Post on 12-Mar-2016
description
145
SWITCHES ROUND PADDLE LEVER TOGGLE
Current Rating: 3A 250VAC, 6A 125VAC Initial Contact Resistance: <50Meg Ohms @12VDCInsulation Resistance: >100Meg OhmsDielectric Strength (Open Contacts): >1500V for 1 minuteContact Material: Silver Plated BrassTerminal Material: Copper AlloyBody Material: Nylon (UL 94V-2)Actuator & Bezel: Nylon (UL 94V-2)Terminal Type: Solder ConnectionMounting hardware: M15 P1.0
Part No. Type Action Actuator Color
30-10320 SPST On-Off Black Paddle30-10322 SPDT On-On Black Paddle30-10324 SPDT On-(On) Black Paddle30-10326 SPDT On-Off-On Black Paddle30-10328 SPDT On-Off-(On) Black Paddle30-10329 SPDT (On)-Off-(On) Black Paddle
ROUND PADDLE LEVER TOGGLE SWITCHES
Panel Cut-out: 15mm (.59”)Maximum panel thickness 6.0 mm
Current Rating: 6A 250VAC, 10A 125VAC Initial Contact Resistance: <50Meg Ohms @12VDCInsulation Resistance: >100Meg OhmsDielectric Strength (Open Contacts): >1500V for 1 minuteContact Material: Silver Plated BrassTerminal Material: Copper AlloyBody Material: Nylon (UL 94V-2)Actuator & Bezel: Nylon (UL 94V-2)Terminal Type: Solder ConnectionMounting Hardware: M18 P1.0Lamp Voltage: LED 2V* @20ma (*resistor needed for other voltages)
Part No. Type Action Lamp / Actuator Color
30-10440 DPST On-Off Black Paddle30-10442 DPDT On-On Black Paddle30-10444 DPDT On-Off-On Black Paddle30-10522 SPST On-Off LED Lamp, Red30-10523 SPST On-Off LED Lamp, Amber30-10525 SPST On-Off LED Lamp, Green30-10622 SPDT On-On LED Lamp, Red30-10623 SPDT On-On LED Lamp, Amber30-10625 SPDT On-On LED Lamp, Green30-10722 SPDT On-Off-On LED Lamp, Red30-10723 SPDT On-Off-On LED Lamp, Amber30-10725 SPDT On-Off-On LED Lamp, Green
ROUND PADDLE LEVER TOGGLE SWITCHES
Panel Cut-out: 18mm (.70”)Maximum panel thickness 5.0 mm
LED indicator on top oflever
( ) = Momentary
Using an LED
An LED (light emitting diode) requires about two volts to operate and twenty milliamps of current. A currentlimiting resistor must be used in series with an LED to prevent current over 20 mA from flowing; otherwise,your LED will be damaged. You may simply use Ohm’s law to calculate the resistor value. Here is an exam-ple, we have a circuit operating at 12 volts DC, and need to know the value of a resistor to use. The LED“wants” two volts to operate ; so subtract 2 from the 12 volts which is of course, ten. Plug the “ten” in at “E”and divide by “I” or .020 amps. The result is 500 ohms for the resistor value
If you forget to subtract the two volts, the resistor value will be 600 and the LED will not be at maximumbrightness. However, it will last much longer! (about double normal life).
Another formula you can use is R=50(V-2). The R is for resistor, the V for voltage. We like this one as it iseasy to recall and do in your head.
LED wth DC (Direct Current)
When using an LED with AC, a diode must be placed inseries with the LED. Because AC will only be flowing1/2 the time, we use a variation on the easy formulashown to the left(bottom). Use R=25(V2.7), whichincludes the voltage drop across the diode.
So, if you have a circuit using 28 volts AC, multiply25.3 (or 28V -2.7), times 25 equals 632 ohms. We needto use a standard value resistor, so use 680 ohms for“R”.
LED wth AC (Alternating Current)
DC Volts 5V 6V 12V 24VResistor (ohms) 150 180 470 1200
AC Volts 6V 12V 24V 48V 117VResistor (ohms) 82 220 560 1200 3K
Typical voltages used in electronics and resistor values (rounded to nearest standard resistor).
146
SWITCHES STANDARD TOGGLE
STANDARD SIZE BAT HANDLE TOGGLE SWITCH
STANDARD SIZE BAT HANDLE TOGGLE SWITCHES
C
STANDARD SIZE BAT HANDLE TOGGLE SWITCHES
HEAVY DUTY TOGGLE SWITCHES, AC/DC MOTOR CONTROL
Mounting Hole: 0.500”
Current Rating: 15A @ 125V AC, 10A @ 277V ACInitial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Silver PlateTerminal Material: Brass Terminal Type: Screw
SPECIFICATIONS:
Part No.30-067
30-10360*
ActuatorMetalMetal
TypeSPSTDPST
ActionONON
--
OFFOFF
Current Rating: 20A @125V AC, 10A @ 277V AC3/4 HP @ 125/277V AC
*1-1/2 HP @ 125/277V ACInitial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Nickel PlateTerminal Material: Brass Terminal Type: Screw
SPECIFICATIONS:
Part No.30-020*30-022
ActuatorMetalMetal
TypeSPSTSPDT
ActionONON
--
OFFON
* = 3/4 HP 125-250VAC
Current Rating: 6A @ 125V AC, 3A @ 277V ACInitial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Nickel PlateTerminal Material: BrassTerminal Type: .250” Quick Connect
SPECIFICATIONS:
Part No.30-019
ActuatorMetal
