Post on 18-Oct-2020
Pneumatik für die Automobil-Industrie
Pneumatics for the Automobile Industry
Neumática para la industria del automóvil
Opel
Der Katalog auf CD-ROM/Catalogue on CD-ROM/Catálogo en CD-ROM
Gültigkeitsbereich
Scope
Campo de aplicación
Dieser Automobilkatalog basiert
auf der Standard Specification
(Kontrolliste Ausgabe April 2001)
und gilt für alle europäischen
Werke der Adam Opel AG.
This automobile catalogue is ba-
sed on the standard specification
(checklist edition April 2001) and
applies to all European factories
of Adam Opel AG.
Este catálogo de la industria au-
tomovilística se basa en la espe-
cificación estándar (lista de con-
trol editada en abril 2001) y es
válido en todas las plantas euro-
peas de Adam Opel AG.
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/05
Pneumatik für die Automobil-
Industrie
Opel
Ausgabe 05/2012
Alle technischen Angaben
entsprechen dem Stand der
Drucklegung.
Alle in dieser Schrift enthaltenen
Texte, Darstellungen, Abbildun-
gen und Zeichnungen sind Eigen-
tum der Festo AG & Co. KG und
damit urheberrechtlich
geschützt. Jede wie auch immer
geartete Vervielfältigung, Bear-
beitung, Übersetzung, Mikrover-
filmung sowie die Einspeicherung
und Verarbeitung in elektroni-
sche Systeme ist ohne Zustim-
mung der Festo AG & Co. KG un-
zulässig.
Durch den ständigen technischen
Fortschritt sind Änderungen
vorbehalten.
Festo AG & Co. KG
Postfach
73726 Esslingen
Ruiter Straße 82
73734 Esslingen
Deutschland
Pneumatics for the automotive
industry
Opel
05/2012 issue
All technical data applies at the
time of going to print.
All texts, representations, il-
lustrations and drawings inclu-
ded in this catalogue are the in-
tellectual property of Festo
AG & Co. KG and are protected by
copyright law. All rights reserved,
including translation rights. No
part of this publication may be
reproduced or transmitted in any
form or by any means, electronic,
mechanical, photocopying or
otherwise, without the prior writ-
ten permission of
Festo AG & Co. KG.
All technical data subject to
change according to technical
update.
Festo AG & Co. KG
P.O. Box
73726 Esslingen
Ruiter Straße 82
73734 Esslingen
Germany
Neumática para la industria
automovilística
Opel
Edición 05/2012
Todos los datos técnicos pueden
sufrir cambios en función de las
actualizaciones de los productos.
Todos los textos, gráficos, imáge-
nes y dibujos contenidos en esta
publicación son propiedad de
Festo AG & Co. KG y, en conse-
cuencia, están sujetos a los dere-
chos de autor. Queda prohibida
su reproducción, tratamiento,
traducción, microfilmación, me-
morización y procesamiento me-
diante sistemas electrónicos sin
previa autorización explícita de
Festo AG & Co. KG.
Festo se reserva el derecho de
efectuar modificaciones como re-
sultado de la constante innova-
ción de sus productos.
Festo AG & Co. KG
Apartado de correos
73726 Esslingen
Ruiter Straße 82
73734 Esslingen
Alemania
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 1
Automobilprogramm/Automobil range/Programa sector automóvilÜberblick/Overview/Información general
Seite
ISO-Zylinder 2
ISO-Ventile 23
Sonstige Produkte 36
Sonderausführungen 55
Berechnungssoftware 66
Page
ISO cylinders 2
ISO valves 23
Other products 36
Special designs 55
Engineering software 66
Página
Cilindros ISO 2
Válvulas ISO 23
Otros productos 36
Ejecuciones especiales 55
Software de ingeniería 66
es
en
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/052
ISO-Zylinder nach Opel NormKolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Inhaltsverzeichnis
Bezeichnung Festo Typ Opel-Norm
Material-Nr.
Seite
Zuganker-Zylinder
für Positionserkennung
und einstellbarer End-
lagendämpfung
DOG-...-PPV-A M13 01... 4
Grundzylinder mit mon-
tierter Schwenkzapfen-
befestigung
DOGZK-... M13 01... 4
Zylinder-Zubehör
Näherungsschalter
induktiv
SMTSO-...
SMBT-1
J06 13... 10
Fußbefestigung HNG-... M13 91... 12
Flanschbefestigung FNG-... M13 91... 13
Lagerstück LNZG-... M13 91... 14
Schwenkflansch SNGB-... M13 91... 15
Lagerbock, starr LNG-...
LN-...
M13 91... 16
Lagerbock
mit sphärischer
Lagerung
LSN-... M13 91... 17
Schwenkflansch SNG-... M13 91... 18
Lagerbock sphärisch LSNG-... M13 91... 19
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 3
ISO-Zylinder nach Opel NormKolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Inhaltsverzeichnis
Bezeichnung Festo Typ Opel-Norm
Material-Nr.
Seite
Gelenkkopf SGS-... M37 23... 20
Gabelkopf SG-... M13 91... 21
Flexo-Kupplung FK-... M13 91... 22
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/054
ISO-Zylinder nach Opel Norm, Material-Nr. M13 01...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
DOG-... DOGZK-...
Doppeltwirkender Zylinder
Festo Typ DOG
mit Schwenkzapfen,
Form E
DOGZK
-N- Durchmesser
32 ... 320 mm
-T- Hublänge
25 ... 500 mm
-L- Betriebsdruck max.
Kolben-∅ 32 ... 125 mm
12 bar
160 ... 320 mm
10 bar
-Q- Temperaturbereich
–20 ... +80 °C
– Medium:
gefilterte Druckluft–
geölt oder ungeölt
Grundzylinder ohne
Befestigungselemente.
Die Normzylinder entsprechen
den Normen
ISO 6431 (International)
DIN ISO 6431 und
VDMA 24 562 (Deutschland)
NF E 49 003.1 (Frankreich)
UNI 10 290 (Italien)
DIN
NF E 49 003.1
UNI 10 290
DOG-...-PPV-A
Zuganker-Zylinder für Positions-
erkennung und mit einstellbarer
Endlagendämpfung.
DOGZK-...-PPV-A
Zuganker-Zylinder mit Schwenk-
zapfen für Positionserkennung
und mit einstellbarer Endlagen-
dämpfung.
Die Schwenkzapfen sind serien-
mäßig in der Zylindermitte mon-
tiert.
Die außermittige Montage ist
möglich. Das gewünschte Maß
XG ist dabei anzugeben
(siehe Seite 8).
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 5
ISO-Zylinder nach Opel Norm, Material-Nr. M13 01...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Befestigungsmöglichkeiten
Einbau Grundzylinder
Befestigung vorn Befestigung hinten
Zubehör
Einbauvarianten mit
Befestigungselementen
Fußbefestigung
HNG-...
Flanschbefestigung
FNG-...
Zusätzliche Befestigungsbauteile
an der Kolbenstange
Gelenkkopf
SGS-...
vorn hinten
Lagerstück
LNZG-...
Schwenkflansch
SNGB-...
Gabelkopf
SG-...
Lagerbock, starr
LNG-...
LN-...
Lagerbock mit sphärischer
Lagerung
LSN-...
Flexo-Kupplung
FK-...
Schwenkflansch
SNG-...
Lagerbock, sphärisch
LSNG-...
Näherungsschalter
SMTSO-1-PS-S-LED-24
Befestigungsbausatz für
Näherungsschalter
SMBT-1
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/056
ISO-Zylinder nach Opel Norm, Material-Nr. M13 01...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Doppeltwirkender-Zylinder
DOG-...-PPV-A
∅ Opel-Material-Nr. M13 01...
[mm]
Hublänge
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
25 50 80 100 125
32
40
50
63
80
100
125
160
200
250
320
4000
4011
4022
4033
4044
4055
4066
4077
4088
4099
4110
4001
4012
4023
4034
4045
4056
4067
4078
4089
4100
4111
4002
4013
4024
4035
4046
4057
4068
4079
4090
4101
4112
4003
4014
4025
4036
4047
4058
4069
4080
4091
4102
4113
4004
4015
4026
4037
4048
4059
4070
4081
4092
4103
4114
164 430 DOG-32-...-PPV-A
164 431 DOG-40-...-PPV-A
164 432 DOG-50-...-PPV-A
164 433 DOG-63-...-PPV-A
164 434 DOG-80-...-PPV-A
164 435 DOG-100-...-PPV-A
164 436 DOG-125-...-PPV-A
164 437 DOG-160-...-PPV-A
164 438 DOG-200-...-PPV-A
164 439 DOG-250-...-PPV-A
164 440 DOG-320-...-PPV-A
∅ Opel-Material-Nr. M13 01...
[mm]
Hublänge
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
160 200 250 320 400 500
32
40
50
63
80
100
125
160
200
250
320
4005
4016
4027
4038
4049
4060
4071
4082
4093
4104
4115
4006
4017
4028
4039
4050
4061
4072
4083
4094
4105
4116
4007
4018
4029
4040
4051
4062
4073
4084
4095
4106
4117
4008
4019
4030
4041
4052
4063
4074
4085
4096
4107
4118
4009
4020
4031
4042
4053
4064
4075
4086
4097
4108
4119
4010
4021
4032
4043
4054
4065
4076
4087
4098
4109
4120
164 430 DOG-32-...-PPV-A
164 431 DOG-40-...-PPV-A
164 432 DOG-50-...-PPV-A
164 433 DOG-63-...-PPV-A
164 434 DOG-80-...-PPV-A
164 435 DOG-100-...-PPV-A
164 436 DOG-125-...-PPV-A
164 437 DOG-160-...-PPV-A
164 438 DOG-200-...-PPV-A
164 439 DOG-250-...-PPV-A
164 440 DOG-320-...-PPV-A
Bestellbeispiel: Kolben-∅ 80 mm, Hub 160 mm: 164 434 M13 01 4049
Opel-Bezeichnung eines Zylinders∅ 80 mm und Hub 160 mm:
Grundzylinder 80 x 160 VDMA 24 562 M13 01 4049
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 7
ISO-Zylinder nach Opel Norm, Material-Nr. M13 01...Kolben-∅ 32 ... 200 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Doppeltwirkender-Zylinder
mit Schwenkzapfen, Form E
DOGZK-...-PPV-A
∅ Opel-Material-Nr. M13 01...
[mm]
Hublänge
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
25 50 80 100 125
32
40
50
63
80
100
125
160
200
1484
1495
1506
1517
1528
1539
1550
1561
1572
1485
1496
1507
1518
1529
1540
1551
1562
1573
1486
1497
1508
1519
1530
1541
1552
1563
1574
1487
1498
1509
1520
1531
1542
1553
1564
1575
1488
1499
1510
1521
1532
1543
1554
1565
1576
164 441 DOGZK-32-...-PPV-A
164 442 DOGZK-40-...-PPV-A
164 443 DOGZK-50-...-PPV-A
164 444 DOGZK-63-...-PPV-A
164 445 DOGZK-80-...-PPV-A
164 446 DOGZK-100-...-PPV-A
164 447 DOGZK-125-...-PPV-A
164 448 DOGZK-160-...-PPV-A
164 449 DOGZK-200-...-PPV-A
∅ Opel-Material-Nr. M13 01...
[mm]
Hublänge
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
160 200 250 320 400 500
32
40
50
63
80
100
125
160
200
1489
1500
1511
1522
1533
1544
1555
1566
1577
1490
1501
1512
1523
1534
1545
1556
1567
1578
1491
1502
1513
1524
1535
1546
1557
1568
1579
1492
1503
1514
1525
1536
1547
1558
1569
1580
1493
1504
1515
1526
1537
1548
1559
1570
1581
1494
1505
1516
1527
1538
1549
1560
1571
1582
164 441 DOGZK-32-...-PPV-A
164 442 DOGZK-40-...-PPV-A
164 443 DOGZK-50-...-PPV-A
164 444 DOGZK-63-...-PPV-A
164 445 DOGZK-80-...-PPV-A
164 446 DOGZK-100-...-PPV-A
164 447 DOGZK-125-...-PPV-A
164 448 DOGZK-160-...-PPV-A
164 449 DOGZK-200-...-PPV-A
Bestellbeispiel: Kolben-∅ 80 mm, Hub 160 mm: 164 445 M13 01 1533
Opel-Bezeichnung eines Zylinders Form E,∅ 80 mm und Hub 160 mm:
Zylinder E 80 x 160 VDMA 24 562 M13 01 1533
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/058
ISO-Zylinder nach Opel Norm, Material-Nr. M13 01...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Doppeltwirkender Zylinder
DOG-...-PPV-A
DOG-32 ... 63 DOG-80 ... 320
DOGZK-...-PPV-A
1 Innensechskantschraube mit
Innengewinde für Befesti-
gungselemente
2 Regulierschraube für ein-
stellbare Endlagendämpfung
3 Ab∅ 125 mit zusätzlichen
Stangen zur Befestigung der
Näherungsschalter
+ = zuzüglich Hublänge
+½ = zuzüglich halbe Hublänge
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 9
ISO-Zylinder nach Opel Norm, Material-Nr. M13 01...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Doppeltwirkender Zylinder
DOG-...-PPV-A
DOGZK-...-PPV-A
∅
[mm]
AM B
∅
d11
BG C2 C3 D4
∅
D5
∅
E EE J2 J3 KK
32 22 30 17 71 86 37 6 50 Gx 7 – M10x1,25
40 24 35 16,5 87 105 45 6 55 G¼ 9,5 2,5 M12x1,25
50 32 40 17 99 117 55 8 65 G¼ 12 5,5 M16x1,5
63 32 45 19,5 116 136 68 8 75 Gy 14 6 M16x1,5
80 40 45 20 136 156 86 10 100 Gy 15 7 M20x1,5
100 40 55 20 164 189 107 10 120 G½ 13 8 M20x1,5
125 54 60 25 192 217 133 12 145 G½ 13 8 M27x2
160 72 65 24 245 280 168 16 186 G¾ 22 22 M36x2
200 72 75 24 295 330 210 16 230 G¾ 22 22 M36x2
250 84 90 25,5 – – 254 18 270 G1 25 25 M42x2
320 96 110 28,5 – – 325 22 340 G1 30 30 M48x2
∅
[mm]
L1 L2 L7 MM
∅
f8
PL RT TD
∅
e9
TG TK TL
32 19 94 ±0,4 5,8 12 8,8 M6 12 32,5 20 12
40 21,5 105 ±0,7 5,3 16 11 M6 16 38 25 16
50 28,5 106 ±0,7 2 20 17,5 M8 16 46,5 28 16
63 28,5 121 ±0,8 5 20 18 M8 20 56,5 30 20
80 34,5 128 ±0,8 8 25 17 M10 20 72 32 20
100 37,5 138 ±0,8 13 25 18 M10 25 89 38 25
125 46 160 ±1 14 32 18 M12 25 110 44 25
160 55 180 ±1,1 – 40 25 M16 32 140 48 32
200 65 180 ±1,6 – 40 28 M16 32 175 48 32
250 67 200 ±2 – 50 31 M20 – 220 – –
320 82 220 ±2 – 63 31 M24 – 240 – –
∅
[mm]
TM UW VA VD WH XG XJ XV ZJ ß1 ß3 ß4
32 50 68 4 10,5 26 62 84 73 120 10 6 –
40 63 72 4 10,5 30 69 96 82,5 135 13 6 –
50 75 86 4 12 37 80 100 90 143 17 8 –
63 90 98 4 12,5 37 87 108 97,5 158 17 8 –
80 110 110 4 16,5 46 101 119 110 174 22 – 17
100 132 136 4 15,5 51 112 128 120 189 22 – 17
125 160 160 6 20,5 65 136 154 145 225 27 – 19
160 200 200 6 – 80 155 185 170 260 36 – 32
200 250 240 6 – 95 165 205 185 275 36 – 32
250 – – 10 – 105 – – – 305 46 – 36
320 – – 10 – 120 – – – 340 55 – 46
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0510
Zylinder-Zubehör nach Opel Norm, Material-Nr. J06 13...Näherungsschalter für Kolben-∅ 32 ... 100 mm
SMTSO SMBT
Näherungsschalter, induktiv
mit gelber und grüner LED,
Schutzbeschaltung, störfest bei
AC-Schweißstromfeldern
(schweißfest)
SMTSO-1-PS-S-LED-24
Farbkennzeichnung
BK = schwarz
BN = braun
BU = blau
-P- Spannung
24 V DC, 250 V AC
-Q- Temperaturbereich
–25 ... +70 °C
– Schaltstrom max.:
200 mA
– Schaltspannung:
10 ... 30 V Gleichspannung
– Schaltausgang:
PNP
– Schutzart nach DIN 40 050:
IP 67
– Reproduzierbare Schalt-
genauigkeit:
± 0,1 mm
Dieser Näherungsschalter gibt
bei Annäherung eines Magnetfel-
des (z. B. Permanentmagnet auf
dem Zylinderkolben) ein elektri-
sches Signal ab. Der Schaltzu-
stand wird durch die gelbe LED
angezeigt.
Zubehör:
Befestigungsbausatz
(ist separat zu bestellen)
Festo Typ SMBT-1
Näherungsschalter Zubehör
Opel-Material-Nr. Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr. Festo Bestellbezeichnung
Teile-Nr. Typ
J06 13 0891 30 441 SMTSO-1-PS-S-LED-24 J06 91 0537 150 002 SMBT-1
Bestellbeispiel: Näherungsschalter, schweißfest: 30 441 J06 13 0891
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 11
Zylinder-Zubehör nach Opel Norm, Material-Nr. J06 13...Näherungsschalter für Kolben-∅ 32 ... 100 mm
Steckdosen mit Kabel
gerade Dosen abgewinkelte Dosen
Kabellänge
[m]
Teile-Nr. Typ Teile-Nr. Typ
2,5 159 428 SIM-M12-3GD-2,5-PU 159 430 SIM-M12-3WD-2,5-PU Ausführliche Produkt-
informationen siehe DVD und
www.festo.com/catalogue/sim
3 30 450 SIM-M12-RS-3GD-3 30 451 SIM-M12-RS-3WD-3
5 159 429 SIM-M12-3GD-5-PU 159 431 SIM-M12-3WD-5-PU
1 LED grün – Betriebsbereit-
schaft
2 LED gelb – Schaltzustand
3 Befestigungsbausatz
SMBT-1
4 Einbauraum für Steckdose
5 Theoretischer Schaltpunkt
Näherungsschalter
SMTSO-1-PS-S-LED-24
1 Näherungsschalter SMTSO-1
Befestigungsbausatz
SMBT-1
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0512
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Fußbefestigung
Festo Typ HNG
Lieferumfang:
2 Füße und 4 Befestigungs-
schrauben
∅
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40
50
63
80
100
125
160
200
250
320
32 947 HNG-32
32 948 HNG-40
32 949 HNG-50
32 950 HNG-63
32 951 HNG-80
32 952 HNG-100
32 953 HNG-125
34 476 HNG-160
34 477 HNG-200
157 510 HNG-250
157 511 HNG-320
M13 91 1662
M13 91 1663
M13 91 1664
M13 91 1665
M13 91 1666
M13 91 1667
M13 91 1668
M13 91 1669
M13 91 1670
M13 91 1671
M13 91 1672
Bestellbeispiel: Fußbefestigung für Kolben-∅ 50 mm: 32 949 M13 91 1664
Opel-Bezeichnung einer Fußbefestigung für Kolben-∅ 50 mm:
Fußbefestigung 50 VDMA 24 562 M13 91 1664
+ = zuzüglich Hublänge
∅
[mm]
Zylinder-
Schraube
DIN 912
AB
∅
H14
AH AO AT AU SA TR US XA
32 M6x18 7 32 6,5 4 24 142 32 45 144
40 M6x18 10 36 9 4 28 161 36 54 163
50 M8x20 10 45 9,5 5 32 170 45 64 175
63 M8x20 10 50 12,5 5 32 185 50 75 190
80 M10x20 12 63 15 6 41 210 63 93 215
100 M10x20 14,5 71 17,5 6 41 220 75 110 230
125 M12x25 16,5 90 22 8 45 250 90 131 270
160 M16x30 18,5 115 20 10 60 300 115 169 320
200 M16x30 24 135 30 12 70 320 135 214 345
250 M20x40 28 165 35 20 75 350 165 270 380
320 M24x45 35 185 40 23 85 390 200 340 425
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 13
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Lieferumfang:
1 Flansch und 4 Befestigungs-
schrauben
Flanschbefestigung
Festo Typ FNG
vorn hinten
∅
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40
50
63
80
100
125
160
200
250
320
32 940 FNG-32
32 941 FNG-40
32 942 FNG-50
32 943 FNG-63
32 944 FNG-80
32 945 FNG-100
32 946 FNG-125
34 478 FNG-160
34 479 FNG-200
157 508 FNG-250
157 509 FNG-320
M13 91 1640
M13 91 1641
M13 91 1642
M13 91 1643
M13 91 1644
M13 91 1645
M13 91 1646
M13 91 1647
M13 91 1648
M13 91 1649
M13 91 1650
Bestellbeispiel: Flanschbefestigung für Kolben-∅ 50 mm: 32 942 M13 91 1642
Opel-Bezeichnung einer Flanschbefestigung für Kolben-∅ 50 mm:
Flanschbefestigung 50 VDMA 24 562 M13 91 1642
+ = zuzüglich Hublänge
∅
[mm]
Zylinder-
Schraube
DIN 912
E FB
∅
MF R TF UF W ZF
32 M6x18 45 7 10 32 64 80 16 130
40 M6x18 54 9 10 36 72 90 20 145
50 M8x20 65 9 12 45 90 110 25 155
63 M8x20 75 9 12 50 100 120 25 170
80 M10x20 93 12 16 63 126 150 30 190
100 M10x20 110 14 16 75 150 175 35 205
125 M12x25 140 16 20 90 180 220 45 245
160 M16x30 180 18 20 115 230 280 60 280
200 M16x30 220 22 25 135 270 320 70 300
250 M20x30 270 26 25 165 330 390 80 330
320 M24x40 340 33 30 200 400 470 90 370
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0514
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Lagerstück
Festo Typ LNZG
Zur Aufnahme des Schwenk-
zapfens
Lieferumfang:
2 Lagerstücke
∅
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40/50
63/80
100/125
160/200
250
320
32 959 LNZG-32
32 960 LNZG-40/50
32 961 LNZG-63/80
32 962 LNZG-100/125
35 780 LNZG-160/200
157 516 LNZG-250
157 517 LNZG-320
M13 91 2310
M13 91 2311
M13 91 2312
M13 91 2313
M13 91 2314
M13 91 2315
M13 91 2316
Bestellbeispiel: Lagerstück für Kolben-∅ 50 mm: 32 960 M13 91 2311
Opel-Bezeichnung eines Satz Lagerstücke für Kolben-∅ 50 mm:
Lagerstücke 40/50 VDMA 24 562 M13 91 2311
∅
[mm]
CR
∅
DA
∅
H13
FK
∅
FN FS H1 HB
∅
H13
KE NH TH
±0,1
UL
32 12 D11 11 15 ±0,1 30 10,5 15 6,6 6,8 18 32 46
40 16 D11 15 18 ±0,1 36 12 18 9 9 21 36 55
50 16 D11 15 18 ±0,1 36 12 18 9 9 21 36 55
63 20 D11 18 20 ±0,1 40 13 20 11 11 23 42 65
80 20 D11 18 20 ±0,1 40 13 20 11 11 23 42 65
100 25 D11 20 25 ±0,1 50 16 24,5 14 13 28,5 50 75
125 25 D11 20 25 ±0,1 50 16 24,5 14 13 28,5 50 75
160 32 D11 26 30 ±0,2 60 22,5 36 18 17 40 60 92
200 32 D11 26 30 ±0,2 60 22,5 36 18 17 40 60 92
250 40 G7 33 35 ±0,2 70 27,5 45 22 21,5 50 90 140
320 50 G7 40 40 ±0,2 80 32,5 55 26 25,5 60 100 150
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 15
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Für Lagerbock LN, LNG und
LSN-...
Lieferumfang:
1 Schwenkflansch, 1 Bolzen mit
Sicherung und 4 Befestigungs-
schrauben
Schwenkflansch
Festo Typ SNGB
∅
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40
50
63
80
100
125
160
200
250
320
34 540 SNGB-32
34 541 SNGB-40
34 542 SNGB-50
34 543 SNGB-63
34 544 SNGB-80
34 545 SNGB-100
34 546 SNGB-125
34 547 SNGB-160
562 455 SNGB-200-B
157 512 SNGB-250
157 513 SNGB-320
M13 91 1651
M13 91 1652
M13 91 1653
M13 91 1654
M13 91 1655
M13 91 1656
M13 91 1657
M13 91 1658
M13 91 1659
M13 91 1660
M13 91 1661
Bestellbeispiel: Schwenkflansch für Kolben-∅ 50 mm: 34 542 M13 91 1653
Opel-Bezeichnung eines Schwenkflansches für Kolben-∅ 50 mm:
Schwenkflansch 50 VDMA 24 562 M13 91 1653
+ = zuzüglich Hublänge
∅
[mm]
Zylinder-
Schraube
DIN 912
CB
H14
CD
∅
FL L ML MR UB
h14
XC
32 M6x18 26 10 22 13 55 10 45 142
40 M6x18 28 12 25 16 63 12 52 160
50 M8x20 32 12 27 16 71 12 60 170
63 M8x20 40 16 32 21 83 16 70 190
80 M10x20 50 16 36 22 103 16 90 210
100 M10x20 60 20 41 27 127 20 110 230
125 M12x25 70 25 50 30 148 25 130 275
160 M16x30 90 30 55 35 188 25 170 315
200 M16x30 90 30 60 35 188 25 170 335
250 M20x30 110 40 70 47 231 40 200 375
320 M24x40 120 45 80 52 253 45 220 420
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0516
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Lagerbock, starr
Festo Typ LNG, LN
Für Schwenkflansch SNGB-...
Lieferumfang:
1 Lagerbock
∅
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40
50
63
80
100
125
160
200
250
320
33 890 LNG-32
33 891 LNG-40
33 892 LNG-50
33 893 LNG-63
33 894 LNG-80
33 895 LNG-100
33 896 LNG-125
9 037 LN-160
33 898 LNG-200
9 039 LN-250
9 040 LN-320
M13 91 1101
M13 91 1102
M13 91 1103
M13 91 1104
M13 91 0924
M13 91 1105
M13 91 1106
M13 91 1107
M13 91 1108
M13 91 1109
M13 91 1358
Bestellbeispiel: Lagerbock, starr für Kolben-∅ 50 mm: 33 892 M13 91 1103
Opel-Bezeichnung eines starren Lagerbocks für Kolben-∅ 50 mm:
Lagerbock 50 VDMA 24 562 M13 91 1103
∅
[mm]
BR BT CK
∅
EB
∅
H13
EM GL HB
∅
H13
OF PH RA TE UL UR
32 10 8 10 D11 – 25,8 –0,4 21 5,5 – 32 18 38 51 31
40 11 10 12 D11 – 27,8 –0,4 24 5,5 – 36 22 41 54 35
50 12 12 12 D11 – 31,8 –0,4 33 6,5 – 45 30 50 65 45
63 14,5 12 16 D11 15 40 c11 37 6,6 10,8 50 35 52 67 51
80 14,5 14 16 D11 20 50 c11 47 9 12,7 63 40 66 86 60
100 18,5 15 20 D11 20 60 c11 55 9 13,7 71 50 76 96 70
125 22 20 25 D11 20 70 c11 70 11 18,6 90 60 94 124 90
160 31 25 30 H8 20 90 c11 97 14 23,6 115 88 118 156 126
200 31 30 30 D11 26 90 c11 105 18 28,5 135 90 122 162 130
250 38,5 35 40 H8 33 110 c11 128 22 33,5 165 110 150 200 160
320 44,5 40 45 H8 40 120 c11 150 26 38,3 200 122 170 234 186
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 17
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Für Schwenkflansch SNGB-...
Lieferumfang:
1 Lagerbock und 2 Buchsen
Lagerbock
mit sphärischer Lagerung
Festo Typ LSN
∅
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40
50
63
80
100
125
160
200
250
320
5 561 LSN-32
5 562 LSN-40
5 563 LSN-50
5 564 LSN-63
5 565 LSN-80
5 566 LSN-100
6 987 LSN-125
6 988 LSN-160
6 989 LSN-200
6 990 LSN-250
6 991 LSN-320
M13 91 1223
M13 91 1359
M13 91 1287
M13 91 1285
M13 91 1286
M13 91 1360
M13 91 1361
M13 91 1362
M13 91 1363
M13 91 1364
M13 91 1365
Bestellbeispiel: Lagerbock mit sphärischer Lagerung für Kolben-∅ 50 mm: 5 563 M13 91 1287
Opel-Bezeichnung eines sphärischen Lagerbocks für Kolben-∅ 50 mm:
Lagerbock 50 VDMA 24 562 M13 91 1287
∅
[mm]
BR BT CK
∅
H7
EB
∅
EM GL HB
∅
LE OF PH RA TE UL UR
32 13 8 10 10 25,8 21 5,5 16 4,5 32 18 38 51 31
40 15 10 12 10 27,8 24 5,5 20 4,3 36 22 41 54 35
50 15 12 12 11 31,8 33 6,6 22 5,2 45 30 50 65 45
63 20 12 16 11 39,8 37 6,6 30 5,2 50 35 52 67 50
80 20 14 16 15 49,8 47 9 31 5 63 40 66 86 60
100 24 15 20 15 59,8 55 9 38 6 71 50 76 96 70
125 33 20 25 22 69,8 70 11 – 18 90 60 94 124 90
160 36 28 30 26 89,8 97 13,5 – 22 115 88 118 156 126
200 36 30 30 30 89,8 105 16 – 27 135 90 122 162 130
250 43 35 40 40 109,5 128 22 – 32 165 110 150 200 160
320 54 40 45 48 119,8 150 26 – 37 200 122 170 234 186
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0518
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 200 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Schwenkflansch
Festo Typ SNG
Für Lagerbock LSNG-...
Lieferumfang:
1 Schwenkflansch, 1 Bolzen mit
Sicherung und 4 Befestigungs-
schrauben
∅
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40
50
63
80
100
125
160
200
32 968 SNG-32
32 969 SNG-40
32 970 SNG-50
32 971 SNG-63
32 972 SNG-80
32 973 SNG-100
32 974 SNG-125
152 597 SNG-160
152 598 SNG-200
M13 91 1673
M13 91 1674
M13 91 1675
M13 91 1676
M13 91 1677
M13 91 1678
M13 91 1679
M13 91 1680
M13 91 1681
Bestellbeispiel: Schwenkflansch für Kolben-∅ 50 mm: 32 970 M13 91 1675
Opel-Bezeichnung eines Schwenkflansches für Kolben-∅ 50 mm:
Schwenkflansch 50 VDMA 24 562 M13 91 1675
1 Der Lagerbolzen ist mittels
Spannstift gegen Verdrehen
gesichert
+ = zuzüglich Hublänge
∅
[mm]
Zylinder-
Schraube
DIN 912
CG
H14
CP
d12
EK
∅
FL L SR XC
32 M6x18 14 34 10 22 13 11 142
40 M6x18 16 40 12 25 16 13 160
50 M8x20 21 45 16 27 16 15 170
63 M8x20 21 51 16 32 21 18 190
80 M10x20 25 65 20 36 22 20 210
100 M10x20 25 75 20 41 27 22 230
125 M12x25 37 97 30 50 30 26 275
160 M16x30 43 122 35 55 35 32 315
200 M16x30 43 122 35 55 35 32 335
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 19
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 200 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Für Schwenkflansch SNG-...
