Post on 19-Jan-2015
description
WELCOME TO MY
PRESENTATION
AHSANULLAH UNIVERSITY OF SCIENCE AND TECHNOLOGY
DEPARTMENT OF CIVIL ENGINEERING CE-416;PRESTRESS CONCRETE LAB COURSE TEACHER:MD.GALIB MUKTADIR
PRESENTATION OF AXIAL FORCE PRESENTED BY H.M SURUZZAMAN ID NO:10.01.03.63
BACKGROUND: Axial force is a force that tends to elongate or shorten a member & is normally measured in pounds. It is a system of internal forces whose resultant is force that is acting along the longitudinal axis of a structural member or assembly.
Axial force is the compression or tension force acting in a member. If the axial force acts through the censored of the member it is called concentric loading. If the force is not acting through the centroid it is called eccentric loading.
Eccentric loading produces a moment in the beam as a result of the load being a distaces away from the centroid.
Learning objectives are:-Understanding the theory ; it’s limitations, and it’
supplications for design & analysis of axial members
Axial members: Members with length significantly greater than the largest cross sectional dimension & with load applied along the longitudinal axis.
-Developing the discipline to draw free body diagrams & approximate deformed shapes in the
Design & analysis of structures.
Nature of axial force:-These forces are typically stretching force or compression force, depending on direction.-Shear forces occupies a similar position to axial force, but operates perpendicular to the centre axis of the object.-When a force is acting directly on the central axis, it is an axial force. These force will often compress the axis from either end or stretch the axis in two opposing directions; as a result the object typically does not move.
Figure of Axial Force
Example of axial force:A prime example of these forces can be seen on columns within buildings.
The column has an axis that runs through the entire from top to bottom. The column is constantly compressed as it supports the roof of the structure. In the column example, the axial force runs through the geometric centre of the form.
Axial Force on different members: Column Beam
Axial Force on different members: Shaft Cylinder
Calculation Formula :
Axial loading occurs when an object is loaded so that the force is normal to the axis that is fixed, as seen in the figure. Taking statics into consideration the force at the wall should be equal to the force that is applied to the part.
APPROACH OF WORK:Used to also solve statically indeterminate
problems by using superposition of the forces acting on the free-body diagram
First, choose any one of the two supports as “redundant” and remove its effect on the bar
Thus, the bar becomes statically determinateApply principle of superposition and solve the
equations simultaneously
+=
CompatibilityChoose one of the supports as redundant and write the equation of compatibility.Known displacement at redundant support (usually zero), equated to displacement at support caused only by external loads acting on the member plus the displacement at the support caused only by the redundant reaction acting on the member.
EquilibriumDraw a free-body diagram and write appropriate equations of equilibrium for member using calculated result for redundant force.Solve the equations for other reactions
EXAMPLE A-36 steel rod shown has diameter of 5 mm. It’s attached to fixed wall at A, and before it is loaded, there’s a gap between wall at B’ and rod of 1 mm.Determine reactions at A and B’.
CompatibilityConsider support at B’ as redundant. Use principle of superposition,
0.001 m = δP −δB
Equation 1( + )
CompatibilityDeflections δP and δB are determined from Eqn. 4-2
δP =PLAC
AE= … = 0.002037 m
δB = FB LAB
AE= … = 0.3056(10-6)FB
Substituting into Equation 1, we get
0.001 m = 0.002037 m − 0.3056(10-6)FB
FB = 3.40(103) N = 3.40 kN
EquilibriumFrom free-body diagram
− FA + 20 kN − 3.40 kN = 0
FA = 16.6 kN
+ Fx = 0;
THANK YOU