Post on 15-Feb-2020
www.powdernotes.comDevelopment of Novel Compaction Regimes for
Hydrogen Storage MaterialsPI: Bryan Ennis
Presenter: Brandon EnnisOther team members: Michael Winn, Naseem Jibrin,
Benjamin Ennis
E&G Associates, Inc.13 June 2018 Project ID #st151
This presentation does not contain any proprietary, confidential, or otherwise restricted information
www.powdernotes.com
2
• Barriers addressed:• A. System Weight and Volume• D. Durability/Operability
Timeline• Project Start Date: 04/09/2018• Project End Date: 10/08/2018
Budget• Total Project Budget: $149,751
Timeline and Budget Barriers
• No partners currentlyPartners
Overview
www.powdernotes.com
3
AbstractFuel Cell Electric Vehicles (FCEV) are an emerging technology for improving energy
efficiency and reducing pollution emissions related to transportation. However, improving on-board Hydrogen storage is a key challenge to the advancement of light duty FCEV. Current storage methods utilize composite on-board vessels for high pressure Hydrogen gas. This method is costly and requires large storage volumes which is problematic for light duty vehicles.
Alternative methods of storage using materials that either chemically bind and release hydrogen, or reversibly adsorb hydrogen, have long been investigated as a means to lower the onboard storage pressure, reduce overall system and delivery costs, and lessen safety concerns. However, these materials struggle to meet the system targets for volumetric density due to packing inefficiencies of the storage materials.
This shortfall of hydrogen sorption storage systems can be overcome by densification of absorbent material while maintaining available surface area.
In Phase I, suitable sorbent materials will be chosen for evaluation, and tested for initial material properties and performance characteristics. Based on material properties, material will be densified via compaction processes optimized to the specific material. Materials will be tested for performance properties after densification to quantify improvements in overall performance. Following evaluation of material performance, process refinement will be addressed.
www.powdernotes.com
4
• Objective: To establish novel material densification regimes for sorbent materials utilized in hydrogen storage systems (w/high volume storage of small footprint), and required solids processing methods based on incoming material properties of sorbent powder feeds, using industry standard design principles of single and/or dual stage granulation & compaction processes.
• Anticipated Impact DOE TechnicalSystem Targets:• System Volumetric Capacity
– Increase H2 volumetric uptake• Durability/Operability
– Increase mechanical strength of sorbent form
Relevance
www.powdernotes.com
5
1. Establish likely solids processes:• Fabricate high-density powder compacts or granulate• Maintain accessible surface area/pore space to meet volumetric DOE targets• Review multi-step processes (e.g. wet/dry granulation plus tableting)
2. Assess bulk material properties of MOF and carbon powders:• Wetting behavior & related stability• Powder and die/roll/wall friction vs. pressure• Powder cohesion, bulk permeability, bulk density vs. pressure
3. Evaluate typical, likely process methods:• Wet solvent-based granulation methods that maintain sorbent stability• Roll pressing as a dry granulate production method• Tableting as a dry compaction method (both powder or granulate feeds)• Evaluate accessible surface area and mechanical integrity
4. Preliminary formulation design:• Assess the addition of select, non-sorbent materials (excipients, lubricants) • To improve process operability and product uniformity and strength• Increase volumetric capacity at reduced footprint
5. Develop a commercialization plan:• Down select representative sorbent formulations & process methods, w/ costing• Identify sorbent and processing partners & collaborators• Establish Phase Two plan
Approach: Key Objectives (1)
www.powdernotes.com
6
Approach: Key Objectives (2)
Example multistep densification process for H2 sorbent materials, w/ feed powder, granulate and compact characterization.
Specific Phase I Activities:1. Selection of porous carbon and MOF sorbent feed powders. 2. Construction of In-House Sievert 3. Material Property Characterization of Sorbent Feed Powders. 4. Initial Densification Trials by Granulation and Compaction. 5. Material Property Characterization of Densified Material. 6. Down-Selection of Sorbent Materials for Additional Densification Studies. 7. Performance metrics.
www.powdernotes.com
7
Overview of granulation & compaction:• To significantly increase bulk density of a feed powder• With controlled porosity and mechanical strength• In a free flowing, non-segregating defined meterable structural form• While maintaining key powder attributes (e.g. accessible surface area)• Employing industry standards of engineering process-formulation design• Using often wet granulation, dry granulation, and tableting processes• PI team has 30 decades of experience in granulation/compaction design
Approach: Overview
Example processes. (left) Low-shear granulation processes include both batch and continuous choices, such as the batch and continuous fluid-beds, and continuous rotating discs and drums. (right) . Examples of compressive agglomeration include: For dry compaction, (a) tableting, (b) roll pressing, (c) briquetting, (d) ram extrusion; and for paste extrusion, (e) screw extrusion and (f) concentric-roll pelletizing. From Ennis.9
www.powdernotes.com
8
• What is wet granulation?– Controlling granule size and internal porosity
• Rate process steps in wet granulation:– wetting, growth, consolidation, attrition
• Material properties:– wettability, wet mass rheology, permeability, fracture toughness
Approach: What is Wet Granulation?