Lieferumfang:
1 Lagerbock
Lagerbock, sphärisch
Festo Typ LSNG
∅
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40
50
63
80
100
125
160
200
31 740 LSNG-32
31 741 LSNG-40
31 742 LSNG-50
31 743 LSNG-63
31 744 LSNG-80
31 745 LSNG-100
31 746 LSNG-125
152 599 LSNG-160
152 600 LSNG-200
M13 91 1684
M13 91 1685
M13 91 1686
M13 91 1687
M13 91 1688
M13 91 1689
M13 91 1690
M13 91 1691
M13 91 1692
Bestellbeispiel: Lagerbock, sphärisch für Kolben-∅ 50 mm: 31 742 M13 91 1686
Opel-Bezeichnung eines sphärischen Lagerbocks für Kolben-∅ 50 mm:
Lagerbock 50 VDMA 24 562 M13 91 1686
∅
[mm]
BR BT CN
∅
EB
∅
EN EU GL HB
∅
LE OF PH RA TE UL UR
32 15 10 10 11 14 10,5 21 6,6 16 9 32 18 38 51 31
40 17 10 12 11 16 12 24 6,6 20 9 36 22 41 54 35
50 20 12 16 14 21 15 33 9 24 11 45 30 50 65 45
63 22 12 16 14 21 15 37 9 27 11 50 35 52 67 50
80 27 14 20 17 25 18 47 11 31 12,5 63 40 66 86 60
100 29 15 20 17 25 18 55 11 38 13,5 71 50 76 96 70
125 39 20 30 19 37 25 70 14 50 18,5 90 60 94 124 90
160 42 28 35 20 43 28 97 14 45 25,5 115 88 118 156 126
200 42 35 35 26 43 28 97 18 45 31,8 135 88 122 162 130
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0520
Zylinder-Zubehör nach Opel Norm, Material-Nr. M37 23...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Gelenkkopf
Festo Typ SGS
Lieferumfang:
1 Gelenkkopf mit Sechskant-
mutter DIN 439
Nach DIN 648 Maßreihe K mit
Sechskantmutter nach DIN 439
Die Gelenkköpfe sind durch die
Werkstoffpaarung Stahl/PTFE-
Bronzegewebe im Schwenklager
wartungsfrei.
∅
[mm]
Kolbenstangen-
gewinde
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40
50/63
80/100
125
160/200
250
320
M6
M8
M10
M10x1,25
M12
M12x1,25
M16
M16x1,5
M20x1,5
M27x2
M36x2
M42x2
M48x2
9 254 SGS-M6
9 255 SGS-M8
9 256 SGS-M10
9 261 SGS-M10x1,25
9 257 SGS-M12
9 262 SGS-M12x1,25
9 258 SGS-M16
9 263 SGS-M16x1,5
9 264 SGS-M20x1,5
10 774 SGS-M27x2
10 775 SGS-M36x2
10 776 SGS-M42x2
10 777 SGS-M48x2
M37 23 0251
M37 23 0252
M37 23 0253
M37 23 0307
M37 23 0254
M37 23 0198
M37 23 0257
M37 23 0258
M37 23 0260
M37 23 0308
M37 23 0309
M37 23 0310
M37 23 0311
Bestellbeispiel: Gelenkkopf für Kolben-∅ 50 mm: 9 263 M37 23 0258
Opel-Bezeichnung eines Gelenkkopfes für Kolben-∅ 50 mm:
Gelenkkopf M16x1,5 M37 23 0258
Sechskantmutter
DIN 439
∅
[mm]
AV B1 CE CN
∅
H7
D1
∅
EF EN EU KK z ß1 ß2
– 12 3,2 30 6 13 10 9 6,8 M6 13 10 11
– 16 4 36 8 16 12 12 9 M8 13 13 14
25/32 20 5 43 10 19 14 14 10,5 M10 13 16 17
M10x1,25 17
40 22 6 50 12 22 16 16 12 M12 13 18 19
M12x1,25 19
50/63 28 8 64 16 27 21 21 15 M16 15 24 22
M16x1,5
80/100 33 10 77 20 34 25 25 18 M20x1,5 15 30 30
125 51 13,5 110 30 50 35 37 25 M27x2 15 41 41
160/200 56 18 125 35 58 40 43 28 M36x2 15 55 50
250 65 21 142 40 65 45 49 33 M42x2 15 65 55
320 75 24 160 50 75 57,5 60 45 M48x2 15 75 65
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 21
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 320 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Lieferumfang:
1 Gabelkopf mit Sechskant-
mutter nach DIN 439 und
1 Bolzen mit Sicherung
Lieferung erfolgt montiert.
Für schwenkbare Zylinderbe-
festigung mit Achsbolzen.
Der Gabelkopf wird am vorderen
Kolbenstangenende befestigt
und lässt eine Schwenkbewe-
gung des Zylinders in einer Ebene
zu.
Gabelkopf
Festo Typ SG
∅
[mm]
Kolben-
stangen-
gewinde
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr. DIN
ISO
8140
DIN
7152
32
40
50/63
80/100
125
160/200
250
320
M10x1,25
M12x1,25
M16x1,5
M20x1,5
M27x2
M36x2
M42x2
M48x2
6 144 SG-M10x1,25
6 145 SG-M12x1,25
6 146 SG-M16x1,5
6 147 SG-M20x1,5
14 987 SG-M27x2-B
9 581 SG-M36x2
9 582 SG-M42x2
9 583 SG-M48x2
M13 91 1062
M13 91 0452
M13 91 1059
M13 91 1034
M13 91 1096
M13 91 1057
M13 91 1097
M13 91 1098
X
X
X
X
X
X
X
X
X
X
X
–
–
–
–
–
Bestellbeispiel: Gabelkopf für Kolben-∅ 50 mm: 6 146 M13 91 1059
Opel-Bezeichnung eines Gabelkopfes für Kolben-∅ 50 mm:
Gabelkopf M16x1,5 M13 91 1059
Sechskantmutter
DIN 439
∅
[mm]
B1 B2 B3 CE
±0,4
CK
∅
H9
CM CV D1
∅
KK LE
±0,5
ß1
32 5 26 20 40 10 10 12 18 M10x1,25 20 17
40 6 31 24 48 12 12 14 20 M12x1,25 24 19
50/63 8 39 32 64 16 16 19 26 M16x1,5 32 24
80/100 10 54 40 80 20 20 25 34 M20x1,5 40 30
125 13,5 74 55 110 30 30 38 48 M27x2 54 41
160/200 18 92 70 144 35 35 44 60 M36x2 72 55
250 21 111 85 168 40 40 64 70 M42x2 84 65
320 24 123 90 192 50 50 73 80 M48x2 96 75
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0522
Zylinder-Zubehör nach Opel Norm, Material-Nr. M13 91...Kolben-∅ 32 ... 200 mm nach ISO 6431, VDMA 24 562 und NF E 49 003.1
Flexo-Kupplung
Festo Typ FK
Mit Sechskantmutter nach
DIN 439.
Die Kupplung verbindet das Kol-
benstangenende von Zylindern
aller Art mit den zu bewegenden
Maschinenteilen. Sie gleicht
Radial- und Winkelabweichungen
(Fluchtungsfehler) aus.
Lieferumfang:
1 Flexo-Kupplung mit Sechskant-
mutter
∅
[mm] Kolbenstangengewinde
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
32
40
50/63
80/100
125
160/200
M6
M8
M10
M10x1,25
M12x1,25
M16
M16x1,5
M20
M20x1,5
M27x2
M36x2
2 061 FK-M6
2 062 FK-M8
2 063 FK-M10
6 140 FK-M10x1,25
6 141 FK-M12x1,25
2 065 FK-M16
6 142 FK-M16x1,5
2 066 FK-M20
6 143 FK-M20x1,5
10 485 FK-M27x2
10 746 FK-M36x2
M13 91 0394
M13 91 0075
M13 91 0274
M13 91 1095
M13 91 1040
M13 91 0076
M13 91 0808
M13 91 0077
M13 91 0275
M13 91 1099
M13 91 1100
Bestellbeispiel: Flexo-Kupplung für Kolben-∅ 50 mm: 6 142 M13 91 0808
Opel-Bezeichnung einer Flexo-Kupplung für Kolben-∅ 50 mm:
Flexo-Kupplung M16x1,5 M13 91 0808
Winkelausgleich
Radialausgleich der Mittelachse
∅
[mm]
B1 D1
∅
D2
∅
D3
∅
L1 L2 L3 L4 L5 L6 KK ß1 ß2 ß3 ß4
– 3,2 8,5 14,5 5,8 37 25 4,4 17,5 11,5 15,7 M6 7 13 5 10
– 4 12,5 19 7,8 49 34 6 23,5 14 20,5 M8 10 17 7 13
32 5 21,8 32 13,8 67,5 49,5 9 34 23 31 M10 19 30 12 17
69,5 M10x1,25
40 6 21,8 32 13,8 74,5 50,5 10 34 24 32 M12x1,25 19 30 12 19
50/63 8 33,8 45 22 97 71 10 53 32 44,5 M16 30 41 19 24
103 M16x1,5
80/100 10 33,8 45 25 120 80 19 53 41 53,5 M20 30 41 19 30
M20x1,5
125 13,5 – 62 28 157 103 12,2 79 42 62,6 M27x2 55 55 24 41
160/200 18 – 80 36 251 179 22 136 78 110 M36x2 75 75 32 55
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 23
ISO-Ventile nach Opel NormInhaltsverzeichnis
Normventile
Bezeichnung Festo Typ Opel-
Material-Nr.
Seite
Magnetventile mit
Lochbild nach ISO 5599/1
ISO-Größe 1, 3 und 4
MDH-5/2-...
JMDH-5/2-...
MDH-5/3...
M32 ... 24
Magnetventile mit
Lochbild nach ISO 15407-1
Größe 01 und 02
VSVA-... M32 ... 28
Ventil-Zubehör
Bezeichnung Festo Typ Opel-
Material-Nr.
Seite
Steckdosen
nach DIN EN 175301-803
MSSD-...
KMEB-..
MEB-...
M32 91 ... 32
Anschlussplatten mit
Lochbild nach ISO 5599/1
Außenabmessungen nach
VDMA 24 345
ISO-Größe 1, 3 und 4
NAS-...
NAV-...
NEV-...
NDV-...
NSC-...
NZV-...
M32 91 ... 34
Anschlussplatten mit
Lochbild nach ISO 15407-1
Größe 01 und 02
NAS-...
NAW-...
NEV-...
NZV-...
NDV-...
35
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0524
ISO-Ventile nach Opel Norm, Material-Nr. M32 ...Magnetventile, Größe 1 (G¼), Größe 3 (G½) und Größe 4 (G¾) mit Lochbild nach ISO 5599/1
Magnetventil
Festo Typ MDH
Magnet-Impulsventil
Festo Typ JMDH
-M- Durchfluss
Größe 1
1200 l/min
Größe 3
4100 ... 4600 l/min
Größe 4
6000 l/min
-P- Spannung
24 V DC
230 V AC
24 V DC/42 V AC
-L- Betriebsdruck
2 ... 16 bar
-Q- Temperaturbereich
Umgebungstemperatur
–10 ... +50 °C
Mediumstemperatur
–10 ... +60 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– Wartungsfrei
– Überschneidungsfrei
– LABS1) -frei
– Befestigungsschrauben
unverlierbar
– Mit Handhilfsbetätigung
stoßend-rückstellend
– Schutzart (mit Steckdose)
IP 65
– ED 100%
– 3 Spannungen:
24 V DC,
Nennleistung 6,8W
230 V AC/50 Hz,
Halteleistung 10,5 VA
24 V DC/42 V AC/50 Hz,
Halteleistung 12,2 VA
Zubehör:
Steckdosen nach Opel-Norm und
DIN EN 175301-803, mit Betäti-
gungsanzeige grün und transpa-
rentem Gehäuse:
Typ A mit PG-Verschraubung grau
(für Anschluss 14).
Typ B mit PG-Verschraubung
schwarz (für Anschluss 12).
Steckdosen sind separat zu
bestellen, siehe Seite 32.
Ventil-Anschlussplatten siehe
Seite 34
1) LABS = Lackbenetzungsstörende Substanzen
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 25
ISO-Ventile nach Opel Norm, Material-Nr. M32 ...Magnetventile, Größe 1 (G¼), Größe 3 (G½) und Größe 4 (G¾) mit Lochbild nach ISO 5599/1
Technische Daten
Symbol ISO-Größe
ISO-Code
Opel-
Material-Nr.
Spannung Nenn-
weite
[mm]
Nenndurch-
fluss
1→ 2, 1→ 4
[l/min]
Be-
triebs-
druck
[bar]
Schalt-
zeit
bei 6 bar
Ein/Aus
[ms]
Festo Bestellbezeichnung
Teile-Nr. Typ
1 52 M32 15 0296 24 V DC/42 V AC 8 1200 3 ... 16 18/40 43 281 MDH-5/2-D-1-FR-C
M32 15 0297 230 V AC 43 282 MDH-5/2-D-1-FR-C
3 52 M32 15 0298 24 V DC/42 V AC 14,5 4500 3 ... 16 28/68 43 289 MDH-5/2-D-3-FR-C
M32 15 0299 230 V AC 43 290 MDH-5/2-D-3-FR-C
4 52 M32 15 0300 24 V DC/42 V AC 18 6000 3 ... 16 53/85 35 636 MDH-5/2-D-4-24-FR
M32 15 0301 230 V AC 35 636 MDH-5/2-D-4-230-FR
1 55 M32 15 0302 24 V DC/42 V AC 8 1200 2 ... 16 16/16 43 283 JMDH-5/2-D-1-C
M32 15 0303 230 V AC 43 284 JMDH-5/2-D-1-C
3 55 M32 15 0304 24 V DC/42 V AC 14,5 4500 2 ... 16 21/21 43 291 JMDH-5/2-D-3-C
M32 15 0305 230 V AC 43 292 JMDH-5/2-D-3-C
4 55 M32 15 0306 24 V DC/42 V AC 18 6000 2 ... 16 40/40 35 942 JMDH-5/2-D-4-24
M32 15 0307 230 V AC 35 942 JMDH-5/2-D-4-230
1 56 M32 18 0078 24 V DC/42 V AC 8 1200 3 ... 16 18/41 43 285 MDH-5/3G-D-1-C
M32 18 0079 230 V AC 43 286 MDH-5/3G-D-1-C
3 56 M32 18 0082 24 V DC/42 V AC 14,5 4100 3 ... 16 35/79 43 293 MDH-5/3G-D-3-C
M32 18 0083 230 V AC 43 294 MDH-5/3G-D-3-C
1 57 M32 18 0080 24 V DC/42 V AC 8 1200 3 ... 16 18/43 43 287 MDH-5/3E-D-1-C
M32 18 0081 230 V AC 43 288 MDH-5/3E-D-1-C
3 57 M32 18 0084 24 V DC/42 V AC 14,5 4600 3 ... 16 36/84 43 295 MDH-5/3E-D-3-C
M32 18 0085 230 V AC 43 296 MDH-5/3E-D-3-C
Bestellbeispiel: 5/2-Wege-Magnetventil für Spannungen von 24 V DC und 42 V AC geeignet:MDH-5/2-D-4-24-FR 35 636 M32 15 0300
Opel-Bezeichnung eines 5/2-Wegeventiles, ISO-Größe 4, monostabil, mit Magnetspule 24/42 Volt:
5/2-Wegeventil 4 - 24/42 V - M32 15 0300
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0526
ISO-Ventile nach Opel Norm, Material-Nr. M32 ...Magnetventile, Größe 1 (G¼), Größe 3 (G½) und Größe 4 (G¾) mit Lochbild nach ISO 5599/1
Magnetventil
MDH-5/2-...
5/2-Wegeventil
ISO-Größe 1 und 3
Magnet-Impulsventil
JMDH-5/2...
5/2-Wegeventil
ISO-Größe 1 und 3
Magnetventil
MDH-5/3...
5/3-Wegeventil
ISO-Größe 1 und 3
1 Anschlussbild nach
DIN EN 175301-803
2 Handhilfsbetätigung
3 Schrauben unverlierbar
Typ B1 B2 B3 B4 D1 H1 H2 H3 H4 H5 L1 L2 L3 L4 L5 L6
ISO-Größe 1
MDH-5/2-D-1-FR-C
42 28 6 30 M5 103 74,2 38 9 46,5
98 43,8
36 18 91,5JMDH-5/2-D-1-C 156 87,6 43,8
MDH-5/3...-D-1-C 108,4 54,2
ISO-Größe 3
MDH-5/2-D-3-FR-C
65 48 12 30 M8 120 91,2 55 12 63,5
164,7 72,7
64 32 111JMDH-5/2-D-3-C 194,4 145,4 72,7
MDH-5/3...-D-3-C 184 92
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 27
ISO-Ventile nach Opel Norm, Material-Nr. M32 ...Magnetventile, Größe 1 (G¼), Größe 3 (G½) und Größe 4 (G¾) mit Lochbild nach ISO 5599/1
Magnetventil
MDH-5/2-...
5/2-Wegeventil
ISO-Größe 4
Magnet-Impulsventil
JMDH-5/2-...
5/2-Wegeventile
ISO-Größe 4
1 Anschlussbild nach
DIN EN 175301-803
2 Handhilfsbetätigung
3 Schrauben unverlierbar
4 Magnet unabhängig von der
Handhilfsbetätigung um 90 °
umsetzbar
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0528
Normventile nach Opel Norm, Material-Nr. M32 ...Magnetventile, Größe 01 (G¼) und Größe 02 (Gx) mit Lochbild nach ISO 15407-1
Magnetventil
Festo Typ VSVA
-M- Durchfluss
Größe 01
1000 ... 1100 l/min
Größe 02
450 ... 550 l/min
-P- Spannung
24 V DC
230 V AC/50 Hz
-L- Betriebsdruck
2 ... 10 bar
-Q- Temperaturbereich
Umgebungstemperatur
–5 ... +50 °C
Mediumstemperatur
–5 ... +50 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– Wartungsfrei
– Überschneidungsfrei
– LABS1) -frei
– Elektrische Schnittstelle nach
DIN EN 175301-803
– Schutzart (mit Steckdose)
IP 65
– ED 100%
– 2 Spannung:
24 V DC,
Nennleistung 1,8W
230 V AC/50 Hz,
Halteleistung 2,1 VA
Flexibler Einsatz
Komfortable Montage
– Befestigungsschrauben und
Dichtung unverlierbar
Schnellmontage
– nur 2 Befestigungsschrauben
Abluft
– gefasste Abluft
– gefasste Vorsteuerabluft
Einfacher Service
– keine Schlauchdemontage
beim Ventilwechsel
Zubehör:
Steckdosen nach Opel-Norm und
DIN EN 175301-803.
Steckdosen sind separat zu
bestellen siehe Seite 32.
Ventil-Anschlussplatten siehe
Seite 34
1) LABS = Lackbenetzungsstörende Substanzen
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 29
Normventile nach Opel Norm, Material-Nr. M32 ...Magnetventile, Größe 01 (G¼) und Größe 02 (Gx) mit Lochbild nach ISO 15407-1
Technische Daten
Symbol ISO-Größe
ISO-Code
Opel-
Material-Nr.
Span-
nung
Nenn-
weite
[mm]
Nenn-
durchfluss
1→ 2,
1→ 4
[l/min]
Betriebs-
druck
[bar]
Schaltzeit
bei 6 bar
Ein/Aus
[ms]
Festo Bestellbezeichnung
Teile-Nr. Typ
01 52 M32 15 0420 24 V DC 9 1100 3 ... 10 26/56 546 702 VSVA-B-M52-MH-A1-1C1
M32 15 0421 230 V AC 547 220 VSVA-B-M52-MH-A1-3AC1
02 52 M32 15 0424 24 V DC 5 550 3 ... 10 17/35 546 703 VSVA-B-M52-MH-A2-1C1
M32 15 0425 230 V AC 547 221 VSVA-B-M52-MH-A2-3AC1
01 55 M32 15 0422 24 V DC 9 1100 2 ... 10 18/18 546 696 VSVA-B-B52-H-A1-1C1
M32 15 0423 230 V AC 547 214 VSVA-B-B52-H-A1-3AC1
02 55 M32 15 0426 24 V DC 5 550 2 ... 10 15/15 546 697 VSVA-B-B52-H-A2-1C1
M32 15 0427 230 V AC 547 215 VSVA-B-B52-H-A2-3AC1
01 56 M32 18 0114 24 V DC 9 1000 3 ... 10 23/58 546 708 VSVA-B-P53C-H-A1-1C1
M32 18 0115 230 V AC 547 226 VSVA-B-P53C-H-A1-3AC1
02 56 M32 18 0118 24 V DC 5 450 3 ... 10 18/30 546 709 VSVA-B-P53C-H-A2-1C1
M32 18 0119 230 V AC 547 227 VSVA-B-P53C-H-A2-3AC1
01 57 M32 18 0116 24 V DC 9 1000 3 ... 10 23/58 546 706 VSVA-B-P53E-H-A1-1C1
M32 18 0117 230 V AC 547 224 VSVA-B-P53E-H-A1-3AC1
02 57 M32 18 0120 24 V DC 5 450 3 ... 10 18/30 546 707 VSVA-B-P53E-H-A2-1C1
M32 18 0121 230 V AC 547 225 VSVA-B-P53E-H-A2-3AC1
Bestellbeispiel: 5/2-Wege-Magnetventil für Spannungen von 24 V DC: VSVA-B-M52-MH-A1-1C1 546 702 M32 15 0420
Opel-Bezeichnung eines 5/2-Wegeventiles, ISO-Größe 01, monostabil, mit Magnetspule 24 Volt:
5/2-Wegeventil 01 - 24 V - M32 15 0420
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0530
Normventile nach Opel Norm, Material-Nr. M32 ...Magnetventile, Größe 01 (G¼) und Größe 02 (Gx) mit Lochbild nach ISO 15407-1
Magnetventil
VSVA-B-M52...
5/2-Wegeventil monostabil
1 Anschlussmaße und Geräte-
stecker nach
DIN EN 175301-803, Form C
2 Handhilfsbetätigung
3 Schrauben unverlierbar
4 Nut für Bezeichnungsschild
Typ B1 B2 D1 H1 H2 H3 H4 H5 L1 L2 L3 L4 L5
ISO-Größe 01
VSVA-B-M52... 26,3 19 M4 89,2 71,2 62,6 39,3 7 113,1 63,1 29,75 61,6 123,2
ISO-Größe 02
VSVA-B-M52... 18 12,5 M3 80,6 62,2 53,6 30,3 5,4 95,4 53,9 21,25 53,1 102,2
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 31
Normventile nach Opel Norm, Material-Nr. M32 ...Magnetventile, Größe 01 (G¼) und Größe 02 (Gx) mit Lochbild nach ISO 15407-1
Magnetventil
VSVA-B-M52...
5/2-Wegeventil bistabil,
5/3-Wegeventil
1 Anschlussmaße und Geräte-
stecker nach
DIN EN 175301-803, Form C
2 Handhilfsbetätigung
3 Schrauben unverlierbar
4 Nut für Bezeichnungsschild
Typ B1 B2 D1 H1 H2 H3 H4 H5 L1 L2 L3 L4 L5
ISO-Größe 01
VSVA-B-M52... 26,3 19 M4 89,2 71,2 62,2 39,3 7 126,2 63,1 29,75 61,6 123,2
ISO-Größe 02
VSVA-B-M52... 18 12,5 M3 80,6 62,2 53,6 30,3 5,4 107,8 53,9 21,25 53,1 102,2
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0532
Ventil-Zubehör nach Opel Norm, Material-Nr. M32 91 ...Steckdosen nach DIN EN 175301-803
KMEB MEBMSSD-EB MSSD-C
Steckdose
Festo Typ MSSD
Steckdose mit Kabel
Festo Typ KMEB
Leuchtende Dichtung
Festo Typ MEB
– Steckdosen MSSD
mit Anschlussbild
DIN EN 175301-803
– Mit transparentem Gehäuse,
Profildichtung und grüner LED
– Schutzart IP 65
– Steckdosen mit Kabel KMEB
mit Anschlussbild
DIN EN 175301-803
– Kabellängen 2,5 und 5 m
– Schutzart IP 65
– Leuchtende DichtungMEB
mit gelber LED
– Schutzart IP 65
– Schutzbeschaltung
Ausführliche Produkt-
informationen siehe DVD und
www.festo.com/catalogue/<typ>
Steckdose
DIN EN 175301-803 für
Ventile nach ISO 5599/1
Spannung Kabel-
länge
Kabelverschraubung/
Farbe
Opel-
Material-Nr.
Typ Festo Bestellbezeichnung
Teile-Nr. Typ
Form A mit grüner LED
Gehäuse transparent
24 V DC – Pg11/grau M32 91 2648 A** 35 945 MSSD-C14-TG-24=Opel
Pg11/schwarz M32 91 2649 B*** 35 944 MSSD-C12-TS-24=Opel
Form A mit grüner LED
Gehäuse transparent
230 V AC – Pg11/grau M32 91 2242 A** 35 949 MSSD-C14-TG-230~Opel*
Pg11/schwarz M32 91 2243 B*** 35 948 MSSD-C12-TS-230~Opel*
Form A ohne LED – – Pg9/schwarz M32 91 0349 B*** 34 583 MSSD-C
Steckdose
DIN EN 175301-803 für
Ventile nach VDMA 24 563
Form C Flachdichtung – – Pg7 – – 151 687 MSSD-EB
Form C mit gelber LED
Schutzbeschaltung
24 V DC 2,5 m – – – 151 688 KMEB-1-24-2,5-LED
5 m – – 151 689 KMEB-1-24-5-LED
Form C
ohne LED
230 V AC 2,5 m – – – 151 690 KMEB-1-230-2,5
5 m – – 151 691 KMEB-1-230-5
Leuchtende Dichtung 24 V DC – – – – 151 717 MEB-LD-12-24
230 V AC – – 151 718 MEB-LD-230
* auf Anfrage ** Typ A für Ventilanschluss 14 *** Typ B für Ventilanschluss 12
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 33
Ventil-Zubehör nach Opel Norm, Material-Nr. M32 91 ...Steckdosen nach DIN EN 175301-803
12 ... 24 V 230 V Schaltbilder
1 Einsatz jeweils um 90°
umsetzbar
Steckdose
MSSD-C14-TG-...
MSSD-C12-TS-...
1 Einsatz jeweils um 90°
umsetzbar
Steckdose
MSSD-C14-C
MSSD-C
1 Einsatz jeweils um 90°
umsetzbar
Steckdose
MSSD-EB
3 Beleuchtungsfeld LED
5 Schaltbild
8 Bezeichnungsclip
aB Anschlussbild nach
DIN EN 175301-803
aC Leitung 3 x 0,5 mm2
Steckdose mit Kabel
KMEB-...
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0534
Ventil-Zubehör nach Opel Norm, Material-Nr. M32 91 ...ISO-Anschlussplatten, Größe 1 (G¼), Größe 3 (G½) und Größe 4 (G¾) mit Lochbild nach ISO 5599/1 und Außenabmessungen nach VDMA 24 345
Anschlussplatten
ISO 5599/1
Benennung Größe Opel-Material-Nr. Teile-Nr. Typ
Einzel-Abschlussplatte
Anschlüsse seitlich
Form A
1 M32 91 2221 9 484 NAS-¼-1A-ISO
3 M32 91 2224 10 336 NAS-½-3A-ISO
4 M32 91 2227 152 813 NAS-¾-4A-ISO
Reihen-Abschlussplatte
(Verkettungsplatte)
Form C
1 M32 91 2222 10 173 NAV-¼-1C-ISO
3 M32 91 2225 10 175 NAV-½-3C-ISO
4 M32 91 2228 11 139 NAV-¾-4C-ISO
Endplatten-Bausatz
(linke und rechte Endplatte)
Form D
1 M32 91 2223 10 174 NEV-1DA/DB-ISO
3 M32 91 2226 10 176 NEV-3DA/DB-ISO
4 M32 91 2229 11 140 NEV-4DA/DB-ISO
Abdeckplatte 1 M32 91 2230 9 489 NDV-1-ISO
3 M32 91 2231 10 340 NDV-3-ISO
4 M32 91 2232 11 142 NDV-4-ISO
Verschlussscheibe 1 M32 91 2233 11 550 NSC-¼-1-ISO
3 M32 91 2234 11 551 NSC-½-3-ISO
4 M32 91 2235 11 699 NSC-¾-4-ISO
Zwischenplatte zur Verkettung der
ISO-Größe 1 auf
ISO-Größe 3
1 M32 91 2244 12 911 NZV-3-2/1
3 M32 91 2244
– –
Bestellbeispiel: Endplatten-Bausatz, Form D, Größe 1: 10 174 M32 91 2223
Form A: Einzel-Abschlussplatte,
Anschlussgewinde
seitlich
Form C: Verkettungsplatte,
Anschlussgewinde für
Arbeitsleitung unten,
Steuerleitung seitlich
Form D: Endplatte zu
Verkettungsplatte
Form C
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 35
Ventil-Zubehör nach Opel NormVDMA-Anschlussplatten, Größe 01 (G¼) und Größe 02 (Gx) mit Lochbild nach ISO 15407-1
Anschlussplatten
ISO 15407-1
Benennung Größe Opel-Material-Nr. Teile-Nr. Typ
Einzel-Abschlussplatte
Anschlüsse seitlich
01 – 161 109 NAS-¼-01-VDMA
02 – 161 115 NAS-x-02-VDMA
Verkettungsplatte
für Pneumatikventile
4
2
12
01 – 161 103 NAW-¼-01-VDMA-VL
02 – 161 111 NAW-x-02-VDMA-VL
Verkettungsplatte
für Magnetventile
4
2
12
01 – 161 102 NAW-¼-01-VDMA
02 – 161 110 NAW-x-02-VDMA
Endplatte 01 – 161 104 NEV-01-VDMA
02 – 161 112 NEV-02-VDMA
Zwischenplatte 01/02 – 161 108 NZV-01/02-VDMA
Abdeckplatte 01 – 161 107 NDV-01-VDMA
02 – 161 114 NDV-02-VDMA
Bestellbeispiel: Endplatte, Größe 01: 161 104 NEV-01-VDMA
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0536
Sonstige Produkte nach Opel NormInhaltsverzeichnis
Bezeichnung Opel-
Material-Nr.
Festo Typ Seite
Ventile Drossel-Rückschlagventil M32 06 ... GRLA-...-B 37
Schnellentlüftungsventil M32 08 0026 SE-¼-B 38
Abluftdrossel M32 11 ... GRU-½-B
GRE-...
39
Kugelhahn M22 07 ... QH-... 40
Einzelgeräte Manometer M15 04 ... MA-... 41
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 37
Sperr- und Stromventile für Antriebe nach Opel Norm, Material-Nr. M32 06 ...Drossel-Rückschlagventile, Gx ... G¾
Drossel-Rückschlagventil
Festo Typ GRLA
-M- Durchfluss
0 ... 2000 l/min
-L- Betriebsdruck
0,3 ... 10 bar
-Q- Temperaturbereich
–10 ... +60 °C
– Medium:
gefilterte Druckluft–
geölt oder ungeölt
Drossel-Rückschlagventile mit
Abluft-Drosselung
werden zur Regulierung der
Durchflussmengen der Abluft bei
doppeltwirkenden Zylindern ein-
gesetzt. In umgekehrter Richtung
strömt die Luft über das Rück-
schlagventil und hat vollen
Durchgangsquerschnitt.
– Gewindeanschluss Gx bis G¾
– Direkt am Zylinder montierbar
– Schwenkbar um 360°
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
151 165 GRLA-x-B M32 06 0081
151 172 GRLA-¼-B M32 06 0095
151 178 GRLA-y-B M32 06 0096
151 179 GRLA-½-B M32 06 0150
151 180 GRLA-¾-B M32 06 0154
Bestellbeispiel: Drossel-Rückschlagventil mit Gewindeanschluss G¼: 151 172 M32 06 0095 Ausführliche Produkt-
informationen siehe DVD und
www.festo.com/catalogue/grlaOpel-Bezeichnung eines Drossel-Rückschlagventiles mit Anschlussgewinde G¼:
Drossel-Rückschlagventil G¼M32 06 0095
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0538
Sperr- und Stromventile für Antriebe nach Opel Norm, Material-Nr. M32 08 ...Schnellentlüftungsventile G¼
Schnellentlüftungsventil
ohne Schalldämpfer
Festo Typ SE-¼-B
-M- Durchfluss
300 ... 660 l/min
-L- Betriebsdruck
0,5 ... 10 bar
-Q- Temperaturbereich
–20 ... +75 °C
– Medium:
gefilterte Druckluft–
geölt oder ungeölt
– Gefasste Abluft
Mit diesen Elementen können er-
höhte Kolbengeschwindigkeiten
bei einfach- und doppeltwirken-
den Zylindern im Rücklauf er-
reicht werden.
