation Exide ETX14-BS
Battery type AGM (Absorbent Glass Mat) battery
Battery rated voltage 12 V
Battery rated capacity 14 Ah
Spark plugs
Spark plugs, manufacturer and designation NGK DCPR 8 E
Electrode gap of spark plug 0.9±0 mm, When newmax 1.2 mm, Wear limit
10131
z Tec
hn
ical
dat
a
Lighting
Bulb for high-beam headlight H7 / 12 V / 55 W
Bulb for low-beam headlight H7 / 12 V / 55 W
Bulb for parking light W5W / 12 V / 5 W
Bulb for tail light/brake light LED / 12 V
Bulb for number-plate light W5W / 12 V / 5 W
Bulbs for flashing turn indicators, front R10W / 12 V / 10 W
with LED turn indicatorsOA LED / 12 V
Bulbs for flashing turn indicators, rear R10W / 12 V / 10 W
with LED turn indicatorsOA LED / 12 V
10132
z Tec
hn
ical
dat
a
Frame
Frame type Tubular spaceframe
Type plate location Steering head, front top
VIN location Steering head, right
Dimensions
Length of motorcycle 2320 mm, across front wheel to number-platecarrier
Height of motorcycle 1350 mm, without rider at DIN unladen weight
Width of motorcycle 870 mm, across mirrors without mirrors
Front-seat height 880 mm, Without rider at unladen weight
with dual seat, lowOE 850 mm, Without rider at unladen weight
Rider's inside-leg arc, heel to heel 1940 mm
with dual seat, lowOE 1900 mm, Without rider at unladen weight
10133
z Tec
hn
ical
dat
a
Weights
Unladen weight 207 kg, DIN unladen weight, ready for road, 90 %load of fuel, without optional extras
Permissible gross weight 443 kg
Maximum payload 236 kg
Riding specifications
Top speed >200 km/h
10134
z Tec
hn
ical
dat
a
Service
Service
BMW Motorrad service . . . . . . . . . . . . 136
BMW Motorrad service quality . . . . . 136
BMW Motorrad Service Card: on-the-spot breakdown assistance . . . . 136
BMW Motorrad service network . . . 137
Maintenance work . . . . . . . . . . . . . . . . . 137
Confirmation of maintenancework . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Confirmation of service . . . . . . . . . . . . 143
11135
z Ser
vice
BMW Motorrad serviceAdvanced technology requiresspecially adapted methods ofmaintenance and repair.
If maintenance and re-pair work is performed in-
expertly, it could result in con-sequential damage and thus con-stitute a safety risk.BMW Motorrad recommends youto have all the associated workon your motorcycle carried outby a specialist workshop, prefer-ably an authorised BMW Motor-rad dealer.
Your authorised BMW Motorraddealer can provide information onBMW services and the work un-dertaken as part of each service.Have all maintenance and repairwork carried out confirmed in the"Service" chapter in this manual.Authorised BMW Motorrad deal-ers are supplied with the latesttechnical information and have
the necessary technical know-how. BMW Motorrad recom-mends that you contact your au-thorised BMW Motorrad dealerif you have questions regardingyour motorcycle.
BMW Motorrad servicequalityAlong with its reputation for en-gineering quality and high reliab-ility, BMW Motorrad is a bywordfor excellent quality of service.To ensure that your BMW is al-ways in optimum condition, BMWMotorrad recommends that youhave the maintenance work re-quired for your motorcycle car-ried out regularly, preferably byyour authorised BMW Motor-rad dealer. For generous treat-ment of claims submitted afterthe warranty period has expired,evidence of regular maintenanceis essential.
Certain signs of wear, moreover,may otherwise not be noticeduntil it is too late to put themright at moderate cost. Your au-thorised BMW Motorrad dealer'smechanics know every detail ofyour motorcycle and can take re-medial action if necessary beforeminor faults develop into seriousproblems. By having the neces-sary repairs done properly andin good time, you save time andmoney in the long run.
