Post on 02-Apr-2021
MU-L/LDSVertical in line centrifugal pumps
Pompe centrifughe verticali in line
MU-LVERTICAL IN LINECENTRIFUGAL PUMPSPOMPE CENTRIFUGHEVERTICALI IN LINE
USEFresh and sea water, condensate, oils chemical and petro-chemical products.
IMPIEGHIPer acqua dolce, acqua mare, condensato, prodotti chimici, petrolchimici.
MAIN APPLICATIONS Shipbuilding industry, heating plants, air conditioning sy-stems, aqueducts, effluent treatment plants, fire fighting, petrochemical plants, etc...
PRINCIPALI APPLICAZIONI Applicazioni per uso caratteristico, impianti di riscaldamento, impianti di condizionamento, acquedotti, trattamento acque, antincendio, con-vogliamento idrocarburi.
MAIN FEATURES
CARATTERISTICHE COSTRUTTIVE
PUMP: centrifugal type with volute casing, vertical construc-tion, single stage, single flow, in line flanges.POMPA: centrifuga con corpo a spirale orizzontale monostadio ad uni-co flusso ed aspirazione assiale.
IMPELLER: high efficiency, close type, statically and dynami-cally balanced.Axial thrust balancing by means of annular chamber with balancing holes located behind the impeller.GIRANTE: di tipo chiuso ad elevato rendimento, equilibrata staticamen-te e dinamicamente. Equilibratura della spinta assiale mediante camera anulare situata po-steriormente alla girante stessa e munita di fori di bilanciamento.
MOUNTING SYSTEM: shaft supported by radial and thrust ball bearings either grease or self-lubricated. The bracket is normally made of cast-iron or manufactured in bronze or stainless steel for special executions (non-magnetic pumps).SUPPORTAZIONE: albero supportato da cuscinetti radiali a sfera a sin-gola e doppia corona di sfere in grado di reggere alle spinte assiali e radiali con lubrificazione a grasso o in versione autolubrificata. Suppor-to costruito normalmente in ghisa, oppure in bronzo o acciaio inox per utilizzi speciali (pompe amagnetiche).
SEAL: single mechanical seals to DIN 29960. Special me-chanical seals or cartridge type, for specific application or aggressive liquids. Possibility to install soft packing with ex-ternal flushing. For temperature higher than 120°C, it is pos-sible to fit the pump with a cooling chamber.TENUTA: tenuta meccanica singola normalizzata DIN 29960. Tenute speciali e a cartuccia per liquidi ed applicazioni particolari. Possibilità di installare tenute a baderna con flussaggio esterno. Per temperature superiori ai 120 °C possibilità di dotare la pompa di camera di raffred-damento della tenuta.
SELF-PRIMING: some listed models can be supplied with a self-priming element either with liquid ring or with air ejector.AUTOADESCANTE: alcuni i modelli elencati possono essere forniti di elemento autoadescante ad anello liquido o con eiettore ad aria.
BACK PULL OUTIt is possible to remove the rotating components without disturbing pipes, pump casing and motor by using a flexible spacer coupling.
SMONTAGGIOImpiegando un giunto spaziatore è possibile sfilare la parte rotante sen-za intervenire sulle tubazioni, corpo-pompa e motore.
BASE PLATEThe base plate is usually cast with pump casing for small and medium size pumps in order to increase the structural stiffness. For larger pumps a welded steel base plate is pro-vided.
BASAMENTOLa base è realizzata in una unica fusione con il corpo per le pompe me-dio/piccole, di carpenteria per quelli di taglia maggiore.
MOTOR FRAME The motor frame supporting the electric motor is normally made of welded steel. For special executions (non magnetic) it can be manufactured in stainless steel.
LANTERNALa lanterna di unione pompa-mo-tore elettrico è costruita normal-mente in acciaio elettrosaldato. Per esecuzioni speciali (amagne-tiche) può essere costruita in ac-ciaio inox.
SPECIAL VERSIONSSpecial versions accor-ding to Naval Ru-les are also availa-ble: shock-proof, vibration-proof, noise-proof, non magnetic version.
COSTRUZIONISPECIALISono previste co-struzioni a norma MARINA MILI-TARE: antishock, ant i v ib raz ione, antirumore, ama-gnetiche.
2
32
MU-LDSPERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
1450 RPM
CAPACITY PORTATA Q m3/h
32-160
40-160
50-160 65-160
32-200 40-200
40-250
65-400
65-200
80-160
80-200 100-200
65-315
125-250
100-250
65-250
80-250
80-400 100-400125-400
150-400 250-400
250-315
200-315150-315125-315100-315
80-315
150-250
200-250
50-250 250-250250-250
300-300
LDS
LDS
50-200
40-315
LDS
400-315
50-315
125-500
LDS
LDS
350-315
LDS
450-450
350-250
25-160
4 5 10 20 30 40 100 200 300 400 500 1000
2
3
4
5
10
20
30
40
50
100
100
3020 40 50 100 200 300 400 500 1000 2000 80003000 5000
10
20
30
40
50
200
300
400
500160
2000 3000
H feet
USGPM
H mt
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
CAPACITY PORTATA Q m3/h
2900 RPM
10 20 30 40 50 100 200 300 400 500 1000 2000 3000
H feetH mt
32-160
32-200
40-1
60
40-200
40-250
50-160
50-200
50-250
65-160
65-250
65-31550-315
80-160
80-200
80-250
100-200
100-250
100-315125-315
125-250
80-31540-315
25-160
65-200
USGPM
2 3 4 5 10 20 30 40 50 100 200 300 15
20
25
30
40
50
60
70
80
90100
120
140
50
60
70
80
90100
200
300
400
500
500 1000
VERTICAL IN LINE DOUBLE SUCTIONCENTRIFUGAL PUMPSPOMPE CENTRIFUGHE VERTICALI IN LINEA DOPPIA ASPIRAZIONE
DESCRIPTIONSingle stage vertical centrifugal pumps in spacer coupling design. Casing with in-line flanges and with high efficiency double inlet impeller, low NPSH required and balanced axial thrust, flow rate up to 3.500 m3/h.
DESCRIZIONEPompe centrifughe monostadio verticali con giunto elastico spazia-tore. Corpo con flange in-line, girante a doppia aspirazione con alto rendimento, basso NPSH richiesto e spinta assiale bilanciata, portata fino a 3.500 m3/h.
MAIN APPLICATIONS Fresh water, sea water, industrial water, condensate, brine, oils and other clean liquids.Shipbuilding industry: ballast, hull and general services, co-oling, circulation.Land based industry: circulation, cooling, water supply and general services.
PRINCIPALI APPLICAZIONIAcqua dolce, acqua di mare, acqua industriale, condensato, brine, idrocarburi ed altri liquidi puliti.Settore navale: servizi di zavorra, bilanciamento, servizi generali, raf-freddamento, circolazione.Settore industriale: circolazione, raffreddamento, servizi vari.
VERSIONSMU-LDS pumps are now available in six sizes. Wetted ma-terial can be in cast iron, nickel-aluminium bronze, stainless steel or special alloy. Automatic priming system execution by means of ejector or vacuum pump.Special executions according to Naval rules: shock-proof, noise-proof, vibration-proof, non magnetic.
VERSIONI Le pompe MU-LDS sono disponibili in sei grandezze. Le parti bagnate possono essere in ghisa, bronzo al nickel alluminio, acciao inox o leghe speciali. Sistema di autoadescamento automatico con eiettore ad aria o pompa del vuoto.Sono previste costruzioni a norma MARINA MILITARE: an-tishock, antirumore, antivibrazione, amagnetiche.
MAIN FEATURES
CARATTERISTICHE COSTRUTTIVE
MU-LDS pumps are designed in order to offer best possible performance and lowest possible maintenance. BACK PULL-OUT design allows maintenance on internal parts without remo-ving motor and pipes. Easy replacement of be-arings and seal without pump dismantling.
Le pompe MU-LDS sono progettate per offrire le migliori perfor-mance con la minima manutenzione. La costruzione BACK PULL-
OUT permette l’estrazione delle parti interne senza dover rimuovere il motore e le tubazioni. E’ anche possibile la sostituzione della tenuta meccanica e dei cuscinetti senza smontare completamente la pompa.