Die Druckluft strömt vom Steuer-
ventil über das Schnellentlüf-
tungsventil zum Zylinder. Die Ent-
lüftung 3 wird dabei verschlos-
sen. Fällt der Druck bei 1 ab, so
wird von 2 nach 3 entlüftet.
Um eine volle Schnellentlüftung
zu erreichen, muss das Ventil
direkt an den Luftanschluss des
Zylinders angebaut werden.
Das Entlüftungsgeräusch wird
durch Schalldämpfer vermindert.
Gewindeanschluss Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
G¼ 9 686 SE-¼-B M32 08 0026
Ausführliche Produkt-
informationen siehe DVD und
www.festo.com/catalogue/se
Bestellbeispiel: Schnellentlüftungsventil mit Gewindeanschluss G¼: 9 686 M32 08 0026
Opel-Bezeichnung eines Schnellentlüftungsventiles mit Anschlussgewinde G¼:
Schnellentlüftungsventil G¼M32 08 0026
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 39
Sperr-, Strom- und Druckventile nach Opel Norm, Material-Nr. M32 11 ...Drosselventil Gx ... G½
GRE-... GRU-...-B
Abluftdrossel
Festo Typ GRU-.../GRE
-M- Durchfluss
520 ... 8000 l/min
-L- Betriebsdruck max.
0 ... 10 bar
-Q- Temperaturbereich
–10 ... +70 °C
– Medium:
gefilterte Druckluft–
geölt oder ungeölt
Diese Ventile werden in die Ent-
lüftungsanschlüsse 3 bzw. 5 von
Steuerventilen eingeschraubt
und ermöglichen die Regulierung
der Kolbengeschwindigkeit von
Zylindern durch Drosseln der
Abluft.
Die Drosselschraube ermöglicht
eine einstellbare Begrenzung des
Luftaustritts. Die ausströmende
Luft entweicht über den inte-
grierten Schalldämpfer unter ver-
minderter Geräuschentwicklung.
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
9 519 GRU-½-B M32 11 0248
10 351 GRE-x M32 11 0259
10 352 GRE-¼ M32 11 0260
10 353 GRE-½ M32 11 0261
Bestellbeispiel: Abluftdrossel mit Gewindeanschluss G¼: 10 352 M32 11 0260 Ausführliche Produkt-
informationen siehe DVD und
www.festo.com/catalogue/greOpel-Bezeichnung einer Abluftdrossel mit Anschlussgewinde G¼:
Drosselventil G¼M32 11 0260
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0540
Sperr, Strom- und Druckventile nach Opel Norm, Material-Nr. M22 07 ...Absperrventile Gy ... G1½
Kugelhahn
Festo Typ QH
-M- Durchfluss
bis 84000 l/min
-L- Betriebsdruck
–0,95 ... +30 bar
-Q- Temperaturbereich
–30 ... +200 °C
-R- Unterdruck
für Vakuum geeignet
– Medium:
gefilterte Druckluft–
geölt oder ungeölt
Mit diesen Ventilen wird durch
Hebelschwenkung der Luftdurch-
fluss in beiden Richtungen voll-
ständig abgesperrt.
-H- HinweisDiese Ausführung ist nicht für
giftige Gase geeignet, z.B.
Erdgas, Stadtgas usw.
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
9 542 QH-y M22 07 0003
9 544 QH-¾ M22 07 0007
9 545 QH-1 M22 07 0008
6 837 QH-1½ M22 07 0011
Ausführliche Produkt-
informationen siehe DVD und
www.festo.com/catalogue/qh
Bestellbeispiel: Kugelhahn mit Gewindeanschluss Gy: 9 542 M22 07 0003
Opel-Bezeichnung eines Kugelhahns mit Anschlussgewinde Gy:
Absperrhahn QH-Gy ohne Entlüftung M22 07 0003
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 41
Einzelgeräte zur Druckluftaufbereitung nach Opel Norm, Material-Nr. M15 04 ...Anzeigegeräte, G¼
Manometer
Festo Typ MA
Form E, Anschlusszapfen
rückseitig zentrisch,
ohne Befestigungsrand
-Q- Temperaturbereich
–10 ... +60 °C
Für allgemeine Anwendungen
nach DIN EN 837-1
– Medium:
gefilterte Druckluft–
geölt oder ungeölt
– Anzeigebereich 0 ... 16 bar
– Anschluss G¼
Diese Manometer dienen der
Druckmessung und -anzeige in
Steuerungen.
Sie sind frei von lackbenetzungs-
störenden Substanzen.
Manometer dürfen bei Dauer-
betrieb (Ruhebelastung) nur bis
zu¾ ihres Skalenendwertes
belastet werden.
Anzeigebereich
[bar]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
0 ... 2,5 162 845 MA-63-2,5-¼-EN M15 04 0306
0 ... 10 162 840 MA-63-10-¼-EN M15 04 0057
0 ... 16 162 841 MA-63-16-¼-EN M15 04 0079
Bestellbeispiel:Manometer, Anzeigebereich 0 bis 16 bar: 162 841 M15 04 0079 Ausführliche Produkt-
informationen siehe DVD und
www.festo.com/catalogue/maOpel-Bezeichnung eines Manometers, Form E, Anzeigebereich 0 bis 16 bar:
Überdruckmessgerät 1,6E 0 – 16 M15 04 0079
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0542
Zylinder nach Opel NormInhaltsverzeichnis
Bezeichnung Festo Typ Seite
Mehrstellungszylinder
Mehrstellungszylinder
Antriebszylinder für
Euro-C-Zangen
Kolben-∅ 70 und 90 mm
D-...-PV2-C-SA 43
Mehrstellungszylinder
Antriebszylinder für
Euro-X-Zangen
Kolben-∅ 80 ... 125 mm
DNG-...-30-100-P-SA 45
Mehrstellungszylinder
Antriebszylinder für
Euro-X-Zangen
Kolben-∅ 100 ... 125 mm
D-...-60-30-PV2-SA 47
Doppeltwirkende Zylinder
Doppeltwirkender Zylinder
Einsatz als Ziehteilheber in
Presswerkzeugen
Kolben-∅ 35 mm
D-35-...-PP-SA 49
Doppeltwirkender Zylinder
Ausgleichszylinder für
Euro-X-Zangen
Kolben-∅ 50 und 63 mm
D-...-20-P-SA 51
Doppeltwirkender Zylinder
Ausgleichszylinder für
Euro-C-Zangen
Kolben-∅ 32 mm
D-...-35-P-SA 53
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 43
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkende Zylinder, Kolben-∅ 70 und 90 mm
Mehrstellungszylinder
Antriebszylinder für Euro-C-Zange
Festo Typ D-...-PV2-C-SA
-N- Durchmesser
70 und 90 mm
-T- Hublänge
Vorhub
30 ... 120 mm
Arbeitshub
46 mm
-L- Betriebsdruck
max. 12 bar
-Q- Temperaturbereich
–20 ... +80 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– Dreistellungszylinder mit Vor-
und Arbeitshub
– Einsatz in Schweißzangen
– Verstärkte Kolbenstange
– Verstärkte Lagerung
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0544
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkende Zylinder, Kolben-∅ 70 und 90 mm
Mehrstellungszylinder
D-...-PV2-C-SA
∅
[mm]
Vorhub
[mm]
Arbeitshub
[mm]
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
70 30 46 197639 D-70-30-46-PV2-C-SA M13 01 9760
50 197638 D-70-50-46-PV2-C-SA M13 01 6128
80 197637 D-70-80-46-PV2-C-SA M13 01 5274
100 197636 D-70-100-46-PV2-C-SA M13 01 6129
120 197635 D-70-120-46-PV2-C-SA M13 01 5272
90 30 46 197645 D-90-30-46-PV2-C-SA M13 01 9763
50 197644 D-90-50-46-PV2-C-SA M13 01 6130
80 197643 D-90-80-46-PV2-C-SA M13 01 5277
100 197642 D-90-100-46-PV2-C-SA M13 01 6131
120 197641 D-90-120-46-PV2-C-SA M13 01 5276
Bestellbeispiel: Mehrstellungszylinder Kolben-∅ 70 mm, Vorhub 100 mm, Arbeitshub 46 mm:
197636 D-70-100-46-PV2-C-SA
D-70-... (Werte in Klammern)
D-90-...
1 Arbeitshub vor
2 Vorhub vor
3 Rückhub
4 Regulierschraube für
Endlagendämpfung
+ VH = zuzüglich Vorhub
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 45
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkender Zylinder, Kolben-∅ 80 ... 125 mm
Mehrstellungszylinder
Antriebszylinder für
Euro-X-Zangen
Festo Typ DNG-...-30-100-P-SA
VR: Vorhub rück
VV: Vorhub vor
AV: Arbeitshub vor
AR: Arbeitshub rück
-N- Durchmesser
80 ... 125 mm
-T- Hublänge
Arbeitshub
30 mm
Vorhub
100 mm
-L- Betriebsdruck
max. 12 bar
-Q- Temperaturbereich
–20 ... +80 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– Einsatz in Schweißzangen
– Verstärkte Kolbenstangen
Zubehör:
Als Zubehör sind Hub-
begrenzungsscheiben lieferbar.
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0546
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkender Zylinder, Kolben-∅ 80 ... 125 mm
Mehrstellungszylinder
DNG-...-30-100-P-SA
∅
[mm]
Vorhub
[mm]
Arbeitshub
[mm]
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
80 100 30 155776 DNG-80-30/100-P-SA M13 01 6132
100 100 30 173185 DNG-100-30/100-P-SA M13 01 6133
125 100 30 155678 DNG-125-30-100-P-SA –
Bestellbeispiel: Mehrstellungszylinder Kolben-∅ 125 mm, Vorhub 100 mm, Arbeitshub 30 mm:
155678 DNG-125-30-100-P-SA
1 Anschluss für Arbeitshub vor
2 Anschluss für Arbeitshub rück
3 Anschluss für Vorhub vor
4 Anschluss für Vorhub rück
∅
[mm]
AF B
∅
E E1 EE J1 KF
80 32 55 100 100 G¼ 30 M20x1,5
100 32 55 126 124 G¼ 30 M20x1,5
125 32 55 140 140 G¼ 40 M20x1,5
∅
[mm]
L2 MM
h8
PL PL1 TG VD WH ZJ ZM+ ß 1 ß 2
80 90 32 10 10 72 20 33 263 296 27 7
100 89 32 9 9 89 20 33 263 296 27 7
125 128 32 17 12 110 8 22 324 346 27 9
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 47
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkender Zylinder, Kolben-∅ 100 ... 125 mm
Mehrstellungszylinder
Antriebszylinder für
Euro-X-Zangen
Festo Typ D-...-60-30-PV2-SA
-N- Durchmesser
100 ... 125 mm
-T- Hublänge
Vorhub
60 mm
Arbeitshub
30 mm
-L- Betriebsdruck
max. 12 bar
-Q- Temperaturbereich
–20 ... +80 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– Dreistellungszylinder mit Vor-
und Arbeitshub
– Einsatz in Schweißzangen
– Verstärkte Kolbenstange
– Einstellbare Endlagen-
dämpfung im Arbeitshub
Zubehör:
Als Zubehör sind Hubbe-
grenzungsscheiben lieferbar.
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0548
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkender Zylinder, Kolben-∅ 100 ... 125 mm
Mehrstellungszylinder
D-...-60-30-PV2-SA
∅
[mm]
Vorhub
[mm]
Arbeitshub
[mm]
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
100 60 30 192867 D-100-60-30-PV2-SA M13 01 9820
125 60 30 194495 D-125-60-30-PV2-SA M13 01 9827
Bestellbeispiel: Mehrstellungszylinder Kolben-∅ 125 mm, Vorhub 60 mm, Arbeitshub 30 mm:
194495 D-125-60-30-PV2-SA
1 Einstellbare Endlagen-
dämpfung
RH = Rückhub
AH = Arbeitshub
VH = Vorhub
∅
[mm]
BG D4
∅
D5
∅
E J1 J2 J3 J4 MM
∅
h8
PL ß1
100 50 107 10 120 30 18 21 30 32 25 27
125 42 133 12 133 37 28 25 40 40 23 36
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 49
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkende Zylinder, Kolben-∅ 35 mm
Doppeltwirkender Zylinder
Einsatz als Ziehteilheber in Press-
werkzeugen
Festo Typ D-35-...-PP-SA
-N- Durchmesser
35 mm
-T- Hublänge
60, 75 und 90 mm
-L- Betriebsdruck
0,5 ... 10 bar
-Q- Temperaturbereich
–20 ... +80 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– Beidseitige Endlagendämpfung
duch Fixdrossel
– Hartvernickeltes Zylinderrohr
– Luftanschlüsse in der Kolben-
stange
Hub
[mm]
∅
[mm]
Festo Bestellbezeichnung
Teile-Nr. Typ
Opel-Material-Nr.
60 35 38 550 D-35-60-PP-SA M13 01 3578
75 35 194 038 D-35-75-PP-SA M13 01 8794
90 35 38 551 D-35-90-PP-SA M13 01 3579
Bestellbeispiel: Doppeltwirkender Zylinder Kolben-∅ 35 mm, Hub 60 mm: 38 550 D-35-60-PP-SA
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0550
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkende Zylinder, Kolben-∅ 35 mm
Doppeltwirkender Zylinder
D-35-...-PP-SA
1 Vorlauf
2 Rücklauf
3 um 360 ° drehbar
+ = zuzüglich Hublänge
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 51
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkende Zylinder, Kolben-∅ 50 mm und 63 mm
Doppeltwirkender Zylinder
Ausgleichszylinder für
Euro-X-Zangen
Festo Typ D-…-20-P-SA
-N- Durchmesser
50 mm und 63 mm
-T- Hublänge
20 mm
-L- Betriebsdruck
0,5 ... 12 bar
-Q- Temperaturbereich
–20 ... +80 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– Einsatz in Schweißzangen
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0552
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkende Zylinder, Kolben-∅ 50 mm und 63 mm
Doppeltwirkender-Zylinder
D-...-20-P-SA
∅
[mm]
Hub
[mm]
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
50 20 184809 D-50-20-P-SA M13 01 5644
63 20 526604 D-63-20-P-SA M13 01 5645
Bestellbeispiel: Doppeltwirkender Zylinder Kolben-∅ 50 mm, Hub 20 mm
184809 D-50-20-P-SA
∅
[mm]
B1 B2 D1
∅
D2 D3
H7
∅
D4 EE H1 H2
∅
h8
H3
+0,1
H4 L1 L2
50 67,6 ~32,4 20 M10 10 M4 G1/4 67,6 58 15 2,9 80,5 50,5
63 86,6 ~36,1 86,6 3,9 82,5 52,5
∅
[mm]
L3
+0,1
L4
+0,3
L5 L6 L7 L8 L9 T1 T2 W1 ß1
50 68,5 10 42 18 13,5 8 6 15 8 60° 17
63 70,5 10 44
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 53
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkende Zylinder, Kolben-∅ 32 mm und 40 mm
Doppeltwirkender Zylinder
Ausgleichszylinder für
Euro-C-Zangen
Festo Typ D-…-35-P-SA
-N- Durchmesser
32 mm und 40 mm
-T- Hublänge
35 mm
-L- Betriebsdruck
max.
12 bar
-Q- Temperaturbereich
–20 ... +80 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– Einsatz in Schweißzangen
– Anschlussseitig mit ein-
gepressten Isolierbuchsen
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0554
Zylinder nach Opel Norm, Material-Nr. M13 01 ...Doppeltwirkende Zylinder, Kolben-∅ 32 mm und 40 mm
Doppeltwirkender-Zylinder
D-...-35-P-SA
∅
[mm]
Hub
[mm]
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
32 35 183529 D-32-35-P-SA M13 01 5646
40 35 549219 D-40-35-P-SA M13 01 5647
Bestellbeispiel: Doppeltwirkender Zylinder Kolben-∅ 32 mm, Hub 35 mm
183529 D-32-35-P-SA
1 Isolierbuchse POM
∅
[mm]
B1 B2 B3 B4 D1
∅
D2
∅
D3 D4
∅
D5
∅
EE H1 H2
32 70 52 42 18 28 12 M8 8,2 11,5 G1/8 45 34,6
40 30 8,3
∅
[mm]
H3 H4 L1 L2 L3 L4 L5 L6 L7 T1 ß1 ß2
32 22,5 8 75 57 32 10 14 8 17 10 24 10
40 59 —
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 55
Steuereinheiten nach Opel NormInhaltsverzeichnis
Bezeichnung Festo Typ Seite
Reglerplatten
Reglerplatte
für Ausgleichszylinder 2-fach
RP VSPA 56
Reglerplatte
für Ausgleichszylinder 4-fach
RP VSPA-VSVA 58
Ventilblöcke
Ventilblock
für Euro C-45/C45HD-Zange
Steuerblock ISO15407 60
Ventilblock
für Euro X50/450-Zange und
X-1000-Zange
Steuerblock ISO5599 62
Ventilblock
für Euro X50/550-Zange
Steuerblock ISO5599 64
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0556
Reglerplatten nach Opel NormReglerplatte für Ausgleichszylinder 2-fach
Reglerplatte
für Ausgleichszylinder 2-fach
Festo Typ Reglerplatte RP VSPA
-L- Einspeisedruck (P1)
max. 12 bar
Einstellbereiche
1 ... 12 bar
Anschluß 14
2 ... 12 bar
-Q- Temperaturbereich
–10 ... +60 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– für Ausgleichszylinder
– 2-fach
– Stationärer Einsatz
Die Reglerplatte ist eine komplett
montierte, anschlussfertig Ein-
heit, bestehend aus:
– 1 Pneumatikventil
– 2 Regler
– 2 Manometer mit Sollwert-
zeiger
– 1 Schalldämpfer
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 57
Reglerplatten nach Opel NormReglerplatte für Ausgleichszylinder 2-fach
Reglerplatte
RP VSPA
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
1389050 RP VSPA M32 03 1442
Bestellbeispiel: Reglerplatte
1389050 RP VSPA
B1 H1 H2 L1 L2 L3
~84 ~95,1 10 87 66 10,5
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0558
Reglerplatten nach Opel NormReglerplatte für Ausgleichszylinder 4-fach
Reglerplatte
für Ausgleichszylinder 4-fach
Festo Typ Reglerplatte
RP VSPA-VSVA
-L- Einspeisedruck (P2)
max. 12 bar
Einstellbereiche
1 ... 12 bar
Anschluß 14
2 ... 12 bar
-Q- Temperaturbereich
–10 ... +60 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
– für Ausgleichszylinder
– 4-fach
– Einsatz auf Robotern
Die Reglerplatte ist eine komplett
montierte, anschlussfertig Ein-
heit, bestehend aus:
– 2 Pneumatikventile
– 2 Magnetventile
– 4 Regler
– 4 Manometer mit Sollwert-
zeiger
– 1 Schalldämpfer
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 59
Reglerplatten nach Opel NormReglerplatte für Ausgleichszylinder 4-fach
Reglerplatte
RP VSPA-VSVA
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
1375452 RP VSPA-VSVA M32 03 1504
Bestellbeispiel: Reglerplatte
1375452 RP VSPA-VSVA
B1 B2 B3 H1 L1 L2 L3
~159,1 78 5,7 ~117,8 ~141,6 110 5
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0560
Ventilblöcke nach Opel NormVentilblock für Euro C-45 / C45HD-Zange
Ventilblock
für Euro C-45 / C45HD-Zange
Festo Typ Steuerblock ISO15407
-L- Einspeisedruck (E1)
max. 8 bar
-Q- Temperaturbereich
5 ... 50 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
Der Ventilblock ist eine komplett
montierte, anschlussfertig Ein-
heit, bestehend aus:
– 1 Ventilblock
– 3 Magnetventile
– 2 Schalldämpfer
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 61
Ventilblöcke nach Opel NormVentilblock für Euro C-45 / C45HD-Zange
Ventilblock
Steuerblock ISO15407
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
1388296 Steuerblock ISO15407 M32 09 1599
Bestellbeispiel: Steuerblock
1388296 Steuerblock ISO15407
B1 B2 B3 B4 H1 H2 L1 L2 L3 L4 L5
~128 71,5 44,5 17,5 ~98,8 26 ~122,5 69 48 27 6
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0562
Ventilblöcke nach Opel NormVentilblock für Euro X50/450-Zange und X-1000 Zange
Ventilblock
für Euro X50/450-Zange und
X-1000 Zange
Festo Typ Steuerblock ISO5599
-L- Einspeisedruck (E1)
max. 10 bar
-Q- Temperaturbereich
5 ... 50 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
Der Ventilblock ist eine komplett
montierte, anschlussfertig Ein-
heit, bestehend aus:
– 1 Ventilblock
– 3 Magnetventile
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 63
Ventilblöcke nach Opel NormVentilblock für Euro X50/450-Zange und X-1000 Zange
Ventilblock
Steuerblock ISO5599
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
1388209 Steuerblock ISO5599 M32 09 1293
Bestellbeispiel: Steuerblock
1388209 Steuerblock ISO5599
B1 H1 H2 L1 L2 L3 L4
~152 ~92,3 22 ~138,1 26,5 26,5 13,5
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0564
Ventilblöcke nach Opel NormVentilblock für Euro X50/550-Zange
Ventilblock
für Euro X50/550-Zange
Festo Typ Steuerblock ISO5599
-L- Einspeisedruck (E1)
max. 10 bar
-Q- Temperaturbereich
5 ... 50 °C
– Medium:
gefilterte Druckluft – geölt
oder ungeölt
Der Ventilblock ist eine komplett
montierte, anschlussfertig Ein-
heit, bestehend aus:
– 1 Ventilblock
– 2 Magnetventile
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 65
Ventilblöcke nach Opel NormVentilblock für Euro X50/550-Zange
Ventilblock
Steuerblock ISO5599
Festo Bestellbezeichnung
Teile-Nr Typ
Opel-Material-Nr.
1388476 Steuerblock ISO5599 M32 09 1294
Bestellbeispiel: Steuerblock
1388476 Steuerblock ISO5599
B1 H1 H2 L1 L2 L3 L4
~109 ~92,3 22 ~138,1 26,5 26,5 13,5
de
Festo AG & Co. KG – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – 2012/0566
Engineering Tools
Schon die Anlagenkonzeption
stellt die Weichen für den effizien-
ten Einsatz von Energie und den
schnellen Return on Investment.
In der Engineering-Phase lassen
sich überraschende energetische
Einsparpotenziale realisieren –
durch den Einsatz hocheffizienter
Auswahl- und Dimensionierungs-
Software-Tools. Sowohl im Be-
reich elektrischer als auch pneu-
matischer Antriebssysteme. Mit
Engineering Tools von Festo ver-
meiden Sie eine Überdimensio-
nierung Ihrer Komponenten/Sy-
steme. Gleichzeitig stimmen die
Software Tools alle Komponenten
und Systeme optimal auf Ihre Ap-
plikation ab. Egal, welche Anfor-
derungen: Festo liefert als Kom-
plettanbieter für jedes Anwen-
dungsgebiet die ideale Lösung.
Positioning Drives Welcher elektromechanische
Linearantrieb erfüllt Ihre Aufgabe
am besten? Geben Sie die Daten
Ihrer Anwendung wie Positions-
werte, Nutzmasse und Einbau-
lage ein und die Software schlägt
Ihnen mehrere optimale Lösun-
gen vor.
Pneumatische Dimensionierung
mit ProPneu
Perfekte Simulationen ersetzen
teure Realitätstests! ProPneu un-
terstützt Sie bei der Auswahl und
Konfiguration der gesamten
pneumatischen Steuerungskette
wie ein Expertensystem. Wird ein
Parameter verändert, passt das
Programm automatisch alle wei-
teren an.
Vakuumauswahl Welcher Saugnapf auf welche
Oberfläche bei welcher Bewe-
gung? Nicht testen – berechnen!
Über dieses Software Tool lassen
sich sogar lineare oder rotative
Bewegungen unterscheiden.
Schlauchauswahl Einfach Parameter wie zum Bei-
spiel Arbeitsdruck, Chemikalien
und gewünschte Beständigkeit
gegen Reiniger eingeben und
schon berechnet Ihnen das Pro-
gramm den für Ihre Anwendung
passenden Schlauch.
Luftverbrauch Ermitteln Sie schnell und bequem
den Luftverbrauch Ihrer Anlage.
Einfach alle Antriebe und Schläu-
che erfassen, Zykluszeiten und
Arbeitsdruck einstellen und
schon wird der Luftverbrauch pro
Minute und pro Tag errechnet. In-
klusive des Exports der Eingabe-
tabelle samt Ergebnis direkt nach
Excel.
de
2012/05 – Änderungen vorbehalten/Subject to change/Reservado el dereho de modificación – Festo AG & Co. KG 67
Engineering Tools
Ein sicherer Griff ist eine Frage
der richtigen Berechnung. In die-
sem Falle von Gewicht, Bewe-
gungsrichtung, Abständen usw.
Das Tool präsentiert sofort, wel-
cher der parallelen, radialen, Win-
kel- oder 3-Punkt-Greifer in wel-
cher Dimensionierung Ihre Anfor-
derung optimal erfüllt.
Greiferauswahl
Ob schräg oder senkrecht, im
Bogen oder geradeaus, ob als
Hebel oder Scheibe: Alle Fälle
von gedämpften Bewegungen
werden berücksichtigt. Das Tool
schlägt immer den besten
Stoßdämpfer vor.
Stoßdämpferauswahl
Das Jonglieren mit Bleistift und
Taschenrechner gehört für Sie der
Vergangenheit an. Egal, ob Schei-
ben, Quader, Ansteckflansche,
Greifer, usw.: Dieses Tool berech-
net alle Massenträgheitsmo-
mente.
Abspeichern, übernehmen oder
drucken und fertig.
Massenträgheitsmoment
Der schnelle Softstop macht bei-
nahe Unmögliches möglich. Eine
bis zu 30%ige Verkürzung der
Verfahrzeit bei pneumatischen
Antrieben und eine enorme Re-
duktion der Erschütterungen. Das
Auswahlprogramm leistet alle
notwendigen Berechnungen.
Softstop
Linearantriebe von Festo sind
bekannt für viel Kraft auf wenig
Raum. Ihre optimale Konfigura-
tion ermittelt Ihnen dieses Tool.
Sie geben die Projektparameter
wie Masse oder Kraft, Einbaulage
und Weg vor.
Führungsberechnung für
pneumatische Linearantriebe
de
Festo AG & Co. KG – Automotive range – Subject to change – 2012/05
Pneumatics for the automotive
industry
Opel
05/2012 issue
All technical data applies at the time
of going to print.
All texts, representations, illustra-
tions and drawings included in this
catalogue are the intellectual prop-
erty of Festo AG & Co. KG and are pro-
tected by copyright law. All rights re-
served, including translation rights.
No part of this publication may be re-
produced or transmitted in any form
or by any means, electronic, mechan-
ical, photocopying or otherwise, with-
out the prior written permission of
Festo AG & Co. KG.
All technical data subject to change
according to technical update.
Festo AG & Co. KG
P.O. Box
73726 Esslingen
Ruiter Straße 82
73734 Esslingen
Germany
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 1
Automotive RangeOverview
Page
ISO cylinders 2
ISO valves 23
Other products 36
Special designs 55
Engineering software 66
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/052
ISO cylinders to Opel standardPiston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
ContentsDesignation Festo type Opel standard
Material no.
Page
Tie rod cylinder
for position sensing and ad-
justable end-position
cushioning
DOG-...-PPV-A M13 01... 4
Basic cylinder with attached
trunnion mounting
DOGZK-... M13 01... 4
Cylinder accessories
Cylinder sensor
inductive
SMTSO-...
SMBT-1
J06 13... 10
Foot mounting HNG-... M13 91... 12
Flange mounting FNG-... M13 91... 13
Trunnion block LNZG-... M13 91... 14
Swivel flange SNGB-... M13 91... 15
Clevis foot mounting, fixed LNG-...
LN-...
M13 91... 16
Clevis foot mounting
with spherical bearing
LSN-... M13 91... 17
Swivel flange SNG-... M13 91... 18
Clevis foot mounting,
spherical
LSNG-... M13 91... 19
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 3
ISO cylinders to Opel standardPiston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
ContentsDesignation Festo type Opel standard
Material no.
Page
Rod eye SGS-... M37 23... 20
Rod clevis SG-... M13 91... 21
Self-aligning rod coupler FK-... M13 91... 22
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/054
ISO cylinders to Opel standard, material no. M13 01...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
DOG-... DOGZK-...
Double-acting cylinderFesto type DOG
with trunnion,
Type E
DOGZK
-N- Diameters
32 ... 320 mm
-T- Stroke lengths
25 ... 500 mm
-L- Max. operating pressure
Piston∅ 32 ... 125 mm:
12 bar
Piston∅ 160 ... 320 mm:
10 bar
-Q- Temperature range
–20 ... +80 °C
– Medium:
Filtered compressed air
lubricated or unlubricated
Basic cylinder without mounting
attachments
These cylinders comply with the fol-
lowing standards:
ISO 6431 (international)
DIN ISO 6431 and
VDMA 24 562 (Germany)
NF E 49 003.1 (France)
UNI 10 290 (Italy)
DIN
NF E 49 003.1UNI 10 290
DOG-...-PPV-ATie rod cylinder for position sensing
and with adjustable end-position
cushioning
DOGZK-...-PPV-A
Tie rod cylinder with trunnion, for
position sensing and adjustable end-
position cushioning
Trunnions are mounted at the centre
of the cylinder as standard equip-
ment.
Mounting at other positions is
possible. Dimension XG must be
specified as desired (see page 8).
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 5
ISO cylinders to Opel standard, material no. M13 01...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Mounting options
Basic cylinder installation
Mounting at front Mounting at rear
Accessories
Installation options with mounting
attachments
Foot mounting
HNG-...
Flange mounting
FNG-...
Additional mounting components
on the piston rod
Rod eye
SGS-...
front rear
Trunnion block
LNZG-...
Swivel flange
SNGB-...
Rod clevis
SG-...
Clevis foot mounting, fixed
LNG-...
LN-...
Clevis foot mounting with
spherical bearing
LSN-...
Self-aligning rod coupler
FK-...
Swivel flange
SNG-...
Clevis foot mounting, spherical
LSNG-...
Cylinder sensorSMTSO-1-PS-S-LED-24
Mounting kit for cylinder switches
SMBT-1
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/056
ISO cylinders to Opel standard, material no. M13 01...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Double-acting cylinderDOG-...-PPV-A
∅ Opel material no. M13 01...
[mm]
Stroke length
[mm]
Festo order code
Part No. Type
25 50 80 100 125
32
40
50
63
80
100
125
160
200
250
320
4000
4011
4022
4033
4044
4055
4066
4077
4088
4099
4110
4001
4012
4023
4034
4045
4056
4067
4078
4089
4100
4111
4002
4013
4024
4035
4046
4057
4068
4079
4090
4101
4112
4003
4014
4025
4036
4047
4058
4069
4080
4091
4102
4113
4004
4015
4026
4037
4048
4059
4070
4081
4092
4103
4114
164 430 DOG-32-...-PPV-A
164 431 DOG-40-...-PPV-A
164 432 DOG-50-...-PPV-A
164 433 DOG-63-...-PPV-A
164 434 DOG-80-...-PPV-A
164 435 DOG-100-...-PPV-A
164 436 DOG-125-...-PPV-A
164 437 DOG-160-...-PPV-A
164 438 DOG-200-...-PPV-A
164 439 DOG-250-...-PPV-A
164 440 DOG-320-...-PPV-A
∅ Opel material no. M13 01...
