Post on 14-Apr-2020
PROFESSIONALSPEAKER SYSTEMS
2008
Established in 1949, RCF has prided itself on carrying out the design and production of its own products.
The history of the company started with a parallel development of microphone technology as well as
loudspeakers; the early microphone products were highly advanced ‘Ribbon’ designs manufactured
exclusively for some very prominent American Audio companies. This initial development soon followed
a natural progression to start the design and manufacture of innovative loudspeaker transducer technology.
Unlike most loudspeaker companies who outsource the supply of transducers we have always preferred
to design and construct completely all our own components.
Many years dedicated to studying and building audio transducers and electronics have resulted in some
notable milestones. RCF was the first company to build a 300 watt commercial amplifier in the mid sixties
and, in the same period, the first in Europe to have a high level Research Centre studying loudspeakers,
horns and compression drivers. During this period we built the first of 3 anechoic chambers that represent
the focal point of our history.
During the last ten years RCF transitioned into the forefront of active loudspeaker technology, from theintroduction of the original ART series to many prominent active products conceived and designed in our laboratories.We have over the years grown to understand the best ways to use the extra degree of freedom that an active systemoffers and in interpreting how this technology affects the transducer design. Our research and engineering facultycan today offer innovative projects with finite control of each detail, from the loudspeaker voice coil wire to thehighly efficient extended dynamic amplifier topology.
There are many different ingredients that go into creating quality products and systems. These includecomputer aided simulation software to assist the understanding of transducer behaviour and amplifier operationand the relationship of dynamics and transient response.
However it is the vast technical and practical experience that our Research and Engineering team possesthat ensures the quality of our products plus placing RCF as the market leaders in True Active Loudspeaker Technologyand transducer development.
Let your ART beat again
2
The RCF loudspeaker line incorporates a vast range of transducers covering the entire audio spectrum.We design our transducers to optimise the relationship between the purity of sound, combining the absence ofdistortion and the ability to withstand high power levels over a long period of time.
RCF develops advanced transducer technology including the application of high-tech materials such ascarbon fibre, damped titanium, Kevlar® and Mylar® hybrids. With over 50 years of design and manufacturingexperience in the market, RCF have been instrumental in technological inventions such as: “carbon fibre conemoulding’’, “double silicon spiders’’ , “inside/outside’’ voice coil winding and compression driver topology, “edgewound’’ voice coil manufacturing and pure titanium diaphragm forming. Our latest developments have resulted inutilising state of the art Neodymium magnetic materials and Direct Drive Voice Coil Assembly.
RCF active and passive speaker systems take advantage of our proprietary transducer technologies,achieving the optimum blend between state of the art components and innovative, specific designed electronics.
RCF the transducer innovators
3
PURE TITANIUM DIAPHRAGMRCF has developed an oxygen freeprocess of moulding pure titanium ultrathin films in high quality, finely controlledshaped diaphragms.Our process offers superior sonic quality,extended to the highest audiblefrequencies which guarantee consistentpower handling and reliability.
NEODYMIUM MAGNETSOur Precision Compression Drivers andWoofers are equipped with high thermalperformance with high performancelightweight Neodymium magnets, offeringadvantages in system portability andhigh frequency clarity (due to the forceof magnetic flux in the gap exceeding 2kilogauss).Specific attention has been paid tomagnetic circuit polarization for optimumthermal immunity.
OURTECHNOLOGIES
LICC LOW IMPEDANCE COMPENSATEDCROSSOVERAll our passive speakers are equippedwith high power handling low impedancecrossover designs. The low impedancecompensated crossover is an RCF first,and a breakthrough in crossover design.Conventional passive crossovers havean approximate 180 degree phase shiftbetween the woofer and tweeter at thecrossover point.Such a system cannot reproducetransients correctly, causing negativeeffects on sound accuracy that areparticularly noticeable with violin,trumpet, piano and vocals.Very low inductance values are used inthe LICC, thus providing an excellenttransient response and drasticallyreducing phase shifts between wooferand tweeter. As a result, LICC provideswell-defined natural and open sound -across the entire audio bandwidth.
TAED AMPLIFIER TECHNOLOGYRCF True Active Extended Dynamicamplifier technology is a result of nearlyten years at the forefront of active speakerdesign and manufacture. The result isthe perfect match of amplifier totransducer, RCF is able to achieve thisbecause quite simply we design andmanufacture directly ALL the ingredients.If you are able to increase the effectivedynamic range of a loudspeaker systemthis will immediately provide improvedsonic accuracy, voice clarity, depth andresolution of the audio signals.Our new generation of active amplifiermodules are designed with a new‘’Double Wave’’ Limiting System thatapart from giving improved transducerprotection - guarantees the full use ofthe true dynamic range of the poweramplifier.This in turn dramatically reducesdistortion levels being delivered to thesystems transducers.
DIRECT DRIVE VOICE COIL ASSEMBLYOur voice coil assemblies are designedusing high strength high temperatureNomex® voice coil Formers withrectangular profile copper cladaluminium wire which are assembledusing advanced specially formulatedadhesives. Proprietary curing processesensure optimal assembly strength andsafe operation even under extremethermal conditions. The top of the Formeris bent and bonded directly to the edgeof the titanium diaphragm resulting ina Direct Drive configuration.Direct Drive guarantees optimal transferof energy between the voice coil andthe dome assembly, providing smoother,extended frequency response beyond10 KHz, reducing break up modes andlowering distortion.This assembly delivers high powerhandling along with excellent mechanicaland thermal properties that make RCFPrecision Series compression driversrobust and reliable.
VOICE COILPower Compression is the neglectedfactor in many professional audio systemdesigns.In woofers and subwoofers the powercompression at maximum rated powercan vary from 3-4 dB for good designsand up to 6-7 dB for poorly vented orsmall coil designs. This will affect notonly the final achievable sound pressurelevel (SPL) but also the transducer Thiele-Small parameters, dramatically changingthe high power curve response andsound characteristics.For this reason all our woofer andsubwoofer designs are equipped withlarge sized, properly ventedinside/outside voice coils. Thisguarantees the long term reliability andlife of the product.
INSIDE/OUTSIDE VOICE COILSRCF has developed a unique voice coil,combining the advantages ofinside/outside technology to the superiorquality of polyimide-imide materials (wireresins and former resins).The inside/outside coil offers manyadvantages:- the dissipation surface is doubled- the adhesion area to the former is
doubled- during thermal expansion the former
is squeezed between inside and outsidelayers offering the best mechanicalresistance.
Our former is made from polyimide -imide fibreglass and the area betweenthe coil and the cone is a triple layer ofnomex - fibreglass - nomex for maximumstiffness and accurate sound transfer.
PRODUCT DESCRIPTION ICONS
To improve the understanding of our catalogue and help ourcustomer in easier and immediate choice of the right product, wehave created easy description icons that represent the mainfeatures of our products.
CAR, VAN, TRUCK ICON helps you in understanding sizeand portability of the product.
WATT ICON represents the total amplifier power for activespeakers or power handling for passive speakers.
350W
SPEAKER VISUAL ICON describe the number of way’s andsize of transducers.
BALTIC BIRCH (PP COMPOSITE) ICON describes the cabinetmaterial, Baltic birch or polypropylene composite plastic.
POLE MOUNT ICON represents if the product is polemoun-table or if the subwoofer has a pole cap.
FLYING HARWARE ICON represents if the product offersstandard flying hardware.
1”12”
5
ART was originally conceived way back in 1996. The brief was a tough one. To create perfect sound.Moreover, the speaker enclosures were to be portable, lightweight and strong enough to withstand every day use.Using the latest ‘’Advanced Resource Technology’’.The brief remains the same but with even more exacting challenges. Portable and even lighter in weight systemswere a must, plus the demands from Musicians for improved vocal clarity and definition.
To achieve this RCF has taken the numerous new technological advances in our own transducer developmentsalong with designing new high efficiency ‘’True Active Extended Dynamics’’ TAED amplifier technology. Our new RCFPrecision Series of light in weight Neodymium compression drivers with advanced phase plug technology and highpower ceramic woofers provide this goal.
For natural sound and clarity, nothing comes close - when youcome to audition an ART you will know why we moved heavenand earth to get the perfect sound - so that you can.
The philosophy of ART
7
COMPONENTS
The woofers used in the newArt Series can withstand peak power ofup to 6 times the nominal power. Thesemid bass woofers have been designedfor superior reproduction of acousticsignals up to the crossover frequency.Specific attention has been applied tothe speaker cones, all are optimized forshape and pulp composition.Our edgewound copper clad aluminiumvoice coils provide maximum efficiencyand high speed for accurate transientresponse. ‘’Inside /Outside ’’copper cladaluminium voice coils provide maximumreliability. Our massive magnets offersuperior bass control and mid-bass voicepresence.
Our state of the artcompression drivers are made fromneodymium magnetic circuit technology,reaching levels that exceed 2 Kilogaussin the gap. Thanks to RCF’s “puretitanium” diaphragms and proprietaryhigh pressure oxygen free mouldingtechnology, we are able to reproducetransparent and accurate highfrequencies true in all the audible range.
AMPLIFIERS
All the new ART models aredesigned using newly created RCF ‘TrueActive Extended Dynamics TAED ActiveAmplifier Technology. Based around 350watt low and 50 watt high Bi- Amplifiedmonolithic modules, each amplifier hasa specific input board and is set-up tooptimize the performance in conjunctionto the specific transducers in eachmodel.
Each amplifier will give you:Jack and XLR balanced inputs, XLROutput link, Mic/Line selectable Input,switchable Eq Mode (Voice/Music),Optional Remote Control for Volume,Mute and Equalization.
CABINETS
Art’s polynomial constantdirectivity horn has virtually the samephysical area as the woofer. This meansthat the driver is perceived to achievethe same output power as the low sectionwith minimum diaphragm excursion,resulting in a well defined, natural andopen sound.
The shape of the horn is aunique design able to provide exceptionalconstant directivity with both the 1” and2” compression drivers.Art’s bass reflex cabinet is moulded ina special polypropylene compositematerialresulting from years of experience inplastic cabinet designs, which providesuperior stiffness for the weight andexcellent low frequency damping.
Each cabinet is equipped withergonomically designed handles on eachside and a comfortable top handle foreasy manoeuvrability in every situation.Four M10 threaded inserts are providedfor optional mounting hardware inInstalled Sound Applications.