BMW Motorrad ServiceCard: on-the-spotbreakdown assistanceIn the event of a breakdown, theBMW Motorrad Service Card is-sued with each new BMW mo-torcycle enables you to accessan extensive range of servicessuch as breakdown assistance,motorcycle transportation etc.(details can differ from country tocountry). In the event of a break-
11136
z Ser
vice
down, contact the Mobile Serviceorganisation of BMW Motorrad.The specialists will provide thenecessary advice and assistance.You will find important country-specific contact addresses andthe after-sales service organisa-tion phone numbers in the "Ser-vice Kontakt / Service Contact"brochures, along with informa-tion on Mobile Service and thedealership network.
BMW Motorrad servicenetworkBMW Motorrad has an extens-ive after-sales service network inplace to look after you and yourmotorcycle in more than 100countries. In Germany alone, youhave the best possible accessto approximately 200 authorisedBMW Motorrad dealers.All information concerning the in-ternational dealership networkcan be found in the brochure
"Service Contact Europe" or"Service Contact Africa, Amer-ica, Asia, Australia, Oceania".
Maintenance workBMW Pre-delivery CheckYour authorised BMW Motorraddealer conducts the BMW pre-delivery check before handingover the motorcycle to you.
BMW Running-in CheckThe BMW running-in check hasto be performed when the mo-torcycle has covered between500 km and 1200 km
BMW ServiceThe BMW Service is carried outonce a year; the extent of servi-cing can vary, depending on theage of the motorcycle and thedistance it has covered. Your au-thorised BMW Motorrad dealerconfirms that the service workhas been carried out and enters
the date when the next servicewill be due.Riders who cover long distancesin a year might have to bring intheir motorcycles for service be-fore the next scheduled date. Itis to allow for these cases thata maximum odometer reading isentered as well in the confirma-tion of service. Servicing has tobe brought forward if this odo-meter reading is reached beforethe next scheduled date for theservice.The service-due indicator in themultifunction display reminds youabout one month or 1000 kmin advance when the time for aservice is approaching, on thebasis of the programmed values.
11137
z Ser
vice
Confirmation of maintenance work
BMW Pre-deliveryCheckCompleted
on
Stamp, signature
BMW Running-inCheckCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11138
z Ser
vice
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11139
z Ser
vice
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11140
z Ser
vice
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11141
z Ser
vice
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11142
z Ser
vice
Confirmation of serviceThe table is intended as a record of maintenance, warranty and repair work, the installation of optionalaccessories and, if appropriate, special campaign (recall) work.
Item Odometerreading
Date
11143
z Ser
vice
AAbbreviations and symbols, 6ABSControl, 16Engineering details, 70Operation, 49Self-diagnosis, 62Warnings, 30
AccessoriesGeneral instructions, 74
Air filterInstallation, 110Removal, 110Stowage, 15
Anti-theft alarmTelltale light, 18Warnings, 32
BBatteryCharging, 113Charging battery whenconnected, 112Installation, 114Maintenance instructions, 112Removal, 113
Stowage, 15Technical data, 131
BMW Motorrad service, 136BMW Motorrad ServiceCard, 136
Brake fluidChecking fluid levels, 90Reservoir, front, 13Reservoir, rear, 13
Brake padsChecking brake-padthickness, 89Running in, 63
BrakesAdjusting handlebar lever, 50Checking operation, 88Safety instructions, 63Technical data, 129
BulbsGeneral instructions, 103Overview, headlights, 19Replacing high-beam headlightbulb, 104Replacing low-beam headlightbulb, 104
Replacing number-plate lightbulbs, 108Replacing side-light bulb, 106Replacing turn indicatorbulbs, 107Technical data, 132Warning for bulb failure, 28
CCaseOperation, 77
ChainAdjusting tension, 94Checking tension, 93Checking wear, 94Lubricating, 93
Checklist, 60Clock, 22Adjusting, 38Control, 18
12145
z Ind
ex
