Post on 08-Jul-2018
8/19/2019 Pap Modul 1-Design Introductions
1/18
CHEMICAL PROCESS
DESIGNPAP-LEILY NK-2014
8/19/2019 Pap Modul 1-Design Introductions
2/18
8/19/2019 Pap Modul 1-Design Introductions
3/18
A&'() *ESI+N
*esign is a creati#e acti#it," and as such can $eone of the most re%arding and satisf,ing acti#itiesundertaen $, an engineer.
)he design does not exist at the start of the ro/ect.
)he designer $egins %ith a secic o$/ecti#e orcustomer need in mind and" $, de#e!oing ande#a!uating ossi$!e designs" arri#es at the $est %a,
of achie#ing that o$/ecti#e$e it a $etter chair" ane% $ridge" or
for the chemica! engineer"a ne% chemica! roductor roduction rocess.
8/19/2019 Pap Modul 1-Design Introductions
4/18
*esign - Externa! factors
1-Economic considerations are o$#ious!, a ma/orconstraint on an, engineering design !ants mustmae a rot.
2-)ime %i!! a!so $e a constraint. )he time a#ai!a$!e forcom!etion of a design %i!! usua!!, !imit the num$er ofa!ternati#e designs that can $e
3 Ph,sica! !a%
4- esources
5- Safet, egu!ations
6- Standard and codes
8/19/2019 Pap Modul 1-Design Introductions
5/18
Process constraints
8/19/2019 Pap Modul 1-Design Introductions
6/18
*esign Procedures
8/19/2019 Pap Modul 1-Design Introductions
7/18
7hemica! engineering ro/ects can $e di#ided intothree t,es" deending on the no#e!t, in#o!#ed
1.8odications" and additions" to existing !ant9usua!!, carried out $, the !ant design grou.
2. Ne% roduction caacit, to meet gro%ing sa!esdemand" and the sa!e of esta$!ished rocesses $,
contractors. eetition of existing designs" %ithon!, minor design changes.
3. Ne% rocesses" de#e!oed from !a$orator,
research" through i!ot !ant" to a commercia!rocess. E#en here" most of the unit oerations and
*esign concets
8/19/2019 Pap Modul 1-Design Introductions
8/18
*esign-;o%
8/19/2019 Pap Modul 1-Design Introductions
9/18
*esign stages
)he se!ection rocess can $econsidered to go through the fo!!o%ingstages
Possi$!e designs
8/19/2019 Pap Modul 1-Design Introductions
10/18
Setting the *esign &asis )he most imortant ste in starting a rocess design istrans!ating the customer need into a design $asis . It %i!!norma!!, inc!ude the roduction rate of the main roducttogether %ith the information on constraints that %i!! in;uencethe design such as -
1- )he s,stem of the unit to $e used
2- )he nationa! the !oca! or coman, design codes that must $efo!!o%ed
3- *etai!s of ra% materia!s that a#ai!a$!e
4- Information on otentia! sites %here the !ant might $e!ocated
5- Information on the condition " a#ai!a$i!it, and rices of uti!it,
ser#ices
8/19/2019 Pap Modul 1-Design Introductions
11/18
8/19/2019 Pap Modul 1-Design Introductions
12/18
7ontinuous Process
are designed to oerate 24 hours a da," @da,s a %ee" throughout the ,ear.
Some do%n time %i!! $e a!!o%ed formaintenance and" for some rocesses"cata!,st regeneration. )he !ant attainment9that is" the ercentage of the a#ai!a$!e hours
in a ,ear that the !ant oerates" %i!! usua!!,$e 0 to 5B. C hours oerated "
7ontinuous rocesses %i!! usua!!, $e moreeconomica! for !arge sca!e roduction.
8/19/2019 Pap Modul 1-Design Introductions
13/18
&atch Process
&atch rocesses are designed to oerateintermittent!,. Some"or a!!" the rocess units$eing fre:uent!, shut do%n and started u.
&atch rocesses are used %here some ;exi$i!it,is %anted in roduction rate or roductsecication.
Production rate !ess than 5 x 106 gDh A range of roducts or roduct secications Se#ere fou!ing Short cata!,st !ife Ne% roduct (ncertain design
8/19/2019 Pap Modul 1-Design Introductions
14/18
7ontinuous #s &atch Process
Production rate greaterthan 5 x 106 gDh
Sing!e roduct
No se#ere fou!ing
+ood cata!,st !ife
Pro#en rocessesdesign
Esta$!ished maret
Production rate !ess
than 5 x 106 gDh
A range of roducts or
roduct secications
Se#ere fou!ing
Short cata!,st !ife
Ne% roduct
(ncertain design
8/19/2019 Pap Modul 1-Design Introductions
15/18
7'*ES AN* S)AN*A*S
IN engineering ractice the, co#er
1. 8ateria!s" roerties and comositions.
2. )esting rocedures for erformance" comositions":ua!it,.
3. Preferred sies9 for exam!e" tu$es" !ates"
sections.4. *esign methods" insection" fa$rication.
5. 7odes of ractice" for !ant oeration and safet,.
8/19/2019 Pap Modul 1-Design Introductions
16/18
Standards -exam!es
(nited Kingdom &ritish Standards Institution
8/19/2019 Pap Modul 1-Design Introductions
17/18
?A7)'S '? SA?E)Y
8/19/2019 Pap Modul 1-Design Introductions
18/18
S,stem of units