TypeDPST
Action
Current Rating: 16A @125V AC, 8A @ 250V AC1 HP @ 125-250V AC
Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V 1 minuteBase Material: PhenolicBezel Material: Brass/Nickel PlateTerminal Type: .Screw (#6-32NC-2 Thread)
SPECIFICATIONS:
Part No.30-1034130-10131
30-10342*
ActuatorBrass Nickel PlateBrass Nickel PlateBrass Nickel Plate
TypeSPSTDPSTDPST
ActionONONON
---
OFFOFFOFF
* = Rating for 30-10342 is 20A @ 125VAC, 10A @ 250VAC, 1-1/2 HP 125-250VAC
ON OFF
C
-
147
Current Rating: 20A @125V AC, 10A @ 277V AC3/4 HP @ 125-250V AC
Initial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Bright Nickel PlateTerminal Material: BrassTerminal Type: .250” Quick Connect
SPECIFICATIONS:
Part No.30-30030-30530-31030-31530-335
ActuatorMetalMetalMetalMetalMetal
TypeSPSTSPSTSPDTSPDTSPDT
Action
SWITCHES STANDARD TOGGLE
HEAVY DUTY BAT HANDLE TOGGLE SWITCHES - SPST & SPDT
HEAVY DUTY BAT HANDLE TOGGLE SWITCHES -SPST & SPDT
Current Rating: 20A @125V AC, 10A @ 277V AC3/4 HP @ 125/250V AC
Initial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Bright Nickel PlateTerminal Material: BrassTerminal Type: Screw
SPECIFICATIONS:
Part No.30-08030-35530-01330-11630-01030-05330-055
ActuatorMetalMetalMetalMetalMetalMetalMetal
TypeSPSTSPSTSPDTSPDTSPDTSPDTSPDT
Action
NOTE: ( ) = Momentary
ON(ON)ONONONON
(ON)
----
OFFOFFOFF
OFFOFFON
(ON)ON
(ON)(ON)
Terminal
HEAVY DUTY BAT HANDLE TOGGLE SWITCHES -SPST & SPDT
Current Rating: 20A @ 125V AC, 10A @ 277V AC3/4 HP @ 125-250V AC
Initial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Bright Nickel PlateTerminal Material: Brass - Tin DippedTerminal Type: Solder
SPECIFICATIONS:
Part No.30-07830-07630-01430-01630-086
ActuatorMetalMetalMetalMetalMetal
TypeSPSTSPSTSPDTSPDTSPDT
Action
NOTE: ( ) = Momentary
ON(ON)ONONON
----
OFF
OFFOFFON
(ON)(ON)
HEAVY DUTY UTILITY BAT HANDLE TOGGLE SWITCH
(Two Circuit)
Mounting Hole: 0.500”
Current Rating: 20A @125V AC, 10A @ 250V AC1-1/2 HP @ 125-250V AC
Initial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Nickel PlateTerminal Material: BrassTerminal Type: Screw
SPECIFICATIONS:
Part No.30-135
ActuatorMetal
TypeSP3T
ActionON ON ON ON (2+6)
ON (2+4)ON (1+4)
C
C
C
(ON)ONONON
(ON)
---
OFFOFF
OFFOFFONON
(ON)
NOTE: ( ) = Momentary
148
SWITCHES STANDARD TOGGLE
HEAVY DUTY BAT HANDLE TOGGLE SWITCHES -DPST & DPDT
HEAVY DUTY BAT HANDLE TOGGLE SWITCHES -DPST & DPDT
Mounting Hole: 0.500”
Terminal
Mounting Hole: 0.500”
Terminal
HEAVY DUTY BAT HANDLE TOGGLE SWITCHES - 3PST &3PDT
HEAVY DUTY BAT HANDLE TOGGLE SWITCHES -DPST & DPDT
Current Rating: 20A @125V AC, 10A @ 277V AC1-1/2 HP @ 125-250V AC
Initial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Bright Nickel PlateTerminal Material: BrassTerminal Type: .250” Quick Connect
SPECIFICATIONS:
Part No.30-34530-32030-32530-330
ActuatorMetalMetalMetal
TypeDPSTDPDTDPDTDPDT
ActionONONON
(ON)
--
OFFOFF
OFFONON
(ON)
Mounting Hole: 0.500”
Terminal
Current Rating: 20A @125V AC, 10A @ 277V AC1-1/2 HP @ 125-250V AC
Initial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Bright Nickel PlateTerminal Material: BrassTerminal Type: Screw
SPECIFICATIONS:
Part No.30-31230-36530-04630-04830-05130-050
ActuatorMetalMetalMetalMetalMetalMetal
TypeDPSTDPSTDPDTDPDTDPDTDPDT
ActionONONONONON
(ON)
---
OFFOFFOFF
OFF(OFF)
ONON
(ON)(ON)
Current Rating: 20A @125V AC, 10A @ 277V AC1-1/2 HP @ 125/250V AC
Initial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500V DCDielectric Strength: 1000V AC 50/60 Hz for 1 minuteContact Material: Brass - Bright Nickel PlateTerminal Material: BrassActuator Type: Solder - Tin Dipped
SPECIFICATIONS:
Part No.30-01230-05230-049
ActuatorMetalMetalMetal
TypeDPSTDPDTDPDT
Action
NOTE: 5 6 7 Momentary
NOTE: 5 6 7 Momentary
ONONON
--
OFF
OFFONON
Current Rating: 17A @125V AC, 12A @ 250V AC1-1/2 HP 250V AC 1, 2 or 3 Phase
Insulation Resistance: 100 Meg ohmsDielectric Strength: 1000V (min.)Base Material: PhenolicActuator & Bushing Material: Brass/Nickel PlateTerminal Type: Screw (#6-32 NC-2 Thread)
SPECIFICATIONS:
Part No.30-1023930-1024030-10241
ActuatorMetalMetalMetal
Type3PST3PDT3PDT
ActionONONON
-OFF
-
OFFONON
Terminal
Mounting Hole: 0.500”
C
C
C
NOTE: ( ) = Momentary
149
SWITCHES STANDARD TOGGLE
Current Rating: 15A @125V AC, 10A @ 250V ACInsulation Resistance: 100 Meg ohmsDielectric Strength: 1000V (min.)Base Material: PhenolicActuator & Bushing Material: Brass/Nickel PlateTerminal Type: Screw (#6-32 NC-2 Thread)
SPECIFICATIONS:
Part No.30-1024330-1024530-10376
ActuatorMetalMetalMetal