[mm]
Stroke length
[mm]
Festo order code
Part No. Type
160 200 250 320 400 500
32
40
50
63
80
100
125
160
200
250
320
4005
4016
4027
4038
4049
4060
4071
4082
4093
4104
4115
4006
4017
4028
4039
4050
4061
4072
4083
4094
4105
4116
4007
4018
4029
4040
4051
4062
4073
4084
4095
4106
4117
4008
4019
4030
4041
4052
4063
4074
4085
4096
4107
4118
4009
4020
4031
4042
4053
4064
4075
4086
4097
4108
4119
4010
4021
4032
4043
4054
4065
4076
4087
4098
4109
4120
164 430 DOG-32-...-PPV-A
164 431 DOG-40-...-PPV-A
164 432 DOG-50-...-PPV-A
164 433 DOG-63-...-PPV-A
164 434 DOG-80-...-PPV-A
164 435 DOG-100-...-PPV-A
164 436 DOG-125-...-PPV-A
164 437 DOG-160-...-PPV-A
164 438 DOG-200-...-PPV-A
164 439 DOG-250-...-PPV-A
164 440 DOG-320-...-PPV-A
Order example: Piston∅ 80 mm, 160 mm stroke: 164 434 M13 01 4049
Opel designation for cylinder with 80 mm diameter and 160 mm stroke:
Basic cylinder 80 x 160 VDMA 24 562 M13 01 4049
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 7
ISO cylinders to Opel standard, material no. M13 01...Piston∅ 32 ... 200 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Double-acting cylinderwith trunnion, type E
DOGZK-...-PPV-A
∅ Opel material no. M13 01...
[mm]
Stroke length
[mm]
Festo order code
Part No. Type
25 50 80 100 125
32
40
50
63
80
100
125
160
200
1484
1495
1506
1517
1528
1539
1550
1561
1572
1485
1496
1507
1518
1529
1540
1551
1562
1573
1486
1497
1508
1519
1530
1541
1552
1563
1574
1487
1498
1509
1520
1531
1542
1553
1564
1575
1488
1499
1510
1521
1532
1543
1554
1565
1576
164 441 DOGZK-32-...-PPV-A
164 442 DOGZK-40-...-PPV-A
164 443 DOGZK-50-...-PPV-A
164 444 DOGZK-63-...-PPV-A
164 445 DOGZK-80-...-PPV-A
164 446 DOGZK-100-...-PPV-A
164 447 DOGZK-125-...-PPV-A
164 448 DOGZK-160-...-PPV-A
164 449 DOGZK-200-...-PPV-A
∅ Opel material no. M13 01...
[mm]
Stroke length
[mm]
Festo order code
Part No. Type
160 200 250 320 400 500
32
40
50
63
80
100
125
160
200
1489
1500
1511
1522
1533
1544
1555
1566
1577
1490
1501
1512
1523
1534
1545
1556
1567
1578
1491
1502
1513
1524
1535
1546
1557
1568
1579
1492
1503
1514
1525
1536
1547
1558
1569
1580
1493
1504
1515
1526
1537
1548
1559
1570
1581
1494
1505
1516
1527
1538
1549
1560
1571
1582
164 441 DOGZK-32-...-PPV-A
164 442 DOGZK-40-...-PPV-A
164 443 DOGZK-50-...-PPV-A
164 444 DOGZK-63-...-PPV-A
164 445 DOGZK-80-...-PPV-A
164 446 DOGZK-100-...-PPV-A
164 447 DOGZK-125-...-PPV-A
164 448 DOGZK-160-...-PPV-A
164 449 DOGZK-200-...-PPV-A
Order example: Piston∅ 80 mm, 160 mm stroke: 164 445 M13 01 1533
Opel designation for a type E cylinder with 80 mm diameter and 160 mm stroke:
Cylinder E 80 x 160 VDMA 24 562 M13 01 1533
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/058
ISO cylinders to Opel standard, material no. M13 01...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Double-acting cylinderDOG-...-PPV-A
DOG-32 ... 63 DOG-80 ... 320
DOGZK-...-PPV-A
1 Socket head screws with internal
threads for mounting attach-
ments
2 Regulating screw for adjustable
end-position cushioning
3 From∅ 125 with additional
rods for mounting the cylinder
sensors
+ = plus stroke length
+½ = plus half stroke length
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 9
ISO cylinders to Opel standard, material no. M13 01...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Double-acting cylinderDOG-...-PPV-A
DOGZK-...-PPV-A
∅
[mm]
AM B
∅
d11
BG C2 C3 D4
∅
D5
∅
E EE J2 J3 KK
32 22 30 17 71 86 37 6 50 Gx 7 – M10x1.25
40 24 35 16.5 87 105 45 6 55 G¼ 9.5 2.5 M12x1.25
50 32 40 17 99 117 55 8 65 G¼ 12 5.5 M16x1.5
63 32 45 19.5 116 136 68 8 75 Gy 14 6 M16x1.5
80 40 45 20 136 156 86 10 100 Gy 15 7 M20x1.5
100 40 55 20 164 189 107 10 120 G½ 13 8 M20x1.5
125 54 60 25 192 217 133 12 145 G½ 13 8 M27x2
160 72 65 24 245 280 168 16 186 G¾ 22 22 M36x2
200 72 75 24 295 330 210 16 230 G¾ 22 22 M36x2
250 84 90 25.5 – – 254 18 270 G1 25 25 M42x2
320 96 110 28.5 – – 325 22 340 G1 30 30 M48x2
∅
[mm]
L1 L2 L7 MM
∅
f8
PL RT TD
∅
e9
TG TK TL
32 19 94 ±0.4 5.8 12 8.8 M6 12 32.5 20 12
40 21.5 105 ±0.7 5.3 16 11 M6 16 38 25 16
50 28.5 106 ±0.7 2 20 17.5 M8 16 46.5 28 16
63 28.5 121 ±0.8 5 20 18 M8 20 56.5 30 20
80 34.5 128 ±0.8 8 25 17 M10 20 72 32 20
100 37.5 138 ±0.8 13 25 18 M10 25 89 38 25
125 46 160 ±1 14 32 18 M12 25 110 44 25
160 55 180 ±1.1 – 40 25 M16 32 140 48 32
200 65 180 ±1.6 – 40 28 M16 32 175 48 32
250 67 200 ±2 – 50 31 M20 – 220 – –
320 82 220 ±2 – 63 31 M24 – 240 – –
∅
[mm]
TM UW VA VD WH XG XJ XV ZJ ß1 ß3 ß4
32 50 68 4 10.5 26 62 84 73 120 10 6 –
40 63 72 4 10.5 30 69 96 82.5 135 13 6 –
50 75 86 4 12 37 80 100 90 143 17 8 –
63 90 98 4 12.5 37 87 108 97.5 158 17 8 –
80 110 110 4 16.5 46 101 119 110 174 22 – 17
100 132 136 4 15.5 51 112 128 120 189 22 – 17
125 160 160 6 20.5 65 136 154 145 225 27 – 19
160 200 200 6 – 80 155 185 170 260 36 – 32
200 250 240 6 – 95 165 205 185 275 36 – 32
250 – – 10 – 105 – – – 305 46 – 36
320 – – 10 – 120 – – – 340 55 – 46
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0510
Cylinder accessories to Opel standard, material no. J06 13...Cylinder sensors for piston∅ 32 ... 100 mm
SMTSO SMBT
Cylinder sensor, inductivewith yellow and green LED, protective
circuit, immune to AC welding fields
SMTSO-1-PS-S-LED-24
Colour coding
BK = black
BN = brown
BU = blue
-P- Voltage
24 V DC, 250 V AC
-Q- Temperature range
–25 ... +70 °C
– Max. switching current:
200 mA
– Switching voltage:
10 ... 30 V DC
– Switching output:
PNP
– Degree of protection per
DIN 40 050:
IP 67
– Reproducible switching accuracy:
± 0.1 mm
This cylinder sensor generates an
electrical signal when it approaches a
magnetic field (e.g. permanent
magnet on the cylinder piston).
Switching status is indicated with the
yellow LED. Green LED indicates
power-on.
Accessories:
Mounting kit
(must be ordered separately)
Festo type SMBT-1
Cylinder sensor AccessoriesOpel material no. Festo order code
Part No. Type
Opel material no. Festo order code
Part No. Type
J06 13 0891 30 441 SMTSO-1-PS-S-LED-24 J06 91 0537 150 002 SMBT-1
Order example: Cylinder sensor, immune to welding field: 30 441 J06 13 0891
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 11
Cylinder accessories to Opel standard, material no. J06 13...Cylinder sensors for piston∅ 32 ... 100 mm
Plug sockets with cableStraight sockets Angled socketsCable length
[m]
Part No. Type Part No. Type
2.5 159 428 SIM-M12-3GD-2.5-PU 159 430 SIM-M12-3WD-2.5-PU For detailed product informationsee DVD and
www.festo.com/catalogue/sim3 30 450 SIM-M12-RS-3GD-3 30 451 SIM-M12-RS-3WD-3
5 159 429 SIM-M12-3GD-5-PU 159 431 SIM-M12-3WD-5-PU
1 Green LED – power ON
2 Yellow LED – switching status
3 Mounting kit SMBT-1
4 Installation space for socket
5 Theoretical switching point
Cylinder sensorSMTSO-1-PS-S-LED-24
1 Cylinder sensor SMTSO-1
Mounting kitSMBT-1
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0512
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Foot mountingFesto type HNG
Scope of delivery:
2 feet and 4 mounting screws
∅
[mm]
Festo order code
Part No. Type
Opel material no.
32
40
50
63
80
100
125
160
200
250
320
32 947 HNG-32
32 948 HNG-40
32 949 HNG-50
32 950 HNG-63
32 951 HNG-80
32 952 HNG-100
32 953 HNG-125
34 476 HNG-160
34 477 HNG-200
157 510 HNG-250
157 511 HNG-320
M13 91 1662
M13 91 1663
M13 91 1664
M13 91 1665
M13 91 1666
M13 91 1667
M13 91 1668
M13 91 1669
M13 91 1670
M13 91 1671
M13 91 1672
Order example: Foot mounting for piston∅ 50 mm: 32 949 M13 91 1664
Opel designation for foot mounting for piston∅ 50 mm:
Foot mounting 50 VDMA 24 562 M13 91 1664
+ = plus stroke length
∅
[mm]
Socket head
screw
DIN 912
AB
∅
H14
AH AO AT AU SA TR US XA
32 M6x18 7 32 6.5 4 24 142 32 45 144
40 M6x18 10 36 9 4 28 161 36 54 163
50 M8x20 10 45 9.5 5 32 170 45 64 175
63 M8x20 10 50 12.5 5 32 185 50 75 190
80 M10x20 12 63 15 6 41 210 63 93 215
100 M10x20 14.5 71 17.5 6 41 220 75 110 230
125 M12x25 16.5 90 22 8 45 250 90 131 270
160 M16x30 18.5 115 20 10 60 300 115 169 320
200 M16x30 24 135 30 12 70 320 135 214 345
250 M20x40 28 165 35 20 75 350 165 270 380
320 M24x45 35 185 40 23 85 390 200 340 425
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 13
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Scope of delivery:
1 flange and 4 mounting screws
Flange mountingFesto type FNG
front rear
∅
[mm]
Festo order code
Part No. Type
Opel material no.
32
40
50
63
80
100
125
160
200
250
320
32 940 FNG-32
32 941 FNG-40
32 942 FNG-50
32 943 FNG-63
32 944 FNG-80
32 945 FNG-100
32 946 FNG-125
34 478 FNG-160
34 479 FNG-200
157 508 FNG-250
157 509 FNG-320
M13 91 1640
M13 91 1641
M13 91 1642
M13 91 1643
M13 91 1644
M13 91 1645
M13 91 1646
M13 91 1647
M13 91 1648
M13 91 1649
M13 91 1650
Order example: Flange mounting for piston∅ 50 mm: 32 942 M13 91 1642
Opel designation for flange mounting for piston∅ 50 mm:
Flange mounting 50 VDMA 24 562 M13 91 1642
+ = plus stroke length
∅
[mm]
Socket head
screw
DIN 912
E FB
∅
MF R TF UF W ZF
32 M6x18 45 7 10 32 64 80 16 130
40 M6x18 54 9 10 36 72 90 20 145
50 M8x20 65 9 12 45 90 110 25 155
63 M8x20 75 9 12 50 100 120 25 170
80 M10x20 93 12 16 63 126 150 30 190
100 M10x20 110 14 16 75 150 175 35 205
125 M12x25 140 16 20 90 180 220 45 245
160 M16x30 180 18 20 115 230 280 60 280
200 M16x30 220 22 25 135 270 320 70 300
250 M20x30 270 26 25 165 330 390 80 330
320 M24x40 340 33 30 200 400 470 90 370
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0514
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Trunnion blockFesto type LNZG
For supporting the trunnion
Scope of delivery:
2 trunnion blocks
∅
[mm]
Festo order code
Part No. Type
Opel material no.
32
40/50
63/80
100/125
160/200
250
320
32 959 LNZG-32
32 960 LNZG-40/50
32 961 LNZG-63/80
32 962 LNZG-100/125
35 780 LNZG-160/200
157 516 LNZG-250
157 517 LNZG-320
M13 91 2310
M13 91 2311
M13 91 2312
M13 91 2313
M13 91 2314
M13 91 2315
M13 91 2316
Order example: Trunnion block for piston∅ 50 mm: 32 960 M13 91 2311
Opel designation for trunnion block set for piston∅ 50 mm:
Trunnion blocks 40/50 VDMA 24 562 M13 91 2311
∅
[mm]
CR
∅
DA
∅
H13
FK
∅
FN FS H1 HB
∅
H13
KE NH TH
±0.1
UL
32 12 D11 11 15 ±0.1 30 10.5 15 6.6 6.8 18 32 46
40 16 D11 15 18 ±0.1 36 12 18 9 9 21 36 55
50 16 D11 15 18 ±0.1 36 12 18 9 9 21 36 55
63 20 D11 18 20 ±0.1 40 13 20 11 11 23 42 65
80 20 D11 18 20 ±0.1 40 13 20 11 11 23 42 65
100 25 D11 20 25 ±0.1 50 16 24.5 14 13 28.5 50 75
125 25 D11 20 25 ±0.1 50 16 24.5 14 13 28.5 50 75
160 32 D11 26 30 ±0.2 60 22.5 36 18 17 40 60 92
200 32 D11 26 30 ±0.2 60 22.5 36 18 17 40 60 92
250 40 G7 33 35 ±0.2 70 27.5 45 22 21.5 50 90 140
320 50 G7 40 40 ±0.2 80 32.5 55 26 25.5 60 100 150
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 15
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
For clevis foot mountings LN, LNG and
LSN-...
Scope of delivery:
1 swivel flange, 1 pivot pin with lock
and 4 mounting screws
Swivel flangeFesto type SNGB
∅
[mm]
Festo order code
Part No. Type
Opel material no.
32
40
50
63
80
100
125
160
200
250
320
34 540 SNGB-32
34 541 SNGB-40
34 542 SNGB-50
34 543 SNGB-63
34 544 SNGB-80
34 545 SNGB-100
34 546 SNGB-125
34 547 SNGB-160
562 455 SNGB-200-B
157 512 SNGB-250
157 513 SNGB-320
M13 91 1651
M13 91 1652
M13 91 1653
M13 91 1654
M13 91 1655
M13 91 1656
M13 91 1657
M13 91 1658
M13 91 1659
M13 91 1660
M13 91 1661
Order example: Swivel flange for piston∅ 50 mm: 34 542 M13 91 1653
Opel designation for swivel flange for piston∅ 50 mm:
Swivel flange 50 VDMA 24 562 M13 91 1653
+ = plus stroke length
∅
[mm]
Socket head
screw
DIN 912
CB
H14
CD
∅
FL L ML MR UB
h14
XC
32 M6x18 26 10 22 13 55 10 45 142
40 M6x18 28 12 25 16 63 12 52 160
50 M8x20 32 12 27 16 71 12 60 170
63 M8x20 40 16 32 21 83 16 70 190
80 M10x20 50 16 36 22 103 16 90 210
100 M10x20 60 20 41 27 127 20 110 230
125 M12x25 70 25 50 30 148 25 130 275
160 M16x30 90 30 55 35 188 25 170 315
200 M16x30 90 30 60 35 188 25 170 335
250 M20x30 110 40 70 47 231 40 200 375
320 M24x40 120 45 80 52 253 45 220 420
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0516
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Clevis foot mounting, fixedFesto type LNG, LN
For swivel flange SNGB-...
Scope of delivery:
1 clevis foot mounting
∅
[mm]
Festo order code
Part No. Type
Opel material no.
32
40
50
63
80
100
125
160
200
250
320
33 890 LNG-32
33 891 LNG-40
33 892 LNG-50
33 893 LNG-63
33 894 LNG-80
33 895 LNG-100
33 896 LNG-125
9 037 LN-160
33 898 LNG-200
9 039 LN-250
9 040 LN-320
M13 91 1101
M13 91 1102
M13 91 1103
M13 91 1104
M13 91 0924
M13 91 1105
M13 91 1106
M13 91 1107
M13 91 1108
M13 91 1109
M13 91 1358
Order example: Clevis foot mounting, fixed, for piston∅ 50 mm: 33 892 M13 91 1103
Opel designation for fixed clevis foot mounting for piston∅ 50 mm:
Clevis foot mounting 50 VDMA 24 562 M13 91 1103
∅
[mm]
BR BT CK
∅
EB
∅
H13
EM GL HB
∅
H13
OF PH RA TE UL UR
32 10 8 10 D11 – 25.8 –0.4 21 5.5 – 32 18 38 51 31
40 11 10 12 D11 – 27.8 –0.4 24 5.5 – 36 22 41 54 35
50 12 12 12 D11 – 31.8 –0.4 33 6.5 – 45 30 50 65 45
63 14.5 12 16 D11 15 40 c11 37 6.6 10.8 50 35 52 67 51
80 14.5 14 16 D11 20 50 c11 47 9 12.7 63 40 66 86 60
100 18.5 15 20 D11 20 60 c11 55 9 13.7 71 50 76 96 70
125 22 20 25 D11 20 70 c11 70 11 18.6 90 60 94 124 90
160 31 25 30 H8 20 90 c11 97 14 23.6 115 88 118 156 126
200 31 30 30 D11 26 90 c11 105 18 28.5 135 90 122 162 130
250 38.5 35 40 H8 33 110 c11 128 22 33.5 165 110 150 200 160
320 44.5 40 45 H8 40 120 c11 150 26 38.3 200 122 170 234 186
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 17
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
For swivel flange SNGB-...
Scope of delivery:
1 clevis foot mounting and 2 bushes
Clevis foot mountingwith spherical bearing
Festo type LSN
∅
[mm]
Festo order code
Part No. Type
Opel material no.
32
40
50
63
80
100
125
160
200
250
320
5 561 LSN-32
5 562 LSN-40
5 563 LSN-50
5 564 LSN-63
5 565 LSN-80
5 566 LSN-100
6 987 LSN-125
6 988 LSN-160
6 989 LSN-200
6 990 LSN-250
6 991 LSN-320
M13 91 1223
M13 91 1359
M13 91 1287
M13 91 1285
M13 91 1286
M13 91 1360
M13 91 1361
M13 91 1362
M13 91 1363
M13 91 1364
M13 91 1365
Order example: Clevis foot mounting with spherical bearing for piston∅ 50 mm: 5 563 M13 91 1287
Opel designation for spherical clevis foot mounting for piston∅ 50 mm:
Clevis foot mounting 50 VDMA 24 562 M13 91 1287
∅
[mm]
BR BT CK
∅
H7
EB
∅
EM GL HB
∅
LE OF PH RA TE UL UR
32 13 8 10 10 25.8 21 5.5 16 4.5 32 18 38 51 31
40 15 10 12 10 27.8 24 5.5 20 4.3 36 22 41 54 35
50 15 12 12 11 31.8 33 6.6 22 5.2 45 30 50 65 45
63 20 12 16 11 39.8 37 6.6 30 5.2 50 35 52 67 50
80 20 14 16 15 49.8 47 9 31 5 63 40 66 86 60
100 24 15 20 15 59.8 55 9 38 6 71 50 76 96 70
125 33 20 25 22 69.8 70 11 – 18 90 60 94 124 90
160 36 28 30 26 89.8 97 13.5 – 22 115 88 118 156 126
200 36 30 30 30 89.8 105 16 – 27 135 90 122 162 130
250 43 35 40 40 109.5 128 22 – 32 165 110 150 200 160
320 54 40 45 48 119.8 150 26 – 37 200 122 170 234 186
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0518
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 200 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Swivel flangeFesto type SNG
For clevis foot mounting LSNG-...
Scope of delivery:
1 swivel flange, 1 pivot pin with lock
and 4 mounting screws
∅
[mm]
Festo order code
Part No. Type
Opel material no.
32
40
50
63
80
100
125
160
200
32 968 SNG-32
32 969 SNG-40
32 970 SNG-50
32 971 SNG-63
32 972 SNG-80
32 973 SNG-100
32 974 SNG-125
152 597 SNG-160
152 598 SNG-200
M13 91 1673
M13 91 1674
M13 91 1675
M13 91 1676
M13 91 1677
M13 91 1678
M13 91 1679
M13 91 1680
M13 91 1681
Order example: Swivel flange for piston∅ 50 mm: 32 970 M13 91 1675
Opel designation for swivel flange for piston∅ 50 mm:
Swivel flange 50 VDMA 24 562 M13 91 1675
1 The pivot pin is secured against
rotation with a dowel pin.
+ = plus stroke length
∅
[mm]
Socket head
screw
DIN 912
CG
H14
CP
d12
EK
∅
FL L SR XC
32 M6x18 14 34 10 22 13 11 142
40 M6x18 16 40 12 25 16 13 160
50 M8x20 21 45 16 27 16 15 170
63 M8x20 21 51 16 32 21 18 190
80 M10x20 25 65 20 36 22 20 210
100 M10x20 25 75 20 41 27 22 230
125 M12x25 37 97 30 50 30 26 275
160 M16x30 43 122 35 55 35 32 315
200 M16x30 43 122 35 55 35 32 335
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 19
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 200 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
For swivel flange SNG-...
Scope of delivery:
1 clevis foot mounting
Clevis foot mounting, sphericalFesto type LSNG
∅
[mm]
Festo order code
Part No. Type
Opel material no.
32
40
50
63
80
100
125
160
200
31 740 LSNG-32
31 741 LSNG-40
31 742 LSNG-50
31 743 LSNG-63
31 744 LSNG-80
31 745 LSNG-100
31 746 LSNG-125
152 599 LSNG-160
152 600 LSNG-200
M13 91 1684
M13 91 1685
M13 91 1686
M13 91 1687
M13 91 1688
M13 91 1689
M13 91 1690
M13 91 1691
M13 91 1692
Order example: Sperical clevis foot mounting for piston∅ 50 mm: 31 742 M13 91 1686
Opel designation for spherical clevis foot mounting for piston∅ 50 mm:
Clevis foot mounting 50 VDMA 24 562 M13 91 1686
∅
[mm]
BR BT CN
∅
EB
∅
EN EU GL HB
∅
LE OF PH RA TE UL UR
32 15 10 10 11 14 10.5 21 6.6 16 9 32 18 38 51 31
40 17 10 12 11 16 12 24 6.6 20 9 36 22 41 54 35
50 20 12 16 14 21 15 33 9 24 11 45 30 50 65 45
63 22 12 16 14 21 15 37 9 27 11 50 35 52 67 50
80 27 14 20 17 25 18 47 11 31 12.5 63 40 66 86 60
100 29 15 20 17 25 18 55 11 38 13.5 71 50 76 96 70
125 39 20 30 19 37 25 70 14 50 18.5 90 60 94 124 90
160 42 28 35 20 43 28 97 14 45 25.5 115 88 118 156 126
200 42 35 35 26 43 28 97 18 45 31.8 135 88 122 162 130
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0520
Cylinder accessories to Opel standard, material no. M37 23...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Rod eyeFesto type SGS
Scope of delivery:
1 rod eye with hex nut per DIN 439
Per DIN 648 dimensional series K
with hex nut per DIN 439
Rod eyes are maintenance-free due to
a material combination of steel and
PTFE-bronze in the swivel bearing.
∅
[mm]
Piston rod thread Festo order code
Part No. Type
Opel material no.
32
40
50/63
80/100
125
160/200
250
320
M6
M8
M10
M10x1.25
M12
M12x1.25
M16
M16x1.5
M20x1.5
M27x2
M36x2
M42x2
M48x2
9 254 SGS-M6
9 255 SGS-M8
9 256 SGS-M10
9 261 SGS-M10x1.25
9 257 SGS-M12
9 262 SGS-M12x1.25
9 258 SGS-M16
9 263 SGS-M16x1.5
9 264 SGS-M20x1.5
10 774 SGS-M27x2
10 775 SGS-M36x2
10 776 SGS-M42x2
10 777 SGS-M48x2
M37 23 0251
M37 23 0252
M37 23 0253
M37 23 0307
M37 23 0254
M37 23 0198
M37 23 0257
M37 23 0258
M37 23 0260
M37 23 0308
M37 23 0309
M37 23 0310
M37 23 0311
Order example: Rod eye for piston∅ 50 mm: 9 263 M37 23 0258
Opel designation for rod eye for piston∅ 50 mm:
Rod eye M16x1.5 M37 23 0258
Hex nut
DIN 439
∅
[mm]
AV B1 CE CN
∅
H7
D1
∅
EF EN EU KK z ß1 ß2
– 12 3.2 30 6 13 10 9 6.8 M6 13 10 11
– 16 4 36 8 16 12 12 9 M8 13 13 14
25/32 20 5 43 10 19 14 14 10.5 M10 13 16 17
M10x1.25 17
40 22 6 50 12 22 16 16 12 M12 13 18 19
M12x1.25 19
50/63 28 8 64 16 27 21 21 15 M16 15 24 22
M16x1.5
80/100 33 10 77 20 34 25 25 18 M20x1.5 15 30 30
125 51 13.5 110 30 50 35 37 25 M27x2 15 41 41
160/200 56 18 125 35 58 40 43 28 M36x2 15 55 50
250 65 21 142 40 65 45 49 33 M42x2 15 65 55
320 75 24 160 50 75 57.5 60 45 M48x2 15 75 65
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 21
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 320 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Scope of delivery:
1 rod clevis with hex nut per
DIN 439 and
1 pin with lock
Supplied assembled
For swivelling cylinder mounting
with pivot pin
The rod clevis is fitted to the front pis-
ton rod end and permits a swivelling
movement of the cylinder in one
plane.
Rod clevisFesto type SG
∅
[mm]
Piston rod
thread
Festo order code
Part No. Type
Opel material no. DIN
ISO
8140
DIN
7152
32
40
50/63
80/100
125
160/200
250
320
M10x1.25
M12x1.25
M16x1.5
M20x1.5
M27x2
M36x2
M42x2
M48x2
6 144 SG-M10x1.25
6 145 SG-M12x1.25
6 146 SG-M16x1.5
6 147 SG-M20x1.5
14 987 SG-M27x2-B
9 581 SG-M36x2
9 582 SG-M42x2
9 583 SG-M48x2
M13 91 1062
M13 91 0452
M13 91 1059
M13 91 1034
M13 91 1096
M13 91 1057
M13 91 1097
M13 91 1098
X
X
X
X
X
X
X
X
X
X
X
–
–
–
–
–
Order example: Rod clevis for piston∅ 50 mm: 6 146 M13 91 1059
Opel designation for rod clevis for piston∅ 50 mm:
Rod clevis M16x1.5 M13 91 1059
Hex nut
DIN 439
∅
[mm]
B1 B2 B3 CE
±0.4
CK
∅
H9
CM CV D1
∅
KK LE
±0.5
ß1
32 5 26 20 40 10 10 12 18 M10x1.25 20 17
40 6 31 24 48 12 12 14 20 M12x1.25 24 19
50/63 8 39 32 64 16 16 19 26 M16x1.5 32 24
80/100 10 54 40 80 20 20 25 34 M20x1.5 40 30
125 13.5 74 55 110 30 30 38 48 M27x2 54 41
160/200 18 92 70 144 35 35 44 60 M36x2 72 55
250 21 111 85 168 40 40 64 70 M42x2 84 65
320 24 123 90 192 50 50 73 80 M48x2 96 75
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0522
Cylinder accessories to Opel standard, material no. M13 91...Piston∅ 32 ... 200 mm, per ISO 6431, VDMA 24 562 and NF E 49 003.1
Self-aligning rod couplerFesto type FK
With hex nut per
DIN 439.
The coupling links the piston rod end
of all cylinder types to the machine
parts to be moved. It compensates for
radial and angular deviations
(misalignment).
Scope of delivery:
1 Self-aligning rod coupler with hex
nut
∅
[mm] Piston rod thread
Festo order code
Part No. Type
Opel material no.
32
40
50/63
80/100
125
160/200
M6
M8
M10
M10x1.25
M12x1.25
M16
M16x1.5
M20
M20x1.5
M27x2
M36x2
2 061 FK-M6
2 062 FK-M8
2 063 FK-M10
6 140 FK-M10x1.25
6 141 FK-M12x1.25
2 065 FK-M16
6 142 FK-M16x1.5
2 066 FK-M20
6 143 FK-M20x1.5
10 485 FK-M27x2
10 746 FK-M36x2
M13 91 0394
M13 91 0075
M13 91 0274
M13 91 1095
M13 91 1040
M13 91 0076
M13 91 0808
M13 91 0077
M13 91 0275
M13 91 1099
M13 91 1100
Order example: Self-aligning rod coupler for piston∅ 50 mm: 6 142 M13 91 0808
Opel designation for self-aligning rod coupler for piston∅ 50 mm:
Self-aligning rod coupler M16x1.5 M13 91 0808
Angular compensation
Axial compensation of central axis
∅
[mm]
B1 D1
∅
D2
∅
D3
∅
L1 L2 L3 L4 L5 L6 KK ß1 ß2 ß3 ß4
– 3.2 8.5 14.5 5.8 37 25 4.4 17.5 11.5 15.7 M6 7 13 5 10
– 4 12.5 19 7.8 49 34 6 23.5 14 20.5 M8 10 17 7 13
32 5 21.8 32 13.8 67.5 49.5 9 34 23 31 M10 19 30 12 17
69.5 M10x1.25
40 6 21.8 32 13.8 74.5 50.5 10 34 24 32 M12x1.25 19 30 12 19
50/63 8 33.8 45 22 97 71 10 53 32 44.5 M16 30 41 19 24
103 M16x1.5
80/100 10 33.8 45 25 120 80 19 53 41 53.5 M20 30 41 19 30
M20x1.5
125 13.5 – 62 28 157 103 12.2 79 42 62.6 M27x2 55 55 24 41
160/200 18 – 80 36 251 179 22 136 78 110 M36x2 75 75 32 55
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 23
ISO valves to Opel standardContents
Standard valves
Designation Festo type Opel material no. Page
Solenoid valves with
port pattern per ISO 5599/1
ISO size 1, 3 and 4
MDH-5/2-...
JMDH-5/2-...
MDH-5/3...
M32 ... 24
Solenoid valves with
port pattern per ISO 15407-1
Size 01 and 02
VSVA-... M32 ... 28
Valve accessoriesDesignation Festo type Opel material no. Page
Plug sockets
per DIN EN 175301-803
MSSD-...
KMEB-..
MEB-...
M32 91 ... 32
Sub-bases with
port pattern per ISO 5599/1
External dimensions per
VDMA 24 345
ISO size 1, 3 and 4
NAS-...
NAV-...
NEV-...
NDV-...
NSC-...
NZV-...
M32 91 ... 34
Sub-bases with
port pattern per ISO 15407-1
Size 01 and 02
NAS-...
NAW-...
NEV-...
NZV-...
NDV-...