CASING: Casing is of the double volute type to reduce radial load on impeller and ensure maximum working life of bea-rings and mechanical seal. CORPO: : Il corpo è di tipo a doppia voluta per minimizzare la spinta radia-le sulla girante ed aumentare la durata di cuscinetti e tenuta meccanica.
MECHANICAL SEAL: High quality mechanical seal (silicon carbide/silicon carbide/viton) for a wide range of applica-tions. Mechanical seal is cartridge design for easy installation and removing. Soft packing is also available TENUTA MECCANICA: Tenuta meccanica di alta qualità (carburo di si-licio/carburo di silico/viton) per un ampia gamma di applicazioni. La tenuta è del tipo a cartuccia per una facile installazione e rimozione. E’ disponibile anche la versione con tenuta a baderna.
BEARING BRACKET AND MOTOR STOOL: External grease bearings in special bracket specially designed for ease of maintenance. Bracket design allows the replacement of me-chanical seal and bearings without dismantling the pump completely.The motor stool in welded steel to reduce vibrations has got a wide opening to facilitate maintenance.
SUPPORTO E CARENA: : Cuscinetti a grasso installati in un suppor-
to esterno, progettato ap-positamente per facilitare
le operazioni di manu-tenzione. Il design del supporto permette la sostituzione della tenu-
ta meccanica e dei cu-scinetti senza richiedere lo smontaggio completo della pompa.La carena portamotore in acciaio è caratterizzata da elevata resistenza in modo da annullare le vibrazioni durante il funzionamento. E’ dotata di un ampia aper-tura per le operazioni di manutenzione e smontag-gio delle parti interne.
87
PUMP DIMENSIONSDIMENSIONI POMPA
PUMP TYPETIPO POMPA
FLANGES DIMENSIONSDIMENSIONI FLANGE
(UNI 2223-2229 PN 10 UNI 2223-2229 PN 16*)
HOLES N.N. FORI
DRAI
NAGE
DREN
AGGI
O
V/GA
UGE
VUOT
OMET
RO
P/GA
UGE
MAN
OMET
RO
WEIGHT**PESO**
DIS B C E F G H L N S O U1 U2 MU DNs DNd D D’ K K’ g g’ DNs DNd D1 PM1 PM2 Kg1 320 270 320 270 360 100 237 19 18 140 - - 25-160 L 40 25 150 115 110 85 18 14 4 4 1/4’’G 1/4’’G 1/4’’G 601 360 310 360 310 395 130 360 19 18 140 - - 32-160 L 50 40 165 150 125 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 901 350 295 350 295 395 135 360 26 18 140 - - 32-200 L 50 40 165 150 125 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 901 350 295 350 295 420 145 360 24 18 140 - - 40-160 L 65 50 185 165 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 951 360 310 360 310 440 150 360 27 18 140 - - 40-200 L 65 50 185 165 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1001 360 310 360 310 475 135 360 24 18 140 - - 40-250 L 65 50 185 165 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1051 520 465 520 465 700 165 470 27 18 140 - - 40-315 L 65 50 185 165 145 125 18 18 4 4 3/8’’G 3/8’’G 3/8’’G 2351 350 295 350 295 450 155 360 27 18 140 - - 50-160 L 80 65 200 185 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1001 360 310 360 310 480 150 360 22 18 140 - - 50-200 L 80 65 200 185 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1001 425 370 425 370 510 150 360 22 18 140 - - 50-250 L 80 65 200 185 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1201 520 465 520 465 760 160 470 22 18 140 - - 50-315 L 80 65 200 185 160 145 18 18 4 4 3/8’’G 3/8’’G 3/8’’G 2451 385 330 385 330 510 165 360 27 18 140 - - 65-160 L 100 80 220 200 180 160 18 18 8 4 1/4’’G 1/4’’G 1/4’’G 1101 415 360 415 360 510 160 360 22 18 140 - - 65-200 L 100 80 220 200 180 160 18 18 8 4 1/4’’G 1/4’’G 1/4’’G 1151 455 400 455 400 705 193 470 28 18 140 - - 65-250 L 100 80 220 200 180 160 18 18 8 4 3/8’’G 3/8’’G 3/8’’G 2001 520 465 520 465 760 170 470 27 18 140 - - 65-315 L 100 80 220 200 180 160 18 18 8 4 3/8’’G 3/8’’G 3/8’’G 2501 620 565 620 565 850 205 470 40 22 140 - - 65-400 L 100 80 220 200 180 160 18 18 8 4 3/8’’G 3/8’’G 3/8’’G 3051 415 360 415 360 540 170 360 22 18 140 - - 80-160 L 125 100 250 220 210 180 18 18 8 8 1/4’’G 1/4’’G 1/4’’G 1251 450 400 450 400 720 215 470 22 18 140 - - 80-200 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 2001 455 400 455 400 720 196 470 22 18 140 - - 80-250 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 2201 520 465 520 465 780 205 470 27 18 140 - - 80-315 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 2601 620 565 620 565 890 218 530 25 22 180 - - 80-400 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 3751 520 465 520 465 730 235 470 25 18 140 - - 100-200 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 2201 530 480 530 480 750 245 470 30 18 140 - - 100-250 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 2301 530 480 530 480 850 235 470 35 18 140 - - 100-315 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 2701 620 565 620 565 900 230 530 25 22 180 - - 100-400 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 4001 620 565 620 565 820 255 470 29 22 140 - - 125-250 L 200 150 340 285 295 240 22 22 8 8 3/8’’G 3/8’’G 3/8’’G 2901 620 565 620 565 880 260 530 30 22 180 - - 125-315 L 200 150 340 285 295 240 22 22 8 8 3/8’’G 3/8’’G 3/8’’G 3551 620 565 620 565 920 275 530 32 22 180 - - 125-400 L 200 150 340 285 295 240 22 22 8 8 3/8’’G 3/8’’G 3/8’’G 4351 660 605 660 605 960 250 911 18 22 - - - 125-450 L 200 150 340 285 295 240 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 4802 660 605 660 605 960 250 911 18 22 - - - 125-450 L 200 150 340 285 295 240 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 4802 640 500 730 570 1050 275 635 27 26 X 180 140 125-500 L 150* 125* 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 6001 620 565 620 565 880 325 530 30 22 180 - - 150-250 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 3752 750 565 620 565 880 325 530 30 22 180 - - 150-250 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 3751 620 565 620 565 930 290 530 30 22 180 - - 150-315 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 3901 660 605 660 605 1000 283 530 25 22 180 - - 150-400 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 4201 750 680 750 680 1020 340 530 40 25 180 - - 200-250 L 250 250 395 395 350 350 22 22 12 12 3/8’’G 3/8’’G 3/8’’G 4901 750 650 640 540 1055 322 605 30 30 180 - - 200-315 L 300 250 445 395 400 350 22 22 12 12 2x3/8’’G 3/8’’G 3/8’’G 7602 750 660 640 550 1055 322 605 - 30 180 - - 200-315 L 300 250 445 395 400 350 22 22 