ClutchAdjusting handlebar lever, 50Checking operation, 92Technical data, 127
Confirmation of maintenancework, 138
CoolantChecking fill level, 91Fill-level indicator, 13Filler neck, 13Temperature gauge, 23, 24Topping up, 92Warning forovertemperature, 27
Currency, 7
DDampingAdjuster, rear, 13Adjusting rear, 52
Dimensions, 133DisplaySee multifunction display, 18
EElectricsTechnical data, 131
Electronic immobiliser (EWS), 37Warning, 27
Emergency off switch (killswitch), 17Operation, 48
EngineControl, 17Starting, 60Technical data, 125Warning for engineelectronics, 28
Engine oilChecking fill level, 87Dipstick, 11Filler neck, 11Technical data, 126Topping up, 88Warning for engine oilpressure, 28
Equipment, 7
FFirst-aid kitStowage, 14
FrameTechnical data, 133
Front-wheel standInstalling, 102
FuelFill-level indicator, 23, 24Filler neck, 13Refuelling, 66Technical data, 4, 126Warning for fuel down toreserve, 27
Fuses, 131
GGear indicator, 23General viewsInstrument cluster, 18Left handlebar fitting, 16Left side of motorcycle, 11Right handlebar fitting, 17Right side of motorcycle, 13Underneath the seat, 14Underneath the trim panel, 15
12146
z Ind
ex
Grip heatingControl, 17Operation, 48
HHandlebar fittingsGeneral view, left side, 16General view, right side, 17
Hazard warning flashersControl, 16, 17Operation, 47
HeadlightBeam throw, 54Driving on right/driving onleft, 54Overview, 19
Headlight flasher, 16Helmet holder, 14, 56High-beam headlightControl, 16Switching on, 45Telltale light, 22
Horn, 16
IIdleTelltale light, 22
IgnitionSwitching off, 36Switching on, 36
ImmobiliserSee EWS, 37
Instrument clusterOverview, 18
JJump starting, 111
KKeys, 36, 38
LLaying up, 120LightsHeadlight flasher, 45Switch on the high-beamheadlight, 45Switch on the parking lights, 45Switching on the low-beamheadlight, 45Switching on the side lights, 45
Low-beam headlightSwitching on, 45
LuggageInstructions for loading andsecuring objects, 75
MMaintenance intervals, 137MirrorsAdjusting, 51
MotorcycleLaying up, 120Parking, 65Restoring to use, 120
Multifunction display, 18Status indicators, 22
OOdometer and tripmeters, 22Control, 18Operation, 38
On-board computerAmbient temperature, 40Average consumption, 41Average speed, 40Control, 16
12147
z Ind
ex
Current consumption, 41Operation, 39Range, 42Redline warning, 44Status indicators, 23Stopwatch, 42Warnings, 29
PParking, 65Parking lightSwitching on, 45
Power socket, 11, 74Pre-ride check, 61
RRear-wheel driveTechnical data, 128
Refuelling, 13, 66Reserve volumeWarning, 27
Restoring to use, 120Rev. counter, 18Rider's ManualStowage, 14
Running gearTechnical data, 128
Running in, 62
SSafety instructionsBrakes, 63General, 58
SeatInstallation, 55Lock, 11Removal, 55
Service, 136Service Card, 136Service-due indicator, 22Side lightSwitching on, 45
Spark plugsTechnical data, 131
Speedometer, 18Spring preloadAdjuster, rear, 13Adjusting rear, 51Tools, 14
Starting, 60
Status indicatorsSee also warnings, 22Standard status indicators, 22With on-board computer, 23
Steering lock, 37StopwatchControl, 18
TTechnical dataBattery, 131Brakes, 129Bulbs, 132Clutch, 127Dimensions, 133Electrics, 131Engine, 125Engine oil, 126Frame, 133Fuel, 4, 126Rear-wheel drive, 128Running gear, 128Spark plugs, 131Standards, 7Transmission, 127
12148
z Ind
ex
Weights, 134Wheels and tyres, 129
Telltale lights, 22ToolkitContents, 86Stowage, 14
TopcaseOperation, 80
Torques, 123TransmissionTechnical data, 127
TransportationLashing, 67
Troubleshooting chart, 122Turn indicatorsControl, left, 16Control, right, 17Operation, 46Telltale light, 22
Type plate, 13TyresChecking inflation pressure, 53Checking tread depth, 92Pressures, 4, 130Recommendation, 95
Running in, 63Table of tyre pressures, 14Technical data, 129
VVehicle identification number, 13
WWarning light for engine rpm, 18Warnings, 24Mode of presentation, 24With ABS, 30With anti-theft alarm, 32With on-board computer, 29
Warnings, overview, 26, 31Weights, 134Payload table, 14
WheelsChange of size, 95Checking rims, 93Installing front wheel, 97Installing rear wheel, 101Remove the front wheel, 96Removing rear wheel, 100Technical data, 129
12149
z Ind
ex