35
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0524
ISO valves to Opel standard, material no. M32 ...Solenoid valves, size 1 (G¼), size 3 (G½) and size 4 (G¾) with port pattern per ISO 5599/1
Solenoid valveFesto type MDH
Double solenoid valveFesto type JMDH
-M- Flow rate
Size 1 – 1200 l/min
Size 3 – 4100 ... 4600 l/min
Size 4 – 6000 l/min
-P- Voltage
24 V DC
230 V AC
24 V DC/42 V AC
-L- Operating pressure
2 ... 16 bar
-Q- Temperature range
Ambient temperature
–10 ... +50 °C
Medium temperature
–10 ... +60 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– Maintenance-free
– Non-overlapping
– PWIS1) -free
– Captive mounting screws
– With manual override, push to
reset
– Protection (with plug socket) IP 65
– Duty cycle 100%
– 3 voltages:
24 V DC,
6.8 W nominal power
230 V AC/50 Hz,
10.5 VA holding power
24 V DC/42 V AC/50 Hz,
12.2 VA holding power
Accessories:
Plug sockets to Opel standard and
DIN EN 175301-803, with green
actuation indicator and transparent
housing:
Type A with grey PG threaded
connector (for port 14).
Type B with black PG threaded
connector (for port 12).
Plug sockets must be ordered
separately, see page 32.
See page 34 for valve sub-bases.
1) PWIS = paint-wetting impairment substances
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 25
ISO valves to Opel standard, material no. M32 ...Solenoid valves, size 1 (G¼), size 3 (G½) and size 4 (G¾) with port pattern per ISO 5599/1
Technical data
Symbol ISO size
ISO code
Opel
material no.
Voltage Nominal
bore
[mm]
Nominal
flow rate
1 > 2, 1 > 4
[l/min]
Operating
pressure
[bar]
Response
time
at 6 bar
On/Off
[ms]
Festo order code
Part No. Type
1 52 M32 15 0296 24 V DC/42 V AC 8 1200 3 ... 16 18/40 43 281 MDH-5/2-D-1-FR-C
M32 15 0297 230 V AC 43 282 MDH-5/2-D-1-FR-C
3 52 M32 15 0298 24 V DC/42 V AC 14.5 4500 3 ... 16 28/68 43 289 MDH-5/2-D-3-FR-C
M32 15 0299 230 V AC 43 290 MDH-5/2-D-3-FR-C
4 52 M32 15 0300 24 V DC/42 V AC 18 6000 3 ... 16 53/85 35 636 MDH-5/2-D-4-24-FR
M32 15 0301 230 V AC 35 636 MDH-5/2-D-4-230-FR
1 55 M32 15 0302 24 V DC/42 V AC 8 1200 2 ... 16 16/16 43 283 JMDH-5/2-D-1-C
M32 15 0303 230 V AC 43 284 JMDH-5/2-D-1-C
3 55 M32 15 0304 24 V DC/42 V AC 14.5 4500 2 ... 16 21/21 43 291 JMDH-5/2-D-3-C
M32 15 0305 230 V AC 43 292 JMDH-5/2-D-3-C
4 55 M32 15 0306 24 V DC/42 V AC 18 6000 2 ... 16 40/40 35 942 JMDH-5/2-D-4-24
M32 15 0307 230 V AC 35 942 JMDH-5/2-D-4-230
1 56 M32 18 0078 24 V DC/42 V AC 8 1200 3 ... 16 18/41 43 285 MDH-5/3G-D-1-C
M32 18 0079 230 V AC 43 286 MDH-5/3G-D-1-C
3 56 M32 18 0082 24 V DC/42 V AC 14.5 4100 3 ... 16 35/79 43 293 MDH-5/3G-D-3-C
M32 18 0083 230 V AC 43 294 MDH-5/3G-D-3-C
1 57 M32 18 0080 24 V DC/42 V AC 8 1200 3 ... 16 18/43 43 287 MDH-5/3E-D-1-C
M32 18 0081 230 V AC 43 288 MDH-5/3E-D-1-C
3 57 M32 18 0084 24 V DC/42 V AC 14.5 4600 3 ... 16 36/84 43 295 MDH-5/3E-D-3-C
M32 18 0085 230 V AC 43 296 MDH-5/3E-D-3-C
Order example: 5/2-way solenoid valve, suitable for voltages of 24 V DC and 42 V AC:MDH-5/2-D-4-24-FR 35 636 M32 15 0300
Opel designation for 5/2-way single solenoid valve, ISO size 4, with 24/42 solenoid coil:
5/2-way valve 4 - 24/42 V - M32 15 0300
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0526
ISO valves to Opel standard, material no. M32 ...Solenoid valves, size 1 (G¼), size 3 (G½) and size 4 (G¾) with port pattern per ISO 5599/1
Solenoid valveMDH-5/2-...
5/2-way valveISO size 1 and 3
Double solenoid valveJMDH-5/2...
5/2-way valveISO size 1 and 3
Solenoid valveMDH-5/3...5/3-way valve
ISO size 1 and 3
1 Port pattern per
DIN EN 175301-803
2 Manual override
3 Captive screws
Type B1 B2 B3 B4 D1 H1 H2 H3 H4 H5 L1 L2 L3 L4 L5 L6
ISO size 1
MDH-5/2-D-1-FR-C
42 28 6 30 M5 103 74.2 38 9 46.5
98 43.8
36 18 91.5JMDH-5/2-D-1-C 156 87.6 43.8
MDH-5/3...-D-1-C 108.4 54.2
ISO size 3
MDH-5/2-D-3-FR-C
65 48 12 30 M8 120 91.2 55 12 63.5
164.7 72.7
64 32 111JMDH-5/2-D-3-C 194.4 145.4 72.7
MDH-5/3...-D-3-C 184 92
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 27
ISO valves to Opel standard, material no. M32 ...Solenoid valves, size 1 (G¼), size 3 (G½) and size 4 (G¾) with port pattern per ISO 5599/1
Solenoid valveMDH-5/2-...
5/2-way valveISO size 4
Double solenoid valveJMDH-5/2-...
5/2-way valvesISO size 4
1 Port pattern per
DIN EN 175301-803
2 Manual override
3 Captive screws
4 Solenoid can be rotated 90°
independent of manual override.
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0528
Standard valves to Opel standard, material no. M32 ...Solenoid valves, size 01 (G¼) and size 02 (Gx) with port pattern per ISO 15407-1
Solenoid valveFesto type VSVA
-M- Flow rate
Size 01
1000 ... 1100 l/min
Size 02
450 ... 550 l/min
-P- Voltage
24 V DC
230 V AC/50 Hz
-L- Operating pressure
2 ... 10 bar
-Q- Temperature range
Ambient temperature
–5 ... +50 °C
Medium temperature
–5 ... +50 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– Maintenance-free
– Non-overlapping
– PWIS1) -free
– Electrical interface per
DIN EN 175301-803
– Degree of protection (with plug
socket) IP 65
– Duty cycle 100%
– 2 voltages:
24 V DC,
1.8 W nominal power
230 V AC/50 Hz,
2.1 VA holding power
Flexible use
Easy mounting
– Captive mounting screws and seal
Quick mounting
– only 2 mounting screws
Exhaust air
– Ducted exhaust air
– Ducted pilot exhaust air
Simple servicing
– Tubings need not be disconnected
for valve replacement
Accessories:
Plug sockets to Opel standard and
DIN EN 175301-803.
Plug sockets must be ordered
separately, see page 32.
See page 34 for valve sub-bases.
1) PWIS = paint-wetting impairment substances
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 29
Standard valves to Opel standard, material no. M32 ...Solenoid valves, size 01 (G¼) and size 02 (Gx) with port pattern per ISO 15407-1
Technical data
Symbol ISO size
ISO code
Opel
material no.
Voltage Nominal
bore
[mm]
Nominal
flow rate
1 > 2, 1 > 4
[l/min]
Operating
pressure
[bar]
Response time
at 6 bar
On/Off
[ms]
Festo order code
Part No. Type
01 52 M32 15 0420 24 V DC 9 1100 3 ... 10 26/56 546 702 VSVA-B-M52-MH-A1-1C1
M32 15 0421 230 V AC 547 220 VSVA-B-M52-MH-A1-3AC1
02 52 M32 15 0424 24 V DC 5 550 3 ... 10 17/35 546 703 VSVA-B-M52-MH-A2-1C1
M32 15 0425 230 V AC 547 221 VSVA-B-M52-MH-A2-3AC1
01 55 M32 15 0422 24 V DC 9 1100 2 ... 10 18/18 546 696 VSVA-B-B52-H-A1-1C1
M32 15 0423 230 V AC 547 214 VSVA-B-B52-H-A1-3AC1
02 55 M32 15 0426 24 V DC 5 550 2 ... 10 15/15 546 697 VSVA-B-B52-H-A2-1C1
M32 15 0427 230 V AC 547 215 VSVA-B-B52-H-A2-3AC1
01 56 M32 18 0114 24 V DC 9 1000 3 ... 10 23/58 546 708 VSVA-B-P53C-H-A1-1C1
M32 18 0115 230 V AC 547 226 VSVA-B-P53C-H-A1-3AC1
02 56 M32 18 0118 24 V DC 5 450 3 ... 10 18/30 546 709 VSVA-B-P53C-H-A2-1C1
M32 18 0119 230 V AC 547 227 VSVA-B-P53C-H-A2-3AC1
01 57 M32 18 0116 24 V DC 9 1000 3 ... 10 23/58 546 706 VSVA-B-P53E-H-A1-1C1
M32 18 0117 230 V AC 547 224 VSVA-B-P53E-H-A1-3AC1
02 57 M32 18 0120 24 V DC 5 450 3 ... 10 18/30 546 707 VSVA-B-P53E-H-A2-1C1
M32 18 0121 230 V AC 547 225 VSVA-B-P53E-H-A2-3AC1
Order example: 5/2-way solenoid valve for a voltage of 24 V DC: VSVA-B-M52-MH-A1-1C1 546 702 M32 15 0420
Opel designation for 5/2-way single solenoid valve, ISO size 01, with 24 volt solenoid coil:
5/2-way valve 01 - 24 V - M32 15 0420
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0530
Standard valves to Opel standard, material no. M32 ...Solenoid valves, size 01 (G¼) and size 02 (Gx) with port pattern per ISO 15407-1
Solenoid valveVSVA-B-M52...
5/2-way valve, single solenoid
1 Wiring at plug socket per
DIN EN 175301-803, type C
2 Manual override
3 Captive screws
4 Slot for inscription label
Type B1 B2 D1 H1 H2 H3 H4 H5 L1 L2 L3 L4 L5
ISO size 01
VSVA-B-M52... 26.3 19 M4 89.2 71.2 62.6 39.3 7 113.1 63.1 29.75 61.6 123.2
ISO size 02
VSVA-B-M52... 18 12.5 M3 80.6 62.2 53.6 30.3 5.4 95.4 53.9 21.25 53.1 102.2
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 31
Standard valves to Opel standard, material no. M32 ...Solenoid valves, size 01 (G¼) and size 02 (Gx) with port pattern per ISO 15407-1
Solenoid valveVSVA-B-M52...
5/2-way valve, bistable,5/3-way valve
1 Wiring at plug socket per
DIN EN 175301-803, type C
2 Manual override
3 Captive screws
4 Slot for inscription label
Type B1 B2 D1 H1 H2 H3 H4 H5 L1 L2 L3 L4 L5
ISO size 01
VSVA-B-M52... 26.3 19 M4 89.2 71.2 62.2 39.3 7 126.2 63.1 29.75 61.6 123.2
ISO size 02
VSVA-B-M52... 18 12.5 M3 80.6 62.2 53.6 30.3 5.4 107.8 53.9 21.25 53.1 102.2
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0532
Valve accessories to Opel standard, material no. M32 91 ...Plug sockets per DIN EN 175301-803
KMEB MEBMSSD-EB MSSD-C
SocketFesto type MSSD
Plug socket with cableFesto type KMEBIlluminating seal
Festo type MEB
– Plug sockets MSSDConnection diagram:
DIN EN 175301-803
– With transparent housing, formed
gasket and green LED
– Degree of protection: IP 65
– Plug sockets with cable KMEBConnection diagram:
DIN EN 175301-803
– Cable lengths: 2.5 and 5 m
– Degree of protection: IP 65
– Illuminating seal MEBWith yellow LED
– Degree of protection: IP 65
– Protective circuit
For detailed product informationsee DVD andwww.festo.com/catalogue/<type>
Plug socket per
DIN EN 175301-803 for
valves per ISO 5599/1
Voltage Cable
length
Cable conduit fitting/colour Opel material no. Type Festo order code
Part No. Type
Type A with green LED
transparent housing
24 V DC – Pg11/grey M32 91 2648 A** 35 945 MSSD-C14-TG-24=Opel
Pg11/black M32 91 2649 B*** 35 944 MSSD-C12-TS-24=Opel
Type A with green LED
transparent housing
230 V AC – Pg11/grey M32 91 2242 A** 35 949 MSSD-C14-TG-230~Opel*
Pg11/black M32 91 2243 B*** 35 948 MSSD-C12-TS-230~Opel*
Type A without LED – – Pg9/black M32 91 0349 B*** 34 583 MSSD-C
Plug socket per
DIN EN 175301-803 for
valves per VDMA 24 563
Type C flat seal – – Pg7 – – 151 687 MSSD-EB
Type C with yellow LED
Protective circuit
24 V DC 2.5 m – – – 151 688 KMEB-1-24-2.5-LED
5 m – – 151 689 KMEB-1-24-5-LED
Type C
without LED
230 V AC 2.5 m – – – 151 690 KMEB-1-230-2.5
5 m – – 151 691 KMEB-1-230-5
Illuminating seal 24 V DC – – – – 151 717 MEB-LD-12-24
230 V AC – – 151 718 MEB-LD-230
* upon request ** Type A for port 14 *** Type B for port 12
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 33
Valve accessories to Opel standard, material no. M32 91 ...Plug sockets per DIN EN 175301-803
12 ... 24 V 230 V Circuit diagrams
1 Inserts can be rotated 90°
SocketMSSD-C14-TG-...
MSSD-C12-TS-...
1 Inserts can be rotated 90°
SocketMSSD-C14-C
MSSD-C
1 Inserts can be rotated 90°
SocketMSSD-EB
3 LED illuminated field
5 Circuit diagram
8 Designation clip
aB Port pattern per
DIN EN 175301-803
aC Wires: 3 x 0.5 mm2
Plug socket with cableKMEB-...
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0534
Valve accessories to Opel standard, material no. M32 91 ...ISO sub-bases, size 1 (G¼), size 3 (G½) and size 4 (G¾) with port pattern per ISO 5599/1 and external dimensions per VDMA 24 345
Sub-basesISO 5599/1
Designation Size Opel material no. Part No. Type
Individual sub-base
Connections at side
Type A
1 M32 91 2221 9 484 NAS-¼-1A-ISO
3 M32 91 2224 10 336 NAS-½-3A-ISO
4 M32 91 2227 152 813 NAS-¾-4A-ISO
Series sub-base
(manifold sub-base)
Type C
1 M32 91 2222 10 173 NAV-¼-1C-ISO
3 M32 91 2225 10 175 NAV-½-3C-ISO
4 M32 91 2228 11 139 NAV-¾-4C-ISO
End plate kit
(left and right end plates)
Type D
1 M32 91 2223 10 174 NEV-1DA/DB-ISO
3 M32 91 2226 10 176 NEV-3DA/DB-ISO
4 M32 91 2229 11 140 NEV-4DA/DB-ISO
Blanking plate 1 M32 91 2230 9 489 NDV-1-ISO
3 M32 91 2231 10 340 NDV-3-ISO
4 M32 91 2232 11 142 NDV-4-ISO
Isolating disc 1 M32 91 2233 11 550 NSC-¼-1-ISO
3 M32 91 2234 11 551 NSC-½-3-ISO
4 M32 91 2235 11 699 NSC-¾-4-ISO
Intermediate plate for linking
ISO size 1 to ISO size 3
1 M32 91 2244 12 911 NZV-3-2/1
3 M32 91 2244
– –
Order example: End plate kit, type D, size 1: 10 174 M32 91 2223
Type A: individual sub-base,
connecting thread on the
side
Type C: manifold sub-base,
connecting thread for
working line underneath,
pilot port on the side
Type D: end plate for manifold
sub-base, Type C
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 35
Valve accessories to Opel standardVDMA sub-bases, size 01 (G¼) and size 02 (Gx) with port pattern per ISO 15407-1
Sub-basesISO 15407-1
Designation Size Opel material no. Part No. Type
Individual sub-base
Connections at side
01 – 161 109 NAS-¼-01-VDMA
02 – 161 115 NAS-x-02-VDMA
Manifold sub-base
for pneumatic valves
4
2
12
01 – 161 103 NAW-¼-01-VDMA-VL
02 – 161 111 NAW-x-02-VDMA-VL
Manifold sub-base
for solenoid valves
4
2
12
01 – 161 102 NAW-¼-01-VDMA
02 – 161 110 NAW-x-02-VDMA
End plate 01 – 161 104 NEV-01-VDMA
02 – 161 112 NEV-02-VDMA
Intermediate plate 01/02 – 161 108 NZV-01/02-VDMA
Blanking plate 01 – 161 107 NDV-01-VDMA
02 – 161 114 NDV-02-VDMA
Order example: End plate, size 01: 161 104 NEV-01-VDMA
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0536
Other products to Opel standardContents
Designation Opel material no. Festo type Page
Valves One-way flow control valve M32 06 ... GRLA-...-B 37
Quick exhaust valve M32 08 0026 SE-¼-B 38
Exhaust air restrictor M32 11 ... GRU-½-B
GRE-...
39
Ball valve M22 07 ... QH-... 40
Individual units Pressure gauge M15 04 ... MA-... 41
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 37
Non-return and flow control valves for drive units to Opel standard, material no. M32 06 ...One-way flow control valves, Gx ... G¾
One-way flow control valveFesto type GRLA
-M- Flow rate
0 ... 2000 l/min
-L- Operating pressure
0.3 ... 10 bar
-Q- Temperature range
–10 ... +60 °C
– Medium:
Filtered compressed air,
lubricated or unlubricated
One-way flow control valves withexhaust-air flow control
are used to regulate exhaust air flow
rates with double-acting cylinders. In
the reverse direction, the air flows
through the non-return valve with full
cross-sectional flow.
– Threaded connection Gx to G¾
– Can be mounted directly on
cylinder
– Rotatable 360°
Festo order code
Part No. Type
Opel material no.
151 165 GRLA-x-B M32 06 0081
151 172 GRLA-¼-B M32 06 0095
151 178 GRLA-y-B M32 06 0096
151 179 GRLA-½-B M32 06 0150
151 180 GRLA-¾-B M32 06 0154
Order example: One-way flow control valve with threaded connection G¼: 151 172 M32 06 0095
Opel designation for one-way flow control valve with connecting thread G¼:
One-way flow control valve G¼ M32 06 0095
For detailed product informationsee DVD and
www.festo.com/catalogue/grla
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0538
Non-return and flow control valves for drive units to Opel standard, material no. M32 08 ...Quick exhaust valves G¼
Quick exhaust valvewithout silencer
Festo type SE-¼-B
-M- Flow rate
300 ... 660 l/min
-L- Operating pressure
0.5 ... 10 bar
-Q- Temperature range
–20 ... +75 °C
– Medium:
Filtered compressed air,
lubricated or unlubricated
– Ducted exhaust air
These components allow higher pis-
ton speeds to be achieved on the re-
turn stroke of single and double-
acting cylinders.
Compressed air flows from the pilot
valve, and via the quick exhaust valve
to the cylinder. Exhaust port 3 is
closed at this time. When the pres-
sure at 1 falls, exhaust flow occurs
from 2 to 3.
In order to achieve the full benefit of
the quick exhaust function, the valve
must be connected directly to the
exhaust port of the cylinder.
Exhaust noise is reduced by silencers.
Threaded connection Festo order code
Part No. Type
Opel material no.
G¼ 9 686 SE-¼-B M32 08 0026
For detailed product informationsee DVD and
www.festo.com/catalogue/se
Order example: Quick exhaust valve with threaded connection G¼: 9 686 M32 08 0026
Opel designation for quick exhaust valve with connecting thread G¼:
Quick exhaust valve G¼ M32 08 0026
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 39
Non-return, flow control and pressure control valves to Opel standard, material no. M32 11 ...Flow control valve Gx ... G½
GRE-... GRU-...-B
Exhaust air restrictorFesto type GRU-.../GRE
-M- Flow rate
520 ... 8000 l/min
-L- Max. operating pressure
0 ... 10 bar
-Q- Temperature range
–10 ... +70 °C
– Medium:
Filtered compressed air,
lubricated or unlubricated
These valves are screwed into control
valve exhaust ports 3 and 5, and
make it possible to control piston
speeds of cylinders by means of
exhaust port flow control.
Exhaust air restriction can be ad-
justed with the throttle screw. Exhaust
air is discharged via the integrated
silencer for reduced noise levels.
Festo order code
Part No. Type
Opel material no.
9 519 GRU-½-B M32 11 0248
10 351 GRE-x M32 11 0259
10 352 GRE-¼ M32 11 026010 353 GRE-½ M32 11 0261
Order example: Exhaust air restrictor with threaded connection G¼: 10 352 M32 11 0260 For detailed product informationsee DVD and
www.festo.com/catalogue/greOpel designation for exhaust air restrictor with connecting thread G¼:
Flow control valve G¼ M32 11 0260
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0540
Non-return, flow control and pressure control valves to Opel standard, material no. M22 07 ...Shut-off valves Gy ... G1½
Ball valveFesto type QH
-M- Flow rate
to 84,000 l/min
-L- Operating pressure
–0.95 ... +30 bar
-Q- Temperature range
–30 ... +200 °C
-R- Vacuum
suitable for vacuum
– Medium:
Filtered compressed air,
lubricated or unlubricated
Air flow is fully blocked in both
directions with this valve by turning
the lever.
-H- NoteThis version is not suitable for poi-
sonous gas, e.g. natural gas etc.
Festo order code
Part No. Type
Opel material no.
9 542 QH-y M22 07 0003
9 544 QH-¾ M22 07 0007
9 545 QH-1 M22 07 00086 837 QH-1½ M22 07 0011
For detailed product informationsee DVD and
www.festo.com/catalogue/qh
Order example: Ball valve with threaded connection Gy: 9 542 M22 07 0003
Opel designation for ball valve with connecting thread Gy:
Stop cock QH-Gy without exhaust M22 07 0003
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 41
Individual units for compressed air preparation to Opel standard, material no. M15 04 ...Indicators, G¼
Pressure gaugeFesto type MA
Type E, connector trunnion centred at
back, without mounting rim
-Q- Temperature range
–10 ... +60 °C
For general use per DIN EN 837-1
– Medium:
Filtered compressed air,
lubricated or unlubricated
– Display range: 0 ... 16 bar
– G¼ connections
These pressure gauges are used to
measure and display pressure at
control systems.
They are free of paint-wetting impair-
ment substances.
Pressure gauges may only be loaded
to¾ of their full scale value during
continuous operation.
Indicating range
[bar]
Festo order code
Part No. Type
Opel material no.
0 ... 2.5 162 845 MA-63-2.5-¼-EN M15 04 0306
0 ... 10 162 840 MA-63-10-¼-EN M15 04 0057
0 ... 16 162 841 MA-63-16-¼-EN M15 04 0079
Order example: Pressure gauge, display range from 0 to 16 bar: 162 841 M15 04 0079 For detailed product informationsee DVD and
www.festo.com/catalogue/maOpel designation for type E pressure gauge with display range from 0 to 16 bar:
Pressure gauge 1.6E 0 – 16 M15 04 0079
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0542
Cylinders to Opel standardTable of contents
Designation Festo type Page
Multi-position cylinderMulti-position cylinderOperating cylinder for
Euro-C welding guns
Piston∅ 70 and 90 mm
D-...-PV2-C-SA 43
Multi-position cylinderOperating cylinder for
Euro-X welding guns
Piston∅ 80 ... 125 mm
DNG-...-30-100-P-SA 45
Multi-position cylinderOperating cylinder for
Euro-X welding guns
Piston∅ 100 ... 125 mm
D-...-60-30-PV2-SA 47
Double-acting cylinder
Double-acting cylinderFor use as drawn part lifter
in press tools
Piston∅ 35 mm
D-35-...-PP-SA 49
Double-acting cylinderCompensating cylinder for
Euro-X welding guns
Piston∅ 50 and 63 mm
D-...-20-P-SA 51
Double-acting cylinderCompensating cylinder for
Euro-C welding guns
Piston∅ 32 and 40 mm
D-...-35-P-SA 53
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 43
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 70 and 90 mm
Multi-position cylinderOperating cylinder for Euro-C welding
gun
Festo type D-...-PV2-C-SA
-N- Diameter
70 and 90 mm
-T- Stroke length
Forward stroke
30 ... 120 mm
Working stroke
46 mm
-L- Operating pressure
max. 12 bar
-Q- Temperature range
–20 ... +80 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– Three-position cylinder with for-
ward stroke and working stroke
– For use in welding guns
– Reinforced piston rod
– Reinforced support
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0544
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 70 and 90 mm
Multi-position cylinderD-...-PV2-C-SA
∅
[mm]
Forward
stroke
[mm]
Working
stroke
[mm]
Festo order code
Part No. Type
Opel material no.
70 30 46 197639 D-70-30-46-PV2-C-SA M13 01 9760
50 197638 D-70-50-46-PV2-C-SA M13 01 6128
80 197637 D-70-80-46-PV2-C-SA M13 01 5274
100 197636 D-70-100-46-PV2-C-SA M13 01 6129
120 197635 D-70-120-46-PV2-C-SA M13 01 5272
90 30 46 197645 D-90-30-46-PV2-C-SA M13 01 9763
50 197644 D-90-50-46-PV2-C-SA M13 01 6130
80 197643 D-90-80-46-PV2-C-SA M13 01 5277
100 197642 D-90-100-46-PV2-C-SA M13 01 6131
120 197641 D-90-120-46-PV2-C-SA M13 01 5276
Order example: Multi-position cylinder, piston∅ 70 mm, forward stroke 100 mm, working stroke 46 mm:
197636 D-70-100-46-PV2-C-SA
D-70-... (values in brackets)
D-90-...
1 Working stroke advance
2 Forward stroke advance
3 Return stroke
4 Regulating screw for end-posi-
tion cushioning
+ VH = plus forward stoke
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 45
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 80 ... 125 mm
Multi-position cylinderOperating cylinder for
Euro-X welding guns
Festo type DNG-...-30-100-P-SA
VR: Forward stroke return
VV: Forward stroke advance
AV: Working stroke advance
AR: Working stroke return
-N- Diameter
80 ... 125 mm
-T- Stroke length
Working stroke
30 mm
Forward stroke
100 mm
-L- Operating pressure
max. 12 bar
-Q- Temperature range
–20 ... +80 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– For use in welding guns
– Reinforced piston rods
Accessories:
Stroke limiting discs are available as
accessories.
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0546
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 80 ... 125 mm
Multi-position cylinderDNG-...-30-100-P-SA
∅
[mm]
Forward
stroke
[mm]
Working
stroke
[mm]
Festo order code
Part No. Type
Opel material no.
80 100 30 155776 DNG-80-30/100-P-SA M13 01 6132
100 100 30 173185 DNG-100-30/100-P-SA M13 01 6133
125 100 30 155678 DNG-125-30-100-P-SA –
Order example: Multi-position cylinder, piston∅ 125 mm, forward stroke 100 mm, working stroke 30 mm:
155678 DNG-125-30-100-P-SA
1 Connection for working stroke advance
2 Connection for working stroke return
3 Connection for forward stroke advance
4 Connection for forward stroke return
∅
[mm]
AF B
∅
E E1 EE J1 KF
80 32 55 100 100 G¼ 30 M20x1.5
100 32 55 126 124 G¼ 30 M20x1.5
125 32 55 140 140 G¼ 40 M20x1.5
∅
[mm]
L2 MM
h8
PL PL1 TG VD WH ZJ ZM+ ß 1 ß 2
80 90 32 10 10 72 20 33 263 296 27 7
100 89 32 9 9 89 20 33 263 296 27 7
125 128 32 17 12 110 8 22 324 346 27 9
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 47
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 100 ... 125 mm
Multi-position cylinderOperating cylinder for
Euro-X welding guns
Festo type D-...-60-30-PV2-SA
-N- Diameter
100 ... 125 mm
-T- Stroke length
Forward stroke
60 mm
Working stroke
30 mm
-L- Operating pressure
max. 12 bar
-Q- Temperature range
–20 ... +80 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– Three-position cylinder with for-
ward stroke and working stroke
– For use in welding guns
– Reinforced piston rod
– Adjustable end-position cushion-
ing in the working stroke
Accessories:
Stroke limiting discs are available as
accessories.
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0548
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 100 ... 125 mm
Multi-position cylinderD-...-60-30-PV2-SA
∅
[mm]
Forward
stroke
[mm]
Working
stroke
[mm]
Festo order code
Part No. Type
Opel material no.
100 60 30 192867 D-100-60-30-PV2-SA M13 01 9820
125 60 30 194495 D-125-60-30-PV2-SA M13 01 9827
Order example: Multi-position cylinder, piston∅ 125 mm, forward stroke 60 mm, working stroke 30 mm:
194495 D-125-60-30-PV2-SA
1 Adjustable end-position cush-
ioning
RH = Return stroke
AH = Working stroke
VH = Forward stroke
∅
[mm]
BG D4
∅
D5
∅
E J1 J2 J3 J4 MM
∅
h8
PL ß1
100 50 107 10 120 30 18 21 30 32 25 27
125 42 133 12 133 37 28 25 40 40 23 36
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 49
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 35 mm
Double-acting cylinderFor use as drawn part lifter
in press tools
Festo type D-35-...-PP-SA
-N- Diameter
35 mm
-T- Stroke lengths
60, 75 and 90 mm
-L- Operating pressure
0.5 ... 10 bar
-Q- Temperature range
–20 ... +80 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– End-position cushioning at both
ends via fixed restrictor
– Cylinder barrel with hard-nickel
plating
– Air connections in the piston rod
Stroke
[mm]
∅
[mm]
Festo order code
Part No. Type
Opel material no.
60 35 38 550 D-35-60-PP-SA M13 01 3578
75 35 194 038 D-35-75-PP-SA M13 01 8794
90 35 38 551 D-35-90-PP-SA M13 01 3579
Order example: Double-acting cylinder, piston∅ 35 mm, 60 mm stroke: 38 550 D-35-60-PP-SA
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0550
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 35 mm
Double-acting cylinderD-35-...-PP-SA
1 Advance
2 Return
3 Rotatable 360°
+ = plus stroke length
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 51
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 50 mm and 63 mm
Double-acting cylinderCompensating cylinder for
Euro-X welding guns
Festo type D-…-20-P-SA
-N- Diameter
50 mm and 63 mm
-T- Stroke length
20 mm
-L- Operating pressure
0.5 ... 12 bar
-Q- Temperature range
–20 ... +80 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– For use in welding guns
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0552
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 50 mm and 63 mm
Double-acting cylinderD-...-20-P-SA
∅
[mm]
Stroke
[mm]
Festo order code
Part No. Type
Opel material no.
50 20 184809 D-50-20-P-SA M13 01 5644
63 20 526604 D-63-20-P-SA M13 01 5645
Order example: Double-acting cylinder, piston∅ 50 mm, stroke 20 mm
184809 D-50-20-P-SA
∅
[mm]
B1 B2 D1
∅
D2 D3
H7
∅
D4 EE H1 H2
∅
h8
H3
+0.1
H4 L1 L2
50 67.6 ~32.4 20 M10 10 M4 G1/4 67.6 58 15 2.9 80.5 50.5
63 86.6 ~36.1 86.6 3.9 82.5 52.5
∅
[mm]
L3
+0.1
L4
+0.3
L5 L6 L7 L8 L9 T1 T2 W1 ß1
50 68.5 10 42 18 13.5 8 6 15 8 60° 17
63 70.5 10 44
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 53
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 32 mm and 40 mm
Double-acting cylinderCompensating cylinder for
Euro-C welding guns
Festo type D-…-35-P-SA
-N- Diameter
32 mm and 40 mm
-T- Stroke length
35 mm
-L- Operating pressure
max.