12 12 2x3/8’’G 3/8’’G 3/8’’G 7602 750 650 610 510 1000 330 530 - 27 180 - - 250-250 L 300 250 445 395 400 350 22 22 12 12 3/8’’G 3/4’’G 3/8’’G 8001 960 890 960 890 1265 385 605 30 25 300 - - 250-315 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 9502 960 860 800 700 1265 385 605 - 30 300 - - 250-315 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 9201 1025 945 1025 945 1300 385 605 35 25 300 - - 250-400 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 10502 960 860 800 700 1300 385 605 - 30 300 - - 250-400 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 9202 1400 1200 1300 1100 1800 400 1500 40 40 400 - - 300-710 L 400 300 597 483 515 400 25 22 16 12 2x3/4’’G 3/8’’G 3/8’’G 40003 620 480 670 510 1000 330 1150 27 26 - 180 140 250-250 LDS 300 250 483 406 400 350 22 22 12 12 2x3/4’’G 3/8’’G 3/8’’G 9003 670 530 730 570 1200 330 1160 27 26 - 180 140 300-300 LDS 350 300 533 483 460 400 22 22 16 12 2x3/4’’G 3/8’’G 3/8’’G 11003 750 590 820 660 1300 375 1238 27 30 - 200 160 350-250 LDS 400 350 597 533 515 460 25 22 16 16 2x3/4’’G 3/8’’G 3/8’’G 11003 775 615 820 660 1300 375 1215 27 30 - 200 160 350-315 LDS 400 350 597 533 515 460 25 22 16 16 2x3/4’’G 3/8’’G 3/8’’G 12003 807 647 820 660 1400 405 1260 27 30 - 200 160 400-315 LDS 450 400 640 597 565 515 25 25 20 16 2x3/4’’G 3/8’’G 3/8’’G 13003 1020 940 950 870 1580 480 1415 33 28 - 100 180 450-450 LDS 600 450 840 640 725 565 25 25 20 20 2x3/4’’G 3/8’’G 3/8’’G 1500
X= 280 FOR MOTOR SIZE 250÷280 X= 250 FOR MOTOR SIZE 315 ** BARE SHAFT BRONZE PUMP POMPA AD ASSE NUDO IN BRONZO
DIS 1= CAST BASE PIEDE IN FUSIONE DIS 2= WELDED STEEL BASE PIEDE IN CARPENTERIA
PM1 PM2
FEG±5
C B
FEG±5
HL
O
D1
PM1 PM2
g
g'
DNs
DNd
KD
K'D'
N
D1
LH
O
C B
N.4 HOLES ØSFORI
N.4 HOLES ØSFORI
SUCTION FLANGEFLANGIA ASPIRAZIONE
DISCHARGE FLANGEFLANGIA MANDATA
MU-L MU-L
GE
±5
F
C B
PM1
U1
U2
N
PM2
±1
D1
HL
N.4 HOLES ØSFORI
MU-LDS
DIS1 DIS2 DIS3
3
Pos Description Descrizione
1110 Pump casing Corpo pompa
1221 Casing cover Coperchio del corpo
1525 Wear ring Anello di usura
1600 Bush Boccola
2115 Pump shaft Albero della pompa
2240 Impeller Girante
2450 Shaft sleeve Camicia d’albero
2460 Spacer sleeve Bussola distanziatrice
2483 Locating sleeve Bussola bloccaggio
3011 Radial ball bearing Cuscinetto radiale
3017 Angular ball bearing Cuscinetto obliquo
3132 Bearing bracket Supporto
3130 Bearing bracket Supporto doppio
3160 Motor stool Lanterna del motore
3260 Bearing cover Coperchio supporto
4200 Mechanical seal Tenuta meccanica
4213 Mechanical seal cover Coperchio per tenuta
4271 Shaft sleeve Camicia d’albero
4610.1 O-Ring O-Ring
4610.2 O-Ring O-Ring
4610.3 O-Ring O-Ring
4610.4 O-Ring O-Ring
6510 Plug Tappo
6510
1110
1600
4610.3
4271
4213
3132
3011
1525
2460
2240
4610.4
2450
4610.1
1221
4610.2
4200
2115
3017
3160
3170
3260
3130
2483
1525
65101510
6577.1
42006700.1
1110
15216510
6577.22540
38493017
3011
6577.23160
6581
6579
1225
6579
2200
65104609
6576
3260
31304300
21113260
6700.2
6855.1
6855.2
4300
4590
4590
4134
6573
4130
65804120
2450
4610
5110
25206700.3
4300 22916545
5100
SELF-PRIMING VERSIONVERSIONE AUTOADESCANTE
SOFT PACKING VERSIONVERSIONE TENUTA A BADERNA
LONGITUDINAL SECTIONSEZIONE LONGITUDINALE
Pos Description Descrizione
1110 Pump casing Corpo pompa
1225 Casing cover Coperchio del corpo
1510 Wear ring Anello di usura
1521 Wear ring Anello di usura
2111 Pump shaft Albero della pompa
2200 Impeller Girante
2291 Priming stage impeller Girante stellare
2450 Shaft sleeve Camicia d’albero
2520 Shoulder ring Anello spallamento
2540 Deflector Deflettore
3011 Radial ball bearing Cuscinetto radiale
3017 Angular ball bearing Cuscinetto obliquo
3130 Bearing bracket Supporto doppio
3160 Motor stool Lanterna del motore
3260 Bearing cover Coperchio supporto
3849 Greaser Ingrassatore
4120 Stuffing box gland Premitreccia
4130 Gland packing Guarnizione a treccia
4134 Lantern ring Anello lanterna
4200 Mechanical seal Tenuta meccanica
4300 Radial shaft seal Anello di tenuta
4590 Gasket Guarnizione
4609 O-Ring O-Ring
4610 O-Ring O-Ring
5100 Priming stage casing Corpo autoadescante
5110 Priming stage cover Coperchio autoadescante
6510 Plug Tappo
6545 Seeger Seeger
6573 Stud Prigioniero
6576 Screw Vite
6577.1 Screw Vite
6577.2 Screw Vite
6579 Screw Vite
6580 Nut Dado
6581 Impeller nut Dado girante
6700.1 Key Chiavetta
6700.2 Key Chiavetta
6700.3 Key Chiavetta
6855.1 Washer Rosetta
6855.2 Washer Rosetta
654
self priming elementwith liquid ring
elemento autoadescante ad anello liquido
closed impellergirante chiusa
bare shaft versionversione ad asse nudo
Disassembly support groupSmontaggio gruppo supporto
MATERIALS (MU-L)MATERIALI
MAX. WORKING PRESSUREPRESSIONE MAX. ESERCIZIO
CAST IRONGHISA 10 bar
STAINLESS STEEL, BRONZE, SPECIAL ALLOY ACCIAIO INOX, BRONZO, LEGHE SPECIALI 16 bar
NOTE: SPECIAL EXECUTIONS EXCEEDING THE ABOVE LIMITS AVAILABLE ON REQUESTNOTA: ESECUZIONI SPECIALI AL DI FUORI DEI LIMITI SOPRAESPOSTI REALIZZATE SU RICHIESTA
MATERIALS (MU-LDS)MATERIALI
MAX. WORKING PRESSUREPRESSIONE MAX. ESERCIZIO
CAST IRONGHISA 10 bar
STAINLESS STEEL, BRONZE, SPECIAL ALLOY ACCIAIO INOX, BRONZO, LEGHE SPECIALI 16 bar
NOTE: SPECIAL EXECUTIONS EXCEEDING THE ABOVE LIMITS AVAILABLE ON REQUESTNOTA: ESECUZIONI SPECIALI AL DI FUORI DEI LIMITI SOPRAESPOSTI REALIZZATE SU RICHIESTA
MODELS (MU-LDS) MODELLI 6
INTERCHANGEABILITY INTERCAMBIABILITÀ:
CASINGS CORPI 6
IMPELLERSGIRANTI 7
SHAFTSALBERI 7
BEARING BRACKETSSUPPORTI 3
COVERS COPERCHI 6
MECHANICAL SEALS TENUTE MECCANICHE 6
MODELS (MU-L)MODELLI 39
INTERCHANGEABILITY INTERCAMBIABILITÀ:
CASINGS CORPI 39
IMPELLERSGIRANTI 39
SHAFTSALBERI 6
BEARING BRACKETSSUPPORTI 6
COVERS COPERCHI 6
MECHANICAL SEALS TENUTE MECCANICHE 6
close coupled versionversione monoblocco
double suction impellergirante a doppia aspirazione
bare shaft versionversione ad asse nudo
LONGITUDINAL SECTIONSEZIONE LONGITUDINALE
Pos Description Descrizione
1110 Pump casing Corpo pompa
1221 Casing cover Coperchio del corpo
1525 Wear ring Anello di usura
1600 Bush Boccola
2115 Pump shaft Albero della pompa
2240 Impeller Girante
2450 Shaft sleeve Camicia d’albero
2460 Spacer sleeve Bussola distanziatrice
2483 Locating sleeve Bussola bloccaggio
3011 Radial ball bearing Cuscinetto radiale
3017 Angular ball bearing Cuscinetto obliquo
3132 Bearing bracket Supporto