Type4PDT4PDT4PDT
ActionONONON
OFF--
ONOFFON
HEAVY DUTY BAT HANDLE TOGGLE SWITCHES - 4PDT
Mounting Hole: 0.500”
Terminal
SEALED HEAVY DUTY BAT HANDLE TOGGLE SWITCHESSPDT, TWO CIRCUIT
Current Rating: 20A @ 125V AC, 10A @ 277V AC21A@ 12-14V DC,
Initial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.) @ 500 V DCDielectric Strength: 1,000V AC for (Min)Base Material: PhenolicActuator & Bushing: Brass Nickle PlatedTerminal Type: .250” Quick Connect
SPECIFICATIONS;
Part No.30-305030-3057
ActuatorMetalMetal
TypeSPSTDPST
ActionONON
--
OFFOFF
Part No.30-340
ActuatorMetal
TypeSPDT (ON) ON OFF
Current Rating: 15A @ 125V AC, 10A @ 250V AC3/4 HP @ 125-250V AC,
Initial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1,000V for (Min)Base Material: PhenolicActuator & Bushing: Brass Nickle PlatedTerminal Type: .250” Quick Connect
HEAVY DUTY BAT HANDLE TOGGLE SWITCHSPDT, TWO CIRCUIT
TOGGLE SWITCH SAFETY GUARD
FeaturesRugged Spring-loaded DesignBlack Steel Base w/ Red urea Plastic CoverFits ALL Metal Lever toggles w/ 15/32 X 32 Bushing
Part No. 30-1320
Rubber BootThread Size: 15/32-32
Action
TOGGLE SWITCH BOOT
Part No. 30-1250
150
SWITCHES PADDLE HANDLE TOGGLE
Current Rating: 10A @125V AC, 6A @ 250V ACInitial Contact Resistance: 20 Meg ohm (Max.)Insulation Resistance: 500V DC 100 Meg ohm (Min.)Dielectric Strength: 1500V AC for 1 minuteContact Material: Brass - Bright Nickel PlateTerminal Material: Brass - Bright Nickel PlateTerminal Type: Solder
SPECIFICATIONS:
Part No.30-089
ActuatorBlack Plastic
TypeDPDT
ActionON OFF ON
STANDARD SIZE PADDLE HANDLE TOGGLE SWITCH
Mounting Hole: 0.500”
LIGHTED PADDLE HANDLE TOGGLE SWITCHES
ELECTRICAL RATING:16A 12V DC MATERIALS:Contact Material: Silver - Silver PlatedTerminal Material: Silver - Silver PlatedLamp: 12V, 55mA, 10,000 Hr Avg. LifeInitial Contact Resistance: 5 Milliohms (Max.)Insulation Resistance: 100 MegaohmsDielectric Strength: 1500V AC (Min.)
SPECIFICATIONS:
Part No.30-89030-89230-894
ActuatorRed
GreenAmber
TypeSPSTSPSTSPST
ActionON ON ON
---
OFF OFFOFF
Mounting Hole: 0.500”
ELECTRICAL RATINGS:20A 125-250V AC 85C Single Pole UL E45221 1/4HP 125V AC 1/2HP 250V AC 3 Pos. UL/CSA1/2HP 125V AC 1HP 250V AC 2 Pos. UL/CSA16A 125-250V AC CSA LR1099016 (4)A 250V AC T85 VDE 8925420A 28V DC Approvals N/A
SPECIFICATIONS:
Part No.30-17030-17130-172
ActuatorBlack NylonBlack NylonBlack Nylon
TypeSPSTSPDTSPDT
Action
STANDARD SIZE PADDLE HANDLE TOGGLE SWITCHES
ON ON ON
OFF ON ON
- -
OFF
Mounting Hole: 0.500”
Mounting Hole: 0.55” x 1.125”
MINI TIPPETTE PADDLE HANDLE TOGGLE SWITCHES
SPECIFICATIONS:
Part No.30-1030830-1031830-10319
ActuatorBlack Nylon
Black Nylon with Amber LensBlack Nylon with Red Lens
TypeSPSTSPSTSPST
ActionON ON ON
OFF OFF OFF
- --
Current Rating: 15A @ 125VAC, 10A @ 250VAC 3/4 HP 125-250VAC
Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V (min.)Base Material: NylonTerminal Type: .250” Quick Connect
NOTE: Lamp Voltage 125Volt/Neon
151
SWITCHES PADDLE HANDLE TOGGLE
AUTOMOTIVE/MARINE TOGGLE SWITCHES
Current Rating: 21A @14V DCInitial Contact Resistance: 20 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V AC for 1 minuteContact Material: Brass Terminal Material: Brass Terminal Type: .250” Quick Connect
SPECIFICATIONS:
Part No.30-125
ActuatorNylon
TypeDPDT
Action(ON) OFF (ON)
SPECIFICATIONS:
Part No.30-16030-16230-16430-16630-168
Current Rating: 20A @ 125V AC, 10A @ 250V ACInitial Contact Resistance: 20 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V AC for 1 minuteContact Material: Brass Terminal Material: BrassTerminal Type: Screw
ActuatorNylonNylonNylonNylonNylon
TypeSPSTSPDTDPSTDPDTDPDT
ActionONONONONON
----
OFF
OFFONOFFONON
NOTE: ( ) = Momentary
AUTOMOTIVE/MARINE TOGGLE SWITCHES
Current Rating: 20A @ 125V AC, 10A @ 250V ACInitial Contact Resistance: 20 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V AC for 1 minuteContact Material: Brass Terminal Material: BrassTerminal Type: .250” Quick Connect
SPECIFICATIONS:
NOTE: ( ) = Momentary
Part No.30-15030-15230-15430-15630-158
ActuatorNylonNylonNylonNylonNylon
TypeSPDTSPDTDPSTDPDTDPDT
ActionON
(ON)ONONON
OFFOFF
--
OFF
ON(ON)OFFONON
REVERSING TOGGLE SWITCH
Mounting Hole: 0.500”
Mounting Hole: 0.500”
Current Rating: 20A @125V AC, 10A @ 250V ACInitial Contact Resistance: 20 Meg ohm (Max.)Insulation Resistance: 500V DC 100 Meg ohm (Min.)Dielectric Strength: 1500V AC for 1 minuteContact Material: Brass Terminal Material: Brass Terminal Type: Solder
SPECIFICATIONS:
Part No.30-088