12 bar
-Q- Temperature range
–20 ... +80 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– For use in welding guns
– With press-fit insulating bush on
connection side
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0554
Cylinders to Opel standard, material no. M13 01 ...Double-acting cylinder, piston∅ 32 mm and 40 mm
Double-acting cylinderD-...-35-P-SA
∅
[mm]
Stroke
[mm]
Festo order code
Part No. Type
Opel material no.
32 35 183529 D-32-35-P-SA M13 01 5646
40 35 549219 D-40-35-P-SA M13 01 5647
Order example: Double-acting cylinder, piston∅ 32 mm, stroke 35 mm
183529 D-32-35-P-SA
1 Insulating bush POM
∅
[mm]
B1 B2 B3 B4 D1
∅
D2
∅
D3 D4
∅
D5
∅
EE H1 H2
32 70 52 42 18 28 12 M8 8.2 11.5 G1/8 45 34.6
40 30 8.3
∅
[mm]
H3 H4 L1 L2 L3 L4 L5 L6 L7 T1 ß1 ß2
32 22.5 8 75 57 32 10 14 8 17 10 24 10
40 59 —
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 55
Control units to Opel standardTable of contents
Designation Festo type Page
Regulator plateRegulator plate, 2-way, for
compensating cylinder
RP VSPA 56
Regulator plate, 4-way, for
compensating cylinder
RP VSPA-VSVA 58
Valve manifoldValve manifold
for Euro C-45/C45HD welding
gun
Control block to ISO 15407 60
Valve manifold
for Euro X50/450 welding gun
and
X-1000 welding gun
Control block to ISO 5599 62
Valve manifold
for Euro X50/550 welding gun
Control block to ISO 5599 64
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0556
Regulator plates to Opel standardRegulator plate, 2-way, for compensating cylinder
Regulator plate, 2-way, forcompensating cylinder
Festo type Regulator plate RP VSPA
-L- Supply pressure (P1)
max. 12 bar
Setting ranges
1 ... 12 bar
Port 14
2 ... 12 bar
-Q- Temperature range
–10 ... +60 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– For compensating cylinder
– 2-way
– For stationary use
The regulator plate is a fully as-
sembled, ready-to-connect unit con-
sisting of:
– 1 pneumatic valve
– 2 regulators
– 2 pressure gauges with indication
of setpoint value
– 1 silencer
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 57
Regulator plates to Opel standardRegulator plate, 2-way, for compensating cylinder
Regulator plateRP VSPA
Festo order code
Part No. Type
Opel material no.
1389050 RP VSPA M32 03 1442
Order example: Regulator plate
1389050 RP VSPA
B1 H1 H2 L1 L2 L3
~84 ~95.1 10 87 66 10.5
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0558
Regulator plates to Opel standardRegulator plate, 4-way, for compensating cylinder
Regulator plate, 4-way, forcompensating cylinder
Festo type Regulator plateRP VSPA-VSVA
-L- Supply pressure (P2)
max. 12 bar
Setting ranges
1 ... 12 bar
Port 14
2 ... 12 bar
-Q- Temperature range
–10 ... +60 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
– For compensating cylinder
– 4-way
– For use on robots
The regulator plate is a fully as-
sembled, ready-to-connect unit con-
sisting of:
– 2 pneumatic valves
– 2 solenoid valves
– 4 regulators
– 4 pressure gauges with indication
of setpoint value
– 1 silencer
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 59
Regulator plates to Opel standardRegulator plate, 4-way, for compensating cylinder
Regulator plateRP VSPA-VSVA
Festo order code
Part No. Type
Opel material no.
1375452 RP VSPA-VSVA M32 03 1504
Order example: Regulator plate
1375452 RP VSPA-VSVA
B1 B2 B3 H1 L1 L2 L3
~159.1 78 5.7 ~117.8 ~141.6 110 5
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0560
Valve manifolds to Opel standardValve manifold for Euro C-45/C45HD welding gun
Valve manifoldfor Euro C-45/C45HD welding gun
Festo type Control block to ISO15407
-L- Supply pressure (E1)
max. 8 bar
-Q- Temperature range
5 ... 50 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
The valve manifold is a fully as-
sembled, ready-to-connect unit con-
sisting of:
– 1 valve manifold
– 3 solenoid valves
– 2 silencers
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 61
Valve manifolds to Opel standardValve manifold for Euro C-45/C45HD welding gun
Valve manifoldControl block to ISO 15407
Festo order code
Part No. Type
Opel material no.
1388296 Control block to ISO 15407 M32 09 1599
Order example: Control block
1388296 Control block to ISO 15407
B1 B2 B3 B4 H1 H2 L1 L2 L3 L4 L5
~128 71.5 44.5 17.5 ~98.8 26 ~122.5 69 48 27 6
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0562
Valve manifolds to Opel standardValve manifold for Euro X50/450 welding gun and X-1000 welding gun
Valve manifoldfor Euro X50/450 welding gun and
X-1000 welding gun
Festo type Control block to ISO 5599
-L- Supply pressure (E1)
max. 10 bar
-Q- Temperature range
5 ... 50 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
The valve manifold is a fully as-
sembled, ready-to-connect unit con-
sisting of:
– 1 valve manifold
– 3 solenoid valves
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 63
Valve manifolds to Opel standardValve manifold for Euro X50/450 welding gun and X-1000 welding gun
Valve manifoldControl block to ISO 5599
Festo order code
Part No. Type
Opel material no.
1388209 Control block to ISO 5599 M32 09 1293
Order example: Control block
1388209 Control block to ISO 5599
B1 H1 H2 L1 L2 L3 L4
~152 ~92.3 22 ~138.1 26.5 26.5 13.5
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0564
Valve manifolds to Opel standardValve manifold for Euro X50/550 welding gun
Valve manifoldfor Euro X50/550 welding gun
Festo type Control block to ISO 5599
-L- Supply pressure (E1)
max. 10 bar
-Q- Temperature range
5 ... 50 °C
– Medium:
Filtered compressed air, lubricated
or unlubricated
The valve manifold is a fully as-
sembled, ready-to-connect unit con-
sisting of:
– 1 valve manifold
– 2 solenoid valves
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 65
Valve manifolds to Opel standardValve manifold for Euro X50/550 welding gun
Valve manifoldControl block to ISO 5599
Festo order code
Part No. Type
Opel material no.
1388476 Control block to ISO 5599 M32 09 1294
Order example: Control block
1388476 Control block to ISO 5599
B1 H1 H2 L1 L2 L3 L4
~109 ~92.3 22 ~138.1 26.5 26.5 13.5
en
Festo AG & Co. KG – Automotive range – Subject to change – 2012/0566
Engineering tools
The course is already set at the system
design stage for efficient use of energy
and a rapid return on investment. You
can harness the surprisingly high level
of savings potential that exists in this
phase using the highly efficient selec-
tion and sizing software tools avail-
able. These tools are available for
both electrical and pneumatic drive
systems. Festo’s engineering tools
enable you to avoid oversizing compo-
nents and systems. At the same time,
the software tools optimally match all
the components and systems to your
application.
As a comprehensive supplier, Festo
supplies the ideal solution for every
application – regardless of the re-
quirements.
PositioningDrives Which electro-mechanical linear drive
best meets your needs? Enter the data
for your application such as position
values, effective loads and mounting
position and the software suggests a
number of optimum solutions.
Pneumatic sizing using ProPneu Perfect simulations replace expensive
actual tests. ProPneu is an expert sys-
tem that supports you in the selection
and configuration of the entire pneu-
matic control sequence. If one para-
meter is changed, the program auto-
matically adapts all the others.
Vacuum selection Which suction cup on which surface
for which movement? Don’t experi-
ment – calculate! This software tool
even enables linear and rotary move-
ments to be differentiated.
Tubing selection Simply enter parameters such as
working pressure, chemicals and re-
quired resistance to cleaning agents
and have the program calculate the
right tubing for your application.
Air consumption Calculate your system’s air consump-
tion quickly and conveniently. Simply
enter all the drives and tubing and set
the cycle times and working pressure
to calculate the air consumption per
minute and per day. Includes a fea-
ture for exporting the input table to-
gether with the result directly to Excel.
en
2012/05– Subject to change – Automotive range – Festo AG & Co. KG 67
Engineering tools
A secure grip is a question of the right
calculation. In this case, calculation
of weight, direction of movement, dis-
tances, etc. The software tool immedi-
ately determines which parallel,
radial, angle or 3-point grippers best
matches your requirements, and in
which size.
Gripper selection
Whether diagonal or vertical, curved
or straight, lever or disc, all types of
cushioned movements are taken into
account. The software tool is always
able to recommend the best shock ab-
sorber.
Shock-absorber selection
Juggling pencils and pocket calcula-
tors is now a thing of the past. No
matter whether you have discs,
blocks, push-on flanges, grippers,
etc.: this tool does the job of calculat-
ing all the mass moments of inertia.
Just save, send or print – and you’ve
finished.
Mass moment of inertia
Smart Soft Stop virtually makes the
impossible possible. Travel times are
reduced by as much as 30% for pneu-
matic drives, and greatly reduced
vibration is made possible. The selec-
tion program performs all the necess-
ary calculations.
Soft Stop
Festo’s linear drives are known for de-
livering maximum force from mini-
mum space. This software tool deter-
mines the optimum drive configura-
tion for you. You specify the project
parameters such as mass or force,
mounting position and travel.
Guide calculation for pneumaticlinear drives
en
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/05
Neumática para la industria
automovilística
Opel
Edición 05/2012
Todos los datos técnicos pueden
sufrir cambios en función de las
actualizaciones de los productos.
Todos los textos, gráficos, imágenes y
dibujos contenidos en esta publica-
ción son propiedad de
Festo AG & Co. KG y, en consecuencia,
están sujetos a los derechos de autor.
Queda prohibida su reproducción,
tratamiento, traducción, microfilma-
ción, memorización y procesamiento
mediante sistemas electrónicos sin
previa autorización explícita de
Festo AG & Co. KG.
Festo se reserva el derecho de efec-
tuar modificaciones como resultado
de la constante innovación de sus
productos.
Festo AG & Co. KG
Apartado de correos
73726 Esslingen
Ruiter Straße 82
73734 Esslingen
Alemania
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 1
Programa sector automóvilInformación general
Página
Cilindros ISO 2
Válvulas ISO 23
Otros productos 36
Ejecuciones especiales 55
Software de ingeniería 66
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/052
Cilindros ISO según norma de Opel∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
ÍndiceReferencia Tipo de Festo Norma de Opel
N° de referencia
Página
Cilindro con tirantes
para detección de posicio-
nes y con amortiguación
regulable
DOG-...-PPV-A M13 01... 4
Cilindro básico con brida
basculante central
DOGZK-... M13 01... 4
Accesorios para cilindros
Detectores
inductivo
SMTSO-...
SMBT-1
J06 13... 10
Pies de fijación HNG-... M13 91... 12
Brida de fijación FNG-... M13 91... 13
Caballete LNZG-... M13 91... 14
Brida basculante con
pivotes
SNGB-... M13 91... 15
Caballete LNG-...
LN-...
M13 91... 16
Caballete
con cojinete esférico
LSN-... M13 91... 17
Brida basculante con
pivotes
SNG-... M13 91... 18
Caballete con alojamiento
esférico
LSNG-... M13 91... 19
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 3
Cilindros ISO según norma de Opel∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
ÍndiceReferencia Tipo de Festo Norma de Opel
N° de referencia
Página
Cabeza de rótula SGS-... M37 23... 20
Horquilla SG-... M13 91... 21
Rótula FK-... M13 91... 22
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/054
Cilindros ISO según norma de Opel, n° de referencia M13 01...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
DOG-... DOGZK-...
Cilindro de doble efectoFesto tipo DOG
con brida basculante central,
Forma E
DOGZK
-N- Diámetro
32 ... 320 mm
-T- Carrera
25 ... 500 mm
-L- Presión de funcionamiento
máx.∅ del émbolo de
32 ... 125 mm
12 bar
160 ... 320 mm
10 bar
-Q- Temperatura
–20 ... +80 °C
– Fluido:
aire a presión filtrado,
con o sin lubricación
Cilindro básico sin fijaciones.
Los cilindros normalizados corres-
ponden a las normas
ISO 6431 (internacional)
DIN ISO 6431 y
VDMA 24 562 (Alemania)
NF E 49 003.1 (Francia)
UNI 10 290 (Italia)
DIN
NF E 49 003.1UNI 10 290
DOG-...-PPV-ACilindro con tirantes para detección
de posiciones y con amortiguación
regulable.
DOGZK-...-PPV-A
Cilindro con tirantes y brida bascu-
lante central, para detección de posi-
ciones y con amortiguación regulable.
La brida basculante central se monta
se serie en el centro del cilindro.
Es posible montar la brida de modo
descentrado. Indicar la medida XG
deseada (ver página 8).
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 5
Cilindros ISO según norma de Opel, n° de referencia M13 01...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Posibilidades de montaje
Montaje del cilindro básico
Montaje delante Montaje detrás
Accesorios
Variantes de montaje mediante
elementos de fijación
Pies de fijación
HNG-...
Brida de fijación
FNG-...
Elementos de fijación adicionales en
el vástago
Cabeza de rótula
SGS-...
Delante Detrás
Caballete
LNZG-...
Brida basculante con pivotes
SNGB-...
Horquilla
SG-...
Caballete
LNG-...
LN-...
Caballete con cojinete esférico
LSN-...
Rótula
FK-...
Brida basculante con pivotes
SNG-...
Caballete con alojamiento esférico
LSNG-...
DetectoresSMTSO-1-PS-S-LED-24
Conjunto de piezas para el montaje
de detectores
SMBT-1
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/056
Cilindros ISO según norma de Opel, n° de referencia M13 01...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Cilindro de doble efectoDOG-...-PPV-A
∅ N° de referencia de Opel M13 01...
[mm]
Carrera
[mm]
Referencia de Festo
Nº de art. Tipo
25 50 80 100 125
32
40
50
63
80
100
125
160
200
250
320
4000
4011
4022
4033
4044
4055
4066
4077
4088
4099
4110
4001
4012
4023
4034
4045
4056
4067
4078
4089
4100
4111
4002
4013
4024
4035
4046
4057
4068
4079
4090
4101
4112
4003
4014
4025
4036
4047
4058
4069
4080
4091
4102
4113
4004
4015
4026
4037
4048
4059
4070
4081
4092
4103
4114
164 430 DOG-32-...-PPV-A
164 431 DOG-40-...-PPV-A
164 432 DOG-50-...-PPV-A
164 433 DOG-63-...-PPV-A
164 434 DOG-80-...-PPV-A
164 435 DOG-100-...-PPV-A
164 436 DOG-125-...-PPV-A
164 437 DOG-160-...-PPV-A
164 438 DOG-200-...-PPV-A
164 439 DOG-250-...-PPV-A
164 440 DOG-320-...-PPV-A
∅ N° de referencia de Opel M13 01...
[mm]
Carrera
[mm]
Referencia de Festo
Nº de art. Tipo
160 200 250 320 400 500
32
40
50
63
80
100
125
160
200
250
320
4005
4016
4027
4038
4049
4060
4071
4082
4093
4104
4115
4006
4017
4028
4039
4050
4061
4072
4083
4094
4105
4116
4007
4018
4029
4040
4051
4062
4073
4084
4095
4106
4117
4008
4019
4030
4041
4052
4063
4074
4085
4096
4107
4118
4009
4020
4031
4042
4053
4064
4075
4086
4097
4108
4119
4010
4021
4032
4043
4054
4065
4076
4087
4098
4109
4120
164 430 DOG-32-...-PPV-A
164 431 DOG-40-...-PPV-A
164 432 DOG-50-...-PPV-A
164 433 DOG-63-...-PPV-A
164 434 DOG-80-...-PPV-A
164 435 DOG-100-...-PPV-A
164 436 DOG-125-...-PPV-A
164 437 DOG-160-...-PPV-A
164 438 DOG-200-...-PPV-A
164 439 DOG-250-...-PPV-A
164 440 DOG-320-...-PPV-A
Ejemplo de pedido:∅ de émbolo de 80 mm, carrera de 160 mm: 164 434 M13 01 4049
Denominación de Opel para un cilindro de∅ de 80 mm y carrera de 160 mm:
Cilindro básico 80 x 160 VDMA 24 562 M13 01 4049
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 7
Cilindros ISO según norma de Opel, n° de referencia M13 01...∅ del émbolo de 32 ... 200 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Cilindro de doble efectocon brida basculante central, forma E
DOGZK-...-PPV-A
∅ N° de referencia de Opel M13 01...
[mm]
Carrera
[mm]
Referencia de Festo
Nº de art. Tipo
25 50 80 100 125
32
40
50
63
80
100
125
160
200
1484
1495
1506
1517
1528
1539
1550
1561
1572
1485
1496
1507
1518
1529
1540
1551
1562
1573
1486
1497
1508
1519
1530
1541
1552
1563
1574
1487
1498
1509
1520
1531
1542
1553
1564
1575
1488
1499
1510
1521
1532
1543
1554
1565
1576
164 441 DOGZK-32-...-PPV-A
164 442 DOGZK-40-...-PPV-A
164 443 DOGZK-50-...-PPV-A
164 444 DOGZK-63-...-PPV-A
164 445 DOGZK-80-...-PPV-A
164 446 DOGZK-100-...-PPV-A
164 447 DOGZK-125-...-PPV-A
164 448 DOGZK-160-...-PPV-A
164 449 DOGZK-200-...-PPV-A
∅ N° de referencia de Opel M13 01...
[mm]
Carrera
[mm]
Referencia de Festo
Nº de art. Tipo
160 200 250 320 400 500
32
40
50
63
80
100
125
160
200
1489
1500
1511
1522
1533
1544
1555
1566
1577
1490
1501
1512
1523
1534
1545
1556
1567
1578
1491
1502
1513
1524
1535
1546
1557
1568
1579
1492
1503
1514
1525
1536
1547
1558
1569
1580
1493
1504
1515
1526
1537
1548
1559
1570
1581
1494
1505
1516
1527
1538
1549
1560
1571
1582
164 441 DOGZK-32-...-PPV-A
164 442 DOGZK-40-...-PPV-A
164 443 DOGZK-50-...-PPV-A
164 444 DOGZK-63-...-PPV-A
164 445 DOGZK-80-...-PPV-A
164 446 DOGZK-100-...-PPV-A
164 447 DOGZK-125-...-PPV-A
164 448 DOGZK-160-...-PPV-A
164 449 DOGZK-200-...-PPV-A
Ejemplo de pedido:∅ de émbolo de 80 mm, carrera de 160 mm: 164 445 M13 01 1533
Denominación de Opel para un cilindro de forma E de∅ de 80 mm y carrera de 160 mm:
Cilindro E 80 x 160 VDMA 24 562 M13 01 1533
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/058
Cilindros ISO según norma de Opel, n° de referencia M13 01...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Cilindro de doble efectoDOG-...-PPV-A
DOG-32 ... 63 DOG-80 ... 320
DOGZK-...-PPV-A
1 Tornillo cilíndrico con hexágono
y rosca interior para fijaciones
2 Tornillo para regular la amorti-
guación en las posiciones finales
3 A partir de∅ 125 con barras
adicionales para el montaje de
los detectores
+ = añadir carrera
+½ = añadir media carrera
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 9
Cilindros ISO según norma de Opel, n° de referencia M13 01...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Cilindro de doble efectoDOG-...-PPV-A
DOGZK-...-PPV-A
∅
[mm]
AM B
∅
d11
BG C2 C3 D4
∅
D5
∅
E EE J2 J3 KK
32 22 30 17 71 86 37 6 50 Gx 7 – M10x1,25
40 24 35 16,5 87 105 45 6 55 G¼ 9,5 2,5 M12x1,25
50 32 40 17 99 117 55 8 65 G¼ 12 5,5 M16x1,5
63 32 45 19,5 116 136 68 8 75 Gy 14 6 M16x1,5
80 40 45 20 136 156 86 10 100 Gy 15 7 M20x1,5
100 40 55 20 164 189 107 10 120 G½ 13 8 M20x1,5
125 54 60 25 192 217 133 12 145 G½ 13 8 M27x2
160 72 65 24 245 280 168 16 186 G¾ 22 22 M36x2
200 72 75 24 295 330 210 16 230 G¾ 22 22 M36x2
250 84 90 25,5 – – 254 18 270 G1 25 25 M42x2
320 96 110 28,5 – – 325 22 340 G1 30 30 M48x2
∅
[mm]
L1 L2 L7 MM
∅
f8
PL RT TD
∅
e9
TG TK TL
32 19 94 ±0,4 5,8 12 8,8 M6 12 32,5 20 12
40 21,5 105 ±0,7 5,3 16 11 M6 16 38 25 16
50 28,5 106 ±0,7 2 20 17,5 M8 16 46,5 28 16
63 28,5 121 ±0,8 5 20 18 M8 20 56,5 30 20
80 34,5 128 ±0,8 8 25 17 M10 20 72 32 20
100 37,5 138 ±0,8 13 25 18 M10 25 89 38 25
125 46 160 ±1 14 32 18 M12 25 110 44 25
160 55 180 ±1,1 – 40 25 M16 32 140 48 32
200 65 180 ±1,6 – 40 28 M16 32 175 48 32
250 67 200 ±2 – 50 31 M20 – 220 – –
320 82 220 ±2 – 63 31 M24 – 240 – –
∅
[mm]
TM UW VA VD WH XG XJ XV ZJ ß1 ß3 ß4
32 50 68 4 10,5 26 62 84 73 120 10 6 –
40 63 72 4 10,5 30 69 96 82,5 135 13 6 –
50 75 86 4 12 37 80 100 90 143 17 8 –
63 90 98 4 12,5 37 87 108 97,5 158 17 8 –
80 110 110 4 16,5 46 101 119 110 174 22 – 17
100 132 136 4 15,5 51 112 128 120 189 22 – 17
125 160 160 6 20,5 65 136 154 145 225 27 – 19
160 200 200 6 – 80 155 185 170 260 36 – 32
200 250 240 6 – 95 165 205 185 275 36 – 32
250 – – 10 – 105 – – – 305 46 – 36
320 – – 10 – 120 – – – 340 55 – 46
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0510
Accesorios para cilindros según norma de Opel, n° de referencia J06 13...Detector para∅ de émbolo de 32 ... 100 mm
SMTSO SMBT
Detector inductivocon LED amarillo y verde, circuito pro-
tector y resistente a interferencias
ocasionadas por campos magnéticos
de soldadura c.a. (resistencia a
soldadura)
SMTSO-1-PS-S-LED-24
Colores de identificación
BK = negro
BN = marrón
BU = azul
-P- Tensión
24 V c.c., 250 V c.a.
-Q- Temperatura
–25 ... +70 °C
– Corriente de conmutación máx.:
200 mA
– Tensión de conexión:
10 ... 30 V corriente continua
– Salida:
PNP
– Clase de protección según
DIN 40 050:
IP 67
– Exactitud reproducible de
conmutación:
± 0,1 mm
Este detector emite una señal eléc-
trica al aproximarse un campo mag-
nético (por ejemplo, del imán perma-
nente del émbolo del cilindro). El es-
tado de conmutación se indica me-
diante un LED amarillo.
Accesorios:
Piezas de fijación
(pedir por separado)
Festo tipo SMBT-1
Detectores AccesoriosN° de referencia
de Opel
Referencia de Festo
Nº de art. Tipo
N° de referencia
de Opel
Referencia de Festo
Nº de art. Tipo
J06 13 0891 30 441 SMTSO-1-PS-S-LED-24 J06 91 0537 150 002 SMBT-1
Ejemplo de pedido: detector resistente a soldadura: 30 441 J06 13 0891
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 11
Accesorios para cilindros según norma de Opel, n° de referencia J06 13...Detector para∅ de émbolo de 32 ... 100 mm
Conectores con cableConector de base, recto Conector de base, acodadoLongitud
[m]
Nº de art. Tipo Nº de art. Tipo
2,5 159 428 SIM-M12-3GD-2,5-PU 159 430 SIM-M12-3WD-2,5-PU Informaciones detalladas sobre losproductos véase DVD y
www.festo.com/catalogue/sim3 30 450 SIM-M12-RS-3GD-3 30 451 SIM-M12-RS-3WD-3
5 159 429 SIM-M12-3GD-5-PU 159 431 SIM-M12-3WD-5-PU
1 LED verde – Preparado
2 LED amarillo – Estado de conmu-
tación
3 conjunto de piezas para el mon-
taje SMBT-1
4 Espacio para el montaje del
conector
5 Punto de conmutación teórico
DetectoresSMTSO-1-PS-S-LED-24
1 Detectores SMTSO-1
Piezas de fijaciónSMBT-1
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0512
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Pies de fijaciónFesto tipo HNG
Dotación del suministro:
2 pies y 4 tornillos
∅
[mm]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40
50
63
80
100
125
160
200
250
320
32 947 HNG-32
32 948 HNG-40
32 949 HNG-50
32 950 HNG-63
32 951 HNG-80
32 952 HNG-100
32 953 HNG-125
34 476 HNG-160
34 477 HNG-200
157 510 HNG-250
157 511 HNG-320
M13 91 1662
M13 91 1663
M13 91 1664
M13 91 1665
M13 91 1666
M13 91 1667
M13 91 1668
M13 91 1669
M13 91 1670
M13 91 1671
M13 91 1672
Ejemplo de pedido: Pies de fijación para∅ de émbolo de 50 mm: 32 949 M13 91 1664
Denominación de Opel para pies de fijación para∅ de émbolo de 50 mm:
Pie de fijación 50 VDMA 24 562 M13 91 1664
+ = añadir carrera
∅
[mm]
Tornillo
cilíndrico
DIN 912
AB
∅
H14
AH AO AT AU SA TR US XA
32 M6x18 7 32 6,5 4 24 142 32 45 144
40 M6x18 10 36 9 4 28 161 36 54 163
50 M8x20 10 45 9,5 5 32 170 45 64 175
63 M8x20 10 50 12,5 5 32 185 50 75 190
80 M10x20 12 63 15 6 41 210 63 93 215
100 M10x20 14,5 71 17,5 6 41 220 75 110 230
125 M12x25 16,5 90 22 8 45 250 90 131 270
160 M16x30 18,5 115 20 10 60 300 115 169 320
200 M16x30 24 135 30 12 70 320 135 214 345
250 M20x40 28 165 35 20 75 350 165 270 380
320 M24x45 35 185 40 23 85 390 200 340 425
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 13
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Dotación del suministro:
1 brida y 4 tornillos
Brida de fijaciónFesto tipo FNG
Delante Detrás
∅
[mm]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40
50
63
80
100
125
160
200
250
320
32 940 FNG-32
32 941 FNG-40
32 942 FNG-50
32 943 FNG-63
32 944 FNG-80
32 945 FNG-100
32 946 FNG-125
34 478 FNG-160
34 479 FNG-200
157 508 FNG-250
157 509 FNG-320
M13 91 1640
M13 91 1641
M13 91 1642
M13 91 1643
M13 91 1644
M13 91 1645
M13 91 1646
M13 91 1647
M13 91 1648
M13 91 1649
M13 91 1650
Ejemplo de pedido: Brida plana para∅ de émbolo de 50 mm: 32 942 M13 91 1642
Denominación de Opel para bridas planas para∅ de émbolo de 50 mm:
Brida plana 50 VDMA 24 562 M13 91 1642
+ = añadir carrera
∅
[mm]
Tornillo
cilíndrico
DIN 912
E FB
∅
MF R TF UF W ZF
32 M6x18 45 7 10 32 64 80 16 130
40 M6x18 54 9 10 36 72 90 20 145
50 M8x20 65 9 12 45 90 110 25 155
63 M8x20 75 9 12 50 100 120 25 170
80 M10x20 93 12 16 63 126 150 30 190
100 M10x20 110 14 16 75 150 175 35 205
125 M12x25 140 16 20 90 180 220 45 245
160 M16x30 180 18 20 115 230 280 60 280
200 M16x30 220 22 25 135 270 320 70 300
250 M20x30 270 26 25 165 330 390 80 330
320 M24x40 340 33 30 200 400 470 90 370
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0514
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
CaballeteFesto tipo LNZG
Para montaje de la brida basculante
central
Dotación del suministro:
2 unidades
∅
[mm]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40/50
63/80
100/125
160/200
250
320
32 959 LNZG-32
32 960 LNZG-40/50
32 961 LNZG-63/80
32 962 LNZG-100/125
35 780 LNZG-160/200
157 516 LNZG-250
157 517 LNZG-320
M13 91 2310
M13 91 2311
M13 91 2312
M13 91 2313
M13 91 2314
M13 91 2315
M13 91 2316
Ejemplo de pedido: apoyo para∅ de émbolo de 50 mm: 32 960 M13 91 2311
Denominación de Opel para un conjunto de apoyos para∅ de émbolo de 50 mm:
Apoyos 40/50 VDMA 24 562 M13 91 2311
∅
[mm]
CR
∅
DA
∅
H13
FK
∅
FN FS H1 HB
∅
H13
KE NH TH
±0,1
UL
32 12 D11 11 15 ±0,1 30 10,5 15 6,6 6,8 18 32 46
40 16 D11 15 18 ±0,1 36 12 18 9 9 21 36 55
50 16 D11 15 18 ±0,1 36 12 18 9 9 21 36 55
63 20 D11 18 20 ±0,1 40 13 20 11 11 23 42 65
80 20 D11 18 20 ±0,1 40 13 20 11 11 23 42 65
100 25 D11 20 25 ±0,1 50 16 24,5 14 13 28,5 50 75
125 25 D11 20 25 ±0,1 50 16 24,5 14 13 28,5 50 75
160 32 D11 26 30 ±0,2 60 22,5 36 18 17 40 60 92
200 32 D11 26 30 ±0,2 60 22,5 36 18 17 40 60 92
250 40 G7 33 35 ±0,2 70 27,5 45 22 21,5 50 90 140
320 50 G7 40 40 ±0,2 80 32,5 55 26 25,5 60 100 150
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 15
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Para caballetes LN, LNG y LSN-...
Dotación del suministro de SNGB:
1 brida basculante, 1 perno con
seguro y 4 tornillos de fijación
Brida basculanteFesto tipo SNGB
∅
[mm]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40
50
63
80
100
125
160
200
250
320
34 540 SNGB-32
34 541 SNGB-40
34 542 SNGB-50
34 543 SNGB-63
34 544 SNGB-80
34 545 SNGB-100
34 546 SNGB-125
34 547 SNGB-160
562 455 SNGB-200-B
157 512 SNGB-250
157 513 SNGB-320
M13 91 1651
M13 91 1652
M13 91 1653
M13 91 1654
M13 91 1655
M13 91 1656
M13 91 1657
M13 91 1658
M13 91 1659
M13 91 1660
M13 91 1661
Ejemplo de pedido: brida basculante para∅ de émbolo de 50 mm: 34 542 M13 91 1653
Denominación de Opel para bridas basculantes para∅ de émbolo de 50 mm:
Brida basculante 50 VDMA 24 562 M13 91 1653
+ = añadir carrera
∅
[mm]
Tornillo
cilíndrico
DIN 912
CB
H14
CD
∅
FL L ML MR UB
h14
XC
32 M6x18 26 10 22 13 55 10 45 142
40 M6x18 28 12 25 16 63 12 52 160
50 M8x20 32 12 27 16 71 12 60 170
63 M8x20 40 16 32 21 83 16 70 190
80 M10x20 50 16 36 22 103 16 90 210
100 M10x20 60 20 41 27 127 20 110 230
125 M12x25 70 25 50 30 148 25 130 275
160 M16x30 90 30 55 35 188 25 170 315
200 M16x30 90 30 60 35 188 25 170 335
250 M20x30 110 40 70 47 231 40 200 375
320 M24x40 120 45 80 52 253 45 220 420
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0516
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Caballete, fijoFesto tipo LNG, LN
Para brida basculante SNGB-...