3130 Bearing bracket Supporto doppio
3160 Motor stool Lanterna del motore
3260 Bearing cover Coperchio supporto
4200 Mechanical seal Tenuta meccanica
4213 Mechanical seal cover Coperchio per tenuta
4271 Shaft sleeve Camicia d’albero
4610.1 O-Ring O-Ring
4610.2 O-Ring O-Ring
4610.3 O-Ring O-Ring
4610.4 O-Ring O-Ring
6510 Plug Tappo
6510
1110
1600
4610.3
4271
4213
3132
3011
1525
2460
2240
4610.4
2450
4610.1
1221
4610.2
4200
2115
3017
3160
3170
3260
3130
2483
1525
65101510
6577.1
42006700.1
1110
15216510
6577.22540
38493017
3011
6577.23160
6581
6579
1225
6579
2200
65104609
6576
3260
31304300
21113260
6700.2
6855.1
6855.2
4300
4590
4590
4134
6573
4130
65804120
2450
4610
5110
25206700.3
4300 22916545
5100
SELF-PRIMING VERSIONVERSIONE AUTOADESCANTE
SOFT PACKING VERSIONVERSIONE TENUTA A BADERNA
LONGITUDINAL SECTIONSEZIONE LONGITUDINALE
Pos Description Descrizione
1110 Pump casing Corpo pompa
1225 Casing cover Coperchio del corpo
1510 Wear ring Anello di usura
1521 Wear ring Anello di usura
2111 Pump shaft Albero della pompa
2200 Impeller Girante
2291 Priming stage impeller Girante stellare
2450 Shaft sleeve Camicia d’albero
2520 Shoulder ring Anello spallamento
2540 Deflector Deflettore
3011 Radial ball bearing Cuscinetto radiale
3017 Angular ball bearing Cuscinetto obliquo
3130 Bearing bracket Supporto doppio
3160 Motor stool Lanterna del motore
3260 Bearing cover Coperchio supporto
3849 Greaser Ingrassatore
4120 Stuffing box gland Premitreccia
4130 Gland packing Guarnizione a treccia
4134 Lantern ring Anello lanterna
4200 Mechanical seal Tenuta meccanica
4300 Radial shaft seal Anello di tenuta
4590 Gasket Guarnizione
4609 O-Ring O-Ring
4610 O-Ring O-Ring
5100 Priming stage casing Corpo autoadescante
5110 Priming stage cover Coperchio autoadescante
6510 Plug Tappo
6545 Seeger Seeger
6573 Stud Prigioniero
6576 Screw Vite
6577.1 Screw Vite
6577.2 Screw Vite
6579 Screw Vite
6580 Nut Dado
6581 Impeller nut Dado girante
6700.1 Key Chiavetta
6700.2 Key Chiavetta
6700.3 Key Chiavetta
6855.1 Washer Rosetta
6855.2 Washer Rosetta
654
self priming elementwith liquid ring
elemento autoadescante ad anello liquido
closed impellergirante chiusa
bare shaft versionversione ad asse nudo
Disassembly support groupSmontaggio gruppo supporto
MATERIALS (MU-L)MATERIALI
MAX. WORKING PRESSUREPRESSIONE MAX. ESERCIZIO
CAST IRONGHISA 10 bar
STAINLESS STEEL, BRONZE, SPECIAL ALLOY ACCIAIO INOX, BRONZO, LEGHE SPECIALI 16 bar
NOTE: SPECIAL EXECUTIONS EXCEEDING THE ABOVE LIMITS AVAILABLE ON REQUESTNOTA: ESECUZIONI SPECIALI AL DI FUORI DEI LIMITI SOPRAESPOSTI REALIZZATE SU RICHIESTA
MATERIALS (MU-LDS)MATERIALI
MAX. WORKING PRESSUREPRESSIONE MAX. ESERCIZIO
CAST IRONGHISA 10 bar
STAINLESS STEEL, BRONZE, SPECIAL ALLOY ACCIAIO INOX, BRONZO, LEGHE SPECIALI 16 bar
NOTE: SPECIAL EXECUTIONS EXCEEDING THE ABOVE LIMITS AVAILABLE ON REQUESTNOTA: ESECUZIONI SPECIALI AL DI FUORI DEI LIMITI SOPRAESPOSTI REALIZZATE SU RICHIESTA
MODELS (MU-LDS) MODELLI 6
INTERCHANGEABILITY INTERCAMBIABILITÀ:
CASINGS CORPI 6
IMPELLERSGIRANTI 7
SHAFTSALBERI 7
BEARING BRACKETSSUPPORTI 3
COVERS COPERCHI 6
MECHANICAL SEALS TENUTE MECCANICHE 6
MODELS (MU-L)MODELLI 39
INTERCHANGEABILITY INTERCAMBIABILITÀ:
CASINGS CORPI 39
IMPELLERSGIRANTI 39
SHAFTSALBERI 6
BEARING BRACKETSSUPPORTI 6
COVERS COPERCHI 6
MECHANICAL SEALS TENUTE MECCANICHE 6
close coupled versionversione monoblocco
double suction impellergirante a doppia aspirazione
bare shaft versionversione ad asse nudo
LONGITUDINAL SECTIONSEZIONE LONGITUDINALE
Pos Description Descrizione
1110 Pump casing Corpo pompa
1221 Casing cover Coperchio del corpo
1525 Wear ring Anello di usura
1600 Bush Boccola
2115 Pump shaft Albero della pompa
2240 Impeller Girante
2450 Shaft sleeve Camicia d’albero
2460 Spacer sleeve Bussola distanziatrice
2483 Locating sleeve Bussola bloccaggio
3011 Radial ball bearing Cuscinetto radiale
3017 Angular ball bearing Cuscinetto obliquo
3132 Bearing bracket Supporto
3130 Bearing bracket Supporto doppio
3160 Motor stool Lanterna del motore
3260 Bearing cover Coperchio supporto
4200 Mechanical seal Tenuta meccanica
4213 Mechanical seal cover Coperchio per tenuta
4271 Shaft sleeve Camicia d’albero
4610.1 O-Ring O-Ring
4610.2 O-Ring O-Ring
4610.3 O-Ring O-Ring
4610.4 O-Ring O-Ring
6510 Plug Tappo
6510
1110
1600
4610.3
4271
4213
3132
3011
1525
2460
2240
4610.4
2450
4610.1
1221
4610.2
4200
2115
3017
3160
3170
3260
3130
2483
1525
65101510
6577.1
42006700.1
1110
15216510
6577.22540
38493017
3011
6577.23160
6581
6579
1225
6579
2200
65104609
6576
3260
31304300
21113260
6700.2
6855.1
6855.2
4300
4590
4590
4134
6573
4130
65804120
2450
4610
5110
25206700.3
4300 22916545
5100
SELF-PRIMING VERSIONVERSIONE AUTOADESCANTE
SOFT PACKING VERSIONVERSIONE TENUTA A BADERNA
LONGITUDINAL SECTIONSEZIONE LONGITUDINALE
Pos Description Descrizione
1110 Pump casing Corpo pompa
1225 Casing cover Coperchio del corpo
1510 Wear ring Anello di usura
1521 Wear ring Anello di usura
2111 Pump shaft Albero della pompa
2200 Impeller Girante
2291 Priming stage impeller Girante stellare
2450 Shaft sleeve Camicia d’albero
2520 Shoulder ring Anello spallamento
2540 Deflector Deflettore
3011 Radial ball bearing Cuscinetto radiale
3017 Angular ball bearing Cuscinetto obliquo
3130 Bearing bracket Supporto doppio
3160 Motor stool Lanterna del motore
3260 Bearing cover Coperchio supporto
3849 Greaser Ingrassatore
4120 Stuffing box gland Premitreccia
4130 Gland packing Guarnizione a treccia
4134 Lantern ring Anello lanterna
4200 Mechanical seal Tenuta meccanica
4300 Radial shaft seal Anello di tenuta
4590 Gasket Guarnizione
4609 O-Ring O-Ring
4610 O-Ring O-Ring
5100 Priming stage casing Corpo autoadescante
5110 Priming stage cover Coperchio autoadescante
6510 Plug Tappo
6545 Seeger Seeger
6573 Stud Prigioniero
6576 Screw Vite
6577.1 Screw Vite
6577.2 Screw Vite
6579 Screw Vite
6580 Nut Dado
6581 Impeller nut Dado girante
6700.1 Key Chiavetta
6700.2 Key Chiavetta
6700.3 Key Chiavetta
6855.1 Washer Rosetta
6855.2 Washer Rosetta
654
self priming elementwith liquid ring
elemento autoadescante ad anello liquido
closed impellergirante chiusa
bare shaft versionversione ad asse nudo
Disassembly support groupSmontaggio gruppo supporto
MATERIALS (MU-L)MATERIALI
MAX. WORKING PRESSUREPRESSIONE MAX. ESERCIZIO
CAST IRONGHISA 10 bar