ActuatorBlack Nylon
TypeDPDT
ActionON OFF ON
STANDARD SIZE PADDLE HANDLE TOGGLESWITCH
Mounting Hole: 0.500”
Mounting Hole: 0.500”
152
SWITCHES ROCKER
POWER ROCKER SWITCH
ROCKER SWITCHES
Current Rating: 16A @ 125V AC, 10A @ 250V ACInitial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 500V DC 100 Meg ohm (Min.)Dielectric Strength: 1500V AC for 1 minuteContact Material: Copper - Silver PlateTerminal Material: Copper - Silver PlateTerminal Type: .250” Quick Connect
SPECIFICATIONS:
ActuatorBlack Nylon
Black Nylon with Red LegendBlack Nylon with Red Legend
Black NylonBlack Nylon
TypeSPSTSPSTSPSTSPDTSPDT
ONONONONON
---
OFF-
OFFOFFOFFONON
Part No.30-1609130-1609330-16703*30-1609430-10080
Action
POWER ROCKER SWITCH
SPECIFICATIONS:
Part No.30-10082
ActuatorNylon
TypeDPDT
ActionON - ON
Current Rating: 16A @ 125V AC, 10A @ 250V ACInitial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 500V DC 100 Meg ohm (Min.)Dielectric Strength: 1500V AC for 1 minuteContact Material: Copper - Silver PlateTerminal Material: Copper - Silver PlateTerminal Type: .250” Quick Connect
SPECIFICATIONS:
Part No.30-10084
ActuatorRed Nylon
TypeSPST
ActionON - OFF
Current Rating: 16A @ 125V AC, 10A @ 250V ACInitial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: 500V DC 100 Meg ohm (Min.)Dielectric Strength: 1500V AC for 1 minuteContact Material: Copper - Silver PlateTerminal Material: Copper - Silver PlateTerminal Type: .250” Quick Connect
SINGLE POLE HEAVY DUTY ROCKER SWITCHES(Moisture and Dust Resistant)
Current Rating: 20A @ 125V AC, 10A @ 277V AC3/4 HP @ 125-250V AC
Initial Contact Resistance: 5 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V AC for 1 minuteGasket: Molded ElastomerCase: UL94 Flame Class, 94V-2Contact Material: BrassTerminal Material: BrassTerminal Type: .250” Quick Connect
SPECIFICATIONS:
Part No.30-60030-67030-61030-620
ActuatorBlack NylonBlack NylonBlack NylonBlack Nylon
TypeSPSTSPSTSPDTSPDT
ActionONONONON
---
OFF
OFF(OFF)
ONON
NOTE: ( ) = Momentary
Recommended Mounting Hole:+.01: 9.381 9.00: 9.127
Fits .830 (21.08) ; 1.4:0 (36.83) panel cutout in.093 (2.36)< .12: (3.18)< .187 (4.7:) thick panels.
C
*= 3/4 HP Rating
Terminal
Mounting Hole: 0.::> ; 1.13>
Mounting Hole: 0.87> ; 1.10>
Mounting Hole: 0.::> ; 1.13>
153
SWITCHES ROCKER
STANDARD ROCKER SWITCHES
MINIATURE POWER ROCKER SWITCHESFor applications such as computers, audio, medical, office instrument
and appliance products.
DOUBLE POLE MINIATURE POWER ROCKER SWITCHES
Mounting Hole: 0.51” x 0.75” @ .04” Panel Thickness0.51” x 0.76” @ .08” Panel Thickness
Current Rating: 5A @ 125V AC, 3A @ 250V ACInitial Contact Resistance: DC 2.5V-1A, 20 Meg ohm (Max.)Insulation Resistance: 500V DC 100 Meg ohm (Min.)Dielectric Strength: 1500V AC for 1 minuteContact Material: Copper - Silver PlateTerminal Material: Copper - Silver PlateTerminal Type: Solder
SPECIFICATIONS:
Part No.30-1008630-10088
ActuatorBlack NylonBlackNylon
TypeSPDTSPDT
ONON
-OFF
ONON
Action
ELECTRICAL RATINGS:10A 125-250V AC 65C UL E45221 CSA LR109901/4HP 125V AC 1/2HP 250V AC UL/CSA10 (4)A 250V AC T90 VDE 4437525A Inrush EN61058-110A 28V DC Approvals N/AMATERIALS:Body: Nylon 6.6Actuator: Nylon 6.6Contact Gap: 3mm (.118)Contact Material: Silver
SPECIFICATIONS:
Part No.30-860
30-16844
ActuatorBlack NylonBlack Nylon
TypeSPSTSPDT
ActionONON
--
OFFON
OFF
ELECTRICAL RATINGS:16A 125-250V AC 65C UL E45221 1HP 30V DC UL/CSA1/2A 125V AC UL/CSA10A 125-250V AC 65C CSA LR1099010 (6)A 250V AC T100 VDE 7517175A Inrush EN61058-110A 28V DC Approvals N/AMATERIALS:Body: Nylon 6.6Actuator: Nylon 6.6Contact Gap: 3mm (.118)Contact Material: Silver Alloy
SPECIFICATIONS:
Part No.30-250
30-16705
ActuatorBlack Nylon
White Nylon w/Black Legend
TypeDPSTDPST
ActionONON
OFFOFF
--
Electrical Ratings:SPST snap action Rocker.6A @125 VAC or 3A @250 VAC (UL)3A@250 VAC (CQC)Rating: 3A@125 VAC, 250 VAC pending for VDEInitial Contact resistance: 20m ohm Max.Insulation Resistance: 100 Ohm @500 VDCDielectric Strength: 1,000 VAC for 1 minuteElectrical/mechanical life: 10,000 cyclesTemperature range: 0 to 88 degrees centigradeBase: Nylon66, UL rated 94V-2 min.Spring: Piano wireStationary contact: Silver Alloy
Micro Rocker Switches
A very small Rocker with a good “feel” inthe action, excellent for small appliances,battery operated portable devices. This isa SPST switch and the black and whiteactivators are marked with the “universal”digital “l” and “0” to indicated ON and OFF.The red actuator is plain, no markings.