THE NEXT GENERATION
8
THE NEW ART AMPLIFIER INPUT PANEL
1 MIC AND LINE LEVEL CONTROL
SAFE RECESSED MIC/LINE SWITCH
GREEN-RED-YELLOW EQUALIZATION MODE LED
POWER ON AND LIMITER LEDS
JACK AND FEMALE XLR INPUTS (BAL/UNBAL)MALE XLR SIGNAL OUTPUT
2
3
4
5
WOOFER C. DRIVER POWER DIRECTIVITYPRODUCT
10"
12"
15"
12"
15"
12"
15"
10”
12"
15"
15"
1"
1"
1"
2"
2"
2"
2"
1”
1"
1"
—
350 W
350 W
350 W
400 W
400 W
750 W
750 W
300 W
300 W
300 W
800 W
90 X 70
90 X 60
90 X 60
90 X 60
90 X 60
90 X 60
90 X 60
90 X 70
90 X 60
90 X 60
—
ART 310-A
ART 312-A
ART 315-A
ART 322-A
ART 325-A
ART 522-A
ART 525-A
ART 310
ART 312
ART 315
ART 705-AS
MAX SPL
127 dB
127 dB
128 dB
128 dB
129 dB
130 dB
131 dB
127 dB
127 dB
128 dB
130 dB
9
FEATURES
350 WATT MONOLITHIC BI-AMPLIFICATION,300 WATT LOW FREQUENCY AND 50 WATT HIGHFREQUENCY POWER
127 DB MAX SPL
WIDE DISPERSION, 90 X 70 LOW DISTORTION,CONSTANT DIRECTIVITY HORN
10” NEODYMIUM HIGH POWER WOOFER
1” NEODYMIUM, HIGH FREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASEALIGNMENT, LIMITER AND PROTECTION
MIC/LINE XLR INPUT, XLR SIGNAL OUTPUT
1 COMFORTABLE TOP HANDLE FOR EASYTRANSPORTATION AND POSITIONING
TWO M10 FLY POINTS AND BUILT IN POLEMOUNT ADAPTOR
RCF ART 310-A is an active, wide dispersion2 way sound reinforcement speaker, . It integratesa high power 350 watt amplifier, a completeelectronic processor section and RCF low distortion,high power neodymium transducers. The system isunique in its class for output and vocal intelligibility.
The new 10” neodymium woofer is the resultof the latest refinement in year of RCF experiencein compact 2 way speakers. Features a 2,5 ” voicecoil, very high efficiency and controlled bass
reproduction.The compression driver uses a new 1.5” Mylar
dome design and optimised geometry radial phaseplug. This innovative design is powered from a highflux neodymium magnet offering a very open andnatural midrange sound with extreme precision inhigh frequency reproduction.
A generous 2 step class H design is used topower the low frequencies and the compressiondriver amplifier is a warm and clear class AB design.
ART 310-A is the reference speaker in the 10” size. Incredible amplifier power, highquality neodymium transducers, very compact size cabinet. From live sound, playbackand monitoring to corporate events and presentations, ART 310-A is the ideal speakerin all the situations where the output of a PA and the size of a studio monitor isrequired. Superb deep bass punch, very linear and precise frequency response.
10
350W
1”10”
1m127 dB
2m121 dB
4m115 dB
16m103 dB
32m97 dB
8m109 dB
Incredibly Lightweight
ART 310-A uses high efficiency TAED amplifier and neodymium woofer and compressiondriver for the maximum output in the minimum weight ever seen in the 10” activespeaker.
The input section presents a XLR input connectorthat is switchable from microphone to line levels.A master volume control and a useful XLR loopthrough link guarantee the best versatility.
The processor section includes active crossover,system equalisation, transducers phase alignment,limiter and protection functions. The system isvisually monitored from 4 status LEDs.
All the system is housed in a strong , verylightweight, polypropylene composite enclosure .The woofer is protected from a strong, powdercoated, metal grille.
The cabinet features 2 M10 threaded fly points,a 35 mm stand adaptor plus an ergonomic tophandle for easy transportation.
ERGONOMIC TOP HANDLE FOR EASY TRANSPORTATION1
2 BIG SIZE BASS REFLEX PORTS FOR SUPERB BASS RESPONSE
3 WIDE DISPERSION CONSTANT DIRECTIVITY HORN
5 LOW DISTORTION NEODYMIUM COMPRESSION DRIVER
6 STRONG, LIGHTWEIGHT POLYPROPYLENE ENCLOSURE
7 THICK METAL POWDER COATED GRILLE
6
7
4 HIGH POWER NEODYMIUM WOOFER
11
1m127 dB
2m121 dB
4m115 dB
16m103 dB
32m97 dB
8m109 dB
1”12”
350W
FEATURES
350 WATT MONOLITHIC BI-AMPLIFICATION,300 WATT LOW FREQUENCY AND 50 WATT HIGHFREQUENCY POWER
127 DB MAX SPL
WIDE DISPERSION, 90 X 60 LOW DISTORTION,CONSTANT DIRECTIVITY HORN
12” HIGH POWER WOOFER, 64MM EDGEWOUND ALUMINIUM COIL
1” NEODYMIUM, TITANIUM DOME, HIGHFREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASEALIGNMENT, LIMITER AND PROTECTION
MIC/LINE XLR AND JACK INPUT, XLR SIGNALOUTPUT
2 SIDE HANDLES AND 1 COMFORT DESIGNEDTOP HANDLE FOR EASY TRANSPORTATION ANDPOSITIONING
FOUR M10 FLY POINTS AND BUILT IN POLEMOUNT ADAPTOR
OPTIONAL INFRARED REMOTE CONTROL FORVOLUME, MUTE AND EQ ADJUSTMENT
ART 312-A is the optimum choice for live sound situations where an exceptional fullrange, outstanding bass reproduction and accurate high frequency delivery is required.The ART 312-A is also suitable for monitoring applications.
RCF ART 312-A is an active, wide dispersion2 way sound reinforcement speaker. It integratesa high power 350 Watt amplifier, a completeelectronic processor section and RCF low distortion,high power transducers. The result is a compact,high power accurate system, unique in its class forclarity and low distortion. The new 12” inch woofer is the result of thelatest refinement in years of RCF experience incompact 2 way speakers, resulting in a fast andaccurate reproduction of the midbass frequencyrange and controlled deep bass. The compression driver uses a new 1.5” titanium
dome in front of a low compression, optimisedgeometry and radial phase plug. This innovativedesign is powered from a high flux neodymiummagnet and offers a very open and natural midrangesound and extreme precision in high frequenciesreproduction. A generous 2 step class H design is used topower the low frequencies and the compressiondriver amplifier is a warm and clear class AB design. All components are housed in a strong,lightweight, polypropylene composite enclosure.The cabinet shape is perfect for monitoringapplications.
12
1m128 dB
2m122 dB
4m116 dB
16m104 dB
32m98 dB
8m110 dB
1”15”
350W
FEATURES
350 WATT MONOLITHIC BI-AMPLIFICATION,300 WATT LOW FREQUENCY AND 50 WATT HIGHFREQUENCY POWER
128 DB MAX SPL
WIDE DISPERSION, 90 X 60 LOW DISTORTION,CONSTANT DIRECTIVITY HORN
15” HIGH POWER WOOFER, 64MM EDGEWOUND ALUMINIUM COIL
1” NEODYMIUM, TITANIUM DOME, HIGHFREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASEALIGNMENT, LIMITER AND PROTECTION
MIC/LINE XLR AND JACK INPUT, XLR SIGNALOUTPUT
2 SIDE HANDLES AND 1 COMFORTABLE TOPHANDLE FOR EASY TRANSPORTATION ANDPOSITIONING
FOUR M10 FLY POINTS AND BUILT IN POLEMOUNT ADAPTOR
OPTIONAL INFRARED REMOTE CONTROL FORVOLUME, MUTE AND EQ ADJUSTMENT
ART 315-A is the perfect speaker for live sound situations where you need extra punchin bass reproduction and extremely accurate high frequency response. Thanks to theversatility in both monitoring and playback installation situations representing theideal multipurpose solution.
RCF ART 315-A is an active, wide dispersion 2way sound reinforcement speaker. It integrates ahigh power 350 Watt amplifier, a complete electronicprocessor section and RCF low distortion, highpower transducers. The result is a compact, highpower accurate system, unique in his class forclarity and low distortion. The new 15” inch woofer is the result of thelatest refinement in years of RCF experience incompact 2 way speakers, resulting in an accuratereproduction of the midbass frequency range anda tight punchy bass. The compression driver uses a new 1.5” titanium
dome in front of a low compression, optimisedgeometry, radial phase plug. This innovative designis powered from a high flux neodymium magnetoffering a very open and natural midrange soundwith extreme precision in high frequencyreproduction. A generous 2 step class H design is used topower the low frequencies and the compressiondriver amplifier is a warm and clear class AB design. All components are housed in a strong,lightweight, polypropylene composite enclosure.
13
2”12”
400W
FEATURES
400 WATT MONOLITHIC BI-AMPLIFICATION,350 WATT LOW FREQUENCY AND 50 WATT HIGHFREQUENCY POWER
128 DB MAX SPL
WIDE DISPERSION, 90 X 60 LOW DISTORTION,CONSTANT DIRECTIVITY HORN
12” HIGH POWER WOOFER, 75MMINSIDE/OUTSIDE ALUMINIUM COIL
2” NEODYMIUM, TITANIUM DOME, HIGHFREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASEALIGNMENT, LIMITER AND PROTECTION
MIC/LINE XLR AND JACK INPUT, XLR SIGNALOUTPUT
2 SIDE HANDLES AND 1 ERGONOMIC TOPHANDLE FOR EASY TRANSPORTATION ANDPOSITIONING
FOUR M10 FLY POINTS AND BUILT IN POLEMOUNT ADAPTOR
OPTIONAL INFRARED REMOTE CONTROL FORVOLUME, MUTE AND EQ ADJUSTMENT
With the perfect blend of the fast, high efficiency transducers, ART 322-A offers anextremely linear response and precise, deep low frequency control. The ideal cabinetfor main front of house PA and monitoring, ART 322-A is the perfect solution wherethe power of a 2” compression driver is required for longer throw applications in largervenues. RCF ART 322-A is an active, wide dispersion2 way sound reinforcement speaker. It integratesa high power 400 Watt amplifier, with a completeelectronic processor section and RCF PrecisionSeries low distortion, high power transducers. Theresult is a compact, high power accurate system,incredible for linearity and vocal intelligibility. This new high power 12” inch woofer is theresult of the latest refinement in years of RCFexperience in compact 2 way speakermanufacturing, resulting in a fast and accuratereproduction of the midbass frequency range andtight deep bass. The compression driver uses a 0.05 mm puretitanium dome featuring a complex geometry
suspension and Direct Drive coil. This innovativedesign is powered from a massive high fluxneodymium magnet and an edge wound 64 mmaluminium voice coil. This unique driver offers atransparent midrange sound and extreme fidelityin high frequencies reproduction. A generous 2 step class H TAED amplifierdesign is used to power the low frequencies andthe compression driver amplifier is a warm andclear class AB design. All components are housed in a strong,lightweight, polypropylene composite enclosure.The cabinet shape is perfect for monitoringapplications.