STAINLESS STEEL, BRONZE, SPECIAL ALLOY ACCIAIO INOX, BRONZO, LEGHE SPECIALI 16 bar
NOTE: SPECIAL EXECUTIONS EXCEEDING THE ABOVE LIMITS AVAILABLE ON REQUESTNOTA: ESECUZIONI SPECIALI AL DI FUORI DEI LIMITI SOPRAESPOSTI REALIZZATE SU RICHIESTA
MATERIALS (MU-LDS)MATERIALI
MAX. WORKING PRESSUREPRESSIONE MAX. ESERCIZIO
CAST IRONGHISA 10 bar
STAINLESS STEEL, BRONZE, SPECIAL ALLOY ACCIAIO INOX, BRONZO, LEGHE SPECIALI 16 bar
NOTE: SPECIAL EXECUTIONS EXCEEDING THE ABOVE LIMITS AVAILABLE ON REQUESTNOTA: ESECUZIONI SPECIALI AL DI FUORI DEI LIMITI SOPRAESPOSTI REALIZZATE SU RICHIESTA
MODELS (MU-LDS) MODELLI 6
INTERCHANGEABILITY INTERCAMBIABILITÀ:
CASINGS CORPI 6
IMPELLERSGIRANTI 7
SHAFTSALBERI 7
BEARING BRACKETSSUPPORTI 3
COVERS COPERCHI 6
MECHANICAL SEALS TENUTE MECCANICHE 6
MODELS (MU-L)MODELLI 39
INTERCHANGEABILITY INTERCAMBIABILITÀ:
CASINGS CORPI 39
IMPELLERSGIRANTI 39
SHAFTSALBERI 6
BEARING BRACKETSSUPPORTI 6
COVERS COPERCHI 6
MECHANICAL SEALS TENUTE MECCANICHE 6
close coupled versionversione monoblocco
double suction impellergirante a doppia aspirazione
bare shaft versionversione ad asse nudo
LONGITUDINAL SECTIONSEZIONE LONGITUDINALE
MU-LDSPERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
1450 RPM
CAPACITY PORTATA Q m3/h
32-160
40-160
50-160 65-160
32-200 40-200
40-250
65-400
65-200
80-160
80-200 100-200
65-315
125-250
100-250
65-250
80-250
80-400 100-400125-400
150-400 250-400
250-315
200-315150-315125-315100-315
80-315
150-250
200-250
50-250 250-250250-250
300-300
LDS
LDS
50-200
40-315
LDS
400-315
50-315
125-500
LDS
LDS
350-315
LDS
450-450
350-250
25-160
4 5 10 20 30 40 100 200 300 400 500 1000
2
3
4
5
10
20
30
40
50
100
100
3020 40 50 100 200 300 400 500 1000 2000 80003000 5000
10
20
30
40
50
200
300
400
500160
2000 3000
H feet
USGPM
H mt
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
CAPACITY PORTATA Q m3/h
2900 RPM
10 20 30 40 50 100 200 300 400 500 1000 2000 3000
H feetH mt
32-160
32-200
40-1
60
40-200
40-250
50-160
50-200
50-250
65-160
65-250
65-31550-315
80-160
80-200
80-250
100-200
100-250
100-315125-315
125-250
80-31540-315
25-160
65-200
USGPM
2 3 4 5 10 20 30 40 50 100 200 300 15
20
25
30
40
50
60
70
80
90100
120
140
50
60
70
80
90100
200
300
400
500
500 1000
VERTICAL IN LINE DOUBLE SUCTIONCENTRIFUGAL PUMPSPOMPE CENTRIFUGHE VERTICALI IN LINEA DOPPIA ASPIRAZIONE
DESCRIPTIONSingle stage vertical centrifugal pumps in spacer coupling design. Casing with in-line flanges and with high efficiency double inlet impeller, low NPSH required and balanced axial thrust, flow rate up to 3.500 m3/h.
DESCRIZIONEPompe centrifughe monostadio verticali con giunto elastico spazia-tore. Corpo con flange in-line, girante a doppia aspirazione con alto rendimento, basso NPSH richiesto e spinta assiale bilanciata, portata fino a 3.500 m3/h.
MAIN APPLICATIONS Fresh water, sea water, industrial water, condensate, brine, oils and other clean liquids.Shipbuilding industry: ballast, hull and general services, co-oling, circulation.Land based industry: circulation, cooling, water supply and general services.
PRINCIPALI APPLICAZIONIAcqua dolce, acqua di mare, acqua industriale, condensato, brine, idrocarburi ed altri liquidi puliti.Settore navale: servizi di zavorra, bilanciamento, servizi generali, raf-freddamento, circolazione.Settore industriale: circolazione, raffreddamento, servizi vari.
VERSIONSMU-LDS pumps are now available in six sizes. Wetted ma-terial can be in cast iron, nickel-aluminium bronze, stainless steel or special alloy. Automatic priming system execution by means of ejector or vacuum pump.Special executions according to Naval rules: shock-proof, noise-proof, vibration-proof, non magnetic.
VERSIONI Le pompe MU-LDS sono disponibili in sei grandezze. Le parti bagnate possono essere in ghisa, bronzo al nickel alluminio, acciao inox o leghe speciali. Sistema di autoadescamento automatico con eiettore ad aria o pompa del vuoto.Sono previste costruzioni a norma MARINA MILITARE: an-tishock, antirumore, antivibrazione, amagnetiche.
MAIN FEATURES
CARATTERISTICHE COSTRUTTIVE
MU-LDS pumps are designed in order to offer best possible performance and lowest possible maintenance. BACK PULL-OUT design allows maintenance on internal parts without remo-ving motor and pipes. Easy replacement of be-arings and seal without pump dismantling.
Le pompe MU-LDS sono progettate per offrire le migliori perfor-mance con la minima manutenzione. La costruzione BACK PULL-
OUT permette l’estrazione delle parti interne senza dover rimuovere il motore e le tubazioni. E’ anche possibile la sostituzione della tenuta meccanica e dei cuscinetti senza smontare completamente la pompa.
CASING: Casing is of the double volute type to reduce radial load on impeller and ensure maximum working life of bea-rings and mechanical seal. CORPO: : Il corpo è di tipo a doppia voluta per minimizzare la spinta radia-le sulla girante ed aumentare la durata di cuscinetti e tenuta meccanica.
MECHANICAL SEAL: High quality mechanical seal (silicon carbide/silicon carbide/viton) for a wide range of applica-tions. Mechanical seal is cartridge design for easy installation and removing. Soft packing is also available TENUTA MECCANICA: Tenuta meccanica di alta qualità (carburo di si-licio/carburo di silico/viton) per un ampia gamma di applicazioni. La tenuta è del tipo a cartuccia per una facile installazione e rimozione. E’ disponibile anche la versione con tenuta a baderna.
BEARING BRACKET AND MOTOR STOOL: External grease bearings in special bracket specially designed for ease of maintenance. Bracket design allows the replacement of me-chanical seal and bearings without dismantling the pump completely.The motor stool in welded steel to reduce vibrations has got a wide opening to facilitate maintenance.
SUPPORTO E CARENA: : Cuscinetti a grasso installati in un suppor-
to esterno, progettato ap-positamente per facilitare
le operazioni di manu-tenzione. Il design del supporto permette la sostituzione della tenu-
ta meccanica e dei cu-scinetti senza richiedere lo smontaggio completo della pompa.La carena portamotore in acciaio è caratterizzata da elevata resistenza in modo da annullare le vibrazioni durante il funzionamento. E’ dotata di un ampia aper-tura per le operazioni di manutenzione e smontag-gio delle parti interne.