Note that Dimension“Y” mounting holevaries with panel
thickness as below.Dimension Z is 9.2mm
for all.
Part No. Type Action Actuator30-870 SPST On-Off White (with o – markings in black)30-872 SPST On-Off Black (with o – markings in white)30-874 SPST On-Off Red (plain, no marking on actuator)
Y
Z
154
SWITCHES ROCKER
MINIATURE ROCKER SWITCHESTwo Color Actuator with Molded in Color Legend.ELECTRICAL RATINGS:
15A 125-250V AC 65C Non Ind UL E45221 1/4HP 125V AC 1/2HP 250V AC UL E45221 12A 125-250V AC CSA LR1099010 (6)A 250V AC T125 VDE7517175A Inrush EN61058-110A 28V DC No ApprovalsMATERIALS:Body: Nylon 6.6Rocker (Opaque): Nylon 6.6Contact Gap: 3mm (.118)Contact Material: Silver Alloy
SPECIFICATIONS:
Part No.30-85030-85230-85430-855
ActuatorBlack Nylon & Red
Black Nylon & GreenBlack Nylon & Blue
Black Nylon & White
TypeSPSTSPSTSPSTDPST
ActionONONONON
----
OFFOFFOFFOFF
Industry Standard size. Snap in mounting.Single and Double Pole. ON-OFF Circuits.
PANEL THICKNESS0.75-1.25
(.029-.049)1.25-2.0
(.049-.079)2.0-3.0
(.079-.118)
DIM X19.2-19.1
(.756-.752)19.4-19.3
(.764-.760)19.8-19.7(.779-.776)
DIM Y13.0-12.9
(.512-.508)13.0-12.9
(.512-.508)13.0-12.9(.512-.508)
MINIATURE ROCKER SWITCHES Current Rating: 10A 250VAC, 1/2 Hp @ 277VAC, 1/4 Hp @125VAC Initial Contact Resistance: <100Meg Ohms @12VDCInsulation Resistance: >20Meg OhmsDielectric Strength (Open Contacts): >1000V for 1 minuteContact Material: Silver AlloyTerminal Material: Copper AlloyBody Material: Nylon 6.6Actuator & Bezel: Nylon 6.6Terminal Type: .187” Quick Connect
Part No. Type Action Actuator
30-16860* DPDT On-(On) Black Nylon30-16870 DPDT On-Off-On Black Nylon *note: 30-16860 is 6A @ 277VAC Mounting Hole: 21.9mm x 19.2mm
( ) = Momentary
MINIATURE ROCKER SWITCHES
Current Rating: 8A @125 V AC, 4A @ 250 V ACInsulation Resistance: 100 Meg ohms (Min.)Dielectric Strength: 1000V (Min.)Base Material: NylonTerminal Type: Solder
SPECIFICATIONS:
Part No.30-65430-656
ActuatorRed NylonRed Nylon
TypeDPDTDPDT
ActionONON
-OFF
ONON
Mounting Hole: 0.515” x 0.625”
STANDARD SIZE ROCKER SWITCHES
ELECTRICAL RATINGS:16A 125-250V AC 85C UL E45221 1/2HP 125V AC 1HP 250V AC 2 Position UL/CSA16A 125-250V AC CSA LR1099016 (4)A 250V AC T85 VDE 62411 20A 28V DC Approvals N/AMATERIALS:Body: Nylon 6.6Actuator: Nylon 6.6Contact Gap(On-Off SP Circuits): 3mm (.118)Contact Material: Silver Alloy
SPECIFICATIONS:
Part No.30-46030-965
ActuatorBlack NylonBlack Nylon
TypeSPDTSPDT
ActionON
(ON)-
OFFON
(ON)NOTE: ( ) = Momentary
155
SWITCHES ROCKER
DOUBLE POLE HEAVY DUTY ROCKER SWITCHES(Moisture and Dust Resistant)
ROCKER SWITCH
ROCKER SWITCH with LED
Mounting Hole: 0.430” x 1.180”
Recommended Mounting Hole:+.015 +.381 +.005 +.127
Fits .830 (21.08) x 1.450 (36.83) panel cutout in.093 (2.36), .125 (3.18), .187 (4.75) thick panels.