1m128 dB
2m122 dB
4m116 dB
16m104 dB
32m98 dB
8m110 dB
14
1m129 dB
2m123 dB
4m117 dB
16m105 dB
32m99 dB
8m111 dB
FEATURES
400 WATT MONOLITHIC BI-AMPLIFICATION,350 WATT LOW FREQUENCY AND 50 WATT HIGHFREQUENCY POWER
129 DB MAX SPL
WIDE DISPERSION, 90 X 60 LOW DISTORTION,CONSTANT DIRECTIVITY HORN
15” HIGH POWER WOOFER, 75MMINSIDE/OUTSIDE ALUMINIUM COIL
2” NEODYMIUM, TITANIUM DOME RCFPRECISION SERIES HIGH FREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASEALIGNMENT, LIMITER AND PROTECTION
MIC/LINE XLR AND JACK INPUT, XLR SIGNALOUTPUT
2 SIDE HANDLES AND 1 ERGONOMIC TOPHANDLE FOR EASY TRANSPORTATION ANDPOSITIONING
FOUR M10 FLY POINTS AND BUILT IN POLEMOUNT ADAPTOR
OPTIONAL INFRARED REMOTE CONTROL FORVOLUME, MUTE AND EQ ADJUSTMENT
ART 325-A is the reference speaker in the new ART series. Ideal in live sound andinstalled situations, it is remarkable for deep bass punch, clean midrange output andaccurate high frequencies. Offering the ultimate intelligibility in vocal and RecordedMusic, from live sound to playback, from monitoring to fixed installation applications.
RCF ART 325-A is an active, wide dispersion2 way sound reinforcement speaker. It integratesa high power 400 Watt amplifier, a completeelectronic processor section and RCF PrecisionSeries low distortion, high power transducer. Theresult is a compact, high power accurate system,unique in its class for linearity and low distortion. This new high power 15” inch woofer is theresult of the latest refinement in years of RCFexperience in compact 2 way speakermanufacturing, providing a fast and accuratereproduction of the midbass frequency range andtight punchy bass.
The compression driver uses a 0.05 mm puretitanium dome featuring a complex geometrysuspension and Direct Drive coil. This innovativedesign is powered from a massive high fluxneodymium magnet and an edge wound 64 mmaluminium voice coil. This unique driver offers atransparent midrange sound and an extreme fidelityin high frequency reproduction. A generous 2 step class H TAED design is usedto power the low frequencies and the compressiondriver amplifier is a warm and clear class AB design. All components are housed in a strong,lightweight, polypropylene composite enclosure.
2”15”
400W
15
750 WATT DIGITAL AMPLIFIER,500 WATT LOW FREQUENCY AND 250 WATTHIGH FREQUENCY POWER
130 DB MAX SPL
WIDE DISPERSION, 90 X 60 LOW DISTORTION,CONSTANT DIRECTIVITY HORN
12” NEODYMIUM, HIGH EFFICIENCY WOOFER,75MM IN-OUT VOICE COIL
2” NEODYMIUM, TITANIUM DOME, 64 MMVOICE COIL, HIGH FREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASEALIGNMENT, LIMITER AND PROTECTION
LINE JACK/XLR INPUT, XLR SIGNAL OUTPUT
2 SIDE HANDLES, 1 TOP HANDLE FOR EASYTRANSPORTATION AND POSITIONING
FOUR M10 FLY POINTS AND POLE MOUNTADAPTOR
ART 522-A FEATURES
ART 522-A and ART 525-A are a milestone in ART series evolution. The careful acousticdesign, no compromise neodymium transducers and a powerful digital amplifier makethe newest ART models the preferred tool of many professionals.Incredibly lightweight, are perfect in live sound reinforcement and reliable in installedsituations.
RCF ART 522-A and ART 525-A are 2 way activesystems offering substantial power for a variety ofprofessional applications that include primarysound reinforcement and supplementary fill forlarger systems.
They integrates a digital high power 750 Wattamplifier, a complete electronic processorsection and premium RCF low distortion, high powertransducers.
The result is compact, light weight, high poweraccurate systems, unique in there class for clarityand low distortion.
The total amplifier power is 750 watt: a 500watt digital amplifier design is used to power thelow frequencies, the compression driver is poweredfrom 250 watt of digital clear power.
The input section offers an jack/XLR inputcombo connector, a master volume control and auseful XLR loop-through link guarantee the bestversatility.
The processor section includes low noise activecrossover, system equalization, transducer phasealignment, limiter and protection functions.
1m130 dB
2m124 dB
4m118 dB
16m106 dB
32m100 dB
8m112 dB
ART 522-A
DIGITAL POWER
16
DIGITAL POWER
ART 525-A
ART 525-A FEATURES
750 WATT DIGITAL AMPLIFIER,500 WATT LOW FREQUENCY AND 250 WATTHIGH FREQUENCY POWER
131 DB MAX SPL
WIDE DISPERSION, 90 X 60 LOW DISTORTION,CONSTANT DIRECTIVITY HORN
15” NEODYMIUM, HIGH EFFICIENCY WOOFER,87 MM IN-OUT VOICE COIL
2” NEO, TITANIUM DOME, 64 MM VOICE COIL,HIGH FREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASEALIGNMENT, LIMITER AND PROTECTION
LINE JACK/XLR INPUT, XLR SIGNAL OUTPUT
2 SIDE HANDLES, 1 TOP HANDLE FOR EASYTRANSPORTATION AND POSITIONING
FOUR M10 FLY POINTS AND POLE MOUNTADAPTOR
The compression driver uses a 0.05 mmtitanium dome featuring a vented suspension andis powered from a massive high flux neodymiummagnet and an edge wound 64 mm aluminiumvoice coil. This top class driver offers a high output,transparent midrange sound and clarity in highfrequencies reproduction.
The ART 522-A features a 12” inch woofer that,with a 3” inside-outside aluminium coil and apowerful magnetic structure, guarantees a fast andaccurate mid-bass frequency range.
The ART 525-A features a 15” inch woofer that,
thanks to its 3.5” inside-outside aluminium coiland a powerful magnetic structure guarantees apowerful bass reproduction.
All components are housed in a rigidpolypropylene composite enclosure. The woofer isprotected by a powder coated, metal grille. Thecabinet features four M10 threaded fly points, a35 mm pole mount adaptor, two side handles anda top handle.
2”15”
750W
1m131 dB
2m125 dB
4m119 dB
16m107 dB
32m101 dB
8m113 dB
ART 522A ON TOP OF4PRO 8001-AS SUBWOOFER
2”12”
750W
17
The ART 705-AS is an extremely compact high output active subwoofer system.RCF’s Research and Development engineers have developed a totally new “High CurrentCapacity” Monolithic amplifier alongside a totally new RCF 15” high power woofer.
RCF ART 705-AS active subwoofer integratesa high current 800 Watt amplifier, a completeelectronic processor section and RCF low distortion,high power woofer. The result is a compact, highpower system, unique in its class for output andlow distortion. This new high power 15” inch woofer is theresult of the latest refinement in years of RCFexperience in compact active subwoofers designand manufacture, resulting in a fast and controlledreproduction of the bass frequency range. Featuresa 3” inside/outside voice coil to minimize powercompression extending the life of this product. The input section presents mono/stereo combo
XLR/Jack input connectors and XLR high passoutput connectors. A recessed master volume, thephase switch and the selectable crossover frequencyswitch guarantee outstanding versatility. Theprocessor section includes active systemequalization, limiter and protection functions. Thesystem is visually monitored from 4 status LEDs. The Baltic birch plywood enclosure is paintedwith black, heavy duty, textured epoxy. The front isprotected from a strong, powder coated, metalgrille. The cabinet features two M10 threaded pointsfor optional speaker kart, a 35 mm pole mountsocket, two ergonomic side handles.
FEATURES
HIGH CURRENT 800 WATT CLASS H AMPLIFIER
130 DB MAX SPL
15” HIGH POWER WOOFER, 75MMINSIDE/OUTSIDE COPPER COIL
RESPONSE DOWN TO 40 HZ
SELECTABLE CROSSOVER AND HIGH PASSOUTPUTS, PHASE SWITCH
ELECTRONIC EQUALIZATION, LIMITER ANDPROTECTION
MONO/STEREO COMBO XLR/JACK INPUT,MONO/STEREO XLR SIGNAL OUTPUT
BALTIC BIRCH COMPACT ENCLOSURE AND 2SIDE HANDLES FOR EASY TRANSPORTATION
BUILT IN POLE MOUNT, TWO M10 POINTS FOROPTIONAL SPEAKER KART
18
COMBO JACK/XLR FEMALE INPUT CONNECTORS (BAL/UNBAL)1
2 MALE XLR OUTPUT LINK CONNECTORS
3 MALE XLR STEREO CROSSOVER OUTPUTS
5 RECESSED PHASE CONTROL SWITCH
6 SELECTABLE CROSSOVER NETWORK CONTROL SWITCH
7 4 SYSTEM STATUS LEDS
15800W
1m130 dB
2m124 dB
4m118 dB
16m106 dB
32m100 dB
8m112 dB
The ART 705-AS is an extremely compact highoutput active subwoofer system. RCF’s Researchand Development engineers have developed atotally new “High Current Capacity” Monolithicamplifier alongside a totally new RCF 15” highpower woofer. The ART 705-AS delivers tight, fast controlledbass response at very high efficiency levels. Offeringincreased dynamic range. The system re-definesaudio subwoofer performance standards. RCF engineers have developed a new HighCurrent 800 watt class H two step ultra efficienttopology amplifier to provide the critical performancedemanded by True Active Subwoofers. The ART 705-AS’s woofer technology is usingnew RCF woofer design parameters. We have utilisedhigh temperature polyimide voice coil assemblieswith state of the art curing processes plus advancedmagnetic structures and efficient cooling systems.