87
PUMP DIMENSIONSDIMENSIONI POMPA
PUMP TYPETIPO POMPA
FLANGES DIMENSIONSDIMENSIONI FLANGE
(UNI 2223-2229 PN 10 UNI 2223-2229 PN 16*)
HOLES N.N. FORI
DRAI
NAGE
DREN
AGGI
O
V/GA
UGE
VUOT
OMET
RO
P/GA
UGE
MAN
OMET
RO
WEIGHT**PESO**
DIS B C E F G H L N S O U1 U2 MU DNs DNd D D’ K K’ g g’ DNs DNd D1 PM1 PM2 Kg1 320 270 320 270 360 100 237 19 18 140 - - 25-160 L 40 25 150 115 110 85 18 14 4 4 1/4’’G 1/4’’G 1/4’’G 601 360 310 360 310 395 130 360 19 18 140 - - 32-160 L 50 40 165 150 125 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 901 350 295 350 295 395 135 360 26 18 140 - - 32-200 L 50 40 165 150 125 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 901 350 295 350 295 420 145 360 24 18 140 - - 40-160 L 65 50 185 165 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 951 360 310 360 310 440 150 360 27 18 140 - - 40-200 L 65 50 185 165 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1001 360 310 360 310 475 135 360 24 18 140 - - 40-250 L 65 50 185 165 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1051 520 465 520 465 700 165 470 27 18 140 - - 40-315 L 65 50 185 165 145 125 18 18 4 4 3/8’’G 3/8’’G 3/8’’G 2351 350 295 350 295 450 155 360 27 18 140 - - 50-160 L 80 65 200 185 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1001 360 310 360 310 480 150 360 22 18 140 - - 50-200 L 80 65 200 185 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1001 425 370 425 370 510 150 360 22 18 140 - - 50-250 L 80 65 200 185 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1201 520 465 520 465 760 160 470 22 18 140 - - 50-315 L 80 65 200 185 160 145 18 18 4 4 3/8’’G 3/8’’G 3/8’’G 2451 385 330 385 330 510 165 360 27 18 140 - - 65-160 L 100 80 220 200 180 160 18 18 8 4 1/4’’G 1/4’’G 1/4’’G 1101 415 360 415 360 510 160 360 22 18 140 - - 65-200 L 100 80 220 200 180 160 18 18 8 4 1/4’’G 1/4’’G 1/4’’G 1151 455 400 455 400 705 193 470 28 18 140 - - 65-250 L 100 80 220 200 180 160 18 18 8 4 3/8’’G 3/8’’G 3/8’’G 2001 520 465 520 465 760 170 470 27 18 140 - - 65-315 L 100 80 220 200 180 160 18 18 8 4 3/8’’G 3/8’’G 3/8’’G 2501 620 565 620 565 850 205 470 40 22 140 - - 65-400 L 100 80 220 200 180 160 18 18 8 4 3/8’’G 3/8’’G 3/8’’G 3051 415 360 415 360 540 170 360 22 18 140 - - 80-160 L 125 100 250 220 210 180 18 18 8 8 1/4’’G 1/4’’G 1/4’’G 1251 450 400 450 400 720 215 470 22 18 140 - - 80-200 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 2001 455 400 455 400 720 196 470 22 18 140 - - 80-250 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 2201 520 465 520 465 780 205 470 27 18 140 - - 80-315 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 2601 620 565 620 565 890 218 530 25 22 180 - - 80-400 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 3751 520 465 520 465 730 235 470 25 18 140 - - 100-200 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 2201 530 480 530 480 750 245 470 30 18 140 - - 100-250 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 2301 530 480 530 480 850 235 470 35 18 140 - - 100-315 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 2701 620 565 620 565 900 230 530 25 22 180 - - 100-400 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 4001 620 565 620 565 820 255 470 29 22 140 - - 125-250 L 200 150 340 285 295 240 22 22 8 8 3/8’’G 3/8’’G 3/8’’G 2901 620 565 620 565 880 260 530 30 22 180 - - 125-315 L 200 150 340 285 295 240 22 22 8 8 3/8’’G 3/8’’G 3/8’’G 3551 620 565 620 565 920 275 530 32 22 180 - - 125-400 L 200 150 340 285 295 240 22 22 8 8 3/8’’G 3/8’’G 3/8’’G 4351 660 605 660 605 960 250 911 18 22 - - - 125-450 L 200 150 340 285 295 240 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 4802 660 605 660 605 960 250 911 18 22 - - - 125-450 L 200 150 340 285 295 240 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 4802 640 500 730 570 1050 275 635 27 26 X 180 140 125-500 L 150* 125* 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 6001 620 565 620 565 880 325 530 30 22 180 - - 150-250 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 3752 750 565 620 565 880 325 530 30 22 180 - - 150-250 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 3751 620 565 620 565 930 290 530 30 22 180 - - 150-315 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 3901 660 605 660 605 1000 283 530 25 22 180 - - 150-400 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 4201 750 680 750 680 1020 340 530 40 25 180 - - 200-250 L 250 250 395 395 350 350 22 22 12 12 3/8’’G 3/8’’G 3/8’’G 4901 750 650 640 540 1055 322 605 30 30 180 - - 200-315 L 300 250 445 395 400 350 22 22 12 12 2x3/8’’G 3/8’’G 3/8’’G 7602 750 660 640 550 1055 322 605 - 30 180 - - 200-315 L 300 250 445 395 400 350 22 22 12 12 2x3/8’’G 3/8’’G 3/8’’G 7602 750 650 610 510 1000 330 530 - 27 180 - - 250-250 L 300 250 445 395 400 350 22 22 12 12 3/8’’G 3/4’’G 3/8’’G 8001 960 890 960 890 1265 385 605 30 25 300 - - 250-315 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 9502 960 860 800 700 1265 385 605 - 30 300 - - 250-315 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 9201 1025 945 1025 945 1300 385 605 35 25 300 - - 250-400 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 10502 960 860 800 700 1300 385 605 - 30 300 - - 250-400 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 9202 1400 1200 1300 1100 1800 400 1500 40 40 400 - - 300-710 L 400 300 597 483 515 400 25 22 16 12 2x3/4’’G 3/8’’G 3/8’’G 40003 620 480 670 510 1000 330 1150 27 26 - 180 140 250-250 LDS 300 250 483 406 400 350 22 22 12 12 2x3/4’’G 3/8’’G 3/8’’G 9003 670 530 730 570 1200 330 1160 27 26 - 180 140 300-300 LDS 350 300 533 483 460 400 22 22 16 12 2x3/4’’G 3/8’’G 3/8’’G 11003 750 590 820 660 1300 375 1238 27 30 - 200 160 350-250 LDS 400 350 597 533 515 460 25 22 16 16 2x3/4’’G 3/8’’G 3/8’’G 11003 775 615 820 660 1300 375 1215 27 30 - 200 160 350-315 LDS 400 350 597 533 515 460 25 22 16 16 2x3/4’’G 3/8’’G 3/8’’G 12003 807 647 820 660 1400 405 1260 27 30 - 200 160 400-315 LDS 450 400 640 597 565 515 25 25 20 16 2x3/4’’G 3/8’’G 3/8’’G 13003 1020 940 950 870 1580 480 1415 33 28 - 100 180 450-450 LDS 600 450 840 640 725 565 25 25 20 20 2x3/4’’G 3/8’’G 3/8’’G 1500
X= 280 FOR MOTOR SIZE 250÷280 X= 250 FOR MOTOR SIZE 315 ** BARE SHAFT BRONZE PUMP POMPA AD ASSE NUDO IN BRONZO
DIS 1= CAST BASE PIEDE IN FUSIONE DIS 2= WELDED STEEL BASE PIEDE IN CARPENTERIA
PM1 PM2
FEG±5
C B
FEG±5
HL
O
D1
PM1 PM2
g
g'
DNs
DNd
KD
K'D'
N
D1
LH
O
C B
N.4 HOLES ØSFORI
N.4 HOLES ØSFORI
SUCTION FLANGEFLANGIA ASPIRAZIONE
DISCHARGE FLANGEFLANGIA MANDATA
MU-L MU-L
GE
±5
F
C B
PM1
U1
U2
N
PM2
±1
D1
HL
N.4 HOLES ØSFORI
MU-LDS
DIS1 DIS2 DIS3
3
MU-LDSPERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
1450 RPM
CAPACITY PORTATA Q m3/h
32-160
40-160
50-160 65-160
32-200 40-200
40-250
65-400
65-200
80-160
80-200 100-200
65-315
125-250
100-250
65-250
80-250
80-400 100-400125-400
150-400 250-400
250-315
200-315150-315125-315100-315
80-315
150-250
200-250
50-250 250-250250-250
300-300
LDS
LDS
50-200
40-315
LDS
400-315
50-315
125-500
LDS
LDS
350-315
LDS
450-450
350-250
25-160
4 5 10 20 30 40 100 200 300 400 500 1000
2
3
4
5
10
20
30
40
50
100
100
3020 40 50 100 200 300 400 500 1000 2000 80003000 5000
10
20
30
40
50
200
300
400
500160
2000 3000
H feet
USGPM
H mt
PERFORMANCES PRESTAZIONI
HEA
D
PREV
ALE
NZA
CAPACITY PORTATA Q m3/h
2900 RPM
10 20 30 40 50 100 200 300 400 500 1000 2000 3000
H feetH mt
32-160
32-200
40-1
60
40-200
40-250
50-160
50-200
50-250
65-160
65-250
65-31550-315
80-160
80-200
80-250
100-200
100-250
100-315125-315
125-250
80-31540-315
25-160
65-200
USGPM
2 3 4 5 10 20 30 40 50 100 200 300 15
20
25
30
40
50
60
70
80
90100
120
140
50
60
70
80
90100
200
300
400
500
500 1000
VERTICAL IN LINE DOUBLE SUCTIONCENTRIFUGAL PUMPSPOMPE CENTRIFUGHE VERTICALI IN LINEA DOPPIA ASPIRAZIONE
DESCRIPTIONSingle stage vertical centrifugal pumps in spacer coupling design. Casing with in-line flanges and with high efficiency double inlet impeller, low NPSH required and balanced axial thrust, flow rate up to 3.500 m3/h.