www.powdernotes.com
9
Approach: Wet Granulation
Define desired properties of final granule product
Material characterization of feed powder properties
Design formulation to achieve desired granule properties
Select granulation processbased on formulation and desired granule properties
Select operating variablesbased on formulation, process, and desired granule properties
Size distribution, wettability, permeability, powder flowability, powder friction, wall friction
Surfactants, wetting & dispersants, diluents, binders & lubricants, solvents
Tumbling granulators, mixer granulators, fluid-bed granulators
Size distribution, wettability, permeability, powder flowability, powder friction, wall friction
www.powdernotes.com
10
Approach: What is Compaction?• What is dry granulation and compaction?
– Controlling compact strength and uniformity of internal porosity• Mechanical steps in dry granulation & compaction:
– Zone filling, stress transmission, plastic deformation, bonding,deareation, elastic recovery & flaw/damage
• Material properties:– Powder/wall friction, hardness, brittle v. plastic, interfacial energy,
permeability vs. load, elastic modulus
www.powdernotes.com
11
Approach: Processes compared• Density map of granulation/compaction processes
www.powdernotes.com
12
Approach: Processes compared• Process selection considerations of
granulation/compaction processes
www.powdernotes.com
13
Approach: Challenges in compaction• Poor stress transmission and density maldistribution• Rate limiting deareation (related to low powder permeability, fine powder)• Leads to unnecessary losses in surface area• Corrected by lubricants, compact geometry, dwell profile, vacuum feeds
Tablet density profiles by chemical imaging. Comparison of tablet absorbance or density profiles for lactose tablets. Representative images of tablet tops, bottoms, and edges are shown for 0%, 0.25%, and 1.0% MgS blended 30 s or 30 min. Higher absorbance correlates to higher density.
www.powdernotes.com
14
Approach: Challenges in compaction
Tablet density profiles & ejection forces. Tablet density profiles (top to bottom), stress transmission ratios (force ratio) and ejection force for varying MgS lubricant for lactose formulations. Higher absorbance correlates to higher density.
www.powdernotes.com
15
• Acquisition of MOF-5 and porous carbon samples
• Preparation of equipment for granulation & compaction trials:– Fluid-bed granulator– Tumble granulator– Laboratory roll press– MCC Presster™ Tablet Press Simulator
• Preparation of material characterization equipment– Sympatec HELOS for particle size distribution– Micromeritics Tristar for BET surface area & porosity– Micromeritics Accupyc™ for skeletal density– Rame-Hart goniometer for contact angle & wettability– iShear™ Rotary Shear Cell for powder flowability and friction– iFluid™ Permeability Cell for gas permeability and fluidization behavior
Accomplishments and Progress
This project was not reviewed last year.
Responses to Previous Year Reviewers’ Comments
www.powdernotes.com
16
Collaboration & Coordination
• E&G is working to initiate collaborations:– NREL for high pressure sorption capacity measurement of granules
and compacts produced from this project.– Univ. of TN for uniaxial compression characterization and high
pressure friction to complement E&G Prester tablet press replicator
www.powdernotes.com
Remaining Challenges and Barriers
• Densification of sorbent materials offers severalchallenges, of which some of the requirements are:o Maintaining high active pore volume and high accessible surface
area of adsorption, as well as uniformity of these properties, asclose as possible to the original raw powder.
o Achieving sufficient mechanical strength (and related propertiessuch as flex strength) of the form for handling and final end-use,including during repeated, long term operational cycling.
o Avoiding thermal or chemical degradation of the MOF powderduring production.
17
www.powdernotes.com
18
• Acquisition of porous carbon and MOF sorbent feed powders.
• Material property characterization of sorbent feed powders.
• Initial densification trials by granulation and compaction.
• Material property characterization of densified material.
• Down-selection of sorbent materials for additional densification studies.
• Evaluate final material properties against performance metrics.
• Propose Phase II work based on results of Phase I work.
Proposed Future Work
Any proposed future work is subject to change based on funding levels
www.powdernotes.com
19
• For select sorbent materials, characterize particle scaleand bulk powder scale properties relevant to granulationand compaction processes.
• Identify granulation formulations and processes that willincrease volumetric sorption capacity.
• Conduct granulation trials with sorbent materials• Conduct compaction trials with granulated sorbent and
raw feed powder.• Characterize hydrogen storage capacity of granules and
compacts.
Summary
Development of Novel Compaction Regimes for Hydrogen Storage MaterialsSlide Number 2AbstractSlide Number 4Slide Number 5Slide Number 6Slide Number 7Slide Number 8Slide Number 9Slide Number 10Slide Number 11Slide Number 12Slide Number 13Slide Number 14Responses to Previous Year Reviewers’ CommentsCollaboration & CoordinationRemaining Challenges and BarriersSlide Number 18Slide Number 19