Dotación del suministro:
1 caballete
∅
[mm]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40
50
63
80
100
125
160
200
250
320
33 890 LNG-32
33 891 LNG-40
33 892 LNG-50
33 893 LNG-63
33 894 LNG-80
33 895 LNG-100
33 896 LNG-125
9 037 LN-160
33 898 LNG-200
9 039 LN-250
9 040 LN-320
M13 91 1101
M13 91 1102
M13 91 1103
M13 91 1104
M13 91 0924
M13 91 1105
M13 91 1106
M13 91 1107
M13 91 1108
M13 91 1109
M13 91 1358
Ejemplo de pedido: caballete fijo para∅ de émbolo de 50 mm: 33 892 M13 91 1103
Denominación de Opel para un caballete fijo para∅ de émbolo de 50 mm:
Caballete fijo 50 VDMA 24 562 M13 91 1103
∅
[mm]
BR BT CK
∅
EB
∅
H13
EM GL HB
∅
H13
OF PH RA TE UL UR
32 10 8 10 D11 – 25,8 –0,4 21 5,5 – 32 18 38 51 31
40 11 10 12 D11 – 27,8 –0,4 24 5,5 – 36 22 41 54 35
50 12 12 12 D11 – 31,8 –0,4 33 6,5 – 45 30 50 65 45
63 14,5 12 16 D11 15 40 c11 37 6,6 10,8 50 35 52 67 51
80 14,5 14 16 D11 20 50 c11 47 9 12,7 63 40 66 86 60
100 18,5 15 20 D11 20 60 c11 55 9 13,7 71 50 76 96 70
125 22 20 25 D11 20 70 c11 70 11 18,6 90 60 94 124 90
160 31 25 30 H8 20 90 c11 97 14 23,6 115 88 118 156 126
200 31 30 30 D11 26 90 c11 105 18 28,5 135 90 122 162 130
250 38,5 35 40 H8 33 110 c11 128 22 33,5 165 110 150 200 160
320 44,5 40 45 H8 40 120 c11 150 26 38,3 200 122 170 234 186
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 17
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Para brida basculante SNGB-...
Dotación del suministro:
1 caballete y 2 casquillos
Caballetecon cojinete esférico
Festo tipo SLN
∅
[mm]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40
50
63
80
100
125
160
200
250
320
5 561 LSN-32
5 562 LSN-40
5 563 LSN-50
5 564 LSN-63
5 565 LSN-80
5 566 LSN-100
6 987 LSN-125
6 988 LSN-160
6 989 LSN-200
6 990 LSN-250
6 991 LSN-320
M13 91 1223
M13 91 1359
M13 91 1287
M13 91 1285
M13 91 1286
M13 91 1360
M13 91 1361
M13 91 1362
M13 91 1363
M13 91 1364
M13 91 1365
Ejemplo de pedido: caballete con cojinete esférico para∅ de émbolo de 50 mm: 5 563 M13 91 1287
Denominación de Opel para un caballete con cojinete esférico para∅ de émbolo de 50 mm:
Caballete 50 VDMA 24 562 M13 91 1287
∅
[mm]
BR BT CK
∅
H7
EB
∅
EM GL HB
∅
LE OF PH RA TE UL UR
32 13 8 10 10 25,8 21 5,5 16 4,5 32 18 38 51 31
40 15 10 12 10 27,8 24 5,5 20 4,3 36 22 41 54 35
50 15 12 12 11 31,8 33 6,6 22 5,2 45 30 50 65 45
63 20 12 16 11 39,8 37 6,6 30 5,2 50 35 52 67 50
80 20 14 16 15 49,8 47 9 31 5 63 40 66 86 60
100 24 15 20 15 59,8 55 9 38 6 71 50 76 96 70
125 33 20 25 22 69,8 70 11 – 18 90 60 94 124 90
160 36 28 30 26 89,8 97 13,5 – 22 115 88 118 156 126
200 36 30 30 30 89,8 105 16 – 27 135 90 122 162 130
250 43 35 40 40 109,5 128 22 – 32 165 110 150 200 160
320 54 40 45 48 119,8 150 26 – 37 200 122 170 234 186
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0518
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 200 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Brida basculanteFesto tipo SNG
Para caballete LSNG-...
Dotación del suministro:
1 brida basculante, 1 perno con
seguro y 4 tornillos de fijación
∅
[mm]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40
50
63
80
100
125
160
200
32 968 SNG-32
32 969 SNG-40
32 970 SNG-50
32 971 SNG-63
32 972 SNG-80
32 973 SNG-100
32 974 SNG-125
152 597 SNG-160
152 598 SNG-200
M13 91 1673
M13 91 1674
M13 91 1675
M13 91 1676
M13 91 1677
M13 91 1678
M13 91 1679
M13 91 1680
M13 91 1681
Ejemplo de pedido: brida basculante para∅ de émbolo de 50 mm: 32 970 M13 91 1675
Denominación de Opel para bridas basculantes para∅ de émbolo de 50 mm:
Brida basculante 50 VDMA 24 562 M13 91 1675
1 El bulón está provisto de un pa-
sador elástico para evitar que
gire
+ = añadir carrera
∅
[mm]
Tornillo
cilíndrico
DIN 912
CG
H14
CP
d12
EK
∅
FL L SR XC
32 M6x18 14 34 10 22 13 11 142
40 M6x18 16 40 12 25 16 13 160
50 M8x20 21 45 16 27 16 15 170
63 M8x20 21 51 16 32 21 18 190
80 M10x20 25 65 20 36 22 20 210
100 M10x20 25 75 20 41 27 22 230
125 M12x25 37 97 30 50 30 26 275
160 M16x30 43 122 35 55 35 32 315
200 M16x30 43 122 35 55 35 32 335
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 19
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 200 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Para brida basculante SNG-...
Dotación del suministro:
1 caballete
Caballete con cojinete esféricoFesto tipo LSNG
∅
[mm]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40
50
63
80
100
125
160
200
31 740 LSNG-32
31 741 LSNG-40
31 742 LSNG-50
31 743 LSNG-63
31 744 LSNG-80
31 745 LSNG-100
31 746 LSNG-125
152 599 LSNG-160
152 600 LSNG-200
M13 91 1684
M13 91 1685
M13 91 1686
M13 91 1687
M13 91 1688
M13 91 1689
M13 91 1690
M13 91 1691
M13 91 1692
Ejemplo de pedido: caballete con cojinete esférico para∅ de émbolo de 50 mm: 31 742 M13 91 1686
Denominación de Opel para un caballete con cojinete esférico para∅ de émbolo de 50 mm:
Caballete 50 VDMA 24 562 M13 91 1686
∅
[mm]
BR BT CN
∅
EB
∅
EN EU GL HB
∅
LE OF PH RA TE UL UR
32 15 10 10 11 14 10,5 21 6,6 16 9 32 18 38 51 31
40 17 10 12 11 16 12 24 6,6 20 9 36 22 41 54 35
50 20 12 16 14 21 15 33 9 24 11 45 30 50 65 45
63 22 12 16 14 21 15 37 9 27 11 50 35 52 67 50
80 27 14 20 17 25 18 47 11 31 12,5 63 40 66 86 60
100 29 15 20 17 25 18 55 11 38 13,5 71 50 76 96 70
125 39 20 30 19 37 25 70 14 50 18,5 90 60 94 124 90
160 42 28 35 20 43 28 97 14 45 25,5 115 88 118 156 126
200 42 35 35 26 43 28 97 18 45 31,8 135 88 122 162 130
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0520
Accesorios para cilindros según norma de Opel, n° de referencia M37 23...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Cabeza de rótulaFesto tipo SGS
Dotación del suministro:
1 cabeza de rótula con tuerca hexago-
nal DIN 439
Según DIN 648 serie K con tuerca
hexagonal según DIN 439
Las cabezas de rótula no precisan
mantenimiento gracias a la combina-
ción de acero, bronce y PTFE en el
cojinete.
∅
[mm]
Rosca del vástago Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40
50/63
80/100
125
160/200
250
320
M6
M8
M10
M10x1,25
M12
M12x1,25
M16
M16x1,5
M20x1,5
M27x2
M36x2
M42x2
M48x2
9 254 SGS-M6
9 255 SGS-M8
9 256 SGS-M10
9 261 SGS-M10x1,25
9 257 SGS-M12
9 262 SGS-M12x1,25
9 258 SGS-M16
9 263 SGS-M16x1,5
9 264 SGS-M20x1,5
10 774 SGS-M27x2
10 775 SGS-M36x2
10 776 SGS-M42x2
10 777 SGS-M48x2
M37 23 0251
M37 23 0252
M37 23 0253
M37 23 0307
M37 23 0254
M37 23 0198
M37 23 0257
M37 23 0258
M37 23 0260
M37 23 0308
M37 23 0309
M37 23 0310
M37 23 0311
Ejemplo de pedido: cabeza de rótula para∅ de émbolo de 50 mm: 9 263 M37 23 0258
Denominación de Opel para cabeza de rótula para∅ de émbolo de 50 mm:
Cabeza de rótula M16x1,5 M37 23 0258
Tuerca hexagonal
DIN 439
∅
[mm]
AV B1 CE CN
∅
H7
D1
∅
EF EN EU KK z ß1 ß2
– 12 3,2 30 6 13 10 9 6,8 M6 13 10 11
– 16 4 36 8 16 12 12 9 M8 13 13 14
25/32 20 5 43 10 19 14 14 10,5 M10 13 16 17
M10x1,25 17
40 22 6 50 12 22 16 16 12 M12 13 18 19
M12x1,25 19
50/63 28 8 64 16 27 21 21 15 M16 15 24 22
M16x1,5
80/100 33 10 77 20 34 25 25 18 M20x1,5 15 30 30
125 51 13,5 110 30 50 35 37 25 M27x2 15 41 41
160/200 56 18 125 35 58 40 43 28 M36x2 15 55 50
250 65 21 142 40 65 45 49 33 M42x2 15 65 55
320 75 24 160 50 75 57,5 60 45 M48x2 15 75 65
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 21
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 320 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
Dotación del suministro:
1 horquilla con tuerca hexagonal
según DIN 439 y 1 perno con seguro
Montado en fábrica.
Para fijación giratoria del cilindro
mediante horquilla.
La horquilla se monta en el extremo
delantero del vástago y permite un
movimiento giratorio del cilindro en
un plano.
HorquillaFesto tipo SG
∅
[mm]
Rosca del
vástago
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel DIN
ISO
8140
DIN
7152
32
40
50/63
80/100
125
160/200
250
320
M10x1,25
M12x1,25
M16x1,5
M20x1,5
M27x2
M36x2
M42x2
M48x2
6 144 SG-M10x1,25
6 145 SG-M12x1,25
6 146 SG-M16x1,5
6 147 SG-M20x1,5
14 987 SG-M27x2-B
9 581 SG-M36x2
9 582 SG-M42x2
9 583 SG-M48x2
M13 91 1062
M13 91 0452
M13 91 1059
M13 91 1034
M13 91 1096
M13 91 1057
M13 91 1097
M13 91 1098
X
X
X
X
X
X
X
X
X
X
X
–
–
–
–
–
Ejemplo de pedido: horquilla para∅ de émbolo de 50 mm: 6 146 M13 91 1059
Denominación de Opel para horquilla para∅ de émbolo de 50 mm:
Horquilla M16x1,5 M13 91 1059
Tuerca hexagonal
DIN 439
∅
[mm]
B1 B2 B3 CE
±0,4
CK
∅
H9
CM CV D1
∅
KK LE
±0,5
ß1
32 5 26 20 40 10 10 12 18 M10x1,25 20 17
40 6 31 24 48 12 12 14 20 M12x1,25 24 19
50/63 8 39 32 64 16 16 19 26 M16x1,5 32 24
80/100 10 54 40 80 20 20 25 34 M20x1,5 40 30
125 13,5 74 55 110 30 30 38 48 M27x2 54 41
160/200 18 92 70 144 35 35 44 60 M36x2 72 55
250 21 111 85 168 40 40 64 70 M42x2 84 65
320 24 123 90 192 50 50 73 80 M48x2 96 75
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0522
Accesorios para cilindros según norma de Opel, n° de referencia M13 91...∅ del émbolo de 32 ... 200 mm, según ISO 6431, VDMA 24 562 y NF E 49 003.1
RótulaFesto tipo FK
Con tuerca hexagonal según DIN 439.
La rótula se utiliza para unir el ex-
tremo del vástago de los cilindros con
diversas partes móviles de máquinas.
La rótula corrige desviaciones radia-
les y angulares (errores de alinea-
ción).
Dotación del suministro:
1 rótula con tuerca hexagonal
∅
[mm] Rosca del vástago
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
32
40
50/63
80/100
125
160/200
M6
M8
M10
M10x1,25
M12x1,25
M16
M16x1,5
M20
M20x1,5
M27x2
M36x2
2 061 FK-M6
2 062 FK-M8
2 063 FK-M10
6 140 FK-M10x1,25
6 141 FK-M12x1,25
2 065 FK-M16
6 142 FK-M16x1,5
2 066 FK-M20
6 143 FK-M20x1,5
10 485 FK-M27x2
10 746 FK-M36x2
M13 91 0394
M13 91 0075
M13 91 0274
M13 91 1095
M13 91 1040
M13 91 0076
M13 91 0808
M13 91 0077
M13 91 0275
M13 91 1099
M13 91 1100
Ejemplo de pedido: rótula para∅ de émbolo de 50 mm: 6 142 M13 91 0808
Denominación de Opel para rótula para∅ de émbolo de 50 mm:
rótula M16x1,5 M13 91 0808
Compensación angular
Compensación radial del eje central
∅
[mm]
B1 D1
∅
D2
∅
D3
∅
L1 L2 L3 L4 L5 L6 KK ß1 ß2 ß3 ß4
– 3,2 8,5 14,5 5,8 37 25 4,4 17,5 11,5 15,7 M6 7 13 5 10
– 4 12,5 19 7,8 49 34 6 23,5 14 20,5 M8 10 17 7 13
32 5 21,8 32 13,8 67,5 49,5 9 34 23 31 M10 19 30 12 17
69,5 M10x1,25
40 6 21,8 32 13,8 74,5 50,5 10 34 24 32 M12x1,25 19 30 12 19
50/63 8 33,8 45 22 97 71 10 53 32 44,5 M16 30 41 19 24
103 M16x1,5
80/100 10 33,8 45 25 120 80 19 53 41 53,5 M20 30 41 19 30
M20x1,5
125 13,5 – 62 28 157 103 12,2 79 42 62,6 M27x2 55 55 24 41
160/200 18 – 80 36 251 179 22 136 78 110 M36x2 75 75 32 55
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 23
Válvulas ISO según norma de OpelÍndice
Válvulas normalizadas
Referencia Tipo de Festo N° de referen-
cia de Opel
Pá-
gina
Electroválvulas con
distribución de agujeros según
ISO 5599/1
tamaños ISO 1, 3 y 4
MDH-5/2-...
JMDH-5/2-...
MDH-5/3...
M32 ... 24
Electroválvulas con
distribución de agujeros según
ISO 15407-1
Tamaños 01 y 02
VSVA-... M32 ... 28
Accesorios para válvulasReferencia Tipo de Festo N° de referen-
cia de Opel
Pá-
gina
Conectores
según DIN EN 175301-803
MSSD-...
KMEB-...
MEB-...
M32 91 ... 32
Placas de enlace con
distribución de agujeros según
ISO 5599/1
Dimensiones exteriores según
VDMA 24 345
tamaños ISO 1, 3 y 4
NAS-...
NAV-...
NEV-...
NDV-...
NSC-...
NZV-...
M32 91 ... 34
Placas de enlace con
distribución de agujeros según
ISO 15407-1
Tamaños 01 y 02
NAS-...
NAW-...
NEV-...
NZV-...
NDV-...
35
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0524
Válvulas ISO según norma de Opel, n° de referencia M32 ...Válvula neumática, tamaño 1 (G¼), tamaño 3 (G½) y tamaño 4 (G¾) con distribución de agujeros según ISO 5599/1
ElectroválvulaFesto tipo MDH
Electroválvula biestableFesto tipo JMDH
-M- Caudal
Tamaño 1
1200 l/min
Tamaño 3
4100 ... 4600 l/min
Tamaño 4
6000 l/min
-P- Tensión
24 V c.c.
230 V c.a.
24 V c.c./42 V c.a.
-L- Presión de funcionamiento
2 ... 16 bar
-Q- Temperatura
Temperatura ambiente
–10 ... +50 °C
Temperatura del fluido
–10 ... +60 °C
– Fluido:
Aire comprimido lubricado o sin
lubricar
– Exenta de mantenimiento
– Exenta de solapamiento
– Sin silicona1)
– Tornillos de fijación imperdibles
– Accionamiento manual auxiliar con
reposición automática
– Clase de protección con conector
IP 65
– ED 100%
– 3 tensiones:
24 V c.c.,
potencia nominal 6,8 W
230 V c.a./50 Hz,
potencia de retención 10,5 VA
24 V c.c./42 V c.a./50 Hz,
potencia de retención 12,2 VA
Accesorios:
Conectores según norma de Opel y
norma DIN EN 175301-803, con indi-
cación de accionamiento de color
verde y con cuerpo transparente:
Tipo A con racor PG gris
(para conexión 14).
Tipo B con racor PG negro
(para conexión 12).
Conectores: pedir por separado
ver página 32
Placas de enlace para válvulas,
ver página 34
1) Sin substancias que interfieren en la pintura
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 25
Válvulas ISO según norma de Opel, n° de referencia M32 ...Válvula neumática, tamaño 1 (G¼), tamaño 3 (G½) y tamaño 4 (G¾) con distribución de agujeros según ISO 5599/1
Datos técnicos
Símbolo Tamaño ISO
Código ISO
Opel N° de
referencia
Tensión Diá-
metro
nomi-
nal
[mm]
Caudal nominal
1 > 2, 1 > 4
[l/min]
Presión
de fun-
ciona-
miento
[bar]
Tiempo de
conmutación
con 6 bar
Con./Des.
[ms]
Referencia de Festo
Nº de art. Tipo
1 52 M32 15 0296 24 V c.c./42 V c.a. 8 1200 3 ... 16 18/40 43 281 MDH-5/2-D-1-FR-C
M32 15 0297 230 V c.a. 43 282 MDH-5/2-D-1-FR-C
3 52 M32 15 0298 24 V c.c./42 V c.a. 14,5 4500 3 ... 16 28/68 43 289 MDH-5/2-D-3-FR-C
M32 15 0299 230 V c.a. 43 290 MDH-5/2-D-3-FR-C
4 52 M32 15 0300 24 V c.c./42 V c.a. 18 6000 3 ... 16 53/85 35 636 MDH-5/2-D-4-24-FR
M32 15 0301 230 V c.a. 35 636 MDH-5/2-D-4-230-FR
1 55 M32 15 0302 24 V c.c./42 V c.a. 8 1200 2 ... 16 16/16 43 283 JMDH-5/2-D-1-C
M32 15 0303 230 V c.a. 43 284 JMDH-5/2-D-1-C
3 55 M32 15 0304 24 V c.c./42 V c.a. 14,5 4500 2 ... 16 21/21 43 291 JMDH-5/2-D-3-C
M32 15 0305 230 V c.a. 43 292 JMDH-5/2-D-3-C
4 55 M32 15 0306 24 V c.c./42 V c.a. 18 6000 2 ... 16 40/40 35 942 JMDH-5/2-D-4-24
M32 15 0307 230 V c.a. 35 942 JMDH-5/2-D-4-230
1 56 M32 18 0078 24 V c.c./42 V c.a. 8 1200 3 ... 16 18/41 43 285 MDH-5/3G-D-1-C
M32 18 0079 230 V c.a. 43 286 MDH-5/3G-D-1-C
3 56 M32 18 0082 24 V c.c./42 V c.a. 14,5 4100 3 ... 16 35/79 43 293 MDH-5/3G-D-3-C
M32 18 0083 230 V c.a. 43 294 MDH-5/3G-D-3-C
1 57 M32 18 0080 24 V c.c./42 V c.a. 8 1200 3 ... 16 18/43 43 287 MDH-5/3E-D-1-C
M32 18 0081 230 V c.a. 43 288 MDH-5/3E-D-1-C
3 57 M32 18 0084 24 V c.c./42 V c.a. 14,5 4600 3 ... 16 36/84 43 295 MDH-5/3E-D-3-C
M32 18 0085 230 V c.a. 43 296 MDH-5/3E-D-3-C
Ejemplo de pedido: electroválvula de 5/2 vías apropiada para tensiones de 24 V c.c. y 42 V c.a.:MDH-5/2-D-4-24-FR 35 636 M32 15 0300
Denominación de Opel para una válvula de 5/2 vías, tamaño ISO 4, monoestable, con bobina de 24/42 voltios:
Válvula de 5/2 vías 4 - 24/42 V - M32 15 0300es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0526
Válvulas ISO según norma de Opel, n° de referencia M32 ...Válvula neumática, tamaño 1 (G¼), tamaño 3 (G½) y tamaño 4 (G¾) con distribución de agujeros según ISO 5599/1
ElectroválvulaMDH-5/2-...
Válvula de 5/2 víastamaños ISO 1 y 3
Electroválvula biestableJMDH-5/2...
Válvula de 5/2 víastamaños ISO 1 y 3
ElectroválvulaMDH-5/3...Válvula de 5/3 vías
tamaños ISO 1 y 3
1 Distribución de conexiones
según DIN EN 175301-803
2 Accionamiento manual auxiliar
3 Tornillos imperdibles
Tipo B1 B2 B3 B4 D1 H1 H2 H3 H4 H5 L1 L2 L3 L4 L5 L6
tamaño ISO 1
MDH-5/2-D-1-FR-C
42 28 6 30 M5 103 74,2 38 9 46,5
98 43,8
36 18 91,5JMDH-5/2-D-1-C 156 87,6 43,8
MDH-5/3...-D-1-C 108,4 54,2
tamaño ISO 3
MDH-5/2-D-3-FR-C
65 48 12 30 M8 120 91,2 55 12 63,5
164,7 72,7
64 32 111JMDH-5/2-D-3-C 194,4 145,4 72,7
MDH-5/3...-D-3-C 184 92
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 27
Válvulas ISO según norma de Opel, n° de referencia M32 ...Válvula neumática, tamaño 1 (G¼), tamaño 3 (G½) y tamaño 4 (G¾) con distribución de agujeros según ISO 5599/1
ElectroválvulaMDH-5/2-...
Válvula de 5/2 víastamaño ISO 4
Electroválvula biestableJMDH-5/2-...
Válvulas de 5/2 víastamaño ISO 4
1 Distribución de conexiones
según DIN EN 175301-803
2 Accionamiento manual auxiliar
3 Tornillos imperdibles
4 Bobina girable en 90 ° indepen-
dientemente del accionamiento
manual auxiliar
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0528
Válvulas normalizadas según norma de Opel, n° de referencia M32 ...Electroválvulas, tamaño 01 (G¼) y tamaño 02 (Gx) con distribución de agujeros según ISO 15407-1
ElectroválvulaFesto tipo VSVA
-M- Caudal
Tamaño 01
1000 ... 1100 l/min
Tamaño 02
450 ... 550 l/min
-P- Tensión
24 V c.c.
230 V c.a./50 Hz
-L- Presión de funcionamiento
2 ... 10 bar
-Q- Temperatura
Temperatura ambiente
–5 ... +50 °C
Temperatura del fluido
–5 ... +50 °C
– Fluido:
Aire comprimido lubricado o sin
lubricar
– Exenta de mantenimiento
– Exenta de solapamiento
– Sin silicona1)
– Interface eléctrico según
DIN EN 175301-803
– Clase de protección con conector
IP 65
– ED 100%
– 2 tensión:
24 V c.c.,
potencia nominal 1,8 W
230 V c.a./50 Hz,
potencia de retención 2,1 VA
Uso versátil
Montaje sencillo
– Tornillos de fijación y juntas imper-
dibles
Montaje rápido
– Sólo 2 tornillos de fijación
Aire de descarga
– Descarga común central
– Descarga común de pilotajes
Utilización sencilla
– No es necesario desmontar los
tubos flexibles al cambiar la
válvula
Accesorios:
Conectores según norma de Opel y
DIN EN 175301-803.
Conectores: pedir por separado
ver página 32
Placas de enlace para válvulas,
ver página 34
1) Sin substancias que interfieren en la pintura
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 29
Válvulas normalizadas según norma de Opel, n° de referencia M32 ...Electroválvulas, tamaño 01 (G¼) y tamaño 02 (Gx) con distribución de agujeros según ISO 15407-1
Datos técnicos
Símbolo Tamaño ISO
Código ISO
Opel N° de
referencia
Tensión Diá-
metro
nomi-
nal
[mm]
Caudal nominal
1 > 2, 1 > 4
[l/min]
Presión de
funciona-
miento
[bar]
Tiempo de
conmutación
con 6 bar
Con./Des.
[ms]
Referencia de Festo
Nº de art. Tipo
01 52 M32 15 0420 24 V c.c. 9 1100 3 ... 10 26/56 546 702 VSVA-B-M52-MH-A1-1C1
M32 15 0421 230 V c.a. 547 220 VSVA-B-M52-MH-A1-3AC1
02 52 M32 15 0424 24 V c.c. 5 550 3 ... 10 17/35 546 703 VSVA-B-M52-MH-A2-1C1
M32 15 0425 230 V c.a. 547 221 VSVA-B-M52-MH-A2-3AC1
01 55 M32 15 0422 24 V c.c. 9 1100 2 ... 10 18/18 546 696 VSVA-B-B52-H-A1-1C1
M32 15 0423 230 V c.a. 547 214 VSVA-B-B52-H-A1-3AC1
02 55 M32 15 0426 24 V c.c. 5 550 2 ... 10 15/15 546 697 VSVA-B-B52-H-A2-1C1
M32 15 0427 230 V c.a. 547 215 VSVA-B-B52-H-A2-3AC1
01 56 M32 18 0114 24 V c.c. 9 1000 3 ... 10 23/58 546 708 VSVA-B-P53C-H-A1-1C1
M32 18 0115 230 V c.a. 547 226 VSVA-B-P53C-H-A1-3AC1
02 56 M32 18 0118 24 V c.c. 5 450 3 ... 10 18/30 546 709 VSVA-B-P53C-H-A2-1C1
M32 18 0119 230 V c.a. 547 227 VSVA-B-P53C-H-A2-3AC1
01 57 M32 18 0116 24 V c.c. 9 1000 3 ... 10 23/58 546 706 VSVA-B-P53E-H-A1-1C1
M32 18 0117 230 V c.a. 547 224 VSVA-B-P53E-H-A1-3AC1
02 57 M32 18 0120 24 V c.c. 5 450 3 ... 10 18/30 546 707 VSVA-B-P53E-H-A2-1C1
M32 18 0121 230 V c.a. 547 225 VSVA-B-P53E-H-A2-3AC1
Ejemplo de pedido: válvula de 5/2 vías para tensión de 24 V c.c.: VSVA-B-M52-MH-A1-1C1 546 702 M32 15 0420
Denominación de Opel para una válvula de 5/2 vías, tamaño ISO 01, monoestable, con bobina de 24 voltios:
Válvula de 5/2 vías 01 - 24 V - M32 15 0420
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0530
Válvulas normalizadas según norma de Opel, n° de referencia M32 ...Válvula neumática, tamaño 01 (G¼), tamaño 02 (Gx) con distribución de agujeros según ISO 15407-1
ElectroválvulaVSVA-B-M52...
Válvula de 5/2 vías, monoestable
1 Toma para conector con distribu-
ción según DIN EN 175301-803
forma C
2 Accionamiento manual auxiliar
3 Tornillos imperdibles
4 Ranura para placa de identifica-
ción
Tipo B1 B2 D1 H1 H2 H3 H4 H5 L1 L2 L3 L4 L5
ISO tamaño 01
VSVA-B-M52... 26,3 19 M4 89,2 71,2 62,6 39,3 7 113,1 63,1 29,75 61,6 123,2
ISO tamaño 02
VSVA-B-M52... 18 12,5 M3 80,6 62,2 53,6 30,3 5,4 95,4 53,9 21,25 53,1 102,2
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 31
Válvulas normalizadas según norma de Opel, n° de referencia M32 ...Válvula neumática, tamaño 01 (G¼), tamaño 02 (Gx) con distribución de agujeros según ISO 15407-1
ElectroválvulaVSVA-B-M52...
Válvula de 5/2 vías, biestable,Válvula de 5/3 vías
1 Toma para conector con distribu-
ción según DIN EN 175301-803
forma C
2 Accionamiento manual auxiliar
3 Tornillos imperdibles
4 Ranura para placa de identifica-
ción
Type B1 B2 D1 H1 H2 H3 H4 H5 L1 L2 L3 L4 L5
ISO tamaño 01
VSVA-B-M52... 26,3 19 M4 89,2 71,2 62,2 39,3 7 126,2 63,1 29,75 61,6 123,2
ISO tamaño 02
VSVA-B-M52... 18 12,5 M3 80,6 62,2 53,6 30,3 5,4 107,8 53,9 21,25 53,1 102,2
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0532
Accesorios para válvulas según norma de Opel, n° de referencia M32 91...Conectores según DIN EN 175301-803
KMEB MEBMSSD-EB MSSD-C
ConectorFesto tipo MSSD
Conector con cableFesto tipo KMEBJunta reflectante
Festo tipo MEB
– Conectores MSSDcon distribución de conexiones
según DIN EN 175301-803
– Con cuerpo transparente, junta
perfilada y LED verde
– Clase de protección IP 65
– Conectores con cable KMEBcon distribución de conexiones
según DIN EN 175301-803
– Cables de 2,5 m y 5 m
– Clase de protección IP 65
– Junta reflectante MEDcon LED amarillo
– Clase de protección IP 65
– Circuito protector
Informaciones detalladas sobre losproductos véase DVD ywww.festo.com/catalogue/<type>
Conector DIN EN 175301-803
para válvulas según
ISO 5599/1
Tensión Longitud Racor de cable/Color N° de referencia
de Opel
Tipo Referencia de Festo
Nº de art. Tipo
Forma A con LED verde
Cuerpo transparente
24 V c.c. – Pg11/gris M32 91 2648 A** 35 945 MSSD-C14-TG-24=Opel
Pg11/negro M32 91 2649 B*** 35 944 MSSD-C12-TS-24=Opel
Forma A con LED verde
Cuerpo transparente
230 V c.a. – Pg11/gris M32 91 2242 A** 35 949 MSSD-C14-TG-230~Opel*
Pg11/negro M32 91 2243 B*** 35 948 MSSD-C12-TS-230~Opel*
Forma A sin LED – – Pg9/negro M32 91 0349 B*** 34 583 MSSD-C
Conector DIN EN 175301-803
para válvulas según
VDMA 24 563
Forma C, junta plana – – Pg7 – – 151 687 MSSD-EB
Forma C con LED amarillo
Circuito protector
24 V c.c. 2,5 m – – – 151 688 KMEB-1-24-2,5-LED
5 m – – 151 689 KMEB-1-24-5-LED
Forma C
Sin LED
230 V c.a. 2,5 m – – – 151 690 KMEB-1-230-2,5
5 m – – 151 691 KMEB-1-230-5
Junta reflectante 24 V c.c. – – – – 151 717 MEB-LD-12-24
230 V c.a. – – 151 718 MEB-LD-230
* sobre consulta ** Tipo A para conexión de válvula 14 *** Tipo B para conexión de válvula 12
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 33
Accesorios para válvulas según norma de Opel, n° de referencia M32 91...Conectores según DIN EN 175301-803
12 ... 24 V 230 V Esquemas de conexión
1 Elementos girables en 90°
ConectorMSSD-C14-TG-...
MSSD-C12-TS-...
1 Elementos girables en 90°
ConectorMSSD-C14-C
MSSD-C
1 Elementos girables en 90°
ConectorMSSD-EB
3 Campo de iluminación LED
5 Esquema de conexiones
8 Clip de identificación
aB Distribución de conexiones
según DIN EN 175301-803
aC Cable de 3 x 0,5 mm2
Conector con cableKMEB-...