DESCRIZIONEPompe centrifughe monostadio verticali con giunto elastico spazia-tore. Corpo con flange in-line, girante a doppia aspirazione con alto rendimento, basso NPSH richiesto e spinta assiale bilanciata, portata fino a 3.500 m3/h.
MAIN APPLICATIONS Fresh water, sea water, industrial water, condensate, brine, oils and other clean liquids.Shipbuilding industry: ballast, hull and general services, co-oling, circulation.Land based industry: circulation, cooling, water supply and general services.
PRINCIPALI APPLICAZIONIAcqua dolce, acqua di mare, acqua industriale, condensato, brine, idrocarburi ed altri liquidi puliti.Settore navale: servizi di zavorra, bilanciamento, servizi generali, raf-freddamento, circolazione.Settore industriale: circolazione, raffreddamento, servizi vari.
VERSIONSMU-LDS pumps are now available in six sizes. Wetted ma-terial can be in cast iron, nickel-aluminium bronze, stainless steel or special alloy. Automatic priming system execution by means of ejector or vacuum pump.Special executions according to Naval rules: shock-proof, noise-proof, vibration-proof, non magnetic.
VERSIONI Le pompe MU-LDS sono disponibili in sei grandezze. Le parti bagnate possono essere in ghisa, bronzo al nickel alluminio, acciao inox o leghe speciali. Sistema di autoadescamento automatico con eiettore ad aria o pompa del vuoto.Sono previste costruzioni a norma MARINA MILITARE: an-tishock, antirumore, antivibrazione, amagnetiche.
MAIN FEATURES
CARATTERISTICHE COSTRUTTIVE
MU-LDS pumps are designed in order to offer best possible performance and lowest possible maintenance. BACK PULL-OUT design allows maintenance on internal parts without remo-ving motor and pipes. Easy replacement of be-arings and seal without pump dismantling.
Le pompe MU-LDS sono progettate per offrire le migliori perfor-mance con la minima manutenzione. La costruzione BACK PULL-
OUT permette l’estrazione delle parti interne senza dover rimuovere il motore e le tubazioni. E’ anche possibile la sostituzione della tenuta meccanica e dei cuscinetti senza smontare completamente la pompa.
CASING: Casing is of the double volute type to reduce radial load on impeller and ensure maximum working life of bea-rings and mechanical seal. CORPO: : Il corpo è di tipo a doppia voluta per minimizzare la spinta radia-le sulla girante ed aumentare la durata di cuscinetti e tenuta meccanica.
MECHANICAL SEAL: High quality mechanical seal (silicon carbide/silicon carbide/viton) for a wide range of applica-tions. Mechanical seal is cartridge design for easy installation and removing. Soft packing is also available TENUTA MECCANICA: Tenuta meccanica di alta qualità (carburo di si-licio/carburo di silico/viton) per un ampia gamma di applicazioni. La tenuta è del tipo a cartuccia per una facile installazione e rimozione. E’ disponibile anche la versione con tenuta a baderna.
BEARING BRACKET AND MOTOR STOOL: External grease bearings in special bracket specially designed for ease of maintenance. Bracket design allows the replacement of me-chanical seal and bearings without dismantling the pump completely.The motor stool in welded steel to reduce vibrations has got a wide opening to facilitate maintenance.
SUPPORTO E CARENA: : Cuscinetti a grasso installati in un suppor-
to esterno, progettato ap-positamente per facilitare
le operazioni di manu-tenzione. Il design del supporto permette la sostituzione della tenu-
ta meccanica e dei cu-scinetti senza richiedere lo smontaggio completo della pompa.La carena portamotore in acciaio è caratterizzata da elevata resistenza in modo da annullare le vibrazioni durante il funzionamento. E’ dotata di un ampia aper-tura per le operazioni di manutenzione e smontag-gio delle parti interne.
87
PUMP DIMENSIONSDIMENSIONI POMPA
PUMP TYPETIPO POMPA
FLANGES DIMENSIONSDIMENSIONI FLANGE
(UNI 2223-2229 PN 10 UNI 2223-2229 PN 16*)
HOLES N.N. FORI
DRAI
NAGE
DREN
AGGI
O
V/GA
UGE
VUOT
OMET
RO
P/GA
UGE
MAN
OMET
RO
WEIGHT**PESO**
DIS B C E F G H L N S O U1 U2 MU DNs DNd D D’ K K’ g g’ DNs DNd D1 PM1 PM2 Kg1 320 270 320 270 360 100 237 19 18 140 - - 25-160 L 40 25 150 115 110 85 18 14 4 4 1/4’’G 1/4’’G 1/4’’G 601 360 310 360 310 395 130 360 19 18 140 - - 32-160 L 50 40 165 150 125 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 901 350 295 350 295 395 135 360 26 18 140 - - 32-200 L 50 40 165 150 125 110 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 901 350 295 350 295 420 145 360 24 18 140 - - 40-160 L 65 50 185 165 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 951 360 310 360 310 440 150 360 27 18 140 - - 40-200 L 65 50 185 165 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1001 360 310 360 310 475 135 360 24 18 140 - - 40-250 L 65 50 185 165 145 125 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1051 520 465 520 465 700 165 470 27 18 140 - - 40-315 L 65 50 185 165 145 125 18 18 4 4 3/8’’G 3/8’’G 3/8’’G 2351 350 295 350 295 450 155 360 27 18 140 - - 50-160 L 80 65 200 185 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1001 360 310 360 310 480 150 360 22 18 140 - - 50-200 L 80 65 200 185 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1001 425 370 425 370 510 150 360 22 18 140 - - 50-250 L 80 65 200 185 160 145 18 18 4 4 1/4’’G 1/4’’G 1/4’’G 1201 520 465 520 465 760 160 470 22 18 140 - - 50-315 L 80 65 200 185 160 145 18 18 4 4 3/8’’G 3/8’’G 3/8’’G 2451 385 330 385 330 510 165 360 27 18 140 - - 65-160 L 100 80 220 200 180 160 18 18 8 4 1/4’’G 1/4’’G 1/4’’G 1101 415 360 415 360 510 160 360 22 18 140 - - 65-200 L 100 80 220 200 180 160 18 18 8 4 1/4’’G 1/4’’G 1/4’’G 1151 455 400 455 400 705 193 470 28 18 140 - - 65-250 L 100 80 220 200 180 160 18 18 8 4 3/8’’G 3/8’’G 3/8’’G 2001 520 465 520 465 760 170 470 27 18 140 - - 65-315 L 100 80 220 200 180 160 18 18 8 4 3/8’’G 3/8’’G 3/8’’G 2501 620 565 620 565 850 205 470 40 22 140 - - 