C
Current Rating: 20A @ 125V AC, 10A @ 277V AC1-1/2 HP @ 125-250V AC
Initial Contact Resistance: 5 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V AC for 1 minuteGasket: Molded ElastomerCase: UL94 Flame Class, 94V-2Contact Material: BrassTerminal Material: BrassTerminal Type: .250” Quick Connect
SPECIFICATIONS:
Part No.30-63030-66030-64030-68030-65030-69030-695
ActuatorBlack NylonBlack NylonBlack NylonBlack NylonBlack NylonBlack NylonBlack Nylon
TypeDPSTDPSTDPDTDPDTDPDTDPDTDPDT
ActionON
(ON)ONONONON
(ON)
----
OFFOFFOFF
OFFOFFON
(ON)ON
(ON)(ON)
NOTE: ( ) = Momentary
ELECTRICAL RATINGS:20A 125-250V AC 85C UL E45221 1/2HP 125V AC 1HP 250V AC UL/CSA20A 125-250V AC CSA LR1099016 (4)A 250V AC T85 VDE 6241116 (6)A 250V AC T125 5E4 Semko EN61058-1 150A Inrush Semko IEC65 20A 28V DC Approvals N/AMATERIALS:Body: Nylon 6.6Actuator: Nylon 6.6Contact Gap: 3mm (.118)Contact Material: Silver Alloy
SPECIFICATIONS:
Part No.30-564
ActuatorBlack Nylon
TypeDPST
ActionON - OFF
Current Rating: 10A @125V ACInitial Contact Resistance: 20 Meg ohm (Max.)Insulation Resistance: 500V DC 100 Meg ohm (Min.)Dielectric Strength: 1000V AC for 1 minuteContact Material: Brass - Bright Nickel PlateTerminal Material: Brass - Bright Nickel PlateTerminal Type: .250” Quick Connect
SPECIFICATIONS:
Part No.30-084
ActuatorWhite w/ Red LED
TypeSPST
ActionON - OFF
Terminal
Mounting Hole: 1.0” x 1.12”
ROCKER SWITCHES with LED
Mounting Hole: 0.51” x 0.75”
Current Rating: 6A @125 V AC, 3A @ 250 V ACInitial Contact Resistance: DC 2.5V-1A, 20 Meg ohm (Max.)Insulation Resistance: 500V DC 100 Meg ohm (Min.)Dielectric Strength: 1500V AC for 1 minuteContact Material: Copper - Silver PlateTerminal Material: Copper - Silver PlateTerminal Type: Solder
SPECIFICATIONS:
Part No.30-1008330-1008530-16081*
ActuatorBlack Nylon w/ Red LED
Black Nylon w/ Green LEDBlack Nylon w/Amber LED
TypeSPSTSPSTSPST
ActionONONON
---
OFFOFFOFF
*30-16081 has .187” Quick Connect Terminal
156
SWITCHES ROCKER
MINIATURE ROCKER SWITCH
MINIATURE SNAP-IN ROCKER SWITCHES
TINY ROCKER SWITCHES
Mounting Hole: .756” x .508”
Ideal for small appliances or controls with limited space. Themini rocker switch is capable of handling high currents as the
traditional larger switches. This product range is electricallyapproved in thirteen countries.
MINIATURE ROCKER SWITCHES
Mounting Hole: .51” x .751”
ELECTRICAL RATINGS:10A 125-250V AC 65C UL E45221 CSA LR109901/4HP 125V AC 1/2HP 250V AC UL/CSA6A 277V AC UL15 (4)A 125-250V AC 90C
1/2HP 250V AC UL1/4HP 125V AC
10 (4)A 250V AC T90 VDE4437525A Inrush EN61058-110A 28V DC Approvals N/AMATERIALS:Body: Nylon 6.6Actuator: Nylon 6.6Contact Gap: 3mm (.118)Contact Material: Silver Alloy
SPECIFICATIONS:
Part No.30-846
ActuatorBlack
TypeDPDT
ActionON ON-
ELECTRICAL RATINGS:12A 125-250V AC UL E45221 1/2HP 125V AC UL E45221 12A 125-250V AC CSA LR1099010 (6)A 250V AC T100 VDE8866210A 24V DC
SPECIFICATIONS:
Part No.30-88030-88230-884
ActuatorBlack Nylon
Black Nylon w/ White Imprint (A)Black Nylon w/ White Imprint (B)
TypeSPSTSPSTSPST
ActionON - OFFON - OFFON - OFF
SPECIFICATIONS:
Part No.**30-002*30-004
**30-042**30-043
ActuatorBlack NylonBlack NylonBlack NylonBlack Nylon
TypeSPDTSPDTSPSTDPST
ActionONONONON
-OFF
--
ONONOFFOFF
Current Rating: *13A @ 125V AC, 10A @ 250V AC1/2 HP @ 125-250V AC, 5A @ 14V DC**16A @ 125V AC, 10A @ 250V AC3/4 HP @ 125-250V AC, 5A @ 14V DC
Initial Contact Resistance: 5 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V AC for 1 minuteContact Material: Copper AlloyTerminal Material: Silver Plate - Copper AlloyTerminal Type: .187” Quick Connect
Tracking resistance: KB250Humidity resistance at91-95% relative humidity: 48 hoursSwitch body/rocker: Nylon 66Current carrying partsContact points: Silver AlloyEnd terminal: Copper Alloy
with Silver Alloycontact
Pivot terminal: Copper Alloy,Silver plated
Moving contact: Copper Alloy with Silver Alloycontact
SPECIFICATIONS:
Part No.30-1660530-1660630-1660730-1660830-16612
ActuatorBlack Nylon with Red 0-I Legend
Black NylonBlack NylonBlack NylonBlack Nylon
TypeSPSTDPDTSPSTDPSTSPDT
ActionONONONONON
-----
OFFONOFFOFFON
Current Rating: 10A @ 125V AC, 6A @ 250V ACInitial Contact Resistance: 50 Meg ohm (Max.)Insulation Resistance: DC 500V 100 Meg ohms (Min.)Dielectric Strength: AC 1500V 1 min.Base Material: Nylon UL 94V-2 Terminal Material: Brass/Silver Plate Terminal Type: .187” Quick Connect
PANEL THICKNESS0.75-1.25
(.029-.049)1.25-2.0
(.049-.079)2.0-3.0
(.079-.118)
DIM X19.2-19.1
(.756-.752)19.4-19.3
(.764-.760)19.8-19.7
(.779-.776)
DIM Y21.9-22.0
(.862-.866)21.9-22.0
(.862-.866)21.9-22.0
(.862-.866)
PANEL THICKNESS0.75-1.24 (.030-.049)1.25-1.99 (.049-.078)2.00-3.00 (.079-.118)
DIM X19.1-19.2 (.752-.756)19.3-19.4 (.760-.764)19.7-19.8 (.776-.780)
157
SWITCHES ROCKER
LIGHTED ROCKER SWITCHES
APPLIANCE ROCKER SWITCHES
LIGHTED STANDARD SIZE ROCKER SWITCHES
LIGHTED STANDARD SIZE SNAP-IN ROCKER SWITCHES
Current Rating: 16A @ 125V AC, 12A @ 250V AC3/4 HP @ 125-250V AC, 10A @ 14V DC
Initial Contact Resistance: 5 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V AC for 1 minuteContact Material: Copper AlloyTerminal Material: Copper AlloyTerminal Type: .250” Quick Connect
SPECIFICATIONS;
Part No.30-71030-72030-73030-740
ActuatorBlack NylonBlack Nylon
Green Nylon*Amber Nylon*
TypeSPSTSPDTSPSTSPST
ActionONONONON
----
OFFONOFFOFF
*Lamp (is dependent) high intensity neon with 1/4 watt 22 K Ohmresistor, with 10,000 hours of life for 125 volts.
SPECIFICATIONS:
*30-16740 RATED 16A @ 125VAC, 10A @ 250VACNeon Light @ 110V AC
Part No.30-39030-395
30-16740*
ActuatorAmber NylonRed Nylon
Translucent Nylon
TypeSPSTSPSTSPST
ActionONONON
---
OFFOFFOFF
Current Rating: 15A @ 125V AC, 7.5A @ 250V ACInitial Contact Resistance: 5 Meg ohm (Max.)Insulation Resistance: 100 Meg ohm (Min.)Dielectric Strength: 1000V AC for 1 minuteContact Material: Copper AlloyTerminal Material: Copper AlloyTerminal Type: .250” Quick Connect
Mounting Hole: 1.125” x 0.550”
Mounting Hole: 1.125” x 0.550”
ELECTRICAL RATINGS:15A 125-250V AC T85 UL E45221 1/2HP 125V AC 1HP 250V UL E4522116A 125-250V AC Res CSA LR1099016 (4)A 250V AC T85 VDE 45152 20A 28V DC Approvals N/AMATERIALS:Body: Nylon 6.6Actuator Transparent: PolycarbonateContact Gap: u MicroContact Material: Silver Alloy
SPECIFICATIONS:
Part No.30-06030-069
ActuatorRed Lens*
Red Translucent**
TypeSPSTSPST
ActionONON
OFFOFF
--
* Lamp Voltage 12V AC/DC Incandescent** Lamp Voltage 105-130V AC Neon
ELECTRICAL RATINGS:15A 125-250V AC T85 UL E45221 1/2HP 125V AC 1HP 250V UL E4522116A 125-250V AC Res CSA LR1099016 (4)A 250V AC T85 VDE 45152 20A 28V DC Approvals N/AMATERIALS:Body: Nylon 6.6Actuator Transparent: PolycarbonateContact Gap: u MicroContact Material: Silver Alloy
SPECIFICATIONS:
Part No.30-55030-55230-556
ActuatorRed Lens*
Green Lens*Amber*
TypeSPSTSPSTSPST
ActionONONON
OFFOFFOFF
---
* NOTE: User Note: The light bulb incorporated in this switch mustbe connected to 12 volts AC or DC and NOT to 125 volts. The 125 voltrating applies to switch contacts, NOT to the light.
* NOTE: User Note: The light bulb incorporated in this switch must be connected to 12 volts AC or DC and NOT to125 volts. The 125 volt rating applies to switch contacts, NOT to the light.
Lead Terminal 1, Line In terminal2, Line Out terminal 3.
Light will be ON or OFF whenswitch is In ON or OFF position.
12V AC/DC Incandescent
158
SWITCHES ROCKER
SQUARE BEZEL NUT MOUNTED ROUND ROCKER SWITCHES
Current Rating: 6A 250VAC, 10A 125VAC Initial Contact Resistance: <50Meg Ohms @12VDCInsulation Resistance: >100Meg OhmsDielectric Strength (Open Contacts): >1500V for 1 minuteContact Material: Silver Plated BrassTerminal Material: Copper AlloyBody Material: Nylon (UL 94V-2)Actuator & Bezel: Nylon (UL 94V-2)Terminal Type: .187” Quick ConnectMounting Hardware: M20-P1.0
Panel Cut-out: 20.2mm (.79”)Maximum Panel thickness 6.0 mm
Current Rating: 6A 250VAC, 10A 125VAC Initial Contact Resistance: <50Meg Ohms @12VDCInsulation Resistance: >100Meg OhmsDielectric Strength (Open Contacts): >1500V for 1 minuteContact Material: Silver Plated BrassTerminal Material: Copper AlloyBody Material: Nylon (UL 94V-2)Actuator & Bezel: Nylon (UL 94V-2)Terminal Type: .187” Quick ConnectLamp Voltage: AC= 110V neon, DC= LED 2V *@20ma
(*resistor needed for other voltages)
Mounting Hardware: M20-P 1.0Part No. Type Action Lamp / Actuator Color
30-16402 SPST On-Off AC Lamp, Red30-16404 SPST On-Off AC Lamp, Amber30-16405 SPST On-Off AC Lamp, Green30-16422 SPST On-Off DC Lamp, Red30-16423 SPST On-Off DC Lamp, Amber30-16425 SPST On-Off DC Lamp, Green30-16426 SPST On-Off DC Lamp, Blue
LIGHTED, SQUARE BEZEL NUT MOUNTED ROUND ROCKER SWITCHES
Part No. Type Action Actuator
30-16200 SPST On-Off Bi-Color Actuator30-16220 SPST (On)-Off Black Actuator30-16260 SPST On-(Off) Black Actuator30-16330 SPDT On-(On) Black Actuator30-16340 SPDT On-Off-(On) Black Actuator30-16210 SPDT On-On Black Actuator30-16215 SPDT On-Off-On Black Actuator30-16360 SPDT (On)-Off-(On) Black Actuator
Panel Cut-out: 20.2mm (.79”)Maximum Panel thickness 6.0 mm
AC - NEONDC - LED
( ) = Momentary
ROCKER SWITCHES
SPECIFICATIONS:
Part No.30-1005530-1005630-1005830-10059
ActuatorRed NylonRed NylonRed Nylon
Black Nylon w/ LED
TypeSPDTDPSTDPDTSPST
Current Rating: 5A @ 125V AC, 3A @ 250V ACInitial Contact Resistance: DC 2.5V-1A, 20 Meg ohm (Max.)Insulation Resistance: 500V DC 100 Meg ohm (Min.)Dielectric Strength: 1500V AC for 1 minuteContact Material: Copper - Silver PlateTerminal Material: Copper - Silver PlateTerminal Type: Solder
ActionONONONON
----
ONOFFONOFF
Mounting Hole: 0.812” (13/16)
159
SWITCHES ROCKER
Current Rating: 3A 250VAC, 6A 125VAC Initial Contact Resistance: <50Meg Ohms @12VDCInsulation Resistance: >100Meg Ohms @500VDielectric Strength (Open Contacts): >1000V for 1 minuteContact Material: Silver Plated BrassTerminal Material: Copper AlloyBody Material: Nylon (UL 94V-2)Actuator & Bezel: Nylon (UL 94V-2)Terminal Type: .110” Quick ConnectMounting Hardware: M20-P1.0