The RCF Precision ‘’Inside/ Outside’’ voice coilsassure long term reliability and vastly reducedpower compression.
Applications include:- Small to medium-sized Live and Playback- Portable PA Systems for Speech and Multimedia- Mobile DJ- Fixed Installations
The ART 705-AS is designed to compliment allART Active and Passive models. It can also be usedas an “add –on” to any existing active or passivePA Speaker System.
ART 705AS INPUT PANEL 6
7
4 RECESSED LINE LEVEL CONTROL
19
RCF ART 310 is an wide dispersion 2 waysound reinforcement speaker. The new 10”neodymium woofer is the result of the latestrefinement in year of RCF experience in compact2 way speakers. Features a 2,5 ” voice coil, veryhigh efficiency and controlled bass reproduction.
The compression driver uses a new 1.5” Mylardome design and optimised geometry radial phaseplug. This innovative design is powered from a highflux neodymium magnet offering a very open and
natural midrange sound with extreme precision inhigh frequency reproduction.
All the system is housed in a strong , verylightweight, polypropylene composite enclosure .The components are protected from a strong,powder coated, metal grille. The cabinet features2 M10 threaded fly points, a 35 mm stand adaptorplus an ergonomic top handle for easytransportation.
FEATURES
300 WATT POWER HANDLING
127 DB MAX SPL
WIDE DISPERSION, 90°X70° LOW DISTORTION,CONSTANT DIRECTIVITY HORN
10” HIGH POWER WOOFER, 64MM IN/OUTALUMINIUM COIL
1” NEODYMIUM, HIGH FREQUENCY DRIVER
2 X NL4 SPEAKON® CONNECTOR
1 COMFORTABLE TOP HANDLE FOR EASYTRANSPORTATION AND POSITIONING
TWO M10 FLY POINTS AND BUILT IN POLEMOUNT ADAPTOR
ART 310 is the reference speaker in the 10” size. High quality neodymium transducers,very compact size cabinet. From live sound, playback and monitoring to corporateevents and presentations, ART 310 is the ideal speaker in all the situations wherethe output of a PA and the size of a studio monitor is required. Superb deep basspunch, very linear and precise frequency response.
1”10”
300W
1m127 dB
2m121 dB
4m115 dB
16m103 dB
32m97 dB
8m109 dB
20
RCF ART 312 and RCF ART 315 are a widedispersion, 2 way sound reinforcement speakers.Integrates a high power LICC high level crossovernetwork and RCF low distortion, high powertransducers. The new 12” and 15” woofer are the result ofthe latest refinement in years of RCF experience incompact 2 way speaker manufacturing, resultingin an accurate reproduction of the midbassfrequency range and a tight punchy bass. The compression driver uses a new 1.5” titaniumdome in front of a low compression, optimisedgeometry, radial phase plug. This innovative design
is powered from a high flux neodymium magnetand offers a very open and natural midrange soundand extreme precision in high frequencyreproduction. Our LICC low impedance compensated crossovernetwork featuring lower (than conventional) inductionvalue in series with the woofer offer delay reduction,reduced phase shift and superior transient response.The compression driver is protected by a fastdynamic electronic circuit. The input section presents 2 x NL4 Speakon®connectors offering an easy loop-through link.
ART 315 and ART 312, ideal for live sound situations, offer the same careful acousticdesign and innovative transducers used in the active series. With very good punchin bass reproduction and extremely accurate high frequencies, ART 315 and ART 312are the perfect solution for playback and installation situations where an externalamplifier is required.
ART 312/315 FEATURES
300 WATT POWER HANDLING
127/128 DB MAX SPL
WIDE DISPERSION, 90 X 60 LOW DISTORTION,CONSTANT DIRECTIVITY HORN
12/15” HIGH POWER WOOFER, 64MM EDGEWOUND ALUMINIUM COIL
1” NEODYMIUM, TITANIUM DOME, HIGHFREQUENCY DRIVER
LICC LOW IMPEDANCE COMPENSATEDCROSSOVER, ELECTRONIC DRIVER PROTECTION
2 X NL4 SPEAKON® CONNECTOR
2 SIDE HANDLES AND 1 ERGONOMIC TOPHANDLE FOR EASY TRANSPORTATION ANDPOSITIONING
FOUR M10 FLY POINTS AND POLE MOUNTADAPTOR
1m127 dB128 dB
2m121 dB122 dB
4m115 dB116 dB
16m103 dB104 dB
32m97 dB98 dB
8m109 dB110 dB
ART315
ART 312 / 315300W
1”12”
ART312
300W
1”15”
21
Plug your favourite microphone into any 4PRO Systemand immediately experience the accurate voicing.
If you have had the opportunity to listen to any of our active systems live in the past, then you will, hopefullybe enthusiastic about our new 4PRO Series. The system represents a natural evolution of what RCF has producedin the past. This progression has now reached the 4PRO system, dedicated to live, touring and fixed installations.As with all of our developments, it comes out of a desire to improve on what has gone before. In doing so, wefirst listened to what our customers said, it is from their feedback, that we have striven to produce the perfectspeaker.
Over the past years, of continuous research and development of active technology, RCF have reached awhole new audience in the live PA and concert market. In doing so, one thing has become evident, in both largeand small live music venues, with their professionalism there is a passion to produce something more – the soundthat gives you the possibility of creating new emotions.
Active speaker technology is a cost effective solution when produced correctly. It is only by the checkingof every single transducer, signal processor that is used in the speakers, plus Real time control circuits that takecare of the audio chain and status of the electronics, monitoring the temperatures of heat sinks that you arriveat designing the most reliable and acoustically correct active designs. RCF is not only a pioneer in this field buta true market leader.
4PRO is designed for professionals, who have always loved RCF speakers and have looked for the perfectmarriage of specific power amplifiers with the appropriate crossover or active processor.
23
AMPLIFIERS
All the 4PRO models aredesigned using newly created RCF ‘TrueActive Extended Dynamics ‘TAED’ ActiveAmplifier Technology.
Each amplifier has a specificinput board and set-up to optimise theperformance in conjunction to thespecific transducers in each model.
Each amplifier will give you:combo Jack/XLR balanced inputs, XLROutput link, protected gain control,Powercon® Mains Input.
Each subwoofer amplifier isequipped with mono/stereo inputs,protected gain control, low pass filters,mono/stereo crossover outputs,crossover frequency selection switch andphase control switch.
EXPERIENCE
COMPONENTS
It is the acoustic designs thathave made RCF the transducer companyof choice for many of the world’s leadingprofessional audio brands. For the designof 4PRO, we have not only used all newhigh frequency drivers which are part ofour high performance RCF and the wellknown RCF 18” woofer, but after 2 yearsof research, we have finally produced anew “state of the art” midrange unit.
The compression driver is thevery latest in neodymium magnetic circuittechnology, reaching levels that exceed2 Kilogauss in the gap. The “puretitanium” diaphragms are able toreproduce transparent and accurate highfrequencies, true to all the audio range.This is thanks to RCF’s proprietary highpressure oxygen free mouldingtechnology.
The low frequency drivers usedin the 4PRO Series can withstand peakpower of up to 6 times the nominalpower. These mid bass woofers havebeen designed for superior reproductionof acoustic signals up to the crossoverfrequency.
CABINETS
All 4PRO cabinets are in Balticbirch, heavy duty painted.
4PRO 3001-A and 4PRO4001-A cabinets sides are coated with“ultra strong vinyl”, top and bottomplates are moulded in high densitycompact polystyrene. The other modelsutilise a road tough textured black epoxypaint finish.
All models are equipped withflying hardware (3 M10 threaded pointsand flanges), 4PRO 6001-A offer 3proprietary FlyTrak points for rapidinstallation.
24
THE NEW 4PRO THREE WAY INPUT PANEL
1
2
3
4
WOOFER MIDRANGE POWER DIRECTIVITYPRODUCT
15"
12"
15"
2 x 12"
2 x 15"
18"
18"
—
2 x 15"
18"
—
—
6"
8"
10"
—
—
10"
—
—
400 W
400 W
800 W
950 W
950 W
800 W
800 W
400 W
1600 W
1000 W
80 X 60
40 X 60
90 X 45
80 X 60
60 X 40
—
—
60 X 40
—
—
4PRO 3001-A
4PRO 3002-SMA
4PRO 4001-A
4PRO 6001-A
4PRO 7001-A
4PRO 8001-AS
4PRO 8002-AS
4PRO 7001 MHP
4PRO 7001 BP
4PRO 8001-S
MAX SPL
130 dB
130 dB
130 dB
134 dB
138 dB
133 dB
134 dB
139 dB
139 dB
133 dB
COMBO JACK/XLR FEMALE INPUTCONNECTORS (BAL/UNBAL)
MALE XLR OUTPUT LINK CONNECTORS
RECESSED LINE LEVEL CONTROL
4 SYSTEM STATUS LEDS
C. DRIVER
1"
2"
1"
1"
2"
—
—
3"
—
—
25
FEATURES
400 WATT MONOLITHIC BI-AMPLIFICATION, 350WATT LOW FREQUENCY AND 50 WATT HIGHFREQUENCY POWER
130 DB MAX SPL
WIDE DISPERSION, 80 X 60 LOW DISTORTION,CONSTANT DIRECTIVITY HORN
15” HIGH POWER WOOFER, 64MM EDGE WOUNDALUMINIUM COIL
1” NEODYMIUM, TITANIUM DOME, HIGHFREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASE ALIGNMENT,LIMITER AND PROTECTION
MIC/LINE XLR AND JACK INPUT, XLR SIGNAL OUTPUT
BALTIC BIRCH CABINET WITH 2 SIDE HANDLESFOR EASY TRANSPORTATION AND POSITIONING
THREE M10 FLY POINTS AND STAND SOCKET
OPTIONAL REMOTE CONTROL
1m130 dB
2m124 dB
4m118 dB
16m106 dB
32m100 dB
8m112 dB
1”15”
400W
RCF 4PRO 3001-A is an active, wide dispersion2 way sound reinforcement speaker. It integratesa high power 350 Watt amplifier, with completeelectronic processor section and RCF low distortion,high power transducers. The result is a robust, highefficiency accurate system, producing unparalledclarity and transparency for 15” and 1” 2 wayspeakers. The new 15” inch woofer is the result of thelatest refinement in years of RCF experience incompact 2 way speaker applications, resulting inan accurate reproduction of the midbass frequencyrange and a tight extended bass.