65-400 L 100 80 220 200 180 160 18 18 8 4 3/8’’G 3/8’’G 3/8’’G 3051 415 360 415 360 540 170 360 22 18 140 - - 80-160 L 125 100 250 220 210 180 18 18 8 8 1/4’’G 1/4’’G 1/4’’G 1251 450 400 450 400 720 215 470 22 18 140 - - 80-200 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 2001 455 400 455 400 720 196 470 22 18 140 - - 80-250 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 2201 520 465 520 465 780 205 470 27 18 140 - - 80-315 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 2601 620 565 620 565 890 218 530 25 22 180 - - 80-400 L 125 100 250 220 210 180 18 18 8 8 3/8’’G 3/8’’G 3/8’’G 3751 520 465 520 465 730 235 470 25 18 140 - - 100-200 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 2201 530 480 530 480 750 245 470 30 18 140 - - 100-250 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 2301 530 480 530 480 850 235 470 35 18 140 - - 100-315 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 2701 620 565 620 565 900 230 530 25 22 180 - - 100-400 L 150 125 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 4001 620 565 620 565 820 255 470 29 22 140 - - 125-250 L 200 150 340 285 295 240 22 22 8 8 3/8’’G 3/8’’G 3/8’’G 2901 620 565 620 565 880 260 530 30 22 180 - - 125-315 L 200 150 340 285 295 240 22 22 8 8 3/8’’G 3/8’’G 3/8’’G 3551 620 565 620 565 920 275 530 32 22 180 - - 125-400 L 200 150 340 285 295 240 22 22 8 8 3/8’’G 3/8’’G 3/8’’G 4351 660 605 660 605 960 250 911 18 22 - - - 125-450 L 200 150 340 285 295 240 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 4802 660 605 660 605 960 250 911 18 22 - - - 125-450 L 200 150 340 285 295 240 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 4802 640 500 730 570 1050 275 635 27 26 X 180 140 125-500 L 150* 125* 285 250 240 210 22 18 8 8 3/8’’G 3/8’’G 3/8’’G 6001 620 565 620 565 880 325 530 30 22 180 - - 150-250 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 3752 750 565 620 565 880 325 530 30 22 180 - - 150-250 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 3751 620 565 620 565 930 290 530 30 22 180 - - 150-315 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 3901 660 605 660 605 1000 283 530 25 22 180 - - 150-400 L 250 200 395 340 350 295 22 22 12 8 3/8’’G 3/8’’G 3/8’’G 4201 750 680 750 680 1020 340 530 40 25 180 - - 200-250 L 250 250 395 395 350 350 22 22 12 12 3/8’’G 3/8’’G 3/8’’G 4901 750 650 640 540 1055 322 605 30 30 180 - - 200-315 L 300 250 445 395 400 350 22 22 12 12 2x3/8’’G 3/8’’G 3/8’’G 7602 750 660 640 550 1055 322 605 - 30 180 - - 200-315 L 300 250 445 395 400 350 22 22 12 12 2x3/8’’G 3/8’’G 3/8’’G 7602 750 650 610 510 1000 330 530 - 27 180 - - 250-250 L 300 250 445 395 400 350 22 22 12 12 3/8’’G 3/4’’G 3/8’’G 8001 960 890 960 890 1265 385 605 30 25 300 - - 250-315 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 9502 960 860 800 700 1265 385 605 - 30 300 - - 250-315 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 9201 1025 945 1025 945 1300 385 605 35 25 300 - - 250-400 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 10502 960 860 800 700 1300 385 605 - 30 300 - - 250-400 L 350 300 505 445 460 400 22 22 16 12 3/8’’G 3/8’’G 3/8’’G 9202 1400 1200 1300 1100 1800 400 1500 40 40 400 - - 300-710 L 400 300 597 483 515 400 25 22 16 12 2x3/4’’G 3/8’’G 3/8’’G 40003 620 480 670 510 1000 330 1150 27 26 - 180 140 250-250 LDS 300 250 483 406 400 350 22 22 12 12 2x3/4’’G 3/8’’G 3/8’’G 9003 670 530 730 570 1200 330 1160 27 26 - 180 140 300-300 LDS 350 300 533 483 460 400 22 22 16 12 2x3/4’’G 3/8’’G 3/8’’G 11003 750 590 820 660 1300 375 1238 27 30 - 200 160 350-250 LDS 400 350 597 533 515 460 25 22 16 16 2x3/4’’G 3/8’’G 3/8’’G 11003 775 615 820 660 1300 375 1215 27 30 - 200 160 350-315 LDS 400 350 597 533 515 460 25 22 16 16 2x3/4’’G 3/8’’G 3/8’’G 12003 807 647 820 660 1400 405 1260 27 30 - 200 160 400-315 LDS 450 400 640 597 565 515 25 25 20 16 2x3/4’’G 3/8’’G 3/8’’G 13003 1020 940 950 870 1580 480 1415 33 28 - 100 180 450-450 LDS 600 450 840 640 725 565 25 25 20 20 2x3/4’’G 3/8’’G 3/8’’G 1500
X= 280 FOR MOTOR SIZE 250÷280 X= 250 FOR MOTOR SIZE 315 ** BARE SHAFT BRONZE PUMP POMPA AD ASSE NUDO IN BRONZO
DIS 1= CAST BASE PIEDE IN FUSIONE DIS 2= WELDED STEEL BASE PIEDE IN CARPENTERIA
PM1 PM2
FEG±5
C B
FEG±5
HL
O
D1
PM1 PM2
g
g'
DNs
DNd
KD
K'D'
N
D1
LH
O
C B
N.4 HOLES ØSFORI
N.4 HOLES ØSFORI
SUCTION FLANGEFLANGIA ASPIRAZIONE
DISCHARGE FLANGEFLANGIA MANDATA
MU-L MU-L
GE
±5
F
C B
PM1
U1
U2
N
PM2
±1
D1
HL
N.4 HOLES ØSFORI
MU-LDS
DIS1 DIS2 DIS3
3
2
39
40-160
32-160
32-200
50-16065-160
80-160
40-200
40-250
50-200
50-250
80-315100-315
125-315
200-315
125-450125-400
150-400100-400
80-400
250-315
200-250150-250
125-250100-250
80-250
65-250
80-200 100-200
65-200
65-400250-400
LDS
300-
300
150-31540-315
LDS
400-315
50-31565-315
125-500
LDS
250-250
LDS
350-315
LDS
350-250
25-160
250-250
PERFORMANCE PRESTAZIONI
HEA
D
PREV
ALE
NZA
H mt
CAPACITY PORTATA Q m3/h
1750 RPM
4 5 10 20 30 40 50 100 200 300 400 500 1000
2
3
4
5
10
20
30
40
50
100
100
30 40 50 100 200 300 400 500 1000 2000 80003000 5000
10
20
30
40
50
200
300
400
500160
2000 3000 4000
H feet
USGPM
HEA
D
PREV
ALE
NZA
3500 RPM
10 20 30 40 50 100 200 300 400 500 1000 2000 300050
32-160
32-200
40-160
50-160
40-200
40-250
50-200
50-250
65-160
65-200
65-250
80-160
80-200
125-250
100-250
100-200
80-250
Q m /h3
25-160
PERFORMANCES PRESTAZIONI
CAPACITY PORTATA Q m3/h
2 3 4 5 10 20 30 40 50 100 200 300 700 15
20
25
30
40
50
60
70
80
90100
120
140
160
50
60
70
80
90100
200
300
400
500
H mt
USGPM
H feet
2
MU
-L
MU
-LD
S 01
- 07
/200
8
w
ww
.lize
a.co
m
www.pompegarbarino.com
POMPE GARBARINO S.p.A.
Headquarters:Via Marenco, 44 - 15011 Acqui Terme (AL) - Italy - Tel. +39 0144.388671 - Fax +39 0144.55260
E-mail: info@pompegarbarino.it
Milan Branch:Viale Andrea Doria, 31 - 20124 Milano - Italy - Tel. +39 02.67070037 - Fax +39 02.67070097
E-mail: info.filiale@pompegarbarino.it
ATEX on request