Part No. Type Action Actuator
30-16150 SPST On-Off Black Actuator30-16155 SPDT On-On Black Actuator 30-16160 DPST On-Off Black Actuator
RECTANGULAR BEZEL ROUND ROCKER SWITCHES
Panel Cut-out: 12.2mm (.48”)Maximum Panel thickness 6.0 mm
SNAP-IN ROUND ROCKER SWITCHESCurrent Rating: 6A 250VAC, 10A 125VAC Initial Contact Resistance: <50Meg Ohms @12VDCInsulation Resistance: >100Meg OhmsDielectric Strength (Open Contacts): >1500V for 1 minuteContact Material: Silver Plated BrassTerminal Material: Copper AlloyBody Material: Nylon (UL 94V-2)Actuator & Bezel: Nylon (UL 94V-2)Terminal Type: .187” Quick Connect
Part No. Type Action Actuator
30-16060 SPST On-Off Bi-Color Actuator30-16062 SPST (On)-Off Black Actuator30-16066 SPST On-(Off) Black Actuator30-16068 SPDT On-(On) Black Actuator30-16110 SPDT On-Off-(On) Black Actuator30-16070 SPDT On-On Black Actuator30-16072 SPDT On-Off-On Black Actuator30-16074 SPDT (On)-Off-(On) Black Actuator
Panel Cut-out: 20.2mm (.79”)Maximum panel thickness 3.0 mm
Current Rating: 6A 250VAC, 10A 125VAC Initial Contact Resistance: <50Meg Ohms @12VDCInsulation Resistance: >100Meg OhmsDielectric Strength (Open Contacts): >1500V for 1 minuteContact Material: Silver Plated BrassTerminal Material: Copper AlloyBody Material: Nylon (UL 94V-2)Actuator & Bezel: Nylon (UL 94V-2)Terminal Type: .187” Quick ConnectLamp Voltage: AC= 110V, DC= 12V
Part No. Type Action Lamp / Actuator Color
30-16182 SPST On-Off AC Lamp, Red30-16183 SPST On-Off AC Lamp, Amber30-16185 SPST On-Off AC Lamp, Green30-16122 SPST On-Off DC Lamp, Red30-16123 SPST On-Off DC Lamp, Amber30-16125 SPST On-Off DC Lamp, Green30-16126 SPST On-Off DC Lamp, Blue
Panel Cut-out: 20.2mm (.79”)Maximum Panel thickness 3.o mm
( ) = Momentary
LIGHTED SNAP-IN ROUND ROCKER SWITCHES
160
SWITCHES ROCKER
LIGHTED SNAP-IN ROUND ROCKER SWITCHES
Current Rating: 6A 250VAC, 10A 125VAC Initial Contact Resistance: <50Meg Ohms @12VDCInsulation Resistance: >100Meg OhmsDielectric Strength (Open Contacts): >1500V for 1 minuteContact Material: Silver Plated BrassTerminal Material: Copper AlloyBody Material: Nylon (UL 94V-2)Actuator & Bezel: Nylon (UL 94V-2)Terminal Type: .187” Quick ConnectLamp Voltage: AC= 110V neon, DC= LED 2V* @20ma
(*resistor needed for other voltages)
Part No. Type Action Lamp / Actuator Color
30-16282 SPST On-Off AC Lamp, Red30-16283 SPST On-Off AC Lamp, Amber30-16285 SPST On-Off AC Lamp, Green30-16222 SPST On-Off DC Lamp, Red30-16223 SPST On-Off DC Lamp, Amber30-16225 SPST On-Off DC Lamp, Green30-16226 SPST On-Off DC Lamp, Blue
Panel Cut-out: 20.2mm (.79”) Maximum Panel thickness 3.0 mm
AC - NEON
DC - LED
Round Rocker Switch Cover
No. 30-1600 fits Round RockerSwitches up to 23mm(.90”) dia.
Using an LED
An LED (light emitting diode) requires about two volts to operate and twenty milliamps of current. Acurrent limiting resistor must be used in series with an LED to prevent current over 20 mA from flow-ing; otherwise, your LED will be damaged. You may simply use Ohm’s law to calculate the resistor
value. Here is an example, We have a circuit operating at 12 volts DC, and need toknow the value of a resistor to use. The LED “wants” two volts to operate ; so subtract2 from the 12 volts which is of course, ten. Plug the “ten” in at “E” and divide by “I” or.020 amps. The result is 500 ohms for the resistor value
If you forget to subtract the two volts, the resistor value will be 600 and the LED willnot be at maximum brightness. However, it will last much longer! (about double normal life).
Another formula you can use is R=50(V-2). The R is for resistor, the V for voltage. We like this oneas it is easy to recall and do in your head.
LED wth DC (Direct Current)
When using an LED with AC, a diode must be placed inseries with the LED. Because AC will only be flowing 1/2the time, we use a variation on the easy formula shown tothe left(bottom). Use R=25(V2.7), which includes the volt-age drop across the diode.
So, if you have a circuit using 28 volts AC, multiply 25.3(or 28V -2.7), times 25 equals 632 ohms. We need to usea standard value resistor, so use 680 ohms for “R”.
LED wth AC (Alternating Current)
DC Volts 5V 6V 12V 24VResistor (ohms) 150 180 470 1200
AC Volts 6V 12V 24V 48V 117VResistor (ohms) 82 220 560 1200 3K
Typical voltages used in electronics and resistor values (rounded to nearest standard resistor).