The compression driver uses a new 1.5” titaniumdome in front of a low compression, optimisedgeometry, radial phase plug. A generous 2 step class H design is used topower the low frequencies and the compressiondriver amplifier is a warm and clear class AB design. All components are housed in a strong Balticbirch plywood enclosure where high densitypolystyrene end caps guarantee the maximumstrength. Woofer and horn are protected from a fullfront, strong, powder coated, metal grille. The cabinetfeatures three M10 threaded fly points, a 35 mmstand adaptor, two side handles for easy portability.
4PRO 3001-A is the perfect 2 way speaker for professional live sound situations wherelinearity in reproduction and extremely accurate high frequencies are required. Thanksto the versatility in live, playback and installation situations the 4PRO 3001-A representsthe perfect multipurpose solution.
26
FEATURES
400 WATT MONOLITHIC BI-AMPLIFICATION. 350WATT LOW FREQUENCY AND 50 WATT HIGHFREQUENCY POWER.
130 DB MAX SPL
CONTROLLED DISPERTION, 40 X 60 LOWDISTORTION, MID-HIGH HORN ASSEMBLY
12” HIGH POWER NEODYMIUM WOOFER, 75MMINSIDE/OUTSIDE ALUMINIUM COIL
2” NEODYMIUM, TITANIUM DOME, HIGHFREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASE ALIGNMENT,LIMITER AND PROTECTION
LINE COMBO XLR/JACK INPUT, XLR SIGNAL OUTPUT
BALTIC BIRCH CABINET WITH 1 SIDE HANDLESFOR EASY TRANSPORTATION AND POSITIONING
OPTIONAL REMOTE CONTROL
1m130 dB
2m124 dB
4m118 dB
16m106 dB
32m100 dB
8m112 dB
400W
2”12”
RCF 4PRO 3002-SMA is an active, controlleddispersion 2 way symmetric stage monitor. Itintegrates a high power 400 watt amplifier, acomplete electronic processor section and RCFlow distortion, high power neodymium transducers.
The system is unique in its class for outputand vocal intelligibility. The symmetric transducersconfiguration guarantee the sound coherencybetween left and right side of the speaker.
The new 12” neodymium woofer is the resultof the latest refinement in year of RCF experiencein compact speakers. Features a 3 ” voice coil, amassive outside ring neodymium magnet, veryhigh efficiency and controlled mid-bassreproduction.
The compression driver uses a new 2.5” puretitanium dome featuring a complex geometrysuspension and Direct Drive Coil.
4PRO 3002-SMA is designed with a specific goal: build a high power, professionalactive stage monitor with symmetric transducers configuration maintaining the lowestpossible profile and weight.The result is a first class stage monitor with incredible amplifier power, high qualityneodymium transducers, very compact size cabinet. The voice is accurate and deep,the sound transparent in the mids and extremely accurate at very high frequencies.The 40x60 horn provides a smooth and even coverage for the performer and a verylow side emission. Very good feedback immunity.
27
1”6”15”
800W
FEATURES
800 WATT MONOLITHIC TRI-AMPLIFICATION. 600WATT LOW FREQUENCY, 150 WATT MIDRANGEFREQUENCY AND 50 WATT HIGH FREQUENCYPOWER.
130 DB MAX SPL
WIDE DISPERSION, 90 X 45 LOW DISTORTION,MID-HIGH HORN ASSEMBLY
15” HIGH POWER WOOFER, 75MMINSIDE/OUTSIDE ALUMINIUM COIL
6” HIGH EFFICIENCY, LOW DISTORTION, HORNLOADED MIDRANGE
1” NEODYMIUM, TITANIUM DOME, HIGHFREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASE ALIGNMENT,LIMITER AND PROTECTION
LINE COMBO XLR/JACK INPUT, XLR SIGNALOUTPUT
BALTIC BIRCH CABINET WITH 2 SIDE HANDLESFOR EASY TRANSPORTATION AND POSITIONING
THREE M10 FLY POINTS
RCF 4PRO 4001-A is an active, wide dispersion3 way sound reinforcement speaker. It integratesa massive 800 Watt amplifier, a complete electronicprocessor section and RCF low distortion, highpower transducers. The system is compact andextremely linear and offers the typical balancedsound of high level three way systems. RCF’s unique 6” cone midrange is built in andoptimised for the 4PRO 4001-A horn assembly.Specific attention has been dedicated to lowdistortion and dynamic properties of this transducer. The compression driver uses a new 1.5” titaniumdome in front of a low compression, optimised
geometry, radial phase plug. A high current 2 step class H design is usedto power the low frequencies.Mid and highfrequencies are separately powered from class ABdedicated low distortion designs. All components are housed in a strong Balticbirch plywood enclosure where high densitypolystyrene end caps guarantee the maximumstrength. The woofer and mid-high horn is protectedfrom a full front, strong, powder coated, metal grille.The cabinet features three M10 threaded fly pointsand two side handles for easy portability.
4PRO 4001-A is a high power 3 way speaker that provide a full solution for live sound,playback and installation situations. The extreme linearity and accuracy in reproductionmake 4PRO 4001-A the first choice speaker in its class. Ideal for Main PA, Side Fills,Night Clubs and Corporate Events.
1m130 dB
2m124 dB
4m118 dB
16m106 dB
32m100 dB
8m112 dB
28
1m134 dB
2m128 dB
4m122 dB
16m110 dB
32m104 dB
8m116 dB
1”8”
2x12”
FEATURES
950 WATT MONOLITHIC TRI-AMPLIFICATION, 600WATT LOW FREQUENCY, 300 WATT MIDRANGEFREQUENCY AND 50 WATT HIGH FREQUENCYPOWER.
134 DB MAX SPL
WIDE DISPERSION, 80 X 60 LOW DISTORTION,MIDRANGE AND HIGH FREQUENCY HORNS
2 X 12” HIGH POWER NEODYMIUM WOOFERS,75MM INSIDE/OUTSIDE ALUMINIUM COIL
8” HIGH EFFICIENCY, LOW DISTORTION,NEODYMIUM HORN LOADED MIDRANGE
1” NEODYMIUM, TITANIUM DOME, HIGHFREQUENCY DRIVER
ELECTRONIC EQUALIZATION, PHASE ALIGNMENT,LIMITER AND PROTECTION
LINE COMBO XLR/JACK INPUT, XLR SIGNALOUTPUT
BALTIC BIRCH CABINET WITH 2 SIDE HANDLESAND 1 ERGONOMIC TOP HANDLE FOR EASYTRANSPORTATION AND POSITIONING
FIVE 3 POSITION FLY-TRACKS POINTS AND TWOM10 POINTS FOR REAR KART
RCF 4PRO 6001-A is an active, medium throw,3 way sound reinforcement speaker. It integratesa massive power 950 Watt amplifier, a completeelectronic processor section and “full neodymium”RCF low distortion, high power transducers. RCF’s unique 8” RCF Precision Series sealedbasket midrange is specifically optimised to workin conjunction with the 4PRO 6001-A midrangehorn. A massive neodymium magnet and a“compression driver level” assembly design hasbeen dedicated to reach low distortion and dynamicproperties for this transducer. The compression driver uses a new 1.75” puretitanium dome in front of a low compression,
optimised geometry, 3 slot phase plug. Thisinnovative design is powered from an extremelyhigh flux neodymium magnet and offers incredibleprecision in high frequency reproduction. A high current 2 step class H design is usedto power the low frequencies, mid and highfrequencies are separately powered from class ABdedicated low distortion designs. All components are housed in a trapezoidal,strong Baltic birch plywood enclosure. The cabinetfeatures three 3 position fly-tracks and 2 M10threaded points for rear kart. Two recessed sidehandles and one top handle guarantees easyportability.
4PRO 6001-A is a high output, medium throw, 3 way speaker designed for highdemanding professional live sound systems. The incredible output and the extremelinearity and accuracy in reproduction make 4PRO 6001-A - a clear reference in itsclass. Perfect for Main PA, Side Fills, Night Clubs and Corporate Events
950W
29
1m138 dB
2m132 dB
4m126 dB
16m114 dB
32m108 dB
8m120 dB
4PRO 7001-A is a leading edge system fortouring and professional applications . It is anarrayable, active, medium throw system thatintegrates a massive power 950 Watt amplifier, acomplete electronic processor section and “fullneodymium” RCF low distortion, high powertransducers.
The new 15” inch mid-bass are the result ofthe latest refinement in years of RCF experience inspeaker design and manufacture, resulting in anaccurate and a tight bass response. RCF’s unique10” Precision sealed basket midrange is speciallyoptimised to work with the 4PRO-7001-A 60x40midrange horn. A massive neodymium magnet and
a “Compression Driver level” assembly design hasbeen dedicated to reach low distortion and dynamicproperties for this transducer. The compressiondriver uses a new 2.5” titanium dome in front ofa low compression, optimised geometry, aluminumphase plug. This innovative design is powered froma high flux neodymium magnet and offers a veryopen and natural sound and an extreme precisionin high frequency reproduction. The driver is loadedon a 60x40 constant directivity aluminum horn. Ahigh current 2 step class H design is used to powerthe low frequencies. Mid and high frequencies areseparately powered from class AB dedicated lowdistortion designs.
FEATURES
950 WATT MONOLITHIC TRI-AMPLIFICATION.600 WATT LOW FREQUENCY, 300 WATTMIDRANGE FREQUENCY AND 50 WATT HIGHFREQUENCY POWER.
138 DB MAX SPL
CONTROLLED DISPERSION, 60 X 40 LOWDISTORTION, MID-HIGH HORNS
2 X 15” NEODYMIUM HIGH POWER MID-BASS,75MM INSIDE/OUTSIDE ALUMINIUM COIL
10” NEODYMIUM HIGH EFFICIENCY, LOWDISTORTION, SEALED BASKET, HORN LOADEDMIDRANGE
2” NEODYMIUM, TITANIUM DOME, HIGHFREQUENCY DRIVER, ALUMINIUM HORN
ELECTRONIC EQUALIZATION, PHASE ALIGNMENT,LIMITER AND PROTECTION
LINE COMBO XLR/JACK INPUT, XLR SIGNALOUTPUT
BASS DELAY INSERT, MID-HIGH PHASE SWITCH,ARRAY EQUALISATIONS
BALTIC BIRCH CABINETS WITH ALUMINUMHANDLES FOR EASY TRANSPORTATION ANDPOSITIONING
9 M10 FLY POINTS 7001A-MH, 8 M10 FLY POINTS7001A-BA
4PRO 7001-A is powerful and precise in concert sound applications and equallyimpressive in professional sound systems such as large clubs and theatres.Any element of the system is pushed well below its limit and the final result is aremarkably clean and transparent sound, with the lowest distortion, an increasedoverall output and an exceptionally smooth frequency response. Specially engineeredfor touring applications
4PRO 7001-MH
950W
2”10”
2x15”
30
The very unique input section presents acombo XLR/Jack line input connector, a recessedmaster volume and a useful XLR loop-through link.Extra features are the Bass external time delayin/out, the “3-position” array equalisation, the mid-high phase switch.
The processor section includes active crossover,system equalization, transducer phase alignment,limiter and protection functions. The system isvisually monitored from 4 status LEDs.
4PRO-7001 MH is the two way mid-high systemin a trapezoidal enclosure for easy array applications4PRO-7001 is the active mid-bass section, including2 x 15” high power neodymium mid-bass and thepowered electronic. The two 15” are loaded inpass-band high efficiency configuration .
All components are housed in a strong Balticbirch plywood enclosures. The cabinets featuresM10 threaded fly points and 8 each 3-positionfly-tracks. Two side handles for easy portability forthe MH and 4 side handles for the BA.
COMBO JACK/XLR FEMALE INPUT/OUTPUT CONNECTORS (BAL/UNBAL)1
2 XLR IN/OUT MB SECTION TIME DELAY INSERT
3 MH SECTION SPEAKON OUTPUT
5 RECESSED MH SECTION PHASE CONTROL SWITCH
6 SELECTABLE EQUALISATION NETWORK CONTROL SWITCH
7 4 SYSTEM STATUS LEDS
6
7
4PRO 7001-BA
4 RECESSED LINE LEVEL CONTROL
31
RCF 4PRO 8001-AS active subwoofer integratesan high current 800 Watt amplifier, a completeelectronic processor section and premium RCF lowdistortion, high power woofer. The result is a compact,high power subwoofer, unique in his class forextended output and low distortion. This new high power 18” inch woofer is theresult of the latest refinement in years of RCFexperience in compact active subwoofer designand manufacture, providing a fast and controlledreproduction of the bass frequency range. A 2 step class H design is used to power thesystem. This high current design controls the amount
of deliverable power in conjunction with a massivetransformer and a multiple of high storage capacitorsit is able to achieve perfect control of the woofermass at very high output levels. The input section offers mono/stereo comboXLR/Jack input connectors and XLR high passoutput connectors. A recessed master volume, thephase switch and the selectable crossover frequencyswitch guarantee the best versatility. The cabinet features two M10 threaded pointsfor optional speaker kart, a 35 mm pole mountsocket, two comfortable recessed side handles.
FEATURES
HIGH CURRENT 800 WATT CLASS H AMPLIFIER
133 DB MAX SPL
18” HIGH POWER WOOFER, 100 MMINSIDE/OUTSIDE COPPER COIL
RESPONSE DOWN TO 40 HZ
SELECTABLE CROSSOVER AND HIGH PASSOUTPUTS, PHASE SWITCH
ELECTRONIC EQUALIZATION, LIMITER ANDPROTECTION
MONO/STEREO COMBO XLR/JACK INPUT,MONO/STEREO XLR SIGNAL OUTPUT
BALTIC BIRCH COMPACT ENCLOSURE AND 2 SIDEHANDLES FOR EASY TRANSPORTATION
BUILT IN POLE MOUNT, TWO M10 POINTS FOROPTIONAL SPEAKER KART
4PRO 8001-AS is an active, high output, bass reflex subwoofer system. Featuring anRCF 18” newly designed high power woofer in combination with 800 Watt Monolithicamplifier. The ideal complement for 4PRO Series and ART series speakers. Perfectwhen you need to increase the system headroom and you look for extended bassfrequency response; it is the ideal complement for existing active or passive PA.Applications include Main PA, Side Fills, Night Clubs and Corporate Events.
1m133 dB
2m127 dB
4m121 dB
16m109 dB
32m103 dB
8m115 dB
800W 18
32
FEATURES
HIGH CURRENT 800 WATT CLASS H AMPLIFIER
134 DB MAX SPL
18” HIGH POWER RCF WOOFER, 100 MMINSIDE/OUTSIDE COPPER COIL
RESPONSE DOWN TO 40 HZ
SELECTABLE CROSSOVER AND HIGH PASSOUTPUTS, PHASE SWITCH
ELECTRONIC EQUALIZATION, LIMITER ANDPROTECTION
MONO/STEREO COMBO XLR/JACK INPUT,MONO/STEREO XLR SIGNAL OUTPUT
BALTIC BIRCH COMPACT ENCLOSURE AND 2SIDE HANDLES FOR EASY TRANSPORTATION
BUILT IN POLE MOUNT, TWO M10 POINTS FOROPTIONAL SPEAKER KART
4PRO 8002-AS is an active, high output, bandpass subwoofer system. Featuring an18” newly designed RCF high power woofer in combination with 800 Watt Monolithicamplifiers. The 4PRO 8002-AS is the ideal complement for 4PRO Series and ART seriesspeakers. Perfect when you need to increase the system headroom and you look forpowerful punchy bass response; it is the ideal complement for existing active orpassive PA. Applications include Main PA, Side Fills, Night Clubs and Corporate Events.
1m134 dB
2m128 dB
4m122 dB
16m110 dB
32m104 dB
8m116 dB
800W 18
33
RCF 4PRO 8002-AS active subwoofer integratesa high current 800 Watt amplifier, plus completeelectronic processor section and RCF PrecisionSeries low distortion, high power woofer. The resultis a compact, high power subwoofer, unique in itsclass for punchy output and low distortioncharacteristics. This new high power 18” inch woofer is theresult of the last refinement in years of RCFexperience in compact active subwoofers design,resulting in a fast and controlled reproduction ofthe bass frequency range. A 2 step class H design is used to power thesystem. This high current design, the amount of
deliverable power in conjunction with a massivetransformer and a multiple of high storage capacitorsis able to achieve perfect control of the woofermass at very high output levels. The input section presents mono/stereo comboXLR/Jack input connectors and XLR high passoutput connectors. A recessed master volume, thephase switch and the selectable crossover frequencyswitch guarantee the best versatility. The cabinet features two M10 threaded pointsfor optional speaker kart, a 35 mm polemountadaptor, two ergonomic recessed sidehandles.
4PRO 7001 is unique in concert sound applications for SPL and dynamics and equallyimpressive in professional sound systems such as large clubs and theatres.Specially engineered for touring applications and Larger Venue Installations.
4PRO 7001 is a leading edge system for touringand professional applications . It is an arrayable,medium throw system that integrates very highpower “full neodymium” RCF low distortiontransducers. The new 15” inch neodymium, 4” voice coilmid-bass are the result of the latest refinement inyears of RCF experience in speaker design andmanufacture, resulting in an accurate and a tightbass response. RCF’s unique 10” Precision sealed basketmidrange is specially optimized to work with the4PRO-7001 60x40 midrange horn. A massiveneodymium magnet and a “Compression Driverlevel” assembly design has been dedicated to reach
low distortion and dynamic properties for thistransducer. The compression driver is our “reference model”,using a new 3” titanium dome in front of a lowcompression, optimized geometry, aluminum phaseplug. This innovative design is powered from a highflux neodymium magnet and offers a very openand natural sound and an extreme precision inhigh frequency reproduction. The driver is loadedon a 60x40 constant directivity aluminum horn.
4PRO 7001-MHP FEATURES
400 WATT POWER HANDLING
139 DB MAX SPL
CONTROLLED DISPERSION, 60 X 40, LOWDISTORTION MID HIGH HORN
10” NEODYMIUM HIGH EFFICIENCY, LOWDISTORTION, SEALED BASKET, HORN LOADEDMIDRANGE
3” VOICE COIL, NEODYMIUM, TITANIUM DOME,HIGH FREQUENCY DRIVER, ALUMINIUM HORN
2 X NL4 NEUTRIK SPEAKON CONNECTORS BALTICBIRCH CABINET, 2 ALUMINIUM HANDLES FOREASY TRANSPORTATION AND POSITIONING
M10 FLY POINTS, 9 FLY TRACKS POINTS
4PRO 7001-BP is the mid-bass section,including 2 x 15”, 4” voice coil, highpower vented neodymium mid-bass.The two 15” are loaded in band-passhigh efficiency configuration.
4PRO 7001-BP
1m139 dB
2m123 dB
4m127 dB
16m115 dB
32m109 dB
8m121 dB
1600W
3”10”
2x15”
400W
4PRO 7001-MHP4PRO 7001-MHP is the twoway mid-high system in atrapezoidal enclosure foreasy array applications
34
The DX 4008 is a complete 4 input - 8 output digital loudspeakermanagement system designed for the touring or fixed sound installationmarkets. The absolute latest in available technology is utilized with 32-bit(40-bit extended) floating point processors and high performance 24-bitAnalog Converters. Sampling rate can be set to 96kHz. The high-bit DSPprevents noise and distortion induced by truncation errors of the commonlyused 24-bit fixed-point devices. A complete set of parameters include I/Olevels, delay, polarity, 6 bands of parametric EQ per channel,multiple crossover selections and full function limiters.
Precise frequency control is achieved with its 1 Hz resolution.Inputs and outputs can be routed in multiple configuration to meet anyrequirements.
The DX 4008 can be controlled or configured in real time on the frontpanel or with the intuitive PC GUI accessed via the RS 232 interface.Software upgrade for CPU and DSP via PC keeps the device current withnewly developed algorithms and functions once available. Multiple setupstorage and system security complete this professional package.
4PRO 7001-BP FEATURES
1600 WATT POWER HANDLING
139 DB MAX SPL
2 X 15” NEODYMIUM, HIGH POWER MID-BASS,100 MM INSIDE-OUTSIDE COPPER COIL
2 X NL4 NEUTRIK SPEAKON CONNECTORSBALTIC BIRCH CABINET, 4 ALUMINIUM HANDLESFOR EASY TRANSPORTATION AND POSITIONING
M10 FLY POINTS, 8 FLY TRACKS POINTS
4PRO 7001-BP
All components are housed in strong Balticbirch plywood enclosures. The woofers and mid-high horns are protected from a full front, strong,powder coated, metal grilles.
The cabinets features M10 threaded fly pointsand 8 each 3-position fly-tracks. Two side handlesfor easy portability for the 7001-MHP and 4 sidehandles for the 7001-BP.
35
LOUDSPEAKERMANAGEMENT SYSTEMDX4008
FEATURES
1000 WATT POWER HANDLING
133 DB MAX SPL
18” HIGH POWER WOOFER, 100 MMINSIDE/OUTSIDE COPPER COIL
RESPONSE DOWN TO 40 HZ
LOW PASS CROSSOVER AND HIGH PASS OUTPUT2 X NL4 SPEAKON® CONNECTOR
2 x NL4 SPEAKON® CONNECTOR
BALTIC BIRCH COMPACT ENCLOSURE AND 2SIDE HANDLES FOR EASY TRANSPORTATION
BUILT IN POLE MOUNT, TWO M10 POINTS FOROPTIONAL SPEAKER KART
1000W 18
RCF 4PRO 8001-S subwoofer integrates anRCF Precision Series low distortion, high powerwoofer a low pass / high pass output crossoverfilter in a small size, robust baltic birch plywoodenclosure. The result is a compact, high powersubwoofer remarkable for extended output and lowdistortion. This new high power 18” inch woofer is theresult of the latest refinement in years of RCFexperience in compact subwoofers design andmanufacture, resulting in a fast and controlledreproduction of the bass frequency range. Features
a 4” inside/outside copper voice coil to minimizepower compression and extend the life of thisproduct. The input section presents 2 x NL4 Speakon®connectors. The Baltic birch plywood enclosure is paintedwith black, heavy duty, textured epoxy. The front isprotected from a strong, powder coated, metalgrille. The cabinet features two M10 threaded pointsfor optional speaker kart, a 35 mm pole mountadaptor, two comfortable recessed side handles.
4PRO 8001-S is a Passive Technology high output bass reflex subwoofer system.Featuring a 18” newly designed RCF high power woofer. This compact enclosureprovides outstanding efficiency in sound pressure levels compared to the size. Perfectwhen you need to increase the system headroom and are looking for extended bassfrequency response, it is the ideal complement for existing active or passive PA.Applications include Sub Bass Add on’s for Main PA, Side Fills, Night Club and CorporateEvents
1m133 dB
2m127 dB
4m121 dB
16m109 dB
32m103 dB
8m115 dB
36
RCF PROFESSIONAL AMPLIFIERS
HC SERIESHigh Current Series Power Amplifiers
These professional stereo power amplifiers, working in class-H mode, providefrom 2 x 800 W up to 1 x 3200 W respectively, at an efficiency of around85%.
A massive transformer based power supply and hand selected componentsmake these power ratings possible with exceptional audio quality andabsolute reliability, even in the 2 ohm mode.
The output stages are fully protected against over-temperature, short circuit,RFI and equipped with soft start circuit and temperature-controlled fancooling.The integral soft clip limiter protects against damage to the connectedloudspeakers. The activity of a protective circuit, signal and limiter is shownfor each channel by LED’s.
Output (W) Stereoper Channel @ Ohm
Output (W) bridged @ 8 OhmOutput (W) bridged @ 4 OhmFrequency response ±0,2 dBFrequency response ±3 dBTHD + N
Input sensitivityInput impedanceDampening factorSlew RateInput connectionOutput connectionProtection
DimensionsWeight
800/2650/4350/81300160020Hz ÷ 20 KHz10Hz ÷ 65 KHz0,02 % at 1 KHz0,1 % to 20 KHz0,775 V20 kOhm bal./ 10 kOhm unbal.200:1 (8Ohm)50V/μS2 x 6,3mm jack and XLR / bal.2 x Speakon-4thermal, temerature,direct current, short circuit, RFI19", 2 U rack 19"17 kg/ 37 lbs
1000/2800/4500/81600200020Hz ÷ 20 KHz10Hz ÷ 65 KHz0,02 % at 1 KHz0,1 % to 20 KHz0,775 V20 kOhm bal./ 10 kOhm unbal.200:1 (8Ohm)50V/μS2 x 6,3mm jack and XLR / bal.2 x Speakon-4thermal, temerature,direct current, short circuit, RFI19", 2 U rack 19"18 kg/ 40 lbs
1600/21100/4700/82200320020Hz ÷ 20 KHz10Hz ÷ 65 KHz0,02 % at 1 KHz0,1 % to 20 KHz0,775 V20 kOhm bal./ 10 kOhm unbal.200:1 (8Ohm)50V/μS2 x 6,3mm jack and XLR / bal.2 x Speakon-4thermal, temerature,direct current, short circuit, RFI19", 3 U rack 19"29 kg/ 64 lbs
PRODUCT HC 1600 HC 2000 HC 3200
HC 1600
HC 2000
HC 3200
38
ED SERIESExtended Dynamic Power Amplifiers
A new and unique Class-H circuity technology using state of the art SMDSurface Mount Technology with a reduced number of components offeringperformance levels exceeding audiophile levels like a slew rate of 50V/μsand high-end extended dynamic sound. The high efficiency of the ED seriesenables maximum efficiency with low heat generation.The 2U amplifiers at 2 x 300 W or 2 x 550 W respectively into 4 ohms areequipped complete with temperature-controlled fan cooling, all commonprotective circuits such as over-temperature, short circuit, RFI and soft start.The integral soft clip limiter protects against damage to the connectedloudspeakers, the activity of a protective circuit, signal and limiter are shownfor each channel by LED’s.
ED 600
PRODUCT
Output (W) Stereoper Channel @ OhmOutput (W) bridged @ 8 OhmMono, one channel @ Ohm
Frequency response ±1dBFrequency response ±3dBTHD + NSMPTE IMDDampening factorSlew RateSelf noiseSignal to noise ratioInput sensitivityInput impedanceProtection
Input connectionOutput connectionCoolingCurrent consumptionDimensionsBuilt-in dimensionsWeight
2 x 300 / 42 x 180 / 81 x 600 / 81 x 310 / 41 x 195 / 820 ÷ 20.000 Hz20 ÷ 57.000 Hz0,05 % @ 1 KHz< 0,03% max. Power@4 Ohm> 200:1 (8 Ohm)50V/μS> 105 dB, A-weighted> 70dB@ 1 KHz0 dBm (0,775 V RMS)20 KOhm bal., 10 KOhm unbal.Thermal, direct current, RFI,short circuit, transformer protection2 x XLR bal., 6,3mm jack unbal.2 x Neutrik Speakon41 x temperature controlled ventilatormax. 6A88 x 482 x 350 mm + Handles 40mm2 U rack 19"12,5 kg/ 28 lbs
2 x 550 / 42 x 265 / 81 x 1100 / 81 x 570 / 41 x 325 / 820 ÷ 20.000 Hz20 ÷ 57.000 Hz0,05 % @ 1 KHz< 0,03% max. Power@4 Ohm> 200:1 (8 Ohm)50V/μS> 105 dB, A-weighted> 70dB@ 1 KHz0 dBm (0,775 V RMS)20 KOhm bal., 10 KOhm unbal.Thermal, direct current, RFI,short circuit, transformer protection2 x XLR bal., 6,3mm jack unbal.2 x Neutrik Speakon41 x temperature controlled ventilatormax. 10A88 x 482 x 350 mm + Handles 40mm2 U rack 19"15 kg/ 33 lbs
ED 600 ED 1100
ED 1100
39
PRODUCT SPECIFICATIONS All dimensions are in millimiter.
ART 705-AS
ART 310-A ART 310
ART 312-A ART 315-A ART 322-A ART 325-AART 522-A ART 525-A
600
590
435
345
680
405
337
537
315
345
680
405
ART 312 ART 315
PRODUCT SPECIFICATIONS
455
805
4704PRO 3001-A 4PRO 3002-SMA
410563
414
All dimensions are in millimiter.
520
700
700
4PRO 8001-AS 4PRO 8001-S 4PRO 8002-AS
470
1095455
4PRO 4001-A 4PRO 6001-A
4PRO 7001 A-BA 4PRO 7001 BA
525
920
550
700
523 694
4PRO 7001 A-MH 4PRO 7001 MH
496
659
263
519
PRODUCT
230 VOLT PART NUMBER
115 VOLT PART NUMBER
ACOUSTICAL SPEC.
Frequency response
Max SPL
Coverage angle
Compression driver
Midrange
Woofer
Power handling
INPUT SECTION
Input signal (Impedance)
Input connector
Output signal connector
Input sensitivity
Mic. input sensitivity
PROCESSOR SECTION
Crossover frequencies
Selectable high pass output
Protections
Limiter
Master volume
Phase switch
Music / Voice eq
Remote control option
AMPLIFIER
Nominal power
High frequencies
Mid frequencies
Low frequencies
Cooling
PHISICAL SPEC.
Height
Width
Depth
Weight
Cabinet
Hardware
Handles
Pole Mount / Cap
Colour
ART312-A
13000001
13000033
50 - 20 Khz
127 dB
90 x 60
neo 1"
—
12"
—
bal/unbal
jack/xlr
xlr
0 dBu
-40 dBu
1800 Hz
—
DC / short cir.
fast limiter
yes
—
yes
yes
350 Watt
ab / 50 Watt
—
H / 300 Watt
Convection
680
405
345
19 Kg
Composite PP
4 M10 flying points
2 side, 1 top
yes
Anthracite gray
ART322-A
13000003
13000035
45 - 20 Khz
128 dB
90 x 60
neo 2"
—
12"
—
bal/unbal
jack/xlr
xlr
0 dBu
-40 dBu
1200 Hz
—
DC / short cir.
fast limiter
yes
—
yes
yes
400 Watt
ab / 50 Watt
—
H / 350 Watt
Convection
680
405
345
23 Kg
Composite PP
4 M10 flying points
2 side, 1 top
yes
Anthracite gray
ART 310-A
13000059
13000065
50 - 20 Khz
127 dB
90 x 70
neo 1"
—
neo 10"
—
bal/unbal
jack/xlr
xlr
0 dBu
-40 dBu
1800 Hz
—
DC / short cir.
fast limiter
yes
—
yes
—
350 Watt
ab / 50 Watt
—
H / 300 Watt
Convection
537
337
315
12.4 Kg
Composite PP
2 M10 flying points
1 top
yes
Anthracite gray
ART315-A
13000002
13000034
50 - 20 Khz
128 db
90 x 60
neo 1"
—
15”
—
bal/unbal
jack/xlr
xlr
0 dBu
-40 dBu
1800 Hz
—
DC / short cir.
fast limiter
yes
—
yes
yes
350 Watt
ab / 50 Watt
—
H / 300 Watt
Convection
680
405
345
20 Kg
Composite PP
4 M10 flying points
2 side, 1 top
yes
Anthracite gray
ART325-A
13000004
13000036
45 - 20 Khz
129 db
90 x 60
neo 2"
—
15”
—
bal/unbal
jack/xlr
xlr
0 dBu
-40 dBu
1200 Hz
—
DC / short cir.
fast limiter
yes
—
yes
yes
400 Watt
ab / 50 Watt
—
H / 350 Watt
Convection
680
405
345
24 Kg
Composite PP
4 M10 flying points
2 side, 1 top
yes
Anthracite gray
PRODUCT SPECIFICATIONS
ART522-A
13000122
13000127
45 - 20 Khz
130
90 x 60
neo 2"
—
neo 12"
—
bal/unbal
jack/xlr
xlr
0 dBu
—
1200 Hz
—
DC/short cir.
fast/rms limiter
yes
—
—
—
750 Watt
Digtal 250 Watt
—
Digtal 500 Watt
Convection
680
405
345
16.6 Kg
Composite PP
4 M10 flying points
2 side, 1 top
yes
Anthracite gray
ART525-A
13000123
13000128
45 - 20 Khz
131
90 x 60
neo 2"
—
neo 15"
—
bal/unbal
jack/xlr
xlr
0 dBu
—
1200 Hz
—
DC/short cir.
fast/rms limiter
yes
—
—
—
750 Watt
Digtal 250 Watt
—
Digtal 500 Watt
Convection
680
405
345
17.2 Kg
Composite PP
4 M10 flying points
2 side, 1 top
yes
Anthracite gray
ART 705-AS
13000008
13000037
40- xover point
130 dB
—
—
—
15"
—
bal/unbal
jack/xlr
xlr
0 dBu
—
40- xover point
80/100/120 Hz
uC Protection
fast limiter
yes
yes
—
—
800 Watt
—
—
H / 800 Watt
Forced
590
435
600
37 Kg
Baltic Birch
2 M10 for kart
2 side
yes
Black
ART 312
13000031
—
45 - 20 Khz
127 dB
90 X 60
neo 1"
—
12"
300 w
8 ohm
speakon
speakon
—
—
1800 Hz
—
electronic
—
—
—
—
—
—
—
—
—
—
680
405
345
16 Kg
Composite PP
4 M10 flying points
2 side, 1 top
yes
Anthracite gray
ART 315
13000023
—
50 - 20 Khz
128 dB
90 X 60
neo 1"
—
15"
300 w
8 ohm
speakon
speakon
—
—
1800 Hz
—
electronic
—
—
—
—
—
—
—
—
—
—
680
405
345
17 Kg
Composite PP
4 M10 flying points
2 side, 1 top
yes
Anthracite gray
ART 310
13000075
—
50 - 20 Khz
127 dB
90 X 70
neo 1"
—
10"
300 w
8 ohm
speakon
speakon
—
—
1800 Hz
—
electronic
—
—
—
—
—
—
—
—
—
—
537
337
314
10 Kg
Composite PP
2 M10 flying points
1 top
yes
Anthracite gray
PRODUCT
230 VOLT PART NUMBER
115 VOLT PART NUMBER
ACOUSTICAL SPEC.
Frequency response
Max SPL
Coverage angle
Compression driver
Midrange
Woofer
Power handling
INPUT SECTION
Input signal (Impedance)
Input connector
Output signal connector
Input sensitivity
Mic. input sensitivity
PROCESSOR SECTION
Crossover frequencies
Selectable high pass output
Protections
Limiter
Master volume
Phase switch
Music / Voice eq
Remote control option
AMPLIFIER
Nominal power
High frequencies
Mid frequencies
Low frequencies
Cooling
PHISICAL SPEC.
Height
Width
Depth
Weight
Cabinet
Hardware
Handles
Pole Mount / Cap
Colour
PRODUCT SPECIFICATIONS
4PRO 3001-A
13000015
13000042
45 - 20 Khz
130 dB
80 x 60
neo 1"
x
15"
—
bal/unbal
jack/xlr
xlr
0 dBu
-40 dBu
1800 Hz
—
DC / short cir.
fast limiter
yes
—
yes
yes
400 Watt
ab / 50 Watt
—
H / 350 Watt
Forced
805
455
470
33 Kg
Baltic Birch
3 M10 flying points
2 side
yes
Black
4PRO 4001-A
13000016
13000041
45 - 20 Khz
130 dB
90 x 45
neo 1"
6"
15"
—
bal/unbal
jack/xlr
xlr
0 dBu
—
600 Hz / 2800 Hz
—
uC Protection
fast limiter
yes
—
—
—
800 Watt
ab / 50 Watt
H / 150 Watt
H / 600 Watt
Forced
1095
455
470
47 Kg
Baltic Birch
3 M10 flying points
2 side
—
4PRO 6001-A
13000007
13000040
50 - 20 Khz
134 dB
80 x 60
neo 1"
neo 8"
2 x neo 12"
—
bal/unbal
jack/xlr
xlr
0 dBu
—
360 Hz / 2000 Hz
—
uC Protection
fast limiter
yes
—
—
—
950 Watt
ab / 50 Watt
H / 300 Watt
H / 600 Watt
Forced
920
525
550
55 Kg
Baltic Birch
Five 3 position fly-tracks
2 side, 1 top
—
Black
4PRO 7001 A-MH
13000055
—
neo 2"
neo 10"
—
—
—
—
—
—
—
200 Hz / 1200 Hz
—
—
—
—
—
—
—
—
—
—
—
—
659
519
496
30.6 Kg
Baltic Birch
9 Fly Traks
2 side
—
Black
4PRO 7001 A-BA
13000054
13000080
—
—
2 x neo 15"
—
bal/unbal
jack/xlr
xlr
0 dBu
—
200 Hz
—
uC Protection
fast limiter
yes
yes
—
—
950 Watt
ab / 50 Watt
H / 300 Watt
H / 600 Watt
Forced
694
523
700
54 Kg
Baltic Birch
8 Fly Traks
4 side
—
Black
4PRO 3002-SMA
13000052
—
45 - 20 Khz
130 dB
40 x 60
neo 2"
x
neo 12"
—
bal/unbal
jack/xlr
xlr
0 dBu
-40 dBu
1100 Hz
—
DC / short cir.
fast limiter
yes
—
yes
yes
400 Watt
ab / 50 Watt
—
H / 350 Watt
Convection
414
410
563
25.4 Kg
Baltic Birch
—
1 side
—
Black
4PRO 8001-AS
13000005
13000038
40- xover point
133 dB
—
—
—
18"
—
bal/unbal
jack/xlr
xlr
0 dBu
—
40 Hz - xover point
80/100/120 Hz
uC Protection
fast limiter
yes
yes
—
—
800 Watt
—
—
H / 800 Watt
Forced
700
520
700
54 Kg
Baltic Birch
2 M10 for kart
2 side
yes
Black
4PRO 8002-AS
13000006
13000039
40- xover point
134 dB
—
—
—
18"
—
bal/unbal
jack/xlr
xlr
0 dBu
—
40 Hz - xover point
80/100/120 Hz
uC Protection
fast limiter
yes
yes
—
—
800 Watt
—
—
H / 800 Watt
Forced
700
520
700
56 Kg
Baltic Birch
2 M10 for kart
2 side
yes
Black
4PRO 7001 MHP
13000073
neo 3"
neo 10"
—
400 W
8 ohm
speakon
—
—
—
300 Hz (Active) / 1300 Hz (Passive)
—
—
—
—
—
—
—
—
—
—
—
—
659
519
496
33 Kg
Baltic Birch
9 Fly Traks
2 side
—
Black
4PRO 7001 BP
13000074
—
—
2 x neo 15"
1600 W
8 ohm
speakon
—
—
—
8 Hz (Active) or below 300 Hz (Active)
—
Electronic
—
—
—
—
—
—
—
—
—
—
694
523
700
54 Kg
Baltic Birch
8 Fly Traks
4 side
—
Black
4PRO 8001-S
13000020
40- xover point
134 dB
—
—
—
18"
1000 W
8 ohm
speakon
speakon
—
—
40 Hz - xover point
100 Hz
—
—
—
—
—
—
—
—
—
—
—
700
520
700
50 Kg
Baltic Birch
2 M10 for kart
2 side
yes
Black © 2
008
All R
ights
Res
erve
d, R
CF S
.p.A
.
Cod.10116096
EN
01/
2008
AG
C
RCF SpA Italy:tel. +39 0522 274 411 - fax +39 0522 232 428www.rcfaudio.com - e-mail: info@rcf.it
RCF UK Sales Office:tel. Int. +44 870 626 3142tel. UK 844 745 1234e-mail: info@rcfaudio.co.uk
RCF Germany Sales Office:tel. +49 2203 925370e-mail: germany@rcf.it
RCF USA Inc.:tel. +1 (603) 926-4604e-mail: info@rcf-usa.com
RCF France Sales Office:tel. +33 6 07501800e-mail: rcffrance@aol.com