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0534
Accesorios para válvulas según norma de Opel, n° de referencia M32 91...Placas de enlace ISO, tamaño 1 (G¼), tamaño 3 (G½ y tamaño 4 (G¾) con distribución de agujeros según ISO 5599/1 y dimensiones exteriores según VDMA 24 345
Placas de enlaceISO 5599/1
Denominación Tamaño N° de referencia de Opel Nº de art. Tipo
Placa base individual
Conexiones laterales
Forma A
1 M32 91 2221 9 484 NAS-¼-1A-ISO
3 M32 91 2224 10 336 NAS-½-3A-ISO
4 M32 91 2227 152 813 NAS-¾-4A-ISO
Placa base en serie
(placa de enlace)
Forma C
1 M32 91 2222 10 173 NAV-¼-1C-ISO
3 M32 91 2225 10 175 NAV-½-3C-ISO
4 M32 91 2228 11 139 NAV-¾-4C-ISO
Conjunto de placas finales
(placa final izquierda y derecha)
Forma D
1 M32 91 2223 10 174 NEV-1DA/DB-ISO
3 M32 91 2226 10 176 NEV-3DA/DB-ISO
4 M32 91 2229 11 140 NEV-4DA/DB-ISO
Placa ciega 1 M32 91 2230 9 489 NDV-1-ISO
3 M32 91 2231 10 340 NDV-3-ISO
4 M32 91 2232 11 142 NDV-4-ISO
Placa ciega 1 M32 91 2233 11 550 NSC-¼-1-ISO
3 M32 91 2234 11 551 NSC-½-3-ISO
4 M32 91 2235 11 699 NSC-¾-4-ISO
Placa intermedia para combinar ta-
maño ISO 1 con
tamaño ISO 3
1 M32 91 2244 12 911 NZV-3-2/1
3 M32 91 2244
– –
Ejemplo de pedido: Conjunto de placas finales, forma D, tamaño 1: 10 174 M32 91 2223
Forma A: placa base individual,
rosca lateral de conexión
Forma C: placa de enlace,
rosca de conexión debajo
conducto lateral de control
Forma D: placa final a placa de
enlace
Forma C
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 35
Accesorios para válvulas según norma de OpelPlacas de enlace según VDMA, tamaño 01 (G¼), tamaño 02 (Gx) con distribución de agujeros según ISO 15407-1
Placas de enlaceISO 15407-1
Denominación Tamaño N° de referencia de Opel Nº de art. Tipo
Placa base individual
Conexiones laterales
01 – 161 109 NAS-¼-01-VDMA
02 – 161 115 NAS-x-02-VDMA
Placa de enlace
para válvulas neumáticas
4
2
12
01 – 161 103 NAW-¼-01-VDMA-VL
02 – 161 111 NAW-x-02-VDMA-VL
Placa de enlace
para electroválvulas
4
2
12
01 – 161 102 NAW-¼-01-VDMA
02 – 161 110 NAW-x-02-VDMA
Placa final 01 – 161 104 NEV-01-VDMA
02 – 161 112 NEV-02-VDMA
Placa intermedia 01/02 – 161 108 NZV-01/02-VDMA
Placa ciega 01 – 161 107 NDV-01-VDMA
02 – 161 114 NDV-02-VDMA
Ejemplo de pedido: placa final, tamaño 01: 161 104 NEV-01-VDMA
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0536
Otros productos según norma de OpelÍndice
Referencia N° de referencia
de Opel
Tipo de Festo Página
Válvulas Valvula de estrangulación y
antirretorno
M32 06 ... GRLA-...-B 37
Válvula de escape rápido M32 08 0026 SE-¼-B 38
Estrangulador del aire de
escape
M32 11 ... GRU-½-B
GRE-...
39
Cierre esférico M22 07 ... QH-... 40
Unidades individuales Manómetro M15 04 ... MA-... 41
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 37
Válvulas de cierre y reguladoras para actuadores según norma Opel, n° de ref. M32 06 ...Válvulas de estrangulación y antirretorno, Gx ... G¾
Válvulas de estrangulación yantirretorno
Festo tipo GRLA
-M- Caudal
0 ... 2000 l/min
-L- Presión de funcionamiento
0,3 ... 10 bar
-Q- Temperatura
–10 ... +60 °C
– Fluido:
aire a presión filtrado,
con o sin lubricación
Las válvulas de estrangulación yantirretono con estrangulación del
aire de escapeson utilizadas para regular el caudal
del aire de escape en cilindros de
doble efecto. En sentido contrario, el
aire pasa por la válvula de antirre-
torno estando completamente abierta
la válvula.
– Conexión roscada Gx hasta G¾
– Montaje directo en el cilindro
– Orientable en 360°
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
151 165 GRLA-x-B M32 06 0081
151 172 GRLA-¼-B M32 06 0095
151 178 GRLA-y-B M32 06 0096
151 179 GRLA-½-B M32 06 0150
151 180 GRLA-¾-B M32 06 0154
Ejemplo de pedido: Válvula de estrangulación y antirretorno con conexión roscada G¼: 151 172 M32 06 0095
Denominación de Opel para una válvula reguladora con rosca de conexión G¼:
Válvula reguladora G¼ M32 06 0095
Informaciones detalladas sobre losproductos véase DVD y
www.festo.com/catalogue/grla
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0538
Válvulas de cierre y reguladoras para actuadores según norma Opel, n° de ref. M32 08 ...Válvulas de escape rápido G¼
Válvula de escape rápidosin silenciador
Festo tipo SE-¼-B
-M- Caudal
300 ... 660 l/min
-L- Presión de funcionamiento
0,5 ... 10 bar
-Q- Temperatura
–20 ... +75 °C
– Fluido:
aire a presión filtrado,
con o sin lubricación
– Descarga común central
Estos elementos permiten aumentar
la velocidad de retroceso del émbolo
en cilindros de simple y doble efecto.
El aire comprimido fluye de la válvula
hacia el cilindro pasando por la vál-
vula de escape rápido. En ese estado,
la salida de aire 3 está cerrada. Si
desciende la presión en 1, entonces
el sentido del aire de escape es de 2
hacia 3.
Para que el escape rápido de aire sea
efectivo, es necesario que la válvula
esté montada directamente sobre la
conexión de aire del cilindro.
El silenciador se encarga de dismi-
nuir el ruido del escape.
Conexión roscada Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
G¼ 9 686 SE-¼-B M32 08 0026
Informaciones detalladas sobre losproductos véase DVD y www.fes-
to.com/catalogue/se
Ejemplo de pedido: Válvula de escape rápido con conexión roscada G¼: 9 686 M32 08 0026
Denominación de Opel para una válvula de escape rápido con rosca de conexión G¼:
Válvula de escape rápido G¼ M32 08 0026
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 39
Válvulas de cierre, reguladoras de caudal y presión según norma Opel, n° de ref. M32 11...Válvulas de estrangulación, Gx ... G½
GRE-... GRU-...-B
Estrangulador el aire de escapeFesto tipo GRU-.../GRE
-M- Caudal
520 ... 8000 l/min
-L- Presión de funcionamiento
máx. 0 ... 10 bar
-Q- Temperatura
–10 ... +70 °C
– Fluido:
aire a presión filtrado,
con o sin lubricación
Estas válvulas se atornillan a las co-
nexiones de escape 3 ó 5 de válvulas
de mando y permiten regular la
velocidad del émbolo de cilindros
mediante estrangulación del aire de
escape.
El tornillo regulador limita la salida
del aire. El escape del aire se produce
a través de un silenciador integrado
reduciéndose el nivel de ruido.
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
9 519 GRU-½-B M32 11 0248
10 351 GRE-x M32 11 0259
10 352 GRE-¼ M32 11 026010 353 GRE-½ M32 11 0261
Ejemplo de pedido: Estrangulador del aire de escape con conexión roscada G¼: 10 352 M32 11 0260 Informaciones detalladas sobre losproductos véase DVD y
www.festo.com/catalogue/greDenominación de Opel para un estrangulador del aire de escape con rosca de conexión G¼:
Estrangulador G¼ M32 11 0260
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0540
Válvulas de cierre, reguladoras de caudal y presión según norma Opel, n° de ref. M22 07 ...Válvulas de cierre Gy ... G1½
Válvula de cierre esféricoFesto tipo QH
-M- Caudal
hasta 84 000 l/min
-L- Presión de funcionamiento
–0,95 ... +30 bar
-Q- Temperatura
–30 ... +200 °C
-R- Vacío
Apropiado para vacío
– Fluido:
aire a presión filtrado,
con o sin lubricación
Estas válvulas permiten cerrar el paso
en ambas direcciones girando la
palanca.
-H- ImportanteEsta válvula no es adecuada para ga-
ses tóxicos, tales como gas natural,
gas ciudad, etc.
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
9 542 QH-y M22 07 0003
9 544 QH-¾ M22 07 0007
9 545 QH-1 M22 07 00086 837 QH-1½ M22 07 0011
Informaciones detalladas sobre losproductos véase DVD y
www.festo.com/catalogue/qh
Ejemplo de pedido: Válvula de cierre esférico con conexión roscada Gy: 9 542 M22 07 0003
Denominación de Opel para una válvula de cierre esférico con rosca de conexión Gy:
Válvula de cierre esférico QH-Gy sin escape M22 07 0003
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 41
Componentes para preparación de aire comprimido según norma Opel, n° de ref. M15 04 ...Equipos de indicación, G¼
ManómetroFesto tipo MA
Forma E, con pivote céntrico detrás,
sin canto de fijación
-Q- Temperatura
–10 ... +60 °C
Para aplicaciones de tipo general
según DIN EN 837-1
– Fluido:
aire a presión filtrado,
con o sin lubricación
– Escala 0 ... 16 bar
– Conexión G¼
Estos manómetros se utilizan para
medir e indicar la presión en siste-
mas de mando.
Están exentos de substancias agresi-
vas para la laca.
Si los manómetros funcionan de
modo permanente (carga en reposo),
únicamente deberán ser sometidos a
una carga equivalente a¾ del valor
máximo de la escala.
Escala
[bar]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
0 ... 2,5 162 845 MA-63-2,5-¼-EN M15 04 0306
0 ... 10 162 840 MA-63-10-¼-EN M15 04 0057
0 ... 16 162 841 MA-63-16-¼-EN M15 04 0079
Ejemplo de pedido: Manómetro, escala desde 0 hasta 16 bar: 162 841 M15 04 0079 Informaciones detalladas sobre losproductos véase DVD y
www.festo.com/catalogue/maDenominación de Opel para un manómetro, forma E, escala desde 0 hasta 16 bar:
Manómetro 1,6E 0 – 16 M15 04 0079
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0542
Cilindros según norma de OpelÍndice
Denominación Tipo de Festo Página
Cilindros multiposiciónCilindros multiposiciónCilindro para accionamiento de
pinzas Euro-C
∅ del émbolo de 70 y 90 mm
D-...-PV2-C-SA 43
Cilindros multiposiciónCilindro para accionamiento de
pinzas Euro-X
Diámetro de émbolo 80 ...
125 mm
DNG-...-30-100-P-SA 45
Cilindros multiposiciónCilindro para accionamiento de
pinzas Euro-X
Diámetro de émbolo 100 ...
125 mm
D-...-60-30-PV2-SA 47
Cilindros de doble efecto
Cilindro de doble efectoUtilización como elevador de pie-
zas para herramientas de pren-
sas
D-35-...-PP-SA 49
Cilindros de doble efectoCilindro de compensación para
pinzas Euro-X
∅ del émbolo de 50 y 63 mm
D-...-20-P-SA 51
Cilindros de doble efectoCilindro de compensación para
pinzas Euro-C
∅ del émbolo de 32 y 40 mm
D-...-35-P-SA 53
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 43
Cilindros según norma de Opel, n° de referencia M13 01...Cilindros de doble efecto,∅ de émbolo de 70 y 90 mm
Cilindros multiposiciónCilindro para accionamiento de pinza
Euro-C
Tipo de Festo D-...-PV2-C-SA
-N- Diámetro
70 y 90 mm
-T- Carrera
Carrera de avance
30 ... 120 mm
Carrera de trabajo
46 mm
-L- Presión máx. de
funcionamiento 12 bar
-Q- Margen de temperatura
–20 ... +80 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
– Cilindro de tres posiciones con ca-
rrera de avance y carrera de trabajo
– Utilización en pinzas para soldar
– Vástago reforzado
– Apoyo reforzado
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0544
Cilindros según norma de Opel, n° de referencia M13 01...Cilindros de doble efecto,∅ de émbolo de 70 y 90 mm
Cilindros multiposiciónD-...-PV2-C-SA
∅
[mm]
Carrera de
avance
[mm]
Carrera de
trabajo
[mm]
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
70 30 46 197639 D-70-30-46-PV2-C-SA M13 01 9760
50 197638 D-70-50-46-PV2-C-SA M13 01 6128
80 197637 D-70-80-46-PV2-C-SA M13 01 5274
100 197636 D-70-100-46-PV2-C-SA M13 01 6129
120 197635 D-70-120-46-PV2-C-SA M13 01 5272
90 30 46 197645 D-90-30-46-PV2-C-SA M13 01 9763
50 197644 D-90-50-46-PV2-C-SA M13 01 6130
80 197643 D-90-80-46-PV2-C-SA M13 01 5277
100 197642 D-90-100-46-PV2-C-SA M13 01 6131
120 197641 D-90-120-46-PV2-C-SA M13 01 5276
Ejemplo de pedido:cilindro multiposición, diámetro del émbolo de 70 mm, carrera de avance 100 mm, carrera de trabajo 46 mm:
197636 D-70-100-46-PV2-C-SA
D-70-... (valores entre paréntesis)
D-90-...
1 Carrera de trabajo en avance
2 Carrera de avance
3 Carrera de retroceso
4 Tornillo para regular la amorti-
guación en las posiciones finales
+ VH = añadir carrera de avance
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 45
Cilindros según norma de Opel, n° de referencia M13 01...Cilindro de doble efecto,∅ de émbolo de 80 ... 125 mm
Cilindros multiposiciónCilindro para accionamiento
de pinza Euro-X
Tipo de Festo DNG-...-30-100-P-SA
Avance, movimiento de retroceso
VV: Avance, movimiento de avance
AV: Carrera de trabajo en avance
AR: Carrera de trabajo en retroceso
-N- Diámetro
80 ... 125 mm
-T- Carrera
Carrera de trabajo
30 mm
Carrera de avance
100 mm
-L- Presión máx. de
funcionamiento 12 bar
-Q- Margen de temperatura
–20 ... +80 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
– Utilización en pinzas para soldar
– Vástagos reforzados
Accesorios:
Posibilidad de suministrar arandelas
limitadoras de la carrera en calidad
de accesorios.
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0546
Cilindros según norma de Opel, n° de referencia M13 01...Cilindro de doble efecto,∅ de émbolo de 80 ... 125 mm
Cilindros multiposiciónDNG-...-30-100-P-SA
∅
[mm]
Carrera de
avance
[mm]
Carrera de
trabajo
[mm]
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
80 100 30 155776 DNG-80-30/100-P-SA M13 01 6132
100 100 30 173185 DNG-100-30/100-P-SA M13 01 6133
125 100 30 155678 DNG-125-30-100-P-SA –
Ejemplo de pedido:cilindro multiposición, diámetro del émbolo de 125 mm, carrera de avance 100 mm, carrera de trabajo 30 mm:
155678 DNG-125-30-100-P-SA
1 Conexión para carrera de trabajo en avance
2 Conexión para carrera de trabajo en retroceso
3 Carrera de avance, conexión para movimiento de avance
4 Carrera de avance, conexión para movimiento de retroceso
∅
[mm]
AF B
∅
E E1 EE J1 KF
80 32 55 100 100 G¼ 30 M20x1,5
100 32 55 126 124 G¼ 30 M20x1,5
125 32 55 140 140 G¼ 40 M20x1,5
∅
[mm]
L2 MM
h8
PL PL1 TG VD WH ZJ ZM+ ß 1 ß 2
80 90 32 10 10 72 20 33 263 296 27 7
100 89 32 9 9 89 20 33 263 296 27 7
125 128 32 17 12 110 8 22 324 346 27 9
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 47
Cilindros según norma de Opel, n° de referencia M13 01...Cilindro de doble efecto,∅ de émbolo de 100 ... 125 mm
Cilindros multiposiciónCilindro para accionamiento
de pinza Euro-X
Tipo de Festo D-...-60-30-PV2-SA
-N- Diámetro
100 ... 125 mm
-T- Carrera
Carrera de avance
60 mm
Carrera de trabajo
30 mm
-L- Presión máx. de
funcionamiento 12 bar
-Q- Margen de temperatura
–20 ... +80 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
– Cilindro de tres posiciones con ca-
rrera de avance y carrera de trabajo
– Utilización en pinzas para soldar
– Vástago reforzado
– Amortiguación ajustable en las po-
siciones finales dentro de la ca-
rrera de trabajo
Accesorios:
Posibilidad de suministrar arandelas
limitadoras de la carrera en calidad
de accesorios.
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0548
Cilindros según norma de Opel, n° de referencia M13 01...Cilindro de doble efecto,∅ de émbolo de 100 ... 125 mm
Cilindros multiposiciónD-...-60-30-PV2-SA
∅
[mm]
Carrera de
avance
[mm]
Carrera de
trabajo
[mm]
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
100 60 30 192867 D-100-60-30-PV2-SA M13 01 9820
125 60 30 194495 D-125-60-30-PV2-SA M13 01 9827
Ejemplo de pedido:cilindro multiposición, diámetro del émbolo de 125 mm, carrera de avance 60 mm, carrera de trabajo 30 mm:
194495 D-125-60-30-PV2-SA
1 Amortiguación regulable en las
posiciones finales
RH = Carrera de retroceso
AH = Carrera de trabajo
VH = Avance
∅
[mm]
BG D4
∅
D5
∅
E J1 J2 J3 J4 MM
∅
h8
PL ß1
100 50 107 10 120 30 18 21 30 32 25 27
125 42 133 12 133 37 28 25 40 40 23 36
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 49
Cilindros según norma de Opel, n° de referencia M13 01...Cilindros de doble efecto,∅ diámetro de émbolo de 35 mm
Cilindro de doble efectoUtilización como elevador de piezas
para herramientas de prensas
Festo tipo D-35-...-PP-SA
-N- Diámetro
35 mm
-T- Carrera
60, 75 y 90 mm
-L- Presión de funcionamiento
0,5 ... 10 bar
-Q- Temperatura
–20 ... +80 °C
– Fluido:
Aire comprimido lubricado o sin
lubricar
– Amortiguación en ambos finales de
carrera mediante estrangulador fijo
– Camisa del cilindro con niquelado
duro
– Conexiones para el aire en el
vástago
Carrera
[mm]
∅
[mm]
Referencia de Festo
Nº de art. Tipo
N° de referencia de Opel
60 35 38 550 D-35-60-PP-SA M13 01 3578
75 35 194 038 D-35-75-PP-SA M13 01 8794
90 35 38 551 D-35-90-PP-SA M13 01 3579
Ejemplo de pedido: cilindro de doble efecto,∅ de émbolo de 35 mm, carrera de 60 mm: 38 550 D-35-60-PP-SA
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0550
Cilindros según norma de Opel, n° de referencia M13 01...Cilindros de doble efecto,∅ diámetro de émbolo de 35 mm
Cilindro de doble efectoD-35-...-PP-SA
1 Avance
2 Retroceso
3 orientable en 360°
+ = añadir carrera
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 51
Cilindros según norma de Opel, n° de referencia M13 01...Cilindros de doble efecto, diámetro del émbolo de 50 y 63 mm
Cilindro de doble efectoCilindro de compensación
para pinza Euro-X
Tipo de Festo D-…-20-P-SA
-N- Diámetro
50 mm y 63 mm
-T- Carrera
20 mm
-L- Presión de funcionamiento
0,5 ... 12 bar
-Q- Margen de temperatura
–20 ... +80 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
– Utilización en pinzas para soldar
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0552
Cilindros según norma de Opel, n° de referencia M13 01...Cilindros de doble efecto, diámetro del émbolo de 50 y 63 mm
Cilindro de doble efectoD-...-20-P-SA
∅
[mm]
Carrera
[mm]
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
50 20 184809 D-50-20-P-SA M13 01 5644
63 20 526604 D-63-20-P-SA M13 01 5645
Ejemplo de pedido:cilindro de doble efecto, diámetro del émbolo de 50 mm, carrera de 20 mm
184809 D-50-20-P-SA
∅
[mm]
B1 B2 D1
∅
D2 D3
H7
∅
D4 EE H1 H2
∅
h8
H3
+0,1
H4 L1 L2
50 67,6 ~32,4 20 M10 10 M4 G1/4 67,6 58 15 2,9 80,5 50,5
63 86,6 ~36,1 86,6 3,9 82,5 52,5
∅
[mm]
L3
+0,1
L4
+0,3
L5 L6 L7 L8 L9 T1 T2 W1 ß1
50 68,5 10 42 18 13,5 8 6 15 8 60° 17
63 70,5 10 44
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 53
Cilindros según norma de Opel, n° de referencia M13 01...Cilindros de doble efecto, diámetro del émbolo de 32 y 40 mm
Cilindro de doble efectoCilindro de compensación
para pinza Euro-C
Tipo de Festo D-…-35-P-SA
-N- Diámetro
32 mm y 40 mm
-T- Carrera
35 mm
-L-Presión de funcionamientomáx.
12 bar
-Q- Margen de temperatura
–20 ... +80 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
– Utilización en pinzas para soldar
– Casquillos aislantes embutidos en
el lado de la conexión
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0554
Cilindros según norma de Opel, n° de referencia M13 01...Cilindros de doble efecto, diámetro del émbolo de 32 y 40 mm
Cilindro de doble efectoD-...-35-P-SA
∅
[mm]
Carrera
[mm]
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
32 35 183529 D-32-35-P-SA M13 01 5646
40 35 549219 D-40-35-P-SA M13 01 5647
Ejemplo de pedido:cilindro de doble efecto, diámetro del émbolo de 32 mm, carrera de 35 mm
183529 D-32-35-P-SA
1 Casquillo aislante POM
∅
[mm]
B1 B2 B3 B4 D1
∅
D2
∅
D3 D4
∅
D5
∅
EE H1 H2
32 70 52 42 18 28 12 M8 8,2 11,5 G1/8 45 34,6
40 30 8,3
∅
[mm]
H3 H4 L1 L2 L3 L4 L5 L6 L7 T1 ß1 ß2
32 22,5 8 75 57 32 10 14 8 17 10 24 10
40 59 —
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 55
Unidades de control según norma de OpelÍndice
Denominación Tipo de Festo Página
Placa reguladoraPlaca reguladora
Para cilindro de compensación,
doble
RP VSPA 56
Placa reguladora
Para cilindro de compensación,
cuádruple
RP VSPA-VSVA 58
Bloque de válvulasBloque de válvulas
Para pinza Euro C-45/C45HD
Bloque de mando ISO15407 60
Bloque de válvulas
Para pinza Euro X50/450
Pinza X-1000
Bloque de mando ISO5599 62
Bloque de válvulas
Para pinza UE X50/550
Bloque de mando ISO5599 64
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0556
Placas reguladoras según norma de OpelPlaca reguladora para cilindro de compensación, doble
Placa reguladoraPara cilindro de compensación, doble
Tipo Festo, placa reguladora RP VSPA
-L- Presión de alimentación
(P1)
máx. 12 bar
Márgenes de regulación
1 ... 12 bar
Conexión 14
2 ... 12 bar
-Q- Margen de temperatura
–10 ... +60 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
– Para cilindros de compensación
– 2 válvulas
– Utilización estacionaria
La placa reguladora viene montada y
lista para la conexión y consta de:
– 1 válvula neumática
– 2 reguladores
– 2 manómetros con indicación del
valor nominal
– 1 silenciador
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 57
Placas reguladoras según norma de OpelPlaca reguladora para cilindro de compensación, doble
Placa reguladoraRP VSPA
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
1389050 RP VSPA M32 03 1442
Ejemplo de pedido:Placa de regulación
1389050 RP VSPA
B1 H1 H2 L1 L2 L3
~84 ~95,1 10 87 66 10,5es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0558
Placas reguladoras según norma de OpelPlaca reguladora para cilindro de compensación, cuádruple
Placa reguladoraPara cilindro de compensación, cuá-
druple
Tipo Festo, placa reguladoraRP VSPA-VSVA
-L- Presión de alimentación
(P2)
máx. 12 bar
Márgenes de regulación
1 ... 12 bar
Conexión 14
2 ... 12 bar
-Q- Margen de temperatura
–10 ... +60 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
– Para cilindros de compensación
– 4 válvulas
– Utilización en robots
La placa reguladora viene montada y
lista para la conexión y consta de:
– 2 válvulas neumáticas
– 2 electroválvulas
– 4 reguladores
– 4 manómetros con indicación del
valor nominal
– 1 silenciador
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 59
Placas reguladoras según norma de OpelPlaca reguladora para cilindro de compensación, cuádruple
Placa reguladoraRP VSPA-VSVA
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
1375452 RP VSPA-VSVA M32 03 1504
Ejemplo de pedido:Placa de regulación
1375452 RP VSPA-VSVA
B1 B2 B3 H1 L1 L2 L3
~159,1 78 5,7 ~117,8 ~141,6 110 5
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0560
Bloques de mando según norma de OpelBloque de mando para pinza Euro C-45 / C45HD
Bloque de válvulasPara pinza Euro C-45 / C45HD
Tipo de Festo, bloque de mandoISO15407
-L- Presión de alimentación
(E1)
máx. 8 bar
-Q- Margen de temperatura
5 ... 50 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
El bloque de mando viene montado y
listo para la conexión y consta de:
– 1 Bloque de válvulas
– 3 electroválvulas
– 2 silenciador
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 61
Bloques de mando según norma de OpelBloque de mando para pinza Euro C-45 / C45HD
Bloque de válvulasBloque de mando ISO15407
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
1388296 Bloque de mando ISO15407 M32 09 1599
Ejemplo de pedido:Bloque de mando
1388296 Bloque de mando ISO15407
B1 B2 B3 B4 H1 H2 L1 L2 L3 L4 L5
~128 71,5 44,5 17,5 ~98,8 26 ~122,5 69 48 27 6
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0562
Bloques de mando según norma de OpelBloque de mando para pinza Euro X50/450 y pinza X-1000
Bloque de válvulasPara pinza Euro X50/450
X-1000 Pinza
Tipo de Festo, bloque de mandoISO5599
-L- Presión de alimentación
(E1)
máx. 10 bar
-Q- Margen de temperatura
5 ... 50 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
El bloque de mando viene montado y
listo para la conexión y consta de:
– 1 Bloque de válvulas
– 3 electroválvulas
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 63
Bloques de mando según norma de OpelBloque de mando para pinza Euro X50/450 y pinza X-1000
Bloque de válvulasBloque de mando ISO5599
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
1388209 Bloque de mando ISO5599 M32 09 1293
Ejemplo de pedido:Bloque de mando
1388209 Bloque de mando ISO5599
B1 H1 H2 L1 L2 L3 L4
~152 ~92,3 22 ~138,1 26,5 26,5 13,5
es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0564
Bloques de mando según norma de OpelBloque de mando para pinza Euro x50/550
Bloque de válvulasPara pinza UE X50/550
Tipo de Festo, bloque de mandoISO5599
-L- Presión de alimentación
(E1)
máx. 10 bar
-Q- Margen de temperatura
5 ... 50 °C
– Fluido:
aire comprimido lubricado o sin lu-
bricar
El bloque de mando viene montado y
listo para la conexión y consta de:
– 1 Bloque de válvulas
– 2 electroválvulas
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 65
Bloques de mando según norma de OpelBloque de mando para pinza Euro x50/550
Bloque de válvulasBloque de mando ISO5599
Referencia de Festo
Nº de artículo
Tipo
N° de referencia de Opel
1388476 Bloque de mando ISO5599 M32 09 1294
Ejemplo de pedido:Bloque de mando
1388476 Bloque de mando ISO5599
B1 H1 H2 L1 L2 L3 L4
~109 ~92,3 22 ~138,1 26,5 26,5 13,5es
Festo AG & Co. KG – Programa sector automóvil – Reservado el derecho de modificación - 2012/0566
Software de ingeniería
Desde la primera definición del con-
cepto de las instalaciones se deter-
mina el uso eficiente de energía y la
pronta recuperación de las inversio-
nes. Durante la fase de ingeniería
puede reducirse el posterior consumo
de energía, recurriendo a programas
de software altamente eficientes para
seleccionar los componentes apropia-
dos de dimensiones correctas. Lo di-
cho se aplica tanto a sistemas de ac-
cionamiento eléctrico como neumá-
tico. Con los programas de software de
ingeniería de Festo, se evitan compo-
nentes y sistemas de dimensiones in-
necesariamente grandes. Al mismo
tiempo, el software se encarga de
adaptar los componentes y sistemas
de manera óptima a las aplicaciones
específicas del cliente. Cualquiera que
sea la exigencia, Festo ofrece la solu-
ción ideal para cada aplicación.
Actuadores de posicionamiento ¿Qué actuador lineal electromecánico
es el más apropiado para solucionar
una tarea determinada? Usted no
tiene más que introducir los datos de
su aplicación (posiciones, masa útil,
posición de montaje), y el software
propone la solución ideal.
Dimensionamiento neumático conProPneu
Simulaciones perfectas en vez de cos-
tosas pruebas. Con ProPneu es fácil
seleccionar y configurar la cadena
completa de control neumático. Si
cambia un parámetro, el software se
encarga de adaptar automáticamente
todos los demás.
Cálculo de vacío ¿Qué ventosa es apropiada para qué
superficies y qué tipo de movimien-
tos? ¡Prescindir de ensayos innecesa-
rios mediante cálculos precisos! Con
este software, es posible diferenciar
entre movimientos lineales y girato-
rios.
Selección de tubos flexibles Basta introducir los parámetros nece-
sarios (por ejemplo, presión de fun-
cionamiento, exposición a substan-
cias químicas, resistencia contra de-
tergentes), y el programa selecciona el
tubo flexible apropiado para la apli-
cación.
Consumo de aire Determine el consumo de aire de sus
instalaciones de manera rápida y sen-
cilla. Consideración de todos los actu-
adores y tubos flexibles, de la dura-
ción de los ciclos y de la presión de
funcionamiento, para calcular el con-
sumo de aire por minuto y por día. Ex-
portación de las tablas de datos y de
los resultados a hojas de cálculo Ex-
cel.
es
2012/05– Reservado el derecho de modificación – Programa sector automóvil – Festo AG & Co. KG 67
Software de ingeniería
Selección de pinzas La sujeción fiable de las piezas de-
pende del cálculo correcto. En este
caso, cálculo considerando peso, sen-
tido del movimiento, distancias, etc.:
el software determina qué pinza para-
lela, radial, angular o de tres dedos es
la más apropiada para solucionar una
tarea determinada.
Elección de amortiguadores Trátese de movimientos oblicuos, ver-
ticales, en curva o rectos, mediante
palanca o disco, se tienen en cuenta
todos los movimientos amortiguados.
El software siempre propone el amor-
tiguador más apropiado.
Momento de inercia de la masa Ya no son necesarios bolígrafos y cal-
culadoras manuales. Trátese de dis-
cos, dados, bridas, pinzas, etc., este
software calcula los momentos de
inercia de la masa de cualquier pieza.
Guardar, aplicar o imprimir y ¡listo!
Soft Stop Con el Soft Stop, casi todo es posible.
Reducción del 30% del tiempo nece-
sario para la ejecución de los movi-
mientos de actuadores neumáticos y
disminución drástica de las vibracio-
nes. El programa de selección se en-
carga de realizar todos los cálculos
necesarios.
Cálculo de guías para actuadoreslineales neumáticos
Los actuadores lineales de Festo tie-
nen fama por aplicar mucha fuerza en
mínimo espacio. El software deter-
mina la configuración óptima. Usted
no tiene más que introducir los pará-
metros del proyecto, tales como masa
o fuerza, posición de montaje y reco